An Organic Mixed Ion-Electron Conductor for Power Electronics

Boosting Electronic Charge Transport in Conductive Hydrogels via Rapid Ion-Electron Transduction

Traditional design of conductive hydrogels involves embedding conductive components within a hydrated polymeric network to establish interconnected electron pathways. While the hydration shell of the polymeric network is typically considered insulating, we demonstrate that it can enhance electron transport. Using a PEDOT:PSS hydrogel, we propose a hierarchical network with an inhomogeneous topological structure, consisting of entangled PSS chains, dense PSS assemblies, and PEDOT microcrystals. In the hydrated state, the dense PSS assemblies significantly lower the energy barrier for electron hopping between PEDOT microcrystals, thereby promoting electron transport. As a result, the charge transport mechanism in these hydrogels is predominantly electronic rather than ionic, effectively mimicking the behavior of electronic conductors. The charge transport rate reaches up to 2 × 106 m s-1, which is approximately five orders of magnitude higher than that of ion-based processes. This characteristic imparts the hydrogels with kinetically sensitive ion-electron transduction, enabling time-resolved electrochemical analysis of biochemical processes.

Compatibility of cellulose-PEDOT:PSS composites and anions in solid-state organic electrochemical transistors

We investigate the effects of water-processable celluloses on the charge-transport properties in the conducting polymer composites and their solid-state organic electrochemical transistors (OECTs). Water-soluble methyl cellulose (MC) and water-dispersible cellulose nanofiber (CNF) are blended with poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) in solution and used as a conductive channel. Both cellulose-PEDOT:PSS composites show fibrillar structures in thin films with respective dimensions of cellulose. The electrical conductivity was increased with 5-10 wt% of cellulose in the composite. The solid-state OECTs show better performance when the ionogel contains 1-ethyl-3-methylimidazolium triflate (EMIM:OTf) compared to the system with the commonly used EMIM bis(trifluoromethyl sulfonyl)imide (EMIM:TFSI). The MC-PEDOT:PSS composite paired with an EMIM:OTf-based ionogel exhibits a high figure-of-merit (μC⁎) of OECTs of >50 F cm-1 V-1 s-1 and an on-to-off current ratio of >103. Our results show that cellulose and EMIM:OTf are compatible with PEDOT:PSS and that appropriate materials pairing can improve the properties of PEDOT:PSS-based composites and the performance of their electrochemical devices.

Electrically conductive "SMART" hydrogels for on-demand drug delivery

In the current transformative era of biomedicine, hydrogels have established their presence in biomaterials due to their superior biocompatibility, tuneability and resemblance with native tissue. However, hydrogels typically exhibit poor conductivity due to their hydrophilic polymer structure. Electrical conductivity provides an important enhancement to the properties of hydrogel-based systems in various biomedical applications such as drug delivery and tissue engineering. Consequently, researchers are developing combinatorial strategies to develop electrically responsive "SMART" systems to improve the therapeutic efficacy of biomolecules. Electrically conductive hydrogels have been explored for various drug delivery applications, enabling higher loading of therapeutic cargo with on-demand delivery. This review emphasizes the properties, mechanisms, fabrication techniques and recent advancements of electrically responsive "SMART" systems aiding on-site drug delivery applications. Additionally, it covers prospects for the successful translation of these systems into clinical research.

Thermoelectric Materials and Devices for Advanced Biomedical Applications

Thermoelectrics (TEs), enabling the direct conversion between heat and electrical energy, have demonstrated extensive application potential in biomedical fields. Herein, the mechanism of the TE effect, recent developments in TE materials, and the biocompatibility assessment of TE materials are provided. In addition to the fundamentals of TEs, a timely and comprehensive review of the recent progress of advanced TE materials and their applications is presented, including wearable power generation, personal thermal management, and biosensing. In addition, the new-emerged medical applications of TE materials in wound healing, disease treatment, antimicrobial therapy, and anti-cancer therapy are thoroughly reviewed. Finally, the main challenges and future possibilities are outlined for TEs in biomedical fields, as well as their material selection criteria for specific application scenarios. Together, these advancements can provide innovative insights into the development of TEs for broader applications in biomedical fields.

Stretchable and biodegradable plant-based redox-diffusion batteries

The redox-diffusion (RD) battery concept introduces an environmentally friendly solution for stretchable batteries in autonomous wearable electronics. By utilising plant-based redox-active biomolecules and cellulose fibers for the electrode scaffold, separator membrane, and current collector, along with a biodegradable elastomer encapsulation, the battery design overcomes the reliance on unsustainable transition metal-based active materials and non-biodegradable elastomers used in existing stretchable batteries. Importantly, it addresses the drawback of limited attainable battery capacity, where increasing the active material loading often leads to thicker and stiffer electrodes with poor mechanical properties. The concept decouples the active material loading from the mechanical structure of the electrode, enabling high mass loadings, while retaining a skin-like young's modulus and stretchability. A stretchable ion-selective membrane facilitates the RD process, allowing two separate redox couples, while preventing crossovers. This results in a high-capacity battery cell that is both electrochemically and mechanically stable, engineered from sustainable plant-based materials. Notably, the battery components are biodegradable at the end of their life, addressing concerns of e-waste and resource depletion.

Organic Mixed Ionic-Electronic Conductors for Bioelectronic Sensors: Materials and Operation Mechanisms

The field of organic mixed ionic-electronic conductors (OMIECs) has gained significant attention due to their ability to transport both electrons and ions, making them promising candidates for various applications. Initially focused on inorganic materials, the exploration of mixed conduction has expanded to organic materials, especially polymers, owing to their advantages such as solution processability, flexibility, and property tunability. OMIECs, particularly in the form of polymers, possess both electronic and ionic transport functionalities. This review provides an overview of OMIECs in various aspects covering mechanisms of charge transport including electronic transport, ionic transport, and ionic-electronic coupling, as well as conducting/semiconducting conjugated polymers and their applications in organic bioelectronics, including (multi)sensors, neuromorphic devices, and electrochromic devices. OMIECs show promise in organic bioelectronics due to their compatibility with biological systems and the ability to modulate electronic conduction and ionic transport, resembling the principles of biological systems. Organic electrochemical transistors (OECTs) based on OMIECs offer significant potential for bioelectronic applications, responding to external stimuli through modulation of ionic transport. An in-depth review of recent research achievements in organic bioelectronic applications using OMIECs, categorized based on physical and chemical stimuli as well as neuromorphic devices and circuit applications, is presented.

Ultrastrong Ionotronic Films Showing Electrochemical Osmotic Actuation

A multifunctional soft material with high ionic and electrical conductivity, combined with high mechanical properties and the ability to change shape can enable bioinspired responsive devices and systems. The incorporation of all these characteristics in a single material is very challenging, as the improvement of one property tends to reduce other properties. Here, a nanocomposite film based on charged, high-aspect-ratio 1D flexible nanocellulose fibrils, and 2D Ti3 C2 Tx MXene is presented. The self-assembly process results in a stratified structure with the nanoparticles aligned in-plane, providing high ionotronic conductivity and mechanical strength, as well as large water uptake. In hydrogel form with 20 wt% liquid, the electrical conductivity is over 200 S cm-1 and the in-plane tensile strength is close to 100 MPa. This multifunctional performance results from the uniquely layered composite structure at nano- and mesoscales. A new type of electrical soft actuator is assembled where voltage as low as ±1 V resulted in osmotic effects and giant reversible out-of-plane swelling, reaching 85% strain.

