Influence of Sr-doping on structural, optical and photocatalytic properties of synthesized Ca3(PO4)2

Addressing the synchronized impact of a novel strontium titanium over copolymerized carbon nitride for proficient solar-driven hydrogen evolution

Currently, novel technologies are highly prerequisite as an outstanding approach in the field of photocatalytic water splitting (PWS). Previous research has shown that copolymerization technology could improve the photocatalytic performance of pristine carbon nitride (CN) more efficiently. As this technology further allows the charge carrier recombination constraints, due to novel monomer-incorporated highly abundant surface-active sites of metals in polymeric carbon nitride-based heterojunction. However, in present study, a novel previously unexplored thiophenedicarboxaldehyde (TAL) conjugated, strontium-titanium (SrTiO3) induced and CN based heterojunction, i.e., SrTiO3/CN-TAL10.0, was prepared for solar-driven hydrogen evolution reaction (HER). This heterojunction effectively enables the proficient isolation of photoinduced charge carriers and enhanced the charge transport over the surface junction, by enhancing the optical absorption range and average lifetime of photogenerated charges. The incorporation of TAL within the structure of CN via copolymerization highly increases the photocatalytic activity, as well as maintaining its photostability performance. The SrTiO3 concentration and the proportion of TAL among CN can be precisely controlled to provide the optimal photocatalytic efficiency with a maximum HER of 285.9 µmol/h under visible light (λ = 420 nm). Based on these results, our optical analysis shows that coupling of SrTiO3 and TAL monomer in the structure of CN considerably reduce the band gap of superior sample from (3.42 to 2.66 eV), thereby, signifying the outstanding photocatalytic performance of SrTiO3/CN-TAL10.0. Thus, this study provide a new guideline in order to develop the multidimensional photocatalysts with proper functioning for sustainable energy conversion and production.

Ba3(PO4)2 Photocatalyst for Efficient Photocatalytic Application

Barium phosphate (Ba3(PO4)2) is a class of material that has attracted significant attention thanks to its chemical stability and versatility. However, the use of Ba3(PO4)2 as a photocatalyst is scarcely reported, and its use as a photocatalyst has yet to be reported. Herein, Ba3(PO4)2 nanoflakes synthesis is optimized using sol-gel and hydrothermal methods. The as-prepared Ba3(PO4)2 powders are investigated using physicochemical characterizations, including XRD, SEM, EDX, FTIR, DRS, J-t, LSV, Mott-Schottky, and EIS. In addition, DFT calculations are performed to investigate the band structure. The oxidation capability of the photocatalysts is investigated depending on the synthesis method using rhodamine B (RhB) as a pollutant model. Both Ba3(PO4)2 samples prepared by the sol-gel and hydrothermal methods display high RhB photodegradation of 79% and 68%, respectively. The Ba3(PO4)2 obtained using the sol-gel process exhibits much higher stability under light excitation after four regeneration cycles. The photocatalytic oxidation mechanism is proposed based on the active species trapping experiments where O2 •‒ is the most reactive species. The finding shows the promising potential of Ba3(PO4)2 photocatalysts and opens the door for further investigation and application in various photocatalytic applications.

Cube-shaped Cobalt-doped zinc oxide nanoparticles with increased visible-light-driven photocatalytic activity achieved by green co-precipitation synthesis

From the perspective of environmental protection, the highly efficient degradation of antibiotics and organic dyes in wastewater needs to be tackled as soon as possible. In this study, an ecofriendly and green cube-shaped cobalt-doped zinc oxide nanoparticles (Co-ZnO NPs) photocatalyst using Pterocladia Capillacea (P. Capillacea) water extract loaded with 5, 10, and 15% cobalt ions were formed via co-precipitation process to degrade antibiotics. The prepared Co-ZnO NPs were tested as a photocatalyst for the photodegradation of ciprofloxacin (CIPF) in the presence of a visible LED-light source. Co-ZnO NPs have been obtained through the co-precipitation method in the presence of P. Capillacea extract as a green capping agent and reducing agent, for the first time. Several characterization techniques including FTIR, XRD, BET, XPS, TEM, EDX, SEM, TGA and DRS UV-Vis spectroscopy were applied to study the prepared Co-ZnO NPs. XRD results suggested that the average size of these NPs ranged between 42.82 and 46.02 nm with a hexagonal wurtzite structure. Tauc plot shows that the optical energy bandgap of ZnO NPs (3.19 eV) gradually decreases to 2.92 eV by Co doping. Examinations showed that 5% Co-ZnO NPs was the highest efficient catalyst for the CIPF photodegradation when compared with ZnO NPs and other 10 and 15% Co-ZnO NPs. A 10 mg/L solution of CIPF was photo-degraded (100%) within the first 15 min irradiation. The kinetics showed that the first-order model is suitable for displaying the rate of reaction and amount of CIPF elimination with R2 = 0.952. Moreover, central composite design optimization of the 5% Co-doped ZnO NPs was also investigated.

