Montmorillonite-chitosan bionanocomposites as adsorbents of the herbicide clopyralid in aqueous solution and soil/water suspensions

Novel chitosan-based barrier materials for environmental containment: Synthesis, characterization, and contaminant removal capacities and mechanisms

This study critically appraises employing chitosan as a composite with bentonite, biochar, or both materials as an alternative to conventional barrier materials. A comprehensive literature review was conducted to identify the studies reporting chitosan-bentonite composite (CBC), chitosan amended biochar (CAB), and chitosan-bentonite-biochar composite (CBBC) for effective removal of various contaminants. The study aims to review the synthesis of these composites, identify fundamental properties affecting their adsorption capacities, and examine how these properties affect or enhance the removal abilities of other materials within the composite. Notably, CBC composites have the advantage of adsorbing both cationic and anionic species, such as heavy metals and dyes, due to the cationic nature of chitosan and the anionic nature of montmorillonite, along with the increased accessible surface area due to the clay. CAB composites have the unique advantage of being low-cost sorbents with high specific surface area, affinity for a wide range of contaminants owing to the high surface area and microporosity of biochar, and abundant available functional groups from the chitosan. Limited studies have reported the utilization of CBBC composites to remove various contaminants. These composites can be prepared by combining the steps employed in preparing CBC and CAB composites. They can benefit from the favorable adsorption properties of all three materials while also satisfying the mechanical requirements of a barrier material. This study serves as a knowledge base for future research to develop novel composite barrier materials by incorporating chitosan and biochar as amendments to bentonite.

Herbicidal weed management practices: History and future prospects of nanotechnology in an eco-friendly crop production system

Weed management is an important aspect of crop production, as weeds cause significant losses in terms of yield and quality. Various approaches to weed management are commonly practiced by crop growers. Due to limitations in other control methods, farmers often choose herbicides as a cost-effective, rapid and highly efficient weed control strategy. Although herbicides are highly effective on most weeds, they are not a complete solution for weed management because of the genetic diversity and evolving flexibility of weed communities. The excessive and indiscriminate use of herbicides and their dominance in weed control have triggered the rapid generation of herbicide-resistant weed species. Moreover, environmental losses of active ingredients in the herbicides cause serious damage to the environment and pose a serious threat to living organisms. Scientific advances have enabled nanotechnology to emerge as an innovation with real potential in modern agriculture, adding a new dimension in the preparation of controlled release formulations (CRF) of herbicides. Here the required amount of active ingredients is released over longer periods of time to obtain the desired biological efficacy whilst reducing the harmful effects of these chemicals. Various organic and inorganic carrier materials have been utilised in CRF and researchers have a wide range of options for the synthesis of eco-friendly carrier materials, especially those with less or no toxicity to living organisms. This manuscript addresses the history, progress, and consequences of herbicide application, and discusses potential ways to reduce eco-toxicity due to herbicide application, along with directions for future research areas using the benefits of nanotechnology.

Chitosan nanoplatforms in agriculture for multi-potential applications - Adsorption/removal, sustained release, sensing of pollutants & delivering their alternatives - A comprehensive review

An increase in the global population has led to an increment in the food consumption, which has demanded high food production. To meet the production demands, different techniques and technologies are adopted in agriculture the past 70 years, where utilization of the industry-manufactured/synthetic pesticides (SPTCs - e.g., herbicides, insecticides, fungicides, bactericides, nematicides, acaricides, avicides, and so on) is one of them. However, it has been later revealed that the usage of SPTCs has negatively impacted the environment - especially water and soil, and also agricultural products - mainly foods. Though preventive measures are taken by government agencies, still the utilization rate of SPTCs is high, and consequently, their maximum residual limit (MRL) levels in food are above tolerance, which further results in serious health concerns in humans. So, there is an immediate need for decreasing the utilization of the SPTCs by delivering them effectively at reduced levels in agriculture but with the required efficacy. Apart from that, it is mandatory to detect/sense and also to remove them to lessen the environmental pollution, while developing effective alternative techniques/technologies. Among many suitable materials that are developed/idenified, chitosan, a bio-polymer has gained great attention and is comprehensively implemented in all the above-mentioned applications - sensing, delivery and removal, due to their excellent and required properties. Though many works are available, in this work, a special attention is given to chitosan and its derivatives (i.e., chitosan nanoparticles (CNPs))based removal, controlled release and sensing of the SPTCs - specifically herbicides and insecticides. Moreover, the chitosan/CNPs-based protective effects on the in vivo models during/after their exposure to the SPTCs, and the current technologies like clustered regularly interspaced short palindromic repeats (CRISPR) as alternatives for SPTCs are also reviewed.

