Porous carbon derived from aluminum-based metal organic framework as a fiber coating for the solid-phase microextraction of polycyclic aromatic hydrocarbons from water and soil

A highly porous fiber coating based on a Zn-MOF/COF hybrid material for solid-phase microextraction of PAHs in soil

This study involved the development of a novel adsorbent by combining a Zn-based MOF with a melamine-based COF, resulting in the formation of a hybrid material known as Zn-MOF/COF. The adsorbent was characterized using FT-IR, SEM, XRD, EDX, and BET analysis techniques. The resulting Zn-MOF/COF sorbent was employed to prepare solid-phase microextraction (SPME) fibers for the extraction and enrichment of polycyclic aromatic hydrocarbons (PAHs) in contaminated soil samples, after coupling with GC-FID. A Box-Behnken design (BBD) was used to optimize key variables of SPME conditions. Under optimal conditions of 85 °C for 30 min extraction with 23 μL g-1 sample's moisture level, linear responses of six PAHs were ranging from 1 to 20000 ng g⁻1 with determination coefficients greater than 0.99. Limits of detection (LODs) were over the ranges of 0.1-1 ng g-1. The RSDs for intra-fiber and inter-fiber analyses were obtained 2.2-6.6% and 5.2-11.6%, respectively. Relative recoveries values for real soil samples were found to be 91.1-110.2%. The results showed lower cost and higher extraction efficiency for the Zn-MOF/COF fiber, compared with commercial and homemade adsorbents.

Hierarchical covalent organic framework hollow nanofibers-bonded stainless steel fiber for efficient solid phase microextraction

The solid phase microextraction (SPME) technique has been widely applied in the detection of trace compounds in food, environment, and medicine due to its advantages of easy quantification, simple operation, and greenness. Herein, a templating strategy with SiO2 nanofibers (SiO2 NFs) is reported to synthesize hierarchical covalent organic framework hollow nanofibers (COF HNFs)-coated stainless steel fiber for SPME application with dramatically enhanced enrichment performance for trace analytes. The construction of hierarchical porosity inside the microextraction coatings can not only increase the specific surface area of COF extraction materials for obtaining more abundant adsorption sites but also greatly improve the accessibility of internal COF micropores. Moreover, the thicknesses of the microextraction COF coatings can be facilely tailored by adjusting the amount of SiO2 NFs pre-assembled on the SPME fibers. On the headspace solid phase microextraction (HS-SPME) of antimicrobial residues, the developed COF TpBD-Me2 HNFs-12 fibers achieve enrichment factors of 2026 and 1823 for thymol and carvacrol respectively, which are significantly higher than those obtained from the counterpart COF TpBD-Me2-bonded fiber (8.5-8.2 times) and commercial CAR/PDMS fiber (3.3-4.4 times). Furthermore, the developed method was demonstrated to have wide linearity (0.1-50 μg L-1), low limits of detection (0.010 μg L-1), good thermal stability and excellent reusability (>60 recycles), demonstrating great application potential in the extraction of trace organic pollutants. The strategy developed in this work is applicable to preparing a variety of topological COF (e.g., TpBD, TpPa-1) HNFs-bonded fibers.

Nanoporous carbon fiber derived from Cu-BDC metal organic framework @pencil graphite as a sorbent for solid phase microextraction of acetamiprid and imidacloprid

Solid-phase microextraction (SPME) is a sample pretreatment technique for enrichment of trace level of compounds from complex matrices. The fiber coating, as an extraction phase, is the significant part of SPME, which specifying the analytical performance of the developed SPME. In this study, a novel in situ fabricated Cu@porous carbon fiber that derived from copper benzene-1,4-dicarboxylate framework@pencil graphite (Cu-BDC MOF@PG) fiber was prepared as a SPME fiber. The Cu-BDC MOF was electrodeposited on the surface of pencil graphite. The Cu@porous carbon fiber with nanoporous structure was constructed by the direct carbonization of the electrosynthesized fiber. The Cu@porous carbon fiber showed high analytical performance for direct immersion SPME (DI-SPME) of acetamiprid and imidacloprid in fruit and vegetable samples. The SPME method was coupled by high-performance liquid chromatography-ultraviolet detection (SPME-HPLC-UV) for determination of the analytes. Under the optimized condition, good linear ranges (1-500 μg L-1 and 0.5-200 μg L-1) and acceptable limits of detection (LODs = 0.30 and 0.15 μg L-1), appropriate spiking recoveries in the range 87-109.0% were attained for acetamiprid and imidacloprid, respectively. Intra- and inter-day relative standard deviations were found within the ranges of 2.35-3.46% and 3.30-3.70%, respectively. These results signify promising potential of the in situ fabricated porous carbon fiber for SPME applications. Considering that most of the pencil graphite is made of carbon, after the carbonization of the Cu-BDC MOF@PG fiber, a unified porous carbon fiber is obtained. Compared to other reported procedures, in situ direct carbonization of Cu-BDC MOF@PG fiber was a one-step and straightforward method to fabricate carbon fiber.

