Structure–properties relationships in dental adhesives: Effect of initiator, matrix monomer structure, and nano-filler incorporation

Novel hydrogen donors as alternative Co-initiators in model dental resins: A performance analysis

OBJECTIVE

This study evaluated the influence of novel co-initiators on the chemical and physical properties of model dental resins at varying initiator-to-co-initiator ratios.

METHODS

A comonomer blend consisting of 50 wt% bis-GMA, 25 wt% TEGDMA, and 25 wt% HEMA was prepared, incorporating 0.5 wt% camphorquinone (CQ) and 0.5 wt% bis(4-methylphenyl)iodonium hexafluorophosphate (IOD). New co-initiators (HD4, HD1, and MHPTm) were tested against standard tertiary amines (DMAEMA and EDAB) at initiator-to-co-initiator ratios of 1:1 and 1:2, resulting in 10 distinct formulations. The properties analyzed included degree of conversion (DC), rate of polymerization (RP), flexural strength (FS), flexural modulus (E), water sorption (Wsp), and solubility (Wsol). Data for DC, FS, E, and Wsp were analyzed using two-way ANOVA and Tukey's test (α = 0.05), and Sol was analyzed with Kruskal-Wallis and Dunn tests (α = 0.05).

RESULTS

For the 1:1 ratio, DMAEMA, EDAB, HD4 and MHPTm exhibited statistically higher DC values compared to HD1, while DMAEMA and EDAB showed the highest DC at the 1:2 ratio. Similar trends were noted for RP, FS, and E. For Wsp, DMAEMA and HD4 showed the statistically highest levels, whereas HD4 and HD1 had the highest Sol in the 1:1 formulation. Overall, the 1:2 initiator-to-co-initiator ratio improved the properties of the novel hydrogen donors tested compared to 1:1 ratio.

CONCLUSIONS

The novel co-initiators demonstrated promising properties for model resins compared to standard references, with the 1:2 ratio yielding the most favorable results for these alternative hydrogen donors.

Impact of silica nanoparticles incorporation on the properties of resin infiltration: an in vitro study

BACKGROUND

This study evaluated the effect of nano-silica (NS) incorporation with resin infiltrant on water sorption and solubility of resin infiltrant, mineral density of demineralized enamel, and resin tags penetration.

METHODS

NS (Sigma-Aldrich, St Louis, Missouri, USA) was added into the resin infiltrant (ICON, DMG, Hamburg, Germany) at two concentrations by weight. The tested groups were: ICON (control), ICON + 0.2, and ICON + 0.5 (n = 10 per group). Water sorption and solubility were assessed using mass variation after 60 days water storage. Mineral density and surface topography were assessed using micro-Computed Tomography scans. Resin tags penetration was measured using a scanning electron microscope. Data were analyzed using one-way Analysis of Variance and Tukey's post-hoc tests (P < .05).

RESULTS

ICON revealed the highest water sorption, solubility mean values (28.90, 7.61) followed by ICON + 0.2 (14.80, 4.82) and ICON + 0.5 (12.32, 0.81) respectively, and vice versa for resin tags penetration. Mineral density of demineralized enamel significantly increased after treatment with ICON + 0.2 and ICON + 0.5.

CONCLUSION

Incorporation of NS to resin infiltrant decreased its water sorption and solubility along with enhancing the mineral density of the demineralized enamel and the penetration of resin tags.

Physicochemical and biological properties of dental materials and formulations with silica nanoparticles: A narrative review

OBJECTIVE

Silica nanoparticles (SNPs) have been extensively studied and used in different dental applications to promote improved physicochemical properties, high substance loading efficiency, in addition to sustained delivery of substances for therapeutic or preventive purposes. Therefore, this study aimed to review the SNPs applications in nanomaterials and nanoformulations in dentistry, discussing their effect on physicochemical properties, biocompatibility and ability to nanocarry bioactive substances.

DATA RESOURCES

Literature searches were conducted on PubMed, Web of Science, and Scopus databases to identify studies examining the physicochemical and biological properties of dental materials and formulations containing SNPs. Data extraction was performed by one reviewer and verified by another STUDY SELECTION: A total of 50 were reviewed. In vitro studies reveal that SNPs improved the general properties of dental materials and formulations, such as microhardness, fracture toughness, flexural strength, elastic modulus and surface roughness, in addition to acting as efficient nanocarriers of substances, such as antimicrobial, osteogenic and remineralizing substances, and showed biocompatibility CONCLUSIONS: SNPs are biocompatible, improve properties of dental materials and serve as effective carriers for bioactive substances CLINICAL SIGNIFICANCE: Overall, SNPs are a promising drug delivery system that can improve dental materials biological and physicochemical and aesthetic properties, increasing their longevity and clinical performance. However, more studies are needed to elucidate SNPs short- and long-term effects in the oral cavity, mainly on in vivo and clinical studies, to prove their effectiveness and safety.