Towards biodegradable conducting polymers by incorporating seaweed cellulose for decomposable wearable heaters

Thermotherapy shows significant potential for pain relief and enhanced blood circulation in wildlife rehabilitation, particularly for injured animals. However, the widespread adoption of this technology is hindered by the lack of biodegradable, wearable heating pads and concerns surrounding electronic waste (E-waste) in natural habitats. This study addresses this challenge by investigating an environmentally-friendly composite comprising poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS), seaweed cellulose, and glycerol. Notably, this composite exhibits remarkable biodegradability, losing half of its weight within one week and displaying noticeable edge degradation by the third week when placed in soil. Moreover, it demonstrates impressive heating performance, reaching a temperature of 51 °C at a low voltage of 1.5 V, highlighting its strong potential for thermotherapy applications. The combination of substantial biodegradability and efficient heating performance offers a promising solution for sustainable electronic applications in wildlife rehabilitation and forest monitoring, effectively addressing the environmental challenges associated with E-waste.

Correlations among Firing Rates of Tactile, Thermal, Gustatory, Olfactory, and Auditory Sensations Mimicked by Artificial Hybrid Fluid (HF) Rubber Mechanoreceptors

In order to advance the development of sensors fabricated with monofunctional sensation systems capable of a versatile response to tactile, thermal, gustatory, olfactory, and auditory sensations, mechanoreceptors fabricated as a single platform with an electric circuit require investigation. In addition, it is essential to resolve the complicated structure of the sensor. In order to realize the single platform, our proposed hybrid fluid (HF) rubber mechanoreceptors of free nerve endings, Merkel cells, Krause end bulbs, Meissner corpuscles, Ruffini endings, and Pacinian corpuscles mimicking the bio-inspired five senses are useful enough to facilitate the fabrication process for the resolution of the complicated structure. This study used electrochemical impedance spectroscopy (EIS) to elucidate the intrinsic structure of the single platform and the physical mechanisms of the firing rate such as slow adaption (SA) and fast adaption (FA), which were induced from the structure and involved the capacitance, inductance, reactance, etc. of the HF rubber mechanoreceptors. In addition, the relations among the firing rates of the various sensations were clarified. The adaption of the firing rate in the thermal sensation is the opposite of that in the tactile sensation. The firing rates in the gustation, olfaction, and auditory sensations at frequencies of less than 1 kHz have the same adaption as in the tactile sensation. The present findings are useful not only in the field of neurophysiology, to research the biochemical reactions of neurons and brain perceptions of stimuli, but also in the field of sensors, to advance salient developments in sensors mimicking bio-inspired sensations.

A Mixed Protonic-Electronic Conductor Base on the Host-Guest Architecture of 2D Metal-Organic Layers and Inorganic Layers

The key to designing and fabricating highly efficient mixed protonic-electronic conductors materials (MPECs) is to integrate the mixed conductive active sites into a single structure, to break through the shortcomings of traditional physical blending. Herein, based on the host-guest interaction, an MPEC is consisted of 2D metal-organic layers and hydrogen-bonded inorganic layers by the assembly methods of layered intercalation. Noticeably, the 2D intercalated materials (≈1.3 nm) exhibit the proton conductivity and electron conductivity, which are 2.02 × 10^-5 and 3.84 × 10^-4 S cm^-1 at 100 °C and 99% relative humidity, much higher than these of pure 2D metal-organic layers (>>1.0 × 10^-10 and 2.01×10^-8 S cm^-1 ), respectively. Furthermore, combining accurate structural information and theoretical calculations reveals that the inserted hydrogen-bonded inorganic layers provide the proton source and a networks of hydrogen-bonds leading to efficient proton transport, meanwhile reducing the bandgap of hybrid architecture and increasing the band electron delocalization of the metal-organic layer to greatly elevate the electron transport of intrinsic 2D metal-organic frameworks.

Elastoplastic behavior of anisotropic, physically crosslinked hydrogel networks comprising stiff, charged fibrils in an electrolyte

Fibrillar hydrogels are remarkably stiff, low-density networks that can hold vast amounts of water. These hydrogels can easily be made anisotropic by orienting the fibrils using different methods. Unlike the detailed and established descriptions of polymer gels, there is no coherent theoretical framework describing the elastoplastic behavior of fibrillar gels, especially concerning anisotropy. In this work, the swelling pressures of anisotropic fibrillar hydrogels made from cellulose nanofibrils were measured in the direction perpendicular to the fibril alignment. This experimental data was used to develop a model comprising three mechanical elements representing the network and the osmotic pressure due to non-ionic and ionic surface groups on the fibrils. At low solidity, the stiffness of the hydrogels was dominated by the ionic swelling pressure governed by the osmotic ingress of water. Fibrils with different functionality show the influence of aspect ratio, chemical functionality, and the remaining amount of hemicelluloses. This general model describes physically crosslinked hydrogels comprising fibrils with high flexural rigidity - that is, with a persistence length larger than the mesh size. The experimental technique is a framework to study and understand the importance of fibrillar networks for the evolution of multicellular organisms, like plants, and the influence of different components in plant cell walls.

Hydrogels with electrically conductive nanomaterials for biomedical applications

Hydrogels, soft 3D materials of cross-linked hydrophilic polymer chains with a high water content, have found numerous applications in biomedicine because of their similarity to native tissue, biocompatibility and tuneable properties. In general, hydrogels are poor conductors of electric current, due to the insulating nature of commonly-used hydrophilic polymer chains. A number of biomedical applications require or benefit from an increased electrical conductivity. These include hydrogels used as scaffolds for tissue engineering of electroactive cells, as strain-sensitive sensors and as platforms for controlled drug delivery. The incorporation of conductive nanomaterials in hydrogels results in nanocomposite materials which combine electrical conductivity with the soft nature, flexibility and high water content of hydrogels. Here, we review the state of the art of such materials, describing the theories of current conduction in nanocomposite hydrogels, outlining their limitations and highlighting methods for improving their electrical conductivity.

Electron-Deficient Polycyclic Molecules via Ring Fusion for n-Type Organic Electrochemical Transistors

The primary challenge for n-type small-molecule organic electrochemical transistors (OECTs) is to improve their electron mobilities and thus the key figure of merit μC*. Nevertheless, few reports in OECTs have specially proposed to address this issue. Herein, we report a 10-ring-fused polycyclic π-system consisting of the core of naphthalene bis-isatin dimer and the terminal moieties of rhodanine, which features intramolecular noncovalent interactions, high π-delocalization and strong electron-deficient characteristics. We find that this extended π-conjugated system using the ring fusion strategy displays improved electron mobilities up to 0.043 cm²  V^-1  s^-1 compared to our previously reported small molecule gNR, and thereby leads to a remarkable μC* of 10.3 F cm^-1  V^-1  s^-1 in n-type OECTs, which is the highest value reported to date for small-molecule OECTs. This work highlights the importance of π-conjugation extension in polycyclic-fused molecules for enhancing the performance of n-type small-molecule OECTs.

