Hydrochloric acid-modified fungi-microalgae biochar for adsorption of tetracycline hydrochloride: Performance and mechanism

A lead-free red fluorescent cesium rubidium europium perovskite for the detection of tetracycline by antenna effect

Metal halide perovskite based on caesium and lead has excellent photoelectric properties, but the toxicity of lead in perovskite structure limits its application in analytical chemistry. It is of great significance to develop lead-free perovskite. Herein, lead-free red fluorescent Cs2RbEuCl6 perovskite nanocrystals (PNCs) were synthesized in this paper. Cs2RbEuCl6 PNCs has the maximum emission peak at around 615 nm. Red fluorescence intensity of Cs2RbEuCl6 PNCs can be increased more than 10-fold by antenna effect between tetracycline hydrochloride and Cs2RbEuCl6 PNCs. Meanwhile, the fluorescence intensity of Cs2RbEuCl6 PNCs increased with the concentration of tetracycline hydrochloride (TCH). Further studies showed that the fluorescence enhancement rate (I/I0) of Cs2RbEuCl6 PNCs was linearly correlated with the concentration range of 5.0-60.0 μM TCH. This work provides a method to enhance the red fluorescence of lead-free perovskites by antenna effect, and also demonstrates that the antenna effect between small molecules and lead-free perovskites can be used for fluorescence-enhanced detection of small molecules.

Assessing the Performance of Different Treatment Methods in Removing Tetracycline from Wastewater: Efficiency and Cost Evaluation

To tackle the pollution of tetracycline (TC) in aqueous environments, a few treatment methods, including ozonation, adsorption, and photocatalytic degradation, were compared using a novel and sustainable granular activated carbon-based zinc oxide nanoparticle (ZnO@GAC) composite. The results demonstrate that the ZnO@GAC composite towards TC exhibited a high removal efficiency of 82.1% in a batch adsorption system. Moreover, the photocatalytic TC degradation study on ZnO@GAC under UV light yields a maximum degradation efficiency of 86.4% with a pseudo-first-order rate constant value of 0.0059 min-1. Ozonation treatment resulted in TC and total organic carbon (TOC) removal reaching a maximum of 95.3% and 79.7% for 4 mg O3/min and 99.6% and 86.6% for 16 mg O3/min after 10 min. Overall, in comparing the adsorption, photocatalysis, and ozonation techniques, in terms of removal efficiency and time, ozonation was found to be more promising for treating TC, while in terms of cost-effectiveness, the adsorption process is preferable. Finally, the application of the developed composite in municipal and hospital wastewater using adsorption, photocatalytic degradation, and ozonation techniques revealed that the TOC removal efficiencies were higher for hospital wastewater than municipal wastewater. Furthermore, the applicability of these techniques in treating hospital wastewater containing pharmaceuticals, antibiotics, fungicides, and antimicrobial pollutants shows an outstanding result after treatment. In conclusion, the technologies studied in this research can significantly improve the efficiency and effectiveness of wastewater treatment applications, providing a sustainable, cost-effective, and eco-friendly solution.

Waste cotton-based activated carbon with excellent adsorption performance towards dyes and antibiotics

A novel adsorbent is prepared from waste cotton fiber by a simple pyrolysis-activation process, and it can efficiently adsorb many kinds of organic pollutants (cationic/anionic dyes and antibiotics etc.). The obtained cotton-based activated carbon (CAC) with large specific surface area (3709 m2 g-1) and suitable pore structure provide abundant active sites and fast channels for the adsorption of pollutant molecules. Its saturated adsorption capacities towards methylene blue, Congo Red and tetracycline hydrochloride at room temperature can reach to 2331, 7265 and 1250 mg g-1, respectively. In addition, the optimal sample also exhibits excellent adsorption ability towards Rhodamine B (1327 mg g-1), methyl orange (955 mg g-1) and ciprofloxacin hydrochloride (824 mg g-1). The adsorption involves a multi-process including pore filling, Van der Waals force interaction, electrostatic attraction, hydrogen bond formation, surface complexation and π-π stacking etc. The CAC adsorbent also exhibits excellent resistance to environmental disturbances (pH, coexisting ions and multicomponent systems etc.) and good regeneration/recycling performance. This study develops a high-efficiency biomass-based adsorbent with excellent adsorption performance and application generality, which has great potential in wastewater treatment.

Microporous carbon derived from waste plastics for efficient adsorption of tetracycline: Adsorption mechanism and application potentials

In recent years, the accumulation of waste plastics and emergence plastic-derived pollutants such as microplastics have driven significantly the development and updating of waste plastic utilization technology. This study prepared the porous carbon (PC-1-KOH) material directly from polyethylene terephthalate (PET) in waste plastic bottles using KOH activation and molten salt strategy for efficient removal of antibiotic tetracycline (TC). The maximum removal efficiency of TC was 100.0% with a PC-1-KOH weight of 20 mg. In addition, the TC removal efficiency stayed over 80.0% within the rage of pH of 3-9 and different water bodies. The adsorption process was described by the Pseudo-second-order kinetic model and the Langmuir isotherm, suggesting that the adsorption of TC was predominantly chemical in nature and occurred on a homogeneous surface. The pores filling, hydrogen bonding, π-π stacking interactions and electrostatic interaction are the main mechanisms of TC adsorption. This work demonstrates a sustainable approach to converting plastic waste derived materials into functional materials for effective pollution removal and environmental remediation.

