Microalgae-based bioremediation of water contaminated by pesticides in peri-urban agricultural areas

Smart nanocomposite of carbon quantum dots in double hydrogel (carboxymethyl cellulose/chitosan) for effectively adsorb and remove diquat herbicide: Characterization, thermodynamics, isotherms, kinetics, and optimizing through Box-Behnken Design

This research synthesized carbon quantum dots (CQDs) encapsulated in a chitosan (CS) and carboxymethyl cellulose (CMC) matrix. The crosslinking with epichlorohydrin formed (CQDs-CS/CMC) hydrogel beads for effective removal of diquat (DQ) herbicides. Various techniques like XRD, FT-IR, FESEM, EDX, XPS, and nitrogen adsorption/desorption isotherm analysis were used to evaluate the textural properties. The textural properties of the CQDs-CS/CMC were investigated through nitrogen adsorption/desorption isotherms. The surface area was found to be 95.72 m2/g, pore size 6.57 nm, and pore volume 0.313 cc/g. Post-DQ adsorption, these values decreased to 68.44 m2/g, 4.2 nm, and 0.162 cc/g, indicating DQ blocked mesopores and adsorption sites. The study also examined the effects of dosage, pH, temperature, and initial DQ concentration on adsorption, employing equilibrium and kinetic studies. The system conformed to pseudo-second-order kinetics and Langmuir isotherm models. Chemisorption was the main adsorption process, with an energy of 32.3 kJ/mol. Increased metal uptake at higher temperatures shows the process is spontaneous and endothermic. The Box-Behnken Design software identified optimal adsorption parameters: a pH of 8 and a dosage of 0.02 g of CQDs-CS/CMC per 25 mL of DQ solution, achieving 449.6 mg/g adsorption capability. Extensive testing using Design-Expert software substantially improved the adsorption procedure. The assessment of adsorbent stability involved six cycles of adsorption/desorption. Results showed consistent reusability with no significant reduction in removal efficacy. It maintained its initial chemical configuration before and after repurposing, exhibited consistent performance, and reliable XRD results.

Defect-enriched CuO/CeO2 nanostructure: in-depth structural characterization and photocatalytic performance

The catalytic activity of CeO2 can be modulated by incorporating defects and inducing strong metal-support interactions. Herein, we introduce CuO into CeO2 for generating oxygen vacancies (CeO2-x ) via the interaction between CuO and CeO2. The resultant catalyst CuO/CeO2 exhibited improved performance for the photocatalytic degradation of isoproturon (a herbicide). The improvement in catalytic performance was attributed to the oxygen vacancies and interfacial charge transfer between CuO and CeO2. Notably, the addition of CuO increased the oxygen vacancies in CeO2, correlating with the increase in the Ce3+ content (31.2%). X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy studies substantiated the increase in surface oxygen vacancies in CeO2. We investigated the oxygen vacancies quantitatively and detected the chemical states of the Cu and Ce species. Photoluminescence (PL) studies validated the role of oxygen vacancies in restraining the recombination of photogenerated electron and hole pairs, thereby improving the catalytic activity of CuO/CeO2. Trapping experiments were conducted to identify the reactive species involved in the photocatalytic degradation process. Based on a thorough evaluation of the characteristics of the catalyst and photocatalysis experimental outcomes, a potential reaction mechanism was proposed. Furthermore, high-resolution mass spectrometry (HRMS) analysis was utilized to identify degradation intermediates, enabling us to outline the possible degradation pathways of isoproturon. Isoproturon (IPU) was effectively degraded under UV light with CuO/CeO2 compared with pristine CeO2. A 95% degradation efficiency was achieved with CuO/CeO2 (10 mg) for the IPU solution (10 μg L-1) within 120 minutes. This study provides detailed insights into the structural analysis of defective CeO2 and an in-depth mechanism of its photocatalysis, facilitating the design of high-performance ceria-based catalysts for photocatalytic degradation of emerging contaminants in water.

Adsorption and eliminating of diquat herbicide using layer double hydroxide enclosed in double layer hydrogel beads of carboxymethyl cellulose and alginate: Synthesis, characterization, adsorption isotherm, kinetics, thermodynamics and optimization via box-behnken design

This study involved the creation of AlCu-layered double hydroxide (LDH) encapsulated in carboxymethyl cellulose (CMC) and alginate (Alg), which was then crosslinked with epichlorohydrin to form hydrogel beads (AlCu-LDH/CMC-Alg hydrogel beads) used for the removal of diquat (DQ) herbicide. The resulting material, AlCu-LDH/CMC-Alg hydrogel beads, underwent a comprehensive analysis of its properties using XRD, FT-IR, XPS, EDX, N2 adsorption/desorption isotherm, and FESEM to determine its textural characteristics. The AlCu-LDH/CMC-Alg hydrogel beads was analyzed using nitrogen adsorption/desorption isotherms to assess its textural properties. The hydrogel beads of AlCu-LDH/CMC-Alg showed a surface area of 114.22 m2/g, a pore volume of 0.35 cc/g, and a pore radius of 3.62 nm, indicating a mesoporous structure with a notable adsorption capacity. Following the adsorption of DQ, these measurements decreased to 65.145 m2/g, 0.2 cc/g, and 2.4 nm, respectively, suggesting that the DQ had filled or blocked the pores. This study also analyzed the impact of dose, pH, temperature, and initial concentration on the adsorption process. Equilibrium and adsorption kinetics were used to examine the adsorption characteristics. The process followed the pseudo-second-order and Langmuir isotherm models. The primary adsorption mechanism identified was chemisorption, with an adsorption energy of 29.6 kJ.mol-1. The rise in DQ absorption at higher temperatures suggests an endothermic and spontaneous adsorption process. The optimal adsorption parameters, as determined by the Box-Behnken design software, are a pH of 8, a dosage of 0.02 g of AlCu-LDH/CMC-Alg hydrogel beads per 25 mL, and an adsorption capacity of 302.6 mg/g for the DQ solution. Through careful testing and utilization of the Box-Behnken design and response surface technique in the Design-Expert software, significant enhancements were made to the adsorption process. The stability of the adsorbent was assessed by conducting six successive cycles of adsorption and desorption, revealing that its reusability remained steady with no noticeable decline in removal efficiency. Furthermore, it preserved its original chemical makeup both before and after being reused, demonstrated steady effectiveness, and kept consistent X-ray diffraction (XRD) results.