Magnetite-sepiolite nanoarchitectonics for improving zein-based bionanocomposite foams

Magnetic nanoarchitectures have been used to introduce multifunctionality in biopolymeric matrices. Bionanocomposite foams based on the corn protein zein were prepared for the first time using the hydrophobic properties of zein in a sequential treatment consisting of the removal of ethanol-soluble fractions, followed by the water swelling of the remaining phase and a further freeze-drying process. When this protocol is applied to zein pellets, they can be consolidated as porous monoliths. Moreover, it is possible to incorporate diverse types of inorganic nanoparticles in the starting pellet to produce the bionanocomposite foams. In particular, the preparation of superparamagnetic foams has been explored using two approaches: the direct incorporation of magnetite nanoparticles in a ferrofluid by impregnation in the foams, and the application of the foaming process to mixtures of zein with magnetite nanoparticles alone or previously assembled into sepiolite clay fibers. The first methodology leads to the production of inhomogeneous foams, while the use of magnetite nanoparticles and better Fe3O4-sepiolite nanoarchitectured materials as fillers results in more homogeneous materials with improved water stability and mechanical properties, offering superparamagnetic behavior. The resulting multifunctional foams have been tested in adsorption processes using the herbicide 4-chloro-2-methylphenoxyacetic acid as a model pollutant, confirming their potential utility in decontamination applications in open waters as they can be easily recovered from the aqueous medium using a magnet.

The study of the removal of penconazole fungicide from surface water using carboxymethyl tragacanth-based hydrogel grafted with poly (acrylic acid-co-acrylamide)

In this study, a polymeric adsorbent based on carboxymethyl tragacanth (CMT) grafted by poly acrylic acid-co-acrylamide (AAc-co-AAm) synthesized by radical polymerization for the first time was used to remove the fungicide penconazole (PEN) or Topas 20% from surface water. The parameters of solution pH, adsorption isotherm, and adsorption kinetics of PEN were studied by the synthetic adsorbent. The surface morphology and functional groups of CMT-g-poly (AAc-co-AAm) were confirmed by XRD, SEM and FT-IR techniques. Adsorption of PEN on CMT-g-poly (AAc-co-AAm) follows the Freundlich and pseudo-second-order models. The significant maximum adsorption capacity of the synthesized polymer was found to be 196.08 mg/g. The synthetic adsorbent had good reproducibility in PEN removal for up to 5 cycles. CMT-g-poly (AAc-co-AAm) is a cost-effective and non-toxic adsorbent for the decontamination of surface water from pesticides.

Fabrication of lanthanum/chitosan co-modified bentonite and phosphorus removal mechanism from low-concentration landscape water

It is essential to solve the problem of phosphorus pollution in urban landscape water and reduce the degree of eutrophication. In this paper, lanthanum-modified bentonite (La-B) was prepared by high-temperature calcination and liquid-phase precipitation. Then La-B was modified with chitosan to prepare a low-cost environment-friendly functional material: lanthanum/chitosan co-modified bentonite (La-BC). It can reach the adsorption equilibrium within 30 min, and the maximum adsorption capacity is 15.5 mg/g (initial phosphate concentration 50 mg/L); when the target concentration is 2 mg/L, the removal rate can reach 98.5%. La-BC has a stronger anti-interference ability to common coexisting anions SO₄^2-, HCO₃^-, NO₃^- and Cl^- in the urban landscape water body. La-BC has excellent performance in weakly acidic to neutral water, and its pH applicable range has been improved, making it possible to apply in practical water. The fitting results show that the adsorption behavior conforms to the pseudo-second-order kinetic model and the Freundlich model. After 5 regenerations, the removal efficiency remained around 80%. In the actual water test results, the phosphate concentration can be controlled below 0.1 mg/L and the removal rate is above 75%. Due to its low cost and reusability, it has great potential in the practical application of phosphate removal from landscape water.

Macroporous 3D Chitosan Cryogels for Fastac 10EC Pesticide Adsorption and Antibacterial Applications

