Biodegradable microplastics (BMPs): a new cause for concern?

Microbial plankton uptake enhances the degradation of a biodegradable microplastic

The use of biodegradable plastics as an alternative to conventional non-degradable synthetic polymers is gaining market to reduce plastic pollution, however, their biodegradability is not unconditional. In this study, we hypothesized that planktonic protists (nanoflagellates and ciliates) increase the degradation of the biodegradable PLGA (poly(lactic-co-glycolic) acid) due to particle uptake. We conducted uptake and degradation experiments using PLGA microspheres of 4.9 ± 2.8 μm diameter and the microbial planktonic community from the Baltic Sea. We found that planktonic protists ingested PLGA of different sizes, with ciliates displaying higher clearance rates and ingesting larger particles compared to nanoflagellates. In addition, we observed a more pronounced decrease in PLGA concentration and particle size over time in the presence of seawater containing microbial plankton compared to a control with only ultrapure water, suggesting that the presence of these organisms increases the rate of degradation of PLGA in marine ecosystems. Altogether, these results indicate that microbial plankton enhances the degradation of biodegradable microplastics like PLGA, specifically through rapid uptake by planktonic protists. These findings highlight the role of particle ingestion by planktonic protists in the fate of the so-called biodegradable plastics when they enter aquatic ecosystems.

Acute and partial life-cycle toxicity of a tri-polymer blend of microplastics in the copepod Acartia tonsa

Microplastics are a prolific environmental contaminant that pose a risk to marine organisms. Ecotoxicological studies have identified microplastics can cause sub-lethal harm to aquatic biota. However, prior studies often lack comparability and environmental relevance, for example focussing upon monodisperse beads at extremely high concentrations. Copepods are keystone marine taxa that play vital roles in the marine food web and biogeochemical cycling. In this study, we adapted ISO methods to conduct acute and partial life-cycle toxicity tests exposing adult and juvenile life stages of the copepod Acartia tonsa to a fully characterised tri-polymer microplastic blend comprising cryoground polyethylene, polypropylene, and nylon particles (5-100 μm) at concentrations ranging 0-1000 μg L-1. The tests considered the toxicity of microplastics on a wide number of endpoints including adult survival, algal ingestion rates, egg production and size, larval development ratio and juvenile survival. Mortality, egg size and larval development ratio proved to be the most sensitive endpoints. The tri-polymer blend had an LC5072h value of 182 μg L-1 providing a baseline for future toxicity testing using this method.

cAMP-Mediated Biofilm eDNA Transfer Facilitates the Resilience of Soil Microbiome to Agrochemical Stress

Soil microorganisms utilize extracellular DNA (eDNA)-based biofilms as a defense against xenobiotics. However, the specific effects and transfer pathways of eDNA under persistent agrochemical exposure remain unclear. This study examined the transfer dynamics of carbofuran-hydrolase gene pchA from Pseudomonas stutzeri PS21. During biofilm formation, pchA was released from eDNA, leading to an enrichment of beneficial microorganisms such as Acidobacteria and Elusimicrobia, which enhanced organic compound metabolism and improved soil microbiome resilience. An increase in the pchA-associated mobile genetic elements and the colocalization of pchA with other bacterial species indicated the potential horizontal gene transfer (HGT) under carbofuran exposure. Additionally, carbofuran triggered a cAMP-dependent apoptotic pathway, leading to a 59.6% increase in pchA copy number, which suggested that cAMP played a role in initiating HGT. In conclusion, the cAMP-mediated interspecific transfer of pchA could enhance microbial coadaptation to carbofuran contamination, thereby strengthening the collective defense of soil microbiome against agrochemical stress.

Determining Antimicrobial Resistance in the Plastisphere: Lower Risks of Nonbiodegradable vs Higher Risks of Biodegradable Microplastics

The plastisphere is a potential contributor to global antimicrobial resistance (AMR), posing potential threats to public and environmental health. However, comprehensively quantifying the contribution of microplastics with different biodegradability to AMR is lacking. In this study, we systematically quantified AMR risk mediated by biodegradable and nonbiodegradable microplastics using abundance-based methods and a custom AMR risk ranking framework that includes antimicrobial resistance genes (ARGs) abundance, mobility, and host pathogenicity. Our results demonstrated that biodegradable microplastics exhibited higher AMR risk compared to that of nonbiodegradable plastics. Key resistance genes, including those for multidrug, bacitracin, and aminoglycoside resistance, were predominant. Machine learning analysis identified cell motility as the most significant signature associated with AMR risk, highlighting its potential role in promoting ARGs dissemination. In addition, biodegradable microplastics promoted oxidative stress and SOS responses, which likely enhanced horizontal gene transfer (HGT) and AMR. Metagenome-assembled genomes (MAGs) analysis uncovered the colocalization of microplastic degradation genes, ARGs, and virulence factors (VFs), further supporting the elevated risk in biodegradable plastisphere. The proximity of ARGs to mobile genetic elements (MGEs) suggests that microplastic degradation processes might favor ARGs mobility. These findings would contribute critical insights into AMR dissemination in the plastisphere, emphasizing the need for integrated environmental and public health strategies under the context of One Health.

First evidence of molecular response of the shrimp Hippolyte inermis to biodegradable microplastics

The increasing demand for sustainable alternatives to conventional plastics has propelled the interest in bioplastics. A few papers reported on the effects of plastics on crustaceans, but no indication about biodegradable polymers is available. Hippolyte inermis Leach, 1816 is a protandric shrimp commonly living on leaves of the seagrass Posidonia oceanica, in the Mediterranean Sea. This crustacean is typically chosen as a model to study sex differentiation processes. Here, we demonstrated its convenience as a model organism to study the effects of biodegradable polymers (BPs). Five BPs were studied: polybutylene succinate (PBS), polybutylene succinate-co-butylene adipate (PBSA), polycaprolactone (PCL), poly-3-hydroxybutyrates (PHB) and polylactic acid (PLA). Larvae of H. inermis were exposed to three concentrations of each BP (1, 5 and 10 mg/L, respectively) for ten days. After exposure, the expression levels of eighteen genes involved in stress response and detoxification processes, retrieved from a H. inermis transcriptomic library, were validated by Real Time qPCR. This study is the first using a molecular approach to detect H. inermis responses to contaminants and in particular to biodegradable polymers, through the evaluation of functional gene's pathways.