The adsorption of chlorpyrifos and malathion under environmentally relevant conditions using biowaste carbon materials

Water bodies face persistent contamination from organophosphorus pesticides like chlorpyrifos and malathion, which pose substantial environmental and health hazards due to their toxicity and resilience in ecosystems. This study explores the potential of spent coffee grounds, a common agricultural byproduct, as an eco-friendly adsorbent for eliminating these pesticides from polluted water. Spent coffee grounds underwent carbonization at 400 °C and various activation treatments using KOH, H3PO4, CO2, and their combinations. The impact of these activation methods on the adsorption capacity of carbonized materials was assessed under environmentally relevant conditions (25 °C, pH=6, and typical pesticide concentrations in wastewater). Results revealed that the physical and chemical properties of biowaste-derived materials significantly influence their adsorption efficiency, with KOH-activated adsorbents exhibiting the highest capacities ((16.1 ± 0.8) mg g-1 for chlorpyrifos and (11.2 ± 0.2) mg g-1 for malathion). Spent coffee grounds carbonized at 400 °C without additional activation demonstrated similar adsorption performance to the best-performing material ((19.4 ± 0.4) mg g-1 for chlorpyrifos and (10.6 ± 0.4) mg g-1 for malathion), with notably lower economic and environmental costs. Given its straightforward preparation and significant adsorption capacity, this material stands out as a sustainable solution for treating agrochemical wastewater containing chlorpyrifos and malathion.

Pesticide pollution: toxicity, sources and advanced remediation approaches

The Food and Agricultural Organization of the United Nations (FAO) estimates that food production must rise by 70% to meet the demands of an additional 2.3 billion people by 2050. This forecast underscores the persistent reliance on pesticides, making it essential to assess their toxicity and develop effective remediation strategies. Given the widespread utilisation of pesticides, it requires an urgent need to evaluate their toxicity and explore feasible remediation approaches for their removal. Hence, this review provides an overview of the latest information on the presence, distribution, sources, fate, and trends of pesticides in global environmental matrices, emphasizing the ecological and health risks posed by pesticide pollution. Currently, the dominant remediation techniques encompass physical, chemical, and biological methods, yet studies focusing on advanced remediation techniques remain limited. This review critically evaluates both newer and traditional approaches to pesticide removal, offering a descriptive and analytical comparison of various methods. The selection of the appropriate treatment method depends largely on the nature of the pesticide and the effectiveness of the chosen technique. In many cases, technologies such as membrane bioreactors and the fenton process could be integrated with biological technologies to enhance performance and overcome limitations. The study concludes that a hybrid approach combining various remediation strategies offers the most effective and sustainable solution for pesticide removal. Finally, the review underscores the need for further scientific investigation into the most viable technologies while discussing the challenges and prospects of developing safe, reliable, cost-effective, and eco-friendly methods for removing pesticides from the environment.

Unveiling the Contamination of Thiocyanate, Perchlorate, and Chlorate in Edible Microalgae: Detection, Distribution, and Risk Assessment in Sustainable Food Sources

With the growing interest in microalgae as a sustainable food source, concerns about potential chemical contaminants in these products have emerged. In this study, a sensitive and reliable LC-MS/MS method was developed for the simultaneous detection of thiocyanate, perchlorate, and chlorate in edible microalgae samples. The method was validated with excellent linearity (R2 > 0.998), low detection limits (LOD: 1-8 μg/kg), quantification limits (LOQ: 4-26 μg/kg), and high recovery rates (75-101.9%) across different sample types. We collected a total of 77 microalgae products based on the available varieties in the market, including 43 Spirulina powder samples, 10 Chlorella powder samples, and 24 microalgae-based food products, sourced from key microalgae production regions in China. The contamination levels for thiocyanate (median: 1843.06-2645.72 μg/kg) and perchlorate (median: 23.29-31.4 μg/kg) were consistently quantitated in all samples, while chlorate concentrations showed greater variability (median: 18.94-160.21 μg/kg). Risk assessment revealed a significant dietary exposure risk to thiocyanate, with estimated daily intake (EDI) values exceeding the EPA's subchronic reference dose, whereas no significant risk was identified for perchlorate or chlorate. Monte Carlo simulations further supported the conclusion that perchlorate and chlorate posed minimal dietary risks, while thiocyanate exposure warrants concern. This study not only provides a foundational method for monitoring these contaminants in microalgae but also contributes critical data for future food safety standards and regulatory practices regarding edible microalgae products.

Exploring Extremotolerant and Extremophilic Microalgae: New Frontiers in Sustainable Biotechnological Applications

Exploring extremotolerant and extremophilic microalgae opens new frontiers in sustainable biotechnological applications. These microorganisms thrive in extreme environments and exhibit specialized metabolic pathways, making them valuable for various industries. The study focuses on the ecological adaptation and biotechnological potential of these microalgae, highlighting their ability to produce bioactive compounds under stress conditions. The literature reveals that extremophilic microalgae can significantly enhance biomass production, reduce contamination risks in large-scale systems, and produce valuable biomolecules such as carotenoids, lipids, and proteins. These insights suggest that extremophilic microalgae have promising applications in food, pharmaceutical, cosmetic, and biofuel industries, offering sustainable and efficient alternatives to traditional resources. The review concludes that further exploration and utilization of these unique microorganisms can lead to innovative and environmentally friendly solutions in biotechnology.

Benzo(b)fluoranthene and benzo(k)fluoranthene removal by microalgae in the presence of triazine herbicides: Matrix solid-phase dispersion and solid-phase extraction (MSPD/SPE) for HPLC-UV analysis of the different culture components

Over the last decade, human activities in the industrial and agricultural sectors have significantly increased the concentration of persistent and harmful pollutants in aquatic ecosystems. The use of microorganisms is a green strategy for the bio-removal of certain contaminants. However, other pollutants in the same ecosystems can reduce their degrading activity and even affect their survival. Therefore, this study aimed to evaluate the efficiency of benzo(b)fluoranthene (BbF) and benzo(k)fluoranthene (BkF) removal by Selenastrum capricornutum in the presence of triazine herbicides, compounds mainly used in broadleaf weeds. The interest of this work focused on identifying in which of the microalgal components the degrading activity is best evidenced and affected. For this purpose, the use of solid-phase extraction (SPE) and matrix solid-phase dispersion (MSPD) extraction procedures and HPLC-UV analysis allowed the BbF and BkF trace quantification in biomass, liquid medium, and cell lysate separately from cultures exposed to these polycyclic aromatic hydrocarbons (PAHs) alone or with herbicides. The recovery percentages were between 78 and 94 %, good linearity (r2 ≈ 0.99), precision values measured as RSD < 15 %, and limits of detection (LOQs) at levels of ng mL-1 and ng mg-1 were obtained. The individual PAH amounts measured in the components of microalgae cultures show similar removal kinetics (removal percentages: 82-89 %). Likewise, the analysis demonstrated that the removal of PAHs is not affected in the presence of triazine herbicides (atrazine and cyanazine) and with similar removal percentages (79-86 %) compared to those cultures exposed to individual PAHs (74-83 %). These results support the possible real-world applications of PAH removal by extracts from S. capricornutum in aquatic environments contaminated with PAHs and near agriculture areas where triazine herbicides are used.