The pesticide pollution of surface water and wastewater has been recognized as a major worldwide concern due to their persistence in the aquatic environment and the potential adverse effects on human, flora, and fauna health. Apart from pesticides, bio-contamination with various bacterial populations leads to waterborne diseases. Hence, it becomes vital to remove the above-mentioned pollutants from water using a suitable process. Consequently, our study emphasized the potential benefits of a highly porous, chemically cross-linked 3D chitosan (CSGA) cryogel in the removal of pesticides and bacteria. The CSGA sponges were prepared using a facile and cost-effective approach that consisted of a three-step cryogenic process: (i) freezing at −18 °C, (ii) storage in a frozen state for a certain period, and (iii) thawing at room temperature. Batch adsorption experiments were performed under different environments, where the effects of several parameters, such as pH, contact time, and initial pollutant concentration were evaluated to identify the appropriate adsorption conditions for maximum pesticide removal. The CSGA-based cryogel sponges exhibited a theoretical maximum adsorption capacity of 160.82 mg g⁻¹ for the Fastac 10EC pesticide and very good recyclability at room temperature. In addition, the antibacterial activities of these sponges were also investigated against various bacterial pathogens. The rates of killing Escherichia coli, Listeria monocytogenes, and Staphylococcus aureus were close to 82%, 100%, and 99%, respectively. These results demonstrated that CSGA cryogels could be efficiently used in water remediation and find applications in the removal of pesticides and disinfection.

Chitosan based adsorbents for the removal of phosphate and nitrate: A critical review

The tremendous development in the industrial sector leads to discharging of the several types of effluents containing detrimental contaminants into water sources. Lately, the proliferation of toxic anions particularly phosphates and nitrates onto aquatic systems certainly depreciates the ecological system and causes a deadly serious problem. Chitosan (Cs) is one of the most auspicious biopolymer adsorbents that are being daily developed for removing of various contaminants from polluted water. This is due to its unparalleled benefits involving biocompatibility, non-toxicity, facile modifications and low-cost production. Nevertheless, chitosan displays considerable drawbacks including low adsorption capacity, low surface area and lack of reusability. Therefore, few findings have been established regarding the aptitude of modified chitosan-based adsorbents towards phosphate and nitrate anions. This review elaborates an overview for the current advances of modified chitosan based-adsorbent for phosphate and nitrate removal, in specific multivalent metals-modified chitosan, clays and zeolite-modified chitosan, magnetic chitosan and carbon materials-modified chitosan. The efforts that have been executed for enriching their adsorption characteristics as well as their possible adsorption mechanisms and reusability were well addressed. Besides, the research conclusions for the optimum adsorption conditions were also discussed, along with emphasizing the foremost research gaps and future potential trends that could motivate further research and innovation to find best solutions for water treatment problems facing the world.

Nanocomposite and bio-nanocomposite polymeric materials/membranes development in energy and medical sector: A review

Nanocomposite and bio-nanocomposite polymer materials/membranes have fascinated prominent attention in the energy as well as the medical sector. Their composites make them appropriate choices for various applications in the medical, energy and industrial sectors. Composite materials are subject of interest in the polymer industry. Different kinds of fillers, such as cellulose-based fillers, carbon black, clay nanomaterials, glass fibers, ceramic nanomaterial, carbon quantum dots, talc and many others have been incorporated into polymers to improve the quality of the final product. These results are dependent on a variety of factors; however, nanoparticle dispersion and distribution are major obstacles to fully using nanocomposites/bio-nanocomposites materials/membranes in various applications. This review examines the various nanocomposite and bio-nanocomposite materials applications in the energy and medical sector. The review also covers the variety of ways for increasing nanocomposite and bio-nanocomposite materials features, each with its own set of applications. Recent researches on composite materials have shown that polymeric nanocomposites and bio-nanocomposites are promising materials that have been intensively explored for many applications that include electronics, environmental remediation, energy, sensing (biosensor) and energy storage devices among other applications. In this review, we studied various nanocomposite and bio-nanocomposite materials, their controlling parameters to develop the product and examine their features and applications in the fields of energy and the medical sector.

Microfluidic encapsulation for controlled release and its potential for nanofertilisers

Nanotechnology is increasingly being utilized to create advanced materials with improved or new functional attributes. Converting fertilizers into a nanoparticle-form has been shown to improve their efficacy but the current procedures used to fabricate nanofertilisers often have poor reproducibility and flexibility. Microfluidic systems, on the other hand, have advantages over traditional nanoparticle fabrication methods in terms of energy and materials consumption, versatility, and controllability. The increased controllability can result in the formation of nanoparticles with precise and complex morphologies (e.g., tuneable sizes, low polydispersity, and multi-core structures). As a result, their functional performance can be tailored to specific applications. This paper reviews the principles, formation, and applications of nano-enabled delivery systems fabricated using microfluidic approaches for the encapsulation, protection, and release of fertilizers. Controlled release can be achieved using two main routes: (i) nutrients adsorbed on nanosupports and (ii) nutrients encapsulated inside nanostructures. We aim to highlight the opportunities for preparing a new generation of highly versatile nanofertilisers using microfluidic systems. We will explore several main characteristics of microfluidically prepared nanofertilisers, including droplet formation, shell fine-tuning, adsorbate fine-tuning, and sustained/triggered release behavior.

