Heteroleptic bis-diimine copper(I) complexes for applications in solar energy conversion

Single Component Dye-Sensitized Solar Cells Enabled by Copper Chemistry: Introduction of the Retro Cell

The possibility of utilizing a single molecule to act as both a chromophore and a redox shuttle in a new configuration of a dye-sensitized solar cell (DSSC) is investigated. This design, termed a retro cell, exploits the copper chromophore, [Cu(dsbtmp)2]+ (dsbtmp = bis(2,9-di(sec-butyl)-3,4,7,8-tetramethyl-1,10-phenanthroline), which has been shown to have excited state lifetimes in excess of a microsecond, enabling sensitization of TiO2 while dissolved in solution. The oxidized chromophore can then diffuse to the counter electrode to be regenerated. This concept simplifies the device components and fabrication and eliminates a charge transfer step compared to that of traditional DSSCs. Initial investigations show the concept is viable; however, the performance is suboptimal. We have found the addition of 4-tert-butylpyridine (TBP) to the electrolyte plays a crucial role in enabling solar energy conversion. Evidence of TBP displacing one of the dsbtmp ligands in the oxidized [Cu(dsbtmp)2]2+ complex has been presented, which likely plays an important role in reducing recombination and enabling charge collection. The performance-limiting steps and routes to improved performance and viability of a retro cell are further discussed.

Charge separation in a copper(I) donor-chromophore-acceptor assembly for both photoanode and photocathode sensitization

A copper(I) donor-chromophore-acceptor triad bearing 1,8-napthalenemonoimide as the electron acceptor and triphenylamine as the electron donor was synthesized. Photophysical and electrochemical characterization suggest stepwise photoinduced charge separation upon excitation of the copper(I)-based metal-to-ligand charge transfer (MLCT) transition. Analyses of femtosecond transient absorption data of the triad show that intersystem crossing from the 1MLCT to the 3MLCT state is followed by two electron-transfer steps with time constants of 20 ps and 722 ps yielding a presumed final charge-separated state with a radical cation on the donor and radical anion on the acceptor that has an 18 ns lifetime in acetonitrile. Finally, this triad was anchored onto n-type (ZnO) and p-type (NiO) semiconductor surfaces to construct a photoanode and photocathode respectively. Successful photocurrent generation from both electrodes upon white light illumination confirms the potential utilization of such systems in dye-sensitized photoelectrochemical cells.

Copper complex molecules as dye-sensitizers: Hybrid MetaGGA and standard + van der Waals functionals

This study focuses on the use of Density Functional Theory calculations with two main approaches: computational chemistry and computational physics. The following three cases were considered for the derivation: (I) computational chemistry using the M06 hybrid functional, (II) computational chemistry using the standard PBE functional including vdW interactions, and (III) computational physics using the standard PBE functional including vdW interactions and periodic boundary conditions. Since the approximation using hybrid functionals M06 has been extensively validated, this method was used as a reference. The second and third methods are less expensive, it is ideal for use to extend large systems. From the sensitized molecules are found in the gas phase and include solvent effects through the integral equation formalism polarizable continuum model. In a systematic analysis of 15 Cu complex molecules, a complete characterization for DSSCs has been carried out and molecular geometry, electronic and optical measurements have been reported.

Photodriven electron-transfer dynamics in a series of heteroleptic Cu(I)-anthraquinone dyads

Solar fuels catalysis is a promising route to efficiently harvesting, storing, and utilizing abundant solar energy. To achieve this promise, however, molecular systems must be designed with sustainable components that can balance numerous photophysical and chemical processes. To that end, we report on the structural and photophysical characterization of a series of Cu(I)-anthraquinone-based electron donor-acceptor dyads. The dyads utilized a heteroleptic Cu(I) bis-diimine architecture with a copper(I) bis-phenanthroline chromophore donor and anthraquinone electron acceptor. We characterized the structures of the complexes using x-ray crystallography and density functional theory calculations and the photophysical properties via resonance Raman and optical transient absorption spectroscopy. The calculations and resonance Raman spectroscopy revealed that excitation of the Cu(I) metal-to-ligand charge-transfer (MLCT) transition transfers the electron to a delocalized ligand orbital. The optical transient absorption spectroscopy demonstrated that each dyad formed the oxidized copper-reduced anthraquinone charge-separated state. Unlike most Cu(I) bis-phenanthroline complexes where increasingly bulky substituents on the phenanthroline ligands lead to longer MLCT excited-state lifetimes, here, we observe a decrease in the long-lived charge-separated state lifetime with increasing steric bulk. The charge-separated state lifetimes were best explained in the context of electron-transfer theory rather than with the energy gap law, which is typical for MLCT excited states, despite the complete conjugation between the phenanthroline and anthraquinone moieties.

Iron-Sensitized Solar Cells (FeSSCs)

ConspectusThe harvesting and conversion of solar energy have become a burning issue for our modern societies seeking to move away from the exploitation of fossil fuels. In this context, dye-sensitized solar cells (DSSCs) have proven to be trustworthy alternatives to silicon-based cells with advantages in terms of transparency and efficiency under low illumination conditions. These devices are highly dependent on the ability of the sensitizer that they contain to collect sunlight and transfer an electron to a semiconductor after excitation. Ruthenium and polypyridine complexes are benchmarks in this field as they exhibit ideal characteristics such as long-lasting metal-ligand charge transfer (MLCT) states and efficient separation between electrons and holes, limiting recombination at the dye-semiconductor interface. Despite all of these advantages, ruthenium is a noble metal, and the development of more sustainable energy devices based on earth-abundant metals is now a must. A quick glance at the periodic table reveals iron as a potential good candidate, since it belongs to the same group of ruthenium, which suggests similar electronic properties. However, striking photophysical differences exist between ruthenium(II) polypyridyl complexes and their Fe(II) analogues, the latter suffering from short-lived MLCT states resulting of their ultrafast relaxation into metal-centered (MC) states. Pyridyl-N-heterocyclic carbenes (pyridylNHC) brought a strong σ-donor character required to promote a higher ligand field splitting of the iron d orbitals. This induces destabilization of the MC states over the MLCT manifold and a consequent slowdown of the excited states deactivation providing iron(II) complexes with tens of picoseconds lifetimes, making them more promising for applications in DSSCs. This Account highlights our recent advances in the development and characterization of iron-sensitized solar cells (FeSSCs) with a focus on the design of efficient sensitizers going from homoleptic to heteroleptic complexes (bearing different anchoring groups) and the tuning of electrolyte composition. Our rational approach led to the best photocurrent and efficiency ever reported for an iron sensitized solar cell (2% PCE and 9 mA/cm2) using a cosensitization process. This work clearly evidences that the solar energy conversion based on iron complex sensitization is now an opened and fruitful route.

