Whole meal and white flour from Argentine wheat genotypes: Mineral and arabinoxylan differences

Predominant factors in milling and wheat variety influencing particle size and quality of whole wheat flour

This study investigated the effects of mill type, milling conditions, and wheat variety on the mean particle size, particle size distribution, and quality characteristics of whole wheat flour (WWFs). Three wheat varieties (Goso [GS], Hojoong [HJ], and Joongmo [JM]), representing varying protein contents, were milled using two types of mills: an ultra-centrifugal mill (UM) and a cutting mill (CM). The milling conditions were adjusted based on the sieve openings (0.5 and 1.0 mm) and rotor speeds (UM: 6000 and 14,000 rpm; CM: 2000 and 4000 rpm). The mean particle size and particle size distribution of the WWFs were significantly influenced by the mill type, milling conditions, and their interactions. UM and CM produced distinct particle size distributions, with CM yielding a broader range and a more pronounced bimodal distribution. Furthermore, the type of mill and milling conditions, along with their interactions, affected the damaged starch content, water and sodium carbonate solvent retention capacity, pasting properties, and antioxidant activity of the WWFs. The wheat variety influenced parameters such as moisture, ash, damaged starch content, sodium dodecyl sulfate sedimentation volume, rapid viscoanalyzer (RVA) pasting properties, total phenolic content, and antioxidant activity. Notably, selecting an appropriate mill type and milling conditions is critical for producing WWFs with high gluten strength from high-protein wheat varieties. PRACTICAL APPLICATION: Controlling particle size through milling optimization is essential for producing high-quality whole wheat flour, particularly from wheat varieties with high protein content.

Improving wheat grain composition for human health by constructing a QTL atlas for essential minerals

Wheat is an important source of minerals for human nutrition and increasing grain mineral content can contribute to reducing mineral deficiencies. Here, we identify QTLs for mineral micronutrients in grain of wheat by determining the contents of six minerals in a total of eleven sample sets of three biparental populations from crosses between A.E. Watkins landraces and cv. Paragon. Twenty-three of the QTLs are mapped in two or more sample sets, with LOD scores above five in at least one set with the increasing alleles for sixteen of the QTLs being present in the landraces and seven in Paragon. Of these QTLs, the number for each mineral varies between three and five and they are located on 14 of the 21 chromosomes, with clusters on chromosomes 5A (four), 6A (three), and 7A (three). The gene content within 5 megabases of DNA on either side of the marker for the QTL with the highest LOD score is determined and the gene responsible for the strongest QTL (chromosome 5A for Ca) identified as an ATPase transporter gene (TraesCS5A02G543300) using mutagenesis. The identification of these QTLs, together with associated SNP markers and candidate genes, will facilitate the improvement of grain nutritional quality.

Efficient arabinoxylan assay for wheat: Exploring variability and molecular marker associations in Wholemeal and refined flour

In this study, we present a modified high throughput phloroglucinol colorimetric assay for the quantification of arabinoxylans (AX) in wheat named PentoQuant. The method was downscaled from a 10 ml glass tube to 2 ml microcentrifuge tube format, resulting in a fivefold increase in throughput while concurrently reducing the overall cost and manual labor required for the analysis. Comparison with established colorimetric assays and gas chromatography validates the modified protocol, demonstrating its superior repeatability, rapidity, and simplicity. The effectiveness of the protocol was tested on 606 unique whole meal (WM) and refined flour (RF) bread wheat samples which revealed the presence of more than a twofold variation in both the soluble (WE-AX) and total (TOT-AX) AX fractions in WM (TOT-AX = 31.9-76.1 mg/g; WE-AX = 4.4-12.6 mg/g) and RF (TOT-AX = 7.7-22.4 mg/g; WE-AX = 3.9-11.4 mg/g). Results obtained from the AX quantification were used to test the effectiveness of four molecular markers associated with AX variation and targeting two major genomic regions on the 1BL and 6BS chromosomes. These markers appeared to be particularly relevant for the WE-AX fraction, providing insights to enable marker-assisted breeding.