Bioremediation potential of microalgae for sustainable soil treatment in India: A comprehensive review on heavy metal and pesticide contaminant removal

The escalating environmental concerns arising from soils contamination with heavy metals (HMs) and pesticides (PSTs) necessitate the development of sustainable and effective remediation strategies. These contaminants, known for their carcinogenic properties and toxicity even at small amounts, pose significant threats to both environmental ecology and human health. While various chemical and physical treatments are employed globally, their acceptance is often hindered by prolonged remediation times, high costs, and inefficacy in areas with exceptionally high pollutant concentrations. A promising emerging trend in addressing this issue is the utilization of microalgae for bioremediation. Bioremediation, particularly through microalgae, presents numerous benefits such as high efficiency, low cost, easy accessibility and an eco-friendly nature. This approach has gained widespread use in remediating HM and PST pollution, especially in large areas. This comprehensive review systematically explores the bioremediation potential of microalgae, shedding light on their application in mitigating soil pollutants. The paper summarizes the mechanisms by which microalgae remediate HMs and PSTs and considers various factors influencing the process, such as pH, temperature, pollutant concentration, co-existing pollutants, time of exposure, nutrient availability, and light intensity. Additionally, the review delves into the response and tolerance of various microalgae strains to these contaminants, along with their bioaccumulation capabilities. Challenges and future prospects in the microalgal bioremediation of pollutants are also discussed. Overall, the aim is to offer valuable insights to facilitate the future development of commercially viable and efficient microalgae-based solutions for pollutant bioremediation.

Effects of the Pesticide Carbofuran on Two Species of Chlorophyceae (Desmodesmus communis and Pseudopediastrum boryanum) and Their Pesticide Bioremediation Ability

Carbofuran is one of the most toxic broad-spectrum pesticides. We evaluated the effects of carbofuran on two species of microalgae, Pseudopediastrum boryanum and Desmodesmus communis, through measurements of cell viability, biomass, chlorophyll content, and the production of reactive oxygen species (ROS). The ability of these algae to remove carbofuran dissolved in the media was also determined. For the evaluations, both microalgae species were exposed to carbofuran (FURADAN 350 SC®) at concentrations of 100, 1000, and 10,000 µg L-1 for 7 days. Algae cell viability and chlorophyll-a concentration were not affected by the presence of carbofuran. Both species grew when exposed to the pesticide; however, the microalgae D. communis grew less than its respective control when exposed to the highest concentration (10,000 µg L-1 of carbofuran), indicating an adverse effect of the pesticide on this species. A significant increase in ROS production was observed in D. communis and P. boryanum when exposed to the highest concentration tested. The microalgae P. boryanum completely removed carbofuran in the media within 2 days, regardless of the concentration, whereas D. communis achieved the same result only after 5 days of exposure. Growth inhibition was observed only until the disappearance of carbofuran from the media. The present study suggests the use of microalgae, mainly P. boryanum, as potential tools for the remediation of environments contaminated by carbofuran because of their resistance to the insecticide and their ability to remove it rapidly from water. Environ Toxicol Chem 2024;00:1-12. © 2023 SETAC.

Fate of pesticides in agricultural runoff treatment systems: Occurrence, impacts and technological progress

The levels of pesticides in air, water, and soil are gradually increasing due to its inappropriate management. In particular, agricultural runoff inflicts the damages on the ecosystem and human health at massive scale. Present study summarizes 70 studies in which investigations on removal or treatment of pesticides/insecticides/herbicides are reported. A bibliometric analysis was also done to understand the recent research trends through the analysis of 2218 publications. The specific objectives of this study are as follows: i) to inventorize the characteristics details of agriculture runoff and analyzing the occurrence and impacts of pesticides, ii) analyzing the role and interaction of pesticides in different environmental segments, iii) investigating the fate of pesticides in agriculture runoff treatment systems, iv) summarizing the experiences and findings of most commonly technology deployed for pesticides remediation in agriculture runoff including target pesticide(s), specifications, configuration of technological intervention. Among the reported technologies for pesticide treatment in agriculture runoff, constructed wetland was at the top followed by algal or photobioreactor. Among various advanced oxidation processes, photo Fenton method is mainly used for pesticides remediation such as triazine, methyl parathion, fenuron and diuron. Algal bioreactors are extensively used for a wide range of pesticides treatment including 2,4-Dichlorophenoxyacetic acid, 2-methyl-4-chlorophenoxyacetic acid, alachlor, diuron, chlorpyrifos, endosulfan, and imidacloprid; especially at lower hydraulic retention time of 2-6 h. This study highlights that hybrid approaches can offers potential opportunities for effective removal of pesticides in a more viable manner.

Microbiology and Biochemistry of Pesticides Biodegradation

Pesticides are chemicals used in agriculture, forestry, and, to some extent, public health. As effective as they can be, due to the limited biodegradability and toxicity of some of them, they can also have negative environmental and health impacts. Pesticide biodegradation is important because it can help mitigate the negative effects of pesticides. Many types of microorganisms, including bacteria, fungi, and algae, can degrade pesticides; microorganisms are able to bioremediate pesticides using diverse metabolic pathways where enzymatic degradation plays a crucial role in achieving chemical transformation of the pesticides. The growing concern about the environmental and health impacts of pesticides is pushing the industry of these products to develop more sustainable alternatives, such as high biodegradable chemicals. The degradative properties of microorganisms could be fully exploited using the advances in genetic engineering and biotechnology, paving the way for more effective bioremediation strategies, new technologies, and novel applications. The purpose of the current review is to discuss the microorganisms that have demonstrated their capacity to degrade pesticides and those categorized by the World Health Organization as important for the impact they may have on human health. A comprehensive list of microorganisms is presented, and some metabolic pathways and enzymes for pesticide degradation and the genetics behind this process are discussed. Due to the high number of microorganisms known to be capable of degrading pesticides and the low number of metabolic pathways that are fully described for this purpose, more research must be conducted in this field, and more enzymes and genes are yet to be discovered with the possibility of finding more efficient metabolic pathways for pesticide biodegradation.