Syntheses, characterization, crystal structures and applications as sensitizers in solar cells of novel heteroleptic Cu(I) complexes containing nitrile-substituted 2,2'-bipyridyl ligands

Two novel Cu(I) tetradentate heteroleptic complexes, including nitrile-substituted bipyridines that can be anchored to semiconductor surfaces to be assembled in DSSCs, were synthesized and characterized by spectroscopic and electrochemical techniques. The crystal structures of both species were determined by X-ray diffraction. Results from DFT and TD-DFT calculations were found to be consistent with the experimental data. Emission at room temperature was observed for both complexes in the solid state, making them promising alternatives for the development of light-emitting diodes. We report for the first time the experimental evidence of photovoltaic conversion devices formed by Cu(I) complexes anchored to a TiO2 surface by means of nitrile groups present in substituted bipyridines, and subsequently tested as sensitizers for DSSCs, obtaining efficiency values for light to electrical energy conversion similar to those previously reported for analogous complexes with anchoring carboxylic groups.

Photochemical charge accumulation in a heteroleptic copper(i)-anthraquinone molecular dyad via proton-coupled electron transfer

Developing efficient photocatalysts that perform multi electron redox reactions is critical to achieving solar energy conversion. One can reach this goal by developing systems which mimic natural photosynthesis and exploit strategies such as proton-coupled electron transfer (PCET) to achieve photochemical charge accumulation. We report herein a heteroleptic Cu(i)bis(phenanthroline) complex, Cu-AnQ, featuring a fused phenazine-anthraquinone moiety that photochemically accumulates two electrons in the anthraquinone unit via PCET. Full spectroscopic and electrochemical analyses allowed us to identify the reduced species and revealed that up to three electrons can be accumulated in the phenazine-anthraquinone ring system under electrochemical conditions. Continuous photolysis of Cu-AnQ in the presence of sacrificial electron donor produced doubly reduced monoprotonated photoproduct confirmed unambiguously by X-ray crystallography. Formation of this photoproduct indicates that a PCET process occurred during illumination and two electrons were accumulated in the system. The role of the heteroleptic Cu(i)bis(phenanthroline) moiety participating in the photochemical charge accumulation as a light absorber was evidenced by comparing the photolysis of Cu-AnQ and the free AnQ ligand with less reductive triethylamine as a sacrificial electron donor, in which photogenerated doubly reduced species was observed with Cu-AnQ, but not with the free ligand. The thermodynamic properties of Cu-AnQ were examined by DFT which mapped the probable reaction pathway for photochemical charge accumulation and the capacity for solar energy stored in the process. This study presents a unique system built on earth-abundant transition metal complex to store electrons, and tune the storage of solar energy by the degree of protonation of the electron acceptor.

Changing Directions: Influence of Ligand Electronics on the Directionality and Kinetics of Photoinduced Charge Transfer in Cu(I)Diimine Complexes

A key challenge to the effective utilization of solar energy is to promote efficient photoinduced charge transfer, specifically avoiding unproductive, circuitous electron-transfer pathways and optimizing the kinetics of charge separation and recombination. We hypothesize that one way to address this challenge is to develop a fundamental understanding of how to initiate and control directional photoinduced charge transfer, particularly for earth-abundant first-row transition-metal coordination complexes, which typically suffer from relatively short excited-state lifetimes. Here, we report a series of functionalized heteroleptic copper(I)bis(phenanthroline) complexes, which have allowed us to investigate the directionality of intramolecular photoinduced metal-to-ligand charge transfer (MLCT) as a function of the substituent Hammett parameter. Ultrafast transient absorption suggests a complicated interplay of MLCT localization and solvent interaction with the Cu(II) center of the MLCT state. This work provides a set of design principles for directional charge transfer in earth-abundant complexes and can be used to efficiently design pathways for connecting the molecular modules to catalysts or electrodes and integration into systems for light-driven catalysis.

Triplet quenching pathway control with molecular dyads enables the identification of a highly oxidizing annihilator class

Metal complex - arene dyads typically act as more potent triplet energy donors compared to their parent metal complexes, which is frequently exploited for increasing the efficiencies of energy transfer applications. Using unexplored dicationic phosphonium-bridged ladder stilbenes (P-X2+) as quenchers, we exclusively observed photoinduced electron transfer photochemistry with commercial organic photosensitizers and photoactive metal complexes. In contrast, the corresponding pyrene dyads of the tested ruthenium complexes with the very same metal complex units efficiently sensitize the P-X2+ triplets. The long-lived and comparatively redox-inert pyrene donor triplet in the dyads thus provides an efficient access to acceptor triplet states that are otherwise very tricky to obtain. This dyad-enabled control over the quenching pathway allowed us to explore the P-X2+ photochemistry in detail using laser flash photolysis. The P-X2+ triplet undergoes annihilation producing the corresponding excited singlet, which is an extremely strong oxidant (+2.3 V vs. NHE) as demonstrated by halide quenching experiments. This behavior was observed for three P2+ derivatives allowing us to add a novel basic structure to the very limited number of annihilators for sensitized triplet-triplet annihilation in neat water.

