1
|
Wang J, Ma S, Jeong SY, Yang W, Li J, Han YW, Feng K, Guo X. High-performance n-type organic thermoelectrics enabled by modulating cyano-functionalized polythiophene backbones. Faraday Discuss 2024; 250:335-347. [PMID: 37965681 DOI: 10.1039/d3fd00135k] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/16/2023]
Abstract
The scarcity of n-type polymers with high electrical conductivity (σ) and power factor (PF) is the major challenge for organic thermoelectrics (OTEs). By integrating cyano functionalities and an intramolecular conformation lock, we herein synthesize a new electron-deficient building block, CNg4T2, bearing long 1,4,7,10-tetraoxahendecyl side chains, and then further develop two n-type polythiophene derivatives, CNg4T2-2FT and CNg4T2-CNT2, with 3,4-difluorothiophene and 3,3'-dicyano-2,2'-bithiophene as co-units, respectively. Compared with CNg4T2-2FT, CNg4T2-CNT2 features a deeper-positioned lowest unoccupied molecular orbital (LUMO) while maintaining a high degree of backbone coplanarity. As a consequence, the CNg4T2-CNT2 film with molecular dopant N-DMBI delivered an impressive σ of 13.2 S cm-1 and a high PF of up to 10.84 μW m-1 K-2, significantly outperforming CNg4T2-2FT and benchmark n-type polymer N2200 films. To the best of our knowledge, this PF of CNg4T2-CNT2 devices is the highest value for n-type polythiophenes in OTEs. Further characterizations indicate that the high performance of CNg4T2-CNT2-based devices is attributed to the high doping efficiency and ordered packing of polymer chains. Our study demonstrates that CNg4T2 is a highly appealing electron-deficient building block for n-type OTE polymers and also suggests that fine-tuning of the polymer backbone is a powerful approach to accessing high-performance n-type polymers for OTE devices.
Collapse
Affiliation(s)
- Junwei Wang
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China.
| | - Suxiang Ma
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China.
| | - Sang Young Jeong
- Department of Chemistry, Korea University, Anamro 145, Seoul 02841, Republic of Korea
| | - Wanli Yang
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China.
| | - Jianfeng Li
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China.
| | - Young Woo Han
- Department of Chemistry, Korea University, Anamro 145, Seoul 02841, Republic of Korea
| | - Kui Feng
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China.
- Academy for Advanced Interdisciplinary Studies, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China
| | - Xugang Guo
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China.
- Guangdong Provincial Key Laboratory of Functional Oxide Materials and Devices, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China
| |
Collapse
|
2
|
Tu L, Wang J, Wu Z, Li J, Yang W, Liu B, Wu S, Xia X, Wang Y, Woo HY, Shi Y. Cyano-Functionalized Pyrazine: A Structurally Simple and Easily Accessible Electron-Deficient Building Block for n-Type Organic Thermoelectric Polymers. Angew Chem Int Ed Engl 2024; 63:e202319658. [PMID: 38265195 DOI: 10.1002/anie.202319658] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/19/2023] [Revised: 01/16/2024] [Accepted: 01/22/2024] [Indexed: 01/25/2024]
Abstract
Developing low-cost and high-performance n-type polymer semiconductors is essential to accelerate the application of organic thermoelectrics (OTEs). To achieve this objective, it is critical to design strong electron-deficient building blocks with simple structure and easy synthesis, which are essential for the development of n-type polymer semiconductors. Herein, we synthesized two cyano-functionalized highly electron-deficient building blocks, namely 3,6-dibromopyrazine-2-carbonitrile (CNPz) and 3,6-Dibromopyrazine-2,5-dicarbonitrile (DCNPz), which feature simple structures and facile synthesis. CNPz and DCNPz can be obtained via only one-step reaction and three-step reactions from cheap raw materials, respectively. Based on CNPz and DCNPz, two acceptor-acceptor (A-A) polymers, P(DPP-CNPz) and P(DPP-DCNPz) are successfully developed, featuring deep-positioned lowest unoccupied molecular orbital (LUMO) energy levels, which are beneficial to n-type organic thin-film transistors (OTFTs) and OTEs performance. An optimal unipolar electron mobility of 0.85 and 1.85 cm2 V-1 s-1 is obtained for P(DPP-CNPz) and P(DPP-DCNPz), respectively. When doped with N-DMBI, P(DPP-CNPz) and P(DPP-DCNPz) show high n-type electrical conductivities/power factors of 25.3 S cm-1 /41.4 μW m-1 K-2 , and 33.9 S cm-1 /30.4 μW m-1 K-2 , respectively. Hence, the cyano-functionalized pyrazine CNPz and DCNPz represent a new class of structurally simple, low-cost and readily accessible electron-deficient building block for constructing n-type polymer semiconductors.
Collapse
Affiliation(s)
- Lijun Tu
- Key Laboratory of Functional Molecular Solids, Ministry of Education, School of Chemistry and Materials Science, Anhui Normal University, No.189, Jiuhua South Road, Wuhu, Anhui, 241002, China
| | - Junwei Wang
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong, 518055, China
| | - Ziang Wu
- Department of Chemistry, College of Science, Korea University, 145 Anam-ro, Seongbuk-gu, Seoul, 136-713, Korea
| | - Jianfeng Li
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong, 518055, China
| | - Wanli Yang
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong, 518055, China
| | - Bin Liu
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong, 518055, China
| | - Siqi Wu
- Key Laboratory of Functional Molecular Solids, Ministry of Education, School of Chemistry and Materials Science, Anhui Normal University, No.189, Jiuhua South Road, Wuhu, Anhui, 241002, China
| | - Xiaomin Xia
- Key Laboratory of Functional Molecular Solids, Ministry of Education, School of Chemistry and Materials Science, Anhui Normal University, No.189, Jiuhua South Road, Wuhu, Anhui, 241002, China
| | - Yimei Wang
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong, 518055, China
| | - Han Young Woo
- Department of Chemistry, College of Science, Korea University, 145 Anam-ro, Seongbuk-gu, Seoul, 136-713, Korea
| | - Yongqiang Shi
- Key Laboratory of Functional Molecular Solids, Ministry of Education, School of Chemistry and Materials Science, Anhui Normal University, No.189, Jiuhua South Road, Wuhu, Anhui, 241002, China
| |
Collapse
|
3
|
Hu Z, Wang J, Cui C, Liu T, Li Y, Song L, Wen S, Bao X. Efficient and Stable All-Polymer Solar Cells Enabled by Dual Working Mechanism. SMALL (WEINHEIM AN DER BERGSTRASSE, GERMANY) 2024:e2311648. [PMID: 38402429 DOI: 10.1002/smll.202311648] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 12/14/2023] [Revised: 02/01/2024] [Indexed: 02/26/2024]
Abstract
Ternary strategy with integration characteristics and adaptability is a simple and effective method for blooming of the performance of photovoltaic devices. Herein, a novel wideband gap polymer donor PBB2-Hs is synthesized as the guest component to optimize all-polymer solar cells (all-PSCs). High-energy photon absorption and long exciton lifetime of PBB2-Hs constitute efficient energy transfer. Good miscibility and cascade energy levels promote the formation of alloy-like structure between PBB2-Hs and host system. The dual working mechanisms greatly improve photon capture and charge transfer in active layers. Additionally, the introduction of PBB2-Hs also optimizes the ordered molecular stacking of acceptors and suppresses molecular peristalsis. Upon adding 15 wt% PBB2-Hs, the ternary all-PSC achieved a champion efficiency of 17.66%, and can still maintain 82% photostability (24 h) and 91% storage stability (1000 h) of the original PCE. Moreover, the strong molecular stacking and entanglement between PBB2-Hs and the host material increased the elongation at break of ternary blend film by 1.6 times (16.2%), allowing the flexible device to maintain 83% of the original efficiency after 800 bends (R = 5 mm). This work highlights the effectiveness of guest polymer on simultaneously improving photovoltaic performance, photostability and mechanical stability in all-PSCs.