Design of Unconventional Polymers with Thermal Contraction Units for High-Performance Dental Adhesives

The coefficient of thermal expansion (CTE) of adhesives is considered to be a vital parameter for dental restoration due to the oral temperature fluctuation induced by hot and cold drinks in daily life. Even more challenging, the adhesives need to bond various materials with different CTE values, and mismatched thermal expansion at the interface of two materials will produce thermal stress and cause cracking, leading to bond failure. In this study, we designed and synthesized a divinyl monomer containing a dibenzocyclooctadiene (DBCOD) unit, which was incorporated into a commercial adhesive, Single Bond Universal (SBU) to prepare low CTE adhesives. The CTE value of the adhesives can be adjusted low to 6.5 ppm/K, which is much lower than that of pure SBU. Mimicking the real applying conditions, the composite resin columns were bonded to the zirconia ceramics as a dental crown with our designed adhesives, and the shear bond strength test was carried out before and after 10 000 thermal cycles between 5 and 55 °C. The shear bond strength of pure SBU retains 44.7% of its original value after 10 000 thermal cycles, while those low CTE adhesives retain 74.6% and 61.9% of shear bond strength due to less deformation and interfacial stress during thermocycling. The newly designed adhesives provide a persistent way to enhance the shear bond strength and achieve a long lifetime in tooth restoration.

Multi-acrylamides improve bond stability through collagen reinforcement under physiological conditions

OBJECTIVES

Acrylamides were shown to significantly improve bonding stability in adhesive restorations, but the reinforcement mechanism has not been fully elucidated. We tested the hypothesis that hydrogen bonding reinforcement of the collagen network (with secondary or tertiary acrylamides), as well as degree of crosslinking of the polymer network (with di- or tri-functional acrylamides), can be two of the factors at play.

METHODS

Two-step total etch adhesives comprising UDMA (60 wt%) and 40 wt% of: TAAEA, TMAAEA (secondary, tertiary tri-acrylamides), BAAP, DEBAAP (secondary, tertiary di-acrylamides) or HEMA (mono-methacrylate - control) were formulated. Simulated composite restorations (n = 5) were tested after cyclic mechanical and biological (S. mutans biofilm) challenges. Gap formation before and after aging was assessed with SEM imaging. Micro-tensile bond strength (μTBS, n = 6) was assessed after seven-day incubation in water or S. mutans-containing culture medium. Collagen reinforcement was assessed with hydroxyproline assay (n = 10) and rheology (n = 3). Data were analyzed with one-way/two-way ANOVA/Tukey's test (alpha=5%).

RESULTS

Gap formation increased and bond strength decreased for all monomers after biofilm incubation (p < 0.001). Except for DEBAAP, secondary and tertiary di/tri-acrylamides showed lower occlusal gap width values, but no significant differences overall gap length compared to HEMA. μTBS increased for tri-acrylamides compared with HEMA. Samples treated with multi-acrylamides had lower concentration of hydroxyproline (by-product of collagen degradation) (p < 0.001), except for DEBAAP, which showed values close to HEMA (p > 0.05). Dentin shear modulus increased for all acrylamides after 72 h, especially TMAAEA.

SIGNIFICANCE

In general, multi-acrylamides promote collagen reinforcement, leading to reduced gap formation, and stabilize the bond strength under physiological conditions.

Filler Mixed Into Adhesives Does Not Necessarily Improve Their Mechanical Properties

OBJECTIVES

To investigate the influence of filler type/loading on the micro-tensile fracture strength (μTFS) of adhesive resins, as measured 'immediately' upon preparation and after 1-week water storage ('water-stored').

METHODS

The morphology and particle-size distribution of three filler particles, referred to as 'Glass-S' (Esschem Europe), 'BioUnion' (GC), and 'CPC_Mont', were correlatively characterized by SEM, TEM, and particle-size analysis. These filler particles were incorporated into an unfilled adhesive resin ('BZF-29unfilled', GC) in different concentrations to measure the 'immediate' μTFS. After 1-week water storage, the 'water-stored' μTFS of the experimental particle-filled adhesive resins with the most optimum filler loading, specific for each filler type, was measured. In addition, the immediate and water-stored μTFS of the adhesive resins of three experimental two-step universal adhesives based on the same resin matrix but varying for filler type/loading, coded as 'BZF-21' (containing silica and bioglass), 'BZF-29' (containing solely silica), and 'BZF-29_hv' (highly viscous with a higher silica loading than BZF-29), and of the adhesive resins of the gold-standard adhesives OptiBond FL ('Opti-FL', Kerr) and Clearfil SE Bond 2 ('C-SE2', Kuraray Noritake) was measured along with that of BZF-29unfilled (GC) serving as control/reference. Statistics involved one-way and two-way ANOVA followed by post-hoc multiple comparisons (α<0.05).

RESULTS

Glass-S, BioUnion, and CPC_Mont represent irregular fillers with an average particle size of 8.5-9.9 μm. Adding filler to BZF-29unfilled decreased μTFS regardless of filler type/loading. One-week water storage reduced μTFS of all adhesive resins except BZF-21, with the largest reduction in μTFS recorded for BZF-29unfilled. Among the three filler types, the μTFS of the 30 wt% Glass-S and 20 wt% BioUnion filled adhesive resin was not significantly different from the μTFS of BZF-29unfilled upon water storage.

CONCLUSIONS

Adding filler particles into adhesive resin did not enhance its micro-tensile fracture strength but appeared to render it less sensitive to water storage as compared to the unfilled adhesive resin investigated.

