1
|
Wang C, Wu J, Liu L, Xu D, Liu Y, Li S, Hou W, Wang J, Chen X, Sheng L, Lin H, Yu D. Improving osteoinduction and osteogenesis of Ti6Al4V alloy porous scaffold by regulating the pore structure. Front Chem 2023; 11:1190630. [PMID: 37265590 PMCID: PMC10229796 DOI: 10.3389/fchem.2023.1190630] [Citation(s) in RCA: 1] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/21/2023] [Accepted: 05/04/2023] [Indexed: 06/03/2023] Open
Abstract
Titanium alloy scaffolds with a porous structure have attracted much attention in bone defect repair. However, which pore structure is more beneficial to bone defect repair is controversial. In the present research, the Ti6Al4V alloy porous scaffolds with gradient pore sizes were designed and fabricated. The microstructure characterization, tests of mechanical properties, and in vitro and in vivo experiments have been performed to systematically evaluate the effect of pore size on osteoinduction and osteogenesis. The results revealed that the contact angle with water, compressive strength, and elastic modulus of the Ti6Al4V alloy porous scaffolds decreased gradually with the increase of pore size. However, there were obvious drops when the pore size of the porous scaffold was around 600 μm. As the pore size increased, the proliferation and integrin β1 of RAW 264.7 macrophages seeded on Ti6Al4V alloy porous scaffolds increased at first, reaching a maximum value at a pore size of around 600 μm, and then decreased subsequently. The proliferation, integrin β1, and osteogenic gene-related expressions of Bone marrow mesenchymal stem cells (BMSCs) seeded on Ti6Al4V alloy porous scaffolds with different pore sizes all exhibited similar variations which rose with increased pore size firstly, obtaining the maximum value at pore size about 600 μm, and then declined. The in vivo experiments confirmed the in vitro results, and the Ti6Al4V alloy porous scaffold with a pore size of 600 μm possessed the better capability to induce new bone formation. Therefore, for the design of Ti6Al4V alloy with a regular porous scaffold, the surface morphology, porosity, strength, and elastic modulus should be considered systematically, which would determine the capability of osteoinduction and osteogenesis.
Collapse
Affiliation(s)
- Chao Wang
- Hospital of Stomatology, Guanghua School of Stomatology, Sun Yat-sen University, Guangzhou, China
- Guangdong Provincial Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou, China
| | - Jie Wu
- Hospital of Stomatology, Guanghua School of Stomatology, Sun Yat-sen University, Guangzhou, China
- Guangdong Provincial Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou, China
| | - Leyi Liu
- Hospital of Stomatology, Guanghua School of Stomatology, Sun Yat-sen University, Guangzhou, China
- Guangdong Provincial Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou, China
| | - Duoling Xu
- Hospital of Stomatology, Guanghua School of Stomatology, Sun Yat-sen University, Guangzhou, China
- Guangdong Provincial Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou, China
| | - Yuanbo Liu
- Hospital of Stomatology, Guanghua School of Stomatology, Sun Yat-sen University, Guangzhou, China
- Guangdong Provincial Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou, China
| | - Shujun Li
- Institute of Metal Research, Chinese Academy of Sciences, Shenyang, China
| | - Wentao Hou
- Institute of Metal Research, Chinese Academy of Sciences, Shenyang, China
| | - Jian Wang
- Shenzhen Institute, Peking University, Shenzhen, China
| | - Xun Chen
- Hospital of Stomatology, Guanghua School of Stomatology, Sun Yat-sen University, Guangzhou, China
- Guangdong Provincial Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou, China
| | - Liyuan Sheng
- Shenzhen Institute, Peking University, Shenzhen, China
| | - Huancai Lin
- Hospital of Stomatology, Guanghua School of Stomatology, Sun Yat-sen University, Guangzhou, China
- Guangdong Provincial Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou, China
| | - Dongsheng Yu
- Hospital of Stomatology, Guanghua School of Stomatology, Sun Yat-sen University, Guangzhou, China
- Guangdong Provincial Key Laboratory of Stomatology, Sun Yat-sen University, Guangzhou, China
| |
Collapse
|
2
|
Li M, Wang M, Wei L, Werner A, Liu Y. Biomimetic calcium phosphate coating on medical grade stainless steel improves surface properties and serves as a drug carrier for orthodontic applications. Dent Mater 2023; 39:152-161. [PMID: 36610898 DOI: 10.1016/j.dental.2022.12.009] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/05/2022] [Revised: 12/05/2022] [Accepted: 12/24/2022] [Indexed: 01/07/2023]
Abstract
OBJECTIVE Recently, stainless steel (SSL) miniscrew implants have been used in orthodontic clinics as temporary anchorage devices. Although they have excellent physical properties, their biocompatibility is relatively poor. Previously, our group developed a two-phase biomimetic calcium phosphate (BioCaP) coating that can significantly improve the biocompatibility of medical devices. This study aimed to improve the biocompatibility of SSL by coating SSL surface with the BioCaP coating. METHODS Titanium (Ti) discs and SSL discs (diameter: 5 mm, thickness: 1 mm) were used in this study. To form an amorphous layer, the Ti discs were immersed in a biomimetic modified Tyrode solution (BMT) for 24 h. The SSL discs were immersed in the same solution for 0 h, 12 h, 24 h, 36 h and 48 h. To form a crystalline layer, the discs were then immersed in a supersaturated calcium phosphate solution (CPS) for 48 h. The surface properties of the BioCaP coatings were analysed. In addition, bovine serum albumin (BSA) was incorporated into the crystalline layer during biomimetic mineralisation as a model protein. RESULTS The morphology, chemical composition and drug loading capacity of the BioCaP coating on smooth SSL were confirmed. This coating improved roughness and wettability of SSL surface. In vitro, with the extension of BMT coating period, the cell seeding efficiency, cell spreading area and cell proliferation on the BioCaP coating were increased. SIGNIFICANCE These in vitro results show that the BioCaP coating can improve surface properties of smooth medical grade SSL and serve as a carrier system for bioactive agents.
Collapse
Affiliation(s)
- Menghong Li
- Department of Oral Cell Biology, Academic Center for Dentistry Amsterdam (ACTA), University of Amsterdam and Vrije University Amsterdam, Amsterdam, the Netherlands
| | - Mingjie Wang
- Department of Oral Cell Biology, Academic Center for Dentistry Amsterdam (ACTA), University of Amsterdam and Vrije University Amsterdam, Amsterdam, the Netherlands
| | - Lingfei Wei
- Department of Oral Cell Biology, Academic Center for Dentistry Amsterdam (ACTA), University of Amsterdam and Vrije University Amsterdam, Amsterdam, the Netherlands; Department of Oral Implantology, Yantai Stomatological Hospital, Yantai, China; Department of Second Dental Center, Shanghai Ninth People's Hospital, Shanghai Jiao Tong University School of Medicine; College of Stomatology, Shanghai Jiao Tong University; National Center for Stomatology; National Clinical Research Center for Oral Diseases; Shanghai Key Laboratory of Stomatology; Shanghai Research Institute of Stomatology, China
| | - Arie Werner
- Department of Dental Materials Science, Academic Centre for Dentistry Amsterdam (ACTA), University of Amsterdam and Vrije University Amsterdam, Amsterdam, the Netherlands
| | - Yuelian Liu
- Department of Oral Cell Biology, Academic Center for Dentistry Amsterdam (ACTA), University of Amsterdam and Vrije University Amsterdam, Amsterdam, the Netherlands.
