A Top-Down Strategy to Engineer ActiveLayer Morphology for Highly Efficient and Stable All-Polymer Solar Cells

Rational Regulation of Layer-by-Layer Processed Active Layer via Trimer-Induced Pre-Swelling Strategy for Efficient and Robust Thick-Film Organic Solar Cells

Thick-film (>300 nm) organic solar cells (OSCs) have garnered intensifying attention due to their compatibility with commercial roll-to-roll printing technology for the large-scale continuous fabrication process. However, due to the uncontrollable donor/acceptor (D/A) arrangement in thick-film condition, the restricted exciton splitting and severe carrier traps significantly impede the photovoltaic performance and operability. Herein, combined with layer-by-layer deposition technology, a twisted 3D star-shaped trimer (BTT-Out) is synthesized to develop a trimer-induced pre-swelling (TIP) strategy, where the BTT-Out is incorporated into the buried D18 donor layer to enable the fabrication of thick-film OSCs. The integrated approach characterizations reveal that the exceptional configuration and spontaneous self-organization behavior of BTT-Out trimer could pre-swell the D18 network to facilitate the acceptor's infiltration and accelerate the formation of D/A interfaces. This enhancement triggers the elevated polarons formation with amplified hole-transfer kinetics, which is essential for the augmented exciton splitting efficiency. Furthermore, the regulated swelling process can initiate the favorable self-assembly of L8-BO acceptors, which would ameliorate carrier transport channels and mitigate carrier traps. As a result, the TIP-modified thin-film OSC devices achieve the champion performance of 20.3% (thin-film) and 18.8% (thick-film) with upgraded stability, among one of the highest performances reported of thick-film OSCs.

Different Sized Cycloalkyl Chains on Non-Fullerene Acceptors Enhance Molecular Packing, Film Morphology and Charge Transport for 19.62% Efficiency Organic Solar Cells

This work addresses the challenge of achieving advanced fibril morphology of non-fullerene acceptors (NFAs) in layer-by-layer organic solar cels (LBL-OSCs) by cycloalkyl chain strategy, focusing on ta series of Y6-type NFAs, namely BTP-C6, BTP-C8 and BTP-C12, featured with cyclohexyl, cyclooctyl and cyclododecyl chains with increasing steric hindrance. These side chains influenced significantly molecular planarity, packing and film morphology, which are critical for device performance. BTP-C6 exhibits optimal molecular packing and fibril network morphology, enabling efficient exciton dissociation, charge transport and balanced carrier mobilities, finally achieving PCEs of 19.28% and 19.62% with chloroform- and toluene-cast acceptor layers, respectively. BTP-C8 featuring enhanced planarity (dihedral angle 8.27°) showed the loosest packing (packing coefficient 49.6%) due to the increased steric hindrance of side chains, limiting intermolecular charge transport. Conversely, BTP-C12 formed a high crystalline and tightly packed 3D network but suffered from reduced intramolecular charge transfer caused by severe molecular distortion (dihedral angle 27.27°). The findings in this work underscore the critical role of side-chain engineering in governing molecular packing and morphology, offering a systematic understanding of the relationships between steric hindrance, crystallinity and device performance, while providing a rational design strategy for next-generation NFAs to advance high-performance LBL-OSCs.

Efficient Planar Heterojunction Organic Solar Cell with Enhanced Crystallization and Diffusivity of Acceptor

In the field of organic solar cells (OSCs), planar heterojunctions (PHJs) have received less attention. This study demonstrates that enhancing the crystallization and diffusivity of nonfullerene small-molecule acceptors (NF-SMAs) through sequential deposition significantly optimizes the morphology of PHJ OSCs, driving notable performance enhancements. An additive 1,2,4,5-tetrabromobenzene (TBrB) is employed during sequential deposition, enabling such desirable morphological control in OSCs. In situ UV-vis absorption spectroscopy reveals that TBrB selectively induces rapid aggregation of NF-SMAs, L8-BO, within subseconds. Structural analysis confirms that TBrB promotes the formation of a 3D "honeycomb" structure of L8-BO. Simultaneously, TBrB enhances L8-BO diffusivity into the D18 layer, resulting in a widened and well-intermixed region. These morphological optimizations improve the charge transfer efficiency and reduce bimolecular recombination, achieving a peak power conversion efficiency (PCE) of 19.25%. This study underscores the critical role of fine-tuning solidification processes in sequential deposition to optimize the morphology and performance of OSCs.