Effect of Immediate Dentin Sealing on the Bonding Performance of Indirect Restorations: A Systematic Review

The popular immediate dentin sealing (IDS) technique is used to improve the bond strength of indirect restorations. This systematic review assessed whether bond strength is affected by the type of aging conditions, bonding agents, flowable resin composites, impression materials, temporary materials, and/or resin cement used within the IDS procedure. A comprehensive database search of PubMed, Embase, Scopus, Ovid Medline, Web of Sciences, Cochrane Library, Dentistry & Oral Sciences Source, and ProQuest was carried out up to 30 January 2024 without publication year or language limitations. Only in vitro full-texts regarding the effect of IDS on bond strength were included, and the quality of their methods was assessed via a Risk of Bias (RoB) test. In total, 1023 pertinent studies were initially found, and 60 articles were selected for review after screening for the title, abstract, and full texts. IDS application improves the bond strength of indirect restorations to dentin and reduces the negative effects of temporary materials on the bond durability of final indirect restorations. Filled dentin bonding agents or combinations with flowable resin composite are preferred to protect the IDS layer from conditioning procedures.

Effect of Modified Triple-Layer Application on the Bond Strength of Different Dental Adhesive Systems to Dentin

The goal of this article was to assess the effect of modified triple-layer application (MTLA) in conjunction with the active bonding technique on the bond strength of four adhesive systems to dentinal substrate. The adhesives tested were Prime&Bond Universal (PBU), OptiBond Universal (OBU), OptiBond FL (OBFL), and Clearfil SE (CSE). The adhesives were applied according to the following strategies: single active application (A) and triple adhesive layer application including Active-Passive-Passive (APP); AAP; and AAA. The micro-tensile bond strength test was evaluated following 24 h or 6 months of storage. The composite-dentin interface morphology was investigated using scanning electron microscopy. The data were statistically analyzed with a significance level of α = 0.05. At 24 h of aging, all of the factors tested were not significant (p > 0.05) for CSE. For OBFL, OBU, and PBU, statistically higher values were observed for the A technique (p < 0.05). Plus, there were no significant variances between the APP, AAP, and AAA techniques (p > 0.05) for OBFL and PBU. However, for OBU, there were no significant differences between the A and AAA techniques (p > 0.05). After 6 months of aging, the A technique showed statistically higher values when compared to the other techniques (p < 0.01), except for OBFL, where the A and AAA techniques showed promising outcomes. When comparing the bond strength values of 24 h and 6 months, only for PBU, all of the techniques used resulted in bond strength stability over time (p > 0.05). Thicker adhesive layers were observed when MTLA was applied. Only the OBFL adhesive showed the formation of resin tags in all of the modalities tested. The bonding performances of the different application techniques used were material-dependent.

Synthesis, characterization, photo-polymerization, hydrolytic stability, and etching behavior of new self-etch adhesive monomers

Considering the poor hydrolytic stability of the most methacrylate-based functional monomers of self-etch dental adhesives in acidic and aqueous conditions, in this study allyl-based photo-polymerizable self-etch monomers was synthesized in order to improve the hydrolytic stability. The new self-etch monomers based on phosphonic acid functional groups were synthesized through a two-step procedure. First, phosphoric anhydride, poly-phosphoric acid, and polyethylene glycol were reacted to produce phosphate ester precursor (P-PEG-P). Next, allyl 2, 3-epoxypropyl ether was reacted with P-PEG-P to synthesize allyl self-etch monomer. Glycidyl methacrylate was also reacted with P-PEG-P to synthesize a methacrylate self-etch analogue monomer. The monomers were characterized using FTIR and 1H-NMR spectroscopy. The viscosities of monomers were measured using a rheometer. The degree photopolymerization conversion of monomers was measured using FTIR spectroscopy. The pH assay was performed by a digital pH-meter. The etching behavior of the monomers on human teeth was studied using scanning electron microscopy (SEM). Thermo-gravimetric analysis (TGA) was performed to evaluate the possible interaction of the monomers with tricalcium phosphate (TCP). The solubility of synthesized monomers was examined in ethanol, acetone, and water. The hydrolytic stability of cured resins in artificial saliva during 4 months was also surveyed. The synthesis of new self-etching monomers was successfully confirmed by spectroscopy analyses. The results represented appropriate viscosity of self-etching monomers around 1 (Pa s). The resin containing methacrylate monomer exhibited its degree of conversion is more than that of allyl monomer (p < 0.05). The allyl and methacrylate self-etch monomers exhibited pH values of 1.2 and 1.3, respectively. SEM micrograph verified that the synthesized monomers were able to suitable etching of the enamel human premolar teeth. The data obtained from TGA tests revealed that thermal stability of (TCP) containing monomers is enhanced. Also, the monomers exhibited an excellent solubility in polar solvents, but when they are mixed with TCP, they are not, anymore, dissolved in these solvents. Furthermore, the allyl monomer showed higher hydrolytic stability than the methacrylate monomer. The new photo-polymerizable acidic monomer based on allyl functionality showed enhanced hydrolytic stability compared to methacrylate-based monomer. It may be considered as a promising monomer for self-etch dental adhesives.