| |
Collapse
|
3
|
KATİCA M, TEPEKOY F. The effect of Calcitriol 1,25 (OH)2 - D3 on osteoblast-like cell proliferation during in vitro cultivation. MEHMET AKIF ERSOY ÜNIVERSITESI VETERINER FAKÜLTESI DERGISI 2020. [DOI: 10.24880/maeuvfd.653000] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/09/2022] Open
|
4
|
Osteoblasts grown on microroughened titanium surfaces regulate angiogenic growth factor production through specific integrin receptors. Acta Biomater 2019; 97:578-586. [PMID: 31349056 DOI: 10.1016/j.actbio.2019.07.036] [Citation(s) in RCA: 20] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/29/2019] [Revised: 06/27/2019] [Accepted: 07/22/2019] [Indexed: 01/08/2023]
Abstract
Cellular attachment and response to biomaterials are mediated by integrin receptor binding to extracellular matrix proteins adsorbed onto the material surface. Osteoblasts interact with their substrates via several integrin complexes including fibronectin-binding α5β1 and collagen-binding α1β1 and α2β1. Knockdown of α2 or β1 integrin subunits inhibits the production of factors that promote an osteogenic microenvironment, including osteocalcin, osteoprotegerin, and TGFβ1. Osteoblasts also secrete several angiogenic growth factors such as VEGF-A (VEGF165), FGF-2, and angiopoietin 1, which are regulated by titanium surface topography and surface energy. Here, we examined whether signaling through integrin receptor complexes regulates production and secretion of angiogenic factors during osteoblast differentiation on microtextured Ti surfaces. To do this, integrin subunits α1, α2, α5, and β1 were stably silenced in MG63 osteoblast-like cells cultured on grit-blasted/acid-etched hydrophobic Ti (SLA) or on hydrophilic SLA (modSLA). VEGF-A production increased in response to Ti surface topography and energy in integrin α2, α5, and β1 silenced cells but decreased in α1-silenced cells. FGF-2 decreased on modSLA substrates in both α1 and α2-silenced cells but was unchanged in response to silencing of either α5 or β1. In integrin α1, α2, and β1-silenced cells, Ang-1 increased on modSLA but α5-silencing did not affect Ang-1 production during surface mediated differentiation. These results suggest that signaling through specific integrin receptor complexes during osteoblast differentiation on microstructured Ti substrates, regulates the production of angiogenic factors by those cells, and this is differentially regulated by surface hydrophilicity. STATEMENT OF SIGNIFICANCE: Successful implantation of synthetic biomaterials into bone depends on the biological process known as osseointegration. Osseointegration is a highly regulated communication of cells that orchestrates the migration of progenitor cells towards the implant site and promotes the deposition and mineralization of extracellular matrix proteins within the implant microenvironment, to tightly join the implant to native bone. In this process, angiogenesis functions as the initiation site of progenitor cell migration and is necessary for matrix deposition by providing the necessary nutrients for bone formation. In the present study, we show a novel regulation of specific angiogenic growth factors by integrin receptor complexes. This research is important to develop biomaterials that promote and maintain osseointegration through proper vascularization and prevent implant failure in patients lacking sufficient angiogenesis.
Collapse
|
5
|
Lopes HB, Freitas GP, Elias CN, Tye C, Stein JL, Stein GS, Lian JB, Rosa AL, Beloti MM. Participation of integrin β3 in osteoblast differentiation induced by titanium with nano or microtopography. J Biomed Mater Res A 2019; 107:1303-1313. [PMID: 30707485 DOI: 10.1002/jbm.a.36643] [Citation(s) in RCA: 19] [Impact Index Per Article: 3.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/22/2018] [Revised: 01/03/2019] [Accepted: 01/29/2019] [Indexed: 12/14/2022]
Abstract
The major role of integrins is to mediate cell adhesion but some of them are involved in the osteoblasts-titanium (Ti) interactions. In this study, we investigated the participation of integrins in osteoblast differentiation induced by Ti with nanotopography (Ti-Nano) and with microtopography (Ti-Micro). By using a PCR array, we observed that, compared with Ti-Micro, Ti-Nano upregulated the expression of five integrins in mesenchymal stem cells, including integrin β3, which increases osteoblast differentiation. Silencing integrin β3, using CRISPR-Cas9, in MC3T3-E1 cells significantly reduced the osteoblast differentiation induced by Ti-Nano in contrast to the effect on T-Micro. Concomitantly, integrin β3 silencing downregulated the expression of integrin αv, the parent chain that combines with other integrins and several components of the Wnt/β-catenin and BMP/Smad signaling pathways, all involved in osteoblast differentiation, only in cells cultured on Ti-Nano. Taken together, our results showed the key role of integrin β3 in the osteogenic potential of Ti-Nano but not of Ti-Micro. Additionally, we propose a novel mechanism to explain the higher osteoblast differentiation induced by Ti-Nano that involves an intricate regulatory network triggered by integrin β3 upregulation, which activates the Wnt and BMP signal transductions. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 107A: 1303-1313, 2019.
Collapse
Affiliation(s)
- Helena B Lopes
- Cell Culture Laboratory, School of Dentistry of Ribeirão Preto, University of São Paulo, Ribeirão Preto, SP, Brazil
| | - Gileade P Freitas
- Cell Culture Laboratory, School of Dentistry of Ribeirão Preto, University of São Paulo, Ribeirão Preto, SP, Brazil
| | - Carlos N Elias
- Biomaterials Laboratory, Instituto Militar de Engenharia, Rio de Janeiro, RJ, Brazil
| | - Coralee Tye
- Department of Biochemistry, University of Vermont Cancer Center, University of Vermont, Burlington, Vermont
| | - Janet L Stein
- Department of Biochemistry, University of Vermont Cancer Center, University of Vermont, Burlington, Vermont
| | - Gary S Stein
- Department of Biochemistry, University of Vermont Cancer Center, University of Vermont, Burlington, Vermont
| | - Jane B Lian
- Department of Biochemistry, University of Vermont Cancer Center, University of Vermont, Burlington, Vermont
| | - Adalberto L Rosa
- Cell Culture Laboratory, School of Dentistry of Ribeirão Preto, University of São Paulo, Ribeirão Preto, SP, Brazil
| | - Marcio M Beloti
- Cell Culture Laboratory, School of Dentistry of Ribeirão Preto, University of São Paulo, Ribeirão Preto, SP, Brazil
| |
Collapse
|
6
|
Berger MB, Cohen DJ, Olivares-Navarrete R, Williams JK, Cochran DL, Boyan BD, Schwartz Z. Human osteoblasts exhibit sexual dimorphism in their response to estrogen on microstructured titanium surfaces. Biol Sex Differ 2018; 9:30. [PMID: 29970177 PMCID: PMC6029108 DOI: 10.1186/s13293-018-0190-x] [Citation(s) in RCA: 13] [Impact Index Per Article: 2.2] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 03/06/2018] [Accepted: 06/25/2018] [Indexed: 12/26/2022] Open
Abstract
BACKGROUND Osseointegration is dependent on the implant surface, surrounding bone quality, and the systemic host environment, which can differ in male and female patients. Titanium (Ti) implants with microstructured surfaces exhibit greater pullout strength when compared to smooth-surfaced implants and exhibit enhanced osteogenic cellular responses in vitro. Previous studies showed that 1α,25-dihydroxyvitamin D3 [1α,25(OH)2D3] has a greater effect on rat osteoblast differentiation on microstructured Ti compared to smooth Ti surfaces and tissue culture polystyrene (TCPS). The stimulatory effect of 17β-estradiol (E2) on differentiation is observed in female osteoblasts on micro-rough Ti, but it is not known if male osteoblasts behave similarly in response to E2 and microtopography. This study assessed whether human male and female osteoblasts exhibit sex-specific differences in response to E2 and 1α,25(OH)2D3 when cultured on microstructured Ti surfaces. METHODS Osteoblasts from three male and three female human donors were cultured on Ti discs with varying surface profiles: a smooth pretreatment (PT), a coarse grit-blasted/acid-etched (SLA), and an SLA surface having undergone modification in a nitrogen environment and stored in saline to maintain hydrophilicity (modSLA). Cells cultured on these surfaces were treated with E2 or 1α,25(OH)2D3. RESULTS Male and female human osteoblasts responded similarly to microstructure although there were donor-specific differences; cell number decreased, and osteocalcin (OCN), osteoprotegerin (OPG), and latent and active transforming growth factor 1 increased on SLA and modSLA compared to TCPS. Female osteoblasts had higher alkaline phosphatase activity and OCN production than male counterparts but produced less OPG. Both sexes responded similarly to 1α,25(OH)2D3. E2 treatment reduced cell number and increased osteoblast differentiation and factor production only in female cells. CONCLUSIONS Male and female human osteoblasts respond similarly to microstructure and 1α,25(OH)2D3 but exhibit sexual dimorphism in substrate-dependent responses to E2. E2 affected female osteoblasts, suggesting that signaling is sex-specific and surface-dependent. Donor osteoblasts varied in response, demonstrating the need to test multiple donors when examining human samples. Understanding how male and female cells respond to orthopedic biomaterials will enable greater predictability post-implantation as well as therapies that are more patient-specific.