Bichromophoric Photosensitizers: How and Where to Attach Pyrene Moieties to Phenanthroline to Generate Copper(I) Complexes

Pyrene is a polycyclic aromatic hydrocarbon and organic dye that can form superior bichromophoric systems when combined with a transition metal-based chromophore. However, little is known about the effect of the type of attachment (i.e., 1- vs 2-pyrenyl) and the individual position of the pyrenyl substituents at the ligand. Therefore, a systematic series of three novel diimine ligands and their respective heteroleptic diimine-diphosphine copper(I) complexes has been designed and extensively studied. Special attention was given to two different substitution strategies: (i) attaching pyrene via its 1-position, which occurs most frequently in the literature, or via its 2-position and (ii) targeting two contrasting substitution patterns at the 1,10-phenanthroline ligand, i.e., the 5,6- and the 4,7-position. In the applied spectroscopic, electrochemical, and theoretical methods (UV/vis, emission, time-resolved luminescence and transient absorption, cyclic voltammetry, density functional theory), it has been shown that the precise choice of the derivatization sites is crucial. Substituting the pyridine rings of phenanthroline in the 4,7-position with the 1-pyrenyl moiety has the strongest impact on the bichromophore. This approach results in the most anodically shifted reduction potential and a drastic increase in the excited state lifetime by more than two orders of magnitude. In addition, it enables the highest singlet oxygen quantum yield of 96% and the most beneficial activity in the photocatalytic oxidation of 1,5-dihydroxy-naphthalene.

Reaching strong absorption up to 700 nm with new benzo[g]quinoxaline-based heteroleptic copper(I) complexes for light-harvesting applications

Heteroleptic copper(I) complexes, with a diimine as a chromophoric unit and a bulky diphosphine as an ancillary ligand, have the advantage of a reduced pseudo Jahn-Teller effect in their excited state over the corresponding homoleptic bis(diimine) complexes. Nevertheless, their lowest absorption lies generally between 350 to 500 nm. Aiming at a strong absorption in the visible by stable heteroleptic Cu(I) complexes, we designed a novel diimine based on 4-(benzo[g]quinoxal-2'-yl)-1,2,3-triazole derivatives. The large π-conjugation of the benzoquinoxaline moiety shifted bathochromically the absorption with regard to other diimine-based Cu(I) complexes. Adding another Cu(I) core broadened the absorption and extended it to considerably longer wavelengths. Moreover, by fine-tuning the structure of the dichelating ligand, we achieved a panchromatic absorption up to 700 nm with a high molar extinction coefficient of 8000 M^-1 cm^-1 at maximum (λ = 570 nm), making this compound attractive for light-harvesting antennae.

DFT study of UV-vis-properties of thiophene-containing Cu(β-diketonato)2 - Application for DSSC

Experimental and theoretically calculated UV-vis properties of three Cu(β-diketonato)₂ complexes are presented. The Cu(β-diketonato)₂ contains β-diketones without (β-diketone = acetylacetone, (CH₃)COCH₂CO(CH₃), complex (1)), with one (β-diketone = thenoyltrifluoroacetone, (CF₃)COCH₂CO(C₄H₃S), complex (2)) and with two thiophene (β-diketone = (CF₃)COCH₂CO(C₄H₂S) (C₄H₃S), complex (3)) groups. More thiophenes on the β-diketonato ligand of Cu(β-diketonato)₂, lead to a red shift of the experimental absorbance maxima of the UV-vis of the complex, from 295 nm for complex (1), to 340 nm for complex (2) to 390 nm for complex (3). Theoretical time dependant density functional theory calculations indicate that both the two strongest absorbance peaks of the ultraviolet-visible spectrum of Cu(acetylacetonato)₂ are mainly ligand-to-metal charge-transfer excitations. However, the absorbance maxima of the UV-vis of thiophene-containing Cu(β-diketonato)₂ are mainly ligand-to-ligand charge-transfer excitations. Calculated properties such as light harvesting energy (LHE = 0.47, 0.94 and 0.99 for (1)-(3) respectively), driving force for electron injection (ΔG_inject = 1.43, 0.76 and 0.63 for (1)-(3) respectively), and driving force of dye regeneration (ΔG_regenerate = 1.85, 2.16 and 1.49 for (1)-(3) respectively), are favourable for (1)-(3) to be considered as dyes in DSSCs. However, some structural modifications are needed to prevent intramolecular charge recombination after excitation.

Panchromatic light harvesting and record power conversion efficiency for carboxylic/cyanoacrylic Fe(ii) NHC co-sensitized FeSSCs

The co-sensitization of TiO2 by using a combination of carboxylic and thienylcyanoacrylic (ThCA)–Fe(ii) pyridyl-NHC sensitizers produced a panchromatic absorption and the best photocurrent and efficiency ever reported for an FeSSC.

Photophysics of Anionic Bis(4H-imidazolato)CuI Complexes

In this paper, the photophysical behavior of four panchromatically absorbing, homoleptic bis(4H-imidazolato)CuI complexes, with a systematic variation in the electron-withdrawing properties of the imidazolate ligand, were studied by wavelength-dependent time-resolved femtosecond transient absorption spectroscopy. Excitation at 400, 480, and 630 nm populates metal-to-ligand charge transfer, intraligand charge transfer, and mixed-character singlet states. The pump wavelength-dependent transient absorption data were analyzed by a recently established 2D correlation approach. Data analysis revealed that all excitation conditions yield similar excited-state dynamics. Key to the excited-state relaxation is fast, sub-picosecond pseudo-Jahn-Teller distortion, which is accompanied by the relocalization of electron density onto a single ligand from the initially delocalized state at Franck-Condon geometry. Subsequent intersystem crossing to the triplet manifold is followed by a sub-100 ps decay to the ground state. The fast, nonradiative decay is rationalized by the low triplet-state energy as found by DFT calculations, which suggest perspective treatment at the strong coupling limit of the energy gap law.