State, synthesis, perspective applications, and challenges of Graphdiyne and its analogues: A review of recent research

Carbon materials technology provides the possibility of synthesizing low-cost, outstanding performance replacements to noble-metal catalysts for long-term use. Graphdiyne (GDY) is a carbon allotrope with an extremely thin atomic thickness. It consists of carbon elements, that are hybridized with both sp. and sp2, resulting in a multilayered two-dimensional (2D) configuration. Several functional models suggest, that GDY contains spontaneously existing band structure with Dirac poles. This is due to the non-uniform interaction among carbon atoms, which results from various fusions and overlapping of the 2pz subshell. Unlike other carbon allotropes, GDY has Dirac cone arrangements, that in turn give it inimitable physiochemical characteristics. These properties include an adjustable intrinsic energy gap, high speeds charging transport modulation efficiency, and exceptional conductance. Many scientists are interested in such novel, linear, stacked materials, including GDY. As a result, organized synthesis of GDY has been pursued, making it one of the first synthesized GDY materials. There are several methods to manipulate the band structure of GDY, including applying stresses, introducing boron/nitrogen loading, utilizing nanowires, and hydrogenations. The flexibility of GDY can be effectively demonstrated through the formation of nano walls, nanostructures, nanotube patterns, nanorods, or structured striped clusters. GDY, being a carbon material, has a wide range of applications owing to its remarkable structural and electrical characteristics. According to subsequent research, the GDY can be utilized in numerous energy generation processes, such as electrochemical water splitting (ECWS), photoelectrochemical water splitting (PEC WS), nitrogen reduction reaction (NRR), overall water splitting (OWS), oxygen reduction reaction (ORR), energy storage materials, lithium-Ion batteries (LiBs) and solar cell applications. These studies suggested that the use of GDY holds significant potential for the development and implementation of efficient, multimodal, and intelligent catalysts with realistic applications. However, the limitation of GDY and GDY-based composites for forthcoming studies are similarly acknowledged. The objective of these studies is to deliver a comprehensive knowledge of GDY and inspire further advancement and utilization of these unique carbon materials.

Photocatalytic Properties and Chemical Durability of CaO-B2O3-V2O5 Borovanadate Glasses

The aim of this paper is to investigate the photocatalytic properties and chemical durability of the CaO-B2O3-V2O5 glasses system. The latter were synthesized by the melt-quenching technique. The amorphous nature of the prepared borovanadate glasses has been confirmed with X-ray diffraction. The chemical durability measured from their weights before and after immersion in deionized water and hydrochloric acid indicated that replacing V2O5 with B2O3 improved the chemical durability. The observed increases in chemical durability might be explained by the increase in the glass transition temperature, due to stronger bonding in the structural network. The photocatalytic performance was assessed by the degradation of methylene blue (MB) dye under irradiation, and the evolution of dye degradation was analyzed by UV-visible spectrometry. The vanadium content in the glass, the amount of catalyst, and the initial dye concentration showed a variable effect on the degradation of the MB dye. The photodegradation of methylene blue by the photocatalysts was found to follow pseudo-first-order rate kinetics. The photocatalytic activity for all the prepared photocatalysts showed a higher degradation performance, and the results indicated that 40 CaO-30 B2O3-30 V2O5 has the highest removal efficiency of about 99% in 180 min.

Ternary Polyaniline@Bi2O3-BiOCl Nanocomposites as Innovative Highly Active Photocatalysts for the Removal of the Dye under Solar Light Irradiation

Ternary PANI@Bi₂O₃-BiOCl nanocomposites were successfully synthesized during the oxidative polymerization of aniline monomer in the presence of Bi₂O₃. PANI@Bi₂O₃-BiOCl nanocomposites were characterized by several analytical techniques, including X-ray diffraction (XRD), Fourier Transform Infrared spectroscopy (FTIR), N₂ physisorption, UV-Vis Diffuse reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS). The effective PANI-semiconductor interaction promotes the fast separation and transfer of photogenerated electrons and holes, enhancing the photocatalytic efficiency of the materials towards methylene blue (MB) degradation under solar light irradiation. The best results were obtained by 0.5%PANI@Bi₂O₃-BiOCl, leading to 80% MB degradation in 2 h, four times higher than pristine Bi₂O₃-BiOCl. Moreover, 0.5%PANI@Bi₂O₃-BiOCl maintained stable photocatalytic performances for four cycles without significant activity loss. Various scavengers (isopropyl alcohol, formic acid, and benzoquinone) were used to identify the active species by trapping holes and radicals generated during the photocatalytic degradation process. Finally, a probable photocatalytic mechanism of PANI@Bi₂O₃-BiOCl photocatalyst was suggested.

Recent Advances and Future Perspectives of Metal-Based Electrocatalysts for Overall Electrochemical Water Splitting