Collapse
Affiliation(s)
- Michael B Berger
- Department of Biomedical Engineering, College of Engineering, Virginia Commonwealth University, 601 West Main Street, Richmond, VA, 23284-3068, USA
| | - David J Cohen
- Department of Biomedical Engineering, College of Engineering, Virginia Commonwealth University, 601 West Main Street, Richmond, VA, 23284-3068, USA
| | - Rene Olivares-Navarrete
- Department of Biomedical Engineering, College of Engineering, Virginia Commonwealth University, 601 West Main Street, Richmond, VA, 23284-3068, USA
| | | | - David L Cochran
- Department of Periodontics, University of Texas Health Science Center at San Antonio, San Antonio, TX, 78229, USA
| | - Barbara D Boyan
- Department of Biomedical Engineering, College of Engineering, Virginia Commonwealth University, 601 West Main Street, Richmond, VA, 23284-3068, USA. .,Wallace H. Coulter Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, GA, 30332, USA.
| | - Zvi Schwartz
- Department of Biomedical Engineering, College of Engineering, Virginia Commonwealth University, 601 West Main Street, Richmond, VA, 23284-3068, USA.,Department of Periodontics, University of Texas Health Science Center at San Antonio, San Antonio, TX, 78229, USA
| |
Collapse
|
7
|
Vitamin D Promotes MSC Osteogenic Differentiation Stimulating Cell Adhesion and αV β3 Expression. Stem Cells Int 2018; 2018:6958713. [PMID: 29681950 PMCID: PMC5851411 DOI: 10.1155/2018/6958713] [Citation(s) in RCA: 20] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/05/2017] [Accepted: 01/15/2018] [Indexed: 01/17/2023] Open
Abstract
Vitamin D (Vit D) by means of its biological active form, 1α,25-dihydroxyvitamin D3 (1,25(OH)2D3), has a protective effect on the skeleton by acting on calcium homeostasis and bone formation. Furthermore, Vit D has a direct effect on mesenchymal stem cells (MSCs) in stimulating their osteogenic differentiation. In this work, we present for the first time the effect of 1,25(OH)2D3 on MSC adhesion. Considering that cell adhesion to the substrate is fundamental for cell commitment and differentiation, we focused on the expression of αVβ3 integrin, which has a key role in the commitment of MSCs to the osteoblastic lineage. Our data indicate that Vit D increases αVβ3 integrin expression inducing the formation of focal adhesions (FAs). Moreover, we assayed MSC commitment in the presence of the extracellular matrix (ECM) glycoprotein fibronectin (FN), which is able to favor cell adhesion on surfaces and also to induce osteopontin (OPN) expression: this suggests that Vit D and FN synergize in supporting cell adhesion. Taken together, our findings provide evidence that Vit D can promote osteogenic differentiation of MSCs through the modulation of αVβ3 integrin expression and its subcellular organization, thus favoring binding with the matrix protein (FN).
Collapse
|
8
|
Implant Surface Modifications and Osseointegration. SPRINGER SERIES IN BIOMATERIALS SCIENCE AND ENGINEERING 2017. [DOI: 10.1007/978-3-662-53574-5_4] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 01/28/2023]
|
9
|
Lai M, Hermann CD, Cheng A, Olivares-Navarrete R, Gittens RA, Bird MM, Walker M, Cai Y, Cai K, Sandhage KH, Schwartz Z, Boyan BD. Role of α2β1 integrins in mediating cell shape on microtextured titanium surfaces. J Biomed Mater Res A 2014; 103:564-73. [PMID: 24733736 DOI: 10.1002/jbm.a.35185] [Citation(s) in RCA: 32] [Impact Index Per Article: 3.2] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/24/2014] [Accepted: 04/02/2014] [Indexed: 12/21/2022]
Abstract
Surface microroughness plays an important role in determining osteoblast behavior on titanium. Previous studies have shown that osteoblast differentiation on microtextured titanium substrates is dependent on alpha-2 beta-1 (α2β1) integrin signaling. This study used focused ion beam milling and scanning electron microscopy, combined with three-dimensional image reconstruction, to investigate early interactions of individual cells with their substrate and the role of integrin α2β1 in determining cell shape. MG63 osteoblast-like cells on sand blasted/acid etched (SLA) Ti surfaces after 3 days of culturing indicated decreased cell number, increased cell differentiation, and increased expression of mRNA levels for α1, α2, αV, and β1 integrin subunits compared to cells on smooth Ti (PT) surfaces. α2 or β1 silenced cells exhibited increased cell number and decreased differentiation on SLA compared to wild-type cells. Wild-type cells on SLA possessed an elongated morphology with reduced cell area, increased cell thickness, and more apparent contact points. Cells on PT exhibited greater spreading and were relatively flat. Silenced cells possessed a morphology and phenotype similar to wild-type cells grown on PT. These observations indicate that surface microroughness affects cell response via α2β1 integrin signaling, resulting in a cell shape that promotes osteoblastic differentiation.