Effect of 4-chloro-2-methylphenoxy acetic acid on tomato gene expression and rhizosphere bacterial communities under inoculation with phosphate-solubilizing bacteria

The herbicide 4-chloro-2-methylphenoxy acetic acid (MCPA) is widely used to control the spread of broad-leaved weeds in agricultural soils, though it remains unclear how tomato plants cope with the phytotoxic effects of MCPA at the molecular level. In this study, RNA-seq and Illumina MiSeq were used to sequence bacterial communities in tomato rhizosphere soils treated with MCPA and the phosphate-solubilizing bacterial strain N3. The results showed that MCPA induced abnormal growth of lateral roots in tomato seedlings and reduced uptake of the nutrients N, P, and K as well as the hormone (ABA and GA3) levels. Inoculation with strain N3 increased nutrient uptake by roots and increased levels of the hormones ABA, ZEA, and JA in tomato seedlings and also increased the abundance of the phyla Proteobacteria and Gemmatimonadetes in soil under MCPA treatment. GO functional groups in which differentially expressed genes (DEGs) are involved included DNA binding transcription factor activity, transcriptional regulator activity, enzyme inhibitor activity, and cell wall biogenesis. The highest numbers of DEGs are annotated to ribosome, photosynthesis, and carbon metabolism categories. Our findings provide valuable information for the application of strain N3, which is beneficial for reducing the toxic effect of MCPA on vegetable plants.

A review on chitosan and chitosan-based bionanocomposites: Promising material for combatting global issues and its applications

Over the last few years, several attempts have been made to replace petrochemical products with renewable and biodegradable components. The most challenging part of this approach is to obtain bio-based materials with properties and functions equivalent to those of synthetic products. Various naturally occurring polymers such as starch, collagen, alginate, cellulose, and chitin represent attractive candidates as they could reduce dependence on synthetic products and consequently positively impact the environment. Chitosan is also a unique bio-based polymer with excellent intrinsic properties. It is known for its anti-bacterial and film-forming properties, has high mechanical strength and good thermal stability. Nanotechnology has also applied chitosan-based materials in its most recent achievements. Therefore, numerous chitosan-based bionanocomposites with improved physical and chemical characteristics have been developed in an eco-friendly and cost-effective approach. This review discusses various sources of chitosan, its properties and methods of modification. Also, this work focuses on diverse preparation techniques of chitosan-based bionanocomposites and their emerging application in various sectors. Additionally, this review sheds light on future research scope with some drawbacks and challenges to motivate the researchers for future outstanding research works.

Applications of chitosan in environmental remediation: A review

Environmental biotechnology is the use of biotechnology to develop and regulate biological systems for the remediation of environmental contamination. Nature has gifted ample material for remediation of its resources, among which chitosan is one of the most important and largely available biomaterial globally. Chitosan is a biopolymer obtained by deacetylation of chitin extracted from marine waste and its applications from drug delivery to food additives are broadly available. Chitosan exhibit several properties such as availability, low cost, high biocompatibility, and biodegradability. These properties make it biologically and chemically acceptable for use in various fields. Due to some limitations of pure chitosan, there has been a growing interest in modifying the chitosan in order to improve the original properties and widen the applications of pure phase chitosan. Various modified forms of chitosan and their associated applications are reviewed here with emphasis on their use in environmental remediation. The demand of chitosan in the global industrial market is growing which is briefly explained in this paper. Chitosan is used for water purification since a long time and still progress is going on for making it more efficient in the removal process. It can be used as a flocculent and coagulant, as an adsorbent for removing the contaminants like heavy metals, dyes, pesticides, antibiotics, biological contaminants from wastewater. Soil remediation using chitosan material is explained in this review. Various other applications such as drug delivery, food additives, tissue engineering are thoroughly reviewed.

A functionalized tannin-chitosan bentonite composite with superior adsorption capacity for Cr(VI)

A novel functionalized tannin-chitosan bentonite composite (TCBC) was successfully synthesized. The formation of the composite was confirmed by the X-ray diffraction (XRD) patterns and Fourier transform infrared spectroscopy (FT-IR) analysis. The pHpzc of TCBC was 3.38. The influences such as pH, dosage of TCBC, temperature and initial Cr(VI) concentration on adsorption capacity were investigated. The experimental data indicated that the almost saturated adsorption of the TCBC towards Cr(VI) in 100 min. The maximum adsorption capacity was 262.08 mg/g at 333 K with initial pH = 2.5. The adsorption kinetics of Cr(VI) on TCBC followed the pseudo-second-order kinetics model. The isothermal data were well described by the models of Langmuir, Freundlich and Temkin. The results revealed that the adsorption of Cr(VI) on TCBC existed comprehensive effects and mainly belong to the chemisorption. The TCBC could keep good performances (q e = 192.17 mg/g) in five runs, 1 M NaOH was used as eluent for desorption, which showed a high desorption efficiency. Studies showed TCBC prepared with low cost and green raw materials, and simple green preparation technology had high adsorption capacity, good reusability and acidic tolerance. By exploring the Cr(VI)-Cr(III) hybrid system, part of Cr(VI) was reduced to Cr(III) and adsorbed by TCBC. The optimal adsorption pH of Cr(III) was 5.0.

