Electrochemical determination of copper ions in spirit drinks using carbon paste electrode modified with biochar

Exploring wood-derived biochar potential for electrochemical sensing of fungicides mancozeb and maneb in environmental water samples

The sustainable material, biochar (BC) from a hardwood source, was synthesized via pyrolysis process at 400 °C (BC400) and 700 °C (BC700) and used as a modifier during the electrochemical sensor design. The prepared BCs were characterized by scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET) analysis, and elemental analysis (CHNS). The development of rapid analytical techniques for detecting pesticides employing a low-cost carbon paste electrode (CPE) modified with BC is a novel strategy to provide a sensitive response to water pollution. The prepared working electrodes (unmodified CPE, BC400-CPE, and BC700-CPE) were compared for selected fungicides mancozeb (MCZ) and maneb (MAN) sensing, and BC700-CPE provides the most favorable analytical response of target analytes. Cyclic voltammetric investigations revealed that the electrode reaction is irreversible and controlled by the adsorption of MCZ and MAN at the surface of the BC700-CPE, which led to an optimization of the differential pulse adsorptive stripping voltammetric (DP-AdSV) method. The obtained working linear concentration ranges were 25-2780 μg L-1 MCZ and 49-1840 μg L-1 MAN in Britton-Robinson buffer pH 7.0 using CPE modified with 10 % BC700. The evaluated limit of detection was 7.5 μg L-1 for MCZ and 15.0 μg L-1 for MAN. Investigated interferences did not significantly affect the MCZ and MAN oxidation signal intensity. The developed DP-AdSV method was successfully applied to determine selected fungicides in spiked river water and wastewater samples, with good recovery and reproducibility.

An L-cysteine based sensor for Cu2+ detection applicable for both environmental water and human plasma

A flexible electrochemical sensor with high sensitivity and specificity is developed using gold nanoparticles (AuNPs) and a reduced graphene oxide/molybdenum disulfide (rGo-MoS2) composite modified screen printed carbon electrode (SPCE), with L-cysteine (L-Cys) as a probe for Cu2+ target recognition. Owing to the AuNPs/rGo-MoS2, the electron transference ability is improved by increasing the specific surface area of the working electrode, and a high sensitivity is achieved. Meanwhile, the bidentate chelation of L-Cys to Cu2+ contributes to a good selectivity. Using differential pulse voltammetry (DPV) for spiked standard Cu2+, the test results show a dynamic range from 0.1 μM to 100 μM, a detection limit of 0.020 μM, and a high sensitivity of 1.190 μA μM-1. Furthermore, detection in both environmental water and human plasma samples demonstrates a wide applicability of this sensor in various matrices, and an excellent feasibility for environmental and clinical applications.

A ratiometric fluorescence and colorimetry dual-signal sensing strategy based on o-phenylenediamine and AuNCs for determination of Cu2+ and glyphosate

A ratiometric fluorescence sensing strategy has been developed for the determination of Cu2+ and glyphosate with high sensitivity and specificity based on OPD (o-phenylenediamine) and glutathione-stabilized gold nanoclusters (GSH-AuNCs). Water-soluble 1.75-nm size GSH-AuNCs with strong red fluorescence and maximum emission wavelength at 682 nm were synthesized using GSH as the template. OPD was oxidized by Cu2+, which produced the bright yellow fluorescence oxidation product 2,3-diaminophenazine (DAP) with a maximum fluorescence emission peak at 570 nm. When glyphosate existed in the system, the chelation between glyphosate and Cu2+ hindered the formation of DAP and reduced the fluorescence intensity of the system at the wavelength of 570 nm. Meanwhile, the fluorescence intensity at the wavelength of 682 nm remained basically stable. It exhibited a good linear relationship towards Cu2+ and glyphosate in water in the range 1.0-10 µM and 0.050-3.0 µg/mL with a detection limit of 0.547 µM and 0.0028 µg/mL, respectively. The method was also used for the semi-quantitative determination of Cu2+ and glyphosate in water by fluorescence color changes visually detected by the naked eyes in the range 1.0-10 µM and 0.30-3.0 µg/mL, respectively. The sensing strategy showed higher sensitivity, more obvious color changes, and better disturbance performance, satisfying with the detection demands of Cu2+ and glyphosate in environmental water samples. The study provides a reliable detection strategy in the environment safety fields.