L-arginine-containing mesoporous silica nanoparticles embedded in dental adhesive (Arg@MSN@DAdh) for targeting cariogenic bacteria

Dental caries is the major biofilm-mediated oral disease in the world. The main treatment to restore caries lesions consists of the use of adhesive resin composites due to their good properties. However, the progressive degradation of the adhesive in the medium term makes possible the proliferation of cariogenic bacteria allowing secondary caries to emerge. In this study, a dental adhesive incorporating a drug delivery system based on L-arginine-containing mesoporous silica nanoparticles (MSNs) was used to release this essential amino acid as a source of basicity to neutralize the harmful acidic conditions that mediate the development of dental secondary caries. The in vitro and bacterial culture experiments proved that L-arginine was released in a sustained way from MSNs and diffused out from the dental adhesive, effectively contributing to the reduction of the bacterial strains Streptococcus mutans and Lactobacillus casei. Furthermore, the mechanical and bonding properties of the dental adhesive did not change significantly after the incorporation of L-arginine-containing MSNs. These results are yielding glimmers of promise for the cost-effective prevention of secondary caries.

Comparative Assessment of Different Pre-Treatment Bonding Strategies to Improve the Adhesion of Self-Adhesive Composites to Dentin

The aim of this study is to compare the adhesive interface formed in dentin, using self-adhesive composites applied with different bonding strategies, by testing the microtensile bond strength (μTBS) and ultramorphology through the use of light microscopy. Permanent, sound human molars were randomly allocated to six experimental groups. The groups included a negative control group, where only etching was performed via EtchOnly; a positive control group where an adhesive was applied, OptiBondFL (OBFL); and an experimental group where a primer was applied using a co-curing strategy together with a composite (Primer_CoCuring). The samples were sectioned into microspecimens for μTBS (n = 8) and into 1-mm thick slabs for light microscopy using Masson’s trichrome staining protocol (n = 3). The statistical analysis included a two-way ANOVA for μTBS data and Tukey’s HSD was used as a post-hoc test (significance level of 5%; SPSS v. 26.0). The results of the μTBS revealed that the self-adhesive composite (F = 6.0, p < 0.018) and the bonding strategy (F = 444.1, p < 0.001) significantly affected the bond strength to dentin. However, their interactions were not significant (F = 1.2, p = 0.29). Etching dentin with no additional treatment revealed the lowest μTBS (VF_EtchOnly = 2.4 ± 0.8 MPa; CC_EtchOnly = 2.0 ± 0.4 MPa), which was significantly different from using a primer (VF_CoCu = 8.8 ± 0.8 MPa; CC_CoCu = 6.3 ± 1.0 MPa) or using the full adhesive (VF_OptiBondFL = 22.4 ± 0.3 MPa; CC_OptibondFL = 21.2 ± 0.4 MPa). Microscopy images revealed that the experimental Primer_CoCuring was the only group with no collagen fibers exposed to the dentin−composite interface. Overall, the use of a primer, within the limitations of this study, increased the bonding of the self-adhesive composite and provided sufficient infiltration of the collagen based on light-microscopic imaging.

Compressive strength of premolars restored with ceramic crowns and supported with a glass fiber post using different luting agents

Objective

The retention of glass fiber post (GFP) is considered a key factor for the long-term success of restorations of endodontically treated teeth. This study aimed to compare the compressive strength of a ceramic crown supported by a GFP using different luting agents.

Methods

Forty single-rooted premolars were randomly divided into four groups (n = 10 each): control group (teeth without a GFP), Ketac Cem group (glass ionomer), RelyX ARC group (conventional dual-curing resin), and RelyX U200 group (self-adhesive dual-curing resin). After luting of the posts and placement of all-ceramic crowns made using feldspathic porcelain (Noritake EX-3), they were exposed to thermocycling for 1000 cycles and compressive strength tests. Statistical analysis included Kruskal–Wallis test with Dunn’s multi-comparison test.

Results

The Ketac Cem group and RelyX U200 group showed significantly greater fracture resistance to compressive loading than the control group.

Conclusion

This study indicates a possible role of the luting agent used with the GFP in influencing the compressive strength of the restored teeth. In this study, the self-adhesive dual-curing resin and glass ionomer both offered resistance to fractures.

Development of low-shrinkage dental adhesives via blending with spiroorthocarbonate expanding monomer and unsaturated epoxy resin monomer

Polymerization shrinkage is one of the main drawbacks of dental resin adhesives. In this study, spiroorthocarbonate expanding monomer 3,9-diethyl-3,9-dimethylol -1,5,7,11-tetraoxaspiro-[5,5] undecane (DDTU) and unsaturated epoxy resin monomer Diallyl bisphenol A diglycidyl ether (DBDE) were synthesized and utilized as anti-shrinkage-coupling additive of methacrylate-based adhesives. Polymerization process and physicochemical properties including double bond conversion, polymerization shrinkage, compatibility, mechanical performance, thermal stability, contact angle, shear bond strength and cytotoxicity were characterized. Results indicated that adhesives containing anti-shrinkage-coupling additive had reduced volume shrinkage, improved compatibility and enhanced shear bond strength. When the amount of additive was 20 wt%, the volume shrinkage was decreased by 45.8% (4.17 ± 0.32%) and the shear bond strength was increased by 49.6% (19.64 ± 0.99 MPa). The results also showed that the use of additive had no adversely affect on double bond conversion and cytotoxicity. Therefore, novel low-shrinkage resin adhesives were prepared via blending with spiroorthocarbonate expanding monomer and unsaturated epoxy resin monomer.