Exploiting Rye in Wheat Quality Breeding: The Case of Arabinoxylan Content

Rye (Secale cereale subsp. cereale L.) has long been exploited as a valuable alternative genetic resource in wheat (Triticum aestivum L.) breeding. Indeed, the introgression of rye genetic material led to significant breakthroughs in the improvement of disease and pest resistance of wheat, as well as a few agronomic traits. While such traits remain a high priority in cereal breeding, nutritional aspects of grain crops are coming under the spotlight as consumers become more conscious about their dietary choices and the food industry strives to offer food options that meet their demands. To address this new challenge, wheat breeding can once again turn to rye to look for additional genetic variation. A nutritional aspect that can potentially greatly benefit from the introgression of rye genetic material is the dietary fibre content of flour. In fact, rye is richer in dietary fibre than wheat, especially in terms of arabinoxylan content. Arabinoxylan is a major dietary fibre component in wheat and rye endosperm flours, and it is associated with a variety of health benefits, including normalisation of glycaemic levels and promotion of the gut microbiota. Thus, it is a valuable addition to the human diet, and it can represent a novel target for wheat-rye introgression breeding.

Genome-Wide Association Study of Arabinoxylan Content from a 562 Hexaploid Wheat Collection

The selection of wheat varieties with high arabinoxylan (AX) levels could effectively improve the daily consumption of dietary fiber. However, studies on the selection of markers for AX levels are scarce. This study analyzed AX levels in 562 wheat genotypes collected from 46 countries using a GWAS with the BLINK model in the GAPIT3. Wheat genotypes were classified into eight subpopulations that exhibited high genetic differentiation based on 31,926 SNP loci. Eight candidate genes were identified, among which those encoding F-box domain-containing proteins, disease resistance protein RPM1, and bZIP transcription factor 29 highly correlated with AX levels. The AX level was higher in the adenine allele than in the guanine alleles of these genes in the wheat collection. In addition, the AX level was approximately 10% higher in 3 adenine combinations than 2 guanine, 1 adenine, and 3 guanine combinations in genotypes of three genes (F-box domain-containing proteins, RPM1, and bZIP transcription factor 29). The adenine allele, present in 97.46% of AX-95086356 SNP, exhibited a high correlation with AX levels following classification by country. Notably, the East Asian wheat genotypes contain high adenine alleles in three genes. These results highlight the potential of these three SNPs to serve as selectable markers for high AX content.

Addition of Amaranth Flour of Different Particle Sizes at Established Doses in Wheat Flour to Achieve a Nutritional Improved Wheat Bread

Amaranth is an underutilized pseudocereal that can be used to supplement wheat flour (WF) in order to improve the nutritional quality of bread. Bread digestibility is impacted by particle size which produces different nutritional properties. This research aims to evaluate the baking characteristics of optimal wheat−amaranth composite flour for each studied amaranth flour (AF) particle size at doses previously established based on an optimization process and to characterize from a physical, textural, nutritional, and sensorial point of view the obtained bread. The results revealed that the optimal wheat−amaranth composite flour with medium and small particle size, respectively showed a slightly lower α-amylase activity, while dough development time was significantly higher compared to the WF. A significant (p < 0.05) decrease was observed in the elasticity, deformation energy, and dynamic rheological parameters of the optimal composite dough for all the particle sizes, whereas fermentation parameters showed higher values compared to the control, indicating the ability of the gluten structure in large, medium, and small particle sizes of AF to hold the gas and to expand without collapsing. The physical, textural, and especially nutritional characteristics of the optimal WF-AF bread were enhanced. The sensory evaluation results revealed high scores (8.70) for the acceptability of optimal bread with a medium particle size as compared to wheat bread (8.25). The protein and ash content of the optimal breads with large, medium, and small AF particle sizes, respectively, increased significantly, from 8.92 to 10.58%, and 0.82 to 0.99%, respectively, relative to the wheat flour bread (8.35% and 0.72%, respectively). The mineral content was up to two times higher in the optimal breads compared to wheat flour bread. The findings generated from this study are helpful in bakery industry for designing products with enhanced nutritional properties and for introducing new products to the market.

Element Content in Different Wheat Flours and Bread Varieties

The most consumed cereal-based product worldwide is bread. “Caaveiro”, an autochthonous variety with a recent growing interest, is one of the wheat varieties that fulfill the 25% local flour requirement in the PGI “Pan Galego” bread baking industry. The element content of the refined wheat flours used to make “Pan Galego” (‘‘Caaveiro’’, FCv; Castilla, FC; and a mixture of both, FM) was evaluated in ICP-MS. In addition, wholegrain flour (FWM) was included in the analysis. Loaves of bread were made with these flours (a, 100% FC; b, 100% FCv); and c, FM: 75% FC + 25% FCv) and their element content was analyzed. Wholegrain flour ranked the highest in almost all elements, highlighting the P (494.80 mg/100 g), while the FM and the FC presented the opposite behavior, with the highest Se values (14.4 and 15.8 mg/100 g, respectively). FCv was situated in an intermediate position regarding P, K, Mg, Mn, Zn, Fe and Na content, standing closer to FWM, although it presents the highest values for Cu (1076.3 µg/100 g). The differences observed in flour were maintained in bread. Hence, the local cultivar ‘‘Caaveiro’’ has an interesting nutritional profile from the point of view of the element content.

