Defects on CoS 2− x : Tuning Redox Reactions for Sustainable Degradation of Organic Pollutants

Nickel-doped red mud-based Prussian blue analogues heterogeneous activation of H2O2 for ciprofloxacin degradation: waste control by waste

Red mud (RM) is a typical bulk solid waste with Fe/Al/Si/Ca-rich characteristics that has been used to prepare various heterogeneous catalysts such as iron-based catalysts and supported catalysts. Prussian blue analogues (PBA) is a low-cost, environmentally friendly, and active site rich iron-based metal organic framework, but its catalytic properties are adversely affected by their easy aggregation. In this study, nickel-doped RM-based PBA (RM-Ni PBA) was synthesized by acid dissolution-coprecipitation method for the degradation of ciprofloxacin (CIP). The characterization showed that RM-Ni PBA was a material with excellent dispersibility, large specific surface area, and abundant active sites. The degradation results showed that the removal efficiency of CIP in the RM-Ni PBA/H2O2 system was 16.63, 1.78, and 1.81 times that of RM, RM-PB, and Ni PBA, respectively. It was found that 1O2 was the main reactive oxygen species (ROS) dominated the degradation process, and its formation was accompanied by the mutual conversion of Ni(II)/Fe(II) and Ni(III)/Fe(III). Notably, the degradation process maintained a satisfactory efficiency over a wide pH range (3-9) and exhibited strong anti-interference ability against impurities such as Cl-, SO42-, and NO3-. The components and contents of RM-Ni PBA remained relatively stable during the degradation process. In addition, the degradation intermediates of CIP were identified, and possible degradation pathways were proposed. This study is expected to provide theoretical basis and technical guidance for the application of RM-based heterogeneous catalyst in the treatment of antibiotic wastewater.

A systematic review on percarbonate-based advanced oxidation processes in wastewater remediation: From theoretical understandings to practical applications

Percarbonate encompasses sodium percarbonate (SPC) and composite in-situ generated peroxymonocarbonate (PMC). SPC emerges as a promising alternative to hydrogen peroxide (H2O2), hailed for its superior transportation safety, stability, cost-effectiveness, and eco-friendliness, thereby becoming a staple in advanced oxidation processes for mitigating water pollution. Yet, scholarly literature scarcely explores the deployment of percarbonate-AOPs in eradicating organic contaminants from aquatic systems. Consequently, this review endeavors to demystify the formation mechanisms and challenges associated with reactive oxygen species (ROS) in percarbonate-AOPs, alongside highlighting directions for future inquiry and development. The genesis of ROS encompasses the in situ chemical oxidation of activated SPC (including iron-based activation, discharge plasma, ozone activation, photon activation, and metal-free materials activation) and composite in situ chemical oxidation via PMC (namely, H2O2/NaHCO3/Na2CO3, peroxymonosulfate/NaHCO3/Na2CO3 systems). Moreover, the ROS generated by percarbonate-AOPs, such as •OH, O2•-, CO3•-, HO2•-, 1O2, and HCO4-, can work individually or synergistically to disintegrate target pollutants. Concurrently, this review systematically addresses conceivable obstacles posing percarbonate-AOPs in real-world application from the angle of environmental conditions (pH, temperature, coexisting substances), and potential ecological toxicity. Considering the outlined challenges and advantages, we posit future research directions to amplify the applicability and efficacy of percarbonate-AOPs in tangible settings. It is anticipated that the insights provided in this review will catalyze the progression of percarbonate-AOPs in water purification endeavors and bridge the existing knowledge void.

White light powered antimicrobial nanoagents for triple photothermal, chemodynamic and photodynamic based sterilization

Antibacterial nanoagents have been increasingly developed due to their favorable biocompatibility, cost-effective raw materials, and alternative chemical or optical properties. Nevertheless, there is still a pressing need for antibacterial nanoagents that exhibit outstanding bacteria-binding capabilities and high antibacterial efficiency. In this study, we constructed a multifunctional cascade bioreactor (GCDCO) as a novel antibacterial agent. This involved incorporating carbon dots (CDs), cobalt sulfide quantum dots (CoSx QDs), and glucose oxidase (GOx) to enhance bacterial inhibition under sunlight irradiation. The GCDCO demonstrated highly efficient antibacterial capabilities attributed to its favorable photothermal properties, photodynamic activity, as well as the synergistic effects of hyperthermia, glucose-augmented chemodynamic action, and additional photodynamic activity. Within this cascade bioreactor, CDs played the role of a photosensitizer for photodynamic therapy (PDT), capable of generating ˙O2- even under solar light irradiation. The CoSx QDs not only functioned as a catalytic component to decompose hydrogen peroxide (H2O2) and generate hydroxyl radicals (˙OH), but they also served as heat generators to enhance the Fenton-like catalysis process. Furthermore, GOx was incorporated into this cascade bioreactor to internally supply H2O2 by consuming glucose for a Fenton-like reaction. As a result, GCDCO could generate a substantial amount of reactive oxygen species (ROS), leading to a significant synergistic effect that greatly induced bacterial death. Furthermore, the in vitro antibacterial experiment revealed that GCDCO displayed notably enhanced antibacterial activity against E. coli (99+ %) when combined with glucose under simulated sunlight, surpassing the efficacy of the individual components. This underscores its remarkable efficiency in combating bacterial growth. Taken together, our GCDCO demonstrates significant potential for use in the routine treatment of skin infections among diabetic patients.

Enhancing singlet oxygen production of dioxygen activation on the carbon-supported rare-earth oxide nanocluster and rare-earth single atom catalyst to remove antibiotics

Singlet oxygen (1O2) is extensively employed in the fields of chemical, biomedical and environmental. However, it is still a challenge to produce high- concentration 1O2 by dioxygen activation. Herein, a system of carbon-supported rare-earth oxide nanocluster and single atom catalysts (named as RE2O3/RE-C, RE=La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu, Sc and Y) with similar morphology, structure, and physicochemical characteristic are constructed to activate dissolved oxygen (DO) to enhance 1O2 production. The catalytic activity trends and mechanisms are revealed experimentally and are also proven by theoretical analyses and calculations. The 1O2 generation activity trend is Gd2O3/Gd-C>Er2O3/Er-C>Sm2O3/Sm-C>pristine carbon (C). More than 95.0% of common antibiotics (ciprofloxacin, ofloxacin, norfloxacin and carbamazepine) can be removed in 60 min by Gd2O3/Gd-C. Density functional theory calculations indicate that Gd2O3 nanoclusters and Gd single atoms exhibit the moderate adsorption energy of ·O2- to enhance 1O2 production. This study offers a universal strategy to enhance 1O2 production in dioxygen activation for future application and reveals the natural essence of basic mechanisms of 1O2 production via rare-earth oxide nanoclusters and rare-earth single atoms.