Disintegration of commercial biodegradable plastic products under simulated industrial composting conditions

Biodegradable plastics are often promoted as sustainable alternatives to conventional plastics. Nevertheless, significant knowledge gaps exist regarding their degradation under relevant conditions, particularly when compounded into commercial products. To this end, the present research investigates the disintegration of ten commercially available biodegradable plastic products under simulated industrial composting conditions. The tested products included polymer compositions of either polylactic acid (PLA), polybutylene adipate terephthalate (PBAT)/starch, or polyhydroxyalkanoate (PHA), covering both flexible and rigid plastics. These products comprised three waste bags, one waste bag drawstring, one food bag (flexible plastics), two flower pots, one food container, one plate, and one lid (rigid plastics). Among the tested products, nine were marketed as compostable. Of these, six were certified under the European standard EN 13432 for compostable packaging, two held TÜV Austria's "OK compost home" certification, and one was labeled as compostable but lacked certification. Additionally, one product was labeled as 100% biodegradable but lacked certification, and the environment in which the product could biodegrade was not specified. Disintegration was determined according to ISO 20200 in laboratory scale tests conducted at 58 °C with 55% moisture content over 90 days. Results showed disintegration degrees ranging from 75 to 100%, with five products achieving complete disintegration. Two products, however, reached only 75% disintegration. Following the disintegration test, compost particles smaller than 2 mm were examined for microplastics (MPs) via light microscopy. MPs were detected in compost undersieves for two of the ten biodegradable plastic products, while no MPs were detected for the conventional plastics. Notably, the visual inspection was performed without pretreating the compost matrix due to the observed degradation of biodegradable plastics when using chemicals for oxidative digestion. Considering the limitations of visual MP observation without pretreatment, future research should prioritize the development of methods for extracting biodegradable MPs from complex matrices like compost. Enhanced extraction methods are essential for understanding compost's potential role as a source of MPs in the environment.

Changes in the spectroscopic response of soil organic matters by PBAT microplastics regulated the Cd adsorption behaviors in different soils

Contamination of microplastics (MPs) and heavy metals occurs frequently in terrestrial ecosystems, but their interactions remain unclear. A 60-day incubation experiment was conducted to study the behaviors of cadmium (Cd) in polybutylene adipate terephthalate (PBAT) MPs-contaminated soils, with different doses (1, 10%) and sizes (150-300 and 75-150 μm). Soil chemical properties, including the three-dimensional fluorescence of dissolved organic matter (DOM) and microbial diversity in both farmland and woodland soils were analyzed. Results showed that soil properties, especially the components and fluorescence characteristics of DOM varied with soil types and PBAT properties. Higher soil chemical properties and microbial diversity were found in woodland soils. The soluble microbial by-product substances and humic acid-like substance were dominated in soil DOM, while the proportions of fulvic/humic-acid like substances and soil humification decreased with the addition of 10% PBAT. Soil microbial diversity increased with doses of PBAT, but not sensitive to the sizes of PBAT. The adsorption capacity of Cd decreased with the addition of PBAT, especially in the 10% and 75-150 μm PBAT treatments. Both Langmuir and Freundlich models fitted well with the adsorption isotherms of Cd. Multiple correlation analyses showed that low molecular weight fractions, humus index of DOM and soil microbial diversity such as Shannon, Simpson, and Pielou all positively correlated with the adsorption behaviors of Cd in PBAT-contaminated soils. Biodegradable MPs can change soil quality and promote the release of soil Cd, which deserves further research attention.

The impact of biodegradable plastics on methane and carbon dioxide emissions in soil ecosystems: a Fourier transform infrared spectroscopy approach

Biodegradable plastics (BPs), promising eco-friendliness, raise environmental concerns as they degrade into numerous microplastics (Bio-MPs). The impact of Bio-MPs on methane (CH4) and carbon dioxide (CO2) emissions in soil ecosystems remains largely unexplored. Utilizing Fourier transform infrared (FTIR) spectroscopy, we innovatively designed a circulating system, integrating a long optical-path gas cell with a static chamber for continuous and convenient CH4/CO2 monitoring in paddy soils with the addition of Bio-MPs (PBAT). On the 7th day of incubation, we observed a significant increase in CH4/CO2 absorption peaks due to the addition of PBAT, with enhancements of 92-fold and 213-fold, respectively. Built upon this system, we explored a quantitative method based on the main absorption peak (3010 cm-1) for CH4, and calculated cumulative emissions. Additionally, we analyzed attenuated total reflection (ATR) spectra of soil with and without Bio-MPs based on FTIR spectrometer, revealing the characteristic response in soil ATR spectra triggered by PBAT, and demonstrating ATR spectroscopy's potential for identifying soil contamination by Bio-MPs. This study aims to broaden and improve the utilization of FTIR spectroscopy for the purpose of monitoring soil GHG emissions and identifying soil contaminated by Bio-MPs, thereby offering significant insights into the influence of Bio-MPs on climate change.

Comparison of adsorption capacity of 4-Nonylphenol on conventional and biodegradable microplastics aged under natural water

This study investigated the adsorption of 4-Nonylphenol (4-NP) on aged microplastics (MPs) composed of polyethylene terephthalate (PET) and poly(butylene-adipate-co-terephthalate)/polylactic acid (PBAT/PLA). Morphological analysis revealed wear, wrinkles, and increased surface roughness in both aged MPs, with X-ray diffraction showing slight increases in crystallinity. Infrared spectroscopy showed an increase in the carbonyl index from 2.78 to 4.37 for PBAT/PLA and 0.51 to 2.32 for PET after aging. The natural water from the San Pedro River in Chile Atacama region (5.91 mS·cm-1 conductivity, 3.25 PSU salinity, 2955 mg·L-1 total dissolved solids, 435 mg·L-1 CaCO3 hardness) was used as the environmental medium and compared with a 0.01 mol·L-1 CaCl2 as a model solution. Kinetic modeling showed a decrease in 4-NP percentage removal from 90.0 % (2277 μg∙g-1 adsorption capacity) to 50.2 % (1268 μg∙g-1) for PET and from 86.8 % (2087 μg∙g-1) to 70.3 % (1955 μg∙g-1) for PBAT/PLA when comparing the model solution to natural water, with 30 and 84 h equilibrium times, respectively. Isotherm data showed that 4-NP/PET fits BET n-layer and Temkin models, while 4-NP-PBAT/PLA fits the Toth and Hill models The ionic composition of natural water induces cation attraction to polarized MPs surfaces, intensifying competition for adsorption sites. This involves ion and molecular cooperation, 4-NP reorientation, external diffusion effects, and surface oxidation variations, which are attributed to explaining the bilayer (PET) and monolayer (PBAT/PLA) formation. This work contributes to understanding MP pollution and the importance of considering the bioplastics life cycle, since their waste presents significant potential to resist external factors for transporting contaminants.

