Fabrication of cerium doped Ti/nanoTiO2/PbO2 electrode with improved electrocatalytic activity and its application in organic degradation

A comprehensive review of PbO2 electrodes in electrocatalytic degradation of organic pollutants

This paper provides a systematic review of recent advancements in PbO2 electrodes for the electrocatalytic degradation of organic pollutants, emphasizing innovative breakthroughs and key technological optimizations in this domain. This work analyzes PbO2 electrode fabrication methods, assessing strengths/weaknesses, and summarizes recent advances in surface modification. Atomic-scale strategies such as elemental doping, composite oxides, and nanomaterial coupling, enhance its catalytic performance. Kinetic modeling and characterization confirm the improved efficiency and durability in organic contaminant mineralization. Kinetic and experimental analyses demonstrate the high efficiency and stability of modified PbO2 electrodes in degrading organic pollutants. Industrial feasibility analysis indicates that the PbO2 electrode demonstrates technical robustness, economic viability, and scalability for industrial implementation. This work elucidates direct/indirect oxidation mechanisms in electrocatalysis, revealing correlations between surface reactive sites and active oxidant generation, guiding electrode design optimization. Looking ahead, this paper proposes innovative trajectories for PbO2 electrode technology, such as exploring novel modified materials, intelligently designing hierarchical architectures, and integrating advanced systems with smart control. These directions aim to promote its widespread use in environmental protection for more efficient and eco-friendly organic pollutant treatment. This review enriches the theoretical framework for PbO2 electrode electrocatalytic degradation of organic contaminants and offers references and inspirations for future research.

Electrochemical degradation of Cephalexin on Ti/TiO2/βPbO2 anode modified by sodium dodecyl sulfate

The possible environmental dangers of antibiotics include excessive use, wastewater discharge, and resistance to biodegradability. Therefore, efficient and environmentally friendly methods to remove such pollutants are necessary to preserve global ecosystems and human life. Electrochemical oxidation using lead-based electrodes is an effective approach for the treatment of resistant organic pollutants. In this research, a Ti/TiO2-βPbO2 electrode was synthesized for the electrochemical degradation of Cephalexin. To increase the efficiency and stability of the electrode, βPbO2 electrodeposition was performed in the presence of sodium dodecyl sulfate. The performance of the electrode in the degradation and mineralization of Cephalexin was evaluated using cyclic voltammetry and differential pulse voltammetry, and the maximum degradation efficiency and maximum COD removal of 97.60% and 70.27%, respectively, were obtained. In addition, the degradation mechanism was studied using liquid chromatography coupled with tandem mass spectrometry. The findings indicated that the Ti/TiO2-βPbO2 electrode exhibited desirable electrocatalytic performance in the degradation and mineralization of Cephalexin. Therefore, wastewater contaminated with antibiotic residues can be treated before discharging into the sewage system and the environment by this approach.

Zirconium-doped lead dioxide anodes prepared by sol-gel method for ampicillin removal from simulated pharmaceutical polluted wastewater

New anodes consisting of zirconium-doped PbO2 coating, growth on titanium dioxide interlayer, were deposited on titanium substrates using spin coating method and have been tested for the removal of ampicillin, a β-lactam antibiotic, from water. Morphological, structural, and electrochemical properties of the prepared coatings were characterized by scanning electron microscopy (SEM), atomic force microscope (AFM), X-ray diffraction (XRD), and electrochemical impendence spectroscopy (EIS). Results showed that the incorporation of zirconium dopant had a noticeable modification in the morphology of anodes. An increase in the surface roughness and the specific active area were observed with Ti/TiO2/PbO2- 10% Zr electrode compared to other anodes. The electrochemical measurements indicated that the anode doped with 10% Zr showed a more protective coating performance than the undoped and 20% Zr-doped PbO2 electrodes. The experiments on ampicillin degradation revealed that doped lead dioxide anodes have excellent electrocatalytic activity. The major byproduct generated during anodic oxidation treatment has been identified as ampicilloic acid by liquid chromatography-mass spectroscopy (LC-MS) analysis. Results demonstrated that Ti/TiO2/PbO2- 10% Zr anode presents the best removal rate of ampicillin with a minimum intermediate amount, which leads to conclude that 10% is the optimum percentage of zirconium dopant for antibiotic wastewater treatment.

Electrochemical oxidation of carbamazepine in water using enhanced blue TiO2 nanotube arrays anode on porous titanium substrate

In this study, a blue TiO₂ nanotube arrays anode on porous titanium substrate (Ti-porous/blue TiO₂ NTA) was successfully fabricated by facile anodization and in situ reduction, and was used to investigate the electrochemical oxidation of carbamazepine (CBZ) in aqueous solution. The surface morphology and crystalline phase of the fabricated anode were characterized by SEM, XRD, Raman spectroscopy and XPS, and the electrochemical analysis confirmed that blue TiO₂ NTA on Ti-porous substrate had larger electroactive surface area, better electrochemical performance and higher ⋅OH generation ability than that on Ti-plate substrate. The removal efficiency of 20 mg L^-1 CBZ in 0.05 M Na₂SO₄ solution reached 99.75% at 8 mA cm^-2 after 60 min electrochemical oxidation, and the rate constant was 0.101 min^-1 with low energy consumption. EPR analysis and free radical sacrificing experiments showed that ⋅OH played a key role in the electrochemical oxidation. The possible oxidation pathways of CBZ were proposed through the identification of degradation products, and the main reactions may involve deamidization, oxidization, hydroxylation and ring-opening. Compared with Ti-plate/blue TiO₂ NTA anode, Ti-porous/blue TiO₂ NTA anode displayed excellent stability and reusability, and is promising to be used in the electrochemical oxidation of CBZ in wastewater.