Preparation of ZnAl layered double hydroxides supported by silica for the treatment of Cr(VI) and Cu(II) in aqueous solution

A novel adsorbent ZnAl-LDHs/SiO2 (ZA/SiO2) was prepared by blending urea mixture of ZnSO4 and Al2(SO4)3 while using SiO2 as a support form. The adsorption properties of ZA/SiO2 for the removal of toxic metal ions (Cu(II) and Cr(VI)) from water were evaluated. By batch experiment method to investigate the ZA/SiO2 adsorption of Cu(II) and Cr(VI) solution treatment effect. The sorption kinetics curves of Cu(II) and Cr(VI) on ZA/SiO2 were L-shaped. What's more, the solid concentration effect was found in the process of sorption kinetics. Langmuir and Freundlich sorption isotherm models were used to analyze the adsorption data. The results showed that the adsorption conforms to Langmuir and Freundlich adsorption isotherm models. However, the adsorption capacity of ZA/SiO2 compounds for Cu(II) and Cr(VI) is greatly improved. The adsorption capacity of Cu(II) is 158 mg·g-1 and of Cr(VI) is 176 mg·g-1, which were 3.6 and 1.8 times of ZnAl-LDHs (ZA), respectively. Density functional theory (DFT) was utilized for the analysis of intrinsic mechanism and specific pathways. The primary mechanism for removing Cr(VI) from water mainly included the intercalation of Cr2O72- and exchange between Cr2O72- and OH-, excluding Cr(OH)3 precipitation. Regarding the primary mechanism for eliminating Cu(II) from water, it involves isomorphic substitution as the predominant process, except for the formation of Cu(OH)2 precipitates.

Cost-effective evaluation of modified ochre soil and its combination with cationic polyacrylamide for municipal wastewater sludge conditioning

One of the most costly stages of activated sludge wastewater treatment plants is the treatment and dewatering of waste sludge. Chemical conditioning of sludge, as one of the most widespread methods to enhance sludge dewaterability, accounts for a significant portion of operational expenses due to the consumption of expensive polymeric compounds. This research aims to assess the cost-effectiveness of ochre soil, modified with hydrochloric acid, as an affordable mineral for conditioning waste sludge in an activated sludge system. The optimal conditions for acid modifications are obtained using response surface methodology. Then, its performance is compared with conventional coagulants (ferric chloride and alum) and in combination with cationic polyacrylamide (CPAM). To assess the conditioning process efficiency, the specific resistance to filtration (SRF) parameter was employed. At an optimal dose of modified ochre soil (MOS) equal to 300 (mg/g dry solids), the SRF value decreased from 31.96 to 2.7 Tm/kg. The combination of 100 (mg/gDS) MOS with 0.5 (mg/gDS) CPAM showed as the most cost-effective among the coagulants tested, with a 31% greater SRF reduction compared to CPAM used alone. This study shows the practical efficacy of an eco-friendly natural mineral as a polymer alternative, with the potential for sludge dewatering.

Applicability analysis of algae biochar for anaerobic membrane bioreactors in wastewater treatment: A review from a sustainability assessment perspective

The incorporation of biochar can significantly enhance the performance of anaerobic membrane bioreactors (AnMBRs), achieving up to a 95 % increase in pollutant removal efficiency and an 86 % improvement in methane production. Algae biochar, in particular, shows great promise as an effective additive in AnMBR systems because of its low cost (approximately $0.470/kg) and the abundance of raw material sources. This paper presents a comprehensive applicability analysis of algae biochar-AnMBRs from a sustainability assessment perspective, addressing technical, environmental, economic, and social dimensions. Key technical benefits include a reduction in membrane fouling by 92.1 % and an enhancement of energy recovery by 58.7 % compared to conventional AnMBRs. Following this, the paper evaluates algae biochar-AnMBRs from environmental, economic, and social viewpoints to emphasize the practical applicability and potential of this process. Finally, this review addresses the limitations related to the full-scale implementation of this technology and proposes strategic approaches to overcome these challenges. Overall, the review provides valuable insights into the practical application of algae biochar-AnMBR systems, with a strong focus on sustainability.