Collapse
Affiliation(s)
- Min Lai
- Institute for Bioengineering and Bioscience, Georgia Institute of Technology, Atlanta, Georgia; College of Bioengineering, Chongqing University, Chongqing, China; College of Life Science, Jiangsu Normal University, Xuzhou, Jiangsu Province, China
| | | | | | | | | | | | | | | | | | | | | | | |
Collapse
|
10
|
Enhanced cellular responses to titanium coating with hierarchical hybrid structure. MATERIALS SCIENCE & ENGINEERING. C, MATERIALS FOR BIOLOGICAL APPLICATIONS 2014; 38:272-7. [DOI: 10.1016/j.msec.2014.02.004] [Citation(s) in RCA: 26] [Impact Index Per Article: 2.6] [Reference Citation Analysis] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/11/2013] [Revised: 01/06/2014] [Accepted: 02/04/2014] [Indexed: 11/18/2022]
|
11
|
Rough titanium alloys regulate osteoblast production of angiogenic factors. Spine J 2013; 13:1563-70. [PMID: 23684238 PMCID: PMC3785549 DOI: 10.1016/j.spinee.2013.03.047] [Citation(s) in RCA: 89] [Impact Index Per Article: 8.1] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 03/03/2012] [Revised: 11/28/2012] [Accepted: 03/20/2013] [Indexed: 02/03/2023]
Abstract
BACKGROUND CONTEXT Polyether-ether-ketone (PEEK) and titanium-aluminum-vanadium (titanium alloy) are used frequently in lumbar spine interbody fusion. Osteoblasts cultured on microstructured titanium generate an environment characterized by increased angiogenic factors and factors that inhibit osteoclast activity mediated by integrin α2β1 signaling. It is not known if this is also true of osteoblasts on titanium alloy or PEEK. PURPOSE The purpose of this study was to determine if osteoblasts generate an environment that supports angiogenesis and reduces osteoclastic activity when grown on smooth titanium alloy, rough titanium alloy, or PEEK. STUDY DESIGN This in vitro study compared angiogenic factor production and integrin gene expression of human osteoblast-like MG63 cells cultured on PEEK or titanium-aluminum-vanadium (titanium alloy). METHODS MG63 cells were grown on PEEK, smooth titanium alloy, or rough titanium alloy. Osteogenic microenvironment was characterized by secretion of osteoprotegerin and transforming growth factor beta-1 (TGF-β1), which inhibit osteoclast activity and angiogenic factors including vascular endothelial growth factor A (VEGF-A), fibroblast growth factor 2 (FGF-2), and angiopoietin-1 (ANG-1). Expression of integrins, transmembrane extracellular matrix recognition proteins, was measured by real-time polymerase chain reaction. RESULTS Culture on titanium alloy stimulated osteoprotegerin, TGF-β1, VEGF-A, FGF-2, and angiopoietin-1 production, and levels were greater on rough titanium alloy than on smooth titanium alloy. All factors measured were significantly lower on PEEK than on smooth or rough titanium alloy. Culture on titanium alloy stimulated expression of messenger RNA for integrins that recognize Type I collagen in comparison with PEEK. CONCLUSIONS Rough titanium alloy stimulated cells to create an osteogenic-angiogenic microenvironment. The osteogenic-angiogenic responses to titanium alloy were greater than PEEK and greater on rough titanium alloy than on smooth titanium alloy. Surface features regulated expression of integrins important in collagen recognition. These factors may increase bone formation, enhance integration, and improve implant stability in interbody spinal fusions.
Collapse
|
12
|
Birch MA, Tanaka M, Kirmizidis G, Yamamoto S, Shimomura M. Microporous “Honeycomb” Films Support Enhanced Bone Formation In Vitro. Tissue Eng Part A 2013; 19:2087-96. [DOI: 10.1089/ten.tea.2012.0729] [Citation(s) in RCA: 19] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/09/2023] Open
Affiliation(s)
- Mark A. Birch
- Institute for Cellular Medicine, Newcastle University, Newcastle upon Tyne, United Kingdom
| | - Masaru Tanaka
- Department of Biochemical Engineering, Graduate School of Science and Engineering, Yamagata University, Yonezawa, Japan
| | - George Kirmizidis
- Institute for Cellular Medicine, Newcastle University, Newcastle upon Tyne, United Kingdom
| | - Sadaaki Yamamoto
- Innovation Research Center for Fuel Cells, The University of Electro-Communications, Tokyo, Japan
| | - Masatsugu Shimomura
- Institute of Multidisciplinary Research for Advanced Materials (IMRAM), Tohoku University, Sendai, Japan
| |
Collapse
|
13
|
Kokkinos PA, Koutsoukos PG, Deligianni DD. Detachment strength of human osteoblasts cultured on hydroxyapatite with various surface roughness. Contribution of integrin subunits. JOURNAL OF MATERIALS SCIENCE. MATERIALS IN MEDICINE 2012; 23:1489-1498. [PMID: 22484862 DOI: 10.1007/s10856-012-4628-0] [Citation(s) in RCA: 10] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/25/2011] [Accepted: 03/19/2012] [Indexed: 05/31/2023]
Abstract
Hydroxyapatite (HA) has been widely used as a bone substitute in dental, maxillofacial and orthopaedic surgery and as osteoconductive bone substitute or precoating of pedicle screws and cages in spine surgery. The aim of the present study was to investigate the osteoblastic adhesion strength on HA substrata with different surface topography and biochemistry (pre-adsorption of fibronectin) after blocking of specific integrin subunits with monoclonal antibodies. Stoichiometric HA was prepared by precipitation followed by ageing and characterized by SEM, EDX, powder XRD, Raman spectroscopy, TGA, and specific surface area analysis. Human bone marrow derived osteoblasts were cultured on HA disc-shaped substrata which were sintered and polished resulting in two surface roughness grades. For attachment evaluation, cells were incubated with monoclonal antibodies and seeded for 2 h on the substrata. Cell detachment strength was determined using a rotating disc device. Cell detachment strength was surface roughness, fibronectin preadsorption and intergin subunit sensitive.
Collapse
Affiliation(s)
- Petros A Kokkinos
- Department of Mechanical Engineering and Aeronautics, University of Patras, Rion, Patras, Greece
| | | | | |
Collapse
|
14
|
Birch MA, Johnson-Lynn S, Nouraei S, Wu QB, Ngalim S, Lu WJ, Watchorn C, Yang TY, McCaskie AW, Roy S. Effect of electrochemical structuring of Ti6Al4V on osteoblast behaviour
in vitro. Biomed Mater 2012; 7:035016. [DOI: 10.1088/1748-6041/7/3/035016] [Citation(s) in RCA: 9] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/11/2022]
|
15
|
Olivares-Navarrete R, Hyzy SL, Hutton DL, Dunn GR, Appert C, Boyan BD, Schwartz Z. Role of non-canonical Wnt signaling in osteoblast maturation on microstructured titanium surfaces. Acta Biomater 2011; 7:2740-50. [PMID: 21352958 DOI: 10.1016/j.actbio.2011.02.030] [Citation(s) in RCA: 56] [Impact Index Per Article: 4.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/03/2010] [Revised: 01/18/2011] [Accepted: 02/16/2011] [Indexed: 12/22/2022]
Abstract
The Wnt signaling pathway inhibitor Dickkopf-2 (Dkk2) regulates osteoblast differentiation on microstructured titanium (Ti) surfaces, suggesting involvement of Wnt signaling in this process. To test this, human osteoblast-like MG63 cells were cultured on tissue culture polystyrene or Ti (smooth PT (Ra=0.2 μm), sand-blasted and acid-etched SLA (Ra=3.22 μm), modSLA (hydrophilic SLA)). Expression of Wnt pathway receptors, activators and inhibitors was measured by qPCR. Non-canonical pathway ligands, receptors and intracellular signaling molecules, as well as bone morphogenetic proteins BMP2 and BMP4, were upregulated on SLA and modSLA, whereas canonical pathway members were downregulated. To confirm that non-canonical signaling was involved, cells were cultured daily with exogenous Wnt3a (canonical pathway) or Wnt5a (non-canonical pathway). Alternatively, cells were cultured with antibodies to Wnt3a or Wnt5a to validate that Wnt proteins secreted by the cells were mediating cell responses to the surface. Wnt5a, but not Wnt3a, increased MG63 cell differentiation and BMP2 and BMP4 proteins, suggesting Wnt5a promotes osteogenic differentiation through production of BMPs. Effects of exogenous and endogenous Wnt5a were synergistic with surface microstructure, suggesting the response also depends on cell maturation state. These results indicate a major role for the non-canonical, calcium-dependent Wnt pathway in differentiation of osteoblasts on microstructured titanium surfaces during implant osseointegration.