Collapse
Affiliation(s)
- Zunyuan Hu
- College of Materials Science and Engineering, Shandong University of Science and Technology, Qingdao, 266590, China
- Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, Qingdao, 266101, China
- Functional Laboratory of Solar Energy, Shandong Energy Institute, Qingdao, 266101, China
| | - Jianxiao Wang
- Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, Qingdao, 266101, China
- Functional Laboratory of Solar Energy, Shandong Energy Institute, Qingdao, 266101, China
- Qingdao New Energy Shandong Laboratory, Qingdao, 266101, China
| | - Chuanlong Cui
- College of Materials Science and Engineering, Shandong University of Science and Technology, Qingdao, 266590, China
- Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, Qingdao, 266101, China
- Functional Laboratory of Solar Energy, Shandong Energy Institute, Qingdao, 266101, China
| | - Tong Liu
- Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, Qingdao, 266101, China
- Functional Laboratory of Solar Energy, Shandong Energy Institute, Qingdao, 266101, China
- Qingdao New Energy Shandong Laboratory, Qingdao, 266101, China
| | - Yonghai Li
- Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, Qingdao, 266101, China
- Functional Laboratory of Solar Energy, Shandong Energy Institute, Qingdao, 266101, China
- Qingdao New Energy Shandong Laboratory, Qingdao, 266101, China
| | - Liang Song
- College of Materials Science and Engineering, Shandong University of Science and Technology, Qingdao, 266590, China
| | - Shuguang Wen
- Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, Qingdao, 266101, China
- Functional Laboratory of Solar Energy, Shandong Energy Institute, Qingdao, 266101, China
- Qingdao New Energy Shandong Laboratory, Qingdao, 266101, China
| | - Xichang Bao
- College of Materials Science and Engineering, Shandong University of Science and Technology, Qingdao, 266590, China
- Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, Qingdao, 266101, China
- Functional Laboratory of Solar Energy, Shandong Energy Institute, Qingdao, 266101, China
- Qingdao New Energy Shandong Laboratory, Qingdao, 266101, China
| |
Collapse
|
4
|
Wu J, Fu C, Chen B, Rong X, Lu Z, Huang Y. Isomeric Effect of a π Bridge in an IDT-Based Nonfused Electron Photovoltaic Acceptor. Chemistry 2024; 30:e202302624. [PMID: 37806959 DOI: 10.1002/chem.202302624] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/11/2023] [Revised: 09/29/2023] [Accepted: 10/07/2023] [Indexed: 10/10/2023]
Abstract
A pair of isomers, IDT-BOF containing S⋅⋅⋅O/F⋅⋅⋅H noncovalently configurational locks and IDT-BFO containing F⋅⋅⋅H/O⋅⋅⋅H noncovalently configurational locks, with an acceptor-π-donor-π-acceptor (A-π-D-π-A) structure have been designed and synthesized by choosing 4,9-dihydro-s-indaceno[1,2-b : 5,6-b']dithiophene (IDT) as the D unit, an F/n-hexyloxy substituted phenyl ring as π bridge, and 3-(dicyanomethylidene)indan-1-one as the A unit. Owing to the S⋅⋅⋅O/F⋅⋅⋅H or F⋅⋅⋅H/O⋅⋅⋅H noncovalently configurational locks, both IDT-BOF and IDT-BFO have a completely planar structure. IDT-BOF exhibits a similar LUMO to IDT-BFO, but higher HOMO energy levels, leading to a smaller optical bandgap and red-shifted absorption. However, IDT-BOF-based bulk-heterojunction organic solar cells (BHJ-OSCs) coupled with PBDB-T, and PCE-10 as donor materials both exhibited a lower PCE than that of IDT-BFO (PBDB-T: 5.2 vs. 6.1 %; PCE-10: 1.7 vs. 3.2 %). Comprehensively comparing and investigating IDT-BOF : PBDB-T and IDT-BFO : PBDB-T OSCs suggested that the large phase separation and serious charge recombination of IDT-BOF-based OSCs contributed to its lower power conversion efficiency. Importantly, ternary solar cells based on PBDB-T : Y5 as control devices with an additional 10 % IDT-BFO exhibited a 5 % enhancement in the PCE compared to the control device (14.3 vs. 13.46 %).
Collapse
Affiliation(s)
- Jianglin Wu
- Key Laboratory of Green Chemistry and Technology (Ministry of Education) College of Chemistry, Sichuan University, Chengdu, 610064, P. R. China
- SINOPEC Maoming Petrochemical Co., Ltd, Maoming, 525000, P. R. China
- Guangdong Provincial Key Laboratory of Advanced Green Lubricating Materials, Maoming, 525000, P. R. China
| | - Caixia Fu
- Key Laboratory of Green Chemistry and Technology (Ministry of Education) College of Chemistry, Sichuan University, Chengdu, 610064, P. R. China
- SINOPEC Maoming Petrochemical Co., Ltd, Maoming, 525000, P. R. China
- Guangdong Provincial Key Laboratory of Advanced Green Lubricating Materials, Maoming, 525000, P. R. China
| | - Baiquan Chen
- Key Laboratory of Green Chemistry and Technology (Ministry of Education) College of Chemistry, Sichuan University, Chengdu, 610064, P. R. China
| | - Xugang Rong
- Key Laboratory of Green Chemistry and Technology (Ministry of Education) College of Chemistry, Sichuan University, Chengdu, 610064, P. R. China
| | - Zhiyun Lu
- Key Laboratory of Green Chemistry and Technology (Ministry of Education) College of Chemistry, Sichuan University, Chengdu, 610064, P. R. China
| | - Yan Huang
- Key Laboratory of Green Chemistry and Technology (Ministry of Education) College of Chemistry, Sichuan University, Chengdu, 610064, P. R. China
| |
Collapse
|
5
|
Tan X, Jian J, Zheng X, Zhao J, Huang J. Improving Photovoltaic Performance of All-Polymer Solar Cells by Adding an Amorphous B←N Embedded Polymer as the Third Component. Macromol Rapid Commun 2023; 44:e2300375. [PMID: 37579197 DOI: 10.1002/marc.202300375] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/26/2023] [Revised: 07/23/2023] [Indexed: 08/16/2023]
Abstract
Currently, most of the disclosed ternary strategies to improve photovoltaic performance of all-polymer solar cells (all-PSCs) commonly focus on the guest polymers having similar structures with the host polymer donors or acceptors. Herein, this work develops a distinctive ternary method that adding an amorphous B←N embedded polymer named BN-Cl-2fT to a crystallized host polymer blend of PM6 (a commercialized polymer donor) and PY-TT (a copolymer of Y6 and thieno[3,2-b]thiophene). Although the structures between BN-Cl-2fT and PM6 and PY-TT are completely different, excellent miscibility is found between BN-Cl-2fT and both of the host PM6 and PY-TT, which can be interpreted by the crowded phenyl groups anchoring along the backbone of BN-Cl-2fT, leading to weak self-aggregation. Glazing incidence wide-angle X-ray diffraction (GIWAXS) measurements explicitly confirm the crystallization of PM6 and PY-TT and amorphous feature of BN-Cl-2fT. Furthermore, adding 10 wt% BN-Cl-2fT to PM6:PY-TT can significantly enhance the crystallization of the host polymers. Thus the ternary devices based on PM6:PY-TT:BN-Cl-2fT afford promote short-circuit current density (JSC , 23.29 vs. 21.80 mA cm-2 ), fill factor (FF, 62.4% vs. 60.0%), and power conversion efficiency (PCE, 13.70% vs. 12.23%) in contrast to these parameters of binary devices based on PM6:PY-TT. This work provides a unique and enlightening avenue to design high performance all-PSCs by adding amorphous B←N embedded polymers as guest component to enhance host-crystallization.
Collapse
Affiliation(s)
- Xueyan Tan
- College of Materials Science and Engineering, Huaqiao University, Xiamen, 361021, China
| | - Junyang Jian
- College of Materials Science and Engineering, Huaqiao University, Xiamen, 361021, China
| | - Xueqiong Zheng
- College of Materials Science and Engineering, Huaqiao University, Xiamen, 361021, China
| | - Jinying Zhao
- College of Materials Science and Engineering, Huaqiao University, Xiamen, 361021, China
| | - Jianhua Huang
- College of Materials Science and Engineering, Huaqiao University, Xiamen, 361021, China
| |
Collapse
|
6
|
Ma S, Li B, Gong S, Wang J, Liu B, Young Jeong S, Chen X, Young Woo H, Feng K, Guo X. Biselenophene Imide: Enabling Polymer Acceptor with High Electron Mobility for High-Performance All-Polymer Solar Cells. Angew Chem Int Ed Engl 2023; 62:e202308306. [PMID: 37461155 DOI: 10.1002/anie.202308306] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/13/2023] [Accepted: 07/17/2023] [Indexed: 07/29/2023]
Abstract
The shortage of narrow band gap polymer acceptors with high electron mobility is the major bottleneck for developing efficient all-polymer solar cells (all-PSCs). Herein, we synthesize a distannylated electron-deficient biselenophene imide monomer (BSeI-Tin) with high purity/reactivity, affording an excellent chance to access acceptor-acceptor (A-A) type polymer acceptors. Copolymerizing BSeI-Tin with dibrominated monomer Y5-Br, the resulting A-A polymer PY5-BSeI shows a higher molecular weight, narrower band gap, deeper-lying frontier molecular orbital levels and larger electron mobility than the donor-acceptor type counterpart PY5-BSe. Consequently, the PY5-BSeI-based all-PSCs deliver a remarkable efficiency of 17.77 % with a high short-circuit current of 24.93 mA cm-2 and fill factor of 75.83 %. This efficiency is much higher than that (10.70 %) of the PY5-BSe-based devices. Our study demonstrates that BSeI is a promising building block for constructing high-performance polymer acceptors and stannylation of electron-deficient building blocks offers an excellent approach to developing A-A type polymers for all-PSCs and even beyond.