A Defective Disc-Like Cu1.96 S Anode Material with the Efficient Cu Vacancies for High-Performance Sodium-Ion Storage

Due to their significant capacity and reliable reversibility, transition metal sulphides (TMSs) have received attention as potential anode materials for sodium-ion batteries (SIBs). Nonetheless, a prevalent challenge with TMSs lies in their significant volume expansion and sluggish kinetics, impeding their capacity for rapid and enduring Na+ storage. Herein, a Cu1.96 S@NC nanodisc material enriched with copper vacancies is synthesised via a hydrothermal and annealing procedure. Density functional theory (DFT) calculations reveal that the incorporation of copper vacancies significantly boosts electrical conductivity by reducing the energy barrier for ion diffusion, thereby promoting efficient electron/ion transport. Moreover, the presence of copper vacancies creates ample active sites for the integration of sodium ions, streamlines charge transfer, boosts electronic conductivity, and, ultimately, significantly enhances the overall performance of SIBs. This novel anode material, Cu1.96 S@NC, demonstrates a reversible capacity of 339 mAh g-1 after 2000 cycles at a rate of 5 A g-1 . In addition, it maintains a noteworthy reversible capacity of 314 mAh g-1 with an exceptional capacity retention of 96% even after 2000 cycles at 20 A g-1 . The results demonstrate that creating cationic vacancies is a highly effective strategy for engineering anode materials with high capacity and rapid reactivity.

Palladium-Catalyzed Hydrogenation of Black Barium Titanate for Multienzyme-Piezoelectric Synergetic Tumor Therapy

Piezocatalytic tumor therapy is an emerging reactive oxygen species (ROS)-generating therapeutic approach that relies on piezoelectric polarization under ultrasound (US) irradiation. Optimizing ROS production is a primary objective for enhancing treatment efficiency. In this study, oxygen-vacancy-rich Pd-integrated black barium titanate (BTO) nanoparticles are rationally engineered to boost the ROS generation efficiency via the introduction of Pd. Pd-catalyzed hydrogenation at low temperatures narrows the bandgap of BTO and reduces the recombination rate of electron-hole pairs. Furthermore, Pd has dual-enzyme-mimicking characteristics, including peroxidase- and catalase-mimicking activities, which further heighten the therapeutic efficacy by enhancing ROS production and reversing the hypoxic tumor microenvironment. Importantly, the dual enzymatic activity of Pd can be amplified by multiple redox processes sparked by the piezoelectric potential under US stimulation, resulting in bilaterally enhanced multienzyme-piezoelectric synergetic therapy. In vitro and in vivo results confirm high tumor inhibition in murine breast cancer cells. This work stresses the critical effects of defect engineering-optimized piezodynamic tumor therapy.

Effective green treatment of sewage sludge from Fenton reactions: Utilizing MoS2 for sustainable resource recovery

Effectively managing sewage sludge from Fenton reactions in an eco-friendly way is vital for Fenton technology's viability in pollution treatment. This study focuses on sewage sludge across various treatment stages, including generation, concentration, dehydration, and landfill, and employs chemical composite MoS2 to facilitate green resource utilization of all types of sludge. MoS2, with exposed Mo4+ and low-coordination sulfur, enhances iron cycling and creates an acidic microenvironment on the sludge surface. The MoS2-modified iron sludge exhibits outstanding (>95%) phenol and pollutant degradation in hydrogen peroxide and peroxymonosulfate-based Fenton systems, unlike unmodified sludge. This modified sludge maintains excellent Fenton activity in various water conditions and with multiple anions, allowing extended phenol degradation for over 14 d. Notably, the generated chemical oxygen demand (COD) in sludge modification process can be efficiently eliminated through the Fenton reaction, ensuring effluent COD compliance and enabling eco-friendly sewage sludge resource utilization.

Satisfactory degradation of tetracycline by a pH-universal CoFe-LDH/MoS2 heterojunction catalyst in Fenton process

Fenton or Fenton-like reactions have been widely used in various fields, including solar energy conversion to generate hydroxyl radicals, environmental remediation, biology, and life science. However, the slow Fe3+/Fe2+ cycle and narrow applicable pH range still present significant challenges. Here, a heterostructured CoFe-layered double hydroxide/MoS2 nanocomposite (CoFe-LDH/MoS2) was prepared via simple electrostatic interactions. The heterostructure establishes a robust interfacial contact, leading to an abundance of exposed Mo6+ sites. Consequently, the developed CoFe-LDH/MoS2+H2O2 system exhibited superior performance in the degradation of tetracycline (>85%) within 60 min across a wide pH range from acidic to basic. Moreover, the CoFe-LDH/MoS2 heterojunction catalysts exhibited exceptional resistance to common anions and efficiently degraded various organic pollutants. The mechanism study verified that the CoFe-LDH/MoS2 had high efficiency in producing 1O2 and ‧OH to degrade various organic pollutants. The present study will serve as a foundation for creating efficient catalyst systems for related environmental remediation.

Solvent-free synthesis of foam board-like CoSe2 alloy to selectively generate singlet oxygen via peroxymonosulfate activation for sulfadiazine degradation

Singlet oxygen (1O2) is a highly effective reactive species in selectively oxidizing organic pollutants. However, it is still challenging to rationally design robust catalysts for the selective generation of 1O2. Herein, the coordination and engineering architecture of the foam board-like CoSe2 alloy were facilely constructed through a green solvent-free method and displayed almost 100% 1O2 production selectivity. The CoSe2 alloy showed excellent catalytic ability for the efficient and fast removal of organic pollutants via peroxymonosulfate (PMS) activation compared with previously reported cobalt-based catalysts. The CoSe2/PMS system exhibited strong resistance for a broad pH range (3.0-11.0) and various coexisting inorganic ions owing to the advantage of the strong bonding of Co-Se in CoSe2 alloy. Mechanism studies revealed that 1O2 was the only reactive oxygen species in the CoSe2/PMS system. Theoretical calculations demonstrated that Co was the dominant adsorption site for PMS in CoSe2, and the production pathway of 1O2 was PMS* → *OH → *O → 1O2. In addition, it was proved that *OH and *O served as the rate-determining steps for the formation of 1O2 by PMS activation on CoSe2 alloy. These findings provide a rational strategy for preparing a series of low-cost transition metal-based alloy catalysts for PMS activation to achieve high-efficiency 1O2 production in the elimination of organic pollutants.

Synthesis and Electrocatalytic Applications of Layer-Structured Metal Chalcogenides Composites

Featured with the attractive properties such as large surface area, unique atomic layer thickness, excellent electronic conductivity, and superior catalytic activity, layered metal chalcogenides (LMCs) have received considerable research attention in electrocatalytic applications. In this review, the approaches developed to synthesize LMCs-based electrocatalysts are summarized. Recent progress in LMCs-based composites for electrochemical energy conversion applications including oxygen reduction reaction, carbon dioxide reduction reaction, oxygen evolution reaction, hydrogen evolution reaction, overall water splitting, and nitrogen reduction reaction is reviewed, and the potential opportunities and practical obstacles for the development of LMCs-based composites as high-performing active substances for electrocatalytic applications are also discussed. This review may provide an inspiring guidance for developing high-performance LMCs for electrochemical energy conversion applications.

