Power generation and microbial community analysis in microbial fuel cells: A promising system to treat organic acid fermentation wastewater

Electrochemically active biofilms responses to gadolinium stress during wastewater treatment in bioelectrochemical systems

Gadolinium-based contrast agents used in magnetic resonance imaging (MRI) contribute to increasing gadolinium(III) [Gd(III)] concentrations in aquatic environments, as conventional wastewater treatment plants lack effective removal mechanisms. This study investigated the potential of single-chamber microbial fuel cells (SCMFCs) for Gd(III) removal, focusing on removal efficiency and the physiological responses of electrochemically active biofilms. SCMFCs demonstrated exceptional Gd(III) removal efficiency exceeding 99.75 ± 0.007 % across various initial concentrations (10-60 mg/L). Power output and chemical oxygen demand (COD) removal efficiency showed dose-dependent responses to Gd(III) stress, with maximum power output decreasing from 479.56 mV to 260.43 mV as Gd(III) increased from 0 to 60 mg/L. COD removal efficiency declined from 96.49 ± 1.2 % to 90.23 ± 1.6 % over the same range. Microbial community analysis revealed selective enrichment of exoelectrogens at lower Gd(III) concentrations, with Geobacter relative abundance decreasing from 11.14 % to 1.82 %. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) analyses demonstrated that elevated Gd(III) concentrations reduced electrochemically active bacterial colonization in anode biofilms. Fourier-transform infrared spectroscopy (FTIR) identified specific functional groups associated with Gd(III) biosorption, while predictive functional profiling indicated upregulation of metal resistance genes under Gd(III) exposure. These findings demonstrate the effectiveness of SCMFCs in Gd(III) removal from wastewater while elucidating microbial adaptation mechanisms to rare earth element exposure, providing insights for developing sustainable treatment solutions for emerging contaminants.

Synchronous production of bioethanol and short-chain fatty acids associated with microbial mechanisms via the short-term cultivation of waste molasses inoculated with Aspergillus oryzae

This study proposes a novel approach for the concurrent production of short-chain fatty acids (SCFAs) and bioethanol, during a 96 h cultivation of waste molasses (with direct air exposure) inoculated with Aspergillus oryzae using vermiculite as a carrier. Results showed that fungal-bacterial symbiotes were formed by enriching acidogens for the bioconversion of SCFAs, such as Enterococcus, Bacillus and Pseudomonas and bioethanol producers, like Klebsiella, Candida tropicalis, Aspergillus oryzae and Barnettozyma californica. The Aspergillus oryzae was found to play various diverse roles during the short-term cultivation process, secreting hydrolase (i.e. α-amylase) for the hydrolysis of waste molasses and contributing to the formation of fungal-bacterial symbiotes. Furthermore, the mechanisms of fungal-bacterial interaction related to simultaneous generation of SCFAs and bioethanol were investigated. Consequently, the cultivation liquid obtained could feasibly be used as a low-cost carbon source for enhancing total nitrogen (TN) removal in the process of low C/N ratio wastewater treatment.

Stable isotope labeling and functional gene prediction elucidate the carbon metabolism in fermentative bacteria and microalgae coupling system

The application of the fermentative bacteria and microalgae coupling system in the wastewater treatment has been studied, but there remains few knowledge regarding the organic and inorganic carbon metabolism within this system. In this study, the carbon metabolism of microalgae and fermentative bacteria was elucidated by 13C stable isotope labeling and functional gene prediction, respectively. The 13C glucose and 13C NaHCO3 were used as stable isotope tracers to clarify the organic and inorganic carbon metabolism of microalgae, indicating that approximately 71.5 % of the Acetyl-CoA in microalgae was synthesized from organic carbon sources, while 26.8 % was synthesized through the utilization of inorganic carbon sources. Inorganic carbon sources can enhance the activity of photosynthetic system and facilitate the Calvin cycle. Considering the adequate organic carbon sources and insufficient inorganic carbon sources in the fermentative bacteria and microalgae coupling system, NaHCO3 was added to improve carbon utilization of microalgae. The maximum microalgal lipid yield reached 1130.37 mg/L with 1000 mg/L NaHCO3 supplementation. Functional gene prediction was used to analysis the effect of various carbon composition on the bacterial carbon metabolism. Notably, the additional inorganic carbon sources increased the abundance of bacterial functional genes associated with the fermentation and acetic acids synthesis, which was advantageous for VFAs production and further promoted microalgae growth. This study can gain a deeper understanding of microbial metabolic mechanisms during the operation of fermentative bacteria and microalgae system, and improve its sustained operational stability.

Optimization of microbial fuel cell performance application to high sulfide industrial wastewater treatment by modulating microbial function

Microbial fuel cells (MFCs) are innovative eco-friendly technologies that advance a circular economy by enabling the conversion of both organic and inorganic substances in wastewater to electricity. While conceptually promising, there are lingering questions regarding the performance and stability of MFCs in real industrial settings. To address this research gap, we investigated the influence of specific operational settings, regarding the hydraulic retention time (HRT) and organic loading rate (OLR) on the performance of MFCs used for treating sulfide-rich wastewater from a canned pineapple factory. Experiments were performed at varying hydraulic retention times (2 days and 4 days) during both low and high seasonal production. Through optimization, we achieved a current density generation of 47±15 mA/m2, a COD removal efficiency of 91±9%, and a sulfide removal efficiency of 86±10%. Microbiome analysis revealed improved MFC performance when there was a substantial presence of electrogenic bacteria, sulfide-oxidizing bacteria, and methanotrophs, alongside a reduced abundance of sulfate-reducing bacteria and methanogens. In conclusion, we recommend the following operational guidelines for applying MFCs in industrial wastewater treatment: (i) Careful selection of the microbial inoculum, as this step significantly influences the composition of the MFC microbial community and its overall performance. (ii) Initiating MFC operation with an appropriate OLR is essential. This helps in establishing an effective and adaptable microbial community within the MFCs, which can be beneficial when facing variations in OLR due to seasonal production changes. (iii) Identifying and maintaining MFC-supporting microbes, including those identified in this study, should be a priority. Keeping these microbes as an integral part of the system's microbial composition throughout the operation enhances and stabilizes MFC performance.