Electrocatalytic degradation of methyl orange and 4-nitrophenol on a Ti/TiO2-NTA/La-PbO2 electrode: electrode characterization and operating parameters

The anode material plays a crucial role in the process of electrochemical oxidation. Herein, a TiO₂ nanotube arrays (TiO₂-NTA) intermediate layer and La-PbO₂ catalytic layer were synthesized on a Ti surface by the electrochemical anodic oxidation and electrochemical deposition technology, respectively. The prepared Ti/TiO₂-NTA/La-PbO₂ electrode was used as an electrocatalytic oxidation anode for pollutant degradation. Scanning electron microscopy (SEM) analysis showed that the TiO₂-NTA layer possessed a highly ordered and well-aligned nanotube array morphology, and the La-PbO₂ layer with angular cone cluster was uniform and tightly bonded. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analysis indicated that the intermediate layer primarily consisted of the anatase crystal structure of TiO₂ and the catalyst layer was made of La-PbO₂. Electrochemical analysis revealed that Ti/TiO₂-NTA/La-PbO₂ electrode exhibited higher oxidation peak current, electrochemical active surface area, and oxygen evolution potential (OEP, 1.64 V). Using methyl orange and 4-nitrophenol as model pollutants, electrocatalytic properties of the prepared Ti/TiO₂-NTA/La-PbO₂ electrode were systematically investigated under different conditions, and the electrochemical degradation fitted well with the pseudo-first-order kinetics model. Efficient anodic oxidation of model pollutants was mainly attributed to the indirect oxidation mediated by hydroxyl radicals (•OH). The total organic carbon (TOC) removal efficiency of methyl orange and 4-nitrophenol was 70.2 and 72.8%, and low energy consumption (2.50 and 1.89 kWh g^-1) was achieved after 240 min of electrolysis under the conditions of initial concentration of model pollutant, electrode spacing, and electrolyte concentration were 50 mg L^-1, 2 cm, and 0.1 mol L^-1, respectively. This work provided a new strategy to develop the high-efficiency electrode for refractory pollutants degradation.

When MXene (Ti3C2Tx) meet Ti/PbO2: An improved electrocatalytic activity and stability

Stable electrode materials with high catalytic activity are urgently required for electrochemical degradation of refractory organic pollutants in wastewater treatment. Herein, high conductive MXene (Ti₃C₂T_x) was firstly fabricated by electrophoretic deposition (EPD) as an interlayer for preparing a novel PbO₂ electrode. The well-conducted Ti₃C₂T_x interlayer significantly improved the electrochemical performance of the EPD-2.0/PbO₂ (EPD time was 2.0 min) electrode with the charge transfer resistance decreased by 9.51 times, the inner active sites increased by 5.21 times and the ∙OH radicals generation ability enhanced by 4.07 times than the control EPD-0/PbO₂ anode. Consequently, the EPD-2.0/PbO₂ electrode achieved nearly 100% basic fuchsin (BF) and 86.78% COD removal efficiency after 3.0 h electrolysis. Therefore, this new PbO₂ electrode presented a promising potential for electrochemical degradation of BF and the new Ti₃C₂T_x middle layer could also be used to fabricate other efficient and stable anodes, such as SnO₂, MnO₂, TiO₂, etc.

Electrochemical Oxidation of Methyl Orange in an Active Carbon Packed Electrode Reactor (ACPER): Degradation Performance and Kinetic Simulation

The efficient removal and kinetic modelling of methyl orange (MO) degradation using an electrocatalytic oxidation method in an activated carbon (AC) packed electrode reactor (ACPER) were conducted. A significantly high (81.2%) chemical oxygen demand (COD) and 100.0% MO decolorization efficiency were observed under the experimental conditions of current density of 3.0 mA·cm⁻², flow velocity of 0.3 L·h⁻¹, and treatment duration of 1.68 h using a β-PbO₂/Ti anode. The high removal efficiency is ascribed to the anode expansion effect after AC packing. The anode expansion coefficient (λ) of the ACPER was calculated to be 0.63 from the cyclic voltammetry (CV) measurement, which means the further current utilization for MO oxidation. Based on the current utilization efficiency on anodic and particle electrode surfaces, a phase-reaction kinetics model was proposed for the simulation of MO COD removal efficiency. Our simulation results showed that the newly established average current efficiency (ACE) and energy consumption (E_sp) model well matched the MO experimental degradation data. Our work broadens the scope of the application of ACPER in the treatment industry wastewater containing organics and provides a new strategy for the energy utilization evaluation during the removal of organic matter by electrocatalytic oxidation.