Degradation of norfloxacin by red mud-based prussian blue activating H2O2: A strategy for treating waste with waste

The massive accumulation of red mud (RM) and the abuse of antibiotics pose a threat to environment safety and human health. In this study, we synthesized RM-based Prussian blue (RM-PB) by acid solution-coprecipitation method to activate H2O2 to degrade norfloxacin, which reached about 90% degradation efficiency at pH 5 within 60 min and maintained excellent catalytic performance over a wide pH range (3-11). Due to better dispersion and unique pore properties, RM-PB exposed more active sites, thus the RM-PB/H2O2 system produced more reactive oxygen species. As a result, the removal rate of norfloxacin by RM-PB/H2O2 system was 8.58 times and 2.62 times of that by RM/H2O2 system and PB/H2O2 system, respectively. The reactive oxygen species (ROS) produced in the degradation process included ·OH, ·O2- and 1O2, with 1O2 playing a dominant role. The formation and transformation of these ROS was accompanied by the Fe(III)/Fe(II) cycle, which was conducive for the sustained production of ROS. The RM-PB/H2O2 system maintained a higher degradation efficiency after five cycles, and the material exhibited strong stability, with a low iron leaching concentration. Further research showed the degradation process was less affected by Cl-, SO42-, NO3-, and humic acids, but was inhibited by HCO3- and HPO42-. In addition, we also proposed the possible degradation pathway of norfloxacin. This work is expected to improve the resource utilization rate of RM and achieve treating waste with waste.

Performance and mechanism investigation on the enhanced photocatalytic removal of atrazine on S-doped g-C3N4

Developing efficient method for removing low-concentration atrazine, a poisonous chlorinated triazine herbicide with poor biodegradability, was an important measure to control its risk. In this work, highly efficient photocatalytic oxidation of atrazine was achieved on S-doped g-C3N4 (S-g-C3N4). Approximate 99.6% of atrazine was removed in 2 h with a reaction rate constant of 2.76 h-1, nearly 2.44 times that on g-C3N4. The mechanism investigation indicated the improved photocatalytic performance of S-g-C3N4 could be attributed to the enlarged specific surface area, extended light absorption as well as the accelerated separation of the photogenerated charge carriers, which was brought about by the successful doping of sulfur in g-C3N4. Meanwhile, the influence of sulfur doping on the generation and contribution of different reactive species in atrazine removal were also elucidated. It revealed that compared with g-C3N4, the more positive valence band potential of S-g-C3N4 was beneficial to produce more singlet oxygen, which could react synergistically with the superoxide radicals, leading to the improved atrazine removal efficiency. The S-g-C3N4 based photocatalytic system also showed preferential photocatalytic oxidation capability in removing other triazine pesticides compared with 3-chlorophenol (3-CP). The potential applicability of the S-g-C3N4 based photocatalytic system in removing atrazine in high salty water was also investigated, which exhibited superior anti-interference ability towards virous coexistent ions. This work will provide essential and fundamental information for establishing efficient photocatalytic system for triazine type pollutants in waters.

Colloid-bound radicals formed in NOM-enhanced Fe(III)/peroxymonosulfate process accelerate the degradation of trace organic contaminants in water

The omnipresence of natural organic matter (NOM) in water bodies traditionally hinders the degradation of trace organic contaminants (TrOCs) in peroxymonosulfate (PMS)-based advanced oxidation processes (AOPs). This study elucidates the positive role of NOM in enhancing the degradation of TrOCs through the Fe(III)/PMS process. During this process, NOM reduces Fe(III), yielding semiquinone-like radical (NOM•) and concurrently forming NOM-Fe(III) colloids. In addition to the Fe(II)-mediated activation pathway, Fe(III) sites on NOM-Fe(III) colloids effectively transfer electrons from NOM• or some redox-active moieties to PMS, resulting in the generation of long-lived colloid-bound SO4•-, which can readily undergo hydrolysis to produce HO•. The stabilization of SO4•- and HO• by NOM-Fe(III) colloids, combined with their moderate adsorption of TrOCs, results in surface-confined reactions that significantly enhance TrOC removal, despite the presence of concurrent quenching reactions between radicals and NOM. Further, the significant positive correlation between the phenolic contents of eight NOM types and TrOC degradation kinetics suggests phenolic moieties as the primary electron source for PMS activation. By in-situ utilizing NOM in raw water, a PMS-amended iron coagulation process with 0.2 mM Fe(III) and PMS effectively removes 90-100 % of six coexisting TrOCs. This study unveils the previously unrecognized role of colloid-bound radicals in decontamination processes, offering valuable insights into harnessing NOM's influence in advanced oxidation water treatment processes.

Application of exosomes as nanocarriers in cancer therapy

Cancer remains the most common lethal disease in the world. Although the treatment choices for cancer are still limited, significant progress has been made over the past few years. By improving targeted drug therapy, drug delivery systems promoted the therapeutic effects of anti-cancer medications. Exosome is a kind of natural nanoscale delivery system with natural substance transport properties, good biocompatibility, and high tumor targeting, which shows great potential in drug carriers, thereby providing novel strategies for cancer therapy. In this review, we present the formation, distribution, and characteristics of exosomes. Besides, extraction and isolation techniques are discussed. We focus on the recent progress and application of exosomes in cancer therapy in four aspects: exosome-mediated gene therapy, chemotherapy, photothermal therapy, and combination therapy. The current challenges and future developments of exosome-mediated cancer therapy are also discussed. Finally, the latest advances in the application of exosomes as drug delivery carriers in cancer therapy are summarized, which provide practical value and guidance for the development of cancer therapy.

New Insights into Selective Singlet Oxygen Production via the Typical Electroactivation of Oxygen for Water Decontamination

Selective production of singlet oxygen (1O2) as an electrophilic oxidant is crucial for the precise control of chemical targets in environmental fields. Herein, we proposed a strategy to construct a redox interface on electrodes, which can in situ produce inorganic metal hydroperoxides with appropriate oxidative ability during oxygen activation. Benefiting from atomic Cu sites (CuN4) in a copper-carbon aerogel electrode, almost complete production of 1O2 was achieved, thereby refraining the competitive formation of other reactive oxygen species. The fast electron transfer rate between CuN4 and electrogenerated H2O2 promoted the in situ formation of copper hydroperoxide (N4-Cu-OOH), thereby selectively and efficiently oxidizing intermediate O2•- to 1O2. The optimized production of 1O2 was up to 2583 μmol L-1 without additional chemical reagents. We further considered the high production of 1O2 for efficiently removing electron-rich organic pollutants from a complex water matrix. Fast kinetics was achieved and considered for removing various pollutants with electron-donating substituents in a nonradical oxidation pathway. The BPA degradation efficiency is less susceptible to the coexisting natural organic matter (NOM) and inorganic ions. Specifically, the kinetic constant for BPA removal is 34 times higher than that for a nanoparticle of a copper-carbon electrode while producing a hydroxyl radical. Our findings highlight the innovative interfacial surface engineering of an electrocatalytic O2 activation system to selectively generate 1O2 for future potential applications.

Vacancy-Rich CoSx@LDH@Co-NC Catalytic Membrane for Antibiotic Degradation with Mechanistic Insights

Improving the wettability of carbon-based catalysts and overcoming the rate-limiting step of the Mn+1/Mn+ cycle are effective strategies for activating peroxymonosulfate (PMS). In this study, the coupling of Co-NC, layered double hydroxide (LDH), and CoSx heterostructure (CoSx@LDH@Co-NC) was constructed to completely degrade ofloxacin (OFX) within 10 min via PMS activation. The reaction rate of 1.07 min-1 is about 1-2 orders of magnitude higher than other catalysts. The interfacial effect of confined Co-NC and layered double hydroxide (LDH) not only enhanced the wettability of catalysts but also increased the vacancy concentration; it facilitated easier contact with the interface reactive oxygen species (ROS). Simultaneously, reduced sulfur species (CoSx) accelerated the Co3+/Co2+ cycle, acquiring long-term catalytic activity. The catalytic mechanism revealed that the synergistic effect of hydroxyl groups and reduced sulfur species promoted the formation of 1O2, with a longer lifespan and a longer migration distance, and resisted the influence of nontarget background substances. Moreover, considering the convenience of practical application, the CoSx@LDH@Co-NC-based catalytic membrane was prepared, which had zero discharge of OFX and no decay in continuous operation for 5.0 h. The activity of the catalytic membrane was also verified in actual wastewater. Consequently, this work not only provides a novel strategy for designing excellent catalysts but also is applicable to practical organic wastewater treatment.