Collapse
Affiliation(s)
- Rene Olivares-Navarrete
- Wallace H. Coulter Department of Biomedical Engineering at Georgia Tech, Georgia Institute of Technology, 315 Ferst Drive NW, Atlanta, GA 30332-0363, USA
| | | | | | | | | | | | | |
Collapse
|
16
|
Pegueroles M, Aguirre A, Engel E, Pavon G, Gil FJ, Planell JA, Migonney V, Aparicio C. Effect of blasting treatment and Fn coating on MG63 adhesion and differentiation on titanium: a gene expression study using real-time RT-PCR. JOURNAL OF MATERIALS SCIENCE. MATERIALS IN MEDICINE 2011; 22:617-627. [PMID: 21258846 DOI: 10.1007/s10856-011-4229-3] [Citation(s) in RCA: 17] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/30/2009] [Accepted: 01/04/2011] [Indexed: 05/30/2023]
Abstract
Biomaterial surface properties, via alterations in the adsorbed protein layer, and the presence of specific functional groups can influence integrin binding specificity, thereby modulating cell adhesion and differentiation processes. The adsorption of fibronectin, a protein directly involved in osteoblast adhesion to the extracellular matrix, has been related to different physical and chemical properties of biomaterial surfaces. This study used blasting particles of different sizes and chemical compositions to evaluate the response of MG63 osteoblast-like cells on smooth and blasted titanium surfaces, with and without fibronectin coatings, by means of real-time reverse transcription-polymerase chain reaction (qRT-PCR) assays. This response included (a) expression of the α(5), α(v) and α(3) integrin subunits, which can bind to fibronectin through the RGD binding site, and (b) expression of alkaline phosphatase (ALP) and osteocalcin (OC) as cell-differentiation markers. ALP activity and synthesis of OC were also tested. Cells on SiC-blasted Ti surfaces expressed higher amounts of the α(5) mRNA gene than cells on Al(2)O(3)-blasted Ti surfaces. This may be related to the fact that SiC-blasted surfaces adsorbed higher amounts of fibronectin due to their higher surface free energy and therefore provided a higher number of specific cell-binding sites. Fn-coated Ti surfaces decreased α(5) mRNA gene expression, by favoring the formation of other integrins involved in adhesion over α(5)β(1). The changes in α(5) mRNA expression induced by the presence of fibronectin coatings may moreover influence the osteoblast differentiation pathway, as fibronectin coatings on Ti surfaces also decreased both ALP mRNA expression and ALP activity after 14 and 21 days of cell culture.
Collapse
Affiliation(s)
- M Pegueroles
- Biomaterials, Biomechanics, and Tissue Engineering Group, Department of Material Science and Metallurgy, Universitat Politècnica de Catalunya, Av. Diagonal 647, 08028, Barcelona, Spain.
| | | | | | | | | | | | | | | |
Collapse
|
17
|
Role of non-canonical Wnt signaling in osteoblast maturation on microstructured titanium surfaces. Acta Biomater 2011. [PMID: 21352958 DOI: 10.1016/j.actbio.2011.02.03] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.1] [Reference Citation Analysis] [Abstract] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 02/07/2023]
Abstract
The Wnt signaling pathway inhibitor Dickkopf-2 (Dkk2) regulates osteoblast differentiation on microstructured titanium (Ti) surfaces, suggesting involvement of Wnt signaling in this process. To test this, human osteoblast-like MG63 cells were cultured on tissue culture polystyrene or Ti (smooth PT (Ra=0.2 μm), sand-blasted and acid-etched SLA (Ra=3.22 μm), modSLA (hydrophilic SLA)). Expression of Wnt pathway receptors, activators and inhibitors was measured by qPCR. Non-canonical pathway ligands, receptors and intracellular signaling molecules, as well as bone morphogenetic proteins BMP2 and BMP4, were upregulated on SLA and modSLA, whereas canonical pathway members were downregulated. To confirm that non-canonical signaling was involved, cells were cultured daily with exogenous Wnt3a (canonical pathway) or Wnt5a (non-canonical pathway). Alternatively, cells were cultured with antibodies to Wnt3a or Wnt5a to validate that Wnt proteins secreted by the cells were mediating cell responses to the surface. Wnt5a, but not Wnt3a, increased MG63 cell differentiation and BMP2 and BMP4 proteins, suggesting Wnt5a promotes osteogenic differentiation through production of BMPs. Effects of exogenous and endogenous Wnt5a were synergistic with surface microstructure, suggesting the response also depends on cell maturation state. These results indicate a major role for the non-canonical, calcium-dependent Wnt pathway in differentiation of osteoblasts on microstructured titanium surfaces during implant osseointegration.
Collapse
|
18
|
Use of molecular beacons to image effects of titanium surface microstructure on beta1 integrin expression in live osteoblast-like cells. Biomaterials 2010; 31:7640-7. [PMID: 20674005 DOI: 10.1016/j.biomaterials.2010.07.009] [Citation(s) in RCA: 9] [Impact Index Per Article: 0.6] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/22/2010] [Accepted: 07/02/2010] [Indexed: 11/20/2022]
Abstract
This study used molecular beacon technology to examine substrate-dependent changes in integrin subunit expression in living cells. Molecular beacons are oligonucleotide probes that can be delivered into live cells to allow for real-time imaging of mRNA. They have a stem-loop hairpin structure with a fluorophore-quencher pair, which opens when bound to the target mRNA sequence, resulting in a fluorescent signal upon excitation. A novel molecular beacon that is specific to the beta1 integrin subunit mRNA was developed and used to image osteoblast-like MG63 cells in vitro on both glass and titanium surfaces of varying roughness. Specificity was verified by comparing the molecular beacon signal intensities to real-time PCR results in both wild-type cells and cells with shRNA knockdown of beta1 integrin mRNA. The molecular beacon was able to detect changes due to both surface microtopography and silencing of the mRNA target. The results showed that effects of the substrate on beta1 mRNA noted previously in confluent cultures were evident in pre-confluent cells as well, supporting the hypothesis that beta1 integrin pairs are important in proliferation as well as differentiation of osteoblasts. This technique overcomes the limitations of traditional gene assays (PCR, immunofluorescence) by allowing for the real-time measurement and tracking of specific mRNAs in individual live cells prior to confluence.
Collapse
|
19
|
Fang M, Olivares-Navarrete R, Wieland M, Cochran DL, Boyan BD, Schwartz Z. The role of phospholipase D in osteoblast response to titanium surface microstructure. J Biomed Mater Res A 2010; 93:897-909. [PMID: 19705469 DOI: 10.1002/jbm.a.32596] [Citation(s) in RCA: 5] [Impact Index Per Article: 0.4] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/09/2023]
Abstract
Biomaterial surface properties such as microtopography and energy can change cellular responses at the cell-implant interface. Phospholipase D (PLD) is required for the differentiation of osteoblast-like MG63 cells on machined and grit-blasted titanium surfaces. Here, we determined if PLD is also required on microstructured/high-energy substrates and the mechanism involved. shRNAs for human PLD1 and PLD2 were used to silence MG63 cells. Wild-type and PLD1 or PLD1/2 silenced cells were cultured on smooth-pretreatment surfaces (PT); grit-blasted, acid-etched surfaces (SLA); and SLA surfaces modified to have higher surface energy (modSLA). PLD was inhibited with ethanol or activated with 24,25-dihydroxyvitamin-D(3) [24R,25(OH)(2)D(3)]. As surface roughness/energy increased, PLD mRNA and activity increased, cell number decreased, osteocalcin and osteoprotegerin increased, and protein kinase C (PKC) and alkaline phosphatase specific activities increased. Ethanol inhibited PLD and reduced surface effects on these parameters. There was no effect on these parameters after knockdown of PLD1, but PLD1/2 double knockdown had effects comparableto PLD inhibition. 24R,25(OH)(2)D(3) increased PLD activity and the production of osteocalcin and osteoprotegerin, but decreased cell number on the rough/high-energy surfaces. These results confirm that surface roughness/energy-induced PLD activity is required for osteoblast differentiation and that PLD2 is the main isoform involved in this pathway. PLD is activated by 24R,25(OH)(2)D(3) in a surface-dependent manner and inhibition of PLD reduces the effects of surface microstructure/energy on PKC, suggesting that PLD mediates the stimulatory effect of microstructured/high-energy surfaces via PKC-dependent signaling.