A cellulose-derived supramolecule for fast ion transport

Supramolecular frameworks have been widely synthesized for ion transport applications. However, conventional approaches of constructing ion transport pathways in supramolecular frameworks typically require complex processes and display poor scalability, high cost, and limited sustainability. Here, we report the scalable and cost-effective synthesis of an ion-conducting (e.g., Na+) cellulose-derived supramolecule (Na-CS) that features a three-dimensional, hierarchical, and crystalline structure composed of massively aligned, one-dimensional, and ångström-scale open channels. Using wood-based Na-CS as a model material, we achieve high ionic conductivities (e.g., 0.23 S/cm in 20 wt% NaOH at 25 °C) even with a highly dense microstructure, in stark contrast to conventional membranes that typically rely on large pores (e.g., submicrometers to a few micrometers) to obtain comparable ionic conductivities. This synthesis approach can be universally applied to a variety of cellulose materials beyond wood, including cotton textiles, fibers, paper, and ink, which suggests excellent potential for a number of applications such as ion-conductive membranes, ionic cables, and ionotronic devices.

Textile One-Component Organic Electrochemical Sensor for Near-Body Applications

The need for more efficient health services and the trend of a healthy lifestyle pushes the development of smart textiles. Since textiles have always been an object of everyday life, smart textiles promise an extensive user acceptance. Thereby, the manufacture of electrical components based on textile materials is of great interest for applications as biosensors. Organic electrochemical transistors (OECTs) are often used as biosensors for the detection of saline content, adrenaline, glucose, etc., in diverse body fluids. Textile-based OECTs are mostly prepared by combining a liquid electrolyte solution with two separate electro-active yarns that must be precisely arranged in a textile structure. Herein, on the other hand, a biosensor based on a textile single-component organic electrochemical transistor with a hardened electrolyte was developed by common textile technologies such as impregnation and laminating. Its working principle was demonstrated by showing that the herein-produced transistor functions similarly to a switch or an amplifier and that it is able to detect ionic analytes of a saline solution. These findings support the idea of using this new device layout of textile-based OECTs as biosensors in near-body applications, though future work must be carried out to ensure reproducibility and selectivity, and to achieve an increased level of textile integration.

Organic Mixed Ion-Electron Conductivity in Polymer Hybrid Systems

Recently, organic materials with mixed ion/electron conductivity (OMIEC) have gained significant interest among research communities all over the world. The unique ability to conduct ions and electrons in the same organic material adds to their use in next generation electrochemical, biotechnological, energy generation, energy storage, electrochromic, and sensor devices. Semiconducting conjugated polymers are well-known OMIECs due to their feasibility for both ion and electron transport in the bulk region. In this mini-review, we have shed light on conjugated polymers with ionic pendent groups, block copolymers of electronically and ionic conducting polymers, polymer electrolytes, blends of conjugated polymers with polyelectrolyte/polymer electrolytes; blends of conducting polymer with small organic molecules including conducting polymer-peptide conjugates; and blends of nonconjugated polymers as mixed conducting systems. These systems not only include the well-studied OMEIC systems, but also include some new systems where the OMEIC property has been predicted from the typical current-voltage (I-V) plots. The conduction mechanism of ions and electrons, ion-electron coupling, directionality, and dimensionality of these OMEIC materials are discussed in brief. The different properties of OMEIC materials and their applications in diverse fields like energy, electrochromic, biotechnology, sensing, and so forth are enlightened together with the perspective for future improvement of OMEIC materials.

Rational Construction of Molecular Electron-Conducting Nanowires Encapsulated in a Proton-Conducting Matrix in a Charge Transfer Salt

Insulated molecular wires have gained significant attention owing to their potential contribution in the fields of nanoelectronics and low-dimensional chemistry/physics. Based on molecular charge transfer salts, we demonstrate, for the first time, the rational construction of molecular electron-conducting wires encapsulated in a proton-conducting matrix, which possibly paves the way to ionoelectronics. As expected from the molecular structure of the newly designed complex anion (i.e., propeller-shaped structure with hydrogen-bonding sites at four edges), a three-dimensional hydrogen-bonded framework was constructed within the crystal, which contains a one-dimensional array of an electron donor, tetrathiafulvalene (TTF). From the single-crystal crystallographic and spectroscopic studies, it was clarified that the nonstoichiometric deprotonation of anions and partial oxidation of TTFs occur, whereas the anion is electronically inert. Moderate conductivities of electron and proton were confirmed by dc and ac conductivity measurements. In addition, the electronic isolation of TTF wires was confirmed by the magnetic susceptibility data.

Exploiting mixed conducting polymers in organic and bioelectronic devices

Efficient transport of both ionic and electronic charges in conjugated polymers (CPs) has enabled a wide range of novel electrochemical devices spanning applications from energy storage to bioelectronic devices. In this Perspective, we provide an overview of the fundamental physical processes which underlie the operation of mixed conducting polymer (MCP) devices. While charge injection and transport have been studied extensively in both ionic and electronic conductors, translating these principles to mixed conducting systems proves challenging due to the complex relationships among the individual materials properties. We break down the process of electrochemical (de)doping, the basic feature exploited in mixed conducting devices, into its key steps, highlighting recent advances in the study of these physical processes in the context of MCPs. Furthermore, we identify remaining challenges in further extending fundamental understanding of MCP-based device operation. Ultimately, a deeper understanding of the elementary processes governing operation in MCPs will drive the advancement in both materials design and device performance.

Fabrication of Curli Fiber-PEDOT:PSS Biomaterials with Tunable Self-Healing, Mechanical, and Electrical Properties

Poly(3,4-ethylenedioxythiophene) polystyrenesulfonate (PEDOT:PSS) is a highly conductive, easily processable, self-healing polymer. It has been shown to be useful in bioelectronic applications, for instance, as a biointerfacing layer for studying brain activity, in biosensitive transistors, and in wearable biosensors. A green and biofriendly method for improving the mechanical properties, biocompatibility, and stability of PEDOT:PSS involves mixing the polymer with a biopolymer. Via structural changes and interactions with PEDOT:PSS, biopolymers have the potential to improve the self-healing ability, flexibility, and electrical conductivity of the composite. In this work, we fabricated novel protein-polymer multifunctional composites by mixing PEDOT:PSS with genetically programmable amyloid curli fibers produced byEscherichia coli bacteria. Curli fibers are among the stiffest protein polymers and, once isolated from bacterial biofilms, can form plastic-like thin films that heal with the addition of water. Curli-PEDOT:PSS composites containing 60% curli fibers exhibited a conductivity 4.5-fold higher than that of pristine PEDOT:PSS. The curli fibers imbued the biocomposites with an immediate water-induced self-healing ability. Further, the addition of curli fibers lowered the Young's and shear moduli of the composites, improving their compatibility for tissue-interfacing applications. Lastly, we showed that genetically engineered fluorescent curli fibers retained their ability to fluoresce within curli-PEDOT:PSS composites. Curli fibers thus allow to modulate a range of properties in conductive PEDOT:PSS composites, broadening the applications of this polymer in biointerfaces and bioelectronics.