Engineering extracellular electron transfer to promote simultaneous brewing wastewater treatment and chromium reduction

Microbial fuel cell (MFC) technology has been developed for wastewater treatment in the anodic chamber, and heavy metal reduction in the cathodic chamber. However, the limited extracellular electron transfer (EET) rate of exoelectrogens remained a constraint for practical applications of MFCs. Here, a MFC system that used the electricity derived from anodic wastewater treatment to drive cathodic Cr6+ reduction was developed, which enabled an energy self-sustained approach to efficiently address Cr6+ contamination. This MFC system was achieved by screening exoelectrogens with a superior EET rate, promoting the exoelectrogenic EET rate, and constructing a conductive bio-anode. Firstly, Shewanella algae-L3 was screened from brewing wastewater acclimatized sludge, which generated power density of 566.83 mW m-2. Secondly, to facilitate EET rate, flavin synthesis gene operon ribADEHC was overexpressed in engineered S. algae-L3F to increase flavins biosynthesis, which promoted the power density to 1233.21 mW m-2. Thirdly, to facilitate interface electron transfer, carbon nanotube (CNT) was employed to construct a S. algae-L3F-CNT bio-anode, which further enhanced power density to 3112.98 mW m-2. Lastly, S. algae-L3F-CNT bio-anode was used to harvest electrical energy from brewing wastewater to drive cathodic Cr6+ reduction in MFC, realizing 71.43% anodic COD removal and 98.14% cathodic Cr6+ reduction. This study demonstrated that enhanced exoelectrogenic EET could facilitate cathodic Cr6+ reduction in MFC.

Paradigm shift in Nutrient-Energy-Water centered sustainable wastewater treatment system through synergy of bioelectrochemical system and anaerobic digestion

With advancements in research and the necessity of improving the performance of bioelectrochemical system (BES), coupling anaerobic digestion (AD) with BES is crucial for energy gain from wastewater and bioremediation. Hybridization of BES-AD concept opens new avenues for pollutant degradation, carbon capture and nutrient-resource recovery from wastewater. The strength of merging BES-AD lies in synergy, and this approach was employed to differentiate fads from strategies with the potential for full-scale implementation and making it an energy-positive system. The integration of BES and AD system increases the overall performance and complexity of combined system and the cost of operation. From a technical standpoint, the primary determinants of BES-AD feasibility for field applications are the scalability and economic viability. High potential market for such integrated system attract industrial partners for more industrial trials and investment before commercialization. However, BES-AD with high energy efficacy and negative economics demands performance boost.

Insight into the mechanism of nutrients removal and response regulation of denitrifying phosphorus removal system under calcium ion stress

The influent quality is an important factor affecting the nutrients removal and operational stability of denitrifying phosphorus removal (DPR) system. This study investigated the effects of calcium ion (Ca2+) on the nutrients removal, nitrogen oxide (N2O) release, microbial community, and quorum sensing in DPR system. Results showed that high accumulation of Ca2+ had a significant impact on the carbon footprint of DPR system. Specifically, N2O release reached 2.11 mg/L under Ca2+ of 150 mg/L, which represented 214.93% increase compared to 0 mg/L of Ca2+. The DPR system demonstrated its adaptability to elevated Ca2+ concentrations by modifying key enzyme activities involved in nitrogen and phosphorus removal, altering the microbial community structure, and adjusting the type and content of signal molecules. These findings hold significant implications for understanding the stress mechanism of Ca2+ on DPR system, ultimately aiding in the maintenance and enhancement of stable operational performance in biological wastewater treatment process.

Performance and response of coupled microbial fuel cells for enhanced anaerobic treatment of azo dye wastewater with simultaneous recovery of electrical energy

The anaerobic baffled reactor (ABR) is an anaerobic bioreactor that uses baffles to separate the working area into multiple reaction zones. The ABR-microbial fuel cell (MFC) reactor was constructed by embedding MFC in each reaction zone of the ABR. Its degradation of azo dye type (acid mordant red) wastewater and microbial power generation performance were investigated. For different electrode area ratios, the best enhanced treatment and electrical energy output of the coupled system was achieved with an anode/cathode area ratio of 1:1. Compared with the electrode area ratio of 2:1 and 1:2, the power density increased by 82.5% and 80.6%, and the Coulomb efficiency increased by 133.3% and 64.7%. In addition, the best enhanced treatment of printing and dyeing wastewater was achieved by ABR-MFC at 1:1. At a dye concentration of 200 mg/L and a sucrose concentration of 1000 mg/L, the coupled system obtained a COD removal of 92.85% and a chromaticity removal of 96.2%, which achieved a relative COD and chromaticity removal improvement of 1.82% and 2.64%, respectively, relative to the ABR. Scanning electron microscopy (SEM) observation of the electrodes at 1:1 revealed that more microorganisms were attached to the anode surface of the coupled system, the particle size of the granular sludge within the system was larger, and the UV scanning pattern showed lower dye concentration in the water. In conclusion, the microbial fuel cell enhanced anaerobic treatment of dyeing wastewater was the most effective when the electrode area ratio was 1:1, and the best electrical energy output was obtained at the same time. ABR-MFC provides a new idea for the enhanced treatment of dyeing wastewater and electrical energy production.

Response of aerobic activated sludge to edible oil exposure: Extracellular polymeric substance (EPS) characteristics and microbial community

Aerobic activated sludge is widely used to degrade edible oil wastewater in wastewater treatment plants. During this process, the observed poor organics removal performance might be caused by poor sludge settling performance, which might be influenced by extracellular polymeric substances (EPS) and the structure of the microbial community. However, this hypothesis was not confirmed. Thus, this study investigated the response of activated sludge to 50% and 100% edible oil exposure in comparison to glucose, focusing on organics removal performance, characteristics of sludge, EPS, and microbial community structure. Results showed that both concentrations of edible oil influenced the systems' performance, although 100% edible oil showed more significant negative effects than 50% edible oil. The mechanisms behind the influence of edible oil on the aerobic activated sludge system and the differences between the different concentrations of edible oil were revealed. The worse system performance in the edible oil exposure system was due to the worse sludge settling performance, which was significantly affected by edible oil (p < 0.05). The sludge settling performance was mainly inhibited by promoting the formation of floating particles and the enrichment of filamentous bacteria in the 50% edible oil exposure system; biosurfactant secretion was also speculated as the reason, in addition to the above factors, in the 100% edible oil exposure system. The macroscopic largest floating particles, highest total relative abundance of foaming bacteria and biosurfactant production genera (34.32%), lowest surface tension (43.7 mN/m), and highest emulsifying activity (E₂₄ = 25%) of EPS in 100% edible oil exposure systems provide strong evidence.