A novel composite anode via immobilizing of Ce-doped PbO2 on CoTiO3 for efficiently electrocatalytic degradation of dye

The exploitation of efficient electrocatalyst is significantly important for degradation of refractory organic pollutants. Herein, a novel Ti/CoTiO₃/Ce-PbO₂ composite electrocatalyst (abbreviated as CTO/CP) is successfully constructed via facile consecutive immersion pyrolysis and electro-deposition method and then systematically characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Fourier Transform infrared spectroscopy (FT-IR), energy dispersive spectroscopy (EDS) and near infrared chemical imaging (NIR-CI). Importantly, the electrochemical measurements demonstrate that the CTO/CP possesses numerous prominent properties such as lower charge transfer resistance, larger electroactive area, higher oxygen evolution potential than those of the pristine Ti/CoTiO₃ (CTO) and Ti/Ce-PbO₂ (CP). Thereby, the CTO/CP exhibits an enhanced electrocatalytic degradation performance with the degradation efficiency as high as 90.0% and COD removal rate of 88.3% at 180 min for the optimal CTO/CP (denoted as 10 layers of CTO and 1 h electrodeposition of CP), in which the ·OH is the major reactive species. Additionally, the optimal CTO/CP also shows a higher ICE/ACE together with lower EEC and desirable stability, universal applicability for many different dyes and reusability. Overall, this work offers a promising approach for enhancing the electrocatalytic properties of CTO via introducing CP.

Electrochemical study of a novel high-efficiency PbO2 anode based on a cerium-graphene oxide co-doping strategy: Electrodeposition mechanism, parameter optimization, and degradation pathways

A novel and efficient Ti/SnO₂-Sb/PbO₂-GO-Ce electrode was successfully fabricated based on the co-deposition of Ce ions and graphene oxide (GO) into β-PbO₂ crystals and used as an anode for electrocatalytic oxidation of phenol. The electrodeposition mechanism, parameter optimization, mechanism analysis, and potential degradation pathways were discussed in depth. The co-doping of GO and Ce resulted in the high directional specificity of β(301), orderly and dense grain arrangement of PbO₂ crystals. At the same time, the oxygen evolution potential, •OH generation capacity and lifetime were also improved. The effects of experimental parameters on phenol removal efficiency were evaluated, including the applied current density, electrode gap, supporting electrolyte, initial NaCl concentration, initial pH, and initial phenol concentration. Under the optimal conditions, the removal efficiency of phenol can reach 375.6 g m^-2 h^-1 for 20 min electrolysis, which is about 1.2 times that of the pure PbO₂ electrode. The active oxygen species (•OH, ClO^- and HClO) were important attributes to the degradation of phenol. Additionally, a potential degradation pathway for phenol was proposed. After 10 successive recycles, there was no significant difference of the electro-generated •OH, cell voltage and phenol removal rate, which confirms the stability and admirable reusability of Ti/SnO₂-Sb/PbO₂-GO-Ce electrode.

Enhanced perfluorooctane acid mineralization by electrochemical oxidation using Ti3+ self-doping TiO2 nanotube arrays anode

Perfluorooctanoic acid (PFOA) is of increasing concern due to its worldwide application and extremely environmental persistence. Herein, we demonstrated the electrochemical degradation of PFOA with high efficiency using the Ti³⁺ self-doping TiO₂ nanotube arrays (Ti³⁺/TiO₂-NTA) anode. The fabricated Ti³⁺/TiO₂-NTA anode exhibited vertically aligned uniform nanotubes structure, and was demonstrated good performance on the electrochemical degradation of PFOA in water. The degradation rate, total organic carbon (TOC) removal rate and defluorination rate of PFOA reached 98.1 %, 93.3 % and 74.8 %, respectively, after electrolysis for 90 min at low current density of 2 mA cm^-2. The energy consumption (7.6 Wh L^-1) of this electrochemical oxidation system using Ti³⁺/TiO₂-NTA anode for PFOA degradation was about 1 order of magnitude lower than using traditional PbO₂ anodes. Cathodic polarization could effectively prolong the electrocatalytic activity of the anode by regenerating Ti³⁺ sites. PFOA molecular was underwent a rapidly mineralization to CO₂ and F^-, with only low concentration of short-chain perflfluorocarboxylic acids (PFCAs) intermediates identified. A possible electrochemical degradation mechanism of PFOA was proposed, in which the initial direct electron transfer (DET) on the anode to yield PFOA free radicals (C₇F₁₅COO•) and hydroxyl radicals (•OH) oxidation were greatly enhanced. This presented study provides a novel approach for the purification of the recalcitrant PFOA from wastewaters.

Decolorization of textile wastewater by electrooxidation process using different anode materials: Statistical optimization

The presence of reactive dyes in textile wastewater is a serious environmental concern due to their associated mutagenic and carcinogenic effects. The present study aims to analyze the effect of different anodic materials on the decolorization of a real textile wastewater effluent. For this purpose, four different anodic materials-TiO2-coated platine, TiO2-coated ruthenium dioxide (RuO2) (viz., RuO2), titanium dioxide (TiO2), and graphite-were connected, respectively, to titanium dioxide (TiO2) used as a cathode electrode. Color and cost optimization studies were performed using the response surface methodology and the Box-Behnken experimental design (BBD). According to ANOVA results, the R2 values for Pt/TiO2, RuO2/TiO2, TiO2/TiO2, and graphite/TiO2 electrode pairs were found to be 97.4%, 93.8%, 92.44%, and 92.2%, respectively, indicating a good compatibility as it is close to one. The results show that color removal efficiencies at the optimal conditions were 86.3%, 90.8%, 91.5%, and 93.6% for Pt/TiO2, graphite/TiO2, TiO2/TiO2, and RuO2/TiO2, respectively. Furthermore, energy consumption cost at the optimum conditions was also evaluated, and the results were as follows: Pt/TiO2 (0.95 €/m3), graphite/TiO2 (0.74 €/m3), TiO2/TiO2 (0.31 €/m3), and RuO2/TiO2 (0.26 €/m3). Consequently, this research paper shows that all of the tested anodic materials give satisfactory color removal efficiencies higher than 86%. When energy consumption and color removal are considered together, the use of TiO2/TiO2 and RuO2/TiO2 pairs would be preferred. PRACTITIONER POINTS: Anodic contribution was investigated for decolorization of textile wastewater by electrooxidation process. Graphite, TiO2-coated Pt, TiO2-coated RuO2, and TiO2 were used as anode materials. Highest color removal with lowest energy consumption was achieved with TiO2-coated RuO2 anode material (93.6%).