Recently, the growing demand for a renewable and sustainable fuel alternative is contingent on fuel cell technologies. Even though it is regarded as an environmentally sustainable method of generating fuel for immediate concerns, it must be enhanced to make it extraordinarily affordable, and environmentally sustainable. Hydrogen (H₂ ) synthesis by electrochemical water splitting (ECWS) is considered one of the foremost potential prospective methods for renewable energy output and H₂ society implementation. Existing massive H₂ output is mostly reliant on the steaming reformation of carbon fuels that yield CO₂ together with H₂ and is a finite resource. ECWS is a viable, efficient, and contamination-free method for H₂ evolution. Consequently, developing reliable and cost-effective technology for ECWS was a top priority for scientists around the globe. Utilizing renewable technologies to decrease total fuel utilization is crucial for H₂ evolution. Capturing and transforming the fuel from the ambient through various renewable solutions for water splitting (WS) could effectively reduce the need for additional electricity. ECWS is among the foremost potential prospective methods for renewable energy output and the achievement of a H₂ -based economy. For the overall water splitting (OWS), several transition-metal-based polyfunctional metal catalysts for both cathode and anode have been synthesized. Furthermore, the essential to the widespread adoption of such technology is the development of reduced-price, super functional electrocatalysts to substitute those, depending on metals. Many metal-premised electrocatalysts for both the anode and cathode have been designed for the WS process. The attributes of H₂ and oxygen (O₂ ) dynamics interactions on the electrodes of water electrolysis cells and the fundamental techniques for evaluating the achievement of electrocatalysts are outlined in this paper. Special emphasis is paid to their fabrication, electrocatalytic performance, durability, and measures for enhancing their efficiency. In addition, prospective ideas on metal-based WS electrocatalysts based on existing problems are presented. It is anticipated that this review will offer a straight direction toward the engineering and construction of novel polyfunctional electrocatalysts encompassing superior efficiency in a suitable WS technique.

A Targeted Review of Current Progress, Challenges and Future Perspective of g-C3 N4 based Hybrid Photocatalyst Toward Multidimensional Applications

The increasing demand for searching highly efficient and robust technologies in the context of sustainable energy production totally rely onto the cost-effective energy efficient production technologies. Solar power technology in this regard will perceived to be extensively employed in a variety of ways in the future ahead, in terms of the combustion of petroleum-based pollutants, CO₂ reduction, heterogeneous photocatalysis, as well as the formation of unlimited and sustainable hydrogen gas production. Semiconductor-based photocatalysis is regarded as potentially sustainable solution in this context. g-C₃ N₄ is classified as non-metallic semiconductor to overcome this energy demand and enviromental challenges, because of its superior electronic configuration, which has a median band energy of around 2.7 eV, strong photocatalytic stability, and higher light performance. The photocatalytic performance of g-C₃ N₄ is perceived to be inadequate, owing to its small surface area along with high rate of charge recombination. However, various synthetic strategies were applied in order to incorporate g-C₃ N₄ with different guest materials to increase photocatalytic performance. After these fabrication approaches, the photocatalytic activity was enhanced owing to generation of photoinduced electrons and holes, by improving light absorption ability, and boosting surface area, which provides more space for photocatalytic reaction. In this review, various metals, non-metals, metals oxide, sulfides, and ferrites have been integrated with g-C₃ N₄ to form mono, bimetallic, heterojunction, Z-scheme, and S-scheme-based materials for boosting performance. Also, different varieties of g-C₃ N₄ were utilized for different aspects of photocatalytic application i. e., water reduction, water oxidation, CO₂ reduction, and photodegradation of dye pollutants, etc. As a consequence, we have assembled a summary of the latest g-C₃ N₄ based materials, their uses in solar energy adaption, and proper management of the environment. This research will further well explain the detail of the mechanism of all these photocatalytic processes for the next steps, as well as the age number of new insights in order to overcome the current challenges.

Recent Advancement in Rational Design Modulation of MXene: A Voyage from Environmental Remediation to Energy Conversion and Storage

Use of MXenes (Ti₃ C₂ T_x ), which belongs to the family of two-dimensional transition metal nitrides and carbides by encompassing unique combination of metallic conductivity and hydrophilicity, is receiving tremendous attention, since its discovery as energy material in 2011. Owing to its precursor selective chemical etching, and unique intrinsic characteristics, the MXene surface properties are further classified into highly chemically active compound, which further produced different surface functional groups i. e., oxygen, fluorine or hydroxyl groups. However, the role of surface functional groups doesn't not only have a significant impact onto its electrochemical and hydrophilic characteristics (i. e., ion adsorption/diffusion), but also imparting a noteworthy effect onto its conductivity, work function, electronic structure and properties. Henceforth, such kind of inherent chemical nature, robust electrochemistry and high hydrophilicity ultimately increasing the MXene application as a most propitious material for overall environment-remediation, electrocatalytic sensors, energy conversion and storage application. Moreover, it is well documented that the role of MXenes in all kinds of research fields is still on a progress stage for their further improvement, which is not sufficiently summarized in literature till now. The present review article is intended to critically discuss the different chemical aptitudes and the diversity of MXenes and its derivates (i. e., hybrid composites) in all aforesaid application with special emphasis onto the improvement of its surface characteristics for the multidimensional application. However, this review article is anticipated to endorse MXenes and its derivates hybrid configuration, which is discussed in detail for emerging environmental decontamination, electrochemical use, and pollutant detection via electrocatalytic sensors, photocatalysis, along with membrane distillation and the adsorption application. Finally, it is expected, that this review article will open up new window for the effective use of MXene in a broad range of environmental remediation, energy conversion and storage application as a novel, robust, multidimensional and more proficient materials.

