Selective and efficient adsorption of Au (III) in aqueous solution by Zr-based metal-organic frameworks (MOFs): An unconventional way for gold recycling

An O/N/S-rich porous Fe-based metal-organic framework (MOF) for gold recovery from the aqueous phase with excellent performance

Recovering gold from wastewater has both economic and environmental benefits. However, how to effectively recover it is challenging. In this work, a novel Fe-based metal-organic framework (MOF) was synthesized and decorated with 2,5-thiophenedicarboxylic acid to have a well-developed porous architecture to effectively recover Au(III) from water. The maximum Au(III) sorption capacity by the finally-synthesized porous material MIL-101(Fe)-TDCA reached 2350 mg/g at pH = 6.00 ± 0.15, which is one of the highest among all literature-reported relevant materials including MOFs, and high sorption strength can be maintained within a wide pH range from 2.0 to 10.0. Besides, Au(III) sorption efficiency at low concentrations (i.e., 3.5 × 104 mg/mL) reached over 99%. Mechanically, outstanding Au(III) sorption by MIL-101(Fe)-TDCA resulted from the O/N/S-containing moieties on its surface, large surface area and porosity. The N- and S-containing functionalities (CS, CONH) served as electron donors to chelate Au(III). The O-containing (FeOFe, COFe, COOH, and coordinated H2O) and N-containing (CONH) moieties on MIL-101(Fe)-TDCA interacted with OH groups on the hydrolyzed species of Au(III) (AuCl3(OH)-, AuCl2(OH)2-, and AuCl(OH)3-) by hydrogen bond, which further increased Au(III) sorption. Furthermore, about 45.71% of Au(III) was reduced to gold nanoparticles by CS groups on the decorated 2,5-dithiophene dicarboxylic acid during sorption on MIL-101(Fe)-TDCA. Over 98.35% of Au(III) was selectively sorbed on MIL-101(Fe)-TDCA at pH 4.0, much higher than that of the coexisting heavy metal ions including Cu(II), Zn(II), Pb(II), and Ni(II) (< 5%), despite their same concentration at 0.01 mg/mL. Although sorption selectivity of a noble metal Pt(IV) by MIL-101(Fe)-TDCA is relatively poor (68.23%), it could be acceptable. Moreover, reusability of MIL-101(Fe)-TDCA is also excellent, since above 90.5% Au(III) still can be sorbed after two sorption-desorption cycles. Overall, excellent sorption performance and the roughly-calculated gold recycling benefits (26.30%) highlight that MIL-101(Fe)-TDCA is a promising porous material for gold recovery from the aqueous phase.

Enhanced Removal of Ultratrace Levels of Gold from Wastewater Using Sulfur-Rich Covalent Organic Frameworks

In view of the increasing global demand and consumption of gold, there is a growing need and effort to extract gold from alternative sources besides conventional mining, e.g., from water. This drive is mainly due to the potential benefits for the economy and the environment as these sources contain large quantities of the precious metal that can be utilized. Wastewater is one of these valuable sources in which the gold concentration can be in the ppb range. However, the effective selective recovery and recycling of ultratrace amounts of this metal remain a challenge. In this article, we describe the development of a covalent imine-based organic framework with pores containing thioanisole functional groups (TTASDFPs) formed by the condensation of a triazine-based triamine and an aromatic dialdehyde. The sulfur-functionalized pores served as effective chelating agents to bind Au3+ ions, as evidenced by the uptake of more than 99% of the 9 ppm Au3+ solution within 2 min. This is relatively fast kinetics compared with other adsorbents reported for gold adsorption. TTASDFP also showed a high removal capacity of 245 mg·g-1 and a clear selectivity toward gold ions. More importantly, the material can capture gold at concentrations as low as 1 ppb.

An N-Rich Polymer for the Selective Recovery of Gold from Wastewater

The recovery of valuable gold from wastewater is of great interest because of the widespread use of the precious metal in various fields and the pollution generated by gold-containing wastes in water. In this paper, a water-insoluble cross-linked adsorbent material (TE) based on cyanuric chloride (TCT) and ethylenediamine (EDA) was designed and used for the adsorption of Au(III) from wastewater. It was found that TE showed extremely high selectivity (D = 49,213.46) and adsorption capacity (256.19 mg/g) for Au(III) under acidic conditions. The adsorption rate remained above 90% eVen after five adsorption-desorption cycles. The adsorption process followed the pseudo-first-order kinetic model and the Freundlich isotherm model, suggesting that physical adsorption with a multilayer molecular overlay dominates. Meanwhile, the adsorption mechanism was obtained by DFT calculation and XPS analysis, and the adsorption mechanism was mainly the electrostatic interaction and electron transfer between the protonated N atoms in the adsorbent (TE) and AuCl4-, which resulted in the redox reaction. The whole adsorption process was the result of the simultaneous action of physical and chemical adsorption. In conclusion, the adsorbent material TE shows great potential for gold adsorption and recovery.