Sponge-like porous manganese(II, III) oxide as a coating for solvent-assisted solid-phase microextraction of polycyclic aromatic hydrocarbons followed by gas chromatography-mass spectrometry

A nanostructure sponge-like porous manganese(II, III) oxide was synthesized and applied as a new fiber coating for solvent-assisted solid-phase microextraction. The synthesized material was characterized via Fourier-transform infrared spectroscopy, scanning electron microscopy, thermogravimetric analysis, X-ray diffraction, and N₂ adsorption/desorption techniques. To investigate the extraction performance of the prepared material, direct immersion solid-phase microextraction followed by gas chromatography-mass spectrometry was used for the determination of the selected polycyclic aromatic hydrocarbons in wastewater samples. Three polycyclic aromatic hydrocarbons including 1-methylnaphthalene, anthracene, and pyrene were selected as model analytes. To maximize the sensitivity of the method, key experimental factors affecting the extraction efficiency of the analytes such as ionic strength, extraction solvent, stirring rate, extraction temperature and time, and desorption temperature and time were optimized. The applicability of the new coating material for the extraction of the selected analytes from wastewater samples was evaluated. Under the optimum conditions, detection limits between 0.7 and 1.5 ng L^-1 were obtained for the model analytes. The linear dynamic range was 5.0-3.0 × 10³ ng L^-1 for all the analytes. Relative standard deviations were between 2 and 11%. In the case of real sample analysis, the extraction recoveries of the analytes were obtained in the range of 77-111%.

Polycyclic aromatic hydrocarbon contamination in soils and sediments: Sustainable approaches for extraction and remediation

Polycyclic aromatic hydrocarbons (PAHs) are carcinogenic environmental pollutants that are extremely hydrophobic in nature and resistant to biological degradation. Extraction of PAHs from environmental matrices is the first and most crucial step in PAH quantification. Extraction followed by quantification is essential to understand the extent of contamination prior to the application of remediation approaches. Due to their non-polar structures, PAHs can be adsorbed tightly to the organic matter in soils and sediments, making them more difficult to be extracted. Extraction of PAHs can be achieved by a variety of methods. Techniques such as supercritical and subcritical fluid extraction, microwave-assisted solvent extraction, plant oil-assisted extraction and some microextraction techniques provide faster PAH extraction using less organic solvents, while providing a more environmentally friendly and safer process with minimum matrix interferences. More recently, more environmentally friendly methods for soil and sediment remediation have been explored. This often involves using natural chemicals, such as biosurfactants, to solubilize PAHs in contaminated soils and sediments to allow subsequent microbial degradation. Vermiremediation and microbial enzyme-mediated remediation are emerging approaches, which require further development. The following summarises the existing literature on traditional PAH extraction and bioremediation methods and contrasts them to newer, more environmentally friendly ways.

On the use of metal-organic frameworks for the extraction of organic compounds from environmental samples

The determination of trace metals and organic contaminants in environmental samples, such as water, air, soil, and sediment, is until today a challenging process for the analytical chemistry. Metal-organic frameworks (MOFs) are novel porous nanomaterials that are composed of metal ions and an organic connector. These materials are gaining more and more attention due to their superior characteristics, such as high surface area, tunable pore size, mechanical and thermal stability, luminosity, and charge transfer ability between metals and ligands. Among the various applications of MOFs are gas storage, separation, catalysis, and drug delivery. Recently, MOFs have been successfully introduced in the field of sample preparation for analytical chemistry and they have been used for sample pretreatment of various matrices. This review focuses on the applications of MOFs as novel adsorbents for the extraction of organic compounds from environmental samples.