Effects of clay colloids on ciprofloxacin transport in saturated quartz sand porous media under different solution chemistry conditions

Antibiotics, a highly prevalent class of environmental organic pollutants, are becoming a matter of global concern. Clay minerals that are ubiquitous in subsurface environments may play an important role in the fate and transport of antibiotics. Taking ciprofloxacin (CIP) as a model antibiotic, this work explored the role of clay colloids (kaolinite and montmorillonite) on the adsorption and transport of CIP under different chemical solution conditions. The adsorption isotherms showed that montmorillonite colloids had a larger CIP sorption capacity than kaolinite colloids. The results of transport experiments indicated that montmorillonite colloids could promote CIP transport in saturated sand columns, but the addition of kaolinite colloids affected CIP mobility to a much smaller extent. The much stronger transport-enhancement effect of montmorillonite colloids was due to CIP adsorbed strongly to the colloids and desorption hysteresis of colloid-adsorbed CIP, likely stemming from the intercalation of this antibiotic in the interlayer of montmorillonite. Interestingly, transport of clay colloids increased with the increasing pH from 5.0 to 9.0; however, CIP transport decreased with the increasing pH in the presence of clay colloids. The observations were likely attributable to pH-dependent ciprofloxacin adsorption/desorption to clay minerals. Increasing the concentrations of NaCl and CaCl₂ generally decreased the contaminant-mobilizing ability of montmorillonite colloids, mainly by increasing the aggregation of colloids and thus, decreasing the transport of colloid-adsorbed CIP. Moreover, under the test conditions (1 mM NaCl and pH 7.0), the presence of CIP inhibited the transport of clay colloids due to the increase in aggregate size of clay colloids with the addition of CIP. Overall, these findings suggest that clay colloids with high adsorption abilities for antibiotics in the subsurface environment may act as a carrier for certain antibiotic compounds.

Is it worth using the coupled electrodialysis/electro-oxidation system for the removal of pesticides? Process modelling and role of the pollutant

This work presents the development of the electrodialysis/electro-oxidation (EDEO) technology, assessing the role of the pollutant and the modelling of the system in order to look for the key aspects for the development of the technology. According to the results obtained, it can be concluded that electrodialysis can be properly used to concentrate clopyralid, having the selected ionic exchange membranes (AMX) an adsorption capacity of 1.64 ± 0.26 mg cm^-2. Moreover, it was observed that BDD anodes exhibit a higher degradation and mineralization current efficiencies than MMO when using electro-oxidation (EO). The role of the supporting electrolyte was also assessed, observing a slight better performance of BDD with sulphate (maximum mineralization current efficiency of 80%) and a much superior degradation efficiency with chloride when selecting MMO as anode material. Regarding the EDEO technology, it was checked that this process only overcomes the performance of EO when using MMO anodes, a result that is explained by the ratio between degradation and transport rates. Finally, a simple model was presented and successfully used to predict the degradation rate constants and to simulate the performance of EDEO under different scenarios. These simulations confirm that the transport rate needs to overcome the degradation rate in order to assure a better performance of the EDEO system compared to the conventional EO. Moreover, the simulations explain the results obtained in the present and previous works revealing the key for a further development of the EDEO technology in the future.

Bionanocomposites based on chitosan intercalation in designed swelling high-charged micas

Bionanocomposites based on layered inorganic components, as clays, and polymers of biological origin, as chitosan, have a major impact in medical and environmental fields, being economical and environmentally friendly materials. Na-Mn micas (n = 2 and 4) with controlled surface charge, high cation exchange capacity and swelling behaviour, are attractive inorganic composite components that exhibit improved adsorption properties compared to other inorganic solids which makes them potentially useful for bionanocomposites. The goal of this research was to explore the potential use of those synthetic brittle micas to form eco-friendly bionanocomposites with chitosan biopolymer. Hence, chitosan-mica bionanocomposites were prepared by ion-exchange reaction between chitosan solution and synthetic high charge mica. X-ray diffraction, Fourier transform infrared spectroscopy, thermal analysis, MAS-NMR spectroscopy and zeta-potential have been employed for bionanocomposites characterization. The results showed that the adsorption of chitosan is effective, although a chitosan portion remains in the outer surface being hydrogen-bonded to the tetrahedral sheet of the silicate.