Collapse
Affiliation(s)
- Mimi Fang
- Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, Georgia, USA
| | | | | | | | | | | |
Collapse
|
20
|
Raines AL, Olivares-Navarrete R, Wieland M, Cochran DL, Schwartz Z, Boyan BD. Regulation of angiogenesis during osseointegration by titanium surface microstructure and energy. Biomaterials 2010; 31:4909-17. [PMID: 20356623 DOI: 10.1016/j.biomaterials.2010.02.071] [Citation(s) in RCA: 137] [Impact Index Per Article: 9.8] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/14/2010] [Accepted: 02/26/2010] [Indexed: 10/19/2022]
Abstract
Rough titanium (Ti) surface microarchitecture and high surface energy have been shown to increase osteoblast differentiation, and this response occurs through signaling via the alpha(2)beta(1) integrin. However, clinical success of implanted materials is dependent not only upon osseointegration but also on neovascularization in the peri-implant bone. Here we tested the hypothesis that Ti surface microtopography and energy interact via alpha(2)beta(1) signaling to regulate the expression of angiogenic growth factors. Primary human osteoblasts (HOB), MG63 cells and MG63 cells silenced for alpha(2) integrin were cultured on Ti disks with different surface microtopographies and energies. Secreted levels of vascular endothelial growth factor-A (VEGF-A), basic fibroblast growth factor (FGF-2), epidermal growth factor (EGF), and angiopoietin-1 (Ang-1) were measured. VEGF-A increased 170% and 250% in MG63 cultures, and 178% and 435% in HOB cultures on SLA and modSLA substrates, respectively. In MG63 cultures, FGF-2 levels increased 20 and 40-fold while EGF increased 4 and 6-fold on SLA and modSLA surfaces. These factors were undetectable in HOB cultures. Ang-1 levels were unchanged on all surfaces.Media from modSLA MG63 cultures induced more rapid differentiation of endothelial cells and this effect was inhibited by anti-VEGF-A antibodies. Treatment of MG63 cells with 1 alpha,25(OH)(2)D3 enhanced levels of VEGF-A on SLA and modSLA.Silencing the alpha(2) integrin subunit increased VEGF-A levels and decreased FGF-2 levels. These results show that Ti surface microtopography and energy modulate secretion of angiogenic growth factors by osteoblasts and that this regulation is mediated at least partially via alpha(2)beta(1) integrin signaling.
Collapse
Affiliation(s)
- Andrew L Raines
- Parker H. Petit Institute for Bioengineering and Bioscience, Georgia Institute of Technology, Atlanta, GA 30332, USA.
| | | | | | | | | | | |
Collapse
|
21
|
Saito T, Hayashi H, Kameyama T, Hishida M, Nagai K, Teraoka K, Kato K. Suppressed proliferation of mouse osteoblast-like cells by a rough-surfaced substrate leads to low differentiation and mineralization. MATERIALS SCIENCE & ENGINEERING. C, MATERIALS FOR BIOLOGICAL APPLICATIONS 2010. [DOI: 10.1016/j.msec.2009.06.010] [Citation(s) in RCA: 22] [Impact Index Per Article: 1.6] [Reference Citation Analysis] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 10/20/2022]
|
22
|
Abstract
Ion implantation, a common technology in semiconductor processing, has been applied to biomaterials since the 1960s. Using energetic ion bombardment, a general term which includes conventional ion implantation plasma immersion ion implantation (PIII) and ion beam assisted thin film deposition, functionalization of surfaces is possible. By varying and adjusting the process parameters, several surface properties can be attuned simultaneously. Extensive research details improvements in the biocompatibility, mainly by reducing corrosion rates and increasing wear resistance after surface modification. Recently, enhanced bioactivity strongly correlated with the surface topography and less with the surface chemistry has been reported, with an increased roughness on the nanometer scale induced by self-organisation processes during ion bombardment leading to faster cellular adhesion processes.
Collapse
|
23
|
Kirmizidis G, Birch MA. Microfabricated Grooved Substrates Influence Cell–Cell Communication and Osteoblast Differentiation In Vitro. Tissue Eng Part A 2009; 15:1427-36. [DOI: 10.1089/ten.tea.2008.0137] [Citation(s) in RCA: 37] [Impact Index Per Article: 2.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/12/2022] Open
Affiliation(s)
- George Kirmizidis
- Musculoskeletal Research Group, Institute for Cellular Medicine, The Medical School, Newcastle University, Newcastle upon Tyne, United Kingdom
| | - Mark A. Birch
- Musculoskeletal Research Group, Institute for Cellular Medicine, The Medical School, Newcastle University, Newcastle upon Tyne, United Kingdom
| |
Collapse
|
24
|
Mechanisms regulating increased production of osteoprotegerin by osteoblasts cultured on microstructured titanium surfaces. Biomaterials 2009; 30:3390-6. [PMID: 19395022 DOI: 10.1016/j.biomaterials.2009.03.047] [Citation(s) in RCA: 97] [Impact Index Per Article: 6.5] [Reference Citation Analysis] [Abstract] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/09/2009] [Accepted: 03/11/2009] [Indexed: 01/05/2023]
Abstract
Osteoblasts grown on microstructured Ti surfaces enhance osteointegration by producing local factors that regulate bone formation as well as bone remodeling, including the RANK ligand decoy receptor osteoprotegerin (OPG). The objective of this study was to explore the mechanism by which surface microstructure and surface energy mediate their stimulatory effects on OPG expression. Titanium disks were manufactured to present different surface morphologies: a smooth pretreatment surface (PT, Ra<0.2microm), microstructured sandblasted/acid etched surface (SLA, Ra=3-4microm), and a microstructured Ti plasma-sprayed surface (TPS, Ra=4microm). Human osteoblast-like MG63 cells were cultured on these substrates and the regulation of OPG production by TGF-beta1, PKC, and alpha2beta1 integrin signaling determined. Osteoblasts produced increased amounts of OPG as well as active and latent TGF-beta1 and had increased PKC activity when grown on SLA and TPS. Exogenous TGF-beta1 increased OPG production in a dose-dependent manner on all surfaces, and this was prevented by adding blocking antibody to the TGF-beta type II receptor or by reducing TGF-beta1 binding to the receptor by adding exogenous soluble type II receptor. The PKC inhibitor chelerythrine inhibited the production of OPG in a dose-dependent manner, but only in cultures on SLA and TPS. shRNA knockdown of alpha2 or a double knockdown of alpha2beta1 also reduced OPG, as well as production of TGF-beta1. These results indicate that substrate-dependent OPG production is regulated by TGF-beta1, PKC, and alpha2beta1 and suggest a mechanism by which alpha2beta1 signaling increases PKC, resulting in TGF-beta1 production and TGF-beta1 then acts on its receptor to increase transcription of OPG.