Carboxymethyl cellulose assisted hydrothermal synthesis of litchi-like zinc ferrite nanoparticles for water remediation through visible photo-Fenton-like catalysis

The conventional methods for the synthesis of zinc ferrite (ZnFe2O4) basically require high temperature calcination oxidation step, which produces environmentally unfriendly high energy consumption and may produce harmful gases that pollute the atmosphere, as well as the calcination synthesis limits the application of ZnFe2O4 such as preparation of organic composite materials. To end this, by adding carboxymethyl cellulose (CMC) to the reaction system, homogeneous litchi-like ZnFe2O4/CMC nanoparticles were successfully synthesized without alkali and calcination in this paper. The rich carboxyl group of CMC is conducive to the chelation and fixation of metal ions in the reaction precursor, which greatly promotes the synthesis of ZnFe2O4. The synthesized particle size is ~100 nm, with obvious ZnFe2O4 diffraction peaks and good crystallinity. The photocatalytic performance of the synthesized photocatalyst was evaluated by visible light-Fenton-like method. With the activation of peroxymonosulfate (PMS), 80.27 % of tetracycline hydrochloride (TC) was degraded in just 18 min, suggesting that the synthesized catalyst had an excellent photocatalytic performance. After four cycles, the catalyst still could degrade 64.52 % TC. And the same behavior in XRD and FTIR spectra confirms the stability of the photocatalyst. In addition, it was determined that singlet oxygen (1O2) dominated the visible light catalytic degradation.

The Biochar Derived from Pecan Shells for the Removal of Congo Red: The Effects of Temperature and Heating Rate

Organic pollutants, especially dyes, are seriously hazardous to the aquatic system and humans due to their toxicity, and carcinogenic or mutagenic properties. In this study, a biochar prepared from agricultural waste (pecan shells) via pyrolysis was applied to remove the dye pollutant Congo Red from wastewater to avoid a negative effect to the ecosystem. This study also investigated the effect of preparation conditions (temperature and heating rate) on the physicochemical properties and the adsorption performance of biochars. The physicochemical properties of the biochar were characterized using scanning electron microscopy, X-ray powder diffraction, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. The adsorption performance of the biochar was evaluated for Congo Red removal. The results showed that biochar prepared at 800 °C with a heating rate of 20 °C/min (PSC-800-20) exhibited a higher specific surface area of 450.23 m2/g and a higher adsorption capacity for Congo Red (130.48 mg/g). Furthermore, adsorption experiments indicated that the pseudo-second-order and Langmuir models fitted well with the adsorption kinetics and isotherms of the biochar derived from pecan shells, respectively. Additionally, the PSC-800-20 biochar demonstrated a stable adsorption capacity over multiple cycles, suggesting its potential for regeneration and reuse in wastewater treatment applications. Therefore, the biochar derived from agricultural waste presents a promising and sustainable solution for the removal of toxic dye pollutants from wastewater.

Preparation of MgAl-LDHs loaded with blast furnace slag and its removal of Cu(II) and methylene blue from aqueous solution

Blast furnace slag (BFS) is a kind of waste produced in industrial production, as well as a valuable secondary resource. In this paper, layered double hydroxides composites (BFS/LDHs) were prepared by aqueous polymerization, with industrial waste BFS as modifier and magnesium nitrate, aluminium nitrate, and urea as raw materials. BFS/LDHs have been characterized by using scanning electron microscopy (SEM), fourier infrared spectrometer (FT IR), x-ray diffraction (XRD), and the specific surface area analyser (BET). The adsorption of BFS/LDHs on Cu (II) and methylene blue (MB) was investigated by batch experiments. The results showed that the adsorption capacity of BFS/LDHs to Cu (II) is stronger than that of MB. What's more, the solid concentration effect was found in the process of sorption kinetics and sorption isotherms. The sorption kinetics curves of Cu (II) and MB on BFS/LDHs were well fitted by the quasi-second-order kinetics under different adsorbent concentrations. Langmuir and Freundlich sorption isotherm models were used to analyse the adsorption. It showed that the adsorption conforms to Langmuir and Freundlich's adsorption isotherm models. The BFS/LDHs composites have good recycling availability in this adsorption process of Cu (II) and MB, the removal capacity of which was reduced by 16.1% and 3.8% after being recycled for six times, respectively. More importantly, BFS/LDHs composites are not only expected to become a sewage treatment agent, but also to solve the problem of industrial waste treatment, which is a win-win strategy.

Biochar Composite with Enhanced Performance Prepared Through Microbial Modification for Water Pollutant Removal

This study developed mycelial biochar composites, BQH-AN and BQH-MV, with stable physicochemical properties and significantly improved adsorption capabilities through microbial modification. The results showed that the specific surface area and porosity of BQH-AN (3547.47 m2 g-1 and 2.37 cm3 g-1) and BQH-MV (3205.59 m2 g-1 and 2.46 cm3 g-1) were significantly higher than those of biochar BQH (2641.31 m2 g-1 and 1.81 cm3 g-1), which was produced without microbial treatment. In adsorption experiments using rhodamine B (RhB), tetracycline hydrochloride (TC), and Cr (VI), BQH-AN showed maximum adsorption capacities of 1450.79 mg g-1 for RhB, 1608.43 mg g-1 for TC, and 744.15 mg g-1 for Cr(VI). BQH-MV showed similarly strong performance, with 1329.85 mg g-1 for RhB, 1526.46 mg g-1 for TC, and 752.27 mg g-1 for Cr(VI). These values were not only higher than those of BQH but also outperformed most other biochar adsorbents. Additionally, after five reuse cycles, the pollutant removal efficiency of the mycelial biochar composites remained above 69%, demonstrating excellent regenerative ability. This study not only produced biochar with superior adsorption properties but also highlighted microbial modification as an effective way to enhance lignocellulosic biochar performance, paving the way for further biomass development.