Donor-Interacting Arylated Carbazole Self-Assembled Monolayer Enables Highly Efficient and Stable Organic Photovoltaics

Carbazole-derived self-assembled monolayers (SAMs) are promising materials for hole-extraction layer (HEL) in conventional organic photovoltaics (OPVs). Here, a SAM Cbz-2Ph derived from 3,6-diphenylcarbazole is demonstrated. The large molecular dipole moment of Cbz-2Ph allows the modulation of electrode work function to facilitate hole extraction and maximize photovoltage, thus improving the OPV performance. Additionally, the flanking aryls of Cbz-2Ph help establish CH-π interactions for forming a dense and well-organized SAM HEL and exhibit stronger van der Waals interactions with the donor PM6 than acceptor BTP-eC9. The stronger SAM-donor interactions modulate the PM6 distribution in PM6:BTP-eC9 bulk-heterojunction film, leading to PM6 enrichment near HEL to facilitate efficient hole extraction to the ITO anode in conventional p-i-n OPVs. Consequently, binary PM6:BTP-eC9-based devices incorporating the Cbz-2Ph HEL demonstrate an impressive efficiency of 19.18%. These cells also showcase excellent operational stability, with a T80 lifetime of ≈1260 h at the maximum power point, over 10 times longer than those using the traditional PEDOT:PSS HEL (T80 ≈96 h). Furthermore, the universal applicability of Cbz-2Ph as a HEL is evident through its successful implementation in PM6:BTP-eC9:L8-BO-F-based ternary devices and PM6:BTP-eC9-based printed OPV devices, achieving a PCE of 19.30% and 16.96%, respectively.

Solution Sequential Deposition Pseudo-Planar Heterojunction: An Efficient Strategy for State-of-Art Organic Solar Cells

Organic solar cells (OSCs) are considered as a promising new generation of clean energy. Bulk heterojunction (BHJ) structure has been widely employed in the active layer of efficient OSCs. However, precise regulation of morphology in BHJ is still challenging due to the competitive coupling between crystallization and phase separation. Recently, a novel pseudo-planar heterojunction (PPHJ) structure, prepared through solution sequential deposition, has attracted much attention. It is an easy-to-prepare structure in which the phase separation structures, interfaces, and molecular packing can be separately controlled. Employing PPHJ structure, the properties of OSCs, such as power conversion efficiency, stability, transparency, flexibility, and so on, are usually better than its BHJ counterpart. Hence, a comprehensive understanding of the film-forming process, morphology control, and device performance of PPHJ structure should be considered. In terms of the representative works about PPHJ, this review first introduces the fabrication process of active layers based on PPHJ structure. Second, the widely applied morphology control methods in PPHJ structure are summarized. Then, the influences of PPHJ structure on device performance and other property are reviewed, which largely expand its application. Finally, a brief prospect and development tendency of PPHJ devices are discussed with the consideration of their challenges.

Nonhalogenated Solvent-Processed Efficient Ternary All-Polymer Solar Cells Enabled by the Introduction of a Naphthyloxy Group into the Side Chain of Polymer Donors

Conjugated polymer donors are crucial for enhancing the power conversion efficiencies (PCEs) in all-polymer solar cells (All-PSCs) in nonhalogenated solvents. In this work, three wide-band-gap polymer donors (Sil-D1, Ph-Sil-D1, and Nap-Sil-D1) based on dithienobenzothiadiazole (DTBT) and benzodithiophene (BDT) donor moieties optimized by side chain engineering were designed and synthesized. Alkyl (Sil-D1), phenyloxy (Ph-Sil-D1), and naphthyloxy (Nap-Sil-D1) alkyl siloxane side chain units were incorporated into these polymer donors, respectively. Notably, the Nap-Sil-D1 polymer donor had a greater conjugation length, π-electron delocalization, and improved dipole moment. The deepest highest occupied molecular orbital level of Nap-Sil-D1, with a high absorption coefficient, showed better aggregation properties. In addition, reduced bimolecular recombination and trap-state density generated a high charge transfer to cause a significant enhancement of open-circuit voltage, current density, and fill factor values of 0.94 V, 25.5 mA/cm2, and 70.4%, respectively, for the Nap-Sil-D1-blended All-PSC ternary device (PM6:Nap-Sil-D1:PY-IT), with the highest PCE of 16.8% in the o-xylene solvent, compared to other polymers (Sil-D1 and Ph-Sil-D1) with PCEs of 15.5 and 16.2%. As a result, this optimized device architecture was found to be the most promising as a nonhalogenated solvent processed in additive-free ternary All-PSCs with good stability.