Optimizing a low added value bentonite as adsorbent material to remove pesticides from water

A local low value bentonite from Southern Spain (Raw Bentonite), previously decarbonated (Bent), was modified to improve its pesticide adsorption capacity with Fe³⁺, hexadecyltrimethylammonium (HDTMA) and the biopolymer chitosan (CH). Adsorption of pesticides on powdered samples showed that Fe³⁺ and HDTMA were appropriate modifiers for this purpose. The modification was optimized by saturation with Fe³⁺ (Bent-Fe) and hexadecyltrimethylammonium (Bent-HDTMA) and the obtained adsorbents were characterized by several physicochemical techniques (X-ray diffraction, thermogravimetric analysis, X-ray fluorescence, physisorption of N₂). Their adsorption capacity to remove three widely used pesticides in Andalusian crops (terbuthylazine, tebuconazole and MCPA) from water was assessed and compared with the commercial organoclay Cloisite® 10A (Clo10). The modified bentonites adsorbed the selected pesticides in a percentage ranging from 30 to 100%, whereas sorption on Clo10 ranged from 30 to 90%. For their possible use as filtering beds, Bent-HDTMA, Bent-Fe and Clo10 were granulated by using three different binders (colophony resin and carnauba and bee waxes) at three different mixing ratios and the water resistance and pesticide adsorption of the granules were measured. Results showed that the granulation process did not alter the pesticide adsorption capacity of the powdered modified bentonites, and both waxes granules (carnauba and bee wax) showed better behavior than resin granules. In this work, we succeeded in the preparation of granulated adsorbents derived from a low cost material with similar behavior against a high purity smectite (precursor of Cloisite® 10A). This raises an alternative for this waste material to be used in filter systems for removing pesticides from contaminated water.

The effect of chitosan-PMAA-NPK nanofertilizer on Pisum sativum plants

The use of chitosan (CS) as a carrier for slow fertilizer release is a novel trend. The potential effect of this system in agriculture is still debatable. Here, chitosan (CS) nanoparticles were obtained by polymerizing methacrylic acid (PMAA) for the entrapment of nitrogen, phosphorous and potassium (NPK) nanoparticles (NP), each at a time to form CS-PMAA-NPK NPs complex. The impact of this complex was evaluated using garden pea (Pisum sativum var. Master B) plants. Five-day-old pea seedlings were treated through their root system with CS-PMAA-NPK NPs at concentrations of 1, 0.5, 0.25, 0.125 and 0.0625 of the stock solution (R) for 1, 2, 4 and 7 days. In general, CS-PMAA-NPK NP complex reduced root elongation rate and resulted in the accumulation of starch at the root tip in a dose-dependent manner within the treated plants. Interestingly, the lowest concentrations of 0.0625 and 0.125 R had induced mitotic cell division (MI = 22.45 ± 2.68 and 19.72 ± 3.48, respectively) compared with the control (MI = 9.09 ± 3.28). In addition, some of major proteins such as convicilin, vicilin and legumin β were upregulated in plants treated with these low concentrations too. However, all concentrations used exhibited genotoxic effect on DNA based on the comet assay data after 48 h of treatment. Thus, it is highly recommended to consider the negative effects of this carrier system on plants and environment that may arise due to its accumulation in the agricultural fields.

Facile Preparation of Biocomposite from Prawn Shell Derived Chitosan and Kaolinite-Rich Locally Available Clay

A novel composite material was prepared from prawn shell derived chitosan (CHT) and locally available kaolinite-rich modified Bijoypur clay (MC) using a facile technique in which dilute acetic acid was used as a solvent for dissolving chitosan and composite fabrication whereas distilled water was used for preparing the clay dispersion. Bijoypur clay mainly consists of kaolinite clay mineral and it was modified with the dodecyl amine to make it organophilic. Morphology and properties of the composites (different weight ratio of MC and CHT) have been studied and compared with those of pure CHT and MC. Purification and modification of Bijoypur clay were investigated by X-ray diffraction (XRD), X-ray fluorescence (XRF), and Fourier transformed infrared spectroscopy (FTIR) analyses. The fabrication of CHT-MC composites was confirmed by FTIR analysis. Thermogravimetric analysis (TGA) and differential scanning colorimetry (DSC) were used to investigate the thermal stability of the composites. It was observed that dispersed clay improves the thermal stability and enhances the hardness of the matrix systematically with the increase of clay loading. In this study, a better insolubility in both acidic and alkaline media of the composites is also observed compared to pure chitosan.