Spin state-dependent in-situ photo-Fenton-like transformation from oxygen molecule towards singlet oxygen for selective water decontamination

The development of 1O2-dominanted selective decontamination for water purification was hampered by extra H2O2 consumption and poor 1O2 generation. Herein, we proposed the reconstruction of Fe spin state using near-range N atom and long-range N vacancies to enable efficient generation of H2O2 and sequential activation of H2O2 into 1O2 after visible-light irradiation. Theoretical and experimental results revealed that medium-spin Fe(III) strengthened O2 adsorption, penetrated eg electrons to antibonding p-orbital of oxygen, and lowered the free energy of O2 activation, enabling the oxygen protonation for H2O2 generation. Thereafter, the electrons of H2O2 could be extracted by low-spin Fe(III) and rapidly converted into 1O2 in a nonradical path. The developed 1O2-dominated in-situ photo-Fenton-like system had an excellent pH universality and anti-interference to inorganic ions, dissolved organic matter, and even real water matrixes (e.g., tap water and secondary effluent). This work provided a novel insight for sustainable and efficient 1O2 generation, which motivated the development of new-generation selective water treatment technology.

Construction of a novel ferrihydrite/MoS2 heterogeneous Fenton-like catalyst for efficient degradation of organic pollutants under neutral conditions

In this work, we have fabricated a novel Fenton-like ferrihydrite/MoS2 (Fh/MoS2) composite and verified that the introduction of a small amount of iron on the surface of MoS2 can directly promote the exposure of Mo4+, finally enhancing the catalytic activity of the catalyst. Even though the content of iron element is only 1.19% in the composite, the reaction rate constant of Fh/MoS2 system for the degradation of environmental pollutants, such as organic dyes, antibiotic, and ionic liquid, is all much better than that of pure MoS2 system, which is attributed to much more generation of reactive oxygen species derived from synergistic effect of Fe3+/Fe2+ and Mo4+/Mo6+ redox cycles. The results of XPS and low-temperature EPR confirm that the exposure amount of Mo4+ active sites of 10% Fh/MoS2 is greatly increased, which is conducive to the conversion of Fe3+ to Fe2+ in the reaction process, thus effectively promoting the activation of H2O2.

Spatiotemporally and Chemically Resolved Imaging of Electrocatalytic Oxygen Evolution on Single Nanoplates of Cobalt-Layered Hydroxide

Transition metal-layered hydroxides have been extensively studied in order to address the key challenge of slow kinetics of the oxygen evolution reaction (OER). However, how the catalytically active sites are evolved and the corresponding heterogeneous structure-property relationship remain unclear. Herein, using cobalt-layered hydroxide as a representative catalyst, we report a strategy for the comprehensive in situ investigation of the electrocatalytic OER process at the single electrocatalyst level using combined electrochemiluminescence (ECL) and vis-absorption microscopy. The stepwise heterogeneous electrocatalytic responses of single-cobalt hydroxide nanoplates are unveiled with ECL imaging, and the corresponding valence state changes are revealed by vis-absorption imaging. The correlated in situ and ex situ multimode analyses indicate that, during the oxidation process, the Co2+ cations in the tetrahedral sites (CoTd2+) turned into CoTd3+ and even the highly unstable CoTd4+, assisted by the interlayer water in a metastable CoOOH·xH2O phase. Crucially, the CoTd4+ sites are mainly distributed in the inner part of the nanoplates and show superior electrocatalytic properties. The correlative single-particle imaging approach for electrocatalytic process analysis with high spatiotemporal and chemical resolution enables in-depth mechanistic insights to be generated and, in turn, will benefit the rational design of electrocatalysts with enhanced performance.

Highly active complexes of pyrite and organic matter regulate arsenic fate

Arsenic (As) presents high toxicity and strong carcinogenicity, and its health risks are regulated by its oxidation state and speciation. As can form complexes with the surface of minerals or organic matter through adsorption, affecting its toxicity and bioavailability. However, the regulation effect of the interaction of coexisting minerals and organic matter on As fate remains largely unknown. Here, we discovered that minerals (e.g., pyrite) and organic matter (e.g., alanyl glutamine, AG) can form pyrite-AG complexes, promoting As(III) oxidation under simulated solar irradiation. The formation of pyrite-AG was explored in terms of the interaction of surface oxygen atoms, electron transfer and crystal surface changes. From the perspective of atoms and molecules, pyrite-AG showed more oxygen vacancies, stronger reactive oxygen species (ROS) and a higher electron transport capacity than pyrite alone. Compared with pyrite, pyrite-AG effectively promoted the conversion of highly toxic As(III) to less toxic As(V) due to the enhanced photochemical properties. Moreover, quantification and capture of ROS confirmed that hydroxyl radicals (•OH) played an important role in As(III) oxidation in the pyrite-AG and As(III) system. Our results provide previously unidentified perspectives on the effects and chemical mechanisms of highly active complexes of mineral and organic matter on As fate and provide new insights into the risk assessment and control of As pollution.

Low-valent copper on molybdenum triggers molecular oxygen activation to selectively generate singlet oxygen for advanced oxidation processes

Singlet oxygen (¹O₂), which is difficult to generate, plays an important role in chemosynthesis, biomedicine and environment. Molecular oxygen (O₂) is a green oxidant to produce ¹O₂ cost-effectively. However, O₂ activation is difficult due to its spin-forbidden nature. Moreover, the main products of O₂ activation are basically hydrogen peroxide (H₂O₂) and hydroxyl radical (•OH), but rarely ¹O₂. Herein, we innovatively realize the selective generation of ¹O₂ via O₂ activation by a facile molybdenum (Mo)/Cu²⁺ system. In this system, Mo firstly reduces Cu²⁺ in solution to low-valence Cu⁰/Cu⁺ on its surface. Cu⁰/Cu⁺ activates O₂ to generate superoxide radical (O₂^•-). Importantly, O₂^•- can be captured immediately and oxidized to ¹O₂ by surface-bound Mo⁶⁺ rather than reduced to H₂O₂. As a result, the Mo/Cu²⁺ system can selectively produce ¹O₂. Under air and O₂ conditions, the degradation efficiency of ibuprofen by Mo/Cu²⁺ system is 67.2 % and 76.6 %, respectively. The degradation efficiencies of bisphenol A, rhodamine B and furfuryl alcohol are 77.1 %, 87.7 % and 91.1 %, respectively. The dosages of Mo and Cu²⁺ are 0.4 g/L and 3 mM, respectively, and the reaction time is 2 h. Interestingly, the activity of Mo decreased by only 4.2 % after 4 cycles. Therefore, this study provides a green pathway to selectively generate ¹O₂ for advanced oxidation processes.