Decorated graphene oxide with gold nanoparticles as a sensitive modified carbon paste electrode for simultaneous determination of tyrosine and uric acid

It is presented here as a simple, selective, rapid, low-cost, with a wide linear range method to simultaneously determine tyrosine and uric acid using a modified carbon paste electrode decorated with graphene oxide and gold nanoparticles (GO/AuNPs/MCPE). In order to characterize and evaluate the morphology and constituents of the nanostructures, X-ray diffraction spectroscopy, Transmission electron microscopes, Dynamic light scattering, Zeta potential, electrochemical impedance spectroscopy, and Voltammetry were employed. The current response on the surface of the modified electrode had a dynamic linear range relationship in the concentrations of 0.14-340.00 µmol L-1 and 0.06-141.00 µmol L-1 for tyrosine and uric acid, respectively, and the method detection limit (MDL) was 0.0060 µmol L-1 and 0.0037 µmol L-1, respectively. This modified electrode provided high stability, sensitivity, and acceptable reproducibility for voltammetric measurements of tyrosine and uric acid simultaneously in a biological matrix.

Development of cysteine-doped MnO2 quantum dots for spectrofluorimetric estimation of copper: applications in different matrices

Copper (Cu) plays a role in maintaining healthy nerve cells and the immune system. Osteoporosis is a high-risk factor for Cu deficiency. In the proposed research, unique green, fluorescent cysteine-doped MnO2 quantum dots (Cys@MnO2 QDs) were synthesized and assessed for the determination of Cu in different food and hair samples. The developed quantum dots were synthesized with the help of cysteine using a straightforward ultrasonic approach to create 3D fluorescent Cys@MnO2 QDs. The resulting QDs' morphological and optical characteristics were carefully characterized. By adding Cu ions, the intensity of fluorescence for the produced Cys@MnO2 QDs was found to be dramatically reduced. Additionally, the applicability of Cys@MnO2 QDs as a new luminous nanoprobe was found to be strengthened by the quenching effect grounded on the Cu-S bonding. The concentrations of Cu2+ ions were estimated within the range of 0.06 to 7.00 µg mL-1, with limit of quantitation equal to 33.33 ng mL-1 and detection limit equal to 10.97 ng mL-1. The Cys@MnO2 QD technique was applied successfully for the quantification of Cu in a variety of foods, including chicken meat, turkey, and tinned fish, as well as in human hair samples. The chance that this novel technique could be a useful tool for figuring out the amount of cysteine in bio-samples is increased by the sensing system's remarkable advantages, which include being rapid, simple, and economical.

A critical review on the assessment of the quality and authenticity of Tequila by different analytical techniques: Recent advances and perspectives

Currently, the authenticity and traceability of Tequila are determined in an inspection process carried out by the Tequila Regulatory Council. However, in recent years, the authorities have seized illegal alcoholic products that are marketed as Tequila without being so, making it necessary to strengthen the current methods of detecting counterfeiting and/or adulteration. Therefore, it is important to establish a review of the current analytical techniques that have been proposed to solve this problem. In this review, emphasis is placed on the analysis of the analytical techniques that have been used to consolidate a profile of authenticity and quality in Tequila, thus highlighting new auxiliary analytical techniques to the current verification process, establishing future validation opportunities in terms of international quality control. The use of isotopic ratios stands out as the most robust technique because it establishes the type of sugar source used and the maturation time of the manufacturing process.

Applications of New Generation Solvents for Extraction of Herbal Products Prior to Atomic and Molecular Analysis

In this review, an up to date and current knowledge of some of the green solvents, which includes supercritical fluids extraction (SFE), switchable polarity solvents (SPS), and natural deep eutectic solvents (NADES) are discussed with more emphasis on the extraction of active components of herbal products. Different scientific articles and books have been researched and reviewed to explain the applications of new generation solvents for extraction of herbal products prior to atomic and molecular analysis from the past until now. Currently, the most of techniques used in processing herbal products involve the use of extraction methods. Therefore, trends in extraction methods focuses mainly on finding reasonable solutions that minimizes the use of toxic solvents and allows the usage of renewable and green solvents from natural products, which ensure high quality and safe extracts. In future, SFE is definitely going to be on the industrial scale due to its numerous applications in the large scale especially for herbal, food, cosmetics and pharmaceutical products etc.