Sludge source-redox mediators obtainment and availability for enhancing bioelectrogenesis and acidogenesis: Deciphering characteristics and mechanisms

Anaerobic biological treatment was regarded as one of promising options for realizing concurrent WAS reduction, stabilization and bioenergy/bioresource recycle. But the relatively low treatment efficiency limited its spreading application toward larger scale considerably in China. Aimed at such barrier, this study offered a novel enhancing strategy for achieving high-efficiency of bioenergy/bioresource recycle from WAS anaerobic treatment via improving bioelectrogenesis/acidogenesis using sludge source-redox mediators (SSRMs). SSRMs not only facilitated bioeletrogenesis with an increasing efficiency of 36% for voltage output and 39% for bioelectricity bioconversion, but also enhanced acidogenesis of WAS with a mean elevating efficiency of 37.5% of volatile fatty acids (VFAs) production within 5 d Mechanistic investigations indicated that SSRMs had a potential influence on improving the protein and carbohydrate metabolisms-related genes' expression for enhancing bioelectrogenesis and acidogenesis. Moreover, SSRMs exerted roles of electrochemical "catalysts" or as terminal electron acceptors with affecting functional proteins of complexes of Ⅰ and Ⅳ in electron transfer chains for improving electron transfer efficiency. Meanwhile, the core members' abundance, microbial diversity and community distributive evenness were prompted concurrently for carrying out superior bioelectrogenesis and acidogenesis. A schematic illustration was established for demonstrating the mechanism of SSRMs for enhancing bioelectrogenesis and acidogenesis via changing microbial metabolism functions, enhancing electron transfer efficiency, and regulating functional genes' expression of functional proteins (up-regulating cytochrome c oxidase and down-regulating-NADH dehydrogenase). This study provided an effective enhancing strategy for facilitating WAS bioconversion to bioenergy/bioresource with well-process sustainability.

Microbial Fuel Cell Construction Features and Application for Sustainable Wastewater Treatment

A microbial fuel cell (MFC) is a system that can generate electricity by harnessing microorganisms' metabolic activity. MFCs can be used in wastewater treatment plants since they can convert the organic matter in wastewater into electricity while also removing pollutants. The microorganisms in the anode electrode oxidize the organic matter, breaking down pollutants and generating electrons that flow through an electrical circuit to the cathode compartment. This process also generates clean water as a byproduct, which can be reused or released back into the environment. MFCs offer a more energy-efficient alternative to traditional wastewater treatment plants, as they can generate electricity from the organic matter in wastewater, offsetting the energy needs of the treatment plants. The energy requirements of conventional wastewater treatment plants can add to the overall cost of the treatment process and contribute to greenhouse gas emissions. MFCs in wastewater treatment plants can increase sustainability in wastewater treatment processes by increasing energy efficiency and reducing operational cost and greenhouse gas emissions. However, the build-up to the commercial-scale still needs a lot of study, as MFC research is still in its early stages. This study thoroughly describes the principles underlying MFCs, including their fundamental structure and types, construction materials and membrane, working mechanism, and significant process elements influencing their effectiveness in the workplace. The application of this technology in sustainable wastewater treatment, as well as the challenges involved in its widespread adoption, are discussed in this study.

Putting the electro-bugs to work: A systematic review of 22 years of advances in bio-electrochemical systems and the parameters governing their performance

Wastewater treatment using bioelectrochemical systems (BESs) can be considered as a technology finding application in versatile areas such as for renewable energy production and simultaneous reducing environmental problems, biosensors, and bioelectrosynthesis. This review paper reports and critically discusses the challenges, and advances in bio-electrochemical studies in the 21st century. To sum and critically analyze the strides of the last 20+ years on the topic, this study first provides a comprehensive analysis on the structure, performance, and application of BESs, which include Microbial Fuel Cells (MFCs), Microbial Electrolysis Cells (MECs) and Microbial Desalination Cells (MDCs). We focus on the effect of various parameters, such as electroactive microbial community structure, electrode material, configuration of bioreactors, anode unit volume, membrane type, initial COD, co-substrates and the nature of the input wastewater in treatment process and the amount of energy and fuel production, with the purpose of showcasing the modes of operation as a guide for future studies. The results of this review show that the BES have great potential in reducing environmental pollution, purifying saltwater, and producing energy and fuel. At a larger scale, it aspires to facilitate the path of achieving sustainable development and practical application of BES in real-world scenarios.

General aspects and novel PEMss in microbial fuel cell technology: A review

The current scenario of energy production is mostly shifted towards sustainable renewable energy sources. Other than the energy production from natural resources such as sun, wind and water, microbial fuel cell system (MFC) has earned attraction in recent times. These microbial fuel cell systems are bioelectrochemical cell that possesses a unique ability to generate power as well as treats wastewater simultaneously. In this paper, an overview of the microbial fuel cell system and the effect of significant components on the performance of microbial fuel cell systems are reviewed. Firstly, the importance of the MFC system in power generation, its components, the working principle and various configurations of the MFC were briefly introduced. Biofilm plays a major role in the MFC system. Thus the importance of bio film, bio film formation and characterization techniques are summarised. Further, the review mainly addresses the mechanism of conventional and novel membrane materials on the performance of the MFC system. In addition, special emphasis on ceramic-based materials in the MFC system is presented. Finally, recent applications of the MFC systems are discussed.

Synergic role of ferrate and nitrite for triggering waste activated sludge solubilisation and acidogenic fermentation: Effectiveness evaluation and mechanism elucidation

Enhancing anaerobic treatment efficiency of waste activated sludge (WAS) toward preferable resource recovery would be an important requirement for achieving carbon-emission reduction, biosolids minimization, stabilization and security concurrently. This study demonstrated the synergic effect of potassium ferrate (PF) and nitrite on prompting WAS solubilisation and acidogenic fermentation toward harvesting volatile fatty acids (VFAs). The results indicated the PF+NaNO₂ co-pretreatment boosted 7.44 times and 1.32 times higher WAS solubilisation [peak soluble chemical oxygen demand (SCOD) of 2680 ± 52 mg/L] than that by the single nitrite- and PF-pretreatment, respectively, while about 2.77 times and 2.11 times higher VFAs production were achieved (maximum VFAs accumulation of 3536.25 ± 115.24 mg COD/L) as compared with the single pretreatment (nitrite and PF)-fermentations. Afterwards the WAS dewaterability was improved simultaneously after acidogenic fermentation. Moreover, a schematic diagram was established for illustrating mechanisms of the co-pretreatment of PF and nitrite for enhancing the VFAs generation via increasing key hydrolytic enzymes, metabolic functional genes expression, shifting microbial biotransformation pathways and elevating abundances of key microbes in acidogenic fermentation. Furthermore, the mechanistic investigations suggested that the PF addition was conducive to form a relatively conductive fermentation environment for enhancing electron transfer (ET) efficiency, which contributed to the VFAs biotransformation positively. This study provided an effective strategy for enhancing the biodegradation/bioconversion efficiency of WAS organic matters with potential profitable economic returns.