Structure-Transport Properties Governing the Interplay in Humidity-Dependent Mixed Ionic and Electronic Conduction of Conjugated Polyelectrolytes

Polymeric mixed ionic-electronic conductors (MIECs) are of broad interest in the field of energy storage and conversion, optoelectronics, and bioelectronics. A class of polymeric MIECs are conjugated polyelectrolytes (CPEs), which possess a π-conjugated backbone imparting electronic transport characteristics along with side chains composed of a pendant ionic group to allow for ionic transport. Here, our study focuses on the humidity-dependent structure-transport properties of poly[3-(potassium-n-alkanoate) thiophene-2,5-diyl] (P3KnT) CPEs with varied side-chain lengths of n = 4-7. UV-vis spectroscopy along with electronic paramagnetic resonance (EPR) spectroscopy reveals that the infiltration of water leads to a hydrated, self-doped state that allows for electronic transport. The resulting humidity-dependent ionic conductivity (σ_i) of the thin films shows a monotonic increase with relative humidity (RH) while electronic conductivity (σ_e) follows a non-monotonic profile. The values of σ_e continue to rise with increasing RH reaching a local maximum after which σ_e begins to decrease. P3KnTs with higher n values demonstrate greater resiliency to increasing RH before suffering a decrease in σ_e. This drop in σ_e is attributed to two factors. First, disruption of the locally ordered π-stacked domains observed through in situ humidity-dependent grazing incidence wide-angle X-ray scattering (GIWAXS) experiments can account for some of the decrease in σ_e. A second and more dominant factor is attributed to the swelling of the amorphous domains where electronic transport pathways connecting ordered domains are impeded. P3K7T is most resilient to swelling (based on ellipsometry and water uptake measurements) where sufficient hydration allows for high σ_i (1.0 × 10^-1 S/cm at 95% RH) while not substantially disrupting σ_e (1.7 × 10^-2 S/cm at 85% RH and 8.0 × 10^-3 S/cm at 95% RH). Overall, our study highlights the complexity of balancing electronic and ionic transport in hydrated CPEs.

Propylene and butylene glycol: new alternatives to ethylene glycol in conjugated polymers for bioelectronic applications

To date, many of the high-performance conjugated polymers employed as OECT channel materials make use of ethylene glycol (EG) chains to confer the materials with mixed ionic-electronic conduction properties, with limited emphasis placed on alternative hydrophilic moieties. While a degree of hydrophilicity is required to facilitate some ionic conduction in hydrated channels, an excess results in excessive swelling, with potentially detrimental effects on charge transport. This is therefore a subtle balance that must be optimised to maximise electrical performance. Herein a series of polymers based on a bithiophene-thienothiophene conjugated backbone was synthesised and the conventional EG chains substituted by their propylene and butylene counterparts. Specifically, the use of propylene and butylene chains was found to afford polymers with a more hydrophobic character, thereby reducing excessive water uptake during OECT operation and in turn significantly boosting the polymers' electronic charge carrier mobility. Despite the polymers' lower water uptake, the newly developed oligoether chains retained sufficiently high degrees of hydrophilicity to enable bulk volumetric doping, ultimately resulting in the development of polymers with superior OECT performance.

Plant Bioelectronics and Biohybrids: The Growing Contribution of Organic Electronic and Carbon-Based Materials

Life in our planet is highly dependent on plants as they are the primary source of food, regulators of the atmosphere, and providers of a variety of materials. In this work, we review the progress on bioelectronic devices for plants and biohybrid systems based on plants, therefore discussing advancements that view plants either from a biological or a technological perspective, respectively. We give an overview on wearable and implantable bioelectronic devices for monitoring and modulating plant physiology that can be used as tools in basic plant science or find application in agriculture. Furthermore, we discuss plant-wearable devices for monitoring a plant's microenvironment that will enable optimization of growth conditions. The review then covers plant biohybrid systems where plants are an integral part of devices or are converted to devices upon functionalization with smart materials, including self-organized electronics, plant nanobionics, and energy applications. The review focuses on advancements based on organic electronic and carbon-based materials and discusses opportunities, challenges, as well as future steps.

The effect of crosslinking on ion transport in nanocellulose-based membranes

Ion selective membranes are at the heart of energy conversion and harvesting, water treatment, and biotechnologies. The currently available membranes are mostly based on expensive and non-biodegradable polymers. Here, we report a cation-selective and low-cost membrane prepared from renewable nanocellulose and 1,2,3,4-butanetetracarboxylic acid which simultaneously serves as crosslinker and source of anionic surface groups. Charge density and structure of the membranes are studied. By using different degrees of crosslinking, simultaneous control over both the nanochannel structure and surface charge concentration is achieved, which in turn determines the resulting ion transport properties. Increasing negative charge concentration via higher crosslinker content, the obtained ion conductivity reaches up to 8 mS/cm (0.1 M KCl). Optimal ion selectivity, also influenced by the solution pH, is achieved at 20 wt% crosslinker addition (with ion conductivity of 1.6 mS/cm). As regular ~1.4 nm nanochannels were formed at this composition, nanofluidic contribution to ion transport is likely.

Intrinsically Stretchable Block Copolymer Based on PEDOT:PSS for Improved Performance in Bioelectronic Applications

The conductive polyelectrolyte complex poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is ubiquitous in research dealing with organic electronic devices (e.g., solar cells, wearable and implantable sensors, and electrochemical transistors). In many bioelectronic applications, the applicability of commercially available formulations of PEDOT:PSS (e.g., Clevios) is limited by its poor mechanical properties. Additives can be used to increase the compliance but pose a risk of leaching, which can result in device failure and increased toxicity (in biological settings). Thus, to increase the mechanical compliance of PEDOT:PSS without additives, we synthesized a library of intrinsically stretchable block copolymers. In particular, controlled radical polymerization using a reversible addition-fragmentation transfer process was used to generate block copolymers consisting of a block of PSS (of fixed length) appended to varying blocks of poly(poly(ethylene glycol) methyl ether acrylate) (PPEGMEA). These block copolymers (PSS₍₁₎-b-PPEGMEA_(x), where x ranges from 1 to 6) were used as scaffolds for oxidative polymerization of PEDOT. By increasing the lengths of the PPEGMEA segments on the PEDOT:[PSS₍₁₎-b-PPEGMEA_(1-6)] block copolymers, ("Block-1" to "Block-6"), or by blending these copolymers with PEDOT:PSS, the mechanical and electronic properties of the polymer can be tuned. Our results indicate that the polymer with the longest block of PPEGMEA, Block-6, had the highest fracture strain (75%) and lowest elastic modulus (9.7 MPa), though at the expense of conductivity (0.01 S cm^-1). However, blending Block-6 with PEDOT:PSS to compensate for the insulating nature of the PPEGMEA resulted in increased conductivity [2.14 S cm^-1 for Blend-6 (2:1)]. Finally, we showed that Block-6 outperforms a commercial formulation of PEDOT:PSS as a dry electrode for surface electromyography due to its favorable mechanical properties and better adhesion to skin.