Microplastics influencing aquatic environment and human health: A review of source, determination, distribution, removal, degradation, management strategy and future perspective

Microplastics (MPs) are produced from various primary and secondary sources and pose multifaceted environmental problems. They are of non-biodegradable nature and may stay in aquatic environments for a long time period. The present review has covered novel aspects pertaining to MPs that were not covered in earlier studies. It has been observed that several methods are being employed for samples collection, extraction and identification of MPs and polymer types using various equipment, chemicals and instrumental techniques. Aquatic species mistakenly ingest MPs, considering them prey and through food-chain, and then suffer from various metabolic disorders. The consumption of seafood and fish may consequently cause health implications in humans. Certain plasticizers are added during manufacturing to provide colour, durability, flexibility, and strength to plastics, but they leach out during usage, storage, and transport, as well as after entering the bodies of aquatic species and human beings. The leached chemicals (bisphenol-A, triclosan, phthalates, etc.) act as endocrine disrupting chemicals (EDCs), which effect on homeostasis; thereby causing neurotoxicity, cytotoxicity, reproductive problems, adverse behaviour and autism. Negative influence of MPs on carbon sequestration potential of water bodies is also observed, however more studies are required to understand it with a detail mechanism under natural conditions. The wastewater treatment plants are found to remove a large amount of MPs, but in turn, also act as significant sources of their release in sludge and effluents. Further, it is covered that how advanced oxidation processes, thermal- and photo-oxidation, fungi, algae and microbes degrade the plastics and increase their numbers in the surrounding environment. The management strategy comprising recovery of energy and other valuable by-products from plastic wastes, recycling and regulatory framework; are also described in detail. The future perspectives can be of paramount importance to control MPs generation and their abundance in the aquatic and other types of environments. The studies in future need to focus on advanced filtration techniques, advanced oxidation processes, energy recovery from plastic wastes and influences of MPs on carbon sequestration in aquatic environment and human health.

Research advances of biodegradable microplastics in wastewater treatment plant: Current knowledge and future directions

Plastic and microplastic pollution in the environment has become a significant global concern. Biodegradable plastics (BPs), as environmentally friendly alternatives to conventional plastics, have also emerged as a crucial topic of global discussion. The successful application of BPs appears to offer a solution to the potential ecological risks posed by conventional plastics. However, BPs have negative impacts on the ecological environment and human health. BPs can gradually degrade into biodegradable microplastics (BMPs) in the environment. Wastewater treatment plants (WWTPs) have become an undeniable source and sink of microplastics. With the production and application of BPs, BMPs will inevitably enter WWTPs. This paper reviews the pollution status, degradation behavior of BMPs, and their potential impact on wastewater treatment performance. The focus is on the environmental behavior of BMPs in wastewater treatment systems. The influences of BMPs on microbial communities, sludge treatment, and disposal are thoroughly discussed. The results indicate that BMPs are more easily decomposed into micro/nanoplastics and release additives compared to conventional microplastics. The effects of BMPs on microbial communities and wastewater treatment depend on their characteristics. The numerous oxygen-containing functional groups on the surface of BMPs enable them to serve a dual purpose as transport media and potential sources of environmental pollutants. Finally, in light of existing knowledge gaps, suggestions and prospects for future research on BMPs are proposed.

Comparing environmental fate and ecotoxicity of conventional and biodegradable plastics: A critical review

Plastic pollution is a consequential problem worldwide, prompting the widespread use of biodegradable plastics (BPs). However, not all BPs are completely degradable under natural conditions, but instead produce biodegradable microplastics (BMPs), release chemical additives, and absorb micropollutants, thus causing toxicity to living organisms in similar manners to conventional plastics (CPs). The new problems caused by biodegradable plastics cannot be ignored and requires a thorough comparison of the differences between conventional and biodegradable plastics and microplastics. This review comprehensively compares their environmental fates, such as biodegradation and micropollutant sorption, and ecotoxicity in soil and water environments. The results showed that it is difficult to determine the natural conditions required for the complete biodegradation of BPs. Some chemical additives in BPs differ from those in CPs and may pose new threats to ecosystems. Because of functional group differences, most BMPs had higher micropollutant sorption capacities than conventional microplastics (CMPs). The ecotoxicity comparison showed that BMPs had similar or even greater adverse effects than CMPs. This review highlights several knowledge gaps in this new field and suggests directions for future studies.

Chemical toxicity of leachates from synthetic and natural-based spat collectors on the embryo-larval development of the pearl oyster, Pinctada margaritifera

In French Polynesia, the pearl farming industry relies entirely on collecting natural spat using a shade-mesh collector, which is reported to contribute to both plastic pollution and the release of toxic chemicals. With the aim of identifying more environment-friendly collectors, this study investigates the chemical toxicity of shade-mesh (SM) and alternative materials, including reusable plates (P), a newly developed biomaterial (BioM) and Coconut coir geotextile (Coco), on the embryo-larval development of Pinctada margaritifera. Embryos were exposed during 48 h to four concentrations (0, 0.1, 10 and 100 g L-1) of leachates produced from materials. Chemical screening of raw materials and leachates was performed to assess potential relationships with the toxicity observed on D-larvae development. Compared to the other tested materials, results demonstrated lower levels of chemical pollutants in BioM and no toxic effects of its leachates at 10 g L-1. No toxicity was observed at the lowest tested concentration (0.1 g L-1). These findings offer valuable insights for promoting safer spat collector alternatives such as BioM and contribute to the sustainable development of pearl farming.

Degradation of Polymer Materials in the Environment and Its Impact on the Health of Experimental Animals: A Review

The extensive use of polymeric materials has resulted in significant environmental pollution, prompting the need for a deeper understanding of their degradation processes and impacts. This review provides a comprehensive analysis of the degradation of polymeric materials in the environment and their impact on the health of experimental animals. It identifies common polymers, delineates their degradation pathways, and describes the resulting products under different environmental conditions. The review covers physical, chemical, and biological degradation mechanisms, highlighting the complex interplay of factors influencing these processes. Furthermore, it examines the health implications of degradation products, using experimental animals as proxies for assessing potential risks to human health. By synthesizing current research, the review focuses on studies related to small organisms (primarily rodents and invertebrates, supplemented by fish and mollusks) to explore the effects of polymer materials on living organisms and underscores the urgency of developing and implementing effective polymer waste management strategies. These strategies are crucial for mitigating the adverse environmental and health impacts of polymer degradation, thus promoting a more sustainable interaction between human activities and the natural environment.