Recent advancement in conjugated polymers based photocatalytic technology for air pollutants abatement: Cases of CO2, NOx, and VOCs

According to World Health Organization (WHO) survey, air pollution has become the major reason of several fatal diseases, which had led to the death of 7 million peoples around the globe. The 9 people out of 10 breathe air, which exceeds WHO recommendations. Several strategies are in practice to reduce the emission of pollutants into the air, and also strict industrial, scientific, and health recommendations to use sustainable green technologies to reduce the emission of contaminants into the air. Photocatalysis technology recently has been raised as a green technology to be in practice towards the removal of air pollutants. The scientific community has passed a long pathway to develop such technology from the material, and reactor points of view. Many classes of photoactive materials have been suggested to achieve such a target. In this context, the contribution of conjugated polymers (CPs), and their modification with some common inorganic semiconductors as novel photocatalysts, has never been addressed in literature till now for said application, and is critically evaluated in this review. As we know that CPs have unique characteristics compared to inorganic semiconductors, because of their conductivity, excellent light response, good sorption ability, better redox charge generation, and separation along with a delocalized π-electrons system. The advances in photocatalytic removal/reduction of three primary air-polluting compounds such as CO₂, NO_X, and VOCs using CPs based photocatalysts are discussed in detail. Furthermore, the synergetic effects, obtained in CPs after combining with inorganic semiconductors are also comprehensively summarized in this review. However, such a combined system, on to better charges generation and separation, may make the Adsorb & Shuttle process into action, wherein, CPs may play the sorbing area. And, we hope that, the critical discussion on the further enhancement of photoactivity and future recommendations will open the doors for up-to-date technology transfer in modern research.

New development and photocatalytic performance and antimicrobial activity of α-NH4(VO2)(HPO4) nanosheets

α-NH₄(VO₂)(HPO₄) nanosheets were developed by hydrothermal method. Furthermore, it's determined by the several analyses like XRD, Raman, FESEM, TEM, UV-Visible spectroscopy, TGA and DRS UV-Visible spectroscopy studies. The orthorhombic crystalline phase of α-NH₄(VO₂)(HPO₄) nanosheets were recognized by XRD analysis. The α-NH₄(VO₂)(HPO₄) nanosheets functional groups identification was investigated by Raman spectroscopy. Thermal gravimetric analysis of α-NH₄(VO₂)(HPO₄) nanosheets were identified and its attain for three decomposition stages. The nanosheets of the α-NH₄(VO₂)(HPO₄) was clearly evaluated by FESEM and TEM measurements. α-NH₄(VO₂)(HPO₄) nanomaterial band gap energy was determined by DRS UV Visible spectroscopy analysis and the calculated bandgap energy is 1.83 eV. Hence, it was more convenient way for the dye degradation applications. These α-NH₄(VO₂)(HPO₄) nanosheets was will be tested in the photocatalytic and antimicrobial applications. In this case, antimicrobial study was not encouraged in the catalyst. Consequently, this material has more encouraging for electrostatic interaction with enhanced for the applications.

Recent advances of bismuth titanate based photocatalysts engineering for enhanced organic contaminates oxidation in water: A review

Over more than three decades, the scientific community has been contentiously interested in structuring varying photocatalytic materials with unique properties for appropriate technology transfer. Most of the existing reported photocatalysts in the literature show pros and cons by considering the type of application and working conditions. Bismuth titanate oxides (BTO) are novel photocatalysts that raised recently towards energy and environmental-related applications. Most recent advances to developing bismuth titanate-based photocatalysts for the oxidation of organic pollutants in the water phase were reviewed in this report. To counter the potential drawbacks of BTO materials, i.e., rapid recombination of photoproduced charges, and further promote the photoactivity, most reported approaches were discussed, including creating direct Z-scheme junctions, conventional heterojunctions, metal/non-metal doping, coupling with carbon materials, surface modification and construction of oxygen vacancies. In the end, the review addresses the future trends for better engineering and application of BTO based photocatalysts towards the photodegradation of organic pollutants in water under controlled lab and large scales conditions.

Photodegradation under UV Light Irradiation of Various Types and Systems of Organic Pollutants in the Presence of a Performant BiPO4 Photocatalyst

In this study, we prepared spheroid microstructures of monoclinic bismuth phosphate BiPO4 by a facile solid-state reaction at 500 °C. The crystal structure was refined using the Rietveld method, where the crystal cell was resolved using a monoclinic system (parameters a, b, c, β) with space group P21/n. SEM images showed that the solid catalyst presented homogeneous morphologies. These BiPO4 microparticles (BiP-500) have been used as photocatalysts to photodegrade, under UV light irradiation, three cationic dyes (Rhodamine B, RhB; Methylene Blue, MB; and Toluidine Blue, TB), three anionic dyes (Congo Red, CR; Orange G, OG; and Methyl Orange, MO) and mixtures of RhB-MB, RhB-OG and MO-OG organic dyes. The photodegradation efficiency of these BiP-500 microparticles is found to be optimal in the case of RhB solutions, RhB-MB and RhB-OG binary mixtures. The BiP-500 catalyst shows a high selectivity for the conversion of the mixture of dyes into CO2 and H2O. Total organic carbon analysis of an anionic dye and a cationic dye (RhB, OG and RhB-MB) confirms the mineralization of the pollutants in the presence of BiP-500 particles. The photocatalytic efficiency of our BiP-500 photocatalyst has been confirmed, with a view to facilitate applications in the field of the depollution of wastewater in the agricultural environment by the degradation of parathion-methyl (PM) as a pollutant.