Biochar: An environmentally friendly platform for construction of a SARS-CoV-2 electrochemical immunosensor

Waste management is a key feature to ensure sustainable consumption and production patterns, and to combat the impacts of climate change. In this scenario, the production of biochar from different biomasses results in environmental and economic advantages. In this study, biochar was produced from sugarcane bagasse pyrolysis, to immobilize biomolecules, in order to assemble an electrochemical immunosensor to detect antibodies against SARS-CoV-2. For this, screen-printed carbon electrodes (SPCE) were modified with a dispersion of biochar and used to immobilize the receptor-binding-domain (RBD) against virus S-protein, through EDC/NHS crosslinking reaction. Under the best set of experimental conditions, negative and positive serum samples responses distinguished based on a cutoff value of 82.3 %, at a 95 % confidence level. The immunosensor showed selective behavior to antibodies against yellow fever and its performance was stable up to 7 days of storage. Therefore, biochar yielded from sugarcane bagasse is an ecofriendly material that can be used as a platform to immobilize biomolecules for construction of electrochemical biosensors.

Biochar derived carbonaceous material for various environmental applications: Systematic review

Biochar is the solid material produced from the carbonization of organic feedstock biomass. This material has several unique characteristics such as greater carbon content, good electrical conductivity, high stability and large surface area, which can be applied in several research areas such as generation of power and wastewater treatment. In connection with this, recently, the investigations on biochar significantly focus on the removal of toxic heavy metals since the biochar material is easily available and environmentally friendly. According to an environmental analytical device, biochar-derived carbonaceous material has been additionally applied to the synthesis of an effective, sensitive, and low-cost electrochemical sensor. Biochar with an assessment of electrochemical properties has engaged with different redox reactions in water. In this survey, electrochemical ways of behaving of biochar in light of the electrochemical structures were analytically compiled as well as the impact from biomass sources and manufacturing process including carbonization strategies, pre-treatment/changed techniques. This review emphasizes the various synthesis methods of biochar form organic feedstock, properties and different modulations of biochar for the bioremediation of heavy metals. This review study emphasizes the utilization of biochar as sensing platform and supercapacitor for electrode fabrication in electrochemical biosensor to enhance the remediation of toxic contaminants from water streams and by switching the less ecological traditional materials. Brief information on the techniques employed for packaging biochar as carbon electrode is summarized. Scope in the aspect of environmental concern of biochar, future challenges and prospects are proposed in detail.

A Novel Activated Biochar-Based Immunosensor for Rapid Detection of E. coli O157:H7

E. coli O157:H7, one of the major foodborne pathogens, can cause a significant threat to the safety of foods. The aim of this research is to develop an activated biochar-based immunosensor that can rapidly detect E. coli O157:H7 cells without incubation in pure culture. Biochar was developed from corn stalks using proprietary reactors and then activated using steam-activation treatment. The developed activated biochar presented an enhanced surface area of 830.78 m²/g. To develop the biosensor, the gold electrode of the sensor was first coated with activated biochar and then functionalized with streptavidin as a linker and further immobilized with biotin-labeled anti-E. coli polyclonal antibodies (pAbs). The optimum concentration of activated biochar for sensor development was determined to be 20 mg/mL. Binding of anti-E. coli pAbs with E. coli O157:H7 resulted in a significant increase in impedance amplitude from 3.5 to 8.5 kΩ when compared to an only activated biochar-coated electrode. The developed immunosensor was able to detect E. coli O157:H7 cells with a limit of detection of 4 log CFU/mL without incubation. Successful binding of E. coli O157:H7 onto an activated biochar-based immunosensor was observed on the microelectrode surface in scanning electron microscopy (SEM) images.

β-Cyclodextrin/CMK-8-Based Electrochemical Sensor for Sensitive Detection of Cu2

In this work, β-cyclodextrin (β-CD)/mesoporous carbon (CMK-8) nanocomposite was synthesized and used as an electrochemical sensing platform for highly sensitive and selective detection of Cu2+. The morphology and structure of β-CD/CMK-8 were characterized by scanning electron microscope (SEM) and X-ray diffraction (XRD). In addition, the dates from electrochemical impedance spectroscopy (EIS) and Cyclic voltammetry (CV) demonstrated that the β-CD/CMK-8 possessed a fast electronic transfer rate and large effective surface area. Besides this, the β-CD/CMK-8 composite displayed high enrichment ability toward Cu2+. As a result of these impressive features, the β-CD/CMK-8 modified electrode provided a wide linear response ranging from 0.1 ng·L-1 to 1.0 mg·L-1 with a low detection limit of 0.3 ng·L-1. Furthermore, the repeatability, reproducibility and selectivity of β-CD/CMK-8 towards Cu2+ were commendable. The sensor could be used to detect Cu2+ in real samples. All in all, this work proposes a simple and sensitive method for Cu2+ detection, which provides a reference for the subsequent detection of HMIs.