Over 18.2% efficiency of layer-by-layer all-polymer solar cells enabled by homoleptic iridium(III) carbene complex as solid additive

The vertical phase distribution of active layers plays a vital role in balancing exciton dissociation and charge transport for achieving efficient polymer solar cells (PSCs). The layer-by-layer (LbL) PSCs are commonly prepared by using sequential spin-coating method from donor and acceptor solutions with distinct solvents and solvent additives. The enhanced exciton dissociation is expected in the LbL PSCs with efficient charge transport in the relatively neat donor or acceptor layers. In this work, a series of LbL all-polymer solar cells (APSCs) were fabricated with PM6 as donor and PY-DT as acceptor, and triplet material m-Ir(CPmPB)3 is deliberately incorporated into PY-DT layer to prolong exciton lifetimes of active layers. The power conversion efficiency (PCE) of LbL APSCs is improved to 18.24% from 17.32% by incorporating 0.3 wt% m-Ir(CPmPB)3 in PY-DT layer, benefiting from the simultaneously enhanced short-circuit current density (JSC) of 25.17 mA cm-2 and fill factor (FF) of 74.70%. The enhancement of PCE is attributed to the efficient energy transfer of m-Ir(CPmPB)3 to PM6 and PY-DT, resulting in the prolonged exciton lifetime in the active layer and the increased exciton diffusion distance. The efficient energy transfer from m-Ir(CPmPB)3 to PM6 and PY-DT layer can be confirmed by the increased photoluminescence (PL) intensity and the prolonged PL lifetime of PM6 and PY-DT in PM6 + m-Ir(CPmPB)3 and PY-DT + m-Ir(CPmPB)3 films. This study indicates that the triplet material as solid additive has great potential in fabricating efficient LbL APSCs by prolonging exciton lifetimes in active layers.

Manipulating Alkyl Inner Side Chain of Acceptor for Efficient As-Cast Organic Solar Cells

As-cast organic solar cells (OSCs) possess tremendous potential for low-cost commercial applications. Herein, five small-molecule acceptors (A1-A5) are designed and synthesized by selectively and elaborately extending the alkyl inner side chain flanking on the pyrrole motif to prepare efficient as-cast devices. As the extension of the alkyl chain, the absorption spectra of the films are gradually blue-shifted from A1 to A5 along with slightly uplifted lowest unoccupied molecular orbital energy levels, which is conducive for optimizing the trade-off between short-circuit current density and open-circuit voltage of the devices. Moreover, a longer alkyl chain improves compatibility between the acceptor and donor. The in situ technique clarifies that good compatibility will prolong molecular assembly time and assist in the preferential formation of the donor phase, where the acceptor precipitates in the framework formed by the donor. The corresponding film-formation dynamics facilitate the realization of favorable film morphology with a suitable fibrillar structure, molecular stacking, and vertical phase separation, resulting in an incremental fill factor from A1 to A5-based devices. Consequently, the A3-based as-cast OSCs achieve a top-ranked efficiency of 18.29%. This work proposes an ingenious strategy to manipulate intermolecular interactions and control the film-formation process for constructing high-performance as-cast devices.

Optimizing Double-Fibril Network Morphology via Solid Additive Strategy Enables Binary All-Polymer Solar Cells with 19.50% Efficiency

Double-fibril network morphology (DFNM), in which the donor and the acceptor can self-assemble into a double-fibril structure, is beneficial for exciton dissociation and charge transport in organic solar cells. Herein, it is demonstrated that such DFNM can be constructed and optimized in all-polymer solar cells (all-PSCs) with the assistance of 2-alkoxynaphthalene volatile solid additives. It is revealed that the incorporation of 2-alkoxynaphthalene can induce a stepwise regulation in the aggregation of donor and acceptor molecules during film casting and thermal annealing processes. Through altering the alkoxy of 2-alkoxynaphthalene solid additives, both the intermolecular interactions and molecular miscibility with the host materials can be precisely tuned, which allows for the optimization of the molecular aggregation process and facilitation of molecular self-assembly, and thus leading to reinforced molecular packing and optimized DFNM. As a result, an unprecedented efficiency of 19.50% (certified as 19.1%) is obtained for 2-ethoxynaphthalene-processed PM6:PY-DT-X all-PSCs with excellent photostability (T80 = 1750 h). This work reveals that the optimization of DFNM via solid additive strategy is a promising avenue to boosting the performance of all-PSCs.