Z-scheme WO3/PANI heterojunctions with enhanced photocatalytic activity under visible light: A depth experimental and DFT studies

A WO₃@PANI heterojunction photocatalyst with a various mass ratio of polyaniline to WO₃ was obtained via the in situ oxidative deposition polymerization of aniline monomer in the presence of WO₃ powder. The characterization of WO₃@PANI composites was carried via X-ray diffraction (XRD), scanning electron microscopy (SEM-EDS), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), ultraviolet-visible diffuse reflection spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectroscopy (PL). The photocatalytic efficiency of WO₃@PANI photocatalysts was assessed by following the decomposition of the Rhodamine B (RhB) dye under visible light irradiation (λ >420 nm). The results evidenced the high efficiency of the WO₃@PANI (0.5 wt %) nanocomposite in the photocatalytic degradation of RhB (90% within 120 min) under visible light irradiation 3.6 times compared to pure WO₃. The synergistic effect between PANI and WO₃ is the reason for the increased photogenerated carrier separation. The superior photocatalytic performance of the WO₃@PANI catalyst was ascribed to the increased visible light in the visible range and the efficient charge carrier separation. Furthermore, the Density Functional Theory study (DFT) of WO₃@PANI was performed at the molecular level, to find its internal nature for the tuning of photocatalytic efficiency. The DFT results indicated that the chemical bonds connected the solid-solid contact interfaces between WO₃ and PANI. Finally, a plausible photocatalytic mechanism of WO₃@PANI (0.5 wt %) performance under visible light illumination is suggested to guide additional photocatalytic activity development.

Effect of heat treatment on the photocatalytic activity of α-Fe2O3 nanoparticles: towards diclofenac elimination

α-Fe₂O₃ nanoparticles were synthesized via a straightforward method. XRD, FTIR, SEM, ESR, and DRS techniques investigated the influence of various calcination temperatures on the crystal structure, optical, and photocatalytic properties of the samples. The obtained results demonstrated that the average crystallite size increased with the increase in the calcination temperature. Measured and computed optical properties were in accordance and the bandgap energy decreased with the increase in the calcination temperature. The highest photocatalytic degradation efficiency for diclofenac (DCF) was obtained with the sample calcinated at 300 °C (96%). The photocatalytic process occurs because of the presence of OH• radicals. The addition of H₂O₂ led to the inhibition of OH• radicals that H₂O₂ scavenged.

Facile fabrication of novel Fe3O4-SnO2-gC3N4 ternary nanocomposites and their photocatalytic properties towards the degradation of carbofuran

Herein, Fe₃O₄-SnO₂ nanoheterojunction has been synthesized and successfully encapsulated in gC₃N₄ matrix using a novel hydrothermal technique. The synthesized material was characterized using sophisticated analytical methods like XRD, TEM, BET, UV-Vis, VSM and XPS to evaluate structural, morphological, optical, magnetic and surface chemical properties. The hybrid nanostructure Fe₃O₄-SnO₂-gC₃N₄ has been utilized for the LED light-induced photocatalytic degradation of carbofuran. The catalyst exhibited notable photocatalytic performance under visible light with an efficiency of ~89% and pseudo first order rate constant of 0.015 min^-1. The result of change in variables like catalyst dose, pollutant concentration, pH and contact time on the photodegradation efficiency and degradation kinetics was studied. The incorporation of Fe₃O₄ improved the magnetic separation of the catalyst after several cycles of operation, thereby improving the practical utility of the catalyst system to tackle organic pollutants.

Synthesis and characterization of arginine-doped heliotrope leaves with high clean-up capacity for crystal violet dye from aqueous media

A novel arginine-modified Heliotrope leaf (Arg@HL) was used as adsorbent for the crystal violet (CV) dye adsorption in a batch process. The physicochemical and morphological composition of Arg@HL were characterized by field-emission scanning electron microscopy (FE-SEM), Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The experiments were carried out to investigate the factors that influence the dye uptake by the adsorbent, such as the contact time under agitation, adsorbent amount, initial dye concentration, temperature and pH of dye solution. The optimum conditions of adsorption were found on the batch scale as followed: CV concentration of 20 mg·L^-1, an amount of 0.75 g·L^-1 of the adsorbent, 90 min contact time, 6 pH and 25 °C temperature for Arg@HL. The results confirmed a second-order model explaining the dye crystal violet's adsorption's kinetics by Arg-Heliotrope leaves. The Langmuir model effectively defines the adsorption isotherms. The results revealed that the Arg@HL has the potential to be used as a low-cost adsorbent for the removal of CV dye from aqueous solutions.