Recent Advances of Biochar-Based Electrochemical Sensors and Biosensors

In the context of accelerating the global realization of carbon peaking and carbon neutralization, biochar produced from biomass feedstock via a pyrolysis process has been more and more focused on by people from various fields. Biochar is a carbon-rich material with good properties that could be used as a carrier, a catalyst, and an absorbent. Such properties have made biochar a good candidate as a base material in the fabrication of electrochemical sensors or biosensors, like carbon nanotube and graphene. However, the study of the applications of biochar in electrochemical sensing technology is just beginning; there are still many challenges to be conquered. In order to better carry out this research, we reviewed almost all of the recent papers published in the past 5 years on biochar-based electrochemical sensors and biosensors. This review is different from the previously published review papers, in which the types of biomass feedstock, the preparation methods, and the characteristics of biochar were mainly discussed. First, the role of biochar in the fabrication of electrochemical sensors and biosensors is summarized. Then, the analytes determined by means of biochar-based electrochemical sensors and biosensors are discussed. Finally, the perspectives and challenges in applying biochar in electrochemical sensors and biosensors are provided.

Investigation of seawater mineral promoted pyrolysis at low temperature for improving the adsorption capabilities of biochar

Naturally abundant seawater mineral was employed to engineer banana pseudostem and bamboo biochars through pyrolysis at different low temperatures for improving their adsorption capabilities for methylene blue (MB) and tetracycline (TC). The adsorption capabilities were greatly enhanced as the biochars were pyrolyzed at 300 °C with 50/1 (mL/g) dosage of seawater to biomass. For instance, the engineered banana pseudostem biochar exhibited 8.00 and 6.54 times higher adsorption capabilities than the corresponding pristine biochar for MB (447.79 mg/g vs 55.96 mg/g) and TC (100.59 mg/g vs 16.75 mg/g) at 25 °C, respectively. The characterization results indicated that a large number of carboxylates, lactone acid salts, and alkoxides were generated on the engineered biochar and a high cation exchange capacity was gained. The adsorption of MB was mainly attributed to cation exchange complying with hydrogen bonding and electrostatic interaction, whereas the adsorption of TC was realized by hydrogen bonding and complexation.

Design and optimization of sensitive analytical spectrophotometric method for micro determination of copper(II) from e-waste by using of novel chromogenic extractant

In this article, a novel spectrophotometric reagent 1-(pyrimidine)-4, 4, 6-trimethyl-1,4-dihydropyrimidine-2-thiol [PTPT] has been synthesized for liquid-liquid extraction and spectrophotometric determination of copper(II). The as-synthesized ligand has been selectively forms stable complex with copper(II) in basic medium (pH 9.0), in presence of mild pyridine the extraction and color stability has found to be synergistically enhanced. The equilibrium time is 10 min for effective extraction of copper(II) from organic phase and absorbance of colored organic complex in carbon tetrachloride is measured spectrophotometrically at λ_max 615 nm against reagent blank. The ternary complex of Cu(II)-PTPT-Py having molar ratio 1:2:2 (M:L:Py) showed green colored complex. The main factors influencing the achievement of synergistic extraction; i.e. pH, ligand concentration, type and volume of the dispersive organic solvents, equilibrium time, synergent concentration and foreign ions were investigated. The Beer's law was obeyed in the concentration range 1-20 μg mL^-1 of copper(II) and optimum concentration range is evaluated by Ringbom's plot and it is found that 2.5-25 μg mL^-1. In presence of pyridine, molar absorptivity and Sandell's sensitivity of copper(II)-PTPT complex is 2.80 × 10³ L mol^-1 cm^-1 and 0.226 μg cm^-2, respectively and in absence of pyridine, molar absorptivity and Sandell's sensitivity of copper(II)-PTPT complex is 1.35 × 10³ L mol^-1 cm^-1 and 0.469 μg cm^-2, respectively. The stoichiometry of the copper(II)-PTPT-pyridine complex was calculated by slope ratio method, mole ratio method and Job's method of continuous variation and it has been found as 1:2:2. No significant effects of potentially interfering species i.e. cations and anions were observed. The optimized method was applied for the determination of copper(II) in binary, synthetic mixtures and successfully applied for determination of copper(II) from e-waste samples. The standard deviation (R.S.D.) is 0.11% for n = 5 repetition. The reliability of the developed method is confirmed by comparison of experimental results with atomic absorption spectrophotometer.