Photoactive Copper Complexes: Properties and Applications

Photocatalyzed and photosensitized chemical processes have seen growing interest recently and have become among the most active areas of chemical research, notably due to their applications in fields such as medicine, chemical synthesis, material science or environmental chemistry. Among all homogeneous catalytic systems reported to date, photoactive copper(I) complexes have been shown to be especially attractive, not only as alternative to noble metal complexes, and have been extensively studied and utilized recently. They are at the core of this review article which is divided into two main sections. The first one focuses on an exhaustive and comprehensive overview of the structural, photophysical and electrochemical properties of mononuclear copper(I) complexes, typical examples highlighting the most critical structural parameters and their impact on the properties being presented to enlighten future design of photoactive copper(I) complexes. The second section is devoted to their main areas of application (photoredox catalysis of organic reactions and polymerization, hydrogen production, photoreduction of carbon dioxide and dye-sensitized solar cells), illustrating their progression from early systems to the current state-of-the-art and showcasing how some limitations of photoactive copper(I) complexes can be overcome with their high versatility.

Photocatalytic Reduction of CO2 to CO in Aqueous Solution under Red-Light Irradiation by a Zn-Porphyrin-Sensitized Mn(I) Catalyst

This work demonstrates photocatalytic CO₂ reduction by a noble-metal-free photosensitizer-catalyst system in aqueous solution under red-light irradiation. A water-soluble Mn(I) tricarbonyl diimine complex, [MnBr(4,4′-{Et₂O₃PCH₂}₂-2,2′-bipyridyl)(CO)₃] (1), has been fully characterized, including single-crystal X-ray crystallography, and shown to reduce CO₂ to CO following photosensitization by tetra(N-methyl-4-pyridyl)porphyrin Zn(II) tetrachloride [Zn(TMPyP)]Cl₄ (2) under 625 nm irradiation. This is the first example of 2 employed as a photosensitizer for CO₂ reduction. The incorporation of −P(O)(OEt)₂ groups, decoupled from the core of the catalyst by a −CH₂– spacer, afforded water solubility without compromising the electronic properties of the catalyst. The photostability of the active Mn(I) catalyst over prolonged periods of irradiation with red light was confirmed by ¹H and ¹³C{¹H} NMR spectroscopy. This first report on Mn(I) species as a homogeneous photocatalyst, working in water and under red light, illustrates further future prospects of intrinsically photounstable Mn(I) complexes as solar-driven catalysts in an aqueous environment.

A Mn(I) bipyridyl tricarbonyl complex, where the diimine ligand is functionalized with water-solubilizing phosphonate ester groups, has been prepared and is shown to catalytically convert CO₂ to CO in aqueous solution following photosensitization from a water-soluble Zn(II) porphyrin under red-light irradiation.

So Close, Yet so Different: How One Donor Atom Changes Significantly the Photophysical Properties of Mononuclear Cu(I) Complexes

The manipulation of the photophysical properties of molecular emitters can be realized by composing the close environment of the metal center with the "heavier pnictogen atom" effect. Replacing a nitrogen atom with a heavier phosphorus atom in otherwise isostructural molecular systems results in a significant change of the photophysical parameters. Herein, we report on the synthesis of four pairs of novel phosphinine-based and isostructural diimine-based Cu(I) complexes, which feature peculiar photophysical properties, and show how these parameters depend on the "heavier pnictogen atom" effect. The obtained Cu(I) complexes show triplet luminescence with MLCT character, which was investigated by means of spectroscopic and computational methods. It has been found that the photophysical properties of the coordination compounds show a dependency on the rigidity of the ancillary phosphine ligand in an unexpected manner. Replacing the nitrogen atom with a heavier phosphorus atom in otherwise isostructural molecular systems results in a significant change in emission energy and especially in the lifetime of the excited state. The results obtained demonstrate an efficient approach to the design of emissive molecular materials, which allows the construction of luminescent complexes with controlled photophysical properties.

Heteroleptic Copper(I)-Based Complexes Incorporating BINAP and π-Extended Diimines: Synthesis, Catalysis and Biological Applications

A series of copper-based photocatalysts of the type Cu(NN)(BINAP)BF₄ were synthesized bearing π-extended diimine ligands. Their behavior in several photocatalytic processes were evaluated and revealed acceptable levels of activity in an SET process, but negligible activity in PCET or ET processes. Suitable activity in ET processes could be restored through modification of the ligand. The BINAP-derived complexes were then evaluated for activity against triple-negative breast cancer cell lines. Controls indicated that copper complexes, and not their ligands, were responsible for activity. Encouraging activity was displayed by a homoleptic complex Cu(dppz)₂BF₄.

Ligand‐Induced Donor State Destabilisation – A New Route to Panchromatically Absorbing Cu(I) Complexes

The intense absorption of light to covering a large part of the visible spectrum is highly desirable for solar energy conversion schemes. To this end, we have developed novel anionic bis(4H‐imidazolato)Cu(I) complexes (cuprates), which feature intense, panchromatic light absorption properties throughout the visible spectrum and into the NIR region with extinction coefficients up to 28,000 M⁻¹ cm⁻¹. Steady‐state absorption, (spectro)electrochemical and theoretical investigations reveal low energy (Vis to NIR) metal‐to‐ligand charge‐transfer absorption bands, which are a consequence of destabilized copper‐based donor states. These high‐lying copper‐based states are induced by the σ‐donation of the chelating anionic ligands, which also feature low energy acceptor states. The optical properties are reflected in very low, copper‐based oxidation potentials and three ligand‐based reduction events. These electronic features reveal a new route to panchromatically absorbing Cu(I) complexes.