Mycelium-Doped Straw Biochars for Antibiotic Control

Straw, a predominant agricultural residue, represents a significant waste product. Harnessing its potential is of paramount importance both in terms of research and economic value. In this study, chemically pretreated corn straw was infused with distinct microbial fungal mycelium variants and subsequently transformed into a series of biochars through a process involving carbonization and activation. The findings revealed enhancements in the specific surface area and total pore volume of mycelium-doped straw biochars compared to the original corn straw biochar (BCS). Additionally, discernible disparities were observed in their physical and chemical attributes, encompassing functional groups, surface chemistry, and micro-morphology. Notably, in water-based antibiotic removal experiments focusing on tetracycline hydrochloride (TH) and chloramphenicol (CP), the mycelium-doped straw biochars outperformed BCS. Their maximum adsorption capacities for TH and CP surpassed those of alternative adsorbents, including other biochars. Impressively, even after five cycles, the biochar exhibited a removal rate exceeding 80%, attesting to its robust stability. This study successfully emphasized the efficacy of incorporating fungal mycelium to enhance the adsorption properties of straw-based biochar, introducing a new theoretical basis for the development of lignocellulosic materials.

Exploring the biosorption of nickel and lead by Fusarium sp. biomass: kinetic, isotherm, and thermodynamic assessment

Fungal biomass is as a cost-effective and sustainable biosorbent utilized in both active and inactive forms. This study investigated the efficacy of inactivated and dried biomass of Fusarium sp. in adsorbing Ni2+ and Pb2+ from aqueous solutions. The strain underwent sequential cultivation and was recovered by filtration. Then, the biomass was dried in an oven at 80 ± 2 °C and sieved using a 0.1-cm mesh. The biosorbent was thoroughly characterized, including BET surface area analysis, morphology examination (SEM), chemical composition (XRF and FT-IR), thermal behavior (TGA), and surface charge determination (pH-PZC and zeta potential). The biosorption mechanism was elucidated by fitting equilibrium models of kinetics, isotherm, and thermodynamic to the data. The biosorbent exhibited a neutral charge, a rough surface, a relatively modest surface area, appropriate functional groups for adsorption, and thermal stability above 200 °C. Optimal biosorption was achieved at 25 ± 2 °C, using 0.05 g of adsorbent per 50 mL of metallic ion solution at initial concentrations ranging from 0.5 to 2.0 mg L-1 and at pH 4.5 for Pb2+ and Ni2+. Biosorption equilibrium was achieved after 240 min for Ni2+ and 1440 min for Pb2+. The process was spontaneous, mainly through chemisorption, in monolayer for Ni2+ and multilayer for Pb2+, with efficiencies of over 85% for both metallic ion removal. These findings underscore the potential of inactive and dry Fusarium sp. biomass (IDFB) as a promising material for the biosorption of Ni2+ and Pb2+.

Enhanced Tetracycline Adsorption Using KOH-Modified Biochar Derived from Waste Activated Sludge in Aqueous Solutions

Antibiotic pollution poses a serious environmental concern worldwide, posing risks to ecosystems and human well-being. Transforming waste activated sludge into adsorbents for antibiotic removal aligns with the concept of utilizing waste to treat waste. However, the adsorption efficiency of these adsorbents is currently limited. This study identified KOH modification as the most effective method for enhancing tetracycline (TC) adsorption by sludge biochar through a comparative analysis of acid, alkali, and oxidant modifications. The adsorption characteristics of TC upon unmodified sludge biochar (BC) as well as KOH-modified sludge biochar (BC-KOH) were investigated in terms of equilibrium, kinetics, and thermodynamics. BC-KOH exhibited higher porosity, greater specific surface area, and increased abundance of oxygen-based functional groups compared to BC. The TC adsorption on BC-KOH conformed the Elovich and Langmuir models, with a maximum adsorption capacity of 243.3 mg/g at 298 K. The adsorption mechanisms included ion exchange, hydrogen bonding, pore filling, and electrostatic adsorption, as well as π-π interactions. Interference with TC adsorption on BC-KOH was observed with HCO3-, PO43-, Ca2+, and Mg2+, whereas Cl-, NO3-, and SO42- ions exhibited minimal impact on the adsorption process. Following three cycles of utilization, there was a slight 5.94% reduction in the equilibrium adsorption capacity, yet the adsorption capacity remained 4.5 times greater than that of unmodified sludge BC, underscoring its significant potential for practical applications. This research provided new insights to the production and application of sludge biochar for treating antibiotic-contaminated wastewater.