Selective detection of Cu2+ ions using a mercaptobenzothiazole disulphide modified carbon paste electrode and bismuth as adjuvant: a theoretical and electrochemical study

Bismuth adsorbed on the MBTS-modified surface facilitates the mass and charge transfer necessary for copper's selective sensing.

Green synthesis of walnut shell hydrochar, its antimicrobial activity and mechanism on some pathogens as a natural sanitizer

Hydrochar of waste walnut shells (WSH) was synthesized in the eco-friendly subcritical water medium (SWM) and its potential to fight against Klebsiella pneumoniae (K. pneumoniae), Staphylococcus aureus (S. aureus), Candida albicans (C. albicans) and Candida parapsilosis (C. parapsilosis) was investigated. Minimum Inhibitory Concentration (MIC) values of the WSH were 3.01 g/mL, 2.06 g/mL, 1.95 g/mL, and 3.12 g/mL for K. pneumoniae, S. aureus, C. albicans and C. parapsilosis, respectively. Survival of the pathogens was investigated by 3 min surface disinfection test exposure to WSH. While the highest inhibition was seen for C. parapsilosis (96.67%) on paper surface with 0.3 g/mL of bovine serum albumin (BSA), the lowest inhibition was determined for C. albicans (6.44%) on the plastic glass surface with 3 g/mL of BSA. An increase in protein, DNA, and potassium ion (K⁺) leakage was observed after microorganisms were incubated with WSH. This study provided an experimental basis for the practical application of WSH as a natural sanitizer agent.

A color reaction for the determination of Cu2+ in distilled beverages employing digital imaging

In this work, we describe for the first time the synthesis of a thiocarbazone for the selective determination of Cu²⁺ in distilled beverages. The method was based on the complexation reaction of Cu²⁺ with the thiocarbazone, and the colored product was analyzed using a smartphone application. The thiocarbazone reacts with Cu²⁺ to form a 1:1 (metal:ligand) complex. The Cu²⁺ complex was characterized by UV, IR and NMR spectral analyses. The proposed reaction yields a yellow color, and therefore, channel B of the RGB system was used in the analysis. After optimizing the reaction conditions, an analytical curve was obtained to determine Cu²⁺ concentrations ranging between 0.25 and 6.75 mg L^-1; the use of 400 μL sample volumes led to a relative standard deviation (n = 5) of 3.2% and a detection limit of 0.18 mg L^-1. Recovery experiments were performed with sugar cane spirits, whiskies and tequilas to evaluate the accuracy of the method, and the recovery obtained ranged from 80.5 to 112.2%.

Electronic Eye Based on RGB Analysis for the Identification of Tequilas

The present work reports the development of a biologically inspired analytical system known as Electronic Eye (EE), capable of qualitatively discriminating different tequila categories. The reported system is a low-cost and portable instrumentation based on a Raspberry Pi single-board computer and an 8 Megapixel CMOS image sensor, which allow the collection of images of Silver, Aged, and Extra-aged tequila samples. Image processing is performed mimicking the trichromatic theory of color vision using an analysis of Red, Green, and Blue components (RGB) for each image's pixel. Consequently, RGB absorbances of images were evaluated and preprocessed, employing Principal Component Analysis (PCA) to visualize data clustering. The resulting PCA scores were modeled with a Linear Discriminant Analysis (LDA) that accomplished the qualitative classification of tequilas. A Leave-One-Out Cross-Validation (LOOCV) procedure was performed to evaluate classifiers' performance. The proposed system allowed the identification of real tequila samples achieving an overall classification rate of 90.02%, average sensitivity, and specificity of 0.90 and 0.96, respectively, while Cohen's kappa coefficient was 0.87. In this case, the EE has demonstrated a favorable capability to correctly discriminated and classified the different tequila samples according to their categories.

Voltammetric Determination of Lead and Copper in Wine by Modified Glassy Carbon Electrode

This paper describes the determination of Pb and Cu with a Nafion-modified glassy carbon electrode and MnCo₂O₄ nanoparticles as working electrode for anodic stripping voltammetry. Pb and Cu were accumulated in HCl/KCl (0.1 mol dm^-3) at a potential of -1.4 V (vs. Ag/AgCl electrode) for 480 s, followed by a linear sweep anodic stripping voltammetry (ASV) scan from -1.0 to +0.5 V. Under optimum conditions, the calibration curves were linear in the range of 0.01 - 8 and 0.01 - 5 mg dm^-3 for Pb and Cu, respectively. Effect of sample dilution, accumulation time and potential were optimized. A study of interfering substances was performed. A significant increase in current was obtained at the modified electrode in comparison with the bare glassy carbon electrode. The modified electrode was successfully applied for determination of Pb and Cu in wine samples after a simple preparation procedure. Pb and Cu content in wine was used for estimation of the target hazard quotient (THQ) values for minimal and maximal levels of the metals.