Conjugation-Broken Dimer Acceptors Enable High-Efficiency, Stable, and Flexibility-Robust Organic Solar Cells

Dimer acceptors in organic solar cells (OSCs) offer distinct advantages, including a well-defined molecular structure and excellent batch-to-batch reproducibility. Their high glass transition temperature (Tg) aids in achieving an optimal kinetic morphology, thereby enhancing device stability. Currently, most of dimer acceptor materials are linked with conjugated units in order to obtain high power conversion efficiencies (PCEs). In this study, different from previous works on conjugation-linked dimer acceptors, a novel series of dimer acceptors are synthesized (named T1, T4, T6, and T12), each linked with different flexible alkyl linkers, and investigated their PCEs, device stability, and flexibility robustness. When blended with PM6, the T6-based device achieves a PCE of 17.09%, comparable to the fully conjugated T0-based device's PCE of 17.12%. The molecular dynamics simulations and density functional theory calculations suggested that flexible conjugation-broken linkers (FCBLs) promote intermolecular electronic couplings, thereby maintaining good electron mobilities of dimer acceptors. Notably, the T6-based device exhibits impressive long-term stability with a T80 lifetime of 1427 h, while in the T0-based device, T80 is only 350 h. The present work has thus established the relationship between the length of flexible alkyl linkers in such dimer acceptors and the performance and stability of OSCs, which is important to further designing new materials for the fabrication of efficient and stable OSCs.

Recent Progress of Oligomeric Non-Fullerene Acceptors for Efficient and Stable Organic Solar Cells

Organic solar cells (OSCs) have achieved remarkable power conversion efficiencies (PCEs) of over 19 % in the past few years due to the rapid development of non-fullerene acceptors (NFAs). However, the operational stability remains a great challenge that inhibits their commercialization. Recently, oligomeric NFAs (ONFAs) have attracted great attention, which not only can deliver excellent device performance, but also improve the thermal-/photo- stability of OSCs. This is attributed to the suppressed molecular diffusion of ONFAs associated with their high glass-transition temperature (Tg) and improved thermodynamic properties of ONFAs. Herein, we focus on investigating the correction between the ONFA chemical structure, material properties, device performance, and stability. In addition, we also try to point out the challenges in synthesizing ONFAs and provide potential directions for future ONFA designs.

Layer-by-Layer Organic Solar Cells Enabled by 1,3,4-Selenadiazole-Containing Crystalline Small Molecule with Double-Fibril Network Morphology

A double-fibril network of the photoactive layer morphology is recognized as an ideal structure facilitating exciton diffusion and charge carrier transport for high-performance organic solar cells (OSCs). However, in the layer-by-layer processed OSCs (LbL-OSCs), polymer donors and small molecule acceptors (SMAs) are separately deposited, and it is challenging to realize a fibril network of pure SMAs with the absence of tight interchain entanglement as polymers. In this work, crystalline small molecule donors (SMDs), named TDZ-3TR and SeDZ-3TR, were designed and introduced into the L8-BO acceptor solution, forcing the phase separation and molecular fibrilization. SeDZ-3TR showed higher crystallinity and lower miscibility with L8-BO acceptor than TDZ-3TR, enabling more driving force to favor the phase separation and better molecular fibrilization of L8-BO. On the other hand, two donor polymers of PM6 and D18 with different fibril widths and lengths were put together to optimize the fibril network of the donor layer. The simultaneously optimization of the acceptor and donor layers resulted in a more ideal double-fibril network of the photoactive layer and an impressive power conversion efficiency (PCE) of 19.38 % in LbL-OSCs.

Dithienoquinoxalineimide-Based Polymer Donor Enables All-Polymer Solar Cells Over 19 % Efficiency

All-polymer solar cells (all-PSCs) have been regarded as one of the most promising candidates for commercial applications owing to their outstanding advantages such as mechanical flexibility, light weight and stable film morphology. However, compared to large amount of new-emerging excellent polymer acceptors, the development of high-performance polymer donor lags behind. Herein, a new D-π-A type polymer donor, namely QQ1, was developed based on dithienoquinoxalineimide (DTQI) as the A unit, benzodithiophene with thiophene-conjugated side chains (BDTT) as the D unit, and alkyl-thiophene as the π-bridge, respectively. QQ1 not only possesses a strong dipole moment, but also shows a wide band gap of 1.80 eV and a deep HOMO energy level of -5.47 eV, even without halogen substituents that are commonly indispensable for high-performance polymer donors. When blended with a classic polymer acceptor PY-IT, the QQ1-based all-PSC delivers an outstanding PCE of 18.81 %. After the introduction of F-BTA3 as the third component, a record PCE of 19.20 % was obtained, the highest value reported so far for all-PSCs. The impressive photovoltaic performance originates from broad absorption range, reduced energy loss, and compact π-π stacking. These results provide new insight in the rational design of novel nonhalogenated polymer donors for further development of all-PSCs.