A Review of Recent Advances in Microbial Fuel Cells: Preparation, Operation, and Application

The microbial fuel cell has been considered a promising alternative to traditional fossil energy. It has great potential in energy production, waste management, and biomass valorization. However, it has several technical issues, such as low power generation efficiency and operational stability. These issues limit the scale-up and commercialization of MFC systems. This review presents the latest progress in microbial community selection and genetic engineering techniques for enhancing microbial electricity production. The summary of substrate selection covers defined substrates and some inexpensive complex substrates, such as wastewater and lignocellulosic biomass materials. In addition, it also includes electrode modification, electron transfer mediator selection, and optimization of operating conditions. The applications of MFC systems introduced in this review involve wastewater treatment, production of value-added products, and biosensors. This review focuses on the crucial process of microbial fuel cells from preparation to application and provides an outlook for their future development.

Synchronous bio-degradation and bio-electricity generation in a Microbial Fuel Cell with aged and fresh leachate from the identical subtropical area

Seasonal leachate from both sealed and operating landfill in the identical district were employed as the sole substrate in the Microbial Fuel Cell (MFC) to evaluate the power output performance and aqueous organic waste disposal. The electrical performance was characterized to study the power generation, while the Chemical Oxygen Demand (COD) removal ratio and Coulombic Efficiency (CE) were calculated to illustrate the substrate disposal effect. In addition, Scanning Electron Microscope (SEM) on the operated anode was conducted to preliminarily explain the microbial community difference, and the phylogenetic tree constructed on the cultivated microorganism was an insight into the dominant bacteria suitable for leachate degradation. It was found that the MFCs inoculated with seasonal leachate from both sealed and operating landfill could generate electricity successfully. Although the fresh leachate-inoculated MFCs had better electrical output performance (22.7-25.6 W/m³ versus 6.61-7.48 W/m³) and COD removal efficiency (55.8%∼61.7% versus 47.7%∼51.4%), the CEs were only 4.3%∼7.6%, which were lower than the aged leachate inoculated group (5.9%∼11.3%). Based on the SEM images and the phylogenetic tree of the operated anode, the composition impacts on the microbial community and power output performance were verified, which was instructive for the leachate disposal in the MFC.

Characterization of Microbial Communities in Wastewater Treatment Plants Containing Heavy Metals Located in Chemical Industrial Zones

Water pollution caused by heavy metals (HMs) poses a serious risk to human health and the environment and can increase the risk of diabetes, cancer, and hypertension in particular. In this study, two full-scale wastewater treatment plants (WWTPs) in industrial zones in southern China were selected to analyze the microbial community structure, diversity, similarity, and differentiation in the anoxic/oxic (AO) and anoxic/oxic membrane bioreactor (AO-MBR) units under the stress of HMs. High-throughput sequencing showed that microbial diversity and abundance were higher in the AO process than in the AO-MBR process. In the two WWTPs, the common dominant phyla were Proteobacteria and Bacteroidetes, while the common dominant genera were Gemmatimonadaceae, Anaerolineaceae, Saprospiraceae, and Terrimonas. Manganese (Mn) and zinc (Zn) positively correlated with Saccharimonadales, Nakamurella, Micrococcales, and Microtrichales, whereas copper (Cu) and iron (Fe) positively correlated with Longilinea and Ferruginibacter. Additionally, the relative abundances of Chloroflexi, Patescibacteria, and Firmicutes differed significantly (p < 0.05) between the two processes. These results may provide comprehensive outlooks on the characterization of microbial communities in WWTPs, which could also help to reduce the potential environmental risks of the effluent from WWTPs located in industrial zones.

Advanced bioelectrochemical system for nitrogen removal in wastewater

Nitrogen (N) pollution in water has become a serious issue that cannot be ignored due to the harm posed by excessive nitrogen to environmental safety and human health; as such, N concentrations in water are strictly limited. The bioelectrochemical system (BES) is a new method to remove excessive N from water, and has attracted considerable attention. Compared with other methods, it is highly efficient and has low energy consumption. However, the BES has not been applied for N removal in practice due to lack of in-depth research on the mechanism and construction of high-performance electrodes, separators, and reactor configurations; this highlights a need to review and examine the efforts in this field. This paper provides a comprehensive review on the current BES research for N removal focusing on the reaction principles, reactor configurations, electrodes and separators, and treatment of actual wastewater; the corresponding performances in these realms are also discussed. Finally, the prospects for N removal in water using the BES are presented.

Promoting enrichment of sulfur-oxidizing autotrophic denitrifiers via static magnetic fields: Performance and mechanism of magnetic biological effects

Sulfur-driven autotrophic denitrification (SADN) is a promising technology for nitrogen removal from wastewater. In this study, different-strength SMFs (0, 5, 20, 50, 70 mT) were evaluated to investigate the potential of external static magnetic field (SMF) for enriching sulfur-oxidizing autotrophic denitrifiers (SOAD). 50-mT and 70-mT SMFs were most suitable to accelerate the growth of SOAD and the elimination of non-SOAD. The relative abundance of Thiobacillus significantly increased (p < 0.01) from 6.26% in control reactor to 36.15% under 50 mT and 52.51% under 70 mT. Under 50 mT, Thiobacillus denitrificans accumulated most rapidly, with the largest population. Furthermore, functional gene forecast by high-throughput and metagenomic sequencing indicated that SMF changed the two-component system, the adenosine 5'-monophosphate-activated protein kinase (AMPK) signaling system, the phosphotransferase system (PTS), as well as N/S-related enzymes to regulate stress-response and promote the growth of SOAD. The findings indicated that SMF accelerated the start-up of SADN.

Effects of ofloxacin on the structure and function of freshwater microbial communities

Ofloxacin (OFL) is a broad-spectrum fluoroquinolone antibiotic frequently used in clinic for treating bacterial infections. The discharged OFL would inevitably enter into aquatic ecosystems, affecting the growth of non-target microorganisms, which may result in micro-ecosystem imbalance. To the best of our knowledge, researches in this area are rather sparse. The present study evaluated the response of photosynthetic microorganisms (cyanobacteria, eukaryotic algae) and aquatic microbial community to OFL in a microcosm. Results showed that ofloxacin presented an inhibitory effect on the growth Microcystis aeruginosa. Although 0.1 mg/L OFL has no significant impact on alpha diversity of the microbial communities, it obviously altered the structure and decreased the species interaction of prokaryotic community by reducing the capacities of nitrogen fixation, photosynthetic and metabolic capacity of the microbial community. This study pointed out that the residual OFL in water would disturb the balance of the aquatic micro-ecology, suggesting that more attentions should be given to the negative effects of antibiotics and other bioactive pollutants on aquatic environments.