Collapse
|
25
|
YAMASHITA D, MACHIGASHIRA M, MIYAMOTO M, TAKEUCHI H, NOGUCHI K, IZUMI Y, BAN S. Effect of surface roughness on initial responses of osteoblast-like cells on two types of zirconia. Dent Mater J 2009; 28:461-70. [DOI: 10.4012/dmj.28.461] [Citation(s) in RCA: 122] [Impact Index Per Article: 8.1] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/23/2022]
|
26
|
Olivares-Navarrete R, Raz P, Zhao G, Chen J, Wieland M, Cochran DL, Chaudhri RA, Ornoy A, Boyan BD, Schwartz Z. Integrin alpha2beta1 plays a critical role in osteoblast response to micron-scale surface structure and surface energy of titanium substrates. Proc Natl Acad Sci U S A 2008; 105:15767-72. [PMID: 18843104 PMCID: PMC2564982 DOI: 10.1073/pnas.0805420105] [Citation(s) in RCA: 179] [Impact Index Per Article: 11.2] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/07/2007] [Indexed: 01/10/2023] Open
Abstract
Efforts to improve bone response to biomaterials have focused on ligands that bind alpha5beta1 integrins. However, antibodies to alpha5beta1 reduce osteoblast proliferation but do not affect differentiation when cells are grown on titanium (Ti). beta1-silencing blocks the differentiation stimulus of Ti microtopography, suggesting that other beta1 partners are important. Stably alpha2-silenced MG63 human osteoblast-like cells were used to test whether alpha2beta1 specifically mediates osteoblast response to Ti surface micron-scale structure and energy. WT and alpha2-silenced MG63 cells were cultured on tissue culture polystyrene (TCPS) and Ti disks with different surface microtopographies: machined pretreatment (PT) surfaces [mean peak to valley roughness (R(a)) < 0.02 microm], PT surfaces that were grit-blasted and acid-etched (SLA; R(a) = 4 microm), and SLA with high surface energy (modSLA). Alkaline phosphatase (ALP), alpha2 and beta1 mRNA, but not alpha5, alpha v, beta3, type-I collagen, or osteocalcin, increased on SLA and modSLA at 6 days. Alpha2 increased at 8 days on TCPS and PT, but remained unchanged on SLA and modSLA. Alpha2-protein was reduced 70% in alpha2-siRNA cells, whereas alpha5-mRNA and protein were unaffected. Alpha2-knockdown blocked surface-dependent increases in beta1 and osteocalcin and decreases in cell number and increases in ALP and local factors typical of MG63 cells grown on SLA and modSLA [e.g., prostaglandin E(2), osteoprotegerin, latent and active TGF-beta1, and stimulatory effects of 1alpha,25(OH)(2)D(3) on these parameters]. This finding indicates that alpha2beta1 signaling is required for osteoblastic differentiation caused by Ti microstructure and surface energy, suggesting that conclusions based on cell behavior on TCPS are not predictive of behavior on other substrates or the mechanisms involved.
Collapse
Affiliation(s)
- R. Olivares-Navarrete
- *Wallace H. Coulter Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, GA 30332
| | - P. Raz
- Department of Periodontics, Hebrew University Hadassah, Jerusalem 91120, Israel
| | - G. Zhao
- *Wallace H. Coulter Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, GA 30332
| | - J. Chen
- Institut Straumann AG, 4052 Basel, Switzerland
| | - M. Wieland
- College of Chemistry and Chemical Engineering, Chongqing University, Chongqing 400044, China; and
| | - D. L. Cochran
- Department of Periodontics, Health Science Center, University of Texas, San Antonio, TX 78229
| | - R. A. Chaudhri
- *Wallace H. Coulter Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, GA 30332
| | - A. Ornoy
- Department of Periodontics, Hebrew University Hadassah, Jerusalem 91120, Israel
| | - B. D. Boyan
- *Wallace H. Coulter Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, GA 30332
| | - Z. Schwartz
- *Wallace H. Coulter Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, GA 30332
- Department of Periodontics, Hebrew University Hadassah, Jerusalem 91120, Israel
| |
Collapse
|
27
|
Schwartz Z, Denison TA, Bannister SR, Cochran DL, Liu YH, Lohmann CH, Wieland M, Boyan BD. Osteoblast response to fluid induced shear depends on substrate microarchitecture and varies with time. J Biomed Mater Res A 2007; 83:20-32. [PMID: 17340600 DOI: 10.1002/jbm.a.31185] [Citation(s) in RCA: 12] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/07/2022]
Abstract
Osteoblasts are exposed to fluid shear in vivo but the effects are not well understood, particularly how substrate properties or length of exposure modify the response. Short exposure (1 h) to shear reduces the stimulatory effect of micron-scale surface structure on osteoblast differentiation, but the effects of longer term exposures are not known. To test the hypothesis that substrate-dependent responses of osteoblasts to shear depend on the length of exposure to fluid flow, MG63 osteoblasts were grown on tissue culture glass, which has an average roughness (Ra) < 0.2 microm; machined Ti disks (PT, Ra < 0.6 microm); Ti disks with a complex microarchitecture [sand blasted acid etched (SLA), Ra = 4-5 microm); and Ti plasma-sprayed surfaces [Ti via plasma spray (TPS), Ra = 7 microm]. Confluent cultures were exposed to pulsatile flow at shear forces of 0, 1, and 14 dynes/cm(2) for 0, 6, 12, and 24 h. Shear reduced cell number on all surfaces, with greatest effects on TPS. Shear had no effect on alkaline phosphatase on smooth surfaces but increased enzyme activity on SLA and TPS in a time-dependent manner. Its effects on osteocalcin, TGF-beta1, and PGE(2) in the conditioned media were greatest on these surfaces as well. Responses to fluid-induced shear were blocked by the general Cox inhibitor indomethacin and the Cox-2 inhibitor meloxicam, indicating that response to shear is mediated by prostaglandin produced via a Cox-2 dependent mechanism. These results show that the effects of fluid induced shear change with time and are substrate dependent, suggesting that substrate microarchitecture regulates the osteoblast phenotype and effects of shear are determined by the maturation state of the responding population.
Collapse
Affiliation(s)
- Z Schwartz
- Wallace H. Coulter Department of Biomedical Engineering, Petit Institute of Bioengineering and Bioscience, Georgia Institute of Technology, Atlanta, Georgia, USA
| | | | | | | | | | | | | | | |
Collapse
|
28
|
Zhao G, Raines AL, Wieland M, Schwartz Z, Boyan BD. Requirement for both micron- and submicron scale structure for synergistic responses of osteoblasts to substrate surface energy and topography. Biomaterials 2007; 28:2821-9. [PMID: 17368532 PMCID: PMC2754822 DOI: 10.1016/j.biomaterials.2007.02.024] [Citation(s) in RCA: 283] [Impact Index Per Article: 16.6] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/13/2006] [Accepted: 02/19/2007] [Indexed: 01/05/2023]
Abstract
OBJECTIVE Surface roughness and surface free energy are two important factors that regulate cell responses to biomaterials. Previous studies established that titanium (Ti) substrates with micron-scale and submicron scale topographies promote osteoblast differentiation and osteogenic local factor production and that there is a synergistic response to micro-rough Ti surfaces that have retained their high surface energy via processing that limits hydrocarbon contamination. This study tested the hypothesis that the synergistic response of osteoblasts to these modified surfaces depends on both surface micro-structure and surface energy. METHODS Ti disks were manufactured to present three different surface structures: smooth pretreatment (PT) surfaces with R(a) of 0.2 microm; acid-etched surfaces (A) with a submicron roughness R(a) of 0.83 microm; and sandblasted/acid-etched surfaces (SLA) with R(a) of 3-4 microm. Modified acid-etched (modA) and modified sandblasted/acid-etched (modSLA) Ti substrates, which have low contamination and present a hydroxylated/hydrated surface layer to retain high surface energy, were compared with regular low surface energy A and SLA surfaces. Human osteoblast-like MG63 cells were cultured on these substrates and their responses, including cell shape, growth, differentiation (alkaline phosphatase, osteocalcin), and local factor production (TGF-beta1, PGE(2), osteoprotegerin (OPG)) were analyzed (N=6 per variable). Data were normalized to cell number. RESULTS There were no significant differences between smooth PT and A surfaces except for a small increase in OPG. Compared to A surfaces, MG63 cells produced 30% more osteocalcin on modA, and 70% more on SLA. However, growth on modSLA increased osteocalcin by more than 250%, which exceeded the sum of independent effects of surface energy and topography. Similar effects were noted when levels of latent TGF-beta1, PGE(2) and OPG were measured in the conditioned media. CONCLUSIONS The results demonstrate a synergistic effect between high surface energy and topography of Ti substrates and show that both micron-scale and submicron scale structural features are necessary.