Effect of the Ancillary Ligand on the Performance of Heteroleptic Cu(I) Diimine Complexes as Dyes in Dye-Sensitized Solar Cells

A series of heteroleptic Cu(I) diimine complexes with different ancillary ligands and 6,6'-dimethyl-2,2'-bipyridine-4,4'-dibenzoic acid (dbda) as the anchoring ligand were self-assembled on TiO₂ surfaces and used as dyes for dye-sensitized solar cells (DSSCs). The binding to the TiO₂ surface was studied by hard X-ray photoelectron spectroscopy for a bromine-containing complex, confirming the complex formation. The performance of all complexes was assessed and rationalized on the basis of their respective ancillary ligand. The DSSC photocurrent-voltage characteristics, incident photon-to-current conversion efficiency (IPCE) spectra, and calculated lowest unoccupied molecular orbital (LUMO) distributions collectively show a push-pull structural dye design, in which the ancillary ligand exhibits an electron-donating effect that can lead to improved solar cell performance. By analyzing the optical properties of the dyes and their solar cell performance, we can conclude that the presence of ancillary ligands with bulky substituents protects the Cu(I) metal center from solvent coordination constituting a critical factor in the design of efficient Cu(I)-based dyes. Moreover, we have identified some components in the I^-/I₃ ^--based electrolyte that causes dissociation of the ancillary ligand, i.e., TiO₂ photoelectrode bleaching. Finally, the detailed studies on one of the dyes revealed an electrolyte-dye interaction, leading to a dramatic change of the dye properties when adsorbed on the TiO₂ surface.

Solar energy conversion using first row d-block metal coordination compound sensitizers and redox mediators

The use of renewable energy is essential for the future of the Earth, and solar photons are the ultimate source of energy to satisfy the ever-increasing global energy demands. Photoconversion using dye-sensitized solar cells (DSCs) is becoming an established technology to contribute to the sustainable energy market, and among state-of-the art DSCs are those which rely on ruthenium(ii) sensitizers and the triiodide/iodide (I3 -/I-) redox mediator. Ruthenium is a critical raw material, and in this review, we focus on the use of coordination complexes of the more abundant first row d-block metals, in particular copper, iron and zinc, as dyes in DSCs. A major challenge in these DSCs is an enhancement of their photoconversion efficiencies (PCEs) which currently lag significantly behind those containing ruthenium-based dyes. The redox mediator in a DSC is responsible for regenerating the ground state of the dye. Although the I3 -/I- couple has become an established redox shuttle, it has disadvantages: its redox potential limits the values of the open-circuit voltage (V OC) in the DSC and its use creates a corrosive chemical environment within the DSC which impacts upon the long-term stability of the cells. First row d-block metal coordination compounds, especially those containing cobalt, and copper, have come to the fore in the development of alternative redox mediators and we detail the progress in this field over the last decade, with particular attention to Cu2+/Cu+ redox mediators which, when coupled with appropriate dyes, have achieved V OC values in excess of 1000 mV. We also draw attention to aspects of the recyclability of DSCs.

Dependence between luminescence properties of Cu(i) complexes and electronic/structural parameters derived from steric effects

Quantification of steric effects induced by bulky N^N ligands and their relationship with the luminescence properties of Cu(i) complexes.

Modulating the Excited-State Decay Pathways of Cu(I) 4H-Imidazolate Complexes by Excitation Wavelength and Ligand Backbone

Cu(I) 4H-imidazolato complexes are excellent photosensitizers with broad and intense light absorption properties, based on an earth-abundant metal, and hold great promise as photosensitizers in artificial photosynthesis and for accumulation of redox equivalents. In this study, the excited-state relaxation dynamics of three novel heteroleptic Cu(I) 4H-imidazolato complexes with phenyl, tolyl, and mesityl side groups are systematically investigated by femtosecond and nanosecond time-resolved transient absorption spectroscopy and theoretical methods, complemented by steady-state absorption spectroscopy and (spectro)electrochemistry. After photoexcitation into the metal-to-ligand charge transfer (MLCT) and intraligand charge transfer absorption band, fast (0.6-1 ps) intersystem crossing occurs into the triplet MLCT manifold. The triplet-state population relaxes via the geometrical planarization of the N-aryl rings on the Cu(I) 4H-imidazolato complexes. Depending on the initial Franck-Condon state, the remaining small singlet state population relaxes into two geometrically distinct minima geometries with similar energy, S_1/2,relax and S_3/4,relax. Subsequent ground-state recovery from S_1/2,relax and internal conversion from S_3/4,relax to S_1/2,relax take place on a 100 ps time scale. The internal conversion can be understood as hole transfer from a d_yz-orbital to a d_xz-orbital, which is accompanied with the structural reorganization of the coordination environment. Generally, the photophysical processes are determined by the steric hindrance of the side groups on the ligands. And the excited singlet-state pathways are dependent on the excitation wavelength.

Electrolyte Tuning in Iron(II)-Based Dye-Sensitized Solar Cells: Different Ionic Liquids and I2 Concentrations

The effects of different I₂ concentrations and different ionic liquids (ILs) in the electrolyte on the performances of dye-sensitized solar cells (DSCs) containing an iron(II) N-heterocyclic carbene dye and containing the I^–/I₃^– redox shuttle have been investigated. Either no I₂ was added to the electrolyte, or the initial I₂ concentrations were 0.02, 0.05, 0.10, and 0.20 M. The short-circuit current density (J_SC), open-circuit voltage (V_OC), and the fill factor (ff) were influenced by changes in the I₂ concentration for all the ILs. For 1-hexyl-3-methylimidazole iodide (HMII), low V_OC and low ff values led to poor DSC performances. Electrochemical impedance spectroscopy (EIS) showed the causes to be increased electrolyte diffusion resistance and charge transfer resistance at the counter electrode. DSCs containing 1,3-dimethylimidazole iodide (DMII) and 1-ethyl-3-methylimidazole iodide (EMII) showed the highest J_SC values when 0.10 M I₂ was present initially. Short alkyl substituents (Me and Et) were more beneficial than longer chains. The lowest values of the transport resistance in the photoanode semiconductor were found for DMII, EMII, and 1-propyl-2,3-dimethylimidazole iodide (PDMII) when no I₂ was added to the initial electrolyte, or when [I₂] was less than 0.05 M. Higher [I₂] led to decreases in the diffusion resistance in the electrolyte and the counter electrode resistance. The electron lifetime and diffusion length depended upon the [I₂]. Overall, DMII was the most beneficial IL. A combination of DMII and 0.1 M I₂ in the electrolyte produced the best performing DSCs with an average maximum photoconversion efficiency of 0.65% for a series of fully-masked cells.