Rapid magnetic enrichment and sensitive detection of Sudan pollutants with nanoscale zero valent iron-based nanomaterials in combination with liquid chromatography-ultraviolet detector

In present work, we reported a new nanomaterial nano Fe⁰ decorated with SiO₂ and dopamine by self-assembly method (Fe@SiO₂@PDA). A sensitive method for determination of Sudan pollutants in aqueous samples was developed using Fe@SiO₂@PDA as magnetic solid phase extraction adsorbents prior to high-performance liquid chromatography with variable wavelength detector. The possible parameters which would affect the enrichment have been optimized. The best parameters were as follows: elutent, 4.5 mL methanol; adsorbent dosage, 30 mg; adsorption time, 20 min; elution time, 18 min; sample pH 7; sample volume, 40 mL. The experimental results demonstrated that Fe@SiO₂@PDA exhibited good adsorption properties to Sudan Red dyes. The established method provided excellent linear ranges over 0.01-50 μg L^-1 and detection limits ranged from 2.0 to 5.1 ng L^-1 for Sudan red I-IV. The developed method was also evaluated with real water samples and the results demonstrated that it was of applicative value owing to its merits including robustness, easy operation, fastness, cheapness and high enrichment efficiency, and had great prospect in environmental fields.

Polyaniline coated tungsten trioxide as an effective adsorbent for the removal of orange G dye from aqueous media

In this work, the core–shell PANI@WO₃ composite was obtained from the reaction of aniline monomer polymerization with WO₃ particles; sodium persulfate was used as an oxidant. Various analytical techniques such as scanning electron microscopy (SEM-EDS), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Brunauer–Emmett–Teller (BET), and X-ray photoelectron spectroscopy (XPS) were used to characterize the as-prepared PANI@WO₃ adsorbent, which well confirmed that the WO₃ particles were coated by polyaniline polymer. The PANI@WO₃ composite was tested as an adsorbent to remove reactive orange G (OG) for the first time. pH, adsorbent dose, contact time, initial dye concentration, and temperature were systematically investigated in order to study their effect on the adsorption process. The experimental findings showed that the PANI@WO₃ composite has considerable potential to remove an aqueous OG dye. Langmuir and Freundlich's models were used to analyze the equilibrium isotherms of OG dye adsorption on the PANI@WO₃ composite. As a result, the best correlation of the experimental data was provided by the Langmuir model, and the maximum capacity of adsorption was 226.50 mg g⁻¹. From a thermodynamic point of view, the OG dye adsorption process occurred spontaneously and endothermically. Importantly, PANI@WO₃ still exhibited an excellent adsorption capability after four regeneration cycles, indicating the potential reusability of the PANI@WO₃ composite. These results indicate that the as prepared PANI@WO₃ composite could be employed as an efficient adsorbent and was much better than the parent material adsorption of OG dye.

In this work, the core–shell PANI@WO₃ composite was obtained from the reaction of aniline monomer polymerization with WO₃ particles; sodium persulfate was used as an oxidant.

Effects of biodiesels on the physicochemical properties and oxidative reactivity of diesel particulates: A review

Particulate emissions from the combustion of diesel have always been the main concern, especially in recent years, with continuously stringent particulate emission regulation for diesel engines. To alleviate the problem, biodiesel has been received great attention because of its being environment-friendly, widely available and renewable. The application of biodiesel in diesel engines changes the combustion process, thus varies physicochemical property of the particulate matter (PM) formed, which in turn influences the oxidative reactivity of soot particles. In view of this, it is particularly important to analyze soot particles from the diesel engine fueled with biodiesels. This review focus on the effects of biodiesels on the physicochemical properties of soot particles, such as surface morphology, nanostructure, active surface area, element composition, elemental and organic carbon contents, surface functional groups, sp² and sp³ hybridizations, etc. The impact of engine operating conditions (i.e. engine load, engine speed, fuel injection timing, fuel injection pressure, exhaust gas recirculation, etc.) on characteristics of soot particles from diesel engines powered by biodiesel is also discussed. Whereafter, the relationships between soot physicochemical characteristics and soot oxidative reactivity are reviewed. Finally, the main conclusions are outlined as well as the proposed research work in the future.

Phase Transformation, Photocatalytic and Photoluminescent Properties of BiPO4 Catalysts Prepared by Solid-State Reaction: Degradation of Rhodamine B

Polycrystalline bismuth phosphate BiPO4 was synthesized by solid-state reaction at different temperatures varying from 500 to 900 °C. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDS) and Raman spectroscopy. The low-temperature phase of BiPO4 has monoclinic structure with a space group P21/n, and was transformed into the monoclinic phase P21/m with a slight distortion of monoclinic lattice when it was heated above 500 °C. The effect of the transformation on the structure, morphology and photocatalytic properties was examined. The photocatalytic activity of each sample, in presence of Rhodamine B (RhB) in aqueous solution, was carried out and analyzed under UV light irradiation. Photoexperiments showed that the material prepared at 500 °C is the best catalyst with degradation efficiency of the order of 96% after 12 min of reaction time under UV light irradiation. This high photocatalytic efficiency could be due to their structural and morphological changes. The photocatalytic degradation mechanism of RhB in the presence of the best photocatalyst BiP-500 °C is proposed. The stability of the catalyst was also examined by carrying out four successive tests of the degradation in the presence of BiP-500 °C. Total organic carbon (TOC) was used to further estimate the rate of mineralization in the presence of BiP-500 °C (83% TOC removal). Photoluminescence experiments performed under UV-laser light irradiation revealed emissions in the green-orange range, with optimal intensities for the mix systems observed at 550 °C.