Eliminating the Burn-in Loss of Efficiency in Organic Solar Cells by Applying Dimer Acceptors as Supramolecular Stabilizers

The meta-stable active layer morphology of organic solar cells (OSCs) is identified as the main cause of the rapid burn-in loss of power conversion efficiency (PCE) during long-term device operation. However, effective strategies to eliminate the associated loss mechanisms from the initial stage of device operation are still lacking, especially for high-efficiency material systems. Herein, the introduction of molecularly engineered dimer acceptors with adjustable thermal transition properties into the active layer of OSCs to serve as supramolecular stabilizers for regulating the thermal transitions and optimizing the crystallization of the absorber composites is reported. By establishing intimate π-π interactions with small-molecule acceptors, these stabilizers can effectively reduce the trap-state density (Nt) in the devices to achieve excellent PCEs over 19%. More importantly, the low Nt associated with an initially optimized morphology can be maintained under external stresses to significantly reduce the PCE burn-in loss in devices. This research reveals a judicious approach to improving OPV stability by establishing a comprehensive correlation between material properties, active-layer morphology, and device performance, for developing burn-in-free OSCs.

Current State and Future Perspectives of Printable Organic and Perovskite Solar Cells

Photovoltaic technology presents a sustainable solution to address the escalating global energy consumption and a reliable strategy for achieving net-zero carbon emissions by 2050. Emerging photovoltaic technologies, especially the printable organic and perovskite solar cells, have attracted extensive attention due to their rapidly transcending power conversion efficiencies and facile processability, providing great potential to revolutionize the global photovoltaic market. To accelerate these technologies to translate from the laboratory scale to the industrial level, it is critical to develop well-defined and scalable protocols to deposit high-quality thin films of photoactive and charge-transporting materials. Herein, the current state of printable organic and perovskite solar cells is summarized and the view regarding the challenges and prospects toward their commercialization is shared. Different printing techniques are first introduced to provide a correlation between material properties and printing mechanisms, and the optimization of ink formulation and film-formation during large-area deposition of different functional layers in devices are then discussed. Engineering perspectives are also discussed to analyze the criteria for module design. Finally, perspectives are provided regarding the future development of these solar cells toward practical commercialization. It is believed that this perspective will provide insight into the development of printable solar cells and other electronic devices.

Regulating Phase Separation Kinetics for High-Efficiency and Mechanically Robust All-Polymer Solar Cells

All-polymer solar cells (all-PSCs) possess excellent operation stability and mechanical robustness than other types of organic solar cells, thereby attracting considerable attention for wearable flexible electron devices. However, the power conversion efficiencies (PCEs) of all-PSCs are still lagging behind those of small-molecule-acceptor-based systems owing to the limitation of photoactive materials and unsatisfactory blend morphology. In this work, a novel terpolymer, denoted as PBDB-TFCl (poly4,8-bis(5-(2-ethylhexyl)-4-fluorothiophen-2-yl)benzo[1,2-b:4,5-b″]dithiophene-1,3-bis(2-ethylhexyl)-5,7-di(thiophen-2-yl)-4H,8H-benzo[1,2-c:4,5-c″]dithiophene-4,8-dione-4,8-bis(4-chloro-5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b:4,5-b']dithiophene), is used as an electron donor coupled with a ternary strategy to optimize the performance of all-PSCs. The addition of PBDB-TCl unit deepens the highest occupied molecular orbital energy level, reducing voltage losses. Moreover, the introduction of the guest donor (D18-Cl) effectively regulates the phase-transition kinetics of PBDB-TFCl:D18-Cl:PY-IT during the film formation, leading to ideal size of aggregations and enhanced crystallinity. PBDB-TFCl:D18-Cl:PY-IT devices exhibit a PCE of 18.6% (certified as 18.3%), judged as the highest value so far obtained with all-PSCs. Besides, based on the ternary active layer, the manufactured 36 cm2 flexible modules exhibit a PCE of 15.1%. Meanwhile, the ternary PSCs exhibit superior photostability and mechanical stability. In summary, the proposed strategy, based on molecular design and the ternary strategy, allows optimization of the all-polymer blend morphology and improvement of the photovoltaic performance for stable large-scale flexible PSCs.