Separable Magnetic Fe3O4@MoS2 Composite for Adsorption and Piezo-Catalytic Degradation of Dye

Well-designed composite catalysts are of increasing concern due to their improved performance compared to individual components. Herein, we designed and synthesized an Fe3O4@MoS2 composite via a simple hydrothermal method. As for the resultant composite, the MoS2 nanolayers presented a novel piezo-catalytic effect, while the Fe3O4 core provided a magnetic separation property. The structure and properties of Fe3O4@MoS2 were determined by relevant experiments. It was found that Fe3O4@MoS2 exhibited enhanced piezo-catalytic degradation of rhodamine B and good magnetic recovery/recycling features. The kobs for rhodamine B degradation over Fe3O4@MoS2 was 0.019 min−1—a little longer than that over MoS2 (0.013 min−1). Moreover, Fe3O4@MoS2 also showed a favorable ability to adsorb rhodamine B in solution, with a saturation adsorption of 26.8 mg/g. Further studies revealed that piezo-electrons, holes, and superoxide anions were key species in the piezo-catalytic degradation of rhodamine B. Notably, the step where oxygen trapped electrons to produce superoxide anions had a significant impact on the degradation of the dye. This work, not limited to the development of a high-performance MoS2-based piezo-catalyst, is expected to provide new insights into the working mechanisms and process profiles of composite piezo-catalysts.

Development of a novel graphitic carbon nitride and multiwall carbon nanotube co-doped Ti/PbO2 anode for electrocatalytic degradation of acetaminophen

In this work, we have constructed a novel graphitic carbon nitride/multiwall carbon nanotube (GCN/CNT) doped Ti/PbO₂ as anode for highly effective degradation of acetaminophen (ACE) wastewater. The ACE removal efficiency of 83.2% and chemical oxygen demand removal efficiency of 76.3% are achieved under the optimal condition of temperature 25 °C, initial pH 7, current density 15 mA cm^-2 and Na₂SO₄ concentration 6.0 g L^-1. The excellent electrocatalytic activity of Ti/PbO₂-GCN-CNT anode for ACE oxidation is ascribed to the effective suppression of oxygen evolution and the enhanced electron transfer after introducing GCN and CNT. Furthermore, Ti/PbO₂-GCN-CNT electrode displays excellent stability and reusability. ACE degradation is accomplished by direct oxidation and indirect oxidation, and ∙OH radical plays primary role in the indirect oxidation of ACE wastewater. The intermediates of ACE degradation are detailly investigated using LC-MS analysis and a possible degradation mechanism is proposed.

Fabrication of MOF-derivated CuOx-C electrode for electrochemical degradation of ceftazidime from aqueous solution

Antibiotic contamination has already been one of hazards to aquatic environment due to the abuse of antibiotics. Metal-organic frameworks (MOFs) are known as a kind of promising porous material for solving the environmental deterioration. In this article, the physicochemical and electrochemical properties of a series of porous copper oxide carbon materials (CuOx-C) synthesized by carbonizing Cu-BTC were compared. Due to the suitable carbonization temperature, CuOx-C-550 N, whose geometric structure was similar to Cu-BTC, possessed a multiscale pore structure containing many mesopores and partial macropores in accordance with the pore size distribution curves. More copper/copper oxides were introduced toimproving the electrochemical ability, evidence by XRD, XPS, CV and EIS characterization. Moreover, the degradation of ceftazidime (CAZ) through anodic oxidation was discussed. In AO/CuOx-C-550 N system, the effects of current, solution pH, initial CAZ concentration and Na₂SO₄ concentration were analyzed. CAZ removal rate reached 100% within 20 min under the optimal condition and a good electrocatalytic ability with 90% CAZ removal after 20 runs indicated a good electrochemical stability of CuOx-C-550 N. Furthermore, the degradation mechanism and pathway of CAZ were proposed. The Cu(II)/Cu(I) oxidation-reduction couples on the anodic surface contribute to the efficiently selective degradation of cephalosporins for CuOx-C-550 N. Overall, this study shows a good method to design and prepare a new MOF derivative for the remediation of aquatic contamination.