Interaction of zirconium oxide nanoparticle infiltrated resin adhesive with dentin conditioned by phosphoric acid and Er, Cr: YSGG laser

The aim was to prepare experimental adhesive (EA) with ZrO₂ nanoparticles (ZEA) and without it; and its interaction with dentin conditioned with photodynamic therapy (PDT), etch and rinse, and Er, Cr: YSGG laser (ECL). Methods consisted of the scanning electron microscope (SEM), energy dispersive X-ray (EDX), shear bond strength (SBS) failure mode, and rheological property analysis. The methods were employed to assess bond integrity; the shape of ZrO₂ NPs and interfacial dentin and adhesive interaction. Ninety premolar teeth were collected and pre-bonding, conditioning of dentin was performed utilizing phosphoric acid (H3PO4), photodynamic therapy (PDT), and ER-CR-YSGG laser (ECL). The teeth were set to form bonded specimens using two adhesives EA and ZEA. The microscopic imagery of ZrO₂ revealed irregular-shaped, non-edged particles. EDX analysis revealed Zr to be 75.7% whereas, O2 by weight was 25.3%. The highest SBS was demonstrated in dentin conditioned with etch and rinse and ZEA (19.05 ± 0.13 MPa). Whereas, the lowest SBS was observed in dentin surface treated with PDT and EA (12.25 ± 0.14 MPa). Most of the reported failure modes were adhesive. Rheological analysis revealed that with increasing frequencies the viscosities of adhesives were reduced. The presence of 10% ZrO by weight in adhesive improves SBS of restoration and this improvement in bond values is statistically significant compared to EA. Bond values may be influenced by surface treatment of dentin.

Physical/Mechanical and Antibacterial Properties of Orthodontic Adhesives Containing Calcium Phosphate and Nisin

Enamel demineralization around orthodontic adhesive is a common esthetic concern during orthodontic treatment. The aim of this study was to prepare orthodontic adhesives containing monocalcium phosphate monohydrate (MCPM) and nisin to enable mineralizing and antibacterial actions. The physicomechanical properties and the inhibition of S. mutans growth of the adhesives with added MCPM (5, 10 wt %) and nisin (5, 10 wt %) were examined. Transbond XT (Trans) was used as the commercial comparison. The adhesive containing a low level of MCPM showed significantly higher monomer conversion (42–62%) than Trans (38%) (p < 0.05). Materials with additives showed lower monomer conversion (p < 0.05), biaxial flexural strength (p < 0.05), and shear bond strength to enamel than those of a control. Additives increased water sorption and solubility of the experimental materials. The addition of MCPM encouraged Ca and P ion release, and the precipitation of calcium phosphate at the bonding interface. The growth of S. mutans in all the groups was comparable (p > 0.05). In conclusion, experimental orthodontic adhesives with additives showed comparable conversion but lesser mechanical properties than the commercial material. The materials showed no antibacterial action, but exhibited ion release and calcium phosphate precipitation. These properties may promote remineralization of the demineralized enamel.

Non-thermal plasma for surface treatment of inorganic fillers added to resin-based cements

OBJECTIVES

This study aims to evaluate the effect of non-thermal plasma (NTP) surface treatment in two composite inorganic fillers and evaluate their impact on the chemical-mechanical properties and bond strength ability of experimental resin cements.

MATERIALS AND METHODS

Ytterbium fluoride (YF) and barium silicate glass (BS) were characterized and submitted to different surface treatments: non-thermal plasma (NTP); non-thermal plasma and 3-(trimethoxysilyl) propyl methacrylate silanization; and 3-(trimethoxysilyl) propyl methacrylate silanization. Untreated fillers were used as a control. The fillers were incorporated at 65wt% concentration into light-cured experimental resin cements (50wt% BisGMA; 25wt% UDMA; 25wt% TEGDMA; 1mol% CQ). The degree of conversion, the flexural strength, and the microshear bond strength (μSBS) were evaluated to characterize developed composites.

RESULTS

YF and BS were successfully cleaned with NTP treatment. Nor NTP neither the silanization affected the degree of conversion of resin cements. The NTP predicted an increase in YF-containing resin cements flexural strength, reducing the storage impact in these materials. NTP treatment did not affect the μSBS when applied to YF, while silanization was effective for BS-containing materials.

CONCLUSION

NTP treatment of inorganic particles was possible and was shown to reduce the amount of organic contamination of the particle surface. YF surface treatment with NTP can be an alternative to improve the organic/inorganic interaction in resin composites to obtain materials with better mechanical properties.

CLINICAL RELEVANCE

Surface cleaning with NTP may be an alternative for particle surface cleaning to enhance organic-inorganic interaction in dental composites resulting in improved mechanical strength of experimental resin cements.