Removal of organic and inorganic contaminants from the air, soil, and water by algae

Rapid increases in human populations and development has led to a significant exploitation of natural resources around the world. On the other hand, humans have come to terms with the consequences of their past mistakes and started to address current and future resource utilization challenges. Today's primary challenge is figuring out and implementing eco-friendly, inexpensive, and innovative solutions for conservation issues such as environmental pollution, carbon neutrality, and manufacturing effluent/wastewater treatment, along with xenobiotic contamination of the natural ecosystem. One of the most promising approaches to reduce the environmental contamination load is the utilization of algae for bioremediation. Owing to their significant biosorption capacity to deactivate hazardous chemicals, macro-/microalgae are among the primary microorganisms that can be utilized for phytoremediation as a safe method for curtailing environmental pollution. In recent years, the use of algae to overcome environmental problems has advanced technologically, such as through synthetic biology and high-throughput phenomics, which is increasing the likelihood of attaining sustainability. As the research progresses, there is a promise for a greener future and the preservation of healthy ecosystems by using algae. They might act as a valuable tool in creating new products.

Solar-powered P450 catalysis: Engineering electron transfer pathways from photosynthesis to P450s

With the increasing focus on green chemistry, biocatalysis is becoming more widely used in the pharmaceutical and other chemical industries for sustainable production of high value and structurally complex chemicals. Cytochrome P450 monooxygenases (P450s) are attractive biocatalysts for industrial application due to their ability to transform a huge range of substrates in a stereo- and regiospecific manner. However, despite their appeal, the industrial application of P450s is limited by their dependence on costly reduced nicotinamide adenine dinucleotide phosphate (NADPH) and one or more auxiliary redox partner proteins. Coupling P450s to the photosynthetic machinery of a plant allows photosynthetically-generated electrons to be used to drive catalysis, overcoming this cofactor dependency. Thus, photosynthetic organisms could serve as photobioreactors with the capability to produce value-added chemicals using only light, water, CO2 and an appropriate chemical as substrate for the reaction/s of choice, yielding new opportunities for producing commodity and high-value chemicals in a carbon-negative and sustainable manner. This review will discuss recent progress in using photosynthesis for light-driven P450 biocatalysis and explore the potential for further development of such systems.

Remediation technologies for neonicotinoids in contaminated environments: Current state and future prospects

Neonicotinoids (NEOs) are synthetic insecticides with broad-spectrum insecticidal activity and outstanding efficacy. However, their extensive use and persistence in the environment have resulted in the accumulation and biomagnification of NEOs, posing significant risks to non-target organisms and humans. This review provides a summary of research history, advancements, and highlighted topics in NEOs remediation technologies and mechanisms. Various remediation approaches have been developed, including physiochemical, microbial, and phytoremediation, with microbial and physicochemical remediation being the most extensively studied. Recent advances in physiochemical remediation have led to the development of innovative adsorbents, photocatalysts, and optimized treatment processes. High-efficiency degrading strains with well-characterized metabolic pathways have been successfully isolated and cultured for microbial remediation, while many plant species have shown great potential for phytoremediation. However, significant challenges and gaps remain in this field. Future research should prioritize isolating, domesticating or engineering high efficiency, broad-spectrum microbial strains for NEO degradation, as well as developing synergistic remediation techniques to enhance removal efficiency on multiple NEOs with varying concentrations in different environmental media. Furthermore, a shift from pipe-end treatment to pollution prevention strategies is needed, including the development of green and economically efficient alternatives such as biological insecticides. Integrated remediation technologies and case-specific strategies that can be applied to practical remediation projects need to be developed, along with clarifying NEO degradation mechanisms to improve remediation efficiency. The successful implementation of these strategies will help reduce the negative impact of NEOs on the environment and human health.

Impact of wastewater characteristics on the removal of organic micropollutants by Chlorella sorokiniana

Microalgae-based technologies can be used for the removal of organic micropollutants (OMPs) from different types of wastewater. However, the effect of wastewater characteristics on the removal is still poorly understood. In this study, the removal of sixteen OMPs by Chlorella sorokiniana, cultivated in three types of wastewater (anaerobically digested black water (AnBW), municipal wastewater (MW), and secondary clarified effluent (SCE)), were assessed. During batch operational mode, eleven OMPs were removed from AnBW and MW. When switching from batch to continuous mode (0.8 d HRT), the removal of most OMPs from AnBW and MW decreased, suggesting that a longer retention time enhances the removal of some OMPs. Most OMPs were not removed from SCE since poor nutrient availability limited C. sorokiniana growth. Further correlation analyses between wastewater characteristics, biomass and OMPs removal indicated that the wastewater soluble COD and biomass concentration predominantly affected the removal of OMPs. Lastly, carbon uptake rate had a higher effect on the removal of OMPs than nitrogen and phosphate uptake rate. These data will give an insight on the implementation of microalgae-based technologies for the removal of OMPs in wastewater with varying strengths and nutrient availability.

Progress on microalgae cultivation in wastewater for bioremediation and circular bioeconomy

Water usage increased alongside its competitiveness due to its finite amount. Yet, many industries still rely on this finite resource thus recalling the need to recirculate their water for production. Circular bioeconomy is presently the new approach emphasizing on the 'end-of-life' concept with reusing, recycling, and recovering materials. Microalgae are the ideal source contributing to circular bioeconomy as it exhibits fast growth and adaptability supported by biological rigidity which in turn consumes nutrients, making it an ideal and capable bioremediating agent, therefore allowing water re-use as well as its biomass potential in biorefineries. Nevertheless, there are challenges that still need to be addressed with consideration of recent advances in cultivating microalgae in wastewater. This review aimed to investigate the potential of microalgae biomass cultivated in wastewater. More importantly, how it'll play a role in the circular bioeconomy. This includes an in-depth look at the production of goods coming from wastes tattered by emerging pollutants. These emerging pollutants include microplastics, antibiotics, ever-increasingly sewage water, and heavy metals which have not been comprehensively compared and explored. Therefore, this review is aiming to bring new insights to researchers and industrial stakeholders with interest in green alternatives to eventually contribute towards environmental sustainability.