One-Pot Preparation of Layered Double Hydroxide-Engineered Boric Acid Root and Application in Wastewater

Heavy metals and organic pollutants are prevalent in water bodies, causing great damage to the environment and human beings. Hence, it is urgent to develop a kind of adsorbent with good performance. Anion interlacing layered double hydroxides (LDHs) are a promising adsorbent for the sustainable removal of heavy metal ions and dyes from wastewater. Using aluminum chloride, zinc chloride and ammonium pentaborate tetrahydrate (NH4B5O8 · 4H2O, BA) as raw materials, the LDHs complex (BA-LDHs) of B5O8- intercalation was prepared by one-step hydrothermal method. The BA-LDHs samples were characterized by a X-ray powder diffractometer (XRD), scanning electron microscope (SEM), Fourier transform infrared spectrometer (FT-IR) and the Brunauer-Emmett-Teller (BET) method. The results showed that B5O8- was successfully intercalated. Adsorption experimental results suggested that BA-LDHs possess a maximum adsorption capacity of 18.7, 57.5, 70.2, and 3.12 mg·g-1 for Cd(II), Cu(II), Cr(VI) and Methylene blue (MB) at Cs = 2 g·L-1, respectively. The adsorption experiment conforms to the Langmuir and Freundlich adsorption models, and the kinetic adsorption data are well fitted by the pseudo-second-order adsorption kinetic equation. The as-prepared BA-LDHs have potential application prospects in the removal of heavy metals and dyes in wastewater. More importantly, they also provide a strategy for preparing selective adsorbents.

Adsorptive removal of perfluorooctanoic acid from aqueous matrices using peanut husk-derived magnetic biochar: Statistical and artificial intelligence approaches, kinetics, isotherm, and thermodynamics

Removal of perfluorooctanoic acid (PFOA) from water matrices is crucial owing to its pervasiveness and adverse ecological and human health effects. This study investigates the adsorptive removal of PFOA using magnetic biochar (MBC) derived from FeCl3-treated peanut husk at different temperatures (300, 600, and 900 °C). Preliminary experiments demonstrated that MBC600 exhibited superior performance, with its characterization confirming the presence of γ-Fe2O3. However, efficient PFOA removal from water matrices depends on determining the optimum combination of inputs in the treatment approaches. Therefore, optimization and predictive modeling of the PFOA adsorption were investigated using the response surface methodology (RSM) and the artificial intelligence (AI) models, respectively. The central composite design (CCD) of RSM was employed as the design matrix. Further, three AI models, viz. artificial neural network (ANN), support vector machine (SVM), and adaptive neuro-fuzzy inference system (ANFIS) were selected to predict PFOA adsorption. The RSM-CCD model applied to optimize three input process parameters, namely, adsorbent dose (100-400 mg/L), pH (3-10), and contact time (20-60 min), showed a statistically significant (p < 0.05) effect on PFOA removal. Maximum PFOA removal of about 98.3% was attained at the optimized conditions: adsorbent dose: 400 mg/L, pH: 3.4, and contact time: 60 min. Non-linear analysis showed PFOA adsorption was best fitted by pseudo-second-order kinetics (R2 = 0.9997). PFOA adsorption followed Freundlich isotherm (R2 = 0.9951) with a maximum adsorption capacity of ∼307 mg/g. Thermodynamics and spectroscopic analyses revealed that PFOA adsorption is a spontaneous, exothermic, and physical phenomenon, with electrostatic interaction, hydrophobic interaction, and hydrogen bonding governing the process. A comparative analysis of the statistical and AI models for PFOA adsorption demonstrated high R2 (>0.99) for RSM-CCD, ANN, and ANFIS. This research demonstrates the applicability of the statistical and AI models for efficient prediction of PFOA adsorption from water matrices using MBC (MBC600).

Magnetization and ZIF-67 modification of Aspergillus flavus biomass for tetracycline removal from aqueous solutions: A stable and efficient composite

In the present work, the biomass of Aspergillus flavus (AF) was modified using magnetic nanoparticles MnFe2O4 and metal-organic framework of ZIF-67, and its ability to remove tetracycline antibiotic (TCH) was investigated. With the help of physicochemical tests, AF biomass modification with ZIF-67 and MnFe2O4 magnetic nanoparticles was confirmed. Based on the BET value, AF-MnFe2O4-ZIF-67 (139.83 m2/g) has a higher surface value than AF (0.786 m2/g) and AF/MnFe2O4 (17.504 m2/g). Also, the magnetic saturation value revealed that the modified biomass can be isolated from the treated solution using a simple magnetic field. Maximum TCH elimination (99.04%) using AF-MnFe2O4-ZIF-67 was obtained at pH 7, adsorber mass of 1 g/L, adsorption time of 40 min, and TCH content of 10 mg/L. The thermodynamic study indicated that the TCH abatement using the desired composite is spontaneous and exothermic. The experimental results showed that the adsorption process is compatible with the pseudo-second-order kinetic and Freundlich model. The maximum adsorption capacity for AF, AF-MnFe2O4, and AF-MnFe2O4-ZIF-67 was quantified to be 9.75 mg/g, 25.59 mg/g, and 43.87 mg/g, respectively. The reusability of the desired adsorbers was examined in up to 8 steps. The outcomes showed that the adsorbers can be used several times in TCH elimination. The provided composite can remove TCH from hospital wastewater, so it can be suggested for use in water and wastewater treatment works.