Metal organic framework derived Zn/N co-doped hydrophilic porous carbon for efficient solid phase microextraction of polar phenols

MOF-derived zink and nitrogen co-doped porous carbon (ZNPC) was synthesized through the pyrolysis of MOF-5-NH₂ and used as a solid-phase microextraction (SPME) coating material. Coupled with gas chromatography-mass spectrometry (GC-MS), headspace SPME (HS-SPME) based on ZNPC was adopted for the determination of phenols in food samples. The co-existence of N and Zn in ZNPC endows the derived carbon superior hydrophilicity, which is highly beneficial for phenols capture. After optimizing the conditions of extraction and desorption, a sensitive analytical method was established with low limits of detections (LODs, 0.73-2.3 ng g^-1) and wide linear ranges (5-5000 ng g^-1). Both the intra-fiber repeatability (RSDs from 2.8-7.3%) and inter-fiber reproducibility (RSDs from 9.7-11.7%) were satisfactory. The established method was applied to phenol determination in beef jerky and duck neck with satisfactory recoveries of 81.2-120.4% and RSDs of 2.8-9.9%, which met well with the requirement of practical application.

Recent Advances in the Extraction of Polycyclic Aromatic Hydrocarbons from Environmental Samples

Polycyclic aromatic hydrocarbons (PAHs) comprise a group of chemical compounds consisting of two or more fused benzene rings. PAHs exhibit hydrophobicity and low water solubility, while some of their members are toxic substances resistant to degradation. Due to their low levels in environmental matrices, a preconcentration step is usually required for their determination. Nowadays, there is a wide variety of sample preparation techniques, including micro-extraction techniques (e.g., solid-phase microextraction and liquid phase microextraction) and miniaturized extraction techniques (e.g., dispersive solid-phase extraction, magnetic solid-phase extraction, stir bar sorptive extraction, fabric phase sorptive extraction etc.). Compared to the conventional sample preparation techniques, these novel techniques show some benefits, including reduced organic solvent consumption, while they are time and cost efficient. A plethora of adsorbents, such as metal-organic frameworks, carbon-based materials and molecularly imprinted polymers, have been successfully coupled with a wide variety of extraction techniques. This review focuses on the recent advances in the extraction techniques of PAHs from environmental matrices, utilizing novel sample preparation approaches and adsorbents.

Recent Applications and Newly Developed Strategies of Solid-Phase Microextraction in Contaminant Analysis: Through the Environment to Humans

The present review aims to describe the recent and most impactful applications in pollutant analysis using solid-phase microextraction (SPME) technology in environmental, food, and bio-clinical analysis. The covered papers were published in the last 5 years (2014–2019) thus providing the reader with information about the current state-of-the-art and the future potential directions of the research in pollutant monitoring using SPME. To this end, we revised the studies focused on the investigation of persistent organic pollutants (POPs), pesticides, and emerging pollutants (EPs) including personal care products (PPCPs), in different environmental, food, and bio-clinical matrices. We especially emphasized the role that SPME is having in contaminant surveys following the path that goes from the environment to humans passing through the food web. Besides, this review covers the last technological developments encompassing the use of novel extraction coatings (e.g., metal-organic frameworks, covalent organic frameworks, PDMS-overcoated fiber), geometries (e.g., Arrow-SPME, multiple monolithic fiber-SPME), approaches (e.g., vacuum and cold fiber SPME), and on-site devices. The applications of SPME hyphenated with ambient mass spectrometry have also been described.