PbO2 modified with TiO2-NTs composite materials with enhanced OER electrocatalytic activity for Zn electrowinning

The high oxygen evolution overpotential of the Pb-Ag anode is one of the main reasons for the high energy consumption in Zn electrowinning. PbO2, owing to its high conductivity, good corrosion resistance and low cost, is widely used as an excellent coating material. In present research, a novel composite Ti/TiO2-NTs/PbO2 material was synthesized through a facile anodization, annealing, electrochemical reduction and galvanostatic deposition. The surface morphology, internal structure and the mechanisms of TiO2-NTs enhancing electrochemical performance were discussed. The results show that the self-organized high aspect ratio TiO2-NTs with diameter of ∼120 nm and length of ∼8 μm were obtained on Ti substrate. The Ti/TiO2-NTs/PbO2 composite material exhibits excellent oxygen evolution performance and good stability in Zn electrowinning simulation solution (50 g L-1 Zn2+, 150 g L-1 H2SO4) at 35 °C. Its oxygen evolution overpotential is only 630 mV under current density 50 mA cm-2, which is 332 m lower than that of Pb-0.76 wt% Ag (η = 962 mV) and only increases 22 mV after 5000 cycles of CV scanning. Its outstanding electrochemical performance is mainly ascribed to the introduction of TiO2-NTs in Pb(CH3COO)2 media since it refines the crystal grains, increases the electrochemical surface area, greatly reduces the charge transfer resistance (25.4 Ω cm2 to 2.337 Ω cm2) and enhances corrosion resistance. Therefore, the Ti/TiO2-NTs/PbO2 material prepared in Pb(CH3COO)2 medium may be an ideal anode for Zn electrowinning.

Removal of aniline from wastewater by electro-polymerization with superior energy efficiency

Removal of toxic aniline from wastewater is of great importance in industrial manufacture. Traditional electrochemical methods encounter obstacles such as high energy consumption in mineralization and severe electrode passivation in electro-polymerization. In this paper, we report a practical electro-polymerization method by using Ti/Sb-SnO₂/PbO₂ anode to treat high concentration aniline wastewater. The cyclic voltammetric experiment was conducted and the problem of electrode passivation was solved by increasing the electrode potential. In the experiments of treating aniline wastewater, the produced solid polymer can separate from water rather than sticking to electrode surface. Elemental analysis shows that oxygen is incorporated in the polymer. Experiments were conducted under different conditions, including current density, pH and initial concentration of aniline and Na₂SO₄. The electro-polymerization route accounts for nearly 50% contribution in the removal of chemical oxygen demand (COD). Our electro-polymerization method gives an apparent current efficiency (ACE) of 232.15% and an energy consumption (E_p) of 0.008658 kWh g^-1_COD^-1 when half of COD is removed at a current density of 15 mA cm^-2, pH of 7.0, initial aniline concentration of 1.2 g L^-1 and Na₂SO₄ concentration of 4 g L.^-1.

Fabrication of Co/Pr co-doped Ti/PbO2 anode for efficiently electrocatalytic degradation of β-naphthoxyacetic acid

The existence of β-naphthoxyacetic acid (BNOA) pesticide in water system has aroused serious environmental problem because of its potential toxicity for humans and organisms. Therefore, exploiting an efficient method without secondary pollution is extremely urgent. Herein, a promising Ti/PbO₂-Co-Pr composite electrode has been successfully fabricated through simple one-step electrodeposition for efficiently electrocatalytic degradation of BNOA. Compared with Ti/PbO₂, Ti/PbO₂-Co and Ti/PbO₂-Pr electrodes, Ti/PbO₂-Co-Pr electrode with smaller pyramidal particles possesses higher oxygen evolution potential, excellent electrochemical stability and outstanding electrocatalytic activity. The optimal degradation condition is assessed by major parameters including temperature, initial pH, current density and Na₂SO₄ concentration. The degradation efficiency and chemical oxygen demand removal efficiency of BNOA reach up to 94.6% and 84.6%, respectively, under optimal condition (temperature 35 °C, initial pH 5, current density 12 mA cm^-2, Na₂SO₄ concentration 8.0 g L^-1 and electrolysis time 3 h). Furthermore, Ti/PbO₂-Co-Pr electrode presents economic energy consumption and superior repeatability. Finally, the possible degradation mechanism of BNOA is put forward according to the main intermediate products identified by liquid chromatography-mass spectrometer. The present research paves a new path to degrade BNOA pesticide wastewater with Ti/PbO₂-Co-Pr electrode.

Electrochemical oxidation of ceftazidime with graphite/CNT-Ce/PbO2-Ce anode: Parameter optimization, toxicity analysis and degradation pathway

In this work, the electrochemical degradation of antibiotic ceftazidime has been studied using a novel rare earth metal Ce and carbon nanotubes codoped PbO₂ electrode. A competitively high oxygen evolution potential (2.4 V) and enhanced catalytic surface area were obtained, evidence by LSV and CV electrochemical characterization. The G/CNT-Ce/PbO₂-Ce electrode possessed a more compact structure and a smaller grain size than the other PbO₂ and Ce-PbO₂ electrodes, exhibiting a prolonged service lifetime, evidence by accelerated lifespan test and recycling degradation experiment. As electrolysis time reached 120 min, the removal efficiency of ceftazidime and TOC arrived at 100.0% and 54.2% respectively in 0.05 M Na₂SO₄ solution containing 50 mg⋅L^-1 ceftazidime. The effect of applied current density, pH value, initial ceftazidime concentration and chloride contents on the degradation performance were systematically evaluated. The results demonstrated that electrochemical oxidation of ceftazidime over the G/CNT-Ce/PbO₂-Ce electrode was highly effective, and the mineralization rate was greatly improved, compared with pristine PbO₂ electrode. Considering the toxicity was increased after 30 min electrolysis, the intermediates were quantitatively investigated through HPLC-MS, GC-MS and IC technology. According to the identified products, a reaction mechanism has been proposed and pyridine and aminothiazole were detected with concentration from approximately 1 to 3 mg⋅L^-1, which were regarded as toxic byproducts during electrooxidation. Further electrocatalyzing by ring cleavage reaction and complete mineralization to CO₂, NO₃^- and NH₄⁺ was proposed, which demonstrated the G/CNT-Ce/PbO₂-Ce electrode exhibited high efficiency for ceftazidime removal in mild conditions.