Application of metal-organic frameworks for photocatalytic degradation of microplastics: Design, challenges, and scope

Microplastics (MPs), plastic particles smaller than 5 mm, are pervasive pollutants challenging wastewater treatment due to their size and hydrophobicity. They infiltrate freshwater, marine, and soil environments, posing ecological threats. In marine settings, MPs ingested by organisms cause cytokine release, cellular and DNA damage, and inflammation. As MPs enter the food chain and disrupt biological processes, their degradation is crucial. While biodegradation, pyrolysis, and chemical methods have been extensively studied, the use of metal-organic frameworks (MOFs) for MP pollution mitigation is underexplored. In this study, we explored the photocatalytic degradation mechanisms of MPs by MOFs in aquatic environments. We analyzed the hydrolysis, oxidation, and adsorption processes, while focusing on the environmentally friendly and cost-effective photocatalytic approach. Additionally, we analyzed the literature on MP decomposition for various types of MOFs, providing a detailed understanding of the degradation mechanisms specific to each MOF. Furthermore, we evaluated the degradation efficiencies of different MOFs and discussed the challenges and limitations in their application. Our study highlights the need for an integrated approach that involves the application of MOFs while considering environmental factors and safety concerns to develop effective MP degradation models. This review provides a framework for developing reliable photocatalytic materials with high MP removal and degradation efficiencies, thereby promoting the use of MOFs for marine plastic pollution mitigation.

Early-life exposure to five biodegradable plastics impairs eye development and visually-mediated behavior through disturbing hypothalamus-pituitary-thyroid (HPT) axis in zebrafish larvae

Biodegradable plastics have been commonly developed and applied as an alternative to traditional plastics, which cause environmental plastic pollution. However, biodegradable plastics still present limitations such as stringent degradation conditions and slow degradation rate, and may cause harm to the environment and organisms. Consequently, in this study, zebrafish was used to evaluate the effects of five biodegradable microplastics (MPs), polyglycolic acid (PGA), polylactic acid (PLA), polybutylene succinate (PBS), polyhydroxyalkanoate (PHA) and polybutylene adipate terephthalate (PBAT) exposure on the early development, retina morphology, visually-mediated behavior, and thyroid signaling at concentrations of 1 mg/L and 100 mg/L. The results indicated that all MPs induced decreased survival rate, reduced body length, smaller eyes, and smaller heads, affecting the early development of zebrafish larvae. Moreover, the thickness of retinal layers, including inner plexiform layer (IPL), outer nuclear layer (ONL), and retinal ganglion layer (RGL) was decreased, and the expression of key genes related to eye and retinal development was abnormally altered after all MPs exposure. Exposure to PBS and PBAT led to abnormal visually-mediated behavior, indicating likely affected the visual function. All MPs could also cause thyroid system disorders, among which alterations in the thyroid hormone receptors (TRs) genes could affect the retinal development of zebrafish larvae. In summary, biodegradable MPs exhibited eye developmental toxicity and likely impaired the visual function in zebrafish larvae. This provided new evidence for revealing the effects of biodegradable plastics on aquatic organism development and environmental risks to aquatic ecosystems.

How micro-/nano-plastics influence the horizontal transfer of antibiotic resistance genes - A review

Plastic debris such as microplastics (MPs) and nanoplastics (NPTs), along with antibiotic resistance genes (ARGs), are pervasive in the environment and are recognized as significant global health and ecological concerns. Micro-/nano-plastics (MNPs) have been demonstrated to favor the spread of ARGs by enhancing the frequency of horizontal gene transfer (HGT) through various pathways. This paper comprehensively and systematically reviews the current study with focus on the influence of plastics on the HGT of ARGs. The critical role of MNPs in the HGT of ARGs has been well illustrated in sewage sludge, livestock farms, constructed wetlands and landfill leachate. A summary of the performed HGT assay and the underlying mechanism of plastic-mediated transfer of ARGs is presented in the paper. MNPs could facilitate or inhibit HGT of ARGs, and their effects depend on the type, size, and concentration. This review provides a comprehensive insight into the effects of MNPs on the HGT of ARGs, and offers suggestions for further study. Further research should attempt to develop a standard HGT assay and focus on investigating the impact of different plastics, including the oligomers they released, under real environmental conditions on the HGT of ARGs.

Stressful Effects of Individual and Combined Exposure to Low-Concentration Polylactic Acid Microplastics and Chromium on Marine Medaka Larvae (Oryzias melastigma)

Microplastics and heavy metal pollution frequently co-occur in the marine environment, raising concerns about their potentially harmful impacts on marine fish. This study undertook a comprehensive evaluation of the individual and combined stress effects of polylactide microplastics (PLA-MPs) and chromium (Cr) on marine medaka larvae. Following a 14-day exposure to PLA-MPs (100 μg/L) and Cr (50 μg/L), both individually and in combination, significant increases in heart rate and body length were observed. Notably, the combined exposure to PLA-MPs and Cr caused marked histopathological alterations, including shedding, atrophy, and lysis of the intestinal tissues. Furthermore, both individual and combined exposure induced oxidative stress in fish larvae, leading to changes in various enzyme activity indices. Individual exposure to either PLA-MPs or Cr led to anxious behavior in the larvae, whereas combined exposure not only caused anxious behavior but also altered swimming patterns. These findings suggest that combined exposure to PLA-MPs and Cr can exacerbate the toxic effects on marine medaka larvae.