Ion Diffusion through Nanocellulose Membranes: Molecular Dynamics Study

One of the most promising applications of nanocellulose is for membranes for energy storage devices including supercapacitors, batteries, and fuel cells. Several recent studies reported the fabrication of cellulose-based membranes where ionic conductivity was confined to channels. So far, theoretical understanding of the effect of the nanoconfinement and surface charged groups on the diffusion coefficient of ions in cellulose nanochannels is missing. In the present study, we perform atomistic molecular dynamics simulations to provide this theoretical understanding and unravel mechanisms affecting the ionic diffusion in nanochannels. We demonstrate that the diffusion coefficient of ions in cellulose nanochannels is reduced in comparison to its bulk value. The change of the diffusion coefficient depends on the density of charged surface groups in nanochannels and the channel height, and it is primarily caused by the Coulomb interaction between the ions and the surface. We believe that our results reveal an important structure/property relationship in cellulose nanochannels, and they show that accounting for the dependence of the diffusion coefficient on the charge of the surface groups and channel height can be important for the Nernst-Plank-Poisson modeling of the ion conductivity in nanomembranes as well as for accurate fitting the experimental data to extract the material parameters.

Biohybrid plants with electronic roots via in vivo polymerization of conjugated oligomers

Plant processes, ranging from photosynthesis through production of biomaterials to environmental sensing and adaptation, can be used in technology via integration of functional materials and devices. Previously, plants with integrated organic electronic devices and circuits distributed in their vascular tissue and organs have been demonstrated. To circumvent biological barriers, and thereby access the internal tissue, plant cuttings were used, which resulted in biohybrids with limited lifetime and use. Here, we report intact plants with electronic functionality that continue to grow and develop enabling plant-biohybrid systems that fully maintain their biological processes. The biocatalytic machinery of the plant cell wall was leveraged to seamlessly integrate conductors with mixed ionic-electronic conductivity along the root system of the plants. Cell wall peroxidases catalyzed ETE-S polymerization while the plant tissue served as the template, organizing the polymer in a favorable manner. The conductivity of the resulting p(ETE-S) roots reached the order of 10 S cm^-1 and remained stable over the course of 4 weeks while the roots continued to grow. The p(ETE-S) roots were used to build supercapacitors that outperform previous plant-biohybrid charge storage demonstrations. Plants were not affected by the electronic functionalization but adapted to this new hybrid state by developing a more complex root system. Biohybrid plants with electronic roots pave the way for autonomous systems with potential applications in energy, sensing and robotics.

Thiophene- and selenophene-based conjugated polymeric mixed ionic/electronic conductors

Mixed ionic/electronic conductors (MIECs) are desirable materials for next-generation electronic devices and energy storage applications. Polymeric MIECs are attractive from the standpoint that their structure can be controlled and anticipated to have mechanically robust properties. Here, we prepare and investigate conjugated copolymers containing thiophene and selenophene repeat units and their homopolymer counterparts. Specifically, thiophene bearing a triethylene glycol (EG₃) side chain was polymerized and copolymerized with dodecyl thiophene/selenophene monomers. The synthesis leads to a class of copolymers that contain either S or Se and are blocky in nature. The Li-ion conductivity of ionically doped copolymers, P3DDT-s-P3(EG₃)T and P3DDS-s-P3(EG₃)T (9.7 × 10^-6 and 8.2 × 10^-6 S/cm, respectively), was 3-4 fold higher than that of the ionically doped constituent homopolymer, P3(EG₃)T (2.2 × 10^-6 S/cm), at ambient conditions. The electronic conductivity of the oxidatively doped copolymers was significantly higher than that of the constituent homopolymer P3(EG₃)T, and most notably, P3DDS-s-P3(EG₃)T reached ∼7 S/cm, which is the same order of magnitude as poly(3-dodecylthiophene) and poly(3-dodecylselenophene), which are the highest oxidatively doped conductors based on control experiments. Our findings provide implications for designing new MIECs based on copolymerization and the incorporation of heavy atom heterocycles.

Current-Driven Organic Electrochemical Transistors for Monitoring Cell Layer Integrity with Enhanced Sensitivity

In this progress report an overview is given on the use of the organic electrochemical transistor (OECT) as a biosensor for impedance sensing of cell layers. The transient OECT current can be used to detect changes in the impedance of the cell layer, as shown by Jimison et al. To circumvent the application of a high gate bias and preventing electrolysis of the electrolyte, in case of small impedance variations, an alternative measuring technique based on an OECT in a current-driven configuration is developed. The ion-sensitivity is larger than 1200 mV V-1 dec-1 at low operating voltage. It can be even further enhanced using an OECT based complementary amplifier, which consists of a p-type and an n-type OECT connected in series, as known from digital electronics. The monitoring of cell layer integrity and irreversible disruption of barrier function with the current-driven OECT is demonstrated for an epithelial Caco-2 cell layer, showing the enhanced ion-sensitivity as compared to the standard OECT configuration. As a state-of-the-art application of the current-driven OECT, the in situ monitoring of reversible tight junction modulation under the effect of drug additives, like poly-l-lysine, is discussed. This shows its potential for in vitro and even in vivo toxicological and drug delivery studies.

The Martini Model in Materials Science

The Martini model, a coarse-grained force field initially developed with biomolecular simulations in mind, has found an increasing number of applications in the field of soft materials science. The model's underlying building block principle does not pose restrictions on its application beyond biomolecular systems. Here, the main applications to date of the Martini model in materials science are highlighted, and a perspective for the future developments in this field is given, particularly in light of recent developments such as the new version of the model, Martini 3.

Fiber-Shaped Triboiontronic Electrochemical Transistor

Contact electrification-activated triboelectric potential offers an efficient route to tuning the transport properties in semiconductor devices through electrolyte dielectrics, i.e., triboiontronics. Organic electrochemical transistors (OECTs) make more effective use of ion injection in the electrolyte dielectrics by changing the doping state of the semiconductor channel. However, the mainstream flexible/wearable electronics and OECT-based devices are usually modulated by electrical signals and constructed in conventional geometry, which lack direct and efficient interaction between the external environment and functional electronic devices. Here, we demonstrate a fiber-shaped triboiontronic electrochemical transistor with good electrical performances, including a current on/off ratio as high as ≈1286 with off-current at ~nA level, the average threshold displacements (D_th) of 0.3 mm, the subthreshold swing corresponding to displacement (SS_D) at 1.6 mm/dec, and excellent flexibility and durability. The proposed triboiontronic electrochemical transistor has great potential to be used in flexible, functional, and smart self-powered electronic textile.