Flower ball cathode assembled from Cu doped Co3S4/Ni3S2 ultrathin nanosheets in a photocatalytic fuel cell for efficient photoelectrochemical rifampicin purification and simultaneous electricity generation based on a CuO QDs/TiO2/WO3 photoanode

Herein, an efficient CuO QDs/TiO₂/WO₃ photoanode and a Cu doped Co₃S₄/Ni₃S₂ cathode were successfully synthesized. The optimized CuO QDs/TiO₂/WO₃ photoanode achieved a photocurrent density of 1.93 mA cm^-2 at 1.23 vs. RHE, which was 2.27 times that of a WO₃ photoanode. The CuO QDs/TiO₂/WO₃-buried junction silicon (BJS) photoanode was coupled with the Cu doped Co₃S₄/Ni₃S₂ cathode to construct a novel photocatalytic fuel cell (PFC) system. The as-established PFC system showed a high rifampicin (RFP) removal ratio of 93.4% after 90 min and maximum power output of 0.50 mW cm^-2. Quenching tests and EPR spectra demonstrated that ˙OH, ˙O₂^- and ¹O₂ were the main reactive oxygen species in the system. This work provides a possibility to construct a more efficient PFC system for environmental protection and energy recovery in the future.

α-Fe2O3 mediated periodate activation for selective degradation of phenolic compounds via electron transfer pathway under visible irradiation

Periodate (PI)-photoactivated advanced oxidation process (AOP) has recently received increasing attention for the removal of micropollutants from water. However, periodate is mainly driven by high-energy ultraviolet light (UV) in most cases, and few studies have extended it to the visible range. Herein, we proposed a new PI visible light activation system employing α-Fe₂O₃ as catalyst. It is completely different from traditional PI-AOP based on hydroxyl radicals (•OH) and iodine radical (•IO₃). The vis-α-Fe₂O₃/PI system can selectively degrade the phenolic compounds via non-radical pathway under the visible range. Notably, the designed system not only shows a well pH tolerance and environmental stability, but also exhibits a strong substrate-dependent reactivity. Both quenching experiments and electron paramagnetic resonance (EPR) experiments demonstrate that photogenerated holes are the main active species in this system. Moreover, a series of photoelectrochemical experiments reveal that PI can effectively inhibit the carrier recombination on the α-Fe₂O₃ surface, thereby improving the utilization of photogenerated charges and increasing the number of photogenerated holes, which effectively reacts with 4-CP through electron transfer way. In a word, this work proposes a cost-effective, green and mild mean to activate PI, and provides a facile way to solve the fatal shortcomings (i.e., inappropriate band edge position, rapid charge recombination and short hole diffusion length) of traditional iron oxide semiconductor photocatalysts.

Visible light-driven photocatalytic degradation of Microcystin-LR by Bi2WO6/Reduced graphene oxide heterojunctions: Mechanistic insight, DFT calculation and degradation pathways

Developing heterostructure photocatalysts for removing Microcystin-LR (MC-LR) under visible light was of positive significance to control the risk of Microcystins and ensure the safety of water quality. Herein, the Bi₂WO₆/Reduced graphene oxide (RGO) nanocomposites were prepared via a simple one-spot hydrothermal method for the first time to degrade MC-LR. The optimized Bi₂WO₆/RGO (Bi₂WO₆/RGO_3%) achieved a removal efficiency of 82.3% toward MC-LR, with 1.9-fold higher efficiencies than Bi₂WO₆, and it showed superior reusability and high stability after 5 cycles. The degradation efficiency of MC-LR demonstrated a negative trend with the initial concentration of MC-LR, fulvic acid, and initial algal density increased, while MC-LR removal rate for the presence of anions was in the order of Cl^- > CO₃^-2 > NO₃^- > H₂PO₄^-. The degradation efficiency of MC-LR could reach up to 82.3% within 180 min in the neutral condition. The active species detection experiments and EPR measurements demonstrated that the holes (h⁺), hydroxide radicals (∙OH), and superoxide radicals (∙O₂^-) participated in the degradation of MC-LR. The DFT calculations showed that 0.56 of electron transferred from Bi₂WO₆ to RGO, indicating RGO introduction could prevent the recombination of photoelectrons and holes and was beneficial for MC-LR degradation. Finally, the possible intermediate products and degradation pathways were also proposed by the LC-MS/MS analysis.

Spontaneous Formation of Low Valence Copper on Red Phosphorus to Effectively Activate Molecular Oxygen for Advanced Oxidation Process

Efficient spontaneous molecular oxygen (O₂) activation is an important technology in advanced oxidation processes. Its activation under ambient conditions without using solar energy or electricity is a very interesting topic. Low valence copper (LVC) exhibits theoretical ultrahigh activity toward O₂. However, LVC is difficult to prepare and suffers from poor stability. Here, we first report a novel method for the fabrication of LVC material (P-Cu) via the spontaneous reaction of red phosphorus (P) and Cu²⁺. Red P, a material with excellent electron donating ability and can directly reduce Cu²⁺ in solution to LVC via forming Cu-P bonds. With the aid of the Cu-P bond, LVC maintains an electron-rich state and can rapidly activate O₂ to produce ·OH. By using air, the ·OH yield reaches a high value of 423 μmol g^-1 h^-1, which is higher than traditional photocatalytic and Fenton-like systems. Moreover, the property of P-Cu is superior to that of classical nano-zero-valent copper. This work first reports the concept of spontaneous formation of LVC and develops a novel avenue for efficient O₂ activation under ambient conditions.

Natural manganese sand activates sodium hypochlorite to enhance ionic organic contaminants removal: Optimization, modeling, and mechanism

Although sodium hypochlorite acting as an oxidant has been investigated for the role it plays in the degradation of organic contaminants, little attention has been paid to its activation and efficient utilization. In this study, natural manganese sand (NMS) was verified to be effective for activation of sodium hypochlorite (NaClO). Due to the generation of O₂^-, the removal efficiency of ionic organic contaminants in NMS/NaClO system was 1.9-4.1 times higher than that in NMS or NaClO alone. Hence, NMS activated NaClO system performed ~96.6 % contaminants removal efficiency at a wide pH range (pH 5-9). Kinetic modeling yielded that the NMS dosage was more important than NaClO dosage. Long-term stability was observed in the presence of various salts (bicarbonate, sulfate, phosphate, and chloride). Characterization results revealed that electron transfer among NMS, NaClO, and organic contaminants was responsible for NaClO activation. Then NaClO-based Fenton-like process was proposed by tracing the degradation intermediates of methyl orange (MO) and generations of reactive oxygen species in the MO/NMS/NaClO system. This study presents the potential of NMS to activate NaClO and enhance ionic organic contaminants removal from aquatic environments.