Bioaccumulation of organochlorine pesticide residues (OCPs) at different growth stages of pacific white leg shrimp (Penaeus vannamei): First report on ecotoxicological and human health risk assessment

Pesticide residues (PRs) in farmed shrimps are concerning food safety risks. Globally, India is a major exporter of pacific white leg shrimp (P. vannamei). This study was undertaken to analyze PRs in the water, sediments, shrimps, and feed at different growth stages to evaluate the ecotoxicological and human health risks. PRs in the seawater and sediments ranged from not detected (ND) to 0.027 μg/L and 0.006-12.39 μg/kg, and the concentrations were within the maximum residual limits (MRLs) and sediment quality guidelines prescribed by the World Health Organization and Canadian Environment Guidelines, respectively. PRs in shrimps at three growth stages viz. Postlarvae, juvenile, and adults, ranged from ND to 0.522 μg/kg, below the MRLs set by Codex Alimentarius Commission and European Commission. Most of the PRs in water, sediments, and shrimps did not vary significantly (p > 0.05) from days of culture (DOC-01) to DOC-90. The hazard quotient (HQ) and hazard ratio (HR) were found to be < 1, indicating that consumption of shrimps has no noncarcinogenic and carcinogenic risks. PRs in shrimp feed ranged from ND to 0.777 μg/kg and were found to be below the MRLs set by EC, which confirms that the feed fed is safe for aquaculture practices and does not biomagnify in animals. The risk quotient (RQ) and toxic unit (TU) ranged from insignificant level (ISL) to 0.509 and ISL to 0.022, indicating that PRs do not pose acute and chronic ecotoxicity to aquatic organisms. The study suggested no health risk due to PRs in shrimps cultured in India and exported to the USA, China, and Japan. However, regular monitoring of PRs is recommended to maintain a sustainable ecosystem.

Microalgae-based removal of pollutants from wastewaters: Occurrence, toxicity and circular economy

The natural and anthropogenic sources of water bodies are contaminated with diverse categories of pollutants such as antibiotics, pharmaceuticals, pesticides, heavy metals, organic compounds, and other industrial chemicals. Depending on the type and the origin of the pollutants, the degree of contamination can be categorized into lower to higher concentrations. Therefore, the removal of hazardous chemicals from the environment is an important aspect. The physical, chemical and biological approaches have been developed and implemented to treat wastewaters. The microbial and algal treatment methods have emerged as a growing field due to their eco-friendly and sustainable approach. Particularly, microalgae emerged as a potential organism for the treatment of contaminated water bodies. The microalgae of the genera Chlorella, Anabaena, Ankistrodesmus, Aphanizomenon, Arthrospira, Botryococcus, Chlamydomonas, Chlorogloeopsis, Dunaliella, Haematococcus, Isochrysis, Nannochloropsis, Porphyridium, Synechococcus, Scenedesmus, and Spirulina reported for the wastewater treatment and biomass production. Microalgae have the potential for adsorption, bioaccumulation, and biodegradation. The microalgal strains can mitigate the hazardous chemicals via their diverse cellular mechanisms. Applications of the microalgae strains were found to be effective for sustainable developments and circular economy due to the production of biomass with the utilization of pollutants.

Two constructed wetlands within a Mediterranean natural park immersed in an agrolandscape reduce most heavy metal water concentrations and dampen the majority of pesticide presence

The water concentrations of 12 heavy and other metals/metalloids were analyzed seasonally along two horizontal-flow constructed wetlands (CWs) (Tancat Mília-TM and Tancat l'Illa-TLI) located within the Mediterranean Albufera de València Natural Park during 2020-2021. A wide-scope screening of pesticides present in waters was also performed. The two CWs were created to improve water quality and increase biodiversity. They currently receive effluent waters from two different tertiary-treatment wastewater plants, and the water flows along the CWs before being discharged into the main lagoon and a smaller lagoon in TM and TLI, respectively. TLI manages to reduce (Mn) or maintain the concentration of most of the studied elements (Zn, Ni, Hg, Cr, Fe Cd, Cu) at the same level as outside (67%). Only Al, Pb, B, and As remain at a higher concentration. TM also reduces Zn and Cu and keeps the concentration of Cr, Cd, and Hg (representing 42%). Al, Pb, B, and As remain at higher concentrations, as in TLI, but Ni, Fe, and Mn are also at higher concentrations. Although both CWs vary in their ability to remove elements, no risks to human health or the environment have been detected due to the low metal concentration in their outlets, all of them (except Hg) below the legal limits for environmental quality in the European Union. With the detection of 71 compounds in water in each CW area (26 herbicides, 26 insecticides, and 19 fungicides in TLI, and 29 herbicides, 23 insecticides, and 19 fungicides in TM), we also provide evidence of the impact of pesticides, which depends on the application method (helicopter, tractor), originated from areas with high agricultural pressure (chiefly rice crops) on systems (mainly TM) created to preserve biodiversity. Nevertheless, both systems provide crucial environmental services in water quality in this agrolandscape.

Daphnia as a Sentinel Species for Environmental Health Protection: A Perspective on Biomonitoring and Bioremediation of Chemical Pollution

Despite available technology and the knowledge that chemical pollution damages human and ecosystem health, chemical pollution remains rampant, ineffectively monitored, rarely prevented, and only occasionally mitigated. We present a framework that helps address current major challenges in the monitoring and assessment of chemical pollution by broadening the use of the sentinel species Daphnia as a diagnostic agent of water pollution. And where prevention has failed, we propose the application of Daphnia as a bioremediation agent to help reduce hazards from chemical mixtures in the environment. By applying "omics" technologies to Daphnia exposed to real-world ambient chemical mixtures, we show improvements at detecting bioactive components of chemical mixtures, determining the potential effects of untested chemicals within mixtures, and identifying targets of toxicity. We also show that using Daphnia strains that naturally adapted to chemical pollution as removal agents of ambient chemical mixtures can sustainably improve environmental health protection. Expanding the use of Daphnia beyond its current applications in regulatory toxicology has the potential to improve both the assessment and the remediation of environmental pollution.

Bioenergy, Biofuels, Lipids and Pigments—Research Trends in the Use of Microalgae Grown in Photobioreactors

This scientometric review and bibliometric analysis aimed to characterize trends in scientific research related to algae, photobioreactors and astaxanthin. Scientific articles published between 1995 and 2020 in the Web of Science and Scopus bibliographic databases were analyzed. The article presents the number of scientific articles in particular years and according to the publication type (e.g., articles, reviews and books). The most productive authors were selected in terms of the number of publications, the number of citations, the impact factor, affiliated research units and individual countries. Based on the number of keyword occurrences and a content analysis of 367 publications, seven leading areas of scientific interest (clusters) were identified: (1) techno-economic profitability of biofuels, bioenergy and pigment production in microalgae biorefineries, (2) the impact of the construction of photobioreactors and process parameters on the efficiency of microalgae cultivation, (3) strategies for increasing the amount of obtained lipids and obtaining biodiesel in Chlorella microalgae cultivation, (4) the production of astaxanthin on an industrial scale using Haematococcus microalgae, (5) the productivity of biomass and the use of alternative carbon sources in microalgae culture, (6) the effect of light and carbon dioxide conversion on biomass yield and (7) heterotrophy. Analysis revealed that topics closely related to bioenergy production and biofuels played a dominant role in scientific research. This publication indicates the directions and topics for future scientific research that should be carried out to successfully implement economically viable technology based on microalgae on an industrial scale.