PEDOT:PSS nano-particles in aqueous media: A comparative experimental and molecular dynamics study of particle size, morphology and z-potential

PEDOT

PSS is the most widely used conducting polymer in organic and printed electronics.

PEDOT

PSS films have been extensively studied to understand the morphology, ionic and electronic conductivity of the polymer. However, the polymer dispersion, which is used to cast or spin coat the films, is not well characterized and not well understood theoretically. Here, we study in detail the particle morphology, size, charge density and zeta potential (z-potential) by coarse-grained MD simulations and dynamic light scattering (DLS) measurements, for different pH levels and ionic strengths. The PEDOT:PSS particles were found to be 12 nm-19 nm in diameter and had a z-potential of -30 mV to -50 mV when pH was changed from 1.7 to 9, at an added NaCl concentration of 1 mM, as measured by DLS. These values changed significantly with changing pH and ionic strength of the solution. The charge density of PEDOT:PSS particles was also found to be dependent on pH and ionic strength. Besides, the distribution of different ions (PSS^-, PEDOT⁺, Na⁺, Cl^-) present in the solution is simulated to understand the particle morphology and molecular origin of z-potential in PEDOT:PSS dispersion. The trend in change of particle size, charge density and z- potential with changing pH and ionic strength are in good agreement between the simulations and experiments. Our results show that the molecular model developed in this work represents very well the PEDOT:PSS nano-particles in aqueous dispersion. With this study, we hope to provide new insight and an in-depth understanding of the morphology and z-potential evolution in PEDOT:PSS dispersion.

Nanocellulose/Fullerene Hybrid Films Assembled at the Air/Water Interface as Promising Functional Materials for Photo-electrocatalysis

Cellulose nanomaterials have been widely investigated in the last decade, unveiling attractive properties for emerging applications. The ability of sulfated cellulose nanocrystals (CNCs) to guide the supramolecular organization of amphiphilic fullerene derivatives at the air/water interface has been recently highlighted. Here, we further investigated the assembly of Langmuir hybrid films that are based on the electrostatic interaction between cationic fulleropyrrolidines deposited at the air/water interface and anionic CNCs dispersed in the subphase, assessing the influence of additional negatively charged species that are dissolved in the water phase. By means of isotherm acquisition and spectroscopic measurements, we demonstrated that a tetra-sulfonated porphyrin, which was introduced in the subphase as anionic competitor, strongly inhibited the binding of CNCs to the floating fullerene layer. Nevertheless, despite the strong inhibition by anionic molecules, the mutual interaction between fulleropyrrolidines at the interface and the CNCs led to the assembly of robust hybrid films, which could be efficiently transferred onto solid substrates. Interestingly, ITO-electrodes that were modified with five-layer hybrid films exhibited enhanced electrical capacitance and produced anodic photocurrents at 0.4 V vs Ag/AgCl, whose intensity (230 nA/cm2) proved to be four times higher than the one that was observed with the sole fullerene derivative (60 nA/cm2).

Green Conducting Cellulose Yarns for Machine-Sewn Electronic Textiles

The emergence of "green" electronics is a response to the pressing global situation where conventional electronics contribute to resource depletion and a global build-up of waste. For wearable applications, green electronic textile (e-textile) materials present an opportunity to unobtrusively incorporate sensing, energy harvesting, and other functionality into the clothes we wear. Here, we demonstrate electrically conducting wood-based yarns produced by a roll-to-roll coating process with an ink based on the biocompatible polymer:polyelectrolyte complex poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS). The developed e-textile yarns display a, for cellulose yarns, record-high bulk conductivity of 36 Scm-1, which could be further increased to 181 Scm-1 by adding silver nanowires. The PEDOT:PSS-coated yarn could be machine washed at least five times without loss in conductivity. We demonstrate the electrochemical functionality of the yarn through incorporation into organic electrochemical transistors (OECTs). Moreover, by using a household sewing machine, we have manufactured an out-of-plane thermoelectric textile device, which can produce 0.2 μW at a temperature gradient of 37 K.

Organic Electrochemical Transistors (OECTs) Toward Flexible and Wearable Bioelectronics

Organic electronics have emerged as a fascinating area of research and technology in the past two decades and are anticipated to replace classic inorganic semiconductors in many applications. Research on organic light-emitting diodes, organic photovoltaics, and organic thin-film transistors is already in an advanced stage, and the derived devices are commercially available. A more recent case is the organic electrochemical transistors (OECTs), whose core component is a conductive polymer in contact with ions and solvent molecules of an electrolyte, thus allowing it to simultaneously regulate electron and ion transport. OECTs are very effective in ion-to-electron transduction and sensor signal amplification. The use of synthetically tunable, biocompatible, and depositable organic materials in OECTs makes them specially interesting for biological applications and printable devices. In this review, we provide an overview of the history of OECTs, their physical characterization, and their operation mechanism. We analyze OECT performance improvements obtained by geometry design and active material selection (i.e., conductive polymers and small molecules) and conclude with their broad range of applications from biological sensors to wearable devices.

High Thermoelectric Performance in n-Type Perylene Bisimide Induced by the Soret Effect

Low-cost, non-toxic, abundant organic thermoelectric materials are currently under investigation for use as potential alternatives for the production of electricity from waste heat. While organic conductors reach electrical conductivities as high as their inorganic counterparts, they suffer from an overall low thermoelectric figure of merit (ZT) due to their small Seebeck coefficient. Moreover, the lack of efficient n-type organic materials still represents a major challenge when trying to fabricate efficient organic thermoelectric modules. Here, a novel strategy is proposed both to increase the Seebeck coefficient and achieve the highest thermoelectric efficiency for n-type organic thermoelectrics to date. An organic mixed ion-electron n-type conductor based on highly crystalline and reduced perylene bisimide is developed. Quasi-frozen ionic carriers yield a large ionic Seebeck coefficient of -3021 μV K^-1 , while the electronic carriers dominate the electrical conductivity which is as high as 0.18 S cm^-1 at 60% relative humidity. The overall power factor is remarkably high (165 μW m^-1 K^-2 ), with a ZT = 0.23 at room temperature. The resulting single leg thermoelectric generators display a high quasi-constant power output. This work paves the way for the design and development of efficient organic thermoelectrics by the rational control of the mobility of the electronic and ionic carriers.