Investigation of Quinoa Seeds Fractions and Their Application in Wheat Bread Production

The present study aimed to investigate the influence of quinoa fractions (QF) on the chemical components of wheat flour (WF), dough rheological properties, and baking performance of wheat bread. The microstructure and molecular conformations of QF fractions were dependent to the particle size. The protein, lipids, and ash contents of composite flours increased with the increase of QF addition level, while particle size (PS) decreased these parameters as follows: Medium ˃ Small ˃ Large, the values being higher compared with the control (WF). QF addition raised dough tenacity from 86.33 to 117.00 mm H₂O, except for the small fraction, and decreased the extensibility from 94.00 to 26.00 mm, while PS determined an irregular trend. The highest QF addition levels and PS led to the highest dough viscoelastic moduli (55,420 Pa for QL_20, 65245 Pa for QM_20 and 48305 Pa for QS_20, respectively). Gradual increase of QF determined dough hardness increase and adhesiveness decrease. Bread firmness, springiness, and gumminess rises were proportional to the addition level. The volume, elasticity, and porosity of bread decreased with QF addition. Flour and bread crust and crumb color parameters were also influenced by QF addition with different PS.

Physicochemical, Mineral and Sensory Characteristics of Instant Citrullus lanatus mucosospermus (Egusi) Soup

Defatted egusi flour offers a food option high in protein and essential micronutrients. An instant processing method was adopted in a ready-to-eat instant soup using egusi grit, hydrocolloid, and defatted flour. A D-optimal quadratic mixture model was used to study the effect of the independent variables (grit, flour, and hydrocolloid) qualities. The quadratic model was adequate to navigate the design space for taste and appearance. The numerical optimization for appearance and taste of instant soup (IES) was used to obtain the optimal soup mix of 10 g of hydrocolloid, 57.2 of defatted flour and 17 g of grits. Sixteen trace and five major mineral elements were found in the egusi soup, with a high concentration of phosphorus (1220.4, 1326.2 and 1277.9 mg/100 g), potassium (1220.4, 1326.2 and 1277.9 mg/100 g), magnesium (822.2, 905.3 and 863.70 mg/100 g), calcium (172.3, 190.9 and 183.4 mg/100 g) and iron (53.7, 57.5 and 29.5 mg/100 g), and for instant egusi soups from boiled egusi grit (IESBG), instant egusi grit from spherified grit (IESSG) and instant egusi grit from extruded grit (IESEG), respectively. The amino acid profile of instant egusi soup offers all essential amino acids necessary to nourish the body. Phosphorus content was significantly (p ≤ 0.05) high across the three soups: 1742, 1836 and 1838 mg/100 g for IESBG, IESSG, and IESEG, respectively; IESSG and IESEG were significantly (p ≤ 0.05) higher in minerals when compared with IESBG. Instant egusi soup differed significantly (p ≤ 0.05) in lightness (L*), while the redness (a*) and yellowness (b*) did not vary significantly.

The Influence of the Addition of Nuts on the Thermal and Rheological Properties of Wheat Flour

The aim of the study was to assess the influence of replacing wheat flour with hazelnuts or walnuts, in various amounts, on the thermal and rheological properties of the obtained systems. The research material were systems in which wheat flour was replaced with ground hazelnuts (H) or walnuts (W) in the amount of 5%, 10%, and 15%. The parameters of the thermodynamic gelatinization characteristics were determined by the differential scanning calorimetry method. In addition, the pasting characteristics were determined with the use of a viscosity analyzer and the viscoelastic properties were assessed. Sweep frequency and creep and recovery tests were used to assess the viscoelastic properties of the tested gels. It was found that replacing wheat flour with nuts increased the values of gelatinization temperature, gelatinization, and retrogradation enthalpy, and the degree of retrogradation. The highest viscosity was characteristic of the control sample (2039 mPa·s), and the lowest for the paste with 15% addition of walnuts (1120 mPa·s). Replacing the flour with nuts resulted in a very visible reduction in the viscosity of such systems. In addition, gels based on the systems with the addition of H and W were weak gels (tan δ = G″/G' > 0.1), and the values of G' and G″ parameters decreased with the increased share of nuts in the systems. Creep and recovery analysis indicated that the systems in which wheat flour was replaced with hazelnuts were less susceptible to deformation compared to the systems with the addition of W.