Cross-Coupled Phenyl- and Alkynyl-Based Phenanthrolines and Their Effect on the Photophysical and Electrochemical Properties of Heteroleptic Cu(I) Photosensitizers

With the aims of increasing the antenna system and improving the photophysical properties of Cu(I)-based photosensitizers, the backbone of 2,9-dimethyl-1,10-phenanthroline was selectively extended in the 5,6-position. Applying specifically tailored Suzuki-Miyaura and "chemistry-on-the-complex" Sonogashira cross-coupling reactions enabled the development of two sets of structurally related diimine ligands with a broad variety of different phenyl- and alkynyl-based substituents. The resulting 11 novel heteroleptic Cu(I) complexes, including five solid-state structures, were studied with respect to their structure-property relationships. Both sets of substituents are able to red-shift the absorption maxima and to increase the absorptivity. For the alkynyl-based complexes, this is accompanied by a significant anodic shift of the reduction potentials. The phenyl-based substituents strongly influence the emission wavelength and quantum yield of the resulting Cu(I) complexes and lead to an increase in the emission lifetime of up to 504 ns, which clearly indicates competition with the benchmark system [(xantphos)Cu(bathocuproine)]PF₆.

Copper Complexes as Alternative Redox Mediators in Dye-Sensitized Solar Cells

Thirty years ago, dye-sensitized solar cells (DSSCs) emerged as a method for harnessing the sun's energy and converting it into electricity. Since then, a lot of work has been dedicated to improving their global photovoltaic efficiency and their eco-sustainability. Recently, various articles showed the great potential of copper complexes as a convenient and cheap alternative to the traditional ruthenium dyes. In addition, copper complexes demonstrate that they can act as redox mediators for DSSCs, thus being an answer to the problems related to the I₃^-/I^- redox couple. The aim of this review is to report on the most recent impact made by copper complexes as alternative redox mediators. The coverage, mainly from 2016 up to now, is not exhaustive, but allows us to understand the great role played by copper complexes in the design of eco-sustainable DSSCs.

Reactivity and Mechanism of Photo- and Electrocatalytic Hydrogen Evolution by a Diimine Copper(I) Complex

The tetrahedral copper(I) diimine complex [Cu(pq)2]BF4 displays high photocatalytic activity for the H2 evolution reaction with a turnover number of 3564, thus representing the first type of a Cu(I) quinoxaline complex capable of catalyzing proton reduction. Electrochemical experiments indicate that molecular mechanisms prevail and DFT calculations provide in-depth insight into the catalytic pathway, suggesting that the coordinating nitrogens play crucial roles in proton exchange and hydrogen formation.

Multidentate Phenanthroline Ligands Containing Additional Donor Moieties and Their Resulting Cu(I) and Ru(II) Photosensitizers: A Comparative Study

To bind or not to bind: Driven by the motivation to increase the (photo)stability of traditional Cu(I) photosensitizers, multidentate diimine ligands, which contain two additional donor sites, were designed. To this end, a systematic series of four 1,10-phenanthroline ligands with either OR or SR (R = ⁱPr or Ph) donor groups at the 2 and 9 positions and their resulting hetero- and homoleptic Cu(I) complexes were prepared. In addition, the related Ru(II) complexes were also synthesized to study the effect of another metal center. In the following, a combination of NMR spectroscopy and X-ray analysis was used to evaluate the impact of the additional donor moieties on the coordination behavior. Most remarkably, for the homoleptic bis(diimine)copper(I) complexes, a pentacoordinated copper center, corresponding to a (4 + 1)-fold coordination mode, was found in the solid state. This additional binding is the first indication that the extra donor might also occupy a free coordination site in the excited-state complex, modifying the nature of the excited states and their respective deactivation processes. Therefore, the electrochemical and photophysical properties of all novel complexes (in total 13) were studied in detail to assess the potential of these photosensitizers for future applications within solar energy conversion schemes. Finally, the photostabilities and a potential degradation mechanism were analyzed for representative samples.

Surface immobilized copper(I) diimine photosensitizers as molecular probes for elucidating the effects of confinement at interfaces for solar energy conversion

Heteroleptic copper(i) bis(phenanthroline) complexes with surface anchoring carboxylate groups have been synthesized and immobilized on nanoporous metal oxide substrates. The species investigated are responsive to the external environment and this work provides a new strategy to control charge transfer processes for efficient solar energy conversion.

Evaluating heteroleptic copper(I)-based complexes bearing π-extended diimines in different photocatalytic processes

A series of 12 new copper-based photocatalysts of the type Cu(N^N)(P^P)BF4 were synthesized bearing π-extended diimine ligands. The complexes have red shifted absorptions and larger extinction coefficients than complexes prepared with a parent diimine, dmp. The complexes were evaluated for their ability to promote three different photochemical transformations. Although the complexes were inactive in a reductive PCET process, the complexes afforded good yields in both SET and ET processes. Interestingly, homoleptic copper-complexes derived from the π-extended diimines were significantly more active in SET processes than analogous complexes with simpler diimines.