Visible-Light-Sensitive Triazine-Coated Silica Nanoparticles: A Dual Role Approach to Polymer Nanocomposite Materials with Enhanced Properties

Nanocomposite materials are of great interest because of their superior properties. Besides the traditional synthesis methods that require high temperatures or toxic solvents, photopolymerization technology provides a simple, low-cost, and environmentally friendly route in preparing nanocomposites. In this research, the preparation of blue-light-sensitive triazine derivative-coated silica nanoparticles is presented. The resulting triazine-coated silica nanoparticles can play a dual role, i.e., acting as both photoinitiators to trigger photopolymerization reactions under the irradiation of LED@410 nm and fillers to endow the produced photopolymer nanocomposite materials with enhanced properties. Specifically, the triazine-coated silica nanoparticles can successfully induce free radical polymerization of trimethylolpropane triacrylate efficiently under the irradiation of LED@410 nm and demonstrate comparable photoinitiation ability to the triazine derivative-based photoinitiator. The effects of different loading amounts of triazine-coated silica nanoparticles toward the photopolymerization kinetics are also evaluated. By coating with the triazine derivative, the nanoparticles show good dispersion in the polymer matrix and significantly reduce the shrinkage of the samples during the photopolymerization. Moreover, the photocured nanocomposites exhibit enhanced migration stability and mechanical properties when an optimal amount of triazine-coated silica nanoparticles is added in the formulation.

Shelf Life and Storage Conditions of Universal Adhesives: A Literature Review

This paper presents state of the art universal adhesive systems and the effect of shelf-life and storage conditions on their bond performance. Three topics are explored in this review: an introduction to the topic, the mechanisms responsible for the degradation of the hybrid layer, and the factors that play a role in the stability of universal adhesives. In addition, issues such as potential durability and clinical importance are discussed. Universal adhesive systems are promising but must be handled and stored according to the manufacturer's instructions, with careful attention given to the details of shelf-life and storage conditions for maximal success. It appears that the components of universal adhesives play an important role in their stability. Furthermore, HEMA-free formulations using methacrylamides lead to longer shelf-life. Further research is needed to prove these hypotheses.

Effect of Substituents in Mussel-inspired Surface Primers on their Oxidation and Priming Efficiency

Marine mussels contain an abundant catechol moiety, 3,4-dihydroxyphenylalanine (DOPA), in their interfacial foot proteins. DOPA contributes to both surface adhesion and bridging between the surface and overhead proteins (surface priming) by taking advantage of the unique redox properties of catechol. Inspired by the mussel surface priming mechanism, herein we synthesized a series of DOPA-mimetic analogs - a bifunctional group molecule, consisting of a catechol group and an acrylic group at the opposite ends. The surface primers with differently substituted (-COOH, -CH3 ) alkyl chains in the middle spacer were synthesized. Time-dependent oxidation and redox potentials of the surface primers were studied in an oxidizing environment to gain a better understanding of the mussel's redox chemistry. The thickness and degree of priming of the surface primers on silicon-based substrates were analyzed by ellipsometry and UV/Vis absorption spectroscopy. The post-reactivity of the acrylic groups of the primed layer was first visualized through a reaction with an acrylic group-reactive dye.

In vitro performance of 2-step, total etch adhesives modified by thiourethane additives

OBJECTIVES

Thio-urethane oligomeric additives have been shown to improve the mechanical properties of dental composites and resin cements. To try to harness those same properties in dental adhesives, in this study, these oligomers (TU) were added to the matrix and/or as filler functionalization of experimental adhesives, and the effects on conversion and mechanical properties were analyzed.

METHODS

BisGMA and HEMA (60/40 wt%) were used as the monomer matrix, made polymerizable by the addition of 0.2 wt% 2,2-dimethoxy-2- phenylacetophenone. 2,6-di-tert-butyl-4-methylphenol was added at 0.5 wt% as the inhibitor. This material was used as the unfilled control (BH). TU oligomers were added at 20 wt % to the matrix (BH+20%TU, unfilled) and/or used as filler functionalization (TF, 10 wt%). Fillers functionalized with methacrylate (MF, 10 wt%) served as the control. The experimental adhesives groups containing fillers were: BH+10%MF; BH+10%TF; BH+20%TU+10%MF; BH+20%TU+10%TF. Flexural properties were tested in three-point bending (wet and dry). Polymerization kinetics was followed in real-time in near-IR. Water Sorption/Solubility (WS/SL, ISO 4049) and Viscosity (rotational rheometry) were also evaluated. For Microtensile bond strength 40 vol% ethanol was added to adhesives, which was applied onto sound dentin from third human molars. The data were analyzed with one-way ANOVA and Tukey post-hoc test, and test t for the comparison between storage time of the microtensile bond strength test (alpha = 0.05).

RESULTS

There was no significant difference between groups when yield strength (YS) and flexural modulus (FM) were evaluated in dry conditions. After water storage, all the groups containing TU in the matrix showed statistically lower YS/FM values. This was true in spite of the statistically higher conversion for those same groups. The maximum rate of polymerization (Rpmax) was higher for BH+10%TF and no significant difference was found for the groups BH and BH+10% MF. The lowest Rpmax values were found for BH+20%TU+10%TF and BH+20%TU. BH+20%TU+10%TF showed the highest viscosity values followed by BH+20%TU+10%MF and BH+20%TU, with statistically significant difference between them. For the microtensile bond strength test at 24h (p = 0.13) and 6 months (p = 0.11) and WS/SL (p > 0.05), no significant difference was found among groups. The storage time (24 h and 6 months) did not affect the microtensile bond strength results.