Hot-Casting Strategy Empowers High-Boiling Solvent-Processed Organic Solar Cells with Over 18.5% Efficiency

Most top-rank organic solar cells (OSCs) are manufactured by the halogenated solvent chloroform, which possesses a narrow processing window due to its low-boiling point. Herein, based on two high-boiling solvents, halogenated solvent chlorobenzene (CB) and non-halogenated green solvent ortho-xylene (OX), preparing active layers with the hot solution is put forward to enhance the performance of the OSCs. In situ test and morphological characterization clarify that the hot-casting strategy assists in the fast and synchronous molecular assembly of both donor and acceptor in the active layer, contributing to preferable donor/acceptor ratio, vertical phase separation, and molecular stacking, which is beneficial to charge generation and extraction. Based on the PM6:BO-4Cl, the hot-casting OSCs with a wide processing window achieve efficiencies of 18.03% in CB and 18.12% in OX, which are much higher than the devices processed with room temperature solution. Moreover, the hot-casting devices with PM6:BTP-eC9 deliver a remarkable fill factor of 80.31% and efficiency of 18.52% in OX, representing the record value among binary devices with green solvent. This work demonstrates a facile strategy to manipulate the molecular distribution and arrangement for boosting the efficiency of OSCs with high-boiling solvents.

A Water-Processed Mesoscale Structure Enables 18.5% Efficient Binary Layer-by-Layer Organic Solar Cells

The two-step layer-by-layer (LBL) deposition of donor and acceptor films enables desired vertical phase separation and high performance in organic solar cells (OSCs), which becomes a promising technology for large-scale printing devices. However, limitations including the use of toxic solvents and unpredictable infiltration between donor and acceptor still hinder the commercial production of LBL OSCs. Herein, we developed a water-based nanoparticle (NP) ink containing donor polymer to construct a mesoscale structure that could be infiltrated with an acceptor solution. Using non-halogen o-xylene for acceptor deposition, the LBL strategy with a mesoscale structure delivered outstanding efficiencies of 18.5% for binary PM6:L8-BObased LBL OSCs. Enhanced charge carrier mobility and restricted trap states were observed in the meso-LBL devices with optimized vertical morphology. It is believed that the findings in this work will bring about more research interest and effort on eco-friendly processing in preparation for the industrial production of OSCs.

Central Core Substitutions and Film-Formation Process Optimization Enable Approaching 19% Efficiency All-Polymer Solar Cells

Molecular interactions and film-formation processes greatly impact the blend film morphology and device performances of all-polymer solar cells (all-PSCs). Molecular structure, such as the central cores of polymer acceptors, would significantly influence this process. Herein, the central core substitutions of polymer acceptors are adjusted and three quinoxaline (Qx)-fused-core-based materials, PQx1, PQx2, and PQx3 are synthesized. The molecular aggregation ability and intermolecular interaction are systematically regulated, which subsequently influence the film-formation process and determine the resulting blend film morphology. As a result, PQx3, with favorable aggregation ability and moderate interaction with polymer donor PM6, achieves efficient all-PSCs with a high power conversion efficiency (PCE) of 17.60%, which could be further improved to 18.06% after carefully optimizing device annealing and interface layer. This impressive PCE is one of the highest values for binary all-PSCs based on the classical polymer donor PM6. PYF-T-o is also involved in promoting light utilization, and the resulting ternary device shows an impressive PCE of 18.82%. In addition, PM6:PQx3-based devices exhibit high film-thickness tolerance, superior stability, and considerable potential for large-scale devices (16.23% in 1 cm2 device). These results highlight the importance of structure optimization of polymer acceptors and film-formation process control for obtaining efficient and stable all-PSCs.