Collapse
Affiliation(s)
- Suxiang Ma
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China
| | - Bangbang Li
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China
| | - Shaokuan Gong
- Department of Mechanical and Energy Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China
| | - Junwei Wang
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China
| | - Bin Liu
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China
| | - Sang Young Jeong
- Department of Chemistry, Korea University, Seoul, 136-713, South Korea
| | - Xihan Chen
- Department of Mechanical and Energy Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China
| | - Han Young Woo
- Department of Chemistry, Korea University, Seoul, 136-713, South Korea
| | - Kui Feng
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China
- Academy for Advanced Interdisciplinary Studies, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China
| | - Xugang Guo
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong 518055, China
- Songshan Lake Materials Laboratory, Dongguan, Guangdong 523808, China
| |
Collapse
|
7
|
Li J, Chen Z, Wang J, Young Jeong S, Yang K, Feng K, Yang J, Liu B, Woo HY, Guo X. Semiconducting Polymers Based on Simple Electron-Deficient Cyanated trans-1,3-Butadienes for Organic Field-Effect Transistors. Angew Chem Int Ed Engl 2023; 62:e202307647. [PMID: 37525009 DOI: 10.1002/anie.202307647] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/31/2023] [Revised: 07/31/2023] [Accepted: 07/31/2023] [Indexed: 08/02/2023]
Abstract
Developing high-performance but low-cost n-type polymers remains a significant challenge in the commercialization of organic field-effect transistors (OFETs). To achieve this objective, it is essential to design the key electron-deficient units with simple structures and facile preparation processes, which can facilitate the production of low-cost n-type polymers. Herein, by sequentially introducing fluorine and cyano functionalities onto trans-1,3-butadiene, we developed a series of structurally simple but highly electron-deficient building blocks, namely 1,4-dicyano-butadiene (CNDE), 3-fluoro-1,4-dicyano-butadiene (CNFDE), and 2,3-difluoro-1,4-dicyano-butadiene (CNDFDE), featuring a highly coplanar backbone and deep-positioned lowest unoccupied molecular orbital (LUMO) energy levels (-3.03-4.33 eV), which render them highly attractive for developing n-type semiconducting polymers. Notably, all these electron-deficient units can be easily accessed by a two-step high-yield synthetic procedure from low-cost raw materials, thus rendering them highly promising candidates for commercial applications. Upon polymerization with diketopyrrolopyrrole (DPP), three copolymers were developed that demonstrated unipolar n-type transport characteristics in OFETs with the highest electron mobility of >1 cm2 V-1 s-1 . Hence, CNDE, CNFDE, and CNDFDE represent a class of novel, simple, and efficient electron-deficient units for constructing low-cost n-type polymers, thereby providing valuable insight for OFET applications.
Collapse
Affiliation(s)
- Jianfeng Li
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), 518055, Shenzhen, Guangdong, China
| | - Zhicai Chen
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), 518055, Shenzhen, Guangdong, China
- Department State Key Laboratory of Marine Resource Utilization in South China Sea, College of Materials Science and Engineering, Hainan University, 570228, Haikou, Hainan, China
| | - Junwei Wang
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), 518055, Shenzhen, Guangdong, China
| | - Sang Young Jeong
- Research Institute for Natural Sciences, Department of Chemistry, Korea University, 02841, Seoul, South Korea
| | - Kun Yang
- State Key Laboratory of Chemo/Biosensing and Chemometrics, College of Chemistry and Chemical Engineering, Hunan University, 410082, Changsha, Hunan, China
| | - Kui Feng
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), 518055, Shenzhen, Guangdong, China
| | - Jie Yang
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), 518055, Shenzhen, Guangdong, China
| | - Bin Liu
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), 518055, Shenzhen, Guangdong, China
| | - Han Young Woo
- Research Institute for Natural Sciences, Department of Chemistry, Korea University, 02841, Seoul, South Korea
| | - Xugang Guo
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), 518055, Shenzhen, Guangdong, China
- Songshan Lake Materials Laboratory, 523808, Dongguan, Guangdong, China
| |
Collapse
|
8
|
Zhou Z, Xu Y, Yang J, Zhang S, Jin S, Li H, Zhu W, Liu Y. New Medium-Bandgap Nonfused Ring Guest Acceptor with a Higher-Lying LUMO Level Enables High-Performance Ternary Organic Solar Cells. ACS APPLIED MATERIALS & INTERFACES 2023; 15:42792-42801. [PMID: 37650699 DOI: 10.1021/acsami.3c06529] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 09/01/2023]
Abstract
Adding another constituent into a binary system, known as a ternary strategy, represents a simple and effective approach to boosting the power conversion efficiency (PCE) of organic solar cells (OSCs). Herein, we have prepared a new nonfused ring small-molecule acceptor with a medium bandgap, named DFTQA-2FIC, which possesses a high-lying lowest unoccupied molecular orbital energy level and a strong intramolecular charge-transfer effect. We elaborately utilized it as a third component in a typical PM6:Y6 blend to obtain high-performance ternary OSCs. The resulting ternary blend film exhibited superior and balanced hole/electron mobility, enhanced favorable aggregation morphology, and reduced charge carrier recombination. Consequently, an optimized ternary OSC presented a distinctly increased PCE of 17.29%, accompanied by synchronous enhancements in crucial parameters, representing a 7.46% improvement over the binary OSC based on PM6:Y6 with a PCE of 16.09%. This study highlights that incorporating DFTQA-2FIC as a third component in a binary system is suitable for optimizing photovoltaic performance.
Collapse
Affiliation(s)
- Zhongxin Zhou
- School of Materials Science and Engineering, Jiangsu Engineering Laboratory of Light-Electricity-Heat Energy-Converting Materials and Applications, Changzhou University, Changzhou 213164, China
| | - Yongchuan Xu
- School of Materials Science and Engineering, Jiangsu Engineering Laboratory of Light-Electricity-Heat Energy-Converting Materials and Applications, Changzhou University, Changzhou 213164, China
| | - Jun Yang
- School of Materials Science and Engineering, Jiangsu Engineering Laboratory of Light-Electricity-Heat Energy-Converting Materials and Applications, Changzhou University, Changzhou 213164, China
| | - Shiyue Zhang
- School of Materials Science and Engineering, Jiangsu Engineering Laboratory of Light-Electricity-Heat Energy-Converting Materials and Applications, Changzhou University, Changzhou 213164, China
| | - Shujing Jin
- School of Materials Science and Engineering, Jiangsu Engineering Laboratory of Light-Electricity-Heat Energy-Converting Materials and Applications, Changzhou University, Changzhou 213164, China
| | - Hongxiang Li
- College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu 610065, China
| | - WeiGuo Zhu
- School of Materials Science and Engineering, Jiangsu Engineering Laboratory of Light-Electricity-Heat Energy-Converting Materials and Applications, Changzhou University, Changzhou 213164, China
| | - Yu Liu
- School of Materials Science and Engineering, Jiangsu Engineering Laboratory of Light-Electricity-Heat Energy-Converting Materials and Applications, Changzhou University, Changzhou 213164, China
| |
Collapse
|
9
|
Wang Y, Meng B, Liu J, Zhu F, Qin C, Liu J, Wang L. A cyano-based electron-accepting building block to design n-type conjugated polymers with absorption wavelength of >1000 nm. Chem Commun (Camb) 2023; 59:1513-1516. [PMID: 36656573 DOI: 10.1039/d2cc06626b] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/15/2023]
Abstract
There are much fewer n-type conjugated polymers than p-type counterparts because of the lack of strong electron-accepting building blocks. We report a novel strong electron-accepting unit based on a dicyanomethylene unit. The resulting polymers exhibit LUMO energy levels of as low as -4.04 eV and narrow optical gaps with an onset absorption wavelength of 1050 nm. Moreover, the polymers exhibit near-infrared light absorption with good photostability because of their low-lying LUMO/HOMO energy levels.
Collapse
Affiliation(s)
- Yinghui Wang
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, People's Republic of China. .,University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui 230026, China
| | - Bin Meng
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, People's Republic of China.