CONCLUSION

In spite of improving the conversion, the addition of TU in the matrix reduced the mechanical properties of the adhesives tested after water storage. This did not affect the bond strength at 24 h or 6 months.

Dental Adhesive Interfaces Reinforced with Magnetic Nanoparticles: Evaluation and Modeling with Micro-CT versus Optical Microscopy

Dental adhesives are used in a wide range of applications, including to place direct composite restorations in frontal or posterior teeth. One of the most frequent causes for the failure of composite resin restorations is microleakages. The first aim of this work is to introduce a new type of self-etched dental adhesive doped with magnetic nanoparticles (MPs) synthetized in the laboratory. The scope is to produce adhesives with a minimized width/thickness to decrease the risk of microleakages. The second aim is to assess the width/thickness of the adhesive layer in all the characteristic areas of the teeth using both the less precise but most common optical microscopy and the more accurate and volumetric micro-Computed Tomography (CT) investigations. Twenty extracted teeth have been divided into four groups: Group 1 includes 'blank' samples with adhesives that are not doped with MPs; Group 2 includes samples with adhesives doped with MPs; Groups 3 and 4 include samples with adhesives doped with MPs that are subjected to an active magnetic field for 5 and 10 min, respectively. Microscopy investigations followed by micro-CT and EDAX are performed on the adhesive. While a rather good agreement is obtained between the microscopy and micro-CT results, the capability of the latter to offer a full volumetric reconstruction of the layer is exploited to analyze the adhesion of the four considered dental materials. Thus, from micro-CT results the graphs of the surface areas as functions of the adhesive layer width are modeled mathematically, as well as the volume of sealants, for each of the four groups. To our knowledge, it is the first time that such a methodology is used. Characteristic parameters are extracted and the ascertainment of the optimal parameter that should be utilized for such assessments is discussed. The study demonstrates the adhesion improvement produced for Groups 3 and 4, where MPs are used. It also concludes that the magnetic field should be applied to the adhesive material for the longest possible exposure time (with a trade-off with the clinical duration of the treatment).

Dual modified nanosilica particles as reinforcing fillers for dental adhesives: Synthesis, characterization, and properties

A facile procedure has been devised to develop a novel dentin bonding system containing poly (acrylic acid)-grafted-silanized fumed silica particles as reinforcing filler, with high stability of nanoparticle dispersion and enhanced bond strength and mechanical properties. In the first step, the silanization of fumed silica nanoparticles was performed in the following conditions: (i) ethanol-water solution with a pH of 5 and (ii) cyclohexane with a pH of 9 using trimethoxysilylpropyl methacrylate (γ-MPS) as a reactive silane coupling agent. FTIR and TGA analyses confirmed the presence of silane in the resultant structure and enhanced dispersion stability of modified particles was proved by a separation analyzer and also zeta potential analyses. In the second step, free radical polymerization of acrylic acid monomers in the presence of silanized nanoparticles was carried out and poly (acrylic acid) -grafted- silanized fumed silica were acquired. The flexural strength and fracture toughness of the adhesive containing 0.2 wt.% of the dual modified filler reached maximum of 70.4 MPa and 1.34 MPa m^1/2, respectively, showing average improvements of 74% and 179%, respectively, in comparison with the adhesive without filler. Flexural modulus values did not significantly change with increasing the filler content except the adhesive containing 5 wt.% having the lowest flexural modulus. The highest microtensile bond strength was also observed at 0.2 wt.% filler content showing the average improvements of 197% as compared with the neat adhesive. Energy dispersive X-ray (EDX) mapping confirmed a homogenous and uniform distribution of the fillers in the adhesive matrix containing 0.2 wt.% and 0.5 wt.% of filler while incorporation of 5 wt.% led to large particle aggregates. SEM images of the fracture surface of the adhesive with different filler contents subjected to fracture toughness test showed rougher surface and longer crack path by increasing filler concentration. The adhesive containing 0.2 wt.% of filler perfectly penetrated into the dentin tubules proved by the SEM micrographs in microtensile bond strength test.

Applications of nano-materials in diverse dentistry regimes

Research and development in the applied sciences at the atomic or molecular level is the order of the day under the domain of nanotechnology or nano-science with enormous influence on nearly all areas of human health and activities comprising diverse medical fields such as pharmacological studies, clinical diagnoses, and supplementary immune system. The field of nano-dentistry has emerged due to the assorted dental applications of nano-technology. This review provides a brief introduction to the general nanotechnology field and a comprehensive overview of the synthesis features and dental uses of nano-materials including current innovations and future expectations with general comments on the latest advancements in the mechanisms and the most significant toxicological dimensions.

The influence of nanofillers on the properties of ethanol-solvated and non-solvated dental adhesives

Objectives

The aim of this study was to evaluate the influence of different concentrations of nanofillers on the chemical and physical properties of ethanol-solvated and non-solvated dental adhesives.