A review on magnetic sensors for monitoring of hazardous pollutants in water resources

Water resources have long been of interest to humans and have become a serious issue in all aspects of human life. The disposal of hazardous pollutants in water resources is one of the biggest global concerns and poses many risks to human health and aquatic life. Therefore, the control of hazardous pollutants in water resources plays an important role, when it comes to evaluating water quality. Due to low toxicity, good electrical conductivity, facile functionalization, and easy preparation, magnetic materials have become a good alternative in recent years to control hazardous pollutants in water resources. In the present study, the idea of using magnetic sensors in controlling and monitoring of pharmaceuticals, pesticides, heavy metals, and organic pollutants have been reviewed. The water pollutants in drinking water, groundwater, surface water, and seawater have been discussed. The toxicology of water hazardous pollutants has also been reviewed. Then, the magnetic materials were discussed as sensors for controlling and monitoring pollutants. Finally, future remarks and perspectives on magnetic nanosensors for controlling hazardous pollutants in water resources and environmental applications were explained.

Occurrence of priority substances in urban wastewaters of Istanbul and the estimation of the associated risks in the effluents

Increase in the contamination of the aquatic environments is a global challenge; hence, understanding the sources of priority substances (PSs) is essential. In an attempt to implement this principle, a year-long monitoring covering all seasons was carried out in the influents and effluents of four largest wastewater treatment plants (WWTPs) in Istanbul. Results obtained showed the presence of 48 PSs (66% of the target compounds) including pesticides, polycyclic aromatic hydrocarbons (PAHs), volatile organic compounds (VOCs), dioxins and dioxin-like compounds (DLCs), alkylphenols, phthalates, and metals ranging from low nanograms to micrograms per liter. Priority hazardous substances that were banned for long were still found to be present in wastewaters. PAHs, DLCs, alkylphenols, and metals were found to be present in all samples. Di(2-ethylhexyl) phthalate (DEHP) and DLCs were detected in more than 80% of the influent samples. Trichloromethane had the highest concentrations among the most frequently (80-100%) detected PSs in the influents and effluents. The potential risks that may arise from WWTP effluents containing PSs were estimated by calculating the risk quotients (RQs). Upon the risk estimation conducted on the PSs in effluents, monitoring of the endrin, alpha-cypermethrin, theta-cypermethrin, zeta-cypermethrin, quinoxyfen, bifenox, benzo-ghi-perylene, and DEHP is recommended for the WWTP effluents.

Emerging microalgae-based technologies in biorefinery and risk assessment issues: Bioeconomy for sustainable development

Industrial wastewater treatment is of paramount importance considering the safety of the aquatic ecosystem and its associated health risk to humankind inhabiting near the water bodies. Microalgae-based technologies for remediation of environmental pollutants present avenues for bioenergy applications and production of value-added biochemicals having pharmaceutical, nutraceutical, antioxidants, carbohydrate, phenolics, long-chain multi-faceted fatty acids, enzymes, and proteins which are considered healthy supplements for human health. Such a wide range of products put up a good case for the biorefinery concept. Microalgae play a pivotal role in degrading complex pollutants, such as organic and inorganic contaminants thereby efficiently removing them from the environment. In addition, microalgal species, such as Botryococcus braunii, Tetraselmis suecica, Phaeodactylum tricornutum, Neochloris oleoabundans, Chlorella vulgaris, Arthrospira, Chlorella, and Tetraselmis sp., etc., are also reported for generation of value-added products. This review presents a holistic view of microalgae based biorefinery starting from cultivation and harvesting of microalgae, the potential for remediation of environmental pollutants, bioenergy application, and production of value-added biomolecules. Further, it summarizes the current understanding of microalgae-based technologies and discusses the risks involved, potential for bioeconomy, and outlines future research directions.

Removal of Nutrients and Pesticides from Agricultural Runoff Using Microalgae and Cyanobacteria

The use of pesticides in agriculture has ensured the production of different crops. However, pesticides have become an emerging public health problem for Latin American countries due to their excessive use, inadequate application, toxic characteristics, and minimal residue control. The current project evaluates the ability of two strains of algae (Chlorella and Scenedesmus sp.) and one cyanobacteria (Hapalosyphon sp.) to remove excess pesticides and other nutrients present in runoff water from rice production. Different concentrations of wastewater and carbon sources (Na2CO3 and NaHCO3) were evaluated. According to the results, all three strains can be grown in wastewater without dilution (100%), with a biomass concentration comparable to a synthetic medium. All three strains significantly reduced the concentration of NO3 and PO4 (95 and 85%, respectively), with no difference between Na2CO3 or NaHCO3. Finally, Chlorella sp. obtained the highest removal efficiency of the pesticide (Chlorpyrifos), followed by Scenedesmus and Hapalosyphon sp. (100, 75, and 50%, respectively). This work shows that it is possible to use this type of waste as an alternative source of nutrients to obtain biomass and metabolites of interest, such as lipids and carbohydrates, to produce biofuels.

Evaluation of an outdoor pilot-scale tubular photobioreactor for removal of selected pesticides from water

This work assesses the capacity of a microalgae-based system to remove three highly to medium polar pesticides typically found in freshwater: acetamiprid, bentazone, and propanil. Degradation of the pesticides was firstly studied individually at batch lab-scale reactors and abiotic and heated-killed controls were employed to clarify their removal pathways. At lab-scale, propanil and acetamiprid were completely removed after 7 days whereas bentazone was not removed. Four and two transformation products (TPs) were generated in the biodegradation process for acetamiprid and propanil, respectively. Then, the simultaneous removal of the pesticides was assessed in an outdoor pilot photobioreactor, operated with a hydraulic residence time of 8 days. During the steady-state, high removal efficiencies were observed for propanil (99%) and acetamiprid (71%). The results from batch experiments suggest that removal is mainly caused by algal-mediated biodegradation. Acetamiprid TPs raised throughout the operational time in the photobioreactor, while no propanil TP was detected at the pilot-scale. This suggests complete mineralization of propanil or residual formation of its TPs at concentrations below the analytical method detection limit. Aiming at biomass valorization, diverse microalgae harvesting methods were investigated for biomass concentration, and the effect of residual pesticides on the biogas yield was determined by biochemical methane potential tests. Anaerobic digestion was not inhibited by the pesticides as verified by the digestion performance. The results highlight the potential of microalgae-based systems to couple nutrient removal, biomass production, micropollutant biodegradation, and biofuel production.