Covalent Organic Framework as Fiber Coating for Solid-Phase Microextraction of Chlorophenols Followed by Quantification with Gas Chromatography-Mass Spectrometry

Headspace solid-phase microextraction coupled with gas chromatography-mass spectrometry was adopted for the simultaneous determination of seven chlorophenols (CPs) from honey and canned-yellow-peach samples. A covalent organic framework made of 1,3,5-triformylphloroglucinol (Tp) and benzidine (BD) was used as the SPME fiber coating to preconcentrate the acetylation derivatives of the CPs. The main experimental parameters including derivatization conditions, extraction temperature and time, headspace volume, salt concentration, and desorption temperature were investigated. The fiber showed a high extraction capability for the CPs. The limits of detection (LODs) for the analytes were 0.3-0.7 μg kg^-1 for honey and 0.8-1.8 μg kg^-1 for canned-yellow-peach samples, suggesting good sensitivity for the method. The response linearity was 2.4-250 μg kg^-1 for 2-CP and 3,4-CP and 1.0-150 μg kg^-1 for the other remaining analytes in the honey samples. For the canned-yellow-peach samples, the response linearity was 6.0-300 μg kg^-1 for 2-CP and 3,4-CP and 3.0-200 μg kg^-1 for the others. The correlation coefficients were higher than 0.9919. Good repeatability (RSD < 11.9%) for the method and high recoveries (70.2-113%) of the analytes were observed under the optimal conditions. The established method was satisfactorily applied for the analysis of honey and canned-yellow-peach samples.

Recent advances in metal-organic frameworks for adsorption of common aromatic pollutants

This review (with 85 refs.) summarizes the recent literature on the adsorption of common aromatic pollutants by using modified metal-organic frameworks (MOFs). Four kinds of aromatic pollutants are discussed, namely benzene homologues, polycyclic aromatic hydrocarbons (PAHs), organic dyes and their intermediates, and pharmaceuticals and personal care products (PPCPs). MOFs are shown to be excellent adsorbents that can be employed to both the elimination of pollutants and to their extraction and quantitation. Adsorption mechanisms and interactions between aromatic pollutants and MOFs are discussed. Finally, the actual challenges of existence and the perspective routes towards future improvements in the field are addressed. Graphical abstract Recent advance on adsorption of common aromatic pollutants including benzene series, polycyclic aromatic hydrocarbons, organic dyes and their intermediates, pharmaceuticals and personal care products by metal-organic frameworks.

A chromium(III) oxide-coated steel wire prepared by arc ion plating for use in solid-phase microextraction of aromatic hydrocarbons

The authors introduce an arc ion plating method for the deposition of chromium oxide (Cr₂O₃) on a steel wire substrate, and its use as a coating for solid phase microextraction. The coating has a micro- and nano-scaled structure after annealing at 700 °C. It is found that Cr₂O₃ exhibits a good extraction capability for the aromatic hydrocarbons naphthalene, anthracene, fluorene, fluoranthene, and biphenyl. Following desorption by high temperature at 300 °C, the analytes were quantified by gas chromatography (GC). The limits of detection are in the range between 20 and 200 ng·L^-1, and calibration plots are linear within a wide range (0.2 to 400 μg·L^-1). The coating has excellent mechanical properties, with a hardness is as high as 31.7 GPa, and the adhesion strength between coating and substrate reaches 20.1 N (corresponding to the critical Hertzian contact stress of 10 GPa). This, along with the chemical and thermal stability of the Cr₂O₃ coating, endows the wire with a long operational life. It was used for at least 100 times without any obvious decline of extraction capability. Graphical abstract An arc ion plating method was introduced for the deposition of chromium oxide (Cr₂O₃) on a steel wire substrate, and its use as a coating for solid phase microextraction with high mechanical strength, stability, and long operational lifetime.

Recent advances in metal-organic frameworks and covalent organic frameworks for sample preparation and chromatographic analysis

In the field of analytical chemistry, sample preparation and chromatographic separation are two core procedures. The means by which to improve the sensitivity, selectivity and detection limit of a method have become a topic of great interest. Recently, porous organic frameworks, such as metal-organic frameworks (MOFs) and covalent organic frameworks (COFs), have been widely used in this research area because of their special features, and different methods have been developed. This review summarizes the applications of MOFs and COFs in sample preparation and chromatographic stationary phases. The MOF- or COF-based solid-phase extraction (SPE), solid-phase microextraction (SPME), gas chromatography (GC), high-performance liquid chromatography (HPLC) and capillary electrochromatography (CEC) methods are described. The excellent properties of MOFs and COFs have resulted in intense interest in exploring their performance and mechanisms for sample preparation and chromatographic separation.