Collapse
Affiliation(s)
- G Zhao
- Georgia Institute of Technology, Atlanta, GA, USA
| | | | | | | | | |
Collapse
|
29
|
Nebe JGB, Luethen F, Lange R, Beck U. Interface Interactions of Osteoblasts with Structured Titanium and the Correlation between Physicochemical Characteristics and Cell Biological Parameters. Macromol Biosci 2007; 7:567-78. [PMID: 17457937 DOI: 10.1002/mabi.200600293] [Citation(s) in RCA: 47] [Impact Index Per Article: 2.8] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/08/2022]
Abstract
Cellular behavior at the interface of an implant is influenced by the material's topography. However, little is known about the correlation between the biological parameters and the physicochemical characteristics of the biomaterial. We therefore modified pure titanium surfaces by polishing, machining, blasting with glass spheres, blasting with corundum particles, and vacuum plasma spraying to give progressively higher surface roughness. The material surface was characterized by SEM, surface profiling, and electrochemical methods. We revealed a correlation for integrin expression and formation, adhesion, spreading, proliferation, and bone sialo protein expression with the physicochemical parameters of the titanium surfaces.
Collapse
Affiliation(s)
- J G Barbara Nebe
- Department of Internal Medicine, University of Rostock, BMFZ, Schillingallee 69, D-18057 Rostock, Germany.
| | | | | | | |
Collapse
|
30
|
Keselowsky BG, Wang L, Schwartz Z, Garcia AJ, Boyan BD. Integrin alpha(5) controls osteoblastic proliferation and differentiation responses to titanium substrates presenting different roughness characteristics in a roughness independent manner. J Biomed Mater Res A 2007; 80:700-10. [PMID: 17133443 DOI: 10.1002/jbm.a.30898] [Citation(s) in RCA: 102] [Impact Index Per Article: 6.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/30/2023]
Abstract
Integrin alpha(5)beta(1) regulates osteoblast proliferation and differentiation on smooth synthetic surfaces presenting different chemistries, but it is not known whether this integrin controls osteoblast behavior on surfaces that have micron-scale rough topographies. We cultured MG63 human osteoblast-like cells on titanium substrates with three different roughness characteristics: chemically polished (PT), grit blasted and acid etched with a complex topography consisting of 20-100 mum craters and 0.5-2 mum micropits (SLA), and plasma-sprayed Ti with irregular projections (TPS). Cells spread well on PT but displayed a smaller footprint on SLA or TPS. Nuclei were larger on PT as well. alpha(5)beta(1) binding and FAK phosphorylation were greater on the rougher surfaces (TPS > SLA > PT). Antibodies against the alpha(5)beta(1) binding site on fibronectin had no effect on cell number at 3 days, but [(3)H]-thymidine incorporation was increased, suggesting that binding to fibronectin was necessary for cell cycle regulation. Antibodies to the alpha(5) subunit reduced cell number at 3 days on PT and TPS and reduced DNA synthesis on all substrates in a surface microstructure-independent manner. At 7 days, cell numbers were reduced on PT, and DNA synthesis was reduced by 50% on all surfaces. At 7 days, anti-alpha(5) antibodies caused a partial reduction in alkaline phosphatase enzyme activity on all surfaces, but this effect was independent of surface microstructure. These results indicate that surface micron-scale topography modulates alpha(5)beta(1) integrin binding and FAK activation. Signaling via alpha(5)-dependent mechanisms is required for DNA synthesis and regulation of alkaline phosphatase, but this effect is independent of surface microstructure.
Collapse
Affiliation(s)
- B G Keselowsky
- Department of Biomedical Engineering, University of Florida, Gainesville, Florida, USA
| | | | | | | | | |
Collapse
|
31
|
Schwartz Z, Bell BF, Wang L, Zhao G, Olivares-Navarrete R, Boyan BD. Beta-1 integrins mediate substrate dependent effects of 1alpha,25(OH)2D3 on osteoblasts. J Steroid Biochem Mol Biol 2007; 103:606-9. [PMID: 17317155 PMCID: PMC2689367 DOI: 10.1016/j.jsbmb.2006.12.083] [Citation(s) in RCA: 13] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Indexed: 12/01/2022]
Abstract
Surface micron-scale and submicron scale features increase osteoblast differentiation and enhance responses of osteoblasts to 1,25-dihydroxyvitamin D(3) [1alpha,25(OH)(2)D(3)]. beta(1) integrin expression is increased in osteoblasts grown on Ti substrates with rough microarchitecture, and it is regulated by 1alpha,25(OH)(2)D(3) in a surface-dependent manner. To determine if beta(1) has a role in mediating osteoblast response, we silenced beta(1) expression in MG63 human osteoblast-like cells using small interfering RNA (siRNA). In addition, MG63 cells were treated with two different monoclonal antibodies to human beta(1) to block ligand binding. beta(1)-silenced MG63 cells grown on a tissue culture plastic had reduced alkaline phosphatase activity and levels of osteocalcin, transforming growth factor beta(1), prostaglandin E(2), and osteoprotegerin in comparison with control cells. Moreover, beta(1)-silencing inhibited the effects of surface roughness on these parameters and partially inhibited effects of 1alpha,25(OH)(2)D(3). Anti beta(1) antibodies decreased alkaline phosphatase but increase osteocalcin; effects of 1alpha,25(OH)(2)D(3) on cell number and alkaline phosphatase were reduced and effects on osteocalcin were increased. These findings indicate that beta(1) plays a major and complex role in osteoblastic differentiation modulated by either surface microarchitecture or 1alpha,25(OH)(2)D(3). The results also show that beta(1) mediates, in part, the synergistic effects of surface roughness and 1alpha,25(OH)(2)D(3).
Collapse
Affiliation(s)
- Zvi Schwartz
- Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, Georgia, USA
- Department of Periodontics, Hebrew University Hadassah, Jerusalem, Israel
| | - Bryan F. Bell
- Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, Georgia, USA
| | - Liping Wang
- Department of Orthopaedics, Stanford University Medical School, Palo Alto, California
| | - Ge Zhao
- Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, Georgia, USA
| | - Rene Olivares-Navarrete
- Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, Georgia, USA
| | - Barbara D. Boyan
- Department of Biomedical Engineering, Georgia Institute of Technology, Atlanta, Georgia, USA
| |
Collapse
|
32
|
Abstract
Many of our current therapies are based on information obtained in cell cultures using substrates that have little in common with the substrates the cells will encounter in vivo. To produce materials that are clinically valuable, we must analyze more deeply how musculoskeletal cells interact with the physical features of their environments. An increasing body of information has examined the mechanisms by which osteoblasts interact with their substrate. The underlying substrate, particularly in bone, also has structural features that can alter the mechanical environment experienced by the cells. These structural features modulate the nature of cell attachment and the resulting cell shape, affecting cell proliferation and differentiation. The chemistry, surface energy, and microarchitecture of a material all influence the kinds of proteins that adsorb onto the surface, which in turn affects integrin-mediated attachment. Signaling via integrins initiates the transfer of information to the cell about the microenvironment. Cells can differentiate between crystallinities of the same chemistry and distinguish complex differences in surface structure. These differences in the in vitro response correspond to differences in clinical effectiveness. By designing biomaterials that maximally enhance mesenchymal cell attachment, migration, proliferation, and differentiation, the value of these materials for tissue repair will be markedly increased. The goal is to provide materials that are capable of supporting tissue regeneration in vivo, often at sites compromised by infection and loss of structure.
Collapse
Affiliation(s)
- Barbara D Boyan
- Wallace H. Coulter Department of Biomedical Engineering, Georgia Tech., Atlanta, GA, USA
| | | |
Collapse
|