Mo-Based Heterogeneous Interface and Sulfur Vacancy Synergistic Effect Enhances the Fenton-like Catalytic Performance for Organic Pollutant Degradation

Heterogeneous Fenton-like reactions (HFLRs) based on the in situ electrochemical generation of hydrogen peroxide (H₂O₂) are one of the green methods to remediate organic pollutants in wastewater. However, the design of Fenton-like catalysts with specific active sites and high pollutant degradation rate is still challenging. Here, MoS₂-MoC and MoS₂-Mo₂N catalytic cathodes with heterojunctions were successfully prepared, and the mechanism by which hydroxyl radicals and singlet oxygen (¹O₂) were generated cleanly without adding chemical additives other than oxygen was clarified. The composite catalysts contained more sulfur vacancies, and the catalytic cathode achieved a high paracetamol pollutant degradation efficiency with 0.17 kWh g^-1 TOC specific energy consumption. And almost 5 times higher activity was achieved compared to a pure MoS₂ catalytic cathode. Experimental studies confirmed that the production of ¹O₂ was based on the transformation of superoxide radicals by Mo⁶⁺, and ¹O₂ accounted for approximately 66% of the total degradation and enhanced the nonradical behavior in the reaction. This work provides a sustainable strategy for pollutant utilization, which is valuable for solving the difficult problems of HFLRs and developing new environmental remediation technologies.

Insight into core -shell microporous zinc silicate adsorbent to eliminate antibiotics in aquatic environment under the COVID-19 pandemic

Under the new crown pneumonia (COVID-19) epidemic, the intensive use of therapeutic drugs has caused certain hidden danger to the safety of the water environment. Therefore, the core-shell microporous zinc silicate (SiO₂@ZSO) was successfully prepared and used for the adsorption of chloroquine phosphate (CQ), tetracycline (TC) and ciprofloxacin (CIP) for eliminating the threat of COVID-19. The adsorption efficiencies of 20 mg L^-1 of CQ, TC and CIP by SiO₂@ZSO were all up to 60% after 5 min. The adsorption capacity of SiO₂@ZSO for CQ, TC and CIP can reach 49.01 mg g^-1, 56.06 mg g^-1 and 104.77 mg g^-1, respectively. The adsorption process is primarily physical adsorption, which is heterogeneous, spontaneous and preferential. Moreover, the effects of temperature, pH, salinity, and reusability on the adsorption of CQ, TC, and CIP on SiO₂@ZSO were investigated. The adsorption mechanism mainly involves electrostatic attraction, partitioning and hydrogen bonding, which is insightful through the changes of the elements and functional groups before and after adsorption. This work provides a solution to the problems faced by the treatment of pharmaceuticals wastewater under the COVID-19 epidemic.

Core-Shell Hierarchical Fe/Cu Bimetallic Fenton Catalyst with Improved Adsorption and Catalytic Performance for Congo Red Degradation

The preparation of heterogeneous Fenton catalysts with both adsorption and catalytic properties has become an effective strategy for the treatment of refractory organic wastewater. In this work, 4A-Fe@Cu bimetallic Fenton catalysts with a three-dimensional core-shell structure were prepared by a simple, template-free, and surfactant-free methodology and used in the adsorption and degradation of Congo red (CR). The results showed that the open three-dimensional network structure and the positive charge of the surface of the 4A-Fe@Cu catalyst could endow a high adsorption capacity for CR, reaching 432.9 mg/g. The good adsorption property of 4A-Fe@Cu for CR not only did not inactivate the catalytic site on 4A-Fe@Cu but also could promote the contact between CR and the active sites on the catalyst surface and accelerate the degradation process. The 4A-Fe@Cu bimetallic catalyst exhibited higher catalytic activity than monometallic 4A@Cu and/or 4A-Fe catalysts due to low work function value. The effects of different pH, H2O2 dosages, and catalyst dosages on the catalytic performance of 4A-Fe@Cu were explored. In the conditions of 7.2 mM H2O2, 2 g/L 4A-Fe@Cu, and 1 g/L CR solution, the degradation ratio of CR by 4A-Fe@Cu could reach 99.2% at pH 8. This strategy provided guidance to the design of high-performance Fenton-like catalysts with both adsorption and catalysis properties for dye wastewater treatment.

Construction lamellar BaFe12O19/Bi3.64Mo0.36O6.55 photocatalyst for enhanced photocatalytic activity via a photo-Fenton-like Mo6+/Mo4+redox cycle

The novel BaFe₁₂O₁₉/Bi_3.64Mo_0.36O_6.55 composite materials were constructed as magnetically recyclable photo-Fenton-like degradation systems. The composite catalyst not only promoted the effective transfer of photo-generated electrons and improved the Mo⁶⁺/Mo⁴⁺ cycle consequent, but also activated hydrogen peroxide to generate oxidizing free radicals. BaFe₁₂O₁₉/Bi_3.64Mo_0.36O_6.55-0.25 exhibited an outstanding degradation performance for tetracycline hydrochloride it is 1.3 times to Bi_3.64Mo_0.36O_6.55. The thermal catalytic performance of the Bi_3.64Mo_0.36O_6.55 monomer is similar to that of the BaFe₁₂O₁₉/Bi_3.64Mo_0.36O_6.55 material without light. However, the removal rate of BaFe₁₂O₁₉/Bi_3.64Mo_0.36O_6.55 material reaches 84.5% after 60 min with light, far exceeding that of Bi_3.64Mo_0.36O_6.55 material. By way of the contrast experiment with light and without light, it is further demonstrated that interfacial interaction between BaFe₁₂O₁₉ and Bi_3.64Mo_0.36O_6.55 acted a key role in the photocatalytic reaction system. It is also a good advantage that pollutants can be efficiently degraded without adjusting the pH. The characterization of photocurrent and X-ray photoelectron spectroscopy (XPS) also further proved the synergy between the two materials, which is useful to the separation of electrons and holes. The synergy ultimately improves the degradation performance. Besides, BaFe₁₂O₁₉/Bi_3.64Mo_0.36O_6.55 can be easily separated by an external magnetic field after the photocatalytic activity reaction owing to BaFe₁₂O₁₉'s magnetic properties. It provides a new research idea for the construction and iron-based heterogeneous Fenton-like system for magnetic degradation of antibiotics.

Reactive species conversion into 1O2 promotes substantial inhibition of chlorinated byproduct formation during electrooxidation of phenols in Cl--laden wastewater

The generation of chlorinated byproducts during the electrochemical oxidation (EO) of Cl^--laden wastewater is a significant concern. We aim to propose a concept of converting reactive species (e.g., reactive chlorines and HO^• resulting from electrolysis) into ¹O₂ via the addition of H₂O₂, which substantially alleviates chlorinated organic formation. When phenol was used as a model organic compound, the results showed that the H₂O₂-involving EO system outperformed the H₂O₂-absent system in terms of higher rate constants (5.95 × 10^-2 min^-1vs. 2.97 × 10^-2 min^-1) and a much lower accumulation of total organic chlorinated products (1.42 mg L^-1vs. 8.18 mg L^-1) during a 60 min operation. The rate constants of disappearance of a variety of phenolic compounds were positively correlated with the Hammett constants (σ), suggesting that the reactive species preferred oxidizing phenols with electron-rich groups. After the identification of ¹O₂ that was abundant in the bulk solution with the use of electron paramagnetic resonance and computational kinetic simulation, the routes of ¹O₂ generation were revealed. Despite the consensus as to the contribution of reaction between H₂O₂ and ClO^- to ¹O₂ formation, we conclude that the predominant pathway is through H₂O₂ reaction with electrogenerated HO^• or chlorine radicals (Cl^• and Cl₂^•-) to produce O₂^•-, followed by self-combination. Density functional theory calculations theoretically showed the difficulty in forming chlorinated byproducts for the ¹O₂-initiated phenol oxidation in the presence of Cl^-, which, by contrast, easily occurred for the Cl^•-or HO^•-initiated phenol reaction. The experiments run with real coking wastewater containing high-concentration phenols further demonstrated the superiority of the H₂O₂-involving EO system. The findings imply that this unique method for treating Cl^--laden organic wastewater is expected to be widely adopted for generalizing EO technology for environmental applications.