A new highly selective colorimetric Schiff base chemosensor for determining the copper content in artisanal cachaças

This work demonstrated the feasibility of applying the Schiff base 5-bromo-2-salicyl-beta-alanine as a colorimetric chemosensor for the spectrophotometric quantification of the copper content in artisanal cachaças. For this, the experimental conditions were optimized to obtain an efficient, sensitive, reversible, and highly selective chemosensor to Cu²⁺ ions. The complex stoichiometry was 1:1, with a formation constant of 5.82 × 10² L mol^-1 and molar absorptivity of 5.82 × 10³ mol L^-1 cm^-1. Then, a spectrophotometric analytical method was developed and validated according to the Brazilian legislation. The linearity of the analytical curve was demonstrated by ANOVA, at a confidence level of 95%. The limits of detection and quantification were 0.0659 and 0.200 mg L^-1, respectively. The coefficients of variation for both the intra- and inter-day precisions were lower than 3.83%, and the accuracy presented a mean recovery of 100.55 ± 2.87%. The absence of a matrix effect was confirmed by the standard addition method, and the copper content in three artisanal cachaças from different geographical origins was estimated as lower than 2.93 mg L^-1. This result was in accordance with the Brazilian legislation but reinforces the need to carry out stricter quality control to achieve exportation standards. Therefore, the proposed method can be considered a simple, selective, linear, precise, and accurate tool that involves only a simple complexation reaction through the addition of the chemosensor solution in a buffered medium. As a consequence, the simplicity, practicality, rapidity, and low cost of synthesis of the proposed Schiff base chemosensor are highlighted.

Electrochemical immunosensor with Cu(I)/Cu(II)-chitosan-graphene nanocomposite-based signal amplification for the detection of newcastle disease virus

An electrochemical immunoassay for the ultrasensitive detection of Newcastle disease virus (NDV) was developed using graphene and chitosan-conjugated Cu(I)/Cu(II) (Cu(I)/Cu(II)-Chi-Gra) for signal amplification. Graphene (Gra) was used for both the conjugation of an anti-Newcastle disease virus monoclonal antibody (MAb/NDV) and the immobilization of anti-Newcastle disease virus polyclonal antibodies (PAb/NDV). Cu(I)/Cu(II) was selected as an electroactive probe, immobilized on a chitosan-graphene (Chi-Gra) hybrid material, and detected by differential pulse voltammetry (DPV) after a sandwich-type immune response. Because Gra had a large surface area, many antibodies were loaded onto the electrochemical immunosensor to effectively increase the electrical signal. Additionally, the introduction of Gra significantly increased the loading amount of electroactive probes (Cu(I)/Cu(II)), and the electrical signal was further amplified. Cu(I)/Cu(II) and Cu(I)/Cu(II)-Chi-Gra were compared in detail to characterize the signal amplification ability of this platform. The results showed that this immunosensor exhibited excellent analytical performance in the detection of NDV in the concentration range of 10^0.13 to 10^5.13 EID₅₀/0.1 mL, and it had a detection limit of 10^0.68 EID₅₀/0.1 mL, which was calculated based on a signal-to-noise (S/N) ratio of 3. The resulting immunosensor also exhibited high sensitivity, good reproducibility and acceptable stability.

Simultaneous metal determination in artisanal cachaça by using voltammetry and multivariate calibration

In this study, square wave anodic stripping voltammetry using two different types of electrodes (carbon nanotube electrode and graphite electrode) was combined with chemometric methods - partial least squares (PLS) and artificial neural networks (ANN) for determining copper, zinc, cadmium and lead in cachaça. The objectives were comparison of methods developed and the verification of the quality of artisanal cachaças in terms of metal content. For the development of the methodology, inductively coupled plasma optical emission spectrometry (ICP OES) was used as reference technique. The performance of multivariate models obtained was evaluated by the coefficient of determination (R²) and root mean square error of prediction (RMSEP). F test was utilized for comparing methods at confidence level of 95%. Better results were observed by using carbon nanotube electrode regardless of the multivariate method proposed. The methodology is simple, fast, and inexpensive and it can be used in quality control laboratories.