Electrochemical treatments of coking wastewater and coal gasification wastewater with Ti/Ti4O7 and Ti/RuO2-IrO2 anodes

Electrochemical treatments of coking wastewater (CW) and coal gasification wastewater (CGW) were conducted with Ti/Ti₄O₇ and Ti/RuO₂-IrO₂ anodes. The performances of Ti/Ti₄O₇ and Ti/RuO₂-IrO₂ anodes were investigated by analyzing the effects of five key influencing factors including anodes material, current density, anode-cathode distance, initial pH value, and electrolyte type. The removal efficiencies of total organic carbon (TOC) were analyzed during the processes of CW and CGW electro-oxidation. The removal efficiencies of sixteen polynuclear aromatic hydrocarbons (PAHs) in CW and CGW by electro-oxidation were also explored to further assess the electrochemical activities of Ti/Ti₄O₇ and Ti/RuO₂-IrO₂ anodes. The Ti/Ti₄O₇ anode achieved 78.7% COD removal efficiency of CW, 85.8% COD removal efficiency of CGW, 50.3% TOC removal efficiency of CW, and 54.8% TOC removal efficiency of CGW, higher than the Ti/RuO₂-IrO₂ anode (76.7%, 78.1%, 44.8% and 46.8%). The COD removal efficiencies increased with the applied current density, decreased with the increase of the anode-cathode distance, and slightly decreased with the increase of the initial pH value. Meanwhile, the removal efficiencies of sixteen PAHs by the Ti/Ti₄O₇ anode were mostly higher than those by the Ti/RuO₂-IrO₂ anode. By comprehensively analyzing the performances of Ti/Ti₄O₇ and Ti/RuO₂-IrO₂ anodes on electrochemical treatments of CW and CGW, this study may supply insights into the application potentials of these anodes to the electrochemical treatments of real wastewater.

Enhancement of the Activity of Electrochemical Oxidation of BPS by Nd-Doped PbO2 Electrodes: Performance and Mechanism

The electrochemical oxidation processes have attracted tremendous attention on the destruction of toxic and non-biodegradable organics. A series of neodymium (Nd)-doped PbO2 electrodes (Ti/PbO2-Nd) were synthesized through a pulse electrodeposition method, and its activity of bisphenol S (BPS) removal was further examined. The morphologies and structures were characterized by the X-ray diffraction (XRD), scanning electron microscopy (SEM) and an energy dispersive spectrometer (EDS). The performance, energy consumption and mechanism of electrochemical oxidation of BPS by Ti/PbO2-Nd electrode were also discussed. Compared to the traditional Ti/PbO2 electrode, the Ti/PbO2-Nd enables finer crystal particles, facilitating the oxygen evolution overpotential (OEP) from 1.41V to 1.55V and the generation of hydroxyl radicals (•OH). Moreover, lower duty cycles during the preparation of the electrode also contribute to the tapering size of crystals. The results show that the Ti/PbO2-Nd electrode exhibits relatively high activity in the anodic oxidation of BPS. Over 95% of BPS could be removed with the current density of 15 mA cm−2. Moreover, the energy consumption of BPS degradation on Ti/PbO2-Nd electrode is 60.26 kWh m−3, much lower than that on Ti/PbO2 electrode (95.45 kWh m−3). To conclude, the Ti/PbO2-Nd electrode has been proven to be a promising material for BPS removal.

A Novel Porous Ni, Ce-Doped PbO2 Electrode for Efficient Treatment of Chloride Ion in Wastewater

The porous Ti/Sb-SnO2/Ni-Ce-PbO2 electrode was prepared by using a porous Ti plate as a substrate, an Sb-doped SnO2 as an intermediate, and a PbO2 doped with Ni and Ce as an active layer. The surface morphology and crystal structure of the electrode were characterized by scanning electron microscope(SEM), energy dispersive spectrometer(EDS), and X-Ray diffraction(XRD). The electrochemical performance of the electrodes was tested by linear sweep voltammetry (LSV), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and electrode life test. The results show that the novel porous Ni-Ce-PbO2 electrodes with larger active surface area have better electrochemical activity and longer electrode life than porous undoped PbO2 electrodes and flat Ni-Ce-PbO2 electrodes. In this work, the removal of Cl− in simulated wastewater on three electrodes was also studied. The results show that the removal effect of the porous Ni-Ce-PbO2 electrode is obviously better than the other two electrodes, and the removal rate is 87.4%, while the removal rates of the other two electrodes were 72.90% and 80.20%, respectively. In addition, the mechanism of electrochemical dechlorinating was also studied. With the progress of electrolysis, we find that the increase of OH- inhibits the degradation of Cl−, however, the porous Ni-Ce-PbO2 electrode can effectively improve the removal of Cl−.