Transitioning to Microplastic-Free Seed Coatings: Challenges and Solutions

This review addresses the issue of replacing manufactured microplastics in seed coatings used in agriculture. Firstly, it focuses on the policy and regulatory actions taken on microplastics at a global level. There is no consensus within the scientific community on the definition of a microplastic and, more generally, on the classification of plastic debris. Nevertheless, several decision schemes have been proposed in an attempt to define the notion of microplastics. The different criteria relevant to this definition, such as the size, physical state, chemical structure, origin, and persistence of microplastics, are discussed, with a comparison being made between the REACH regulation and the scientific literature. Seed production and processing are also discussed, with the functions of seed coatings being explained in order to gain a better understanding of the properties to be considered in a substitution strategy for currently used microplastics. The main challenges are multiple; substitutes must provide the same performance as microplastics: (i) improving the adherence of the treatment to the seed, (ii) distributing the treatment more evenly over the seed, (iii) reducing the amount of dust-off when handling treated seed, and (iv) improving the seed flowability, which is particularly important during the sowing stage, all while preserving the physiological properties of the seed. Substitute polymers are proposed according to the desired performance and functional properties: two main chemical families of biopolymers were identified in the literature: polysaccharides and proteins. Among them, 13 and 6 polymers, respectively, complied with REACH regulation, demonstrating adhesion, dust reduction performances, and preservation of seed physiological quality in particular. This work aims to guide future studies on microplastic substitution in seed coatings, and to highlight research needs in this area. It is based on an analysis and discussion of the literature, identifying and listing potential substitutes.

Exploring the Future of Polyhydroxyalkanoate Composites with Organic Fillers: A Review of Challenges and Opportunities

Biopolymers from renewable materials are promising alternatives to the traditional petroleum-based plastics used today, although they face limitations in terms of performance and processability. Natural fillers have been identified as a strategic route to create sustainable composites, and natural fillers in the form of waste by-products have received particular attention. Consequently, the primary focus of this article is to offer a broad overview of recent breakthroughs in environmentally friendly Polhydroxyalkanoate (PHA) polymers and their composites. PHAs are aliphatic polyesters obtained by bacterial fermentation of sugars and fatty acids and are considered to play a key role in addressing sustainability challenges to replace traditional plastics in various industrial sectors. Moreover, the article examines the potential of biodegradable polymers and polymer composites, with a specific emphasis on natural composite materials, current trends, and future market prospects. Increased environmental concerns are driving discussions on the importance of integrating biodegradable materials with natural fillers in our daily use, emphasizing the need for clear frameworks and economic incentives to support the use of these materials. Finally, it highlights the indispensable need for ongoing research and development efforts to address environmental challenges in the polymer sector, reflecting a growing interest in sustainable materials across all industries.

Generation of synthetic FTIR spectra to facilitate chemical identification of microplastics

In a context where learning databases of microplastic FTIR spectra are often incomplete, the objective of our work was to test whether a synthetic data generation method could be relevant to fill the gaps. To this end, synthetic spectra were generated to create new databases. The effectiveness of machine learning from these databases was then tested and compared with previous results. The results showed that the creation of synthetic learning databases could avoid, to a certain extent, the need for learning databases of environmental microplastics FTIR spectra. However, some limitations were encountered, for example, when two different chemical classes had very similar reference spectra or when the intensities of the bands associated with fouling became too intense. The FTIR study of the ageing and fouling of microplastics in the natural environment is one of the identified ways that could further improve this approach.

Tracking the micro- and nanoplastics in the terrestrial-freshwater food webs. Bivalves as sentinel species

Micro- (MPs) and nanoplastics (NPs) are currently ubiquitous in the ecosystems, and freshwater biota is still insufficiently studied to understand the global fate, transport paths, and consequences of their presence. Thus, in this study, we investigated the role of bivalves and a trophic transfer of MPs and NPs in an experimental food chain. The food chain consisted of terrestrial non-selective detritivore Dendrobaena (Eisenia) sp., freshwater benthic filter feeder Unio tumidus, and freshwater benthic detritivore-collectors Asellus aquaticus or Gammarus sp. Animals were exposed to different fluorescently labeled micro- and nanoplastics (PMMA 20 μm, nanoPS 15-18 nm, and 100 nm, PS 1 μm and 20 μm, PE from cosmetics) as well as to the faeces of animals exposed to plastics to assess their influence on the environmental transportation, availability to biota, and bioaccumulation of supplied particles. Damaged and intact fluorescent particles were observed in the faeces of terrestrial detritivores and in the droppings of aquatic filter feeders, respectively. They were also present in the guts of bivalves and of crustaceans which were fed with bivalve droppings. Bivalves (Unio tumidus, and additionally Unio pictorum, and Sphaerium corneum) produced droppings containing micro- and nanoparticles filtered from suspension and deposited them onto the tank bottom, making them available for broader feeding guilds of animals (e.g. collectors, like crustaceans). Finally, the natural ageing of PS and its morphological changes, leakage of the fluorescent labelling, and agglomeration of particles were demonstrated. That supports our hypothesis of the crucial role of the characterization of physical and chemical materials in adequately understanding the mechanisms of their interaction with biota. Microscopical methods (confocal, fluorescent, scanning electron) and Raman and FT-IR spectroscopy were used to track the particles' passage in a food web and monitor structural changes of the MPs' and NPs' surface.

A review on fate and ecotoxicity of biodegradable microplastics in aquatic system: Are biodegradable plastics truly safe for the environment?

Plastic products are extensively used worldwide, but inadequate management of plastic waste results in significant plastic pollution. Biodegradable plastic (BPs) offers an alternative to traditional plastics, however, not all BPs can fully degrade under natural conditions. Instead, they may deteriorate into biodegradable microplastic (BMPs) at a faster rate than conventional plastic, thereby posing an additional hazard to aquatic environments. This study provides a comprehensive overview of the fate of BPs in aquatic systems and their eco-toxicological effects on aquatic organisms such as algae, invertebrates, and fish. The findings highlight that BMPs have comparable or heightened effects compared to conventional microplastics (MPs) which physiochemical characteristic of the polymer itself or by the chemical leached from the polymeric matrix can affect aquatic organisms. While BPs is not a flawless solution to address plastic pollution, future research should prioritize investigating their production, environmental behavior, ecological impact, and whether BMPs inflict greater harm than conventional MPs.