Recent progress in microbial fuel cells for industrial effluent treatment and energy generation: Fundamentals to scale-up application and challenges

Microbial fuel cells (MFCs) technology have the potential to decarbonize electricity generation and offer an eco-friendly route for treating a wide range of industrial effluents from power generation, petrochemical, tannery, brewery, dairy, textile, pulp/paper industries, and agro-industries. Despite successful laboratory-scale studies, several obstacles limit the MFC technology for real-world applications. This review article aimed to discuss the most recent state-of-the-art information on MFC architecture, design, components, electrode materials, and anodic exoelectrogens to enhance MFC performance and reduce cost. In addition, the article comprehensively reviewed the industrial effluent characteristics, integrating conventional technologies with MFCs for advanced resource recycling with a particular focus on the simultaneous bioelectricity generation and treatment of various industrial effluents. Finally, the article discussed the challenges, opportunities, and future perspectives for the large-scale applications of MFCs for sustainable industrial effluent management and energy recovery.

Polysorbate-80 pretreatment contributing to volatile fatty acids production associated microbial interactions via acidogenic fermentation of waste activated sludge

Polyoxyethylene dehydration sorbitol monooleate (polysorbate-80) pretreatment enhanced volatile fatty acids (VFAs) production of waste activated sludge (WAS) in acidogenic fermentation. The results showed that polysorbate-80 ameliorated WAS solubilization obviously with a soluble chemical oxygen demand (SCOD) increasing to 1536 mg/L within 4 h. Within 2 days of acidogenic fermentation, the maximal VFAs arrived to 2958.35 mg COD/L via polysorbate-80-pretreatment. The polysorbate-80 pretreatment boosted microbial diversity and richness in fermentation process. The Clostridium, Macellibacteroides and Acidocella strengthened microbial cooperation for the metabolic functions enhancement (e.g. amino acid metabolism and carbohydrate metabolism) for VFAs generation from WAS organics. Overall, the polysorbate-80 could play positive roles on the transformation of organic matter from sludge solid matters to VFAs, which was turned out to become an effective enhancing strategy for future WAS treatment / bioresource recovery with relatively low cost.

Microbial fuel cells for bioelectricity production from waste as sustainable prospect of future energy sector

Microbial fuel cell (MFC) is lauded for its potentials to solve both energy crisis and environmental pollution. Technologically, it offers the capability to harness electricity from the chemical energy stored in the organic substrate with no intermediate steps, thereby minimizes the entropic loss due to the inter-conversion of energy. The sciences underneath such MFCs include the electron and proton generation from the metabolic decomposition of the substrate by microbes at the anode, followed by the shuttling of these charges to cathode for electricity generation. While its promising prospects were mutually evinced in the past investigations, the upscaling of MFC in sustaining global energy demands and waste treatments is yet to be put into practice. In this context, the current review summarizes the important knowledge and applications of MFCs, concurrently identifies the technological bottlenecks that restricted its vast implementation. In addition, economic analysis was also performed to provide multiangle perspectives to readers. Succinctly, MFCs are mainly hindered by the slow metabolic kinetics, sluggish transfer of charged particles, and low economic competitiveness when compared to conventional technologies. From these hindering factors, insightful strategies for improved practicality of MFCs were formulated, with potential future research direction being identified too. With proper planning, we are delighted to see the industrialization of MFCs in the near future, which would benefit the entire human race with cleaner energy and the environment.

Performance evaluation of microbial fuel cell using a radiation synthesized low density polyethylene-grafted-poly (glycidyl methacrylate-co-vinyl acetate) as a proton exchange membrane

ABSTRACTThe present work focuses on the synthesis of a proton exchange membrane to be assembled in a microbial fuel cell (MFC) for simultaneous bioelectricity production and domestic wastewater treatment. The indigenous membrane was prepared by ionizing irradiation-induced graft copolymerization of glycidyl methacrylate (GMA) and vinyl acetate (VAc) onto low-density polyethylene and subsequently, the prepared grafted sheets were sulfonated via epoxy ring-opening of PGMA moieties. Parameters affecting the grafting degree were investigated and the prepared membranes were characterized by investigating their structural, thermal, mechanical, and electrical properties. Some physicochemical characteristics including ion exchange capacity, sulfonation density, and proton conductivity were also evaluated. The data confirmed the success of the preparation protocol to obtain a suitable membrane for the proposed application. Moreover, the performance of the assembled MFC was thoroughly investigated through the evaluation of its electrochemical behaviour including cyclic voltammetry, electrochemical impedance spectroscopy, columbic efficiency, and wastewater treatment capability. The sulfonated LDPE-g-P(GMA-co-VAc) membrane of 80% grafting degree shows substantial removal of chemical oxygen demand up to about 90% with columbic efficiency of 10.1%, columbic recovery of 8.7%, rate of energy harvest of 2.1 C/h and power density of 2.72 W m^-2. However, the use of 10 mM of KMnO₄ as electron acceptor drastically increase the harvested power density to reach 356.4 W m^-2.

Microbial profiles associated improving bioelectricity generation from sludge fermentation liquid via microbial fuel cells with adding fruit waste extracts

This first-attempt study illustrated the microbial cooperative interactions related to bioelectricity generation from the mixture of sludge fermentation liquid (SFL) and fruit waste extracts (FWEs) via microbial fuel cells (MFCs). The optimal output voltages of 0.65 V for SFL-MFCs, 0.51 V for FWEs-MFCs and 0.75 V for mixture-MFCs associated with bioelectricity conversion efficiencies of 1.061, 0.718 and 1.391 kWh/kg COD were reached, respectively. FWEs addition for substrates C/N ratio optimization contributed considerably to increase SFL-fed MFCs performance via triggering a higher microbial diversity, larger relatively abundance of functional genes and microbial synergistic interactions with genera enrichment of Clostridium, Alicycliphilus, Thermomonas, Geobacter, Paludibaculum, Pseudomonas, Taibaiella and Comamonas. Furthermore, a conceptual illustration of co-locating scenario of wastewater treatment plant(s), waste sludge in situ acidogenic fermentation, fruit waste collection/crushing station and MFC plant was proposed for the first time, which provided new thinking for future waste sludge treatment toward maximizing solid reduction and power recovery.