| | - Jian Liu
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, People's Republic of China. .,University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui 230026, China
| | - Feng Zhu
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, People's Republic of China. .,University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui 230026, China
| | - Chuanjiang Qin
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, People's Republic of China. .,University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui 230026, China
| | - Jun Liu
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, People's Republic of China. .,University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui 230026, China
| | - Lixiang Wang
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, People's Republic of China. .,University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui 230026, China
| |
Collapse
|
10
|
Wang J, Feng K, Jeong SY, Liu B, Wang Y, Wu W, Hou Y, Woo HY, Guo X. Acceptor-acceptor type polymers based on cyano-substituted benzochalcogenadiazole and diketopyrrolopyrrole for high-efficiency n-type organic thermoelectrics. Polym J 2022. [DOI: 10.1038/s41428-022-00717-w] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/09/2022]
|
11
|
Shen X, Lai X, Lai H, Zhao T, Zhu Y, Pu M, Wang H, Tan P, He F. Isomerism Strategy to Optimize Aggregation and Morphology for Superior Polymer Solar Cells. Macromolecules 2022. [DOI: 10.1021/acs.macromol.2c00837] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/29/2022]
Affiliation(s)
- Xiangyu Shen
- Shenzhen Grubbs Institute and Department of Chemistry, Southern University of Science and Technology, Shenzhen 518055, China
| | - Xue Lai
- Shenzhen Grubbs Institute and Department of Chemistry, Southern University of Science and Technology, Shenzhen 518055, China
- School of Chemistry and Chemical Engineering, Harbin Institute of Technology, Harbin 150001, China
| | - Hanjian Lai
- Shenzhen Grubbs Institute and Department of Chemistry, Southern University of Science and Technology, Shenzhen 518055, China
- School of Chemistry and Chemical Engineering, Harbin Institute of Technology, Harbin 150001, China
| | - Tingxing Zhao
- Shenzhen Grubbs Institute and Department of Chemistry, Southern University of Science and Technology, Shenzhen 518055, China
| | - Yulin Zhu
- Shenzhen Grubbs Institute and Department of Chemistry, Southern University of Science and Technology, Shenzhen 518055, China
- School of Chemistry and Chemical Engineering, Harbin Institute of Technology, Harbin 150001, China
| | - Mingrui Pu
- Shenzhen Grubbs Institute and Department of Chemistry, Southern University of Science and Technology, Shenzhen 518055, China
| | - Hengtao Wang
- Shenzhen Grubbs Institute and Department of Chemistry, Southern University of Science and Technology, Shenzhen 518055, China
| | - Pu Tan
- Shenzhen Grubbs Institute and Department of Chemistry, Southern University of Science and Technology, Shenzhen 518055, China
| | - Feng He
- Shenzhen Grubbs Institute and Department of Chemistry, Southern University of Science and Technology, Shenzhen 518055, China
- Guangdong Provincial Key Laboratory of Catalysis, Southern University of Science and Technology, Shenzhen 518055, China
| |
Collapse
|
12
|
Planarized Polymer Acceptor Featuring High Electron Mobility for Efficient All-Polymer Solar Cells. CHINESE JOURNAL OF POLYMER SCIENCE 2022. [DOI: 10.1007/s10118-022-2767-4] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/03/2022]
|
13
|
Zhang YZ, Wang N, Wang YH, Miao JH, Liu J, Wang LX. 15% Efficiency All-Polymer Solar Cells Based on a Polymer Acceptor Containing B←N Unit. CHINESE JOURNAL OF POLYMER SCIENCE 2022. [DOI: 10.1007/s10118-022-2790-5] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/03/2022]
|
14
|
Ma S, Zhang H, Feng K, Guo X. Polymer Acceptors for High-Performance All-Polymer Solar Cells. Chemistry 2022; 28:e202200222. [PMID: 35266214 DOI: 10.1002/chem.202200222] [Citation(s) in RCA: 9] [Impact Index Per Article: 4.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/28/2022] [Indexed: 11/11/2022]
Abstract
All-polymer solar cells (all-PSCs) have attracted considerable attention owing to their pronounced advantages of excellent mechanical flexibility/stretchability and greatly enhanced device stability as compared to other types of organic solar cells (OSCs). Thanks to the extensive research efforts dedicated to the development of polymer acceptors, all-PSCs have achieved remarkable improvement of photovoltaic performance, recently. This review summarizes the recent progress of polymer acceptors based on the key electron-deficient building blocks, which include bithiophene imide (BTI) derivatives, boron-nitrogen coordination bond (B←N)-incorporated (hetero)arenes, cyano-functionalized (hetero)arenes, and fused-ring electron acceptors (FREAs). In addition, single-component-based all-PSCs are also briefly discussed. The structure-property correlations of polymer acceptors are elaborated in detail. Finally, we offer our insights into the development of new electron-deficient building blocks with further optimized properties and the polymers built from them for efficient all-PSCs.
Collapse
Affiliation(s)
- Suxiang Ma
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong, 518055, P. R. China
| | - Hao Zhang
- Department of Chemistry, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong, 518055, P. R. China
| | - Kui Feng
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong, 518055, P. R. China.,Academy for Advanced Interdisciplinary Studies, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong, 518055, P. R. China
| | - Xugang Guo
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong, 518055, P. R. China.,Songshan Lake Materials Laboratory, Dongguan, Guangdong, 523808, P. R. China.,Guangdong Provincial Key Laboratory of Functional Oxide Materials and Devices, Southern University of Science and Technology (SUSTech), Shenzhen, Guangdong, 518055, P. R. China
| |
Collapse
|
15
|
Wang T, Sun R, Yang XR, Wu Y, Wang W, Li Q, Zhang CF, Min J. A Near-Infrared Polymer Acceptor Enables over 15% Efficiency for All-Polymer Solar Cells. CHINESE JOURNAL OF POLYMER SCIENCE 2022. [DOI: 10.1007/s10118-022-2697-1] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/30/2022]
|
16
|
Gokulnath T, Feng K, Park HY, Do Y, Park H, Gayathri RD, Reddy SS, Kim J, Guo X, Yoon J, Jin SH. Facile Strategy for Third Component Optimization in Wide-Band-Gap π-Conjugated Polymer Donor-Based Efficient Ternary All-Polymer Solar Cells. ACS APPLIED MATERIALS & INTERFACES 2022; 14:11211-11221. [PMID: 35225595 DOI: 10.1021/acsami.1c20542] [Citation(s) in RCA: 4] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/14/2023]
Abstract
Emerging organic solar cells based on a ternary strategy is one of the most effective methods for improving the blend film morphology, absorption ability, and device performances. On the other hand, this strategy has had very limited success in all-polymer solar cells (all-PSCs) because of the scarcity of new polymers and the challenges faced during third component optimization. Herein, highly efficient ternary all-PSCs were developed from siloxane-functionalized side chains with a wide-band-gap (Eg) polymer, Si-BDT, which is blended with a medium and ultra-narrow Eg polymer donor and acceptor, PTB7-Th, and DCNBT-TPIC. An impressive power conversion efficiency (PCE) of 13.45% was achieved in the ternary all-PSCs [PTB7-Th(0.6):Si-BDT(0.4):DCNBT-TPIC(0.6)] with the addition of 0.4 wt equivalent Si-BDT into binary all-PSCs [PTB7-Th(1):DCNBT-TPIC(0.6) PCE of 10.11%]. In contrast, the binary all-PSCs with a Si-BDT(1):DCNBT-TPIC(0.6) active layer only exhibited a good PCE of 9.92%. More importantly, the siloxane-functionalized side chains increase the light-absorption ability, carrier mobility, blend miscibility, and film morphology in ternary devices compared to those of the binary devices. Hence, exciton dissociation, charge carrier transport, and suppressed recombination properties were facilitated. In the presence of Si-BDT, both binary and ternary all-PSCs PCEs are significantly improved. Indeed, 13.45% PCE is one of the best values reported for all-PSCs except for those based on polymerized small molecule acceptors. In addition, the ternary all-PSCs showed excellent environmental and thermal stabilities with 95 and 84% of the initial PCE retained after 900 and 500 h, respectively. These results offer effective device engineering, providing a new avenue for improving the device performance in ternary all-PSCs.
Collapse
Affiliation(s)
- Thavamani Gokulnath
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busandaehakro 63-2, Busan 46241, Republic of Korea
| | - Kui Feng
- Department of Materials Science and Engineering, Southern University of Science and Technology,Shenzhen, Guangdong 518055, China
| | - Ho-Yeol Park
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busandaehakro 63-2, Busan 46241, Republic of Korea
| | - Yeongju Do
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busandaehakro 63-2, Busan 46241, Republic of Korea
| | - Hyungjin Park
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busandaehakro 63-2, Busan 46241, Republic of Korea
| | - Rajalapati Durga Gayathri
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busandaehakro 63-2, Busan 46241, Republic of Korea
| | - Saripally Sudhaker Reddy
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busandaehakro 63-2, Busan 46241, Republic of Korea
- Department of Chemical & Biological Engineering, Monash University, Clayton, Victoria 3800, Australia
| | - Jehan Kim
- Beamline Division, Pohang Accelerator Laboratory, Pohang University of Science and Technology, Pohang 37673, Republic of Korea
| | - Xugang Guo
- Department of Materials Science and Engineering, Southern University of Science and Technology,Shenzhen, Guangdong 518055, China
| | - Jinhwan Yoon
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busandaehakro 63-2, Busan 46241, Republic of Korea
| | - Sung-Ho Jin
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busandaehakro 63-2, Busan 46241, Republic of Korea
| |
Collapse
|
17
|
Incorporating Se atoms to organoboron polymer electron acceptors to tune opto-electronic properties. POLYMER 2022. [DOI: 10.1016/j.polymer.2022.124547] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/22/2023]
|
18
|
|
19
|
Xiong Y, Ye L, Zhang C. Eco‐friendly solution processing of all‐polymer solar cells: Recent advances and future perspective. JOURNAL OF POLYMER SCIENCE 2021. [DOI: 10.1002/pol.20210745] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/15/2023]
Affiliation(s)
- Yuan Xiong
- Science and Technology on Power Sources Laboratory Tianjin Institute of Power Sources, China Electronics Technology Group Corporation (CETC) Tianjin China
| | - Long Ye
- State Key Laboratory of Applied Optics, Changchun Institute of Optics, Fine Mechanics and Physics Chinese Academy of Sciences Changchun China
- School of Materials Science and Engineering Tianjin Key Laboratory of Molecular Optoelectronic Sciences, Tianjin University Tianjin China
| | - Chao Zhang
- Science and Technology on Power Sources Laboratory Tianjin Institute of Power Sources, China Electronics Technology Group Corporation (CETC) Tianjin China
| |
Collapse
|
20
|
Miao J, Wang Y, Liu J, Wang L. Organoboron molecules and polymers for organic solar cell applications. Chem Soc Rev 2021; 51:153-187. [PMID: 34851333 DOI: 10.1039/d1cs00974e] [Citation(s) in RCA: 44] [Impact Index Per Article: 14.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/15/2023]
Abstract
Organic solar cells (OSCs) are emerging as a new photovoltaic technology with the great advantages of low cost, light-weight, flexibility and semi-transparency. They are promising for portable energy-conversion products and building-integrated photovoltaics. Organoboron chemistry offers an important toolbox to design novel organic/polymer optoelectronic materials and to tune their optoelectronic properties for OSC applications. At present, organoboron small molecules and polymers have become an important class of organic photovoltaic materials. Power conversion efficiencies (PCEs) of 16% and 14% have been realized with organoboron polymer electron donors and electron acceptors, respectively. In this review, we summarize the research progress in various kinds of organoboron photovoltaic materials for OSC applications, including organoboron small molecular electron donors, organoboron small molecular electron acceptors, organoboron polymer electron donors and organoboron polymer electron acceptors. This review also discusses how to tune their opto-electronic properties and active layer morphology for enhancing OSC device performance. We also offer our insight into the opportunities and challenges in improving the OSC device performance of organoboron photovoltaic materials.