Role of MLCT States in the Franck-Condon Region of Neutral, Heteroleptic Cu(I)-4H-imidazolate Complexes: A Spectroscopic and Theoretical Study

The impact of the electronic structure of a series of 4H-imidazolate ligands in neutral, heteroleptic Cu(I) complexes is investigated. Remarkable broad and strong ligand-dependent absorption in the visible range of the electromagnetic spectrum renders the studied complexes promising photosensitizers for photocatalytic applications. The electronic structure of the Cu(I) complexes and the localization of photoexcited states in the Franck-Condon region are unraveled by means of UV-vis absorption and resonance Raman (rR) spectroscopy supported by time-dependent density functional theory (TD-DFT) calculations. The visible absorption bands stem from a superposition of bright metal-to-ligand charge-transfer (MLCT) and π-π* as well as weakly absorbing MLCT states. Additionally, the analysis of involved molecular orbitals and rR spectra upon excitation of MLCT and π-π* states highlights the impact of the electronic structure of the 4H-imidazolate ligands on the properties of the corresponding Cu(I) complexes to avail a toolbox for predictive studies and efficient complex design.

The Coordination Behaviour of CuI Photosensitizers Bearing Multidentate Ligands Investigated by X-ray Absorption Spectroscopy

A systematic series of four novel homo‐ and heteroleptic Cu^I photosensitizers based on tetradentate 1,10‐phenanthroline ligands of the type X^N^N^X containing two additional donor moieties in the 2,9‐position (X=SMe or OMe) were designed. Their solid‐state structures were assessed by X‐ray diffraction. Cyclic voltammetry, UV‐vis absorption, emission and X‐ray absorption spectroscopy were then used to determine their electrochemical, photophysical and structural features in solution. Following, time‐resolved X‐ray absorption spectroscopy in the picosecond time scale, coupled with time‐dependent density functional theory calculations, provided in‐depth information on the excited state electron configurations. For the first time, a significant shortening of the Cu−X distance and a change in the coordination mode to a pentacoordinated geometry is shown in the excited states of the two homoleptic complexes. These findings are important with respect to a precise understanding of the excited state structures and a further stabilization of this type of photosensitizers.

Are Alkynyl Spacers in Ancillary Ligands in Heteroleptic Bis(diimine)copper(I) Dyes Beneficial for Dye Performance in Dye-Sensitized Solar Cells?

The syntheses of 4,4'-bis(4-dimethylaminophenyl)-6,6'-dimethyl-2,2'-bipyridine (1), 4,4'-bis(4-dimethylaminophenylethynyl)-6,6'-dimethyl-2,2'-bipyridine (2), 4,4'-bis(4-diphenylaminophenyl)-6,6'-dimethyl-2,2'-bipyridine (3), and 4,4'-bis(4-diphenylaminophenylethynyl)-6,6'-dimethyl-2,2'-bipyridine (4) are reported along with the preparations and characterisations of their homoleptic copper(I) complexes [CuL2][PF6] (L = 1-4). The solution absorption spectra of the complexes exhibit ligand-centred absorptions in addition to absorptions in the visible region assigned to a combination of intra-ligand and metal-to-ligand charge-transfer. Heteroleptic [Cu(5)(Lancillary)]+ dyes in which 5 is the anchoring ligand ((6,6'-dimethyl-[2,2'-bipyridine]-4,4'-diyl)bis(4,1-phenylene))bis(phosphonic acid) and Lancillary = 1-4 have been assembled on fluorine-doped tin oxide (FTO)-TiO2 electrodes in dye-sensitized solar cells (DSCs). Performance parameters and external quantum efficiency (EQE) spectra of the DSCs (four fully-masked cells for each dye) reveal that the best performing dyes are [Cu(5)(1)]+ and [Cu(5)(3)]+. The alkynyl spacers are not beneficial, leading to a decrease in the short-circuit current density (JSC), confirmed by lower values of EQEmax. Addition of a co-absorbent (n-decylphosphonic acid) to [Cu(5)(1)]+ lead to no significant enhancement of performance for DSCs sensitized with [Cu(5)(1)]+. Electrochemical impedance spectroscopy (EIS) has been used to investigate the interfaces in DSCs; the analysis shows that more favourable electron injection into TiO2 is observed for sensitizers without the alkynyl spacer and confirms higher JSC values for [Cu(5)(1)]+.

Schiff Base Ancillary Ligands in Bis(diimine) Copper(I) Dye-Sensitized Solar Cells

Five 6,6'-dimethyl-2,2'-bipyridine ligands bearing N-arylmethaniminyl substituents in the 4- and 4'-positions were prepared by Schiff base condensation in which the aryl group is Ph (1), 4-tolyl (2), 4-tBuC6H4 (3), 4-MeOC6H4 (4), and 4-Me2NC6H4 (5). The homoleptic copper(I) complexes [CuL2][PF6] (L = 1-5) were synthesized and characterized, and the single crystal structure of [Cu(1)2][PF6].Et2O was determined. By using the "surfaces-as-ligands, surfaces-as-complexes" (SALSAC) approach, the heteroleptic complexes [Cu(6)(Lancillary)]+ in which 6 is the anchoring ligand ((6,6'-dimethyl-[2,2'-bipyridine]-4,4'-diyl)bis(4,1-phenylene))bis(phosphonic acid)) and Lancillary = 1-5 were assembled on FTO-TiO2 electrodes and incorporated as dyes into n-type dye-sensitized solar cells (DSCs). Data from triplicate, fully-masked DSCs for each dye revealed that the best-performing sensitizer is [Cu(6)(1)]+, which exhibits photoconversion efficiencies (η) of up to 1.51% compared to 5.74% for the standard reference dye N719. The introduction of the electron-donating MeO and Me2N groups (Lancillary = 4 and 5) is detrimental, leading to a decrease in the short-circuit current densities and external quantum efficiencies of the solar cells. In addition, a significant loss in open-circuit voltage is observed for DSCs sensitized with [Cu(6)(5)]+, which contributes to low values of η for this dye. Comparisons between performances of DSCs containing [Cu(6)(1)]+ and [Cu(6)(4)]+ with those sensitized by analogous dyes lacking the imine bond indicate that the latter prevents efficient electron transfer across the dye.

