An electrospun fiber-covered stent with programmable dual drug release for endothelialization acceleration and lumen stenosis prevention

Hydrogel coating containing heparin and cyclodextrin/paclitaxel inclusion complex for retrievable vena cava filter towards high biocompatibility and easy removal

Aiming to improve the retrieval rate of retrievable vena cava filters (RVCF) and extend its dwelling time in vivo, a novel hydrogel coating loaded with 10 mg/mL heparin and 30 mg/mL cyclodextrin/paclitaxel (PTX) inclusion complex (IC) was prepared. The drug-release behavior in the phosphate buffer solution demonstrated both heparin and PTX could be sustainably released over approximately two weeks. Furthermore, it was shown that the hydrogel-coated RVCF (HRVCF) with 10 mg/mL heparin and 30 mg/mL PTX IC effectively extended the blood clotting time to above the detection limit and inhibited EA.hy926 and CCC-SMC-1 cells' proliferation in vitro compared to the commercially available bare RVCF. Both the HRVCF and the bare RVCF were implanted into the vena cava of sheep and retrieved at at 2nd and 4th week after implantation, revealing that the HRVCF had a significantly higher retrieval rate of 67 % than the bare RVCF (0 %) at 4th week. Comprehensive analyses, including histological, immunohistological, and immunofluorescent assessments of the explanted veins demonstrated the HRVCF exhibited anti-hyperplasia and anticoagulation properties in vivo, attributable to the hydrogel coating, thereby improving the retrieval rate in sheep. Consequently, the as-prepared HRVCF shows promising potential for clinical application to enhance the retrieval rates of RVCFs.

Puerarin-Loaded Electrospun Patches with Anti-Inflammatory and Pro-Collagen Synthesis Properties for Pelvic Floor Reconstruction

Pelvic organ prolapse (POP) is one of the most common pelvic floor dysfunction disorders worldwide. The weakening of pelvic connective tissues initiated by excessive collagen degradation is a leading cause of POP. However, the patches currently used in the clinic trigger an unfavorable inflammatory response, which often leads to implantation failure and the inability to simultaneously reverse progressive collagen degradation. Therefore, to overcome the present challenges, a new strategy is applied by introducing puerarin (Pue) into poly(l-lactic acid) (PLLA) using electrospinning technology. PLLA improves the mechanical properties of the patch, while Pue offers intrinsic anti-inflammatory and pro-collagen synthesis effects. The results show that Pue is released from PLLA@Pue in a sustained manner for more than 20 days, with a total release rate exceeding 80%. The PLLA@Pue electrospun patches also show good biocompatibility and low cytotoxicity. The excellent anti-inflammatory and pro-collagen synthesis properties of the PLLA@Pue patch are demonstrated both in vitro in H2O2-stimulated mouse fibroblasts and in vivo in rat abdominal wall muscle defects. Therefore, it is believed that this multifunctional electrospun patch integrating anti-inflammatory and pro-collagen synthesis properties can overcome the limitations of traditional patches and has great prospects for efficient pelvic floor reconstruction.

Design and Fabrication of Environmentally Responsive Nanoparticles for the Diagnosis and Treatment of Atherosclerosis

Cardiovascular disease poses a significant threat to human health in today's society. A major contributor to cardiovascular disease is atherosclerosis (AS). The development of plaque in the affected areas involves a complex pathological environment, and the disease progresses rapidly. Nanotechnology, combined with emerging diagnostic and treatment methods, offers the potential for the management of this condition. This paper presents the latest advancements in environment-intelligent responsive controlled-release nanoparticles designed specifically for the pathological environment of AS, which includes characteristics such as low pH, high reactive oxygen species levels, high shear stress, and multienzymes. Additionally, the paper summarizes the applications and features of nanotechnology in interventional therapy for AS, including percutaneous transluminal coronary angioplasty and drug-eluting stents. Furthermore, the application of nanotechnology in the diagnosis of AS shows promising real-time, accurate, and continuous effects. Lastly, the paper explores the future prospects of nanotechnology, highlighting the tremendous potential in the diagnosis and treatment of atherosclerotic diseases, especially with the ongoing development in nano gas, quantum dots, and Metal-Organic Frameworks materials.

Endothelialization of PTFE-covered stents for aneurysms and arteriovenous fistulas created in canine carotid arteries

To investigate the endothelialization of covered and bare stents deployed in the canine carotid arteries and subclavian arteries for treating experimental aneurysms and arteriovenous fistulas, twenty aneurysms were created in 10 dogs, and 20 fistulas in another 10 dogs. The Willis balloon-expandable covered stent and a self-expandable covered stent were used to treat these lesions, and a self-expandable bare stent was deployed in the subclavian artery for comparison. Followed up for up to 12 months, the gross observation, pathological staining, and scanning electronic microscopic data were analyzed. Two weeks after creation of animal model, thirty self-expandable covered stents and ten balloon-expandable covered stents were deployed. Fifteen bare stents were deployed within the left subclavian arteries. Twenty days after stenting, the aneurysm significantly shrank. At 6 months, the thrombi within the aneurysm cavity were organized. Three to 12 months later, most covered and bare stents were covered by a thin transparent or white layer of endothelial intima. Layers of intima or pseudomembrane were formed on the stent 20-40 days after stent deployment. Over three months, the pseudomembrane became organized, thinner, and merged into the vascular wall. Under scanning electronic microscopy, the surface of covered and bare stents had only deposition of collagen fibers and rare endothelial cells 20-40 days after stenting. From three to ten months, the endothelial cells on the internal surface of stent became mature, with spindle, stripe-like or quasi round morphology along the blood flow direction. Over time, the endothelial cells became mature. In conclusion, three months after deployment in canines' arteries, the self-expandable bare and covered stents have mostly been covered by endothelial cells which become maturer over time, whereas the balloon-expandable covered stents do not have complete coverage of endothelial cells at three months, especially for protruding stent struts and areas. Over time, the endothelialization will become mature.

Resorbable Membranes for Guided Bone Regeneration: Critical Features, Potentials, and Limitations

Lack of horizontal and vertical bone at the site of an implant can lead to significant clinical problems that need to be addressed before implant treatment can take place. Guided bone regeneration (GBR) is a commonly used surgical procedure that employs a barrier membrane to encourage the growth of new bone tissue in areas where bone has been lost due to injury or disease. It is a promising approach to achieve desired repair in bone tissue and is widely accepted and used in approximately 40% of patients with bone defects. In this Review, we provide a comprehensive examination of recent advances in resorbable membranes for GBR including natural materials such as chitosan, collagen, silk fibroin, along with synthetic materials such as polyglycolic acid (PGA), polycaprolactone (PCL), polyethylene glycol (PEG), and their copolymers. In addition, the properties of these materials including foreign body reaction, mechanical stability, antibacterial property, and growth factor delivery performance will be compared and discussed. Finally, future directions for resorbable membrane development and potential clinical applications will be highlighted.

Nanoparticle Synthesis and Their Integration into Polymer-Based Fibers for Biomedical Applications

The potential of nanoparticles as effective drug delivery systems combined with the versatility of fibers has led to the development of new and improved strategies to help in the diagnosis and treatment of diseases. Nanoparticles have extraordinary characteristics that are helpful in several applications, including wound dressings, microbial balance approaches, tissue regeneration, and cancer treatment. Owing to their large surface area, tailor-ability, and persistent diameter, fibers are also used for wound dressings, tissue engineering, controlled drug delivery, and protective clothing. The combination of nanoparticles with fibers has the power to generate delivery systems that have enhanced performance over the individual architectures. This review aims at illustrating the main possibilities and trends of fibers functionalized with nanoparticles, focusing on inorganic and organic nanoparticles and polymer-based fibers. Emphasis on the recent progress in the fabrication procedures of several types of nanoparticles and in the description of the most used polymers to produce fibers has been undertaken, along with the bioactivity of such alliances in several biomedical applications. To finish, future perspectives of nanoparticles incorporated within polymer-based fibers for clinical use are presented and discussed, thus showcasing relevant paths to follow for enhanced success in the field.

Corroded iron stent increases fibrin deposition and promotes endothelialization after stenting

Poststent restenosis is caused by insufficient endothelialization and is one of the most serious clinical complications of stenting. We observed a rapid endothelialization rate and increased fibrin deposition on the surfaces of the corroded iron stents. Thus, we hypothesized that corroded iron stents would promote endothelialization by increasing fibrin deposition on rough surfaces. To verify this hypothesis, we conducted an arteriovenous shunt experiment to analyze fibrin deposition in the corroded iron stents. We implanted a corroded iron stent in both the carotid and iliac artery bifurcations to elucidate the effects of fibrin deposition on endothelialization. Co-culture experiments were conducted under dynamic flow conditions to explore the relationship between fibrin deposition and rapid endothelialization. Our findings indicate that, from the generation of corrosion pits, the surface of the corroded iron stent was rough, and numerous fibrils were deposited in the corroded iron stent. Fibrin deposition in corroded iron stents facilitates endothelial cell adhesion and proliferation, which, in turn, promotes endothelialization after stenting. Our study is the first to elucidate the role of iron stent corrosion in endothelialization, pointing to a new direction for preventing clinical complications caused by insufficient endothelialization.

Biopolymeric Coatings for Local Release of Therapeutics from Biomedical Implants

The deployment of structures that enable localized release of bioactive molecules can result in more efficacious treatment of disease and better integration of implantable bionic devices. The strategic design of a biopolymeric coating can be used to engineer the optimal release profile depending on the task at hand. As illustrative examples, here advances in delivery of drugs from bone, brain, ocular, and cardiovascular implants are reviewed. These areas are focused to highlight that both hard and soft tissue implants can benefit from controlled localized delivery. The composition of biopolymers used to achieve appropriate delivery to the selected tissue types, and their corresponding outcomes are brought to the fore. To conclude, key factors in designing drug-loaded biopolymeric coatings for biomedical implants are highlighted.

Nano-embedded medical devices and delivery systems in interventional radiology

Nanomaterials research has significantly accelerated the development of the field of vascular and interventional radiology. The incorporation of nanoparticles with unique and functional properties into medical devices and delivery systems has paved the way for the creation of novel diagnostic and therapeutic procedures for various clinical disorders. In this review, we discuss the advancements in the field of interventional radiology and the role of nanotechnology in maximizing the benefits and mitigating the disadvantages of interventional radiology theranostic procedures. Several nanomaterials have been studied to improve the efficacy of interventional radiology interventions, reduce the complications associated with medical devices, improve the accuracy and efficiency of drug delivery systems, and develop innovative imaging modalities. Here, we summarize the recent progress in the development of medical devices and delivery systems that link nanotechnology in vascular and interventional radiology. This article is categorized under: Diagnostic Tools > Diagnostic Nanodevices Diagnostic Tools > In Vivo Nanodiagnostics and Imaging Therapeutic Approaches and Drug Discovery > Nanomedicine for Cardiovascular Disease.

Worldwide productivity and research trends of publications concerning stent application in acutely ruptured intracranial aneurysms: A bibliometric study

Background

Stenting is a common clinical practice to treat acutely ruptured intracranial aneurysm (RIA). Although multiple studies have demonstrated its long-term safety and effectiveness, there is currently a lack of bibliometric analysis on stent application in acutely RIA. This study sought to summarize the current status of research in this field and lay a foundation for further study.

Materials and methods

Related publications were searched in the Web of Science Core Collection (WoSCC) database. Data analysis and visualization were performed by R and CiteSpace software.

Results

A total of 275 publications published in English from 1997 to 2022 were included in this study. The growth of publications slowed down. The reference co-citation network identified 13 clusters with a significant network (Q = 0.7692) and convincing clustering (S = 0.9082). The research focus was acutely RIA and the application of stents during interventional procedures. The main trends of research were: (1) development of materials, and (2) safety of stent application in acutely RIA. The United States contributed the most articles, and Jianmin Liu was the most prolific author. Mayo Clinic was the leading institution in this field. Most articles were published in Interventional Neuroradiology.

Conclusions

This study analyzed the research trends, hotspots and frontiers of stent application in acutely RIA. It is our hope that the results obtained could provide useful information to researchers to get a clearer picture about their future research directions in this field.

Engineering Biomimetic Extracellular Matrix with Silica Nanofibers: From 1D Material to 3D Network

Biomaterials at nanoscale is a fast-expanding research field with which extensive studies have been conducted on understanding the interactions between cells and their surrounding microenvironments as well as intracellular communications. Among many kinds of nanoscale biomaterials, mesoporous fibrous structures are especially attractive as a promising approach to mimic the natural extracellular matrix (ECM) for cell and tissue research. Silica is a well-studied biocompatible, natural inorganic material that can be synthesized as morpho-genetically active scaffolds by various methods. This review compares silica nanofibers (SNFs) to other ECM materials such as hydrogel, polymers, and decellularized natural ECM, summarizes fabrication techniques for SNFs, and discusses different strategies of constructing ECM using SNFs. In addition, the latest progress on SNFs synthesis and biomimetic ECM substrates fabrication is summarized and highlighted. Lastly, we look at the wide use of SNF-based ECM scaffolds in biological applications, including stem cell regulation, tissue engineering, drug release, and environmental applications.

Anti-coagulation and anti-hyperplasia coating for retrievable vena cava filters by electrospraying and their performance in vivo

A novel drug eluting retrievable vena cava filter (RVCF) with a heparin-modified poly(ε-caprolactone) (hPCL) coating containing rapamycin was prepared by electrospraying. The in vitro drug release pattern showed that the encapsulated rapamycin in the coating can be sustainably released within one month, whereas activated partial thromboplastin time (APTT) and in vitro cell culture showed that the drug eluting RVCF can effectively extend blood clotting time and inhibit smooth muscle cell (SMC) and endothelial cell (EC) proliferation, respectively. The as-prepared drug eluting RVCF and corresponding commercial RVCF were implanted into the vena cava of sheep. The retrieval operation at a predetermined time point showed that the drug eluting RVCF had a much higher retrieval rate than the commercial RVCF. Comprehensive investigations, including histological, immunohistological and immunofluorescence analyses, on explanted veins were carried out. The results demonstrated that the as-prepared RVCF possessed excellent antihyperplasia properties in vivo, significantly improving the retrieval rate and extending the in vivo dwelling time in sheep. Consequently, the drug eluting RVCF has promising potential for application in the clinic to improve RVCF retrieval rates.

Recent advances in inhibiting atherosclerosis and restenosis: from pathogenic factors, therapeutic agents to nano-delivery strategies

Due to dominant atherosclerosis etiology, cardiovascular diseases (CVDs) remain the leading cause of morbidity and mortality worldwide. In clinical trials, advanced atherosclerotic plaques can be removed by angioplasty and vascular...

Advances in coatings on magnesium alloys for cardiovascular stents - A review

Magnesium (Mg) and its alloys, as potential biodegradable materials, have drawn wide attention in the cardiovascular stent field because of their appropriate mechanical properties and biocompatibility. Nevertheless, the occurrence of thrombosis, inflammation, and restenosis of implanted Mg alloy stents caused by their poor corrosion resistance and insufficient endothelialization restrains their anticipated clinical applications. Numerous surface treatment tactics have mainly striven to modify the Mg alloy for inhibiting its degradation rate and enduing it with biological functionality. This review focuses on highlighting and summarizing the latest research progress in functionalized coatings on Mg alloys for cardiovascular stents over the last decade, regarding preparation strategies for metal oxide, metal hydroxide, inorganic nonmetallic, polymer, and their composite coatings; and the performance of these strategies in regulating degradation behavior and biofunction. Potential research direction is also concisely discussed to help guide biological functionalized strategies and inspire further innovations. It is hoped that this review can give assistance to the surface modification of cardiovascular Mg-based stents and promote future advancements in this emerging research field.

An oxidative stress-responsive electrospun polyester membrane capable of releasing anti-bacterial and anti-inflammatory agents for postoperative anti-adhesion

Peritendinous adhesion, secondary to the repair surgery of tendon rupture or injury, is one of the most common causes of reoperation, owing to the proliferation of fibrous tissue and excessive collagen synthesis caused by the residing inflammatory cells. In this study, a smart oxidative stress-responsive electrospun polyester membrane (EPM) was fabricated as both physical barrier and reservoir of curcumin/celecoxib (CUR/CEL) to prevent peritendinous adhesion. The multicomponent EPM was designed to release the encapsulated drugs in response to oxidative stress of the local microenvironment induced by inflammation. Specifically, sulfides in the EPM were able to react with reactive oxygen species (ROS) and become hydrophilic sulfoxide or sulfone to accelerate the release rate of drugs and regulate oxidative stress level in the inflammatory site intelligently. The oxidation-sensitive multicomponent EPM loaded with CUR and CEL was tested for anti-adhesion capacity in vitro and in vivo. An excellent ROS-sensitive degradation behavior and good cytocompatibility with cell viability of above 85% were presented with the fabricated EPM. The CUR- or CEL-loaded EPM possessed a better anti-adhesion ability compared with EPM without the drugs. Nevertheless, they were inferior to the EPM simultaneously loaded with both drugs, where the adhesion rate and fibrous adhesion number in the EPM+CUR/CEL group were close to extremely low values of about zero, demonstrating that CUR and CEL could synergistically prevent peritendinous adhesion. More interestingly, the multicomponent EPM was able to react with the local oxidative stress, leading to a smart and sustained behavior of releasing approximately 80% of the drug within 20 days. Overall, the smart multicomponent EPM offers a promising barrier strategy to prevent peritendinous adhesion.

Influence of Elongation of Paclitaxel-Eluting Electrospun-Produced Stent Coating on Paclitaxel Release and Transport through the Arterial Wall after Stenting

It was previously shown that polycaprolactone (PCL)-based electrospun-produced paclitaxel (PTX)-enriched matrices exhibit long-term drug release kinetics and can be used as coatings for drug-eluting stents (DES). The installation of vascular stents involves a twofold increase in stent diameter and, therefore, an elongation of the matrices covering the stents, as well as the arterial wall in a stented area. We studied the influence of matrix elongation on its structure and PTX release using three different electrospun-produced matrices. The data obtained demonstrate that matrix elongation during stent installation does not lead to fiber breaks and does not interfere with the kinetics of PTX release. To study PTX diffusion through the expanded artery wall, stents coated with 5%PCL/10%HSA/3%DMSO/PTX and containing tritium-labeled PTX were installed into the freshly obtained iliac artery of a rabbit. The PTX passing through the artery wall was quantified using a scintillator β-counter. The artery retained the PTX and decreased its release from the coating. The retention of PTX by the arterial wall was more efficient when incubated in blood plasma in comparison with PBS. The retention/accumulation of PTX by the arterial wall provides a prolonged drug release and allows for the reduction in the dose of the drugs in electrospun-produced stent coatings.

Cheerios Effect Inspired Microbubbles as Suspended and Adhered Oral Delivery Systems

Oral drug administration has an important role in medical treatment. Attempts to develop drug microcarriers with desired features for extended duration and improved absorption is highly sought. Herein, inspired by the physical phenomenon of the Cheerios effect, a novel microfluidic electrospray microbubble carrier is presented that can suspend and actively adhere to the stomach for durable oral delivery. Compared with conventional fabrication methods, the present strategy shows stability and controllability of the product. Benefiting from their uniform hollow structure, the resultant microbubbles present the same behavior of the Cheerios and can float in the gastric juice, adhere and remain to the stomach wall, which thus enhance the duration and absorption of the loaded drugs. Based on these, it is demonstrated as a proof of concept that the dexamethasone-loaded hollow microbubbles can be applied to oral administration and remain suspended and adhered to the stomach of murine for more than 1 d, showing good therapeutic effect in treating lupus erythematosus. Thus, it is believed that the microbubbles floating system will find important values in long-term oral administration.

Synergistic Antibacterial and Anti-Inflammatory Effects of a Drug-Loaded Self-Standing Porphyrin-COF Membrane for Efficient Skin Wound Healing

Chronic wound infections resulting from severe bacterial invasion have become a major medical threat worldwide. Herein, we report a large-area, homogeneous, and self-standing porphyrin-covalent organic framework (COF)-based membrane with encapsulated ibuprofen (IBU) via an in situ interfacial polymerization and impregnation approach. The obtained IBU@DhaTph-membrane exhibits highly effective antibacterial and anti-inflammatory effects via synergistic light-induced singlet oxygen (¹ O₂ ) generation and controllable IBU release, which is well supported by in vitro experiments. In addition, the IBU@DhaTph-membrane-based biocompatible "band-aid" type dressing is fabricated, and its excellent anti-infection and tissue remodeling activities are fully evidenced by in vivo chronic wound-healing experiments. This study may inspire and promote the fabrication of many more new types of COF-based multifunctional biomaterials for various skin injuries in clinical medicine.

Polydopamine-modified collagen sponge scaffold as a novel dermal regeneration template with sustained release of platelet-rich plasma to accelerate skin repair: A one-step strategy

Although employed to release growth factors (GFs) for regenerative medicine, platelet-rich plasma (PRP) has been hindered by issues like burst effect. Based on collagen sponge scaffolds (CSSs) modified with polydopamine (pDA), a novel dermal regeneration template (DRT) was designed. However, whether it could efficiently deliver PRP and even foster wound healing remained unclear. In this work, after PRP was prepared and pDA-modified CSSs (pDA-CSSs) were fabricated, microscopic observation, GFs release assay and in-vitro biological evaluations of pDA-CSSs with PRP (pDA-CSS@PRP) were performed, followed by BALA-C/nu mice full-thickness skin defects implanted with pDA-CSS@PRP covered by grafted skins (termed as a One-step strategy). As a result, scanning electron microscope demonstrated more immobilized platelets on pDA-CSS' surface with GFs' controlled release via enzyme-linked immunosorbent assay, compared with CSSs. In line with enhanced in-vitro proliferation, adhesion and migration of keratinocytes & endothelial cells, pDA-CSS@PRP were histologically revealed to accelerate wound healing with less scar via rapid angiogenesis, arrangement of more mature collagen, guiding cells to spread, etc. In conclusion, pDA-CSSs have potential to serve as a novel DRT capable of delivering PRP, which may foster full-thickness skin defect healing by means of a One-step strategy.

Paclitaxel-loaded lignin particle encapsulated into electrospun PVA/PVP composite nanofiber for effective cervical cancer cell inhibition

Electrospun composite nanofibrous scaffolds have been regarded as a potential carrier for local drug delivery to prevent tumor recurrence. Herein, a model drug (paclitaxel) was creatively loaded into lignin nanoparticles (PLNPs) and then encapsulated into the polymer of poly (vinyl alcohol)/polyvinyl pyrrolidone which has been fabricated into a composite nanofibrous membrane (PVA/PVP-PLNPs) for use as a drug carrier using the electrospinning technique. The fabricated PVA/PVP-PLNPs membranes exhibited good particle distribution, mechanical properties, thermal stability and biocompatibility. In vitro experiments showed that combining lignin nanoparticles by electrospinning not only improved the drug release profile, but also enhanced the hydrophilicity of nanofibrous membranes which was beneficial to cell adhesion and proliferation. Cellular experiments demonstrated that PVA/PVP-2%PLNPs membrane showed good cell inhibition ability, and the cell survival rate was only 21% at day 7. It indicates that the as-prepared PVA/PVP-PLNPs composite nanofibers are promising candidates for local anticancer therapy.

Arsenic trioxide-eluting electrospun nanofiber-covered self-expandable metallic stent reduces granulation tissue hyperplasia in rabbit trachea

Stent-related granulation tissue hyperplasia is a major complication that limits the application of stents in airways. In this study, an arsenic trioxide-eluting electrospun nanofiber-covered self-expandable metallic stent (ATO-NFCS) was developed. Poly-L-lactide-caprolactone (PLCL) was selected as the drug-carrying polymer. Stents with two different ATO contents (0.4% ATO/PLCL and 1.2% ATO/PLCL) were fabricated. The in vitro release in simulated airway fluid suggested that the total ATO release time was 1 d. The growth of human embryonic pulmonary fibroblasts (CCC-HPF-1), normal human bronchial epithelial cells and airway smooth muscle cells was inhibited by ATO. When embedded in paravertebral muscle, the nanofiber membrane showed good short-term and long-term biological effects. In an animal study, placement of the ATO-NFCS in the trachea through a delivery system under fluoroscopy was feasible. The changes in liver and kidney function 1 and 7 d after ATO-NFCS placement were within the normal range. On pathological examination, the heart, liver, spleen, lungs and kidneys were normal. The effectiveness of the ATO-NFCS in reducing granulation tissue hyperplasia and collagen deposition was demonstrated in the rabbit airway (n = 18) at 4 weeks. The present study preliminarily investigated the efficacy of the ATO-NFCS in reducing granulation tissue formation in the trachea of rabbits. The results suggest that the ATO-NFCS is safe in vivo, easy to place, and effective for the suppression of granulation tissue formation.

Tissue engineering stent model with long fiber-reinforced thermoplastic technique

This study aims to construct tissue engineering stents by using the long fiber-reinforced thermoplastic (LFT) technique to develop artery stents. The experimental method combines fibers, the LFT technique, and electrospinning technique. First, the biodegradable polyvinyl alcohol yarns are twisted and coated in polycaprolactone/polyethylene glycol blends through the LFT technique. Next, the weft-knitting and heat treatment are used to establish the stent structure, after which poly(ethylene oxide) (PEO) is electrospun to coat the stents. The morphology, mechanical, and biological properties of tissue engineering stents are evaluated. The test results indicated that the use of the LFT technique retains the softness of filaments, which facilitates the subsequent weft-knitting process. The coating of blends and electrospinning of PEO have a positive influence on the tissue engineering stents, as demonstrated by the tensile strength of 59.93 N and compressive strength of 6.10 N. Moreover, the in vitro degradation of stents exhibits a stabilized process. The water contact angle is 20.33°, and the cell survival rate in 24 h is over 80%. The proposed tissue engineering stents are good candidates for artery stent structure.

A zwitterionic hydrogel coated titanium surface with high-efficiency endothelial cell selectivity for rapid re-endothelialization

Coronary stent implantation is an effective procedure for percutaneous coronary intervention treatment. However, its long-term safety and efficacy are still hindered by the in-stent restenosis and late thrombus formation. Herein, an anti-biofouling and endothelial cell selective zwitterionic hydrogel coating was developed to simultaneously enhance the nonspecific resistance and rapid re-endothelialization of the titanium surface. An endothelial cell selective peptide, REDV, could be simply conjugated on the zwitterionic carboxybetaine (CB) hydrogel to prepare the REDV/CB coating. It was found that the REDV/CB hydrogel layer maintained antifouling properties, which could inhibit the protein adsorption, bacterial adhesion, platelet activation and aggregation, and smooth muscle cell proliferation. More importantly, the co-culture study confirmed that the conjugated REVD peptide could specifically capture endothelial cells and promote their migration and proliferation, and simultaneously decrease the adhesion and proliferation of smooth muscle cells. Therefore, the antifouling and endothelial cell selective coating proposed in this work provides a promising strategy to develop an intravascular stent for promoted re-endothelialization and inhibited neointimal hyperplasia in clinical applications.

Surface Engineering of Cardiovascular Devices for Improved Hemocompatibility and Rapid Endothelialization

Cardiovascular devices have been widely applied in the clinical treatment of cardiovascular diseases. However, poor hemocompatibility and slow endothelialization on their surface still exist. Numerous surface engineering strategies have mainly sought to modify the device surface through physical, chemical, and biological approaches to improve surface hemocompatibility and endothelialization. The alteration of physical characteristics and pattern topographies brings some hopeful outcomes and plays a notable role in this respect. The chemical and biological approaches can provide potential signs of success in the endothelialization of vascular device surfaces. They usually involve therapeutic drugs, specific peptides, adhesive proteins, antibodies, growth factors and nitric oxide (NO) donors. The gene engineering can enhance the proliferation, growth, and migration of vascular cells, thus boosting the endothelialization. In this review, the surface engineering strategies are highlighted and summarized to improve hemocompatibility and rapid endothelialization on the cardiovascular devices. The potential outlook is also briefly discussed to help guide endothelialization strategies and inspire further innovations. It is hoped that this review can assist with the surface engineering of cardiovascular devices and promote future advancements in this emerging research field.

Sirolimus-Eluting Electrospun-Produced Matrices as Coatings for Vascular Stents: Dependence of Drug Release on Matrix Structure and Composition of the External Environment

Although a number of drug-eluting coatings for vascular stents (VSs) have been developed and are in commercial use, more efficient stent coatings and drug delivery systems are needed. Sirolimus (SRL) is a clinically important drug with antiproliferative and immunosuppressive activities that is widely used for coating stents. Here, we characterized SRL-enriched matrices, intended for coating vascular stents, that were produced by electrospinning (ES) on a drum collector from a solution of polycaprolactone (PCL) and human serum albumin (HSA), 1,1,1,3,3,3-hexafluoroisopropanol (HFIP), dimethyl sulfoxide (DMSO), and SRL. The release of tritium-labeled SRL (³H-SRL) from matrices in phosphate-buffered saline (PBS) or human blood plasma (BP) was studied. The introduction of DMSO in the ES blend decreased SRL release. The use of BP significantly accelerated SRL release through binding with serum biomolecules. The exchange of PBS or BP after every time point also increased SRL release. The maximum SRL release in BP was observed at 3 days. The matrices produced from the ES solution with DMSO and HSA released no more than 80% SRL after 27 days in BP, even under medium exchange conditions. Therefore, PCL-based matrices containing HSA, SRL, and DMSO can be used for coating VSs with prolonged SRL delivery.

Electrospun fibers: an innovative delivery method for the treatment of bone diseases

INTRODUCTION

The treatment performances of current surgical therapeutic materials for injuries caused by high-energy trauma, such as prolonged bone defects, nerve-fiber disruptions, and repeated spasms or adhesions of vascular tendons after repair, are poor. Drug-loaded electrospun fibers have become a novel polymeric material for treating orthopedic diseases owing to their three-dimensional structures, thus providing excellent controlled drug-release responses and high affinity with local tissues. Herein, we reviewed the morphology of electrospun nanofibers, methods for loading drugs on the fibers, and modification methods to improve drug permeability and bioavailability. We highlight innovative applications of drug-loaded electrospun fibers in different treatments, including bone and cartilage defects, tendon and soft-tissue adhesion, vascular remodeling, skin grafting, and nervous-system injuries.

AREAS COVERED

With the rapid development of electrospinning technologies and advancement of tissue engineering, drug-loaded electrospun fibers are becoming increasingly important in controlled drug release, wound closure, and tissue regeneration and repair.

EXPERT OPINION

Drug-loaded electrospun fibers exhibit a broad range of application prospects and great potential in treating orthopedic diseases. Accordingly, a plethora of novel treatments utilizing the different morphological features of electrospun fibers, the distinctive pharmacokinetics, pharmacodynamics characteristics of different drugs, and the diverse onset characteristics of different diseases, is proposed.

Folic Acid and PEI Modified Mesoporous Silica for Targeted Delivery of Curcumin

Nano anti-cancer drug carriers loaded with antineoplastic drugs can achieve targeted drug delivery, which enriches drugs at tumor sites and reduces the toxic side effects in normal tissues. Mesoporous silica nanoparticles (MSN) are good nano drug carriers, as they have large specific surface areas, adjustable pore sizes, easily modifiable surfaces, and good biocompatibility. In this work, polyethyleneimine (PEI) grafted MSN were modified with folic acid (FA) as an active target molecule using chemical methods. The product was characterized by SEM, TEM, Zetasizer nano, FTIR, and an N₂ adsorption and desorption test. MSN-PEI-FA are porous nano particles with an average particle size of approximately 100 nm. In addition, the loading rate and release behavior of MSN-PEI-FA were studied with curcumin as a model drug. The results show that when loading curcumin to MSN-PEI-FA at 7 mg and 0.1 g, respectively, the encapsulation efficiency was 90% and the cumulative release rate reached more than 50% within 120 h at pH = 5. This drug delivery system is suitable for loading fat-soluble antineoplastic drugs for sustained release and pH sensitive delivery.