Effect of chloride on the one step electrochemical treatment of an industrial textile wastewater with tin dioxide anodes. The case of trichromy procion HEXL

The resulting solutions from the cotton fabrics dyeing using the trichromy Procion HEXL, with NaCl as electrolyte, were electrochemically treated. These dyes have two azo groups as chromophores and two monochlorotriazinic groups as reactive groups in their structure. The combined oxidation/reduction at 125 mA cm^-2 in a filter-press cell without compartment separation was carried out using an anode of Ti/SnO₂-Sb-Pt and a cathode of stainless steel. This procedure has been effective in previous experiments using sulphate as electrolyte. A significant decrease in total organic carbon (TOC), chemical oxygen demand (COD), and total nitrogen (TN) was obtained. Moreover, the process took place efficiently. The average oxidation state (AOS) and the carbon oxidation state (COS) data confirmed the presence of stable oxidized intermediates in the electrolysed solution. The chromatography and the UV-Visible spectrophotometry assays indicated that full decolourisation is obtained at a loaded charge of around 0.81 Ah L^-1 which is associated with an electrical energy per order (EEO) of 1.20 kWh m^-3.

Dimensional Stable Lead Electrode Modified by SDS for Efficient Degradation of Bisphenol A

The dimensional stable lead electrodes modified by sodium dodecyl sulfate (SDS) were prepared with electrochemical deposition and it shows that a more compact, uniform, and smooth film of Ti/PbO₂(F+SDS) electrode reduces the corroded crystal faces and surface defects. Characterization results demonstrate that the oxygen evolution potential (OEP) of the Ti/PbO₂(F+SDS) electrode was higher, and its service life is almost 1.6 times longer than the Ti/PbO₂(F) electrode. Compared with Ti/PbO₂(F) electrode, the soluble Pb concentration of the Ti/PbO₂(F+SDS) electrode decreased 15.1%, which indicates that the decrease of crystal surface defects leads to the reduction of Pb ions so that the excellent corrosion resistance electrodes cause low environmental risks. The modified electrodes were used as anodes to degrading bisphenol A (BPA) when an electrolyte is 0.2 M Na₂SO₄, the applied voltage is 5 V and electrodes distance is 3 cm, 20 mg/L BPA for electrolysis time of 180 min can reach up to 97.6%.

Cavitation erosion mechanisms in Co-based coatings exposed to seawater

The cavitation erosion (CE) of most materials in seawater is more serious than in fresh water due to the onset of corrosion; however, in a previous study we reported results that contradict this widely accepted trend. In this research our objective is to provide fundamental insight into the mechanisms that may be responsible for these earlier results. To accomplish this objective, two types of Co-based coatings, prepared by high velocity oxygen fuel (HVOF) spraying system, were used to further investigate the underlying corrosion-mitigating CE mechanism in seawater. Accordingly, the influence of spraying parameters on microstructure, composition and mechanical properties of the coatings was analyzed on the basis of SEM, XRD, Raman spectroscopy, Vicker's hardness and nano-indentation results. Electrochemical corrosion tests were used to evaluate the corrosion behavior of the Co-based coatings. Their CE performances in seawater and deionized water were comparatively studied by a vibratory apparatus. Results demonstrated that a higher flame temperature facilitated the oxides formation with associated improvements in compactness, hardness and toughness of the coatings. The presence of alumina in combination with the oxides formed in-situ facilitated the formation of an oxidation film on surfaces, and effectively enhanced the charge transfer resistance of the coating, thereby significantly improving the corrosion resistance in seawater. Metallic Co was not only more easily oxidized but also more readily corroded than the alloyed Co. Compactness was identified as an important factor affecting CE resistance of coatings in deionized water, because defects facilitate the nucleation and eventual collapse of bubbles. Moreover, bubble collapse produced a transient high temperature spike in excess of 600 °C that also caused Co and Cr elements to oxidize. Because the CE tests were carried out in seawater, additional Co₃O₄ and Cr₂O₃ were generated owing to corrosion that more effectively increased the surface compactness and mechanical properties of the coatings. This behavior was particular notable for coatings with metallic Co and Cr, which should be why seawater corrosion could weaken the CE of Co-based coatings.

Electrochemical degradation of safranine T in aqueous solution by Ti/PbO2 electrodes

The electrochemical degradation of safranine T (ST) in aqueous solution was studied. The effects of current density, initial concentration of ST, initial pH values, and Na2SO4 concentration on electrocatalytic degradation of ST in the aqueous solution by Ti/PbO2 electrode were analyzed. The experimental results showed that the electrochemical oxidization reaction of ST fitted a pseudo first order kinetics model. By using the Ti/ PbO2 electrode as the anode, 99.96% of ST can be eliminated at 120 min. It means that the electrochemical degradation of ST in aqueous solution by the Ti/PbO2 electrode was very effective. The optimal reaction conditions were as follows: current density, 40 mA cm−2; initial ST concentration, 100 mg L−1; Na2SO4 concentration, 0.20 mol L−1; initial pH, 6. It can be known from the test of UV–vis and HPLC in the reaction process that the intermediates will be generated, and the possible intermediate structure was studied by HPLC–MS test. However, with the progress of degradation reaction, the intermediates will eventually be oxidized into CO2 and H2O. Cyclic voltammetry and fluorescence experiments proved that ST was indirectly oxidized through the generation of hydroxyl radicals. Under the optimal reaction conditions, the energy required to completely remove ST was 17.92 kWh/m3.