Imazamox-clay complexes with chitosan- and iron(III)-modified smectites and their use in nanoformulations

BACKGROUND

Imazamox is an ionisable herbicide, weakly retained and with high soil vertical mobility, that is used for the control of the root-parasitic plants Orobanche spp. A natural smectite (SW) modified with the biopolymer chitosan (Ch) or with Fe(3+) cation was assayed as adsorbent or carrier for imazamox controlled-release formulations (CRFs).

RESULTS

The greatest adsorption (74%) was observed for SWFe at high initial concentration (500 µM) and low pH (4.3). The interaction mechanism of imazamox on SWFe implies interlayer polar adsorption, followed by protonation of the imidazolinone ring, whereas ionic, polar and hydrophobic interactions seemed to occur in imazamox adsorption on SWCh. The herbicide release into water was inversely related to the strength of the imazamox-clay interactions and ranged in the first 10 min for imazamox-SWFe and imazamox-SWCh complexes from 27 to 75%, whereas commercial imazamox released 86%. The imazamox-SWCh weak complex (SWCh6 WC) showed similar herbicidal activity to the commercial formulation but produced a reduction of 15% in the total soil leaching losses and a reduction of 40% in the peak maximum concentration in soil column leachates.

CONCLUSION

The imazamox-clay weak complex (WC) of SWFe and SWCh and the strong complex (SC) with SWCh showed appropriate behaviour as nanopesticides or smart delivery systems to be incorporated in CRFs. © 2015 Society of Chemical Industry.

Chitosan Effects on Plant Systems

Chitosan (CHT) is a natural, safe, and cheap product of chitin deacetylation, widely used by several industries because of its interesting features. The availability of industrial quantities of CHT in the late 1980s enabled it to be tested in agriculture. CHT has been proven to stimulate plant growth, to protect the safety of edible products, and to induce abiotic and biotic stress tolerance in various horticultural commodities. The stimulating effect of different enzyme activities to detoxify reactive oxygen species suggests the involvement of hydrogen peroxide and nitric oxide in CHT signaling. CHT could also interact with chromatin and directly affect gene expression. Recent innovative uses of CHT include synthesis of CHT nanoparticles as a valuable delivery system for fertilizers, herbicides, pesticides, and micronutrients for crop growth promotion by a balanced and sustained nutrition. In addition, CHT nanoparticles can safely deliver genetic material for plant transformation. This review presents an overview on the status of the use of CHT in plant systems. Attention was given to the research that suggested the use of CHT for sustainable crop productivity.

Chitosan-Montmorillonite Polymer Composites: Formulation and Evaluation of Sustained Release Tablets of Aceclofenac

The present study reports the preparation and evaluation of polymer composites of chitosan and montmorillonite. The prepared polymer composites were evaluated for various powder properties and characterized by FTIR-ATR (Fourier Transform Infrared Spectroscopy- Attenuated Total Reflectance), XRD (X Ray Diffraction), and SEM (Scaning Electron Microscopy) techniques. Heckel and Kawakita equations indicated good compression characteristics of the composites. The polymer composites were employed in formulating sustained release tablets of aceclofenac. The formation of intercalated lamellar structures due to the entrapment of clay particles in the polymeric matrix network was found to be responsible for the drug release retardant behavior of the composites. The in vitro drug release data were fitted to various models like zero-order, first-order, Higuchi, Korsmeyer-Peppas, and Hixon and Crowell for studying the mechanism of drug release from the formulation. The value of release exponent (n) was found to range between 0.59 and 0.82, indicating non-Fickian (anomalous) drug release behavior. Swelling-induced diffusion of the drug through the polymer matrix and polymer matrix chain relaxation appeared to play a role in the release of the drug from the polymer composites.

Chitosan-based adsorption and freeze deproteinization: Improved extraction and purification of synthetic colorants from protein-rich food samples

A freeze method for deproteinization coupling with the chitosan purification process was developed for the determination of 8 synthetic food colorants in protein-rich samples. The solvents for extraction and different methods for deproteinization were examined and selected. Chitosan was employed for the purification after deproteinization, and further compared with the traditional polyamine purification method. Determination of the purified extract was conducted through the separation using high performance liquid chromatography and detection by multi-wavelength mode. Under the optimum conditions, the method showed good linearity between 0.6 and 10mg/kg, for the 8 synthetic colorants, and the limit of detection was between 0.1 and 0.4 mg/kg as was defined when the ratio of signal to noise was three. The recoveries of the spiked samples were found to be between 83% and 91%. The intra-day precision and inter-day precision was estimated to be 3-10% and 6-12%, respectively. The developed method could be applied to deproteinization and clean-up for pretreatment of protein-rich samples.