Realizing Saturable Absorption and Reverse Saturable Absorption in a PEDOT:PSS Film via Electrical Modulation

Electrical tuning of the nonlinear absorption of materials has promising application potential, while studies remain rare. In this work, we show that the third-order nonlinear absorption of poly(3,4-ethylenedioxythiophene) chemically doped with poly(styrene sulfonic acid) [PEDOT:PSS] can be effectively modulated by external voltage. The nonlinear absorption of the film can be varied between reverse saturable absorption (RSA) and saturable absorption (SA) via voltage control with laser excitation at 800 nm, and the corresponding nonlinear absorption coefficient can be tuned in the range -1606 ± 73 to 521 ± 9 cm GW^-1. The doping level and energy structure of PEDOT are modulated with different voltages. The undoped film affords two-photon absorption and accordingly the RSA response. A moderately doped sample has two polaron levels, and Pauli blocking associated with these two polaron levels results in SA. The bipolaron level in heavily doped PEDOT leads to excited-state absorption and therefore RSA behavior. The approach reported here can be applied to other semiconductors and is a convenient, effective, and promising method for the electrical tuning of the optical nonlinearity.

Devising Materials Manufacturing Toward Lab-to-Fab Translation of Flexible Electronics

Flexible electronics have witnessed exciting progress in academia over the past decade, but most of the research outcomes have yet to be translated into products or gain much market share. For mass production and commercialization, industrial adoption of newly developed functional materials and fabrication techniques is a prerequisite. However, due to the disparate features of academic laboratories and industrial plants, translating materials and manufacturing technologies from labs to fabs is notoriously difficult. Therefore, herein, key challenges in the materials manufacturing of flexible electronics are identified and discussed for its lab-to-fab translation, along the four stages in product manufacturing: design, materials supply, processing, and integration. Perspectives on industry-oriented strategies to overcome some of these obstacles are also proposed. Priorities for action are outlined, including standardization, iteration between basic and applied research, and adoption of smart manufacturing. With concerted efforts from academia and industry, flexible electronics will bring a bigger impact to society as promised.

Mixed Ionic-Electronic Conductors Based on PEDOT:PolyDADMA and Organic Ionic Plastic Crystals

Mixed ionic-electronic conductors, such as poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) are postulated to be the next generation materials in energy storage and electronic devices. Although many studies have aimed to enhance the electronic conductivity and mechanical properties of these materials, there has been little focus on ionic conductivity. In this work, blends based on PEDOT stabilized by the polyelectrolyte poly(diallyldimethylammonium) (PolyDADMA X) are reported, where the X anion is either chloride (Cl), bis(fluorosulfonyl)imide (FSI), bis(trifluoromethylsulfonyl)imide (TFSI), triflate (CF3SO3) or tosylate (Tos). Electronic conductivity values of 0.6 S cm-1 were achieved in films of PEDOT:PolyDADMA FSI (without any post-treatment), with an ionic conductivity of 5 × 10-6 S cm-1 at 70 °C. Organic ionic plastic crystals (OIPCs) based on the cation N-ethyl-N-methylpyrrolidinium (C2mpyr+) with similar anions were added to synergistically enhance both electronic and ionic conductivities. PEDOT:PolyDADMA X / [C2mpyr][X] composites (80/20 wt%) resulted in higher ionic conductivity values (e.g., 2 × 10-5 S cm-1 at 70 °C for PEDOT:PolyDADMA FSI/[C2mpyr][FSI]) and improved electrochemical performance versus the neat PEDOT:PolyDADMA X with no OIPC. Herein, new materials are presented and discussed including new PEDOT:PolyDADMA and organic ionic plastic crystal blends highlighting their promising properties for energy storage applications.

Biomorphic structural batteries for robotics

Batteries with conformal shape and multiple functionalities could provide new degrees of freedom in the design of robotic devices. For example, the ability to provide both load bearing and energy storage can increase the payload and extend the operational range for robots. However, realizing these kinds of structural power devices requires the development of materials with suitable mechanical and ion transport properties. Here, we report biomimetic aramid nanofibers–based composites with cartilage-like nanoscale morphology that display an unusual combination of mechanical and ion transport properties. Ion-conducting membranes from these aramid nanofiber composites enable pliable zinc-air batteries with cyclic performance exceeding 100 hours that can also serve as protective covers in various robots including soft and flexible miniaturized robots. The unique properties of the aramid ion conductors are attributed to the percolating network architecture of nanofibers with high connectivity and strong nanoscale filaments designed using a graph theory of composite architecture when the continuous aramid filaments are denoted as edges and intersections are denoted as nodes. The total capacity of these body-integrated structural batteries is 72 times greater compared with a stand-alone Li-ion battery with the same volume. These materials and their graph theory description enable a new generation of robotic devices, body prosthetics, and flexible and soft robotics with nature-inspired distributed energy storage.

Oxidative Spin-Spray-Assembled Coordinative Multilayers as Platforms for Capacitive Films

The spin-spray-assisted layer-by-layer (LbL) assembly technique was used to prepare coordinative oxidative multilayers from Ce(IV), inorganic polyphosphate (PP), and graphene oxide (GO). The films consist of successive tetralayers and have a general structure (PP/Ce/GO/Ce)n. Such oxidative multilayers have been shown to be a general platform for the electrodeless generation of conducting polymer and melanin-type films. Although the incorporation of GO enhances the film growth, the conventional dip LbL method is very time consuming. We show that the spin-spray method reduces the time required to grow thick multilayers by the order of magnitude and the film growth is linear from the beginning, which implies a stratified structure. We have deposited poly(3,4-ethylenedioxothiophene), PEDOT, on the oxidative multilayers and studied these redox-active films as models for melanin-type capacitive layers for supercapacitors to be used in biodegradable electronics, both before and after the electrochemical reduction of GO to rGO. The amount of oxidant and PEDOT scales linearly with the film thickness, and the charge transfer kinetics is not mass transfer-limited, especially after the reduction of GO. The areal capacitance of the films grows linearly with the film thickness, reaching a value of ca. 1.6 mF cm-2 with 20 tetralayers, and the specific volumetric (per film volume) and mass (per mass of PEDOT) capacitances are ca. 130 F cm-3 and 65 F g-1, respectively. 5,6-Dihydroxyindole can also be polymerized to a redox-active melanin-type film on these oxidative multilayers, with even higher areal capacitance values.

Thermal Stability of π-Conjugated n-Ethylene-Glycol-Terminated Quaterthiophene Oligomers: A Computational and Experimental Study

This work represents a joint computational and experimental study on a series of n-ethylene glycol (PEOn)-terminated quaterthiophene (4T) oligomers for 1 < n < 10 to elucidate their self-assembly behavior into a smectic-like lamellar phase. This study builds on an earlier study for n = 4 that showed that our model predictions were consistent with experimental data on the melting behavior and structure of the lamellar phase, with the latter consisting of crystal-like 4T domains and liquid-like PEO4 domains. The present study aims to understand how the length of the terminal PEOn chains modulates the disordering temperature of the lamellar phase and hence the relative stability of the ordered structure. A simplified bilayer model, where the 4T domains are not explicitly described, is put forward to efficiently estimate the disordering effect of the PEO domains with increasing n; this method is first validated by correctly predicting that layers of alkyl (PE)-capped 4T oligomers (for 1 < n < 10) stay ordered at room temperature. Both 4T-domain implicit and explicit model simulations reveal that the order-disorder temperature decreases with the length of the PEO capping chains, as the associated increase in conformational entropy drives a tendency toward disorder that overtakes the cohesive energy, keeping the ordered packing of the 4T domains.