Cu(II) Ion Adsorption by Aniline Grafted Chitosan and Its Responsive Fluorescence Properties

The detection and removal of heavy metal species in aquatic environments is of continued interest to address ongoing efforts in water security. This study was focused on the preparation and characterization of aniline grafted chitosan (CS-Ac-An), and evaluation of its adsorption properties with Cu(II) under variable conditions. Materials characterization provides support for the grafting of aniline onto chitosan, where the kinetic and thermodynamic adsorption properties reveal a notably greater uptake (>20-fold) of Cu(II) relative to chitosan, where the adsorption capacity (Q_m) of CS-Ac-An was 106.6 mg/g. Adsorbent regeneration was demonstrated over multiple adsorption-desorption cycles with good uptake efficiency. CS-Ac-An has a strong fluorescence emission that undergoes prominent quenching at part per billion levels in aqueous solution. The quenching process displays a linear response over variable Cu(II) concentration (0.05–5 mM) that affords reliable detection of low level Cu(II) levels by an in situ “turn-off” process. The tweezer-like chelation properties of CS-Ac-An with Cu(II) was characterized by complementary spectroscopic methods: IR, NMR, X-ray photoelectron (XPS), and scanning electron microscopy (SEM). The role of synergistic effects are inferred among two types of active adsorption sites: electron rich arene rings and amine groups of chitosan with Cu(II) species to afford a tweezer-like binding modality.

Multi-walled carbon nanotubes functionalized with bathocuproinedisulfonic acid: analytical applications for the quantification of Cu(II)

This work reports the successful non-covalent functionalization of multi-walled carbon nanotubes (MWCNTs) with bathocuproinedisulfonic acid (BCS) and the analytical application of the resulting dispersion (MWCNTs-BCS) to develop an electrochemical sensor for Cu(II) quantification. The sensor was obtained by casting glassy carbon electrodes (GCEs) with MWCNTs-BCS. The sensing mechanism was based on the open circuit preconcentration of Cu(II) at the electrode surface by complexation of Cu(II) through the phenanthroline ring nitrogen of the BCS that supports the MWCNTs, the reduction of the preconcentrated Cu(II), and final differential pulse voltammetry-anodic stripping in 0.020 M acetate buffer, pH 5.00. The sensitivity of the sensor was (2.73 ± 0.08) μA μM^-1, with a linear range between 5.0 × 10^-7 M and 6.0 × 10^-6 M, a detection limit of 0.15 μM (9.5 μg L^-1), and reproducibility of 6.2% using the same dispersion and 7.1% using three different MWCNTs-BCS dispersions. The quantification of Cu(II) was highly selective even in the presence of As³⁺, Cr³⁺, Cd²⁺, Ni²⁺, Pb²⁺, Co²⁺, Zn²⁺, Fe²⁺, Hg²⁺, Rh, Ir, and Ru. The proposed sensor was successfully used for quantifying Cu(II) in tap water. Graphical abstract.

A Review of Non-Soil Biochar Applications

Biochar is the solid residue that is recovered after the thermal cracking of biomasses in an oxygen-free atmosphere. Biochar has been used for many years as a soil amendment and in general soil applications. Nonetheless, biochar is far more than a mere soil amendment. In this review, we report all the non-soil applications of biochar including environmental remediation, energy storage, composites, and catalyst production. We provide a general overview of the recent uses of biochar in material science, thus presenting this cheap and waste-derived material as a high value-added and carbonaceous source.

Development of dual function polyamine-functionalized carbon dots derived from one step green synthesis for quantitation of Cu2+ and S2- ions in complicated matrices with high selectivity

The study of biologically important Cu²⁺ and S^2- ions has drawn great attention in the recent years since an abnormal level of these ions is an indication for health impairment. Therefore, a reliable strategy for effective fluorescence determination of Cu²⁺ and S^2- ions was developed. Simply, the method based on economical plant-dependent thermolysis procedure for efficient green synthesis of water dispersible luminescent polyamine-based carbon dots (PA@C-dots) utilizes Vitis vinifera juice as precursor with a high quantum yield (32.1%) and good photo-stability. The fluorescent PA@C-dots were characterized by different spectroscopical, physical, and structural techniques. Furthermore, the synthesized PA@C-dots can be used as an efficient dual functional fluorescent probe for the sensitive and selective estimation of Cu²⁺ and S^2- ions. The incorporation of Cu²⁺ ions and their adsorption on the surface of PA@C-dot skeleton leads to the respectable fluorescence quenching of C-dots (turn-off mode). The Cu²⁺-PA@C-dot was found to be sensitive to S^2- ions. The addition of S^2- recovers the fluorescence (turn-on mode) of Cu²⁺-PA@C-dots, thanks to its capacity for withdrawing Cu²⁺ from the shell of PA@C-dots. Fluorescence quenching in the range of 0.07-60 μM Cu²⁺ was obtained with LOD and LOQ of 0.02 and 0.066 μM, respectively. Sulfide detection provides linearity in the range of 0.8 to 95 μM with LOD and LOQ of 0.24 and 0.79 μM, respectively. The optimal excitation and emission wavelengths for all experiments are 435 nm and 498 nm, respectively. Experiment results elucidate that the proposed method is suitable for Cu²⁺and S^2- ion detection in environmental water samples. Graphical abstract Green synthesis of polyamine-functionalized nanoprobe by thermolysis method from plant source as bifunctional sensing platform for determination of Cu²⁺ and S^2- in environmental water samples.