Solvothermal Preparation of Microporous Polyureas for Au(III) Adsorption

The enrichment and recovery of gold from wastewater are an alternative method to obtain this noble metal, which benefits reducing hazardous emissions from the conventional ore mining process and reserving natural gold for sustainable development. Inspired by our previous work (Lei et al., Macromol. Rapid Comm. 2022, 2200712), four families of microporous polyureas (mPPUs) with a large surface area (690 m2 g-1) and abundant heteroatom sites have been prepared via the factor-optimized solvothermal protocol. The resultant sample NPU-A starting from 1,5-naphthalene diisocyanate (NDI) and tri(4-aminophenyl) amine (TAPA) exhibits the maximum Au(III) adsorption capacity of 1300 mg g-1 and high selectivity even when the Au(III) concentration is as low as 0.1 mg L-1. This study not only demonstrates the robustness of the high-throughput synthetic strategy but also promotes the investigation of the structure-activity correlation between the mPPU chemical structure and Au(III) adsorption performance.

Variations in the concentration, inventory, source, and ecological risk of polycyclic aromatic hydrocarbons in sediments of the Lake Chaohu

In this study, the ecological risk assessment of PAHs pollution, the existing S-T model was improved and applied to this PAHs pollution assessment in surface sediment in Lake Chaohu. The potential sources and contributions of PAHs in the surface sediment were estimated by molecular diagnostic ratio (MDR) and positive matrix factorization (PMF). The results showed that the average concentration of 16 priority PAHs in the surface sediment was 718.16 ng/g in 2009 and 334.67 ng/g in 2020. In 2020, PAHs concentration has decreased compared to 2009 and the dominant composition has changed from high- to low-molecular-weight PAHs. The estimated PAHs mass inventory of the top 2 cm surface sediment was 2712 tons in 2009 and 1263 tons in 2020. Ecosystem risk assessment by improved S-T models suggested that the overall ecosystem risk of the studied regions was acceptable.

A novel magnetic Ti-MOF/chitosan composite for efficient adsorption of Pb(II) from aqueous solutions: Synthesis and investigation

In this investigation, a composite material comprising Ti-MOF and chitosan, denoted as BD-MOF(Ti)@CS/Fe3O4, was successfully designed for the efficient adsorption of Pb(II) from aqueous solutions. A comprehensive array of characterization techniques, including SEM, XRD, BET, FT-IR, and XPS, were meticulously employed to scrutinize the structural attributes and morphological features of the Pb(II) adsorbent. Notably, the material exhibits adaptability to a broad pH range, with adsorption efficiency reaching 99 % between pH 3 and 6. Kinetic studies reveal that the adsorption process of Pb(II) by BD-MOF(Ti)@CS/Fe3O4 adheres closely to a pseudo-second-order kinetic model. Impressively, within a short duration of 40 min, the adsorption efficiency can reach 85 %. Furthermore, the adsorption isotherm aligns with the Hill isotherm model, signifying cooperative adsorption. This observation underscores the synergistic interplay among the functional groups on the surface of BD-MOF(Ti)@CS/Fe3O4 in capturing Pb(II). As per the Hill model, the theoretical maximum capacity was an impressive 944.9 mg/g. Thermodynamic assessments suggested that the adsorption process was spontaneous, entropy increasing and exothermic. Even in the presence of various interfering ions, BD-MOF(Ti)@CS/Fe3O4 exhibited robust adsorption performance, thereby affirming its utility in complex environments. Moreover, the material demonstrates noteworthy reusability, sustaining effective Pb(II) removal across five consecutive cycles in aqueous solutions.

Tailoring hierarchical nanostructures of tannin acid/alginate beads for straightforward selective recovery of high-purity Au(0) from aqueous solution

The utilization of biomass materials with functional properties and rational porous structures holds significant potential for the recovery of precious metals from secondary resources, while facing challenges in achieving rapid reduction and high recovery rates of metallic Au(0). Herein, a novel concept of achieving high-purity Au(0) efficiently by tailoring tannin acid (TA) architecture and porous structure of TA-functionalized alginate beads (P-TOSA). Optimized by structural engineering, the hierarchically nanostructured P-TOSA beads demonstrate exceptional selectivity and recovery capacity (756.1 ± 2.7 mg/g at pH 5), while maintaining a recovery efficiency of over 99 % across a broad range of pH values (1.0-8.0) through the synergistic combination of chelation-based chemisorption and phenolic groups-based redox reaction. Notably, the TA-based nanostructure-boosted reduced Au(0) served as nucleation sites, facilitating elongation and migration of gold crystals across the vein network, thus forming a shell composed with 90.4 ± 0.4 % of element gold. UV radiation exposure could further generate a dynamic redox system and expedite Au (III) reduction to ultra-high purity Au(0) (93.3 ± 1.1 %) via abnormal grain growth mode. Therefore, this study presents a practical