Collapse
Affiliation(s)
- Junhui Miao
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, P. R. China.
| | - Yinghui Wang
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, P. R. China. .,University of Science and Technology of China, Hefei 230026, P. R. China
| | - Jun Liu
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, P. R. China.
| | - Lixiang Wang
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, P. R. China.
| |
Collapse
|
21
|
Zhang Y, Wang N, Wang Y, Zhang J, Liu J, Wang L. All-polymer indoor photovoltaic modules. iScience 2021; 24:103104. [PMID: 34611609 PMCID: PMC8476653 DOI: 10.1016/j.isci.2021.103104] [Citation(s) in RCA: 7] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/29/2021] [Revised: 08/03/2021] [Accepted: 09/04/2021] [Indexed: 11/28/2022] Open
Abstract
Indoor photovoltaic (IPV) with power output over 100 μW is promising to power the numerous sensor nodes in the Internet of Things (IoT) ecosystem. All polymer photovoltaic has the advantages of excellent thermal stability and superior mechanical properties. In this work, we fabricate the first all-polymer indoor photovoltaic module with the active area of 10 cm2. The module uses polymer donor CD1 and new polymer acceptor PBN-21 with medium optical band gap of 1.9 eV as the active layer. It is processed with eco-friendly solvent tetrahydrofuran and the morphology can be improved by blade coating at 55°C. Under light emitting diode illumination at 1000 lux, the module exhibits a power conversion efficiency of 12.04% and a power output of 367.2 μW. The sufficient power output, high efficiency, excellent stability, and eco-friendly processing indicate that all-polymer indoor photovoltaic is a promising approach to achieve the self-powered of sensor nodes in the IoT ecosystem.
Collapse
Affiliation(s)
- Yingze Zhang
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, P. R. China
- University of Science and Technology of China, Hefei 230026, P. R. China
| | - Ning Wang
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, P. R. China
- University of Science and Technology of China, Hefei 230026, P. R. China
| | - Yinghui Wang
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, P. R. China
- University of Science and Technology of China, Hefei 230026, P. R. China
| | - Jidong Zhang
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, P. R. China
| | - Jun Liu
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, P. R. China
- University of Science and Technology of China, Hefei 230026, P. R. China
| | - Lixiang Wang
- State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022, P. R. China
- University of Science and Technology of China, Hefei 230026, P. R. China
| |
Collapse
|
22
|
Feng K, Guo H, Sun H, Guo X. n-Type Organic and Polymeric Semiconductors Based on Bithiophene Imide Derivatives. Acc Chem Res 2021; 54:3804-3817. [PMID: 34617720 DOI: 10.1021/acs.accounts.1c00381] [Citation(s) in RCA: 39] [Impact Index Per Article: 13.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/28/2023]
Abstract
ConspectusIn the last three decades, p-type (hole-transporting) organic and polymeric semiconductors have achieved great success in terms of materials diversity and device performance, while the development of n-type (electron-transporting) analogues greatly lags behind, which is limited by the scarcity of highly electron-deficient building blocks with compact geometry and good solubility. However, such n-type semiconductors are essential due to the existence of the p-n junction and a complementary metal oxide semiconductor (CMOS)-like circuit in organic electronic devices. Among various electron-deficient building blocks, imide-functionalized arenes, such as naphthalene diimide (NDI) and perylene diimide (PDI), have been proven to be the most promising ones for developing n-type organic and polymeric semiconductors. Nevertheless, phenyl-based NDI and PDI lead to sizable steric hindrance with neighboring (hetero)arenes and a high degree of backbone distortion in the resultant semiconductors, which greatly limits their microstructural ordering and charge transport. To attenuate the steric hindrance associated with NDI and PDI, a novel imide-functionalized heteroarene, bithiophene imide (BTI), was designed; however, the BTI-based semiconductors suffer from high-lying frontier molecular orbital (FMO) energy levels as a result of their electron-rich thiophene framework and monoimide group, which is detrimental to n-type performance.In this Account, we review a series of BTI derivatives developed via various strategies, including ring fusion, thiazole substitution, fluorination, cyanation, and chalcogen substitution, and elaborate the synthesis routes designed to overcome the synthesis challenges due to their high electron deficiency. After structural optimization, these BTI derivatives can not only retain the advantages of good solubility, a planar backbone, and small steric hindrance inherited from BTI but also have greatly suppressed FMO levels. These novel building blocks enable the construction of a great number of n-type organic and polymeric semiconductors, particularly acceptor-acceptor (or all-acceptor)-type polymers, with remarkable performance in various devices, including electron mobility (μe) of 3.71 cm2 V-1 s-1 in organic thin-film transistors (OTFTs), a power conversion efficiency (PCE) of 15.2% in all-polymer solar cells (all-PSCs), a PCE of 20.8% in inverted perovskite solar cells (PVSCs), electrical conductivity (σ) of 0.34 S cm-1 and a power factor (PF) of 1.52 μW m-1 K-2 in self-doped diradicals, and σ of 23.3 S cm-1 and a PF of ∼10 μW m-1 K-2 in molecularly n-doped polymers, all of which are among the best values in each type of device. The structure-property-device performance correlations of these n-type semiconductors are elucidated. The design strategy and synthesis of these novel BTI derivatives provide important information for developing highly electron-deficient building blocks with optimized physicochemical properties. Finally, we offer our insights into the further development of BTI derivatives and semiconductors built from them.
Collapse
Affiliation(s)
- Kui Feng
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong 518055, China
| | - Han Guo
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong 518055, China
| | - Huiliang Sun
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong 518055, China
| | - Xugang Guo
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong 518055, China
| |
Collapse
|
23
|
You H, Lee S, Kim D, Kang H, Lim C, Kim FS, Kim BJ. Effects of the Selective Alkoxy Side Chain Position in Quinoxaline-Based Polymer Acceptors on the Performance of All-Polymer Solar Cells. ACS APPLIED MATERIALS & INTERFACES 2021; 13:47817-47825. [PMID: 34590813 DOI: 10.1021/acsami.1c12288] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/13/2023]
Abstract
The effects of the position of alkoxy side chains in quinoxaline (Qx)-based polymer acceptors (PAs) on the characteristics of materials and the device parameters of all-polymer solar cells (all-PSCs) are investigated. The alkoxy side chains are selectively located at the meta, para, and both positions in pendant benzenes of Qx units, constructing PAs denoted as P(QxCN-T2)-m, P(QxCN-T2)-p, and P(QxCN-T2), respectively. Among them, P(QxCN-T2)-m exhibits the deepest energy levels owing to the enhanced electron-withdrawing effect of meta-positioned alkoxy chains, which is in contrast to P(QxCN-T2)-p where para-positioned alkoxy chains have an electron-donating property. In addition, the meta-positioned alkoxy chains induce good electron-conducting pathways, while the para-positioned ones significantly interrupt crystallization and intermolecular interactions between the conjugated backbones. Thus, when the PAs are applied to all-PSCs, a power conversion efficiency (PCE) of 5.07% is attained in the device using P(QxCN-T2)-m with efficient exciton dissociation and good electron-transporting ability. On the contrary, the P(QxCN-T2)-p-based counterpart has a PCE of only 1.62%. These results demonstrate that introducing alkoxy side chains at a proper location in the Qx-based PAs is crucial for their application to all-PSCs.
Collapse
Affiliation(s)
- Hoseon You
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea
| | - Seungjin Lee
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea
| | - Donguk Kim
- School of Chemical Engineering and Materials Science, Chung-Ang University (CAU), Seoul 06974, Republic of Korea
| | - Hyunbum Kang
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea
| | - Chulhee Lim
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea
| | - Felix Sunjoo Kim
- School of Chemical Engineering and Materials Science, Chung-Ang University (CAU), Seoul 06974, Republic of Korea
| | - Bumjoon J Kim
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 34141, Republic of Korea
| |
Collapse
|
24
|
Pan L, Zhan T, Oh J, Zhang Y, Tang H, Yang M, Li M, Yang C, Liu X, Cai P, Duan C, Huang F, Cao Y. N-Type Quinoidal Polymers Based on Dipyrrolopyrazinedione for Application in All-Polymer Solar Cells. Chemistry 2021; 27:13527-13533. [PMID: 34406681 DOI: 10.1002/chem.202102084] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/11/2021] [Indexed: 01/06/2023]
Abstract
Conjugated molecules and polymers with intrinsic quinoidal structure are promising n-type organic semiconductors, which have been reported for application in field-effect transistors and thermoelectric devices. In principle, the molecular and electronic characteristics of quinoidal polymers can also enable their application in organic solar cells. Herein, two quinoidal polymers, named PzDP-T and PzDP-ffT, based on dipyrrolopyrazinedione were synthesized and used as electron acceptors in all-polymer solar cells (all-PSCs). Both PzDP-T and PzDP-ffT showed suitable energy levels and wide light absorption range that extended to the near-infrared region. When combined with the polymer donor PBDB-T, the resulting all-PSCs based on PzDP-T and PzDP-ffT exhibited a power conversion efficiency (PCE) of 1.33 and 2.37 %, respectively. This is the first report on the application of intrinsic quinoidal conjugated polymers in all-PSCs. The photovoltaic performance of the all-PSCs was revealed to be mainly limited by the relatively poor and imbalanced charge transport, considerable charge recombination. Detailed investigations on the structure-performance relationship suggested that synergistic optimization of light absorption, energy levels, and charge transport properties is needed to achieve more successful application of intrinsic quinoidal conjugated polymers in all-PSCs.