Augmentation of microbial fuel cell and photocatalytic polishing technique for the treatment of hazardous dimethyl phthalate containing wastewater

In the present paper, the potentiality of integrating microbial fuel cells (MFCs) with a photocatalytic reactor to maximize the wastewater treatment efficiency with concurrent power generation was explored. Dimethyl phthalate (DMP) and acetic acid (AA) were the employed substrate and the co-substrate, respectively, using Pseudomonas aeruginosa as a biocatalyst. MFCs operated by single substrate showed the maximum power generation of 0.75-3.84 W m^-3 whereas an addition of AA as the co-substrate yielded 3-12 fold higher power generation. Pseudomonas aeruginosa produced phenazine-1-carboxylic acid in DMP-fed MFC as the metabolite whereas AA along with DMP yielded pyocyanin which reduced the charge transfer resistance. Chemical oxygen demand (COD) removal efficiency in the MFCs was circa 62% after 11 days of operation. Thereafter, it further increased albeit with a drastic reduction in power generation. Subsequently, the MFC anolyte was treated in a photocatalytic reactor under visible light irradiation and catalyzed by CuO-gC₃N₄. The performance of photocatalytic reactor was evaluated, with COD and total organic carbon (TOC) removal efficiency of 88% and 86% after 200 min of light irradiation. The present work suggests that the MFC can be integrated with photocatalysis as a sustainable wastewater treatment method with concurrent power generation.

Effect of Fe3+ on the sludge properties and microbial community structure in a lab-scale A2O process

During biological wastewater treatment, ferric salt (Fe³⁺) usually serves as an inorganic flocculant to improve the agglomeration and sedimentation of suspended solids, and thus the removal efficiency of pollutants to meet the increasing strictly regulated wastewater discharge standards. In this study, we investigated the effects of Fe³⁺ on the removal efficiencies of pollutants, sludge properties, dominant flora and metabolic pathways of bacterial community in a classical anaerobic-anoxic-oxic (A²O) process. The results showed that a Fe³⁺ concentration lower than 10 mg·L^-1 could improve the removal efficiencies of chemical oxygen demand (COD) and total nitrogen (TN), while an inhibition effect was exerted at concentration higher than 10 mg·L^-1. The maximum removal efficiencies of COD and TN were 97% and 89%, respectively, under the critical Fe³⁺ concentration of 10 mg·L^-1. Total phosphorous (TP) removal was constantly positively correlated with Fe³⁺ concentration, due to the enhanced adsorption of phosphorus on activated sludge with the increase of surface roughness. Thauera displayed the highest relative abundance, and certain bacteria in Proteobacteria, Dehloromonas and Candidatus-Competibacter exhibited good adaptability to high concentration of Fe³⁺. In the context of metabolic collaterals, the most abundant functional gene families were identified to be Carbohydrate Metabolism, Amino Acid Metabolism, Cell Motility, Membrane Transport, and Replication and Repair. This study provides an extensive mechanistic insight into the impact of Fe³⁺ on the A²O process, which is of fundamental significance to exploit the contributions of inorganic salts to biological wastewater treatment.

Characterization of a new electrochemically active bacterium phylogenetically related to Alicyclobacillus hesperidum and its electrochemical performance in microbial fuel cell

Extremophilic microorganisms in microbial electrochemical systems have opened new possibilities for waste treatment. Here, a phenomenon of electricity generation under acidophilic condition was found in organic acid fermentation wastewater treatment using microbial fuel cell (MFC). The anodic microbial community analysis showed that the percentage of Firmicutes was 99.03%, which accounted for the vast majority of the microbial community at the late discharge stage with pH 3.0. As the dominant bacterium of Firmicutes, Alicyclobacillus hesperidum EG was isolated and identified. MFC experiments confirmed that Alicyclobacillus hesperidum EG exhibited good electricity generating capability with a maximum power density of 188.1 mW m^-2 at 50 °C and low pH. It is the first time that Alicyclobacillus hesperidum EG was discovered as a newly electrochemically active bacterium. Additionally, the morphological analysis combined with electrochemical experiments demonstrated that no nanowires were found in the anodic biofilm of Alicyclobacillus hesperidum EG, and Alicyclobacillus hesperidum EG may produce soluble redox-active small molecules as electron shuttles to facilitate extracellular electron transfer. Based on unique characteristics such as good acid resistance, high temperature resistance, and high electricity generation ability, Alicyclobacillus hesperidum EG exhibited great potential in wastewater treatment and energy recovery.

Advanced microbial fuel cell for waste water treatment-a review

Petroleum, coal, and natural gas reservoir were depleting continuously due to an increase in industrialization, which enforced study to identify alternative sources. The next option is the renewable resources which are most important for energy purpose coupled with environmental problem reduction. Microbial fuel cells (MFCs) have become a promising approach to generate cleaner and more sustainable electrical energy. The involvement of various disciplines had been contributing to enhancing the performance of the MFCs. This review covers the performance of MFC along with different wastewater as a substrate in terms of treatment efficiencies as well as for energy generation. Apart from this, effect of various parameters and use of different nanomaterials for performance of MFC were also studied. From the current study, it proves that the use of microbial fuel cell along with the use of nanomaterials could be the waste and energy-related problem-solving approach. MFC could be better in performances based on optimized process parameters for handling any wastewater from industrial process.

An overview of microbial fuel cell usage in wastewater treatment, resource recovery and energy production

Wastewater treatment is a high-cost and energy-intensive process not only due to large amounts of pollutants but also for the large volumes of water to be treated, which are mainly generated by human activities and different industries. In this regard, biological wastewater treatments have become substitutes to the current technologies, owing to the improved treatment efficiency and added value. Microbial fuel cells (MFCs) as one of the promising biological treatments have arisen as a viable solution for chemical oxygen demand (COD) removal and electricity generation simultaneously. Therefore, in this article, the effects of various operating conditions on the COD removal and power production from MFCs are thoroughly discussed. In addition, the advantages and weaknesses of current MFCs technologies used for different types of wastewater are summarized. Finally, the technical barriers facing by MFCs operation and the economic feasibility of using MFCs for wastewater treatment are provided.

Linking microbial mechanism with bioelectricity production in sludge matrix-fed microbial fuel cells: Freezing/thawing liquid versus fermentation liquor

This first-attempt study elucidated the microbial mechanism associated with bioelectricity output in microbial fuel cells (MFCs) fed with sludge matrices of freezing/thawing (F/T) liquid versus fermentation liquor, while a novel schematic elucidation for exploring cooperative interactions in anodic microbial consortia of MFCs supplied with such two feeds toward electrogenesis was put forward. Moreover, the F/T liquid cultivated main genera of Azospira, Povalibacter, Thauera, Terrimonas, Alicycliphilus, Dokdonella and Simplicispira for dual organics degradation and electrogenesis with power density of 0.152 mW/m² and electrogenesis efficiency of 1.152 kWh/kg COD, while the fermentation liquor fostered higher diversity and medium evenness with the enrichment of Phenylobacterium, Cellulomonas, Edaphobacter, Burkholderia, Clostridium, Sphingomonas, Leifsonia and Microbacterium in anodic biofilm and causing larger power density of 0.182 mW/m² and 1.418 kWh/kg COD-electrogenesis efficiency. Comparative analysis results indicated that the anodic fermentative bacteria exert considerable influence on concurrent organics degradation and electricity production through the synergistic interactions with exoelectrogens toward stable running of MFCs. Besides, the higher anodic microbial diversity, relatively middling community evenness and larger abundance of functional genes associated with electrogenesis together played contributive roles on more power generation through MFCs for treating WAS matrix. This study was conducive to bring about some new microbial mechanism understanding on maximizing bioenergy recovery via MFCs in future sludge management.