Copper(I) Phosphinooxazoline Complexes: Impact of the Ligand Substitution and Steric Demand on the Electrochemical and Photophysical Properties

A series of seven homoleptic Cu^I complexes based on hetero-bidentate P^N ligands was synthesized and comprehensively characterized. In order to study structure-property relationships, the type, size, number and configuration of substituents at the phosphinooxazoline (phox) ligands were systematically varied. To this end, a combination of X-ray diffraction, NMR spectroscopy, steady-state absorption and emission spectroscopy, time-resolved emission spectroscopy, quenching experiments and cyclic voltammetry was used to assess the photophysical and electrochemical properties. Furthermore, time-dependent density functional theory calculations were applied to also analyze the excited state structures and characteristics. Surprisingly, a strong dependency on the chirality of the respective P^N ligand was found, whereas the specific kind and size of the different substituents has only a minor impact on the properties in solution. Most importantly, all complexes except C3 are photostable in solution and show fully reversible redox processes. Sacrificial reductants were applied to demonstrate a successful electron transfer upon light irradiation. These properties render this class of photosensitizers as potential candidates for solar energy conversion issues.

Sterically hindered Re- and Mn-CO2 reduction catalysts for solar energy conversion

Novel molecular Re and Mn tricarbonyl complexes bearing a bipyridyl ligand functionalised with sterically hindering substituents in the 6,6'-position, [M(HPEAB)(CO)3(X)] (M/X = Re/Cl, Mn/Br; HPEAB = 6,6'-{N-(4-hexylphenyl)-N(ethyl)-amido}-2,2'-bipyridine) have been synthesised, fully characterised including by single crystal X-ray crystallography, and their propensity to act as catalysts for the electrochemical and photochemical reduction of CO2 has been established. Controlled potential electrolysis showed that the catalysts are effective for electrochemical CO2-reduction, yielding CO as the product (in MeCN for the Re-complex, in 95 : 5 (v/v) MeCN : H2O mixture for the Mn-complex). The recyclability of the catalysts was demonstrated through replenishment of CO2 within solution. The novel catalysts had similar reduction potentials to previously reported complexes of similar structure, and results of the foot-of-the-wave analysis showed comparable maximum turnover rates, too. The tentative mechanisms for activation of the pre-catalysts were proposed on the basis of IR-spectroelectrochemical data aided by DFT calculations. It is shown that the typical dimerisation of the Mn-catalyst was prevented by incorporation of sterically hindering groups, whilst the Re-catalyst undergoes the usual mechanism following chloride ion loss. No photochemical CO2 reduction was observed for the rhenium complex in the presence of a sacrificial donor (triethylamine), which was attributed to the short triplet excited state lifetime (3.6 ns), insufficient for diffusion-controlled electron transfer. Importantly, [Mn(HPEAB)(CO)3Br] can act as a CO2 reduction catalyst when photosensitised by a zinc porphyrin under red light irradiation (λ > 600 nm) in MeCN : H2O (95 : 5); there has been only one reported example of photoactivating Mn-catalysts with porphyrins in this manner. Thus, this work demonstrates the wide utility of sterically protected Re- and Mn-diimine carbonyl catalysts, where the rate and yield of CO-production can be adjusted based on the metal centre and catalytic conditions, with the advantage of suppressing unwanted side-reactions through steric protection of the vacant coordination site.

There Is a Future for N-Heterocyclic Carbene Iron(II) Dyes in Dye-Sensitized Solar Cells: Improving Performance through Changes in the Electrolyte

By systematic tuning of the components of the electrolyte, the performances of dye-sensitized solar cells (DSCs) with an N-heterocyclic carbene iron(II) dye have been significantly improved. The beneficial effects of an increased Li+ ion concentration in the electrolyte lead to photoconversion efficiencies (PCEs) up to 0.66% for fully masked cells (representing 11.8% relative to 100% set for N719) and an external quantum efficiency maximum (EQEmax) up to approximately 25% due to an increased short-circuit current density (JSC). A study of the effects of varying the length of the alkyl chain in 1-alkyl-3-methylimidazolium iodide ionic liquids (ILs) shows that a longer chain results in an increase in JSC with an overall efficiency up to 0.61% (10.9% relative to N719 set at 100%) on going from n-methyl to n-butyl chain, although an n-hexyl chain leads to no further gain in PCE. The results of electrochemical impedance spectroscopy (EIS) support the trends in JSC and open-circuit voltage (VOC) parameters. A change in the counterion from I- to [BF4]- for 1-propyl-3-methylimidazolium iodide ionic liquid leads to DSCs with a remarkably high JSC value for an N-heterocyclic carbene iron(II) dye of 4.90 mA cm-2, but a low VOC of 244 mV. Our investigations have shown that an increased concentration of Li+ in combination with an optimized alkyl chain length in the 1-alkyl-3-methylimidazolium iodide IL in the electrolyte leads to iron(II)-sensitized DSC performances comparable with those of containing some copper(I)-based dyes.

Crystal structure of (2,2′-bipyridine-κ 2 N,N′)bis(4-(dimethylamino)phenyldiphenylphosphane-κP)copper(I) tetrafluoroborate, C50H48BCuF4N4P2

C50H48BCuF4N4P2, orthorhombic, Pnma (no. 62), a = 24.166(2) Å, b = 19.5652(18) Å, c = 9.6477(9) Å, Z = 4, V = 4561.6(7) Å3, R gt(F) = 0.0494, wR ref(F 2) = 0.1546, T = 298 K.