Collapse
Affiliation(s)
- Langheng Pan
- Institute of Polymer Optoelectronic Materials and Devices, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou, 510640, P. R. China
| | - Tao Zhan
- Institute of Polymer Optoelectronic Materials and Devices, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou, 510640, P. R. China.,School of Materials Science and Engineering, Guilin University of Electronic Technology, Guilin, 541004, P. R. China
| | - Jiyeon Oh
- Department of Energy Engineering, School of Energy and Chemical Engineering, Perovtronics Research Center, Low Dimensional Carbon Materials Center, Ulsan National Institute of Science and Technology (UNIST), Ulsan, 44919, South Korea
| | - Yue Zhang
- Institute of Polymer Optoelectronic Materials and Devices, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou, 510640, P. R. China
| | - Haoran Tang
- Institute of Polymer Optoelectronic Materials and Devices, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou, 510640, P. R. China
| | - Mingqun Yang
- Institute of Polymer Optoelectronic Materials and Devices, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou, 510640, P. R. China
| | - Mengmeng Li
- Key Laboratory of Microelectronic Devices and Integrated Technology, Institute of Microelectronics, Chinese Academy of Science, Beijing, 100029, P. R. China
| | - Changduk Yang
- Department of Energy Engineering, School of Energy and Chemical Engineering, Perovtronics Research Center, Low Dimensional Carbon Materials Center, Ulsan National Institute of Science and Technology (UNIST), Ulsan, 44919, South Korea
| | - Xi Liu
- Guangdong-Hong Kong Joint Laboratory for New Textile Materials, School of Textile Materials and Engineering, Wuyi University, Jiangmen, 529020, P. R. China
| | - Ping Cai
- School of Materials Science and Engineering, Guilin University of Electronic Technology, Guilin, 541004, P. R. China
| | - Chunhui Duan
- Institute of Polymer Optoelectronic Materials and Devices, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou, 510640, P. R. China.,State Key Laboratory of Fine Chemicals, Dalian University of Technology, Dalian, 116024, P. R. China
| | - Fei Huang
- Institute of Polymer Optoelectronic Materials and Devices, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou, 510640, P. R. China
| | - Yong Cao
- Institute of Polymer Optoelectronic Materials and Devices, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou, 510640, P. R. China
| |
Collapse
|
25
|
You H, Kang H, Kim D, Park JS, Lee JW, Lee S, Kim FS, Kim BJ. Cyano-Functionalized Quinoxaline-Based Polymer Acceptors for All-Polymer Solar Cells and Organic Transistors. CHEMSUSCHEM 2021; 14:3520-3527. [PMID: 33655716 DOI: 10.1002/cssc.202100080] [Citation(s) in RCA: 6] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/12/2021] [Revised: 02/05/2021] [Indexed: 06/12/2023]
Abstract
Quinoxaline (Qx) derivatives are promising building units for efficient photovoltaic polymers owing to their strong light absorption and high charge-transport abilities, but they have been used exclusively in the construction of polymer donors. Herein, for the first time, Qx-based polymer acceptors (PA s) were developed by introducing electron-withdrawing cyano (CN) groups into the Qx moiety (QxCN). A series of QxCN-based PA s, P(QxCN-T2), P(QxCN-TVT), and P(QxCN-T3), were synthesized by copolymerizing the QxCN unit with bithiophene, (E)-1,2-di(thiophene-2-yl)ethene, and terthiophene, respectively. All of the PA s exhibited unipolar n-type characteristics with organic field-effect transistor (OFET) mobilities of around 10-2 cm2 V-1 s-1 . In space-charge-limited current devices, P(QxCN-T2) and P(QxCN-TVT) exhibited electron mobilities greater than 1.0×10-4 cm2 V-1 s-1 , due to the well-ordered structure with tight π-π stacking. When the PA s were applied in all-polymer solar cells (all-PSCs), the highest performance of 5.32 % was achieved in the P(QxCN-T2)-based device. These results demonstrate the significant potential of Qx-based PA s for high-performance all-PSCs and OFETs.
Collapse
Affiliation(s)
- Hoseon You
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, 34141, Republic of Korea
| | - Hyunbum Kang
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, 34141, Republic of Korea
| | - Donguk Kim
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, 34141, Republic of Korea
| | - Jin Su Park
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, 34141, Republic of Korea
| | - Jin-Woo Lee
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, 34141, Republic of Korea
| | - Seungjin Lee
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, 34141, Republic of Korea
| | - Felix Sunjoo Kim
- School of Chemical Engineering and Materials Science, Chung-Ang University (CAU), Seoul, 06974, Republic of Korea
| | - Bumjoon J Kim
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, 34141, Republic of Korea
| |
Collapse
|
26
|
Li Z, Feng K, Wang J, Li M, Xu Q, Li X, Guo X. Highly Efficient All-Polymer Solar Cells Processed from Nonhalogenated Solvents. CHEMSUSCHEM 2021; 14:3553-3560. [PMID: 33913608 DOI: 10.1002/cssc.202100674] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/01/2021] [Revised: 04/26/2021] [Indexed: 06/12/2023]
Abstract
The remarkable advance of all-polymer solar cells (all-PSCs) achieved in the past decades is primarily powered by the innovation of polymer acceptors. However, most of high-performance all-PSCs are dominantly fabricated with halogenated solvents, which are detrimental to human bodies and the environment. Herein, eco-friendly solvent-processed all-PSCs were developed, based on wide-bandgap polymer poly[4,8-bis(5-(2-ethylhexylthio)thiophen-2-yl)-benzo-[1,2-b;4,5-b']dithiophene-alt-2,5-di(butyloctylthiophen-2-yl) -thiazolo[5,4-d]thiazole] (PSTZ) as donor and newly synthesized narrow-bandgap polymer 5,6-dicyano-2,1,3-benzothiadiazole indacenodithiophene (DCNBT-IDT) as acceptor. When processed with o-xylene and THF, PSTZ : DCNBT-IDT-based all-PSCs yielded remarkable power conversion efficiencies of 7.23 and 8.77 % with high short-circuit currents of 12.94 and 14.12 mA cm-2 , respectively. The results indicated that the utilization of an all-polymer blend based on narrow polymer acceptor and compatible polymer donor is an effective strategy for advancing eco-friendly solvent-processed all-PSCs.
Collapse
Affiliation(s)
- Zuojia Li
- Jiangxi Province Key Laboratory of Polymer Micro/Nano Manufacturing and Devices, School of Chemistry, Biology and Materials Science, East China University of Technology, Nanchang, Jiangxi, 330013, P. R. China
| | - Kui Feng
- Department of Materials Science and Engineering, Southern University of Science and Technology, Shenzhen, Guangdong, 518055, P. R. China
| | - Jingwei Wang
- Jiangxi Province Key Laboratory of Polymer Micro/Nano Manufacturing and Devices, School of Chemistry, Biology and Materials Science, East China University of Technology, Nanchang, Jiangxi, 330013, P. R. China
| | - Min Li
- Jiangxi Province Key Laboratory of Polymer Micro/Nano Manufacturing and Devices, School of Chemistry, Biology and Materials Science, East China University of Technology, Nanchang, Jiangxi, 330013, P. R. China
| | - Qianqian Xu
- Jiangxi Province Key Laboratory of Polymer Micro/Nano Manufacturing and Devices, School of Chemistry, Biology and Materials Science, East China University of Technology, Nanchang, Jiangxi, 330013, P. R. China
| | - Xiaochang Li
- GuanMat Optoelectronic Materials, Inc, Nanchang, Jiangxi, 330013, P. R. China
| | - Xugang Guo
- Department of Materials Science and Engineering, Southern University of Science and Technology, Shenzhen, Guangdong, 518055, P. R. China
| |
Collapse
|
27
|
Gokulnath T, Choi J, Jin H, Park HY, Sung K, Do Y, Park H, Reddy SS, Kim J, Song M, Yoon J, Jin SH. All-Polymer Solar Cells Approaching 12% Efficiency with a New π-Conjugated Polymer Donor Enabled by a Nonhalogenated Solvent Process. ACS APPLIED MATERIALS & INTERFACES 2021; 13:28231-28241. [PMID: 34101428 DOI: 10.1021/acsami.1c05921] [Citation(s) in RCA: 10] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/12/2023]
Abstract
High efficiency and nonhalogenated solvent processing are important issues for commercial application of all-polymer solar cells (all-PSCs). In this regard, we increased the photovoltaic performance of all-PSCs to a benchmark power conversion efficiency (PCE) of 11.66% by manipulating the pre-aggregation of a new π-conjugated polymer donor (Nap-SiBTz) using toluene as a solvent. This use of Nap-SiBTz enhanced the absorption coefficient (λmax = 9.30 × 104 cm-1), increased charge carrier mobility, suppressed trap-assisted recombination, improved bulk heterojunction morphology, and resulted in high PCEs of all-PSCs with an active layer thickness of 200 nm. To overcome severe charge recombination and energy losses, a 1-phenylnapthalene additive was used to achieve a well-ordered microstructure and molecular packing that inherently improved the device performances. The resulting encapsulation-free devices exhibited good ambient and thermal stabilities. The results of this study augur well for the future of the roll-to-roll production of all-PSCs.