Monitoring of pesticides in surface water, pesticides removal efficiency in drinking water treatment plant and potential health risk to consumers using Monte Carlo simulation in Behbahan City, Iran

Excessive application of pesticides to control pests and weeds leads to contaminating bodies of water and health problems for consumers. The present study was designed to investigate the concentration of pesticides in raw water originated from the Marun River as well as the treated water of the drinking water treatment plant in Behbahan City. The efficiency of each treatment process was evaluated. Moreover, the health risks caused by detectable pesticides for consumers of treated water were assessed. The target pollutants were extracted using droplet liquid-liquid microextraction and detected by a gas chromatograph-mass spectrophotometer. The results showed relatively high mean concentrations of organophosphate pesticides ranging from 0.87 to 3.229 μg/L in the river water and low concentrations of organochlorine pesticides, except for 1,3-dichloropropene with the concentration of 3.58 μg/L. Alachlor had a rather high concentration (2.44 μg/L) in the river water. The concentration of pesticides in the drinking water had been reduced to an acceptable amount. The major part of pesticides removal occurred in coagulation-flocculation and rapid sand filtration units (87 %) due to the hydrophobic nature of pesticides and the use of GAC in the filtration unit. Based on the risk assessment estimates, the total hazard quotient (THQ) for all the pesticides was much less than one. The value of THQ was higher in younger individuals and children for all the given pesticides. The highest value of THQ in children was 0.2 which was attributed to aldrin. Similarly, the carcinogenic risk (CR) of aldrin for children and teenagers was in the unsafe range (more than 10^-4) while the CR for other target compounds in all the age groups was negligible (10^-4-10^-6 or less). The high concentration of pesticides in the river water might be concerning and therefore selling and using pesticides, especially the banned ones, should be more regulated.

Microbial Technologies Employed for Biodegradation of Neonicotinoids in the Agroecosystem

Neonicotinoids are synthetic pesticides widely used for the control of various pests in agriculture throughout the world. They mainly attack the nicotinic acetylcholine receptors, generate nervous stimulation, receptor clot, paralysis and finally cause death. They are low volatile, highly soluble and have a long half-life in soil and water. Due to their extensive use, the environmental residues have immensely increased in the last two decades and caused many hazardous effects on non-target organisms, including humans. Hence, for the protection of the environment and diversity of living organism's the degradation of neonicotinoids has received widespread attention. Compared to the other methods, biological methods are considered cost-effective, eco-friendly and most efficient. In particular, the use of microbial species makes the degradation of xenobiotics more accessible fast and active due to their smaller size. Since this degradation also converts xenobiotics into less toxic substances, the various metabolic pathways for the microbial degradation of neonicotinoids have been systematically discussed. Additionally, different enzymes, genes, plasmids and proteins are also investigated here. At last, this review highlights the implementation of innovative tools, databases, multi-omics strategies and immobilization techniques of microbial cells to detect and degrade neonicotinoids in the environment.

Recent Progress and Prospects in Catalytic Water Treatment

Presently, conventional technologies in water treatment are not efficient enough to completely mineralize refractory water contaminants. In this context, the implementation of catalytic processes could be an alternative. Despite the advantages provided in terms of kinetics of transformation, selectivity, and energy saving, numerous attempts have not yet led to implementation at an industrial scale. This review examines investigations at different scales for which controversies and limitations must be solved to bridge the gap between fundamentals and practical developments. Particular attention has been paid to the development of solar-driven catalytic technologies and some other emerging processes, such as microwave assisted catalysis, plasma-catalytic processes, or biocatalytic remediation, taking into account their specific advantages and the drawbacks. Challenges for which a better understanding related to the complexity of the systems and the coexistence of various solid-liquid-gas interfaces have been identified.

Pesticide residues in drinking water, their potential risk to human health and removal options

The application of pesticides in agricultural and public health sectors has resulted in substantially contaminated water resources with residues in many countries. Almost no reviews have addressed pesticide residues in drinking water globally; calculated hazard indices for adults, children, and infants; or discussed the potential health risk of pesticides to the human population. The objectives of this article were to summarize advances in research related to pesticide residues in drinking water; conduct health risk assessments by estimating the daily intake of pesticide residues consumed only from drinking water by adults, children, and infants; and summarize options for pesticide removal from water systems. Approximately 113 pesticide residues were found in drinking water samples from 31 countries worldwide. There were 61, 31, and 21 insecticide, herbicide, and fungicide residues, respectively. Four residues were in toxicity class IA, 14 residues were in toxicity class IB, 55 residues were in toxicity class II, 17 residues were in toxicity class III, and 23 residues were in toxicity class IV. The calculated hazard indices (HIs) exceeded the value of one in many cases. The lowest HI value (0.0001) for children was found in Canada, and the highest HI value (30.97) was found in Egypt, suggesting a high potential health risk to adults, children, and infants. The application of advanced oxidation processes (AOPs) showed efficient removal of many pesticide classes. The combination of adsorption followed by biodegradation was shown to be an effective and efficient purification option. In conclusion, the consumption of water contaminated with pesticide residues may pose risks to human health in exposed populations.

Microalgae-based removal of contaminants of emerging concern: Mechanisms in Chlorella vulgaris and mixed algal-bacterial cultures

Incomplete removal of contaminants of emerging concern (CECs) has been reported for conventional wastewater treatment technologies. Microalgae-based treatment has recently gained interest thanks to simultaneous removal capacity of organic and inorganic compounds and potentially CECs. In this study, a lab-scale monoculture of Chlorella vulgaris and mixed microalgal-bacterial culture were compared in terms of removal of 28 CECs (bisphenols, 2018 EU Watch List substances, including neonicotinoids, pharmaceuticals, selected transformation products). The removal pathways in light and dark abiotic controls were also studied. Batch photobioreactors were run at hydraulic retention times of 11-12 days and CECs spiked at environmentally relevant concentrations (1-20 μg L^-1). The mixed culture was better at removing bisphenols, compared to C. vulgaris. Bisphenols' log K_ow was significant in removal pathways, where bisphenols with high log K_ow were removed abiotically while bisphenols with low log K_ow were mainly biodegraded. The removal degrees and the pathways of pharmaceuticals and EU Watch List substances were comparable between both cultures, showing no impact of log K_ow for most compounds; however, the removal with C. vulgaris was faster for some. High log K_ow was associated with high removal of estradiol in abiotic controls, showing the importance of adsorption onto biomass and suspended matter.