Insights into microbial community in microbial fuel cells simultaneously treating sulfide and nitrate under external resistance

The effect of electricity, induced by external resistance, on microbial community performance is investigated in Microbial Fuel Cells (MFCs) involved in simultaneous biotransformation of sulfide and nitrate. In the experiment, three MFCs were operated under different external resistances (100 Ω, 1000 Ω and 10,000 Ω), while one MFC was operated with open circuit as control. All MFCs demonstrate good capacity for simultaneous sulfide and nitrate biotransformation regardless of external resistance. MFCs present similar voltage profile; however, the output voltage has positive relationship with external resistance, and the MFC1 with lowest external resistance (100 Ω) generated highest power density. High-throughput sequencing confirms that taxonomic distribution of suspended sludge in anode chamber encompass phylum level to genus level, while the results of principal component analysis (PCA) suggest that microbial communities are varied with external resistance, which external resistance caused the change of electricity generation and substrate removal at the same, and then leads to the change of microbial communities. However, based on Pearson correlation analyses, no strong correlation is evident between community diversity indices (ACE index, Chao index, Shannon index and Simpson index) and the electricity (final voltage and current density). It is inferred that the performance of electricity did not significantly affect the diversity of microbial communities in MFCs biotransforming sulfide and nitrate simultaneously.

Insights into microbial interaction profiles contributing to volatile fatty acids production via acidogenic fermentation of waste activated sludge assisted by calcium oxide pretreatment

This first-attempted study illustrated the calcium oxide (CaO) agentia-pretreatment for prompting waste activated sludge (WAS) solubilization and enhancing volatile fatty acids (VFAs) bio-production through acidogenic fermentation. The 15-h CaO pretreatment was capable to produce a soluble chemical oxygen demand (SCOD) yield of ca. 153.17 mg COD/g VS and VFAs generation efficiency of 327.8 mg COD/g VS with adding dosage of 0.07 g/g TS. The relative frequencies corresponded to metabolic functions profiling were promoted obviously by CaO pretreatment and contributed to biosolid decomposition/VFAs production in sludge fermentation. Main genera of Azonexus, Arcobacter, Acinetobacter, Thauera, Petrimonas, Clostrium and Macellibacteroides cooperated synergically toward triggering concurrent VFAs generation/biosolid biodegradation. Finally, the CaO-pretreatment displayed positive merits in terms of sludge biosolid decomposition/recoverable resource harvest as compared with other alkali pretreatments. This study might shed lights on enriching intensification strategy for WAS management toward high-efficiency of recoverable resource harvest with lower cost.

Effect of heterotrophic anodic denitrification on anolyte pH control and bioelectricity generation enhancement of bufferless microbial fuel cells

Heterotrophic anodic denitrification (HAD) in the single-chamber microbial fuel cell (MFC) is a promising nitrogen removal technology. In this paper, the benefit (anolyte pH increase) and challenge (substrate consumption) brought by the heterotrophic anodic denitrification process for the electricity generation of bufferless MFCs were studied for the first time. Substrate anaerobic hydrolysis dramatically decreased the anolyte pH to 5.1, which seriously restricted the electric power output of the Control. The anolyte pH of the heterotrophic anodic denitrification MFCs (HADMFCs) with 60 mg/L (HADMFC-60), 90 mg/L (HADMFC-90), and 120 mg/L (HADMFC-120) nitrate nitrogen (NO₃^--N), retained above 6.0, 6.5, and 6.8 in every running cycles, due to the protons (H⁺) consumption by nitrate reduction. In the HADMFC-60 and HADMFC-90, 17.6% and 26.1% of the total organic carbons (TOC) were used for the nitrate reduction, but their electric power output significantly increased. The maximum power densities of the HADMFC-60 and HADMFC-90 were 3.3 and 5.4 times higher than that of the Control. However, when the proportion of TOC consumption for nitrate reduction increased to 35.8%, substrate insufficiency became a serious limitation for the electricity generation. The P_max of the HADMFC-120 dramatically decreased to 17.3 mW/m². Dysgonomonas was the dominant electro-active genus, and Petrimonas, Acidovorax and Devosia appeared as the denitrifying bacteria genera.

Different refractory organic substances degradation and microbial community shift in the single-chamber bio-photoelectrochemical system

The single-chamber bio-photoelectrochemical system (BPES) with a BiOBr photocathode was developed for acid orange 7 (AO7), 2,4 dichlorophenol (2,4-DCP) and chloramphenicol (CAP) degradation under solar irradiation. Photoelectrochemical characterizations showed that the optimized BiOBr-photocathode exhibited great light-response property and excellent electrochemcial performance. Moreover, desired TOC removals were achieved for various organic pollutants, with the values of 90.97% (AO7), 81.41% (2,4-DCP) and 78.47% (CAP). Besides, the lower cathode potentials in the illuminated BPESs were favorable to efficient pollutants degradation. Significant microbial community shifts were observed among the inoculation and anodic biofilms from the BPES, and the most dominated species in anodic biofilms acclimated to various pollutants were Geobacter and Pseudomonas, which have the abilities of extracellular electrons transfer and organics degradation. Some other species that different from the inoculation were also identified from the BPES biofilms. This study suggested that BPES had great potential for refractory organics degradation.

Characteristics of Biohydrogen Production and Performance of Hydrogen-Producing Acetogen by Increasing Normal Molasses Wastewater Proportion in Anaerobic Baffled Reactor

The biohydrogen production efficiency and performance of hydrogen-producing acetogen in a four-compartment anaerobic baffled reactor (ABR) were studied by gradually increasing the influent normal molasses wastewater (NMWW) proportion. When the influent NMWW proportion increased to 55%, ABR could develop microbial community with methanogenic function in 63 days and reach a stable operation. When the influent NMWW proportion increased to 80% and reached a stable state, ethanol fermentation was established from butyric acid fermentation in the first three compartments, whereas butyric acid fermentation in the fourth compartment was strengthened. The average biohydrogen production yield and biohydrogen production capacity by COD removal increased to as high as 12.85 L/day and 360.22 L/kg COD when the influent NMWW proportion increased from 55% to 80%, respectively. Although the biogas yield and the specific biogas production rate reached 61.54 L/day and 232 L/kg MLVSS·day, the biohydrogen production yield and specific biohydrogen production rate were only 12.85 L/day and 48 L/kg MLVSS·day, which results in hydrogen consumption by homoacetogenesis and methanogenesis.