Collapse
Affiliation(s)
- Thavamani Gokulnath
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busan 46241, Republic of Korea
| | - Jungmin Choi
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busan 46241, Republic of Korea
| | - Hyunjung Jin
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busan 46241, Republic of Korea
| | - Ho-Yeol Park
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busan 46241, Republic of Korea
| | - Kyungmin Sung
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busan 46241, Republic of Korea
| | - Yeongju Do
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busan 46241, Republic of Korea
| | - Hyungjin Park
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busan 46241, Republic of Korea
| | - Saripally Sudhaker Reddy
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busan 46241, Republic of Korea
- Department of Chemical Engineering, Monash University, Clayton, Victoria 3800, Australia
| | - Jehan Kim
- Beamline Division, Pohang Accelerator Laboratory, Pohang University of Science and Technology, Pohang, 37673 Republic of Korea
| | - Myungkwan Song
- Materials Center for Energy Convergence, Surface Technology Division, Korea Institute of Materials Science (KIMS), Gyeongnam 51508, Republic of Korea
| | - Jinhwan Yoon
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busan 46241, Republic of Korea
| | - Sung-Ho Jin
- Department of Chemistry Education, Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center (ERC), Pusan National University, Busan 46241, Republic of Korea
| |
Collapse
|
28
|
High-performance all-polymer solar cells enabled by a novel low bandgap non-fully conjugated polymer acceptor. Sci China Chem 2021. [DOI: 10.1007/s11426-021-1020-7] [Citation(s) in RCA: 24] [Impact Index Per Article: 8.0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/21/2022]
|
29
|
Feng K, Guo H, Wang J, Shi Y, Wu Z, Su M, Zhang X, Son JH, Woo HY, Guo X. Cyano-Functionalized Bithiophene Imide-Based n-Type Polymer Semiconductors: Synthesis, Structure-Property Correlations, and Thermoelectric Performance. J Am Chem Soc 2021; 143:1539-1552. [PMID: 33445867 DOI: 10.1021/jacs.0c11608] [Citation(s) in RCA: 57] [Impact Index Per Article: 19.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/07/2023]
Abstract
n-Type polymers with deep-positioned lowest unoccupied molecular orbital (LUMO) energy levels are essential for enabling n-type organic thin-film transistors (OTFTs) with high stability and n-type organic thermoelectrics (OTEs) with high doping efficiency and promising thermoelectric performance. Bithiophene imide (BTI) and its derivatives have been demonstrated as promising acceptor units for constructing high-performance n-type polymers. However, the electron-rich thiophene moiety in BTI leads to elevated LUMOs for the resultant polymers and hence limits their n-type performance and intrinsic stability. Herein, we addressed this issue by introducing strong electron-withdrawing cyano functionality on BTI and its derivatives. We have successfully overcome the synthetic challenges and developed a series of novel acceptor building blocks, CNI, CNTI, and CNDTI, which show substantially higher electron deficiencies than does BTI. On the basis of these novel building blocks, acceptor-acceptor type homopolymers and copolymers were successfully synthesized and featured greatly suppressed LUMOs (-3.64 to -4.11 eV) versus that (-3.48 eV) of the control polymer PBTI. Their deep-positioned LUMOs resulted in improved stability in OTFTs and more efficient n-doping in OTEs for the corresponding polymers with a highest electrical conductivity of 23.3 S cm-1 and a power factor of ∼10 μW m-1 K-2. The conductivity and power factor are among the highest values reported for solution-processed molecularly n-doped polymers. The new CNI, CNTI, and CNDTI offer a remarkable platform for constructing n-type polymers, and this study demonstrates that cyano-functionalization of BTI is a very effective strategy for developing polymers with deep-lying LUMOs for high-performance n-type organic electronic devices.
Collapse
Affiliation(s)
- Kui Feng
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong 518055, China
| | - Han Guo
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong 518055, China
| | - Junwei Wang
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong 518055, China
| | - Yongqiang Shi
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong 518055, China
| | - Ziang Wu
- Department of Chemistry, Korea University, 145 Anam-Ro, Seongbuk-Gu, Seoul 02841, South Korea
| | - Mengyao Su
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong 518055, China
| | - Xianhe Zhang
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong 518055, China
| | - Jae Hoon Son
- Department of Chemistry, Korea University, 145 Anam-Ro, Seongbuk-Gu, Seoul 02841, South Korea
| | - Han Young Woo
- Department of Chemistry, Korea University, 145 Anam-Ro, Seongbuk-Gu, Seoul 02841, South Korea
| | - Xugang Guo
- Department of Materials Science and Engineering, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong 518055, China
| |
Collapse
|
30
|
Benzothiadiazole-based Conjugated Polymers for Organic Solar Cells. CHINESE JOURNAL OF POLYMER SCIENCE 2021. [DOI: 10.1007/s10118-021-2537-8] [Citation(s) in RCA: 23] [Impact Index Per Article: 7.7] [Reference Citation Analysis] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/25/2022]
|
31
|
Zhang Z, Li Y. Polymerized Small‐Molecule Acceptors for High‐Performance All‐Polymer Solar Cells. Angew Chem Int Ed Engl 2020; 60:4422-4433. [DOI: 10.1002/anie.202009666] [Citation(s) in RCA: 161] [Impact Index Per Article: 40.3] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/13/2020] [Indexed: 11/06/2022]
Affiliation(s)
- Zhi‐Guo Zhang
- State Key Laboratory of Chemical Resource Engineering Beijing Advanced Innovation Center for Soft Matter Science and Engineering Beijing University of Chemical Technology Beijing 100029 China
| | - Yongfang Li
- Beijing National Laboratory for Molecular Sciences CAS Key Laboratory of Organic Solids Institute of Chemistry Chinese Academy of Sciences Beijing 100190 China
- Laboratory of Advanced Optoelectronic Materials College of Chemistry, Chemical Engineering and Materials Science Soochow University Suzhou Jiangsu 215123 China
| |
Collapse
|
32
|
Zhang Z, Li Y. Polymerized Small‐Molecule Acceptors for High‐Performance All‐Polymer Solar Cells. Angew Chem Int Ed Engl 2020. [DOI: 10.1002/ange.202009666] [Citation(s) in RCA: 12] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/29/2022]
Affiliation(s)
- Zhi‐Guo Zhang
- State Key Laboratory of Chemical Resource Engineering Beijing Advanced Innovation Center for Soft Matter Science and Engineering Beijing University of Chemical Technology Beijing 100029 China
| | - Yongfang Li
- Beijing National Laboratory for Molecular Sciences CAS Key Laboratory of Organic Solids Institute of Chemistry Chinese Academy of Sciences Beijing 100190 China
- Laboratory of Advanced Optoelectronic Materials College of Chemistry, Chemical Engineering and Materials Science Soochow University Suzhou Jiangsu 215123 China
| |
Collapse
|
33
|
Luo Z, Liu T, Ma R, Xiao Y, Zhan L, Zhang G, Sun H, Ni F, Chai G, Wang J, Zhong C, Zou Y, Guo X, Lu X, Chen H, Yan H, Yang C. Precisely Controlling the Position of Bromine on the End Group Enables Well-Regular Polymer Acceptors for All-Polymer Solar Cells with Efficiencies over 15. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2020; 32:e2005942. [PMID: 33118246 DOI: 10.1002/adma.202005942] [Citation(s) in RCA: 119] [Impact Index Per Article: 29.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 08/31/2020] [Revised: 09/24/2020] [Indexed: 06/11/2023]
Abstract
Recent advances in the development of polymerized A-D-A-type small-molecule acceptors (SMAs) have promoted the power conversion efficiency (PCE) of all-polymer solar cells (all-PSCs) over 13%. However, the monomer of an SMA typically consists of a mixture of three isomers due to the regio-isomeric brominated end groups (IC-Br(in) and IC-Br(out)). In this work, the two isomeric end groups are successfully separated, the regioisomeric issue is solved, and three polymer acceptors, named PY-IT, PY-OT, and PY-IOT, are developed, where PY-IOT is a random terpolymer with the same ratio of the two acceptors. Interestingly, from PY-OT, PY-IOT to PY-IT, the absorption edge gradually redshifts and electron mobility progressively increases. Theory calculation indicates that the LUMOs are distributed on the entire molecular backbone of PY-IT, contributing to the enhanced electron transport. Consequently, the PM6:PY-IT system achieves an excellent PCE of 15.05%, significantly higher than those for PY-OT (10.04%) and PY-IOT (12.12%). Morphological and device characterization reveals that the highest PCE for the PY-IT-based device is the fruit of enhanced absorption, more balanced charge transport, and favorable morphology. This work demonstrates that the site of polymerization on SMAs strongly affects device performance, offering insights into the development of efficient polymer acceptors for all-PSCs.