Round-the-Clock Adsorption-Degradation of Tetracycline Hydrochloride by Ag/Ni-TiO2

The synergy of adsorption and photocatalysis is a good method to remove organic pollutants in wastewater. In recent decades, persistent photocatalysis has gained considerable interest for its ability to sustain the catalytic degradation of organic pollutants in the dark. Herein, we report three different TiO2 nanomaterials to remove tetracycline hydrochloride (TCH) in solution. We found that the removal ability of TiO2, Ni-TiO2, and Ag/Ni-TiO2 is 8.8 mg/g, 13.9 mg/g and 23.4 mg/g, respectively, when the initial concentration of TCH is 50 mg/L. Chemical adsorption could be the rate-determining step in the TCH adsorption process. Moreover, Ag nanoparticles dispersed on Ni doped TiO2 surface act as traps to capture photo-generated electrons upon illumination with indoor light. The holes in Ag/Ni-TiO2 serve as critical oxidative species in TCH degradation under dark conditions. This work provides new insights into the design of persistent photocatalysts that can be activated by weak illumination and degrade organic pollutants in wastewater after sunset.

Combination of co-pyrolyzed biomass-sludge biochar and ultrasound for persulfate activation in antibiotic degradation: efficiency, synergistic effect, and reaction mechanism

A carbon material Cu-corn straw-sludge biochar (Cu-CSBC) was prepared by hydrothermally modifying sewage sludge and corn stover. The composite coupled to ultrasound can effectively catalyze the activation of PS for organic pollutants degradation, and the removal rate of 20 mg/L TC reached 89.15% in 5 min in the presence of 0.5 g/L Cu-CSBC and 3 mM PS. The synergistic effect between the factors in the system, the reaction mechanism, and the efficient removal of TC in the aqueous environment were explored in a Cu-CSBC/US/PS system established for that purpose. Quenching experiments and electron paramagnetic resonance analysis both demonstrated the Cu-CSBC/US/PS system generated •OH, SO4-•, 1O2, and O2- •, which involved in the reaction. The Cu, carboxyl, and hydroxyl groups on the Cu-CSBC surface promoted the generation of radicals and non-radicals for the degradation process, which was dominated by both radical and non-radical pathways. The degradation pathway is proposed by measuring the intermediate products with LC-MS. Finally, the stability of the Cu-CSBC/US/PS system was tested under various reaction conditions. This study not only prepared a novel biochar composite material for the active degradation of organic pollutants by PS but also provided an effective method for the resource utilization of solid waste and sludge treatment.

Remediation of arsenic and fluoride from groundwater: a critical review on bioadsorption, mechanism, future application, and challenges for water purification

In the past few decades, the excessive and inadequate use of technological advances has led to groundwater contamination, mainly caused by organic and inorganic pollutants, which are highly harmful to human health, agriculture, water bodies, and aquaculture. Among all toxic pollutants, As and F- play a significant role in groundwater contamination due to their excellent reactivity with other elements. To mitigate the prevalence of arsenic and fluoride within the water system, the use of biochar gives an attractive strategy for removing them mainly because of the substantial surface area, pore size, pH, aromatic structure, and functional groups inherent in biochar, which are primarily dependent upon its raw material and pyrolysis temperature. Researcher develops different methods like physiochemical and electrochemical for treating arsenic and fluoride contamination. Among all removal methods, bioadsorption using agricultural waste residues shows effective/feasible removal of As and F- due to its low cost, ecofriendly nature, readily available, and efficient reuse compared with several other harmful synthetic materials that demand costly design specifications. This study discusses current developments in bioadsorption methods for As and F- that use agricultural-based biomaterials and describes the prevailing state of arsenic and fluoride removal strategies that use biomaterials precisely.