An OFF-ON detection method for copper(ii) ions using a AgAu-NG nanocomposite modified electrode

An OFF-ON detection method for Cu²⁺ was developed at the AgAu bimetallic nanoparticle decorated nitrogen-doped graphene (AgAu-NG) nanocomposite modified electrode. The measurement was based on the copper-catalyzed oxidation of cysteamine (Cys) to regulate the oxidation peak current of Ag. In the absence of Cu²⁺, Cys can bind to the surface of AgAu-NG via the Ag-S or Au-S bond, thus leading to an obvious decrease of the oxidation peak current of Ag. However, in the presence of Cu²⁺, Cu²⁺ can greatly catalyze the oxidation of Cys by dissolved O₂ to form cystamine, which would fall off the surface of AgAu-NG nanocomposites, leading to the partial recovery of the oxidation peak current of Ag. With the increase in the concentration of Cu²⁺, the oxidation peak current of Ag in the presence of Cys increases accordingly. So, the concentration of Cu²⁺ can be measured. By using the optimum conditions, this method can detect Cu²⁺ concentrations down to 0.3 nM (S/N = 3) with a linear response range of 1 nM-1 mM. Furthermore, this method was applied to determine Cu²⁺ concentrations in river water samples and showed excellent analytical performance.

Quick electrochemical immunoassay for hantavirus detection based on biochar platform

This work describes the first method using biochar (BC) as carbonaceous platform for immunoassay application. BC is a highly functionalized material obtained through biomass pyrolysis under controlled conditions. Due to the highly functionalized surface, covalent binding between BC and biomolecules can be performed by EDC/NHS conjugation. The application of the modified electrode was done with Hantavirus, that are etiologic agents mainly transmitted by wild rodents. Among its pathologies Hantavirus Cardiopulmonary Syndrome (HCPS) arises at Americas, caused by Hantavirus Araucária and reaches 40% lethality. The diagnostic is based on the presence of specific hantavirus nucleoprotein (Np), under viremic condition or IgG2b antibodies (Ab), during first symptoms. The results presented a device sensitivity of 5.28 μA dec^-1 and a LOD of 0.14 ng mL^-1 to the Np detection, ranging from 5.0 ng mL^-1 to 1.0 μg mL^-1, the Ab detection works as qualitative type sensor above 200 ng mL^-1. Both sensors were evaluated its selectivity and serum samples; selectivity against Gumboro disease, VP2 protein, and antibody IgG2a against Yellow fever disease (YF), respectively. So, the devices here proposed are promising tool suitable for both rodent and human hantavirus clinical surveys.

An "off-on" fluorescent sensor for copper ion using graphene quantum dots based on oxidation of l-cysteine

A simple and highly efficient "off-on" fluorescent sensor based on grapheme quantum dots (GQDs) for Cu²⁺ was developed. In this sensing platform, the fluorescence of GQDs was quenched in the presence of 2,4-dinitrophenylcysteine (DNPC), which is the reaction product of 1-chloro-2,4-dinitrobenzene (CDNB) and l-cysteine, owing to the spectral overlap between the absorption of DNPC and the excitation of GQDs. In the presence of Cu²⁺, l-cysteine was catalytically oxidized to l-cystine by O₂, resulting in the reduction of DNPC. Thus, the fluorescence of GQDs was recovery. Based on this, the fluorescent detection of Cu²⁺ could be achieved. The proposed sensing strategy offered a selective identification of Cu²⁺ with a detection limit of 4.5 nM. Additionally, the practical application of this assay for Cu²⁺ determination in real water samples was also demonstrated.