Collapse
Affiliation(s)
- Zhenghui Luo
- Shenzhen Key Laboratory of Polymer Science and Technology, College of Materials Science and Engineering, Shenzhen University, Shenzhen, 518060, P. R. China
- Department of Chemistry and Hong Kong Branch of Chinese National Engineering Research Center for Tissue Restoration & Reconstruction, Hong Kong University of Science and Technology (HKUST), Clear Water Bay, Kowloon, Hong Kong, P. R. China
| | - Tao Liu
- Department of Chemistry and Hong Kong Branch of Chinese National Engineering Research Center for Tissue Restoration & Reconstruction, Hong Kong University of Science and Technology (HKUST), Clear Water Bay, Kowloon, Hong Kong, P. R. China
| | - Ruijie Ma
- Department of Chemistry and Hong Kong Branch of Chinese National Engineering Research Center for Tissue Restoration & Reconstruction, Hong Kong University of Science and Technology (HKUST), Clear Water Bay, Kowloon, Hong Kong, P. R. China
| | - Yiqun Xiao
- Department of Physics, Chinese University of Hong Kong, New Territories, Hong Kong, 999077, P. R. China
| | - Lingling Zhan
- State Key Laboratory of Silicon Materials, MOE Key Laboratory of Macromolecular, Synthesis and Functionalization, Department of Polymer Science and Engineering, Zhejiang University, Hangzhou, 310027, P. R. China
| | - Guangye Zhang
- eFlexPV Limited (China), Plant B701, Guofu Cultural Creative Industry Plant Area, No. 16, Lanjing Middle Road, Zhukeng Community, Longtian Street, Pingshan District, Shenzhen, 518057, P. R. China
- eFlexPV Limited, Flat/RM B, 12/F, Hang Seng Causeway Bay BLDG, 28 Yee Wo Street, Causeway Bay, Hong Kong, 999077, P. R. China
| | - Huiliang Sun
- Department of Chemistry and Hong Kong Branch of Chinese National Engineering Research Center for Tissue Restoration & Reconstruction, Hong Kong University of Science and Technology (HKUST), Clear Water Bay, Kowloon, Hong Kong, P. R. China
- Department of Materials Science and Engineering and The Shenzhen Key Laboratory for Printed Organic Electronics, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong, 518055, P. R. China
| | - Fan Ni
- Shenzhen Key Laboratory of Polymer Science and Technology, College of Materials Science and Engineering, Shenzhen University, Shenzhen, 518060, P. R. China
| | - Gaoda Chai
- Department of Chemistry and Hong Kong Branch of Chinese National Engineering Research Center for Tissue Restoration & Reconstruction, Hong Kong University of Science and Technology (HKUST), Clear Water Bay, Kowloon, Hong Kong, P. R. China
| | - Junwei Wang
- Department of Materials Science and Engineering and The Shenzhen Key Laboratory for Printed Organic Electronics, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong, 518055, P. R. China
| | - Cheng Zhong
- Department of Chemistry, Wuhan University, Wuhan, 430072, P. R. China
| | - Yang Zou
- Shenzhen Key Laboratory of Polymer Science and Technology, College of Materials Science and Engineering, Shenzhen University, Shenzhen, 518060, P. R. China
| | - Xugang Guo
- Department of Materials Science and Engineering and The Shenzhen Key Laboratory for Printed Organic Electronics, Southern University of Science and Technology (SUSTech), No. 1088, Xueyuan Road, Shenzhen, Guangdong, 518055, P. R. China
| | - Xinhui Lu
- Department of Physics, Chinese University of Hong Kong, New Territories, Hong Kong, 999077, P. R. China
| | - Hongzheng Chen
- State Key Laboratory of Silicon Materials, MOE Key Laboratory of Macromolecular, Synthesis and Functionalization, Department of Polymer Science and Engineering, Zhejiang University, Hangzhou, 310027, P. R. China
| | - He Yan
- Department of Chemistry and Hong Kong Branch of Chinese National Engineering Research Center for Tissue Restoration & Reconstruction, Hong Kong University of Science and Technology (HKUST), Clear Water Bay, Kowloon, Hong Kong, P. R. China
| | - Chuluo Yang
- Shenzhen Key Laboratory of Polymer Science and Technology, College of Materials Science and Engineering, Shenzhen University, Shenzhen, 518060, P. R. China
- Department of Chemistry, Wuhan University, Wuhan, 430072, P. R. China
| |
Collapse
|
34
|
Xiang Y, Meng H, Yao Q, Chang Y, Yu H, Guo L, Xue Q, Zhan C, Huang J, Chen G. B ← N Bridged Polymer Acceptors with 900 nm Absorption Edges Enabling High-Performance All-Polymer Solar Cells. Macromolecules 2020. [DOI: 10.1021/acs.macromol.0c01995] [Citation(s) in RCA: 11] [Impact Index Per Article: 2.8] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/28/2023]
Affiliation(s)
- Ying Xiang
- College of Materials Science and Engineering, Huaqiao University, Xiamen 361021, P. R. China
| | - Huifeng Meng
- College of Materials Science and Engineering, Huaqiao University, Xiamen 361021, P. R. China
- Beijing National Laboratory for Molecular Sciences, CAS Key Laboratory of Photochemistry, Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190, P. R. China
| | - Qin Yao
- Institute of Polymer Optoelectronic Materials and Devices, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou 510640, P. R. China
| | - Yuan Chang
- Department of Chemistry and Hong Kong Branch of Chinese National Engineering Research Center for Tissue Restoration & Reconstruction, Hong Kong University of Science and Technology, Clear Water Bay, Kowloon 999077, Hong Kong
| | - Han Yu
- Department of Chemistry and Hong Kong Branch of Chinese National Engineering Research Center for Tissue Restoration & Reconstruction, Hong Kong University of Science and Technology, Clear Water Bay, Kowloon 999077, Hong Kong
| | - Liang Guo
- College of Materials Science and Engineering, Huaqiao University, Xiamen 361021, P. R. China
| | - Qifan Xue
- Institute of Polymer Optoelectronic Materials and Devices, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou 510640, P. R. China
| | - Chuanlang Zhan
- Key Laboratory of Excitonic Materials Chemistry and Devices (EMC&D), College of Chemistry and Environmental Science, Inner Mongolia Normal University, Huhhot 010022, P. R. China
- Beijing National Laboratory for Molecular Sciences, CAS Key Laboratory of Photochemistry, Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190, P. R. China
| | - Jianhua Huang
- College of Materials Science and Engineering, Huaqiao University, Xiamen 361021, P. R. China
| | - Guohua Chen
- College of Materials Science and Engineering, Huaqiao University, Xiamen 361021, P. R. China
| |
Collapse
|
35
|
Wang K, Dong S, Chen X, Zhou P, Zhang K, Huang J, Wang M. Improving the all-polymer solar cell performance by adding a narrow bandgap polymer as the second donor. RSC Adv 2020; 10:38344-38350. [PMID: 35517516 PMCID: PMC9057259 DOI: 10.1039/d0ra06143c] [Citation(s) in RCA: 5] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/15/2020] [Accepted: 09/23/2020] [Indexed: 11/25/2022] Open
Abstract
Ternary all-polymer solar cells are fabricated using an N2200 acceptor and two donor polymers (PF2 and PM2) with complementary absorption. The major donor PF2 is a relatively wide bandgap polymer that contributes the most photon absorption in the UV-vis region while the second donor PM2 improves the light harvesting due to its strong absorption in the near-IR region. By carefully tuning the ratio of two donor polymers, the best ratio of 9 : 1 : 5 (PF2 : PM2 : N2200) is achieved and shows a PCE of 6.90%, which is better than two binary devices. This work demonstrates an effective strategy of utilizing a narrow bandgap donor polymer as the second donor to improve the performance of all-polymer solar cells. Ternary all-polymer solar cells are fabricated using an N2200 acceptor and two donor polymers (PF2 and PM2) with complementary absorption.![]()
Collapse
Affiliation(s)
- Kai Wang
- Center for Advanced Low-Dimension Materials
- State Key Laboratory for Modification of Chemical Fibers and Polymer Materials
- College of Materials Science and Engineering
- Donghua University
- Shanghai 201620
| | - Sheng Dong
- Institute of Polymer Optoelectronic Materials & Devices
- State Key Laboratory of Luminescent Materials and Devices
- South China University of Technology
- Guangzhou 510640
- China
| | - Xudong Chen
- Shanghai International College of Design & Innovation
- Tongji University
- Shanghai 200080
- China
| | - Ping Zhou
- Shanghai International College of Design & Innovation
- Tongji University
- Shanghai 200080
- China
| | - Kai Zhang
- Institute of Polymer Optoelectronic Materials & Devices
- State Key Laboratory of Luminescent Materials and Devices
- South China University of Technology
- Guangzhou 510640
- China
| | - Jun Huang
- Center for Advanced Low-Dimension Materials
- State Key Laboratory for Modification of Chemical Fibers and Polymer Materials
- College of Materials Science and Engineering
- Donghua University
- Shanghai 201620
| | - Ming Wang
- Center for Advanced Low-Dimension Materials
- State Key Laboratory for Modification of Chemical Fibers and Polymer Materials
- College of Materials Science and Engineering
- Donghua University
- Shanghai 201620
| |
Collapse
|