A lognormal model for evaluating maximum residue levels of pesticides in crops

To evaluate pesticide regulatory standards in agricultural crops, we introduced a regulatory modeling framework that can flexibly evaluate a population's aggregate exposure risk via maximum residue levels (MRLs) under good agricultural practice (GAP). Based on the structure of the aggregate exposure model and the nature of variable distributions, we optimized the framework to achieve a simplified mathematical expression based on lognormal variables including the lognormal sum approximation and lognormal product theorem. The proposed model was validated using Monte Carlo simulation, which demonstrates a good match for both head and tail ends of the distribution (e.g., the maximum error = 2.01% at the 99th percentile). In comparison with the point estimate approach (i.e., theoretical maximum daily intake, TMDI), the proposed model produced higher simulated daily intake (SDI) values based on empirical and precautionary assumptions. For example, the values at the 75th percentile of the SDI distributions simulated from the European Union (EU) MRLs of 13 common pesticides in 12 common crops were equal to the estimated TMDI values, and the SDI values at the 99th percentile were over 1.6-times the corresponding TMDI values. Furthermore, the model was refined by incorporating the lognormal distributions of biometric variables (i.e., food intake rate, processing factor, and body weight) and varying the unit-to-unit variability factor (VF) of the pesticide residues in crops. This ensures that our proposed model is flexible across a broad spectrum of pesticide residues. Overall, our results show that the SDI is significantly reduced, which may better reflect reality. In addition, using a point estimate or lognormal PF distribution is effective as risk assessments typically focus on the upper end of the distribution.

Removal and environmental risk assessment of contaminants of emerging concern from irrigation waters in a semi-closed microalgae photobioreactor

The present study evaluated the efficiency of a semi-closed, tubular, horizontal photobioreactor (PBR) to treat a mixture of irrigation and rural drainage water, focusing in the removal of different contaminants of emerging concern (CECs), and evaluating the environmental impact of the resulting effluent. Target CECs included pharmaceuticals, personal care products and flame retardants. Of the 13 compounds evaluated, 11 were detected in the feed water entering the PBR, and diclofenac (DCF) (1107 ng L^-1) and N,N-diethyl-toluamide (DEET) (699 ng L^-1) were those present at the greatest concentrations. The best removal efficiencies were achieved for the pharmaceuticals diazepam (94%), lorazepam (LZP) (83%) and oxazepam (OXA) (71%), and also for ibuprofen (IBU) (70%). For the rest of the CECs evaluated, attenuation was similar to that obtained after conventional wastewater treatment, ranging from basically no elimination (carbamazepine (CBZ) and tris-(2-chloroethyl) phosphate (TCEP)) to medium efficiencies (DCF and tributyl phosphate (TBP) (50%)). Environmental risk assessment based on hazard quotients (HQs) resulted in HQ values < 0.1 (no risk associated) for most of the compounds and most of the trophic levels considered. Values between 1 and 10 (moderate risk) were obtained for tonalide (AHTN) (fish) and CBZ (invertebrates). The most sensitive trophic level was green algae, whereas fish and aquatic plants were the most resilient. Our results suggest that microalgae-based treatments could become a green, cost-effective alternative to conventional wastewater treatment regarding the efficient elimination of these contaminants.

Nanoparticle Beads of Chitosan-Ethylene Glycol Diglycidyl Ether/Fe for the Removal of Aldrin

This article reports on the preparation of iron nanoparticles (FeNPs) supported in chitosan beads (Chi-EDGE-Fe) for removing aldrin from aqueous solutions. The FeNPs and Chi-EDGE-Fe beads were characterized by means of scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR), and the Mössbauer spectroscopy (MS) techniques. TEM, XRD, and MS showed that the FeNPs had core-shell structures consisting of a core of either Fe0 or Fe2B and a shell of magnetite. Furthermore, SEM images showed that Chi-EDGE-Fe beads were spherical with irregular surfaces and certain degrees of roughness and porosity, whilst the sorbent mean pore size was 204 nm, and the occluded iron nanoparticles in the chitosan material had diameters of 70 nm and formed agglomerates. The sorbent beads consisted of carbon, oxygen, chlorine, aluminum, silicon, and iron according to the SEM-EDS analysis. Functional groups such as O-H, C-H, -CH2, N-H, C-O, C-OH, and Fe-OH were detected in the FTIR spectra. In addition, a characteristic band appeared at about 1700 cm−1 after the sorption process involving aldrin. MS also showed that the iron nanoparticles in the beads probably oxidized into NPs of α-Fe2O3 as a result of the supporting process. The isotherm of the aldrin removal followed the Langmuir–Freundlich model and presented a maximum adsorption capacity of 74.84 mg/g, demonstrating that chitosan-Fe beads are promising sorbents for the removal of toxic pollutants in aqueous solutions.

Bioremediation of emerging micropollutants in irrigation water. The alternative of microalgae-based treatments

The present study evaluated the efficiency of a semi-closed horizontal tubular photobioreactor (PBR) at demonstrative scale to remove a total of 35 target compounds, including benzotriazoles, benzophenones, antibiotics and different pharmaceuticals present in irrigation water in a peri-urban rural area. This water run through an open channel and was a mixture of reclaimed wastewater from a nearby wastewater treatment plant (WWTP) and run-off from the different agricultural fields in the area. Most of the compounds studied are usually not fully eliminated during conventional wastewater treatment, which justifies the need to investigate alternative treatment strategies. A total of 21 of these compounds were detected in the irrigation water. Benzotriazoles were only partially removed after the microalgae treatment, with elimination rates similar to those of conventional WWTPs. The UV filter benzophenone-3 (BP3) showed variable removals, ranging from no elimination to 51%, whereas 4-methylbenzilidenecamphor (4MBC) was completely eliminated. Regarding pharmaceuticals, average removals were higher, in the range of 60-100%, with the exception of the antibiotics sulfamethoxazole (46%) and sulfapyridine, which was not removed. Despite the low biomass productivity of the PBR, parameters such as the size of the reactors, the specific mixed cultures developed and the high temperatures and pH in the closed system may account for the overall good results, The efficiency and sustainability of these systems make them a solid, feasible treatment choice.