Silver-gelatine bionanocomposites for qualitative detection of a pesticide by SERS

Gelatine based nanocomposites incorporating Ag nanoparticles as a new SERS platform for the detection of diethyldithiocarbamate (EtDTC), aiming controlled release applications.

Magnetic mesoporous imprinted adsorbent based on Fe3O4-modified sepiolite for organic micropollutant removal from aqueous solution

A novel magnetic molecularly imprinted polymer adsorbent based on a magnetic sepiolite composite was successfully prepared for the first time. It has a maximum adsorption capacity of 69.53 mg g⁻¹for atrazine.

Environmental applications of chitosan and its derivatives

Chitosan originates from the seafood processing industry and is one of the most abundant of bio-waste materials. Chitosan is a by-product of the alkaline deacetylation process of chitin. Chemically, chitosan is a polysaccharide that is soluble in acidic solution and precipitates at higher pHs. It has great potential for certain environmental applications, such as remediation of organic and inorganic contaminants, including toxic metals and dyes in soil, sediment and water, and development of contaminant sensors. Traditionally, seafood waste has been the primary source of chitin. More recently, alternative sources have emerged such as fungal mycelium, mushroom and krill wastes, and these new sources of chitin and chitosan may overcome seasonal supply limitations that have existed. The production of chitosan from the above-mentioned waste streams not only reduces waste volume, but alleviates pressure on landfills to which the waste would otherwise go. Chitosan production involves four major steps, viz., deproteination, demineralization, bleaching and deacetylation. These four processes require excessive usage of strong alkali at different stages, and drives chitosan's production cost up, potentially making the application of high-grade chitosan for commercial remediation untenable. Alternate chitosan processing techniques, such as microbial or enzymatic processes, may become more cost-effective due to lower energy consumption and waste generation. Chitosan has proved to be versatile for so many environmental applications, because it possesses certain key functional groups, including - OH and -NH2 . However, the efficacy of chitosan is diminished at low pH because of its increased solubility and instability. These deficiencies can be overcome by modifying chitosan's structure via crosslinking. Such modification not only enhances the structural stability of chitosan under low pH conditions, but also improves its physicochemical characteristics, such as porosity, hydraulic conductivity, permeability, surface area and sorption capacity. Crosslinked chitosan is an excellent sorbent for trace metals especially because of the high flexibility of its structural stability. Sorption of trace metals by chitosan is selective and independent of the size and hardness of metal ions, or the physical form of chitosan (e.g., film, powder and solution). Both -OH and -NH2 groups in chitosan provide vital binding sites for complexing metal cations. At low pH, -NH3 + groups attract and coagulate negatively charged contaminants such as metal oxyanions, humic acids and dye molecules. Grafting certain functional molecules into the chitin structure improves sorption capacity and selectivity for remediating specific metal ions. For example, introducing sulfur and nitrogen donor ligands to chitosan alters the sorption preference for metals. Low molecular weight chitosan derivatives have been used to remediate metal contaminated soil and sediments. They have also been applied in permeable reactive barriers to remediate metals in soil and groundwater. Both chitosan and modified chitosan have been used to phytoremediate metals; however, the mechanisms by which they assist in mobilizing metals are not yet well understood. In addition, microbes have been used in combination with chitosan to remediate metals (e.g., Cu and Zn) in contaminated soils. Chitosan has also been used to remediate organic contaminants, such as oil-based wastewater, dyes, tannins, humic acids, phenols, bisphenoi-A, p-benzoquinone, organo-phosphorus insecticides, among others. Chitosan has also been utilized to develop optical and electrochemical sensors for in-situ detection of trace contaminants. In sensor technology, naturally-derived chitosan is used primarily as an immobilizing agent that results from its enzyme compatibility, and stabilizing effect on nanoparticles. Contaminant-sensing agents, such as enzymes, microbes and nanoparticles, have been homogeneously immobilized in chitosan gels by using coagulating (e.g., alginate, phosphate) or crosslinking agents (e.g., GA, ECH). Such immobilization maintains the stability of sensing elements in the chitosan gel phase, and prevents inactivation and loss of the sensing agent. In this review, we have shown that chitosan, an efficient by-product of a waste biomaterial, has great potential for many environmental applications. With certain limitations, chitosan and its derivatives can be used for remediating contaminated soil and wastewater. Notwithstanding, further research is needed to enhance the physicochemical properties of chitosan and mitigate its deficiencies.