Whole-flours from hard and soft wheat genotypes: study of the ability of prediction test to estimate whole flour end-use

The aims of this work were to assess the influence of the physicochemical composition of whole flour from soft and hard wheat genotypes on cookie and bread properties, as well as the ability of the prediction tests to estimate the whole meal flour end-use. Flours from hard and soft wheat genotypes proved to have different chemical composition and particle size distribution. Flours from hard wheat had lower particle average size and dietary fiber content, and higher lipid and wet gluten contents than flours from soft wheat. Particle size distribution, water absorption capacity and chemical composition of whole flours strongly influenced bread and cookie making performance. Considering prediction tests, flours from different wheat types were successfully discriminated using SDS-SI, SRC lac, and GI. However, rather weak correlations were found between the prediction test and the cookie and bread quality parameters. The prediction test, standardized for refined flours, showed a poor performance when whole flours were used. Nevertheless, grain texture and whole flour physicochemical properties did affect bread and cookie quality parameters, thus classical prediction tests should be modified in order to estimate the end-use performance of whole flours. Moreover, a standardization of the milling process should be considered.

Lead smelting alters wheat flour heavy metal concentrations and health risks

Wheat (Triticum aestivum L.) flour consumption may be a major source of human metal intake, especially when wheat is cultivated in metal-contaminated soils. This work investigated Cd, Cu, Pb, and Zn distribution in whole wheat flour, wheat flour, and wheat bran when grown in an area polluted by Pb smelting. Wheat product heavy metal concentrations were analyzed, and the (non)carcinogenic risks were assessed. Mean Cd, Cu, Pb, and Zn concentrations in whole wheat flour were 0.38, 3.83, 0.48, and 29.3 mg kg^-1 , respectively; those in flour were only slightly reduced. The ratios between noncarcinogenic average daily dose of whole wheat flour and wheat flour consumption ranged from 1.06 to 3.76, with Pb having the greatest values compared with other metals. For children, the average hazard quotients (HQs) of whole wheat flour consumption of Cd, Cu, Pb, and Zn were 4.19, 1.06, 1.53, and 1.07; those for wheat flour consumption were 3.81, 0.68, 0.70, and 0.98, respectively. The HQs of adults were less than those of children. Overall results indicated that consumption of wheat products may lead to health concerns in the heavy metal contaminated area, yet when wheat flour rather than whole wheat flour is consumed, only the human health risk from Pb ingestion is reduced. Altering or removing human edible crops in the most contaminated areas should be considered.

Locally Adapted and Organically Grown Landrace and Ancient Spring Cereals-A Unique Source of Minerals in the Human Diet

Consumer interest in local and organic produce, sustainability along the production chain and food products contributing to health, are laying the foundation for local and organic-based diets using nutrient-dense food. Here, we evaluated 25 locally adapted landrace and ancient spring cereal genotypes per location over four locations and three years, for mineral content, nutritional yield and nutrient density. The results showed a large variation in minerals content and composition in the genotypes, but also over cultivation locations, cultivation years and for genotype groups. Highest minerals content was found in oats, while highest content of Zn and Fe was found in ancient wheats. The wheat Diamant brun, the wheat landrace Öland and naked barley showed high mineral values and high content of Zn and Fe when grown in Alnarp. Nutritional yield, of the cereals evaluated here, was high related to values reported internationally but lower than those found in a comparable winter wheat material. The nutrient density was generally high; less than 350 g was needed if any of the evaluated genotype groups were to be used in the daily diet to reach the recommended value of Zn and Fe, while if the suggested Novel Nordic Diet mix was used, only 250 g were needed. A transfer from currently consumed cereals to those in the present study, along the New Nordic Diet path, showed their potential to contribute as sustainable and nutrient-rich sources in the human diet.