Interactions of humic acid with pristine poly (lactic acid) microplastics in aqueous solution

Microplastics and natural organic matter are present in the aquatic environment and their reciprocal interaction plays important roles in the transport and behavior of nutrients and contaminants. Nevertheless, we lack mechanistic understanding on these interactions, especially in the case of biodegradable plastics. Here we investigate the adsorption of a commercial humic acid onto poly (lactic acid) (PLA) microplastics in aqueous solution. While the pseudo-second order kinetic model provided a more accurate representation of the adsorption kinetics, the Elovich model also produced a good fit, suggesting that chemisorption may be the rate-limiting step. The equilibrium data was better fit by the Langmuir model, that provided a maximum adsorption capacity of 0.118 ± 0.006 mg·g-1. The obtained values for the separation factor (RL) and free energy (E) suggest that adsorption of humic acid onto PLA is controlled by physisorption. We studied the effects of pH, ionic strength, and PLA concentration on the adsorption of humic acid onto PLA and demonstrated that electrostatic interactions and aggregation are important. The humic acid was characterized by Fourier-transform infrared (FTIR) spectroscopy, excitation-emission matrix (EEM) fluorescence spectroscopy, and parallel factor analysis (PARAFAC), before and after interacting with PLA. This set of analyses demonstrated that PLA caused alterations in the molecular structure of humic acid, primarily attributed to modifications in hydrogen bonding and hydrophobic interactions. Therefore, we hypothesize that the carboxylic groups of humic acid formed dimers in contact with PLA. This study provides new insights into the interactions between organic matter and a biodegradable microplastic in aqueous systems.

Synthesis and commercialization of bioplastics: Organic waste as a sustainable feedstock

Substituting synthetic plastics with bioplastics, primarily due to their inherent biodegradable properties, represents a highly effective strategy to address the current global issue of plastic waste accumulation in the environment. Advances in bioplastic research have led to the development of materials with improved properties, enabling their use in a wide range of applications in major commercial sectors. Bioplastics are derived from various natural sources such as plants, animals, and microorganisms. Polyhydroxyalkanoate (PHA), a biopolymer synthesized by bacteria through microbial fermentation, exhibits physicochemical and mechanical characteristics comparable to those of synthetic plastics. In response to the growing demand for these environmentally friendly plastics, researchers are actively investigating various cleaner production methods, including modification or derivatization of existing molecules for enhanced properties and new-generation applications to expand their market share in the coming decades. By 2026, the commercial manufacturing capacity of bioplastics is projected to reach 7.6 million tonnes, with Europe currently holding a significant market share of 43.5 %. Bioplastics are predominantly utilized in the packaging industry, indicating a strong focus of their application in the sector. With the anticipated rise in bioplastic waste volume over the next few decades, it is crucial to comprehend their fate in various environments to evaluate the overall environmental impact. Ensuring their complete biodegradation involves optimizing waste management strategies and appropriate disposal within these facilities. Future research efforts should prioritize exploration of their end-of-life management and toxicity assessment of degradation products. These efforts are crucial to ensure the economic viability and environmental sustainability of bioplastics as alternatives to synthetic plastics.

A review of the occurrence and degradation of biodegradable microplastics in soil environments

The use of plastics for manufacturing of products and packaging has become ubiquitous. This is because plastics are cheap, pliable, and durable. However, these characteristics of plastics have also led to their disposal in landfill, where they persist. To overcome the environmental challenge posed by conventional plastics (CPs), biodegradable plastics (BDPs) are increasingly being used. However, BDPs form residual microplastics (MPs) at a rate that far exceeds that of CPs, and MPs have negative impacts on the soil environment. This review aimed to evaluate whether the move away from CPs to BDPs is having an overall positive impact on the environment considering the formation of MPs. Topics focused on in this review include the degradation of BDPs in the soil environment and the impacts of MPs originating from BDPs on soil physical and chemical properties, microbial communities, animals, and plants. The information collated in this review can provide scientific guidance for sustainable development of the BDPs industry.

Investigations into the characterization, degradation, and applications of biodegradable polymers by mass spectrometry

Biodegradable polymers have been getting more and more attention because of their contribution to the plastic pollution environmental issues and to move towards a circular economy. Nevertheless, biodegradable materials still exhibit various disadvantages restraining a widespread use in the market. Therefore, additional research efforts are required to improve their performance. Mass spectrometry (MS) affords a relevant contribution to optimize biodegradable polymer synthesis, to confirm macromolecular structures, to examine along the time the progress of degradation processes and highlight advantages and drawbacks in the extensive applications. This review aims to provide an overview of the MS investigations carried out to support the synthesis of biodegradable polymers, with helpful information on undesirable products or polymerization mechanism, to understand deterioration pathways by the structure of degradation products and to follow drug release and pharmacokinetic. Additionally, it summarizes MS studies addressed on environmental and health issues related to the extensive use of plastic materials, that is, potential migration of additives or microplastics identification and quantification. The paper is focused on the most significant studies relating to synthetic and microbial biodegradable polymers published in the last 15 years, not including agro-polymers such as proteins and polysaccharides.

Are biodegradable mulch films a sustainable solution to microplastic mulch film pollution? A biogeochemical perspective

Mulch film residue contributes significantly to global plastic pollution, and consequently biodegradable mulch films (BDMs) are being adopted as a solution. BDMs decompose relatively quickly, but their complete biodegradation requires suitable conditions that are difficult to achieve in nature, causing biodegradable microplastics (bio-MPs) to be more likely to accumulate in soil than traditional microplastics (MPs). If BDMs are to be considered as a sustainable solution, long-term and in-depth studies to investigate the impact of bio-MPs on the biogeochemical processes are vital to agroecosystems operation and ecosystem services supply. Although bio-MP-derived carbon can potentially convert into biomass during decomposition, its contribution to soil carbon stocks is insignificant. Instead, given their biodegradability, bio-MPs can result in greater alterations of soil biodiversity and community composition. Their high carbon-nitrogen ratios may also significantly regulate various processes involved in the natural decomposition and transformation of soil organic matter, including the reduction of nutrient availability and increase in greenhouse gas emissions. Soil ecosystems are complex organic entities interconnected by disturbance-feedback mechanisms. Given the prevailing knowledge gaps regarding the impact of bio-MPs on soil biogeochemical cycles and ecosystem balance, this study emphasized the safety and sustainability assessment of bio-MPs and the prevailing comprehensive challenges.

Understanding the Impact of Biodegradable Microplastics on Living Organisms Entering the Food Chain: A Review

Microplastics (MPs) pollution has emerged as one of the world's most serious environmental issues, with harmful consequences for ecosystems and human health. One proposed solution to their accumulation in the environment is the replacement of nondegradable plastics with biodegradable ones. However, due to the lack of true biodegradability in some ecosystems, they also give rise to biodegradable microplastics (BioMPs) that negatively impact different ecosystems and living organisms. This review summarizes the current literature on the impact of BioMPs on some organisms-higher plants and fish-relevant to the food chain. Concerning the higher plants, the adverse effects of BioMPs on seed germination, plant biomass growth, penetration of nutrients through roots, oxidative stress, and changes in soil properties, all leading to reduced agricultural yield, have been critically discussed. Concerning fish, it emerged that BioMPs are more likely to be ingested than nonbiodegradable ones and accumulate in the animal's body, leading to impaired skeletal development, oxidative stress, and behavioral changes. Therefore, based on the reviewed pioneering literature, biodegradable plastics seem to be a new threat to environmental health rather than an effective solution to counteract MP pollution, even if serious knowledge gaps in this field highlight the need for additional rigorous investigations to understand the potential risks associated to BioMPs.