Microbe Regulates the Mineral Photochemical Activity and Organic Matter Compositions in Water

Photochemical reactions that widely occur in aquatic environments play important roles in carbon fate (e.g., carbon conversion and storage from organic matter) in ecosystems. Aquatic microbes and natural minerals further regulate carbon fate, but the processes and mechanisms remain largely unknown. Herein, the interaction between Escherichia coli and pyrite and its influence on the fate of carbon in water were investigated at the microscopic scale and molecular level. The results showed that saccharides and phenolic compounds in microbial extracellular polymeric substances helped remove pyrite surface oxides via electron transfer. After the removal of surface oxides on pyrite, the photochemical properties under visible-light irradiation were significantly decreased, such as reactive oxygen species and electron transfer capacity. Unlike the well-accepted theory of minerals protecting organic matter in the soil, the organic matter adsorbed on minerals preferred degradation due to the enhanced photochemical reactions in water. In contrast, the minerals transformed by microbes suppressed the decomposition of organic matter due to the passivation of the chemical structure and activity. These results highlight the significance of mineral chemical activity on organic matter regulated by microbes and provide insights into organic matter conversion in water.

Amidoxime functionalized PVDF-based chelating membranes enable synchronous elimination of heavy metals and organic contaminants from wastewater

Aiming at the synchronous elimination of heavy metals and organic contaminants from wastewater, the amidoxime functionalized PVDF-based chelating membrane was fabricated in this study. The structure and morphology of the chelating membrane were characterized using infrared spectroscopy (FT-IR), nuclear magnetic resonance spectrometer (NMR) and scanning electron microscopy (SEM). The SEM results show that the chemical modification with amidoxime groups did not damage the structure of the PVDF-based membrane. The chelating membrane has a high removal efficiency for Cu²⁺ (77.33%) and Pb²⁺ (79.23%) owing to the chemisorption through coordination bonds. However, the chelating membrane exhibits a low removal efficiency for Cd²⁺ (29.88%) due to the physical adsorption. The chelating membrane has a high rejection efficiency of BSA (95.17%) and lysozyme (70.09%), which is attributed to the sieving effect and increased hydrophobicity. Furthermore, the membrane performance for simultaneously removing metals and proteins from simulated wastewater was examined. The interaction of metal ions with proteins (BSA and lysozyme) can enhance the ion removal efficiency of the chelated membrane, but decrease the protein rejection efficiency due to the destructive effect. The amidoxime functionalized PVDF-based chelating membrane has a high potential for application in wastewater treatment.

Trace Iron as single-electron shuttle for interdependent activation of peroxydisulfate and HSO3-/O2 enables accelerated generation of radicals

The generation of reactive oxygen species generally requires initiators in various environmental remediation processes, which necessitates high dosage of activators and downstream treatment for eliminating the accumulation of deactivated catalysts. Herein, a coupled process was constructed using trace iron for simultaneously activating HSO₃^-/O₂ system and peroxydisulfate (PDS) oxidation system, where the iron ions (2 mg/L) transferred single-electron from the former system to the latter due to the moderate redox potential (Fe³⁺/Fe²⁺, +0.77 V) between the potentials of SO₃^·-/HSO₃^- (+0.63 V) and PDS/SO₄^·- (+2.01 V). Hence, the phenol degradation quickly occurred at a first-order kinetic constant of k₁=0.223 min^-1 due to the accelerated generation of sulfate radical (SO₄^·-) and hydroxyl radical (^·OH) in the process. The k₁ value was almost 6-fold of that in the deoxygenated condition (0.040 min^-1). Density function theory reveals that the single electron shuttle spatially separates the electron-donating activation of HSO₃^- and electron-accepting activation of PDS, while avoiding the "mutual-annihilation" of HSO₃^- and S₂O₈^2- via direct two-electron transfer. Finally, utilizing the in-situ generated electron-shuttle (dissolved iron from cast iron pipe), the HSO₃^-/PDS reagent could efficiently inactivate the chlorine-resistant pathogens and inhibits biofilm regrowth inside the distribution systems at regular intervals or infectious disease outbreak in a neighborhood.

Self-cycled photo-Fenton-like system based on an artificial leaf with a solar-to-H2O2 conversion efficiency of 1.46

Millions of families around the world remain vulnerable to water scarcity and have no access to drinking water. Advanced oxidation processes (AOPs) are an effective way towards water purification with qualified reactive oxygen species (ROSs) while are impeded by the high-cost and tedious process in either input of consumable reagent, production of ROSs, and the pre-treatment of supporting electrolyte. Herein, we couple solar light-assisted H₂O₂ production from water and photo-Fenton-like reactions into a self-cyclable system by using an artificial leaf, achieving an unassisted H₂O₂ production rate of 0.77 μmol/(min·cm²) under 1 Sun AM 1.5 illumination. Furthermore, a large (70 cm²) artificial leaf was used for an unassisted solar-driven bicarbonate-activated hydrogen peroxide (BAP) system with recycled catalysts for real-time wastewater purification with requirements for only water, oxygen and sunlight. This demonstration highlights the feasibility and scalability of photoelectrochemical technology for decentralized environmental governance applications from laboratory benchtops to industry.

Continuous generation of reactive oxygen species is desirable in the advanced oxidation process. Here, the authors report a self-cycled photoFenton-like with a scalable artificial leaf for production of H₂O₂ from water with solar-to-H₂O₂ efficiency of 1.46%.

Self-Accelerating Interfacial Catalytic Elimination of Gaseous Sulfur-Containing Volatile Organic Compounds as Microbubbles in a Facet-Engineered Three-Dimensional BiOCl Sponge Fenton-Like Process

The elimination of gaseous sulfur-containing volatile organic compounds (S-VOCs) by a microbubble-assisted Fenton-like process is an innovative strategy. Herein, we established a microbubble-assisted Fenton-like process to eliminate malodorous microbubble CH₃SH as representative gaseous S-VOCs, in which BiOCl nanosheets loaded on a three-dimensional sponge were exposed to (001) or (010) facets and induced Fenton-like interface reactions. Intriguingly, the microbubble-assisted Fenton-like process significantly removed 99.9% of CH₃SH, higher than that of the macrobubble-assisted Fenton-like process (39.0%). The self-accelerating interfacial catalytic mechanism was in-depth identified by in situ ATR-FTIR, PTR-TOF-MS, EPR, and DFT computational study. The extraordinary elimination performance of microbubble-assisted Fenton-like process lies in the enhancing dissolution/mass transfer of gaseous CH₃SH in the gas/liquid phase and the tight contact between CH₃SH-microbubbles and 3D-BiOCl sponge due to the low rising velocity (0.13 mm s^-1) and negative charge (-45.53 mV) of CH₃SH-microbubbles, as well as the effective generation of ¹O₂ by activating the enriched dissolved oxygen in CH₃SH-microbubble via effective electron-polarized sites on 3D-BiOCl sponge. Furthermore, CH₃SH-microbubbles transferred electrons to H₂O₂ through electron-rich oxygen vacancy centers of the 3D-BiOCl sponge to generate more •OH, thus achieving excellent elimination performance. Overall, this study demonstrates the enhanced self-accelerating interfacial catalytic elimination by S-VOC microbubble and provides the underlying mechanisms.