Nitrogen Incorporated Photoactive Brownmillerite Ca2Fe2O5 for Energy and Environmental Applications

Ca₂Fe₂O₅ (CFO) is a potentially viable material for alternate energy applications. Incorporation of nitrogen in Ca₂Fe₂O₅ (CFO-N) lattice modifies the optical and electronic properties to its advantage. Here, the electronic band structures of CFO and CFO-N were probed using Ultraviolet photoelectron spectroscopy (UPS) and UV-Visible spectroscopy. The optical bandgap of CFO reduces from 2.21 eV to 2.07 eV on post N incorporation along with a clear shift in the valence band of CFO indicating the occupation of N 2p levels over O 2p in the valence band. Similar effect is also observed in the bandgap of CFO, which is tailored upto 1.43 eV by N⁺ ion implantation. The theoretical bandgaps of CFO and CFO-N were also determined by using the Density functional theory (DFT) calculations. The photoactivity of these CFO and CFO-N was explored by organic effluent degradation under sunlight. The feasibility of utilizing CFO and CFO-N samples for energy storage applications were also investigated through specific capacitance measurements. The specific capacitance of CFO is found to increase to 224.67 Fg⁻¹ upon N incorporation. CFO-N is thus found to exhibit superior optical, catalytic as well as supercapacitor properties over CFO expanding the scope of brownmillerites in energy and environmental applications.

Humidity-Controlled Water Uptake and Conductivities in Ion and Electron Mixed Conducting Polythiophene Films

Mixed conducting polymer films are of great interest in applications where an interface between electronic and ionic charge transport is needed, e.g., in bioelectronics, electrochemical energy applications, and photovoltaic device interfaces. The role of water on charge transport is of high relevance not only for aqueous environments but also for devices that are manufactured at ambient conditions with varying relative humidities. In this contribution, we present our results on the influence of controlled humidity changes on the mixed conductivity and correlation to the concomitant water uptake in the films. Two sulfonate-bearing polythiophene systems are studied: a self-made conjugated polyelectrolyte, poly(6-(thiophen-3-yl)hexane-1-sulfonate)-sodium (PTS-Na), and poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate) (PEDOT/PSS) with different ratios of PEDOT and the polyelectrolyte PSS. Our data give clear evidence of the similarities between the aforementioned polythiophene systems and pure ionic membranes such as Nafion used in fuel cells. As such, a phase separation between the hydrophobic electronically conducting polythiophene phase and the hydrophilic water-swellable ion-conducting phase is proposed. Changing the humidity from dry conditions up to ∼90% relative humidity results in extremely high water uptakes of more than 90 wt %, which corresponds to ∼13 water molecules per sulfonate unit at maximum water uptake. Conversely, the electronic conductivity is less sensitive to increasing humidity, which is due to percolation pathways. The ionic conductivity strongly increases from 10^-10 S/cm at dry conditions to 10^-3 S/cm at around 30 wt % water content and then levels off at maximum conductivities of 10^-3-10^-2 S/cm up to water contents of 90 wt %.

The intrinsic volumetric capacitance of conducting polymers: pseudo-capacitors or double-layer supercapacitors?

The capacitance of conducting polymers represents one of the most important material parameters that in many cases determines the device and material performances. Despite a vast number of experimental studies, the theoretical understanding of the origin of the capacitance in conducting polymers remains unsatisfactory and appears even controversial. Here, we present a theoretical method, based on first principle capacitance calculations using density functional theory (DFT), and apply it to calculate the volumetric capacitance of two archetypical conducting polymers: poly(3,4-ethylene dioxythiophene) (PEDOT) and polypyrrole (PPy). Our aim is to achieve a quantitate description of the volumetric capacitance and to provide a qualitative understanding of its nature at the atomistic level. We find that the volumetric capacitance of PEDOT and PPy is ≈100 F cm-3 and ≈300 F cm-3, respectively, which is within the range of the corresponding reported experimental results. We demonstrate that the capacitance of conducting polymers originates from charges stored in atomistic Stern layers formed by counterions and doped polymeric chains. The Stern layers have a purely electrostatic origin, since the counterions do not form any bonds with the atoms of the polymeric chains, and no charge transfer between the counterions and conducting polymer takes place. This classifies the conducting polymers as double-layer supercapacitors rather than pseudo-capacitors. Further, we analyze contributions to the total capacitance originating from the classical capacitance C C and the quantum capacitance C Q, respectively, and find that the latter provides a dominant contribution. The method of calculations of the capacitance developed in the present paper is rather general and opens up the way for engineering and optimizing the capacitive response of the conducting polymers.

Multifunctional Nanocomposites with High Strength and Capacitance Using 2D MXene and 1D Nanocellulose

The family of two-dimensional (2D) metal carbides and nitrides, known as MXenes, are among the most promising electrode materials for supercapacitors thanks to their high metal-like electrical conductivity and surface-functional-group-enabled pseudocapacitance. A major drawback of these materials is, however, the low mechanical strength, which prevents their applications in lightweight, flexible electronics. A strategy of assembling freestanding and mechanically robust MXene (Ti₃ C₂ T_x ) nanocomposites with one-dimensional (1D) cellulose nanofibrils (CNFs) from their stable colloidal dispersions is reported. The high aspect ratio of CNF (width of ≈3.5 nm and length reaching tens of micrometers) and their special interactions with MXene enable nanocomposites with high mechanical strength without sacrificing electrochemical performance. CNF loading up to 20%, for example, shows a remarkably high mechanical strength of 341 MPa (an order of magnitude higher than pristine MXene films of 29 MPa) while still maintaining a high capacitance of 298 F g^-1 and a high conductivity of 295 S cm^-1 . It is also demonstrated that MXene/CNF hybrid dispersions can be used as inks to print flexible micro-supercapacitors with precise dimensions. This work paves the way for fabrication of robust multifunctional MXene nanocomposites for printed and lightweight structural devices.

Layer-by-Layer Assembly of High-Performance Electroactive Composites Using a Multiple Charged Small Molecule

Layer-by-layer (LbL) assembly is a versatile tool for fabricating multilayers with tailorable nanostructures. LbL, however, generally relies on polyelectrolytes, which are mostly insulating and induce large interlayer distances. We demonstrate a method in which we replace polyelectrolytes with the smallest unit capable of LbL self-assembly: a molecule with multiple positive charges, tris(3-aminopropyl)amine (TAPA), to fabricate LbL films with negatively charged single-walled carbon nanotubes (CNTs). TAPA introduces less defects during the LbL build-up and results in more efficient assembly of films with denser micromorphology. Twenty bilayers of TAPA/CNT showed a low sheet resistance of 11 kΩ, a high transparency of 91% at 500 nm, and a high electronic conductivity of 1100 S/m on planar substrates. We also fabricated LbL films on porous foams with a conductivity of 69 mS/m and used them as electrodes for supercapacitors with a high specific capacitance of 43 F/g at a discharging current density of 1 A/g.