Electrochemical removal of amoxicillin using a Cu doped PbO2 electrode: Electrode characterization, operational parameters optimization and degradation mechanism

This work investigated the electrochemical degradation of amoxicillin (AMX) in aqueous solution with Cu-PbO2 electrode. The main influence factors on the degradation of AMX, such as Na2SO4 concentration, initial AMX concentration, current density and initial pH value, were analyzed in detail. Under the optimal conditions, the removal rates of AMX and chemical oxygen demand (COD) reached 99.4% and 46.3% after 150 min treatment. The results indicated that the electrochemical degradation of AMX fitted pseudo-first-order reaction kinetics. Compared with undoped PbO2 electrode, Cu-PbO2 electrode had a smaller crystal size, more proportion of hydroxyl oxygen species, greater AMX and chemical oxygen demand (COD) removal efficiency, higher average current efficiency (ACE) and lower electrical efficiency per log order (EE/O). Electrochemical oxidation using Cu-PbO2 electrodes was an effective way to eliminate amoxicillin in aqueous solution. Moreover, a possible degradation pathway including ring open and mineralization was proposed by intermediate products determined by GC-MS method. This paper could provide basic data and technique reference for the amoxicillin wastewater pollution control.

Highly efficient modified lead oxide electrode using a spin coating/electrodeposition mode on titanium for electrochemical treatment of pharmaceutical pollutant

In this study, Ti/TiO₂/PbO₂ anodes consisting of a PbO₂ coating growth on the TiO₂ interlayer deposited on titanium substrates were prepared combining different deposition technics: electrochemical method using anodization (Anod), electrodeposition (EL), and sol gel spin coating (SG). Different kinds of anodes have been tested for the removal of ampicillin, a pharmaceutical pollutant, from water. The structure and the surface morphology of the prepared multiple coatings were characterized by scanning electron microscopy and Energy-Dispersive X-ray spectroscopy respectively. Electrochemical impedance spectroscopy was also investigated in order to study the electrocatalytic activity of the anodes. The performance of the electrodes was evaluated through high performance liquid chromatography and chemical oxygen demand (COD) measurements. It was noticed that ampicillin could be mineralized by anodic oxidation process using Ti/TiO₂/PbO₂ anodes. The best results were obtained for Ti/TiO₂^SG/PbO₂^EL as anode with a 64% of COD removal after 300 min of treatment and a fast decrease in the amount of ampicillin was reached after almost one hour. Experimental results demonstrate that Ti/TiO₂^SG/PbO₂^EL anode presents the best ability for the degradation of ampicillin through anodic oxidation compared to the Ti/TiO₂^SG/PbO₂^SG and Ti/TiO₂^Anod/PbO₂^EL electrodes.

Ti/PbO2-Sm2O3 composite based electrode for highly efficient electrocatalytic degradation of alizarin yellow R

In this work, a novel Ti/PbO₂-Sm₂O₃ composite electrode with high electrocatalytic activity is successfully fabricated via simple electrodeposition method and further investigated for electrochemical degradation of alizarin yellow R (AYR) wastewater. The test results of X-ray diffraction, field-emission scanning electron microscopy and energy-dispersive X-ray spectroscopy confirm that Sm₂O₃ is successfully composited with PbO₂. The coating of Ti/PbO₂-Sm₂O₃ composite electrode stacked by typical pyramid-like micro-particles exhibits smooth and compact surface morphology which is conducive to enhancing the corrosion resistance of electrode. Furthermore, electrochemical performance tests indicate that Ti/PbO₂-Sm₂O₃ composite electrode has advantages of higher oxygen evolution potential, lower charge transfer resistance and longer lifetime over Ti/PbO₂ electrode. Electrolyte concentration, plate space, initial pH and cell voltage are assessed to optimize the degradation condition of AYR. The results show that COD removal efficiency and degradation efficiency of AYR on Ti/PbO₂-Sm₂O₃ composite electrode reach up to 79.90% and 80.00% under the optimal conditions (Na₂SO₄ electrolyte concentration 9.0 g L^-1, plate space 3.0 cm, initial pH 5, cell voltage 3.0 V and electrolysis time 150 min), respectively. The degradation of AYR follows pseudo-first-order reaction kinetics, and a plausible mineralization pathway of AYR is proposed on the basis of the identification of major intermediate products. These results suggest that Ti/PbO₂-Sm₂O₃ composite electrode is a promising candidate for electrocatalytic degradation of AYR wastewater.

A novel electrocatalytic approach for effective degradation of Rh-B in water using carbon nanotubes and agarose

Carbon nanotubes (CNTs)/agarose (AG) membrane on the ITO (indium tin oxide) conductive glass, with high efficiency of electrocatalytic degradation for rhodamine B (Rh-B) in water, was prepared using an easy and green method. The prepared CNTs/AG membrane was characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive spectra (EDS), infrared spectroscopy (IR), and electrochemical impedance spectroscopy (EIS). The results revealed that CNTs were dispersed in the AG membrane. Additionally, the electrocatalytic activities for Rh-B were conducted on the electrochemical workstation with a three-electrode system. Both initial pH and potential played an important role in the process of electrocatalytic degradation. At pH 3 and potential reaching 4 V, the removal rate of Rh-B (10 mg/L) in water achieved 96% within 20 min. The stability of the prepared CNTs/AG membrane was also investigated. Besides, the toxicities of the main intermediates from the electrocatalytic degradation for Rh-B were calculated using the ECOSAR program and EPIWIN software, and results indicated that the toxicities of some intermediates were higher than those of the parent pollutant (Rh-B). These findings provided a light-spot to simplify the preparation of efficient working electrode and emphasized the possible potential risks from intermediates at the same time.