Electrodeposition of self-assembled poly(3,4-ethylenedioxythiophene) @gold nanoparticles on stainless steel wires for the headspace solid-phase microextraction and gas chromatographic determination of several polycyclic aromatic hydrocarbons

In this work, a novel poly(3,4-ethylenedioxythiophene)@Au nanoparticles (PEDOT@AuNPs) hybrid coating was prepared and characterized. Firstly, the monomer 3,4-ethylenedioxythiophene was self-assembled on AuNPs, and then electropolymerization was performed on a stainless steel wire by cyclic voltammetry. The obtained PEDOT@AuNPs coating was rough and showed cauliflower-like micro-structure with thickness of ∼40μm. It displayed high thermal stability (up to 330°C) and mechanical stability and could be used for at least 160 times of solid phase microextraction (SPME) without decrease of extraction performance. The coating exhibited high extraction capacity for some environmental pollutants (e.g. naphthalene, 2-methylnaphthalene, acenaphthene, fluorene and phenathrene) due to the hydrophobic interaction between the analytes and PEDOT and the additional physicochemical affinity between polycyclic aromatic hydrocarbons and AuNPs. Through coupling with GC detection, good linearity (correlation coefficients higher than 0.9894), wide linear range (0.01-100μgL^-1), low limits of detection (2.5-25ngL^-1) were achieved for these analytes. The reproducibility (defined as RSD) was 1.1-4.0% and 5.8-9.9% for single fiber (n=5) and fiber-to-fiber (n=5), respectively. The SPME-GC method was successfully applied for the determination of three real samples, and the recoveries for standards added were 89.9-106% for lake water, 95.7-112% for rain water and 93.2-109% for soil saturated water, respectively.

Preparation and Properties of Metal Organic Framework/Activated Carbon Composite Materials

Metal organic frameworks (MOFs) have unique properties that make them excellent candidates for many high-tech applications. Nevertheless, their nonconducting character is an obstacle to their practical utilization in electronic and energy systems. Using the familiar HKUST-1 MOF as a model, we present a new method of imparting electrical conductivity to otherwise nonconducting MOFs by preparing MOF nanoparticles within the conducting matrix of mesoporous activated carbon (AC). This composite material was studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), gas adsorption measurements, and electron paramagnetic resonance (EPR) spectroscopy. We show that MOF nanoparticles grown within the carbon matrix maintain their crystalline characteristics and their surface area. Surprisingly, as a result of the composition process, EPR measurements revealed a copper signal that had not yet been achieved. For the first time, we could analyze the complex EPR response of HKUST-1. We demonstrate the high conductivity of the MOF composite and discuss various factors that are responsible for these results. Finally, we present an optional application for using the conductive MOF composite as a high-performance electrode for pseudocapacitors.

A porous carbon derived from amino-functionalized material of Institut Lavoisier as a solid-phase microextraction fiber coating for the extraction of phthalate esters from tea

In this work, a porous carbon derived from amino-functionalized material of Institut Lavoisier (C-NH2 -MIL-125) was prepared and coated onto a stainless-steel wire through sol-gel technique. The coated fiber was used for the solid-phase microextraction of trace levels of phthalate esters (diallyl phthalate, di-iso-butyl ortho-phthalate, di-n-butyl ortho-phthalate, benzyl-n-butyl ortho-phthalate, and bis(2-ethylhexy) ortho-phthalate) from tea beverage samples before gas chromatography with mass spectrometric analysis. Several experimental parameters that could influence the extraction efficiency such as extraction time, extraction temperature, sample pH, sample salinity, stirring rate, desorption temperature and desorption time, were investigated. Under the optimal conditions, the linearity existed in the range of 0.05-30.00 μg/L for green jasmine tea beverage samples, and 0.10-30.00 μg/L for honey jasmine tea beverage samples, with the correlation coefficients (r) ranging from 0.9939 to 0.9981. The limits of detection of the analytes for the method were 2.0-3.0 ng/L for green jasmine tea beverage sample, and 4.0-5.0 ng/L for honey jasmine tea beverage sample, depending on the compounds. The recoveries of the analytes for the spiked samples were in the range of 82.0-106.0%, and the precision, expressed as the relative standard deviations, was less than 11.1%.