Understanding the Role of Removable Solid Additives: Selective Interaction Contributes to Vertical Component Distributions

Sequentially deposited organic solar cells (SD-OSCs) have attracted great attention owing to their ability in achieving a more favorable, vertically phase-separated morphology to avoid the accumulation of counter charges at absorber/transporting layer interfaces. However, the processing of SD-OSCs is still quite challenging in preventing the penetration of small-molecule acceptors into the polymer donor layer via erosion or swelling. Herein, solid additives (SAs) with varied electrostatic potential distributions and steric hinderance are introduced into SD-OSCs to investigate the effect of evaporation dynamics and selective interaction on vertical component distribution. Multiple modelings indicate that the π-π interaction dominates the interactions between aromatic SAs and active layer components. Among them, p-dibromobenzene shows a stronger interaction with the donor while 2-chloronaphthalene (2-CN) interacts more preferably with acceptor. Combining the depth-dependent morphological study aided by multiple X-ray scattering methods, it is concluded that the evaporation of SAs can drive the stronger-interaction component upward to the surface, while having minor impact on the overall molecular packing. Ultimately, the 2-CN-treated devices with reduced acceptor concentration at the bottom surface deliver a high power conversion efficiency of 19.2%, demonstrating the effectiveness of applying selective interactions to improve the vertical morphology of OSCs by using SAs with proper structure.

Sequential Deposition of Multicomponent Bulk Heterojunctions Increases Efficiency of Organic Solar Cells

Constructing tandem and multi-blend organic solar cells (OSCs) is an effective way to overcome the absorption limitations of conventional single-junction devices. However, these methods inevitably require tedious multilayer deposition or complicated morphology-optimization procedures. Herein, sequential deposition is utilized as an effective and simple method to fabricate multicomponent OSCs with a double-bulk heterojunction (BHJ) structure of the active layer to further improve photovoltaic performance. Two efficient donor-acceptor pairs, D18-Cl:BTP-eC9 and PM6:L8-BO, are sequentially deposited to form the D18-Cl:BTP-eC9/PM6:L8-BO double-BHJ active layer. In these double-BHJ OSCs, light absorption is significantly improved, and optimal morphology is also retained without requiring a more complicated morphology optimization involved in quaternary blends. Compared to the quaternary blend devices, energy loss (E_loss ) is also reduced by rationally matching each donor with an appropriate acceptor. Consequently, the power conversion efficiency (PCE) is improved from 18.25% for D18-Cl:BTP-eC9 and 18.69% for PM6:L8-BO based binary blend OSCs to 19.61% for the double-BHJ OSCs. In contrast, a D18-Cl:PM6:L8-BO:BTP-eC9 quaternary blend of OSCs exhibited a dramatically reduced PCE of 15.83%. These results demonstrate that a double-BHJ strategy, with a relatively simple processing procedure, can potentially enhance the device performance of OSCs and lead to more widespread use.

High-Efficiency and Mechanically Robust All-Polymer Organic Photovoltaic Cells Enabled by Optimized Fibril Network Morphology

All-polymer organic photovoltaic (OPV) cells possessing high photovoltaic performance and mechanical robustness are promising candidates for flexible wearable devices. However, developing photoactive materials with good mechanical properties and photovoltaic performance so far remains challenging. In this work, a polymer donor PBDB-TF with a high weight-average molecular weight (M_w ) is introduced to enable highly efficient all-polymer OPV cells featuring excellent mechanical reliability. By incorporating the high-M_w PBDB-TF as a third component into the PBQx-TF:PY-IT blend, the bulk heterojunction morphology is finely tuned with a more compact π-π stacking distance, affording efficient pathways for charge transport as well as mechanical stress dissipation. Hence, all-polymer OPV cells based on the ternary blend film demonstrate a maximum power conversion efficiency (PCE) of 18.2% with an outstanding fill factor of 0.796. The flexible OPV cell delivers a decent PCE of 16.5% with high mechanical stability. These results present a promising strategy to address the mechanical properties and boost the photovoltaic performance of all-polymer OPV cells.

End Group Effect of Asymmetric Benzodithiophene-Based Donor with Liquid-Crystal State for Small-Molecule Binary Solar Cell

Liquid-crystal small molecule donor (LC-SMD) is a new type organic semiconductor, which is attractive not only for the easy synthesis and purification, well-defined chemical structures, etc., but also for the LC state that makes the crystallinity and aggregation state of molecules adjustable. Here, one new LC-SMD (a-BTR-H4) is synthesized with 1D alkoxyl and 2D thiophene-alkylthiol side-chained benzo[1,2-b:4,5-b']dithiophene core, trithiophene π-bridge, and 3-(2-ethylhexyl) rhodanine end group. a-BTR-H4 shows low LC transition temperature, 117 °C, however, counterpart material (a-BTR-H5) with the same main structure but 3-ethyl rhodanine terminal group does not show LC properties. Although a-BTR-H4/H5 show similar Ultraviolet-visible absorption spectrum and energy levels, a-BTR-H4 affords relatively high photovoltaic performances due to favorable blend morphology produced by the consistent annealing temperature of Y6-based accepters and liquid crystal temperature of donors. Preliminary results indicate that a-BTR-H4 gains a power conversion efficiency (PCE) of 11.36% for Y6-based devices, which is ascribed to better light harvest as well as balanced carrier generation and transport, while a-BTR-H5 obtains 7.57% PCE. Therefore, some materials with unique nematic LC phase have great application potential in organic electronics, and further work to utilize a-BTR-H4 for high-performance device is underway.