Genetic and Environmental Variation in Starch Content, Starch Granule Distribution and Starch Polymer Molecular Characteristics of French Bread Wheat

This study investigates genetic and environmental variation in starch content and characteristics of 14 French bread cultivars. Understanding the impact of these factors on wheat quality is important for processors and especially bakers to maintain and meet the requirements of industrial specifications. Different traits were evaluated: starch content, distribution of starch granules, percentage of amylose and amylopectin and their molecular characteristics (weight-average molar mass, number-average molar mass, polydispersity and gyration radius). Genetic, environment and their interaction had significant effects on all parameters. The relative magnitude of variance attributed to growth conditions, for most traits, was substantially higher (21% to 95%) than that attributed to either genotype (2% to 73%) or G × E interaction (2% to 17%). The largest environmental contribution (95%) to total variance was found for starch dispersity. The highest genetic influence was found for the percentage of A-type starch granules. G × E interaction had relatively little influence (≈7%) on total phenotypic variance. All molecular characteristics were much more influenced by environment than the respective percentages of amylose and amylopectin were. This huge difference in variance between factors obviously revealed the importance of the effect of growing conditions on characteristics of cultivars.

Potential Health Claims of Durum and Bread Wheat Flours as Functional Ingredients

Wheat is an important cereal with a key role in human nutrition. In this study, dietary fiber (DF) and arabinoxylans of different durum (Triticum turgidum ssp. Durum L.) and bread (Triticum aestivum L.) wheat flours were analyzed in order to point out their potential nutritional and health claims allege according to the current European regulation (Regulation (EU) No 432/2012). Moreover, other bioactive compounds (phenolics and tocopherols) were quantified as a first approach to their phytochemical composition in the analyzed wheat varieties. DF was analyzed following AOAC enzymatic-gravimetric methods; arabinoxylans and total phenols were quantified by colorimetric methods; tocopherols were determined by HPLC; antioxidant activity was evaluated using three different in vitro assays. Insoluble DF was the prevailing fraction in all analyzed samples. Water extractable arabinoxylans were higher in durum wheat flours. Whole flours contained higher total phenolics compounds. Alpha-tocopherol was the major isoform. Whole flours showed higher antioxidant properties. According to the obtained results, it is possible to allege all approved health claims referred to wheat, since all analyzed samples, especially whole flour and bran fraction, showed potential health benefits, as functional ingredients or functional foods, related with their phytochemical composition.

Dietary fiber sources and human benefits: The case study of cereal and pseudocereals

Dietary fiber (DF) includes the remnants of the edible part of plants and analogous carbohydrates that are resistant to digestion and absorption in the human small intestine with complete or partial fermentation in the human large intestine. DF can be classified into two main groups according to its solubility, namely insoluble dietary fiber (IDF) that mainly consists on cell wall components, including cellulose, some hemicelluloses, lignin and resistant starch, and soluble dietary fiber (SDF) that consists of non-cellulosic polysaccharides as non-digestible oligosaccharides, arabinoxylans (AX), β-glucans, some hemicelluloses, pectins, gums, mucilages and inulin. The intake of DF is associated with health benefits. IDF can contribute to the normal function of the intestinal tract and it has an important role in the prevention of colonic diverticulosis and constipation. SDF is extensively fermented by gut microbiota and it is associated with carbohydrate and lipid metabolism, with important health benefits due to its hypocholesterolemic properties. Due to these nutritional and health properties, DF is widely used as functional ingredients in food industry, being whole grain cereals, pulses, fruits and vegetables the main sources of DF. Also some synthetic sources are employed, namely polydextrose, hydroxypropyl methylcellulose or cyclodextrins. The DF content of cereals varies depending on cultivars, their botanical components (pericarp, emdosperm and germ) and the processing conditions they have undergone (baking, extrusion, etc.). In cereal grains, AX are the predominant non-cellulose DF polysaccharides followed by cellulose and β-glucans, while in pseudocereals, pectins are quantitatively predominant.

Biofortification with Iron and Zinc Improves Nutritional and Nutraceutical Properties of Common Wheat Flour and Bread

The effect of field foliar Fe and Zn biofortification on concentration and potential bioavailability of Fe and Zn and health-promoting compounds was studied in wholemeal flour of two common wheat varieties (old vs modern). Moreover, the effect of milling and bread making was studied. Biofortification increased the concentration of Zn (+78%) and its bioavailability (+48%) in the flour of the old variety, whereas it was ineffective in increasing Fe concentration in both varieties. However, the old variety showed higher concentration (+41%) and bioavailability (+26%) of Fe than the modern one. As regard milling, wholemeal flour had higher Fe, Zn concentration and health-promoting compounds compared to white flour. Bread making slightly change Fe and Zn concentration but greatly increased their bioavailability (77 and 70%, respectively). All these results are of great support for developing a production chain of enriched functional bread having a protective role against chronic cardio-vascular diseases.