Development of calcium phosphate-chitosan composites with improved removal capacity toward tetracycline antibiotic: Adsorption and electrokinetic properties

Two eco-friendly and highly efficient adsorbents, namely brushite-chitosan (DCPD-CS), and monetite-chitosan (DCPA-CS) composites were synthesized via a simple and low-cost method and used for tetracycline (TTC) removal. The removal behavior of TTC onto the composite particles was studied considering various parameters, including contact time, pollutant concentration, and pH. The maximum TTC adsorption capacity was 138.56 and 112.48 mg/g for the DCPD-CS and DCPA-CS, respectively. Increasing the pH to 11 significantly enhanced the adsorption capacity to 223.84 mg/g for DCPD-CS and 205.92 mg/g for DCPA-CS. The antibiotic adsorption process was well-fitted by the pseudo-second-order kinetic and Langmuir isotherm models. Electrostatic attractions, complexation, and hydrogen bonding are the main mechanisms governing the TTC removal process. Desorption tests demonstrated that the (NH4)2HPO4 solution was the most effective desorbing agent. The developed composites were more efficient than DCPD and DCPA reference samples and could be used as valuable adsorbents of TTC from contaminated wastewater.

Enhanced Adsorptive Removal of Tetracycline by Phosphomolybdic Acid-Modified Low-Temperature Sludge Biochar

Increasing the adsorption capacity and reducing the energy consumption of sludge biochar during preparation is important. In this study, a new modification method was developed to prepare phosphomolybdic acid-modified sludge biochar through the low-temperature pyrolysis of sewage sludge using phosphomolybdic acid as a modifier. Tetracycline was used to assess the adsorption performance of sludge biochar, and phosphomolybdic acid-modified sludge biochar was prepared at different temperatures. The results showed that the adsorption capacity of sludge biochar improved from 84.49 to 120.86 mg/g through modification with phosphomolybdic acid at 200 °C. The maximum adsorption capacities of phosphomolybdic acid-modified sludge biochar (200 °C pyrolysis temperature) at 298, 308, and 318 K were 283.87, 421.39, and 545.48 mg/g, respectively. Both liquid film and intraparticle diffusion were the main rate-limiting steps of tetracycline adsorption by phosphomolybdic acid-modified sludge biochar. Furthermore, the adsorption of tetracycline by phosphomolybdic acid-modified sludge biochar was mainly attributed to π-π interactions, electrostatic interactions, hydrogen bonding, and pore filling.

Synergistic approach for synthesis of functionalized biochar for efficient adsorption of Lopinavir from polluted water

The COVID-19 pandemic has led to a significant increase in antibiotic consumption, along with a 70% rise in antiviral drug concentrations in aquatic ecosystems. For the effective adsorption of antibiotics, biochar was modified by incorporating layered double hydroxide (LDH) through hydrothermal method. The results showed that LDH provides additional hydroxyl groups, positive surface charges and ion exchange. Whereas biochar component provides a larger specific surface area (467.8 m2/g). Batch adsorption experiments of biochar @ layered double hydroxide (BC@LDH) showed enhanced adsorption performance (832.9 mg/g), compared to pristine LDH (420.3 mg/g) and unmodified biochar (548.5 mg/g). Adsorption data were best interpreted (R2 = 0.99) by pseudo second order, Freundlich, and Temkin isotherm models. Adsorption was a synergism of LDH and biochar physiochemical properties, whereas pore-filling was the primary mechanism. The recyclability of BC@LDH confirmed its good structural stability. This study introduces a sustainable and efficient method for synthesizing a versatile adsorbent with superior antibiotic removal.

Highly porous BiOBr@NU-1000 Z-scheme heterojunctions for synergistic efficient adsorption and photocatalytic degradation of tetracycline

Designing an effective photoactive heterojunction having dual benefits towards photoenergy conversion and pollutant adsorption is regarded as an affordable, green method for eliminating tetracycline (TC) from wastewater. In this regard, a series of BiOBr@NU-1000 (BNU-X, X = 1, 2 and 3) heterojunction photocatalysts are constructed. BNU-X preserves the original skeleton structure of the parent NU-1000, and its high porosity and specific surface area enable superior TC adsorption. At the same time, BNU-X is an effective Z-scheme photocatalyst that improves light trapping, promotes photoelectron-hole separation, and shows excellent photocatalytic degradation efficiency towards TC with the value of the photodegradation kinetic rate constant k being 2.2 and 24.8 times those of NU-1000 and BiOBr, respectively. The significant increase in the photocatalytic activity is ascribed to the construction of an efficient Z-scheme photocatalyst, which promotes the formation of superoxide radicals (˙O2-) and singlet oxygen (1O2) as the main oxidative species in the oxidation system. This research has the advantage of possibilities for the development of porous Z-scheme photocatalysts based on photoactive MOF materials and inorganic semiconductors for the self-purification and photodegradation of organic contaminants.

Microalgae-based biochar production and applications: A comprehensive review

Biochar, a solid carbonaceous substance synthesized from the thermochemical degradation of biomass, holds significant potential in addressing global challenges such as soil degradation, environmental pollution, and climate change. Its potential as a carbon sequestration agent, together with its versatile applications in soil amendments, pollutant adsorption, and biofuel production, has garnered attention. On the other hand, microalgae, with their outstanding photosynthetic efficiency, adaptability, and ability to accumulate carbohydrates and lipids, have demonstrated potential as emerging feedstock for biochar production. However, despite the significant potential of microalgal biochar, our current understanding of its various aspects, such as the influence of parameters, chemical modifications, and applications, remains limited. Therefore, this review aims to provide a comprehensive analysis of microalgae-based biochar, covering topics such as production techniques, pollutant removal, catalytic applications, soil amendments, and synthesis of carbon quantum dots to bridge the existing knowledge gap in this field.