Novel Z-Scheme/Type-II CdS@ZnO/g-C3N4 ternary nanocomposites for the durable photodegradation of organics: Kinetic and mechanistic insights

Visible-light-driven photocatalysis is a green and efficient strategy for wastewater treatment, where graphitic carbon nitride-based semiconductors showed excellent performance in this regard. Consequently, we report on the development of a green and facile one-pot room-temperature ultrasonic route for the preparation of novel ternary nanocomposite of cadmium sulfide quantum dots (CdS QDs), zinc oxide nanoparticles (ZnO NPs), and graphitic carbon nitride nanosheets (g-C₃N₄ NSs). The proposed materials had been characterized by several physicochemical techniques such as PXRD, XPS, FE-SEM, HR-TEM, PL, and DRS. The photocatalytic efficiency of the proposed photocatalysts was assessed towards the photodegradation of Rhodamine B dye as a water pollutant model using spectrophotometric measurements. The as-synthesized novel ternary nanocomposite (CdS@ZnO/g-C₃N₄) exhibited perfect photocatalytic activity, where almost complete degradation was achieved in only 2 h under UV-irradiation or 3 h under visible-irradiation. Various methods were used to elucidate the kinetics of the photocatalytic process. Moreover, CdS@ZnO/g-C₃N₄ exhibited a unique synergetic performance when compared to the corresponding binary composites or the individual components. This synergetic performance could be ascribed to the perfect electronic band configuration of the three components, leading to the establishment of several combined synergetic Z-Scheme/Type-II photocatalytic heterojunctions, which is the proposed mechanism for the observed synergetic photocatalytic reactivity of the as-synthesized CdS@ZnO/g-C₃N₄ nanocomposite when compared to the single and binary nanocomposite counterparts. Furthermore, the effects of both the type and concentration of various scavengers on the photocatalytic activity were assessed to investigate the most reactive species, where the reductive degradation pathway was found to be the predominant route. Finally, the photocatalytic efficiency of the as-synthesized CdS@ZnO/g-C₃N₄ composite showed promising and competing results when compared to other photocatalysts reported in the literature.

Green and High Effective Scale Inhibitor Based on Ring-Opening Graft Modification of Polyaspartic Acid

Polyaspartic acid (PASP)-based green scale inhibitor has great potential application in water treatment. Here, we first synthesized PASP in ionic liquid. Then, an effective PASP-based green scale inhibitor was synthesized by ring-opening graft modification of PASP with both aspartic acid (ASP) and monoethanolamine (MEA). Its chemical composition was characterized by gel chromatography (GPC), Fourier transform infrared spectroscopy (FTIR), and 1H nuclear magnetic resonance (1H NMR). Scale inhibition efficiency was measured by static scale inhibition tests. The results showed that the new PASP-based scale inhibitor has high scale inhibition to both CaCO3 and Ca3(PO4)2. When the concentration was increased to 2 mg/L, the inhibition efficiency of the new PASP-based scale inhibitor was 99% for CaCO3, while when the concentration was raised to only 4 mg/L, its inhibition efficiency increased to 100% for Ca3(PO4)2. Scanning electronic microscopy (SEM) and X-ray diffraction (XRD) were used to analyze the changes of crystal structure for CaCO3 and Ca3(PO4)2 after adding the new PASP-based scale inhibitor. The crystal size of CaCO3 and Ca3(PO4)2 became smaller and the crystal form became amorphous after adding the modified PASPs compared with adding pure PASP. Moreover, the modified PASP showed good biodegradation performance.

The molecular mechanisms of Chlorella sp. responding to high CO2: A study based on comparative transcriptome analysis between strains with high- and low-CO2 tolerance

High CO₂ acclimation for microalgae has attracted large research attention owing to the usefulness of microalgae in bio-sequestration of CO₂ from the emission source. In this study, one high CO₂ tolerant (LAMB 31) and non-tolerant (LAMB 122) Chlorella sp. strains were transferred from air to 40% CO₂, during which four time points were chosen for comparative transcriptome analysis. Gene changes started in the lag phase (T1) of population growth with more genes (7889) upregulated in LAMB 31 than in LAMB 122 (1092). Further function enrichments indicated: In LAMB 31, up-regulation of genes in cyclic electron transportation, F-type ATPase and Calvin cycle were associated with the enhancement of carbon fixation abilities; upregulation of genes in phosphorylation together with V-ATPase, which contributed to cytoplasmatic pH stability; Lastly, enhancement of carbon metabolisms including TCA cycle and glycolysis accelerated the consumption of cellular organic carbon. Most of the genes in these pathways and processes showed downregulation in LAMB 122. This study disclosed the most complete transcriptional molecular mechanisms of Chlorella sp. responding to high CO₂ by combining CO₂ fixation, transportation, and metabolic processes. The results provided valuable genetic information for future screening and breeding of microalgae with high-CO₂ tolerance for more efficient CO₂ bio-sequestration.