Materials and Methods

Eight experimental adhesives were prepared with different nanofiller concentrations (0, 1, 2, and 4 wt%) and 2 solvent concentrations (0% and 10% ethanol). Several properties of the experimental adhesives were evaluated, such as water sorption and solubility (n = 5, 20 seconds light activation), real-time degree of conversion (DC; n = 3, 20 and 40 seconds light activation), and stability of cohesive strength at 6 months (CS; n = 20, 20 seconds light activation) using the microtensile test. A light-emitting diode (Bluephase 20i, Ivoclar Vivadent) with an average light emittance of 1,200 mW/cm² was used.

Results

The presence of solvent reduced the DC after 20 seconds of curing, but increased the final DC, water sorption, and solubility of the adhesives. Storage in water reduced the strength of the adhesives. The addition of 1 wt% and 2 wt% nanofillers increased the polymerization rate of the adhesives.

Conclusions

The presence of nanofillers and ethanol improved the final DC, although the DC of the solvated adhesives at 20 seconds was lower than that of the non-solvated adhesives. The presence of ethanol reduced the strength of the adhesives and increased their water sorption and solubility. However, nanofillers did not affect the water sorption and strength of the tested adhesives.

Color stability of Lucirin-photo-activated resin composite after immersion in different staining solutions: a spectrophotometric study

INTRODUCTION

Exceptional optical properties characterize teeth. As such, an esthetic restorative material should enable the dental professional to imitate the optical properties of natural teeth accurately. IPS Empress Direct was introduced to the market with the claim that it can mimic optically dental tissues with superior clinical performance.

AIM

To evaluate the ability of IPS Empress Direct to mimic tooth appearance and color and resist staining.

MATERIALS AND METHODS

Three disc specimens were prepared for each shade of enamel and dentin of Lucirin-based composite, IPS Empress Direct (Ivoclar Vivadent) (A1, A2, A3, B1, and B2) (total of 60). The specimens were submitted to colorimetric evaluation in comparison after immersion in 10 different solutions (coffee, coffee with sugar, coffee with milk, red tea, red tea with sugar, red tea with milk, tomato juice, pomegranate juice, coke, and distilled water as a control group) for 4 weeks using spectrophotometric analysis.

RESULTS

After plotting the data and conducting linear regression analyses, IPS Empress showed high potential in mimicking the optical properties of natural tooth color according to the CIE color space. Three solutions showed a change in color higher than 3, coffee, coffee with sugar, and red tea. All other solution showed changes in color that are acceptable clinically.

CONCLUSION

IPS Empress Direct can satisfactory mimic teeth appearance and color while manifesting high stability of color resisting staining upon clinical aging.

Adhesive Systems Used in Indirect Restorations Cementation: Review of the Literature

New technologies are changing the therapeutical options to do indirect restorations and new adhesive systems are continuously introduced to be used by clinicians. Different interactions between restorations, adhesive systems components, enamel and dentin require having criteria based on the selection of the adhesive system, ensuring the longevity of the restorations and the preservation of the biological remnant. The adhesion force to the dental tissue is one of the indicatives of the behavior of the adhesive systems and influences the behavior of the treatments with direct and indirect restorations. The objective of this search was to find the adhesive systems with the best results in terms of the adhesion strength of indirect restorations on the dental tissues. The search was conducted in two MEDLINE digital databases (PubMed), and the Cochrane Library with a search strategy based on the combination of MeSH (Medical Subject Headings) keywords. This systematic review used the PRISMA guide (Preferred Reporting Items for Systematic Reviews and Meta-Analysis). According to this review, the 3-step adhesive systems were the best performing and still are the gold standard for the cementing of indirect restorations. In addition, it can be concluded that self-etched adhesive systems reduce the time spent in clinical practice, however at the interface level they behave as permeable membranes more susceptible to degradation.

Examining the Effect of Radiant Exposure on Commercial Photopolimerizable Dental Resin Composites

The objective of this study was to evaluate the effect of radiant exposure on the chemical and physical properties of four commercial dental resin composites. The four dental resin composites used were Kalore, Admira, Tetric N-Ceram Bulk Fill, and Filtek Z350 XT. The composites were subjected to three curing protocols: 1000 mW/cm² for 5 s, 1000 mW/cm² for 10 s, and 400 mW/cm² for 25 s. The flexural strength, elastic modulus, water sorption, water solubility, degree of conversion, and polymerization shrinkage were evaluated. The results were analyzed by means of ANOVA and Tukey tests. For Admira and Kalore, significant differences between light exposure protocols were observed for the elastic modulus (p < 0.001), which was higher when a higher amount of radiant exposure was used. For Filtek Z350, differences were only observed for the degree of conversion (p < 0.001), and a higher amount of radiant exposure allowed us to obtain higher values. The Tetric N-Ceram Bulk Fill analysis showed significant differences for the elastic modulus and water sorption (p < 0.001), and specimens that had been subject to a radiant exposure of 10 J/cm² showed a higher elastic modulus. In most cases, the physical and mechanical properties analyzed were not affected by different radiant exposure values. Other resin-based composite (RBC) characteristics seem to have a greater influence on material properties.