Biochar production and its environmental applications: Recent developments and machine learning insights

Biochar production through thermochemical processing is a sustainable biomass conversion and waste management approach. However, commercializing biochar faces challenges requiring further research and development to maximize its potential for addressing environmental concerns and promoting sustainable resource management. This comprehensive review presents the state-of-the-art in biochar production, emphasizing quantitative yield and qualitative properties with varying feedstocks. It discusses the technology readiness level and commercialization status of different production strategies, highlighting their environmental and economic impacts. The review focuses on integrating machine learning algorithms for process control and optimization in biochar production, improving efficiency. Additionally, it explores biochar's environmental applications, including soil amendment, carbon sequestration, and wastewater treatment, showcasing recent advancements and case studies. Advances in biochar technologies and their environmental benefits in various sectors are discussed herein.

Ferrous disulfide and iron nitride sites on hydrochar to enhance synergistic adsorption and reduction of hexavalent chromium

In this study, a novel hydrochar containing ferrous disulfide (FeS2) and iron nitride (FeN) was prepared via a one-pot hydrothermal method to enhance the synergistic adsorption and reduction of hexavalent chromium (Cr(VI)). This material (Fe3-SNHC) exhibited a Cr(VI) removal capacity of 431.3 mg·g-1 and high tolerance to coexisting anions at pH 2. Adsorption occurred via monolayer chemisorption. Variation in material structure and density functional theory calculations proved that multiple active sites formed by interactions between heteroatoms improved the chemical inertness of hydrochar. FeN and FeS2 with two electron-donating groups had strong reducing ability to facilitate the conversion of Cr(VI) to trivalent chromium. It was concluded that next to electrostatic adsorption and complexation, synergistic reduction among multiple active sites were the dominant mechanisms involved in the removal Cr(VI). This study shows that Fe3-SNHC is a promising and environment-friendly material for Cr(VI) to remove it from wastewater.

Comprehensive adsorption and spectroscopic studies on the interaction of magnetic biochar from black wattle sawdust with beta-blocker metoprolol

The rise of contaminants of emerging concern in water-resources due to human activities has driven research toward wastewater treatment, specifically adsorption. The utilization of woody biomass for biochar production in adsorption has shown promise due to its high availability. This study shows the preparation of magnetic biochars (MB) from waste black wattle sawdust, utilizing ZnCl2 and NiCl2 (proportions: 1:0.5:0.5 = MB-0.5 and 1:1:1 = MB-1) as activating and magnetic agents. Synthesized via microwave-assisted-pyrolysis, MB boasts a high surface area (up to 765 m2.g-1) and functional groups, enhancing metoprolol medicine adsorption. Nonlinear kinetic and isothermal models were tested; the Avrami fractional-order kinetic model and Liu's isothermal model provided the best fits for experimental data. Thermodynamics and spectroscopic studies revealed spontaneous and exothermic adsorption processes, with physisorption magnitude and dominance of hydrogen-bond and π-π-interactions. MB can be easily extracted from an aqueous medium using magnetic fields, while adsorption capacity could be regenerated through green solvent elution.

Photocatalysis-PMS oxidation system based on CQDs-doped carbon nitride nanosheets for degradation of residual drugs in water

Graphite-like carbon nitride (g-C3N4) is favored for its excellent physicochemical properties. However, the high complexation rate of photogenerated carriers greatly limits its practical applications. Based on this, a novel CQDs-doped carbon nitride nanosheets composite (CNS/CQDs) was prepared and applied to the visible light-induced activation of peroxymonosulfate (PMS) for meloxicam (Mel) and tetracycline (TC) degradation. The photocatalytic degradation of Mel and TC were remarkably promoted in the CNS/CQDs+PMS+vis system. Mel photodegradation of 99.90% was achieved over 30 min with 20 mg CNS/CQDs and 20 mg PMS at pH11. And TC photodegradation of 95.97% was achieved over 45 min with 20 mg CNS/CQDs and 20 mg PMS at nature pH6.5. The TOC mineralization rates of Mel and TC were 75.49% and 52.00%, respectively. The transient photocurrent response and electrochemical impedance measurements (EIS) results indicated that the doping of CQDs could improve the charge transfer efficiency of pure g-C3N4, and CNS/CQDs had a low charge transfer resistance. Capture experiments and EPR tests explored the effective actives in the CNS/CQDs+PMS+vis system. Possible degradation pathways of Mel were also analyzed. This study provides valid residual drugs degradation under the dual conditions of visible light catalytic oxidation and persulfate oxidation, which will be a novel perspective for advanced oxidation technology to effectively remove organic pollutants from water.