Defect enrich ultrathin TiO2 nanosheets for rapid adsorption and visible light mediated PPCPs degradation

Recently, PPCPs have attracted extensive attention as emerging pollutants. Due to the strong hydrophilicity and small molecular weight, PPCPs are difficult to be fully removed by adsorption and other processes, posing a serious threat to the ecological environment. Here, we demonstrate solvothermal synthesis of defect enrich TiO₂ nanosheets through simple copper doping. Novel TiO₂ nanosheets were found to be mesoporous with high specific surface area and exhibited excellent visible light response. Performance of the developed TiO₂ nanosheets were evaluated towards photocatalytic degradation of two model pollutants, tetracycline and acetaminophen. Results showed robust degradation of tetracycline and acetaminophen under visible-light irradiation within 100 min. Meanwhile, the potential relationship between the structural characteristics and excellent ability of the catalyst was discussed, as well as probable mechanism. Additionally, a study on the toxicity of tetracycline solution to human skin epidermal cells showed that the toxicity of the treated solution to cells is greatly reduced. The prepared catalysts show good repeatability (a slightly decrease ca.3% after 5 cycles) and applicability, providing a reasonable design for water remediation.

Treatment of wastewater from a dairy plant by adsorption using synthesized copper oxide nanoparticles: kinetics and isotherms modeling optimization

Dairy plants produce 1 to 4 L of wastewater per 1 L of processed milk. The wastewater contains high values of chemical oxygen demand (COD) and biochemical oxygen demand (BOD) concentrations, in addition to high levels of dissolved solids. In this study, synthesized copper oxide nanoparticles (CuONPs) coupled with Sophora Japonica fruit, were used as an adsorbent, for the first time, to treat the effluent of dairy plants in a batch adsorption process. The analysis techniques, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM) were utilized to characterize the adsorbent. The COD removal, using (CuONPs)-based adsorbent, was investigated by varying contact time, masses of the adsorbent, initial COD value and temperatures. The optimum conditions for highest removal percentage were contact time of 120 min, a temperature of 25 °C, pH value of 7.5, and 1 g of adsorbent. The initial COD values used were in the range of 100-700 ppm. The COD percent removal was in the range of 77 to 95%. Freundlich isotherm exhibited the best fitting for the results (R² = 0.998) with a favorable spontaneous exothermic adsorption process. Based on the calculated normalized deviation value, the modified diffusion model, intra-diffusion, and pseudo-second-order kinetics all showed very good fitting for the adsorption data as indicated by the kinetics study.

Facile synthesis and characterization of a novel 1,2,4,5-benzene tetracarboxylic acid doped polyaniline@zinc phosphate nanocomposite for highly efficient removal of hazardous hexavalent chromium ions from water

The present study describes the preparation of a novel 1,2,4,5-benzene tetracarboxylic acid doped polyaniline@zinc phosphate (BTCA-PANI@ZnP) nanocomposite via a facile two-step procedure. Thereafter, the as-prepared composite material adsorption characteristics for Cr(VI) ions removal were evaluated under batch adsorption. Kinetic approach studies for Cr(VI) removal, clearly demonstrated that the results of the adsorption process followed the pseudo second order and Langmuir models. The thermodynamic study indicated a spontaneous and endothermic process. Furthermore, higher monolayer adsorption was determined to be 933.88 mg g^-1. In addition, the capability study regarding Cr(VI) ions adsorption over BTCA-PANI@ZnP nanocomposite clearly revealed that our method is suitable for large scale application. X-ray photoelectron spectroscopy (XPS) analysis confirmed Cr(VI) adsorption on the BTCA-PANI@ZnP surface, followed by its subsequent reduction to Cr(III). Thus, the occurrence of external mass transfer, electrostatic attraction and reduction phenomenon were considered as main mechanistic pathways of Cr(VI) ions removal. The superior adsorption performance of the material, the multi-dimensional characteristics of the surface and the involvement of multiple removal mechanisms clearly demonstrated the potential applicability of the BTCA-PANI@ZnP material as an effective alternative for the removal of Cr(VI) ions from wastewater.

Recent progress on the enhancement of photocatalytic properties of BiPO4 using π-conjugated materials

Semiconductor photocatalysis is regarded as most privileged solution for energy conversion and environmental application. Recently, photocatalysis methods using bismuth-based photocatalysts, such as BiPO₄, have been extensively investigated owing to their superior efficacy regarding organic pollutant degradation and their further mineralization into CO₂ and H₂O. It is well known that BiPO₄ monoclinic phase exhibited better photocatalytic performance compared to Degussa (Evonik) P25 TiO₂ in term of ultraviolet light driven organic pollutants degradation. However, its wide band gap, poor adsorptive performance and large size make BiPO₄ less active under visible light irradiation. However, extensive research works have been conducted in the past with the aim of improving visible light driven BiPO₄ activity by constructing a series of heterostructures, mainly coupled with π-conjugated architecture (e.g., conductive polymer, dye sensitization and carbonaceous materials). However, a critical review of modified BiPO₄ systems using π-conjugated materials has not been published to date. Therefore, this current review article was designed with the aim of presenting a brief current state-of-the-art towards synthesis methods of BiPO₄ in the first section, with an especial focuses onto its crystal-microstructure, optical and photocatalytic properties. Moreover, the most relevant strategies that have been employed to improve its photocatalytic activities are then addressed as the main part of this review. Finally, the last section presents ongoing challenges and perspectives for modified BiPO₄ systems using π-conjugated materials.