Insights into Anthropogenic Micro- and Nanoplastic Accumulation in Drinking Water Sources and Their Potential Effects on Human Health

Anthropogenic microplastics (MPs) and nanoplastics (NPs) are ubiquitous pollutants found in aquatic, food, soil and air environments. Recently, drinking water for human consumption has been considered a significant pathway for ingestion of such plastic pollutants. Most of the analytical methods developed for detection and identification of MPs have been established for particles with sizes > 10 μm, but new analytical approaches are required to identify NPs below 1 μm. This review aims to evaluate the most recent information on the release of MPs and NPs in water sources intended for human consumption, specifically tap water and commercial bottled water. The potential effects on human health of dermal exposure, inhalation, and ingestion of these particles were examined. Emerging technologies used to remove MPs and/or NPs from drinking water sources and their advantages and limitations were also assessed. The main findings showed that the MPs with sizes > 10 μm were completely removed from drinking water treatment plants (DWTPs). The smallest NP identified using pyrolysis-gas chromatography-mass spectrometry (Pyr-GC/MS) had a diameter of 58 nm. Contamination with MPs/NPs can occur during the distribution of tap water to consumers, as well as when opening and closing screw caps of bottled water or when using recycled plastic or glass bottles for drinking water. In conclusion, this comprehensive study emphasizes the importance of a unified approach to detect MPs and NPs in drinking water, as well as raising the awareness of regulators, policymakers and the public about the impact of these pollutants, which pose a human health risk.

Bio-straw or not? Determinants of consumption intention under the plastic straw ban

A new plastic ban has banned the use of single-use non-degradable plastic drinking straws in China's food and beverage industry by the end of 2020. However, this has caused widespread discussion and complaints on social media. What are consumers' reactions and what factors influence consumers to choose bio-straws (substitutes for plastic straws) are unclear. Therefore, this research collected 4367 effective comments (177,832 words in total) on "bio-straws" from social media and extracted keywords based on grounded theory to generate questionnaires. Structural equation modeling was used to analyze the consumption intention and influencing factors of 348 consumers regarding the ban. The results indicate the following: (1) consumer opinion on straws can be summarized into five main categories, namely, consumers' user experience, consumer subjectivity, policy awareness, policy acceptance, and consumption intention; (2) consumer subjectivity, policy awareness, and policy acceptance directly affect consumption intention significantly, while user experience affects consumption intention indirectly; and (3) user experience and consumer subjectivity play significant roles in mediating these relationships. From the perspective of consumers, this study provides an important basis for policymakers to formulate single-use plastic alternative policies in the future.

Impact of buried debris from agricultural biodegradable plastic mulches on two horticultural crop plants: Tomato and lettuce

Biodegradable mulches (BDM) are increasingly valued and used for substituting non-biodegradable plastic mulches polluting agricultural soils. They are tilled into soil, where they fragment and release compounds throughout their biodegradation. The consequences of BDM use on the plant-soil environment have been partially studied with pristine and with artificially-weathered BDM fragments. However, to guarantee safety use of BDM, studies on the BDM debris effects are required. For this, to determine potential effects of the field-weathering BDM on plants, a mesocosm experiment was performed by sowing seeds from two major plant species commonly cultivated with BDM, tomato (Lycopersicon esculentum) and lettuce (Lactuca sativa), in plant pots containing pristine and field-weathered pieces from seven different BDM formulations, one paper mulch, a polyethylene (PE) mulch, and no-mulch control pots. Germination of both plant species was unaffected by any of the mulch treatments; however, PHB (polyhydroxybutyrate)-based BDM fragments severely inhibited tomato and lettuce plant growth, 90 and 95 %, respectively. Moreover, all pristine and field-weathered BDM significantly delayed lettuce plant development. Tomato plant growth progressed better, but growth retardation was also evidenced with most field-weathered BDM treatments. Overall, field-weathered fragments caused stronger effects on plants than the pristine unused ones. No effects were found for PE mulch, either pristine or field-weathered. The obtained results highlight that BDM debris may alter plant development depending on their nature and on their weathering, rather than on their physical presence, and evidence the need to conduct further experiments on the impact of field-weathered BDM on the plant-soil environment.

A starch-based, crosslinked blend film with seawater-specific dissolution characteristics

Existing biodegradable plastics may not be ideal replacements of petroleum-based single-use plastics owing to their slow biodegradation in seawater. To address this issue, a starch-based blend film with different disintegration/dissolution speeds in freshwater and seawater was prepared. Poly(acrylic acid) segments were grafted onto starch; a clear and homogenous film was prepared by blending the grafted starch with poly(vinyl pyrrolidone) (PVP) by solution casting. After drying, the grafted starch was crosslinked with PVP by hydrogen bonds, owing to which the water stability of the film is higher than that of unmodified starch films in fresh water. In seawater, the film dissolves quickly as a result of disruption of the hydrogen bond crosslinks. This technique balances degradability in marine environment and water resistance in everyday environment, provides an alternative route to mitigate marine plastic pollution and could be potentially useful for single-use applications in different fields such as packaging, healthcare, and agriculture.

The Raman spectroscopy and SEM/EDS investigation of the primary sources of microplastics from cosmetics available in Poland

The increasing amount of marine microplastics and nanoplastics is due to primary (P-MPs) and secondary sources (S-MPs). Among small P-MPs and fibres from textiles, nurdles or industrial dust, the microbeads from cosmetics (peelings, scrubs) are dominant. The polyethylene and polypropylene debris, already <5 mm, enlarge Plastisphere and have a complex influence on environmental processes. Fortunately, the situation has changed with the limitation of synthetic materials in scrubs in recent years. This paper summarizes the six years of studies (2015-2021) on microplastics in cosmetics available on the Polish market. It focuses on those still available and presents the potential of Raman spectroscopy for the efficient qualitative and quantitative characterization of those materials. Finally, surface morphology's vital role in microplastics' general behaviour is underlined. The SEM/EDX and numerical modelling enables a more detailed description of particles.