Improved Molecular Ordering in a Ternary Blend Enables All-Polymer Solar Cells over 18% Efficiency

Although all-polymer solar cells (all-PSCs) show great commercialization prospects, their power conversion efficiencies (PCEs) still fall behind their small molecule acceptor-based counterparts. In all-polymer blends, the optimized morphology and high molecular ordering are difficult to achieve since there is troublesome competition between the crystallinity of the polymer donor and acceptor during the film-formation process. Therefore, it is challenging to improve the performance of all-PSCs. Herein, a ternary strategy is adopted to modulate the morphology and the molecular crystallinity of an all-polymer blend, in which PM6:PY-82 is selected as the host blend and PY-DT is employed as a guest component. Benefiting from the favorable miscibility of the two acceptors and the higher regularity of PY-DT, the ternary matrix features a well-defined fibrillar morphology and improved molecular ordering. Consequently, the champion PM6:PY-82:PY-DT device produces a record-high PCE of 18.03%, with simultaneously improved open-circuit voltage, short-circuit current and fill factor in comparison with the binary devices. High-performance large-area (1 cm² ) and thick-film (300 nm) all-PSCs are also successfully fabricated with PCEs of 16.35% and 15.70%, respectively.Moreover, 16.5 cm² organic solar module affords an encouraging PCE of 13.84% when using the non-halogenated solvent , showing the great potential of "Lab-to-Fab" transition of all-PSCs.

19.10% Efficiency and 80.5% Fill Factor Layer-by-Layer Organic Solar Cells Realized by 4-Bis(2-Thienyl)Pyrrole-2,5-Dione Based Polymer Additives for Inducing Vertical Segregation Morphology

The morphology plays a key role in determining the charge generation and collection process, thus impacting the performances of organic solar cells (OSCs). The limited selection pool of additives to optimize the morphology of OSCs, especially for the emerging layer-by-layer (LbL) OSCs, impeding the improvements of photovoltaic performances. Herein, a new method of using conjugated polymers as the additives to optimize the morphology for improving the photovoltaic performances of LbL-OSCs is reported. Four polymers of PH, PS, PF, and PCl are developed with different side chains. These polymers exhibit poor performances as donor materials and additives in the BHJ devices, due to the unsuitable energy level alignment and unfavorable molecular interactions. By contrast, they can be served as efficient additives to optimize the PM6 fibril matrix for facilitating the penetration of BTP-eC9 and forming an intertwined D/A bicontinuous network with a vertical segregation. Such morphology is optimized by side chain engineering, which enables the progressive improvement of the charge separation and collection. As a result, adding a small amount of PCl as the additive, the optimized morphology contributes to a champion PCE of 19.10% with a high FF of 80.5%.

Ternary All-Polymer Solar Cells with Efficiency up to 18.14% Employing a Two-Step Sequential Deposition

Achieving a finely tuned active layer morphology with a suitable vertical phase to facilitate both charge generation and charge transport has long been the main goal for pursuing the highly efficient bulk heterojunction all-polymer solar cells (all-PSCs). Herein, a solution to address the above challenge via synergistically combining the ternary blend strategy and the layer-by-layer (LbL) procedure is proposed. By introducing a synthesized polymer acceptor (P_A ), PY-Cl, with higher crystallinity into the designed host acceptor PY-SSe-V, vertical phase distribution and molecular ordering of the LbL-type ternary all-PSCs can be improved in comparison to the LbL-type PM6/PY-SSe-V binary all-PSCs. The formation of the superior bulk microstructure can not only promote charge transport and extraction properties but also reduce energetic disorder and non-radiative recombination loss, thus improving all three photovoltaic parameters simultaneously. Consequently, the PM6/(PY-SSe-V:PY-Cl) ternary all-PSCs show the best efficiency of 18.14%, which is among the highest values reported to date for all-PSCs. This work provides a facile and effective LbL-type ternary strategy for obtaining high-efficiency all-PSCs.