Selenization governs the intrinsic activity of copper-cobalt complexes for enhanced non-radical Fenton-like oxidation toward organic contaminants

Non-radical oxidation pathways in the Fenton-like process have a superior catalytic activity for the selective degradation of organic contaminants under complicated water matrices. Whereas the synthesis of high-performance catalysts and research on reaction mechanisms are unsatisfactory. Herein, it was the first report on copper-cobalt selenide (CuCoSe) that was well-prepared to activate hydrogen peroxide (H₂O₂) for non-radical species generation. The optimized CuCoSe+H₂O₂ system achieved excellent removal of chlortetracycline (CTC) in 10 min at neutral pH along with pleasing reusability and stability. Moreover, it exhibited great anti-interference capacity to inorganic anions and natural organic matters even in actual applications. Multi-surveys verified that singlet oxygen (¹O₂) was the dominant active species in this reaction and electron transfer on the surface-bound of CuCoSe and H₂O₂ likewise played an important role in direct CTC oxidation. Where the synergetic metals of Cu and Co accounted for the active sites, and the introduced Se atoms accelerated the circulation efficiency of Co³⁺/Co²⁺, Cu²⁺/Cu⁺ and Cu²⁺/Co²⁺. Simultaneously, the produced Se/O vacancies further facilitated electron mediation to enhance non-radical behaviors. With the aid of intermediate identification and theoretical calculation, the degradation pathways of CTC were proposed. And the predicted ecotoxicity indicated a decrease in underlying environmental risk.

Insights into a novel CuS/percarbonate/tetraacetylethylenediamine process for sulfamethazine degradation in alkaline medium

This work presents a novel CuS/percarbonate/tetraacetylethylenediamine (CuS/SPC/TAED) process for the degradation of sulfamethazine (SMT). Results indicated that the CuS/SPC/TAED process enabled the efficient generation of peracetic acid (PAA), which can be efficiently activated by CuS in alkaline reaction media, and 93.6% of SMT was degraded in 30 min. Mechanism study revealed that the available reactive oxygen species (ROS) including hydroxyl radical (^•OH), carbonate radical (CO₃^•-), superoxide radical (O₂^•-), singlet oxygen (¹O₂), and organic radicals (R-O^•). Among them, R-O^• (acetyloxyl radical (CH₃CO₂^•) and acetylperoxyl radical (CH₃CO₃^•)) were confirmed to be the primary species that contributed to SMT degradation. Simultaneously, the role of sulfur species and carbonate ions were explored. It was found that the reductive O₂^•- and sulfur species rendered the efficient redox of Cu species. Besides, the effects of key influencing factors including SPC/TAED mole ratio, CuS dosage, initial pH, temperature, and nontarget matrix constituents on SMT degradation were examined. Finally, the degradation intermediates of SMT was identified, and the toxicity of these products was estimated by quantitative structure-activity relationship (QSAR) analysis. Overall, this work offers a new and simple strategy for antibiotic-polluted water remediation.

An Electrochemical Strategy for Simultaneous Heavy Metal Complexes Wastewater Treatment and Resource Recovery

Heavy metals chelated with coexisting organic ligands in wastewater impose severe risks to public health and the ambient ecosystem but are also valuable metal resources. For sustainable development goals, the treatment of heavy metal complexes wastewater requires simultaneous metal-organic bond destruction and metal resource recovery. In this study, we demonstrated that a neutral pH electro-Fenton (EF) system, which was composed of an iron anode, carbon cloth cathode, and sodium tetrapolyphosphate electrolyte (Na₆TPP), could induce a successive single-electron activation pathway of molecular oxygen due to the formation of Fe(II)-TPP complexes. The boosted •OH generation in the Na₆TPP-EF process could decomplex 99.9% of copper ethylene diamine tetraacetate within 8 h; meanwhile, the released Cu ions were in situ deposited on the carbon cloth cathode in the form of Cu nanoparticles with a high energy efficiency of 2.45 g kWh^-1. Impressively, the recovered Cu nanoparticles were of purity over 95.0%. More importantly, this neutral EF strategy could realize the simultaneous removal of Cu, Ni, and Cr complexes from real electroplating effluents. This study provides a promising neutral EF system for simultaneous heavy metal complexes wastewater treatment and resource recovery and sheds light on the importance of molecular oxygen activation in the field of pollutant control.

Synthesis of Stabilized Iron Nanoparticles from Acid Mine Drainage and Rooibos Tea for Application as a Fenton-like Catalyst

Intensive mining activities generate toxic acid mine drainage (AMD) effluents containing a high concentration of metals, including iron. The chemical synthesis of iron nanoparticles from this waste could lead to further environmental concerns. Therefore, the green synthesis of nanoparticles using plants has gained significant interest because of several benefits, including being eco-friendly. The current study reports a novel approach involving the synthesis of stabilized iron nanoparticles from AMD using rooibos tea extract. An aqueous solution of rooibos tea was prepared and titrated with AMD to reduce Fe²⁺/Fe³⁺. The samples synthesized under optimum conditions were characterized by TEM, XRD, FTIR, UV-Vis, and EDS. The results revealed that the nanoparticles had an average particle size of 36 nm with a spherical shape. These particles showed promising application as a Fenton-like catalyst for the degradation of textile dye (orange II sodium salt) with a removal efficiency of 94% within 30 min. Thus, the stabilized iron nanoparticles synthesized here performed in higher ranges than the currently reported Fenton-like catalysts regarding dye removal efficiency and reaction time.

Sulfur Defect-Engineered Biodegradable Cobalt Sulfide Quantum Dot-Driven Photothermal and Chemodynamic Anticancer Therapy

Chemodynamic therapy (CDT), as a powerful tumor therapeutic approach with low side effects and selective therapeutic efficiency, has gained much attention. However, the low intracellular content of H₂O₂ and the cellular bottleneck of low intracellular oxidative reaction rates at tumor sites have limited the antitumor efficacy of CDT. Herein, a series of sulfur-deficient engineered biodegradable cobalt sulfide quantum dots (CoS_x QDs) were constructed for improved synergistic photothermal- and hyperthermal-enhanced CDT of tumors through regulating the photothermal conversion efficiency (PCE) and Fenton-like activity. Through defect engineering, we modulated the PCE and promoted the Fenton catalytic capability of CoS_x QDs. With increasing defect sites, the Fenton-like activity improved to generate more toxic ^•OH, while the photothermal effect declined slightly. In light of above unique superiorities, the best synergistic effects of CoS_x QDs were obtained through comparing their PCE and catalytic activity by regulating the sulfur defect fraction degree in these QDs during the synthetic process. In addition, the ultrasmall size and biodegradation endowed QDs with the ability to be rapidly decomposed to ions that were easily excreted after therapy, thus reducing biogenic accumulation in the body with lowered systemic side effects. The in vitro/vivo results demonstrated that the photothermal- and hyperthermal-enhanced chemodynamic effect of CoS_x QDs can enable remarkable anticancer properties with favorable biocompatibility. In this study, the defect-driven mechanism for the photothermal-enhanced Fenton-like reaction provides a flexible strategy to deal with different treatment environments, holding great promise in developing a multifunctional platform for cancer treatment in the future.