Dark side of a bio-based and biodegradable plastic? Assessment of pathogenic microbes associated with poly(butylene succinate-co-adipate) under ambient and future climates using next-generation sequencing

Bio-based and biodegradable plastic mulching films have been proposed to replace the non-biodegradable plastic mulch films to solve plastic pollution problems in agricultural soils. However, the impact of bio-based and biodegradable plastics on plant and human health remains largely unexplored. Here, we aimed to assess the risk under field conditions of a bio-based and biodegradable poly(butylene succinate-co-adipate; PBSA), a widely used mulching film as carrier of potential pathogenic microorganisms (bacteria and fungi) at ambient and future climate conditions. Overall, we affiliated 64 fungal and 11 bacterial operational taxonomic units (OTUs) as pathogens by using Next-Generation Sequencing approach. Our results revealed that PBSA hosted at least 53 plant pathogens, of which 51 were classified as fungi, while the other two were bacteria. Most fungal plant pathogens were able to withstand the anticipated future climate changes. We detected 13 fungal and eight bacterial OTUs, which were classified as opportunistic human pathogens. Only one bacterial OTU (Enterococcus faecium) was assigned to a human pathogen. While future climate conditions only significantly impacted on the presence and frequency of detection of few pathogens, incubation time was found to significantly impacted on nine pathogens. This result demonstrates the temporal dynamics of pathogens associated with PBSA. The threats to plant and human health were discussed. We emphasize that the risks to human health are relatively low because we mainly found opportunistic pathogens associated with PBSA and the amount are comparable to the plant debris. However, the risks to plant health may be considered as moderate because many plant pathogens were discovered and/or enriched in PBSA. Furthermore, in soil environments, the pathogenic risk of plastic is highly depending on the surrounding soil pathobiome where plastic is being decomposed.

Identification and Quantification of Micro-Bioplastics in Environmental Samples by Pyrolysis-Gas Chromatography-Mass Spectrometry

Bioplastics are materials that are biobased and/or biodegradable, but not necessarily both. Concerns about environmental plastic pollution are constantly growing with increasing demand for substituting fossil-based plastics with those made using renewable resource feedstocks. For many conventional bioplastics to completely decompose/degrade, they require specific environmental conditions that are rarely met in natural ecosystems, leading to rapid formation of micro-bioplastics. As global bioplastic production and consumption/use continue to increase, there is growing concern regarding the potential for environmental pollution from micro-bioplastics. However, the actual extent of their environmental occurrence and potential impacts remains unclear, and there is insufficient mass concentration-based quantitative data due to the lack of quantitative analytical methods. This study developed and validated an analytical method coupling pressurized liquid extraction and pyrolysis-gas chromatography-mass spectrometry combined with thermochemolysis to simultaneously identify and quantify five targeted micro-bioplastics (i.e., polylactic acid (PLA), polyhydroxyalkanoate, polybutylene succinate, polycaprolactone, and polybutylene adipate terephthalate (PBAT)) in environmental samples on a polymer-specific mass-based concentration. The recovery of spiked micro-bioplastics in environmental samples (biosolids) ranged from 74 to 116%. The limits of quantification for the target micro-bioplastics were between 0.02 and 0.05 mg/g. PLA and PBAT were commonly detected in wastewater, biosolids, and sediment samples at concentrations between 0.07 and 0.18 mg/g. The presented analytical method enables the accurate identification, quantification, and monitoring of micro-bioplastics in environmental samples. This study quantified five micro-bioplastic types in complex environmental samples for the first time, filling in gaps in our knowledge about bioplastic pollution and providing a useful methodology and important reference data for future research.

Merging Plastics, Microbes, and Enzymes: Highlights from an International Workshop

In the Anthropocene, plastic pollution is a worldwide concern that must be tackled from different viewpoints, bringing together different areas of science. Microbial transformation of polymers is a broad-spectrum research topic that has become a keystone in the circular economy of fossil-based and biobased plastics. To have an open discussion about these themes, experts in the synthesis of polymers and biodegradation of lignocellulose and plastics convened within the framework of The Transnational Network for Research and Innovation in Microbial Biodiversity, Enzymes Technology and Polymer Science (MENZYPOL-NET), which was recently created by early-stage scientists from Colombia and Germany. In this context, the international workshop "Microbial Synthesis and Degradation of Polymers: Toward a Sustainable Bioeconomy" was held on 27 September 2021 via Zoom. The workshop was divided into two sections, and questions were raised for discussion with panelists and expert guests. Several key points and relevant perspectives were delivered, mainly related to (i) the microbial evolution driven by plastic pollution; (ii) the relevance of and interplay between polymer structure/composition, enzymatic mechanisms, and assessment methods in plastic biodegradation; (iii) the recycling and valorization of plastic waste; (iv) engineered plastic-degrading enzymes; (v) the impact of (micro)plastics on environmental microbiomes; (vi) the isolation of plastic-degrading (PD) microbes and design of PD microbial consortia; and (vii) the synthesis and applications of biobased plastics. Finally, research priorities from these key points were identified within the microbial, enzyme, and polymer sciences.

Millions of microplastics released from a biodegradable polymer during biodegradation/enzymatic hydrolysis

In this article, we show that enzymatic hydrolysis of a biodegradable polyester (poly(ε-caprolactone)) by Amano Lipase PS in an aqueous (buffer) environment yielded rapidly an excessive number of microplastic particles; merely 0.1 g of poly(ε-caprolactone) film was demonstrated to yield millions of particles. There were also indications of non-enzymatic hydrolysis at the same conditions, but this did not yield any particles within the time frame of the experiment (up to 6 days). Microplastic particles formed had irregular shapes with an average size of around 10 µm, with only a few reaching 60 µm. The formation of microplastic particles resulted from the uneven hydrolysis/erosion rate across the polymer film surface, which led to a rough and undulating surface with ridge, branch, and rod-shaped micro-protruding structures. The consequent detachment and fragmentation of these micro-sized protruding structures resulted in the release of microplastics to the surroundings. Together with microplastics, hydrolysis products such as acidic monomers and oligomers were also released during the enzymatic hydrolysis process, causing a pH decrease in the surrounding liquid. The results suggest that the risk of microplastic pollution from biodegradable plastics is notable despite their biodegradation. Special attention needs to be paid when using and disposing of biodegradable plastics, considering the enormous impact of the paradigm shift towards more biodegradable products on the environment.