Treatment of isopropanol wastewater in an anaerobic fluidized bed microbial fuel cell filled with macroporous adsorptive resin as multifunctional biocarrier

The isopropanol (IPA) wastewater was treated in an anaerobic fluidized bed microbial fuel cell (AFB-MFC) filled with macroporous adsorptive resin (MAR) particles as multifunctional biocarrier. MAR was used as a biological carriers and adsorbent. MAR was characterized by scanning electron microscope. The diffusion of isopropanol in MAR was studied by Materials Studio (MS) software, and diffusion coefficients were analyzed and calculated by molecular dynamics simulation. The simulation results were qualitatively consistent with the available experimental data. The diffusivity of IPA in MAR increased firstly, with the increasing IPA weight, and then decreased. The maximum diffusivity was resulted to be 0.3722 Å²/ps. In addition, the response surface methodology (RSM) and Box-Behnken design were used to study the effects of initial IPA concentration, flow rate and external resistance on performance of power output and pollutant degradation. The optimal experimental condition was observed as initial IPA concentration of 483.49 mg/L, a flow rate of 57.70 mL/min, and external resistance of 5225.78 Ω. After 21 h of operation under the optimized conditions, the maximum power density was 135.73 ± 0.17 mW/m² and the COD removal was 68.21 ± 0.24%, which increased by 65.85% and 9.29%, respectively.

A microbial fuel cell system with manganese dioxide/titanium dioxide/graphitic carbon nitride coated granular activated carbon cathode successfully treated organic acids industrial wastewater with residual nitric acid

To meet the urgent demands for sustainable and efficient, environmental-friendly wastewater treatment, a Microbial fuel cell reactor system with MnO₂/TiO₂/g-C₃N₄ (manganese dioxide/ titanium dioxide/graphitic carbon nitride) @GAC (granular activated carbon) electrode was developed. It was both efficient and energy-saving in treating organic acid wastewater generated in Nylon production, with high-concentration COD and residual nitric acid. The MnO₂/TiO₂/g-C₃N₄ catalyst was deposited on GAC via in-situ growth and sol-gel method. The COD, NH₄⁺-N and NO₃^--N was efficiently removed (respectively 98%, 99% and 99%). The COD removal capacity (17.77 kg COD m^-3d^-1) and the maximum power density (1176.47 mW m^-3) was respectively 36.83% and 65.29% higher than the GAC cathode system. The anodic and cathodic microbial consortiums in MFC were analyzed and compared. The MnO₂/TiO₂/g-C₃N₄@GAC MFC system is technically feasible and cost-effective in treating industrial wastewater.

Influence of wastewater microbial community on the performance of miniaturized microbial fuel cell biosensor

Microbial fuel cells (MFCs) based sensors had been studied in measuring biochemical oxygen demand (BOD) or the equivalent chemical oxygen demand (COD) recently. Limited attention has been paid to the effect of the microbial communities in wastewater on the responses of these sensors. This study systematically evaluated, for the first time, the effect of wastewater samples from a variety of sources on the electrical response of a micro-fabricated double-chamber MFC device. It was found that the response of the MFC is positively correlated with the bacterial composition, in particular electroactive bacteria. The presence of aerobic bacteria in the sample reduces the current generation. These findings indicated that the bacterial content of the water sample could be a significant interference source and must be considered in the use of µMFC-based sensors. Filtering samples may be effective in improving the reliability of these microsensors.

Application of slow-release carbon sources embedded in polymer for stable and extended power generation in microbial fuel cells

Stable and long-term power output is a prerequisite for the application of the energy recovered from microbial fuel cells (MFCs). In this study, a novel fuel supplying strategy based on slow-release carbon embedded in polymer gels was attempted in MFCs aimed to achieve a sustainable power generation. Polymer gels containing starch acetate as the carbon source (40% (w/w)) were prepared, and the effects of its loading dosage on power generation and microbial community structure were investigated. Results showed that the MFCs once fed with 20.0 g/L, 37.5 g/L and 55.0 g/L polymer gels attained a long-term power generation periods of 110, 140 and 170 days, respectively, with a maximum power density of 386-427 mW/m². The MFC with a medium loading dosage (37.5 g/L polymer gels) performed best. MFCs fed with the slow-release carbon enriched a distinct microbial community comparing to the control MFC with acetate as the carbon source, with the genera Geobacter, Sphaerochaeta, Christensenellaceae, Aminiphilus and Proteiniphilum significantly enriched on the anode electrode, and Sphaerochaeta, Proteiniphilum and Bacteroidetes in the anolyte. This carbon source providing method will promote the application of MFCs as a sustainable and stable power source for environmental monitoring and remediation.

Enhancing biofilm formation in biofilters for benzene, toluene, ethylbenzene, and xylene removal by modifying the packing material surface

Polyurethane (PU) sponges are popular packing material in biofilters and their smooth and hydrophobic surface often leads to an uneven distribution and detachment of biofilms. In this work, the surface of PU sponge was modified to obtain higher roughness and positive charge. The performances of two biofilters (BF1 with pristine sponge and BF2 with modified sponge) for benzene, toluene, ethylbenzene, and xylene (BTEX) removal were investigated. Total Volatile Organic Compound (TVOC) removal efficiency and CO₂ increment were 61% and 804 ppm for BF2 respectively after start-up, compared with 51% and 538 ppm for BF1. Analysis on biofilms showed that the modification of PU sponge significantly improved the microbial growth, viability and adhesive strength in biofilms, reduced extracellular polymeric substance (EPS) and changed the microbial community. These results demonstrate that modified sponge can enhance biofilm formation and BTEX removal in biofilters and may applied in large-scale applications.

Microbial fuel cell for nutrient recovery and electricity generation from municipal wastewater under different ammonium concentrations

In the present study, a dual-compartment microbial fuel cell (MFC) was constructed and continuously operated under different influent concentrations of ammonium-nitrogen (5-40 mg/L). The impacts of ammonium on organics removal, energy output and nutrient recovery were investigated. Experimental results demonstrated that this MFC reactor achieved a CDO removal efficiency of greater than 85%. Moreover, excess ammonium concentration in the feed solution compromises the generation of electricity. Simultaneously, the recovery rate of phosphate achieved in the MFC was insignificantly influenced at the wider influent ammonium concentration. In contrast, a high concentration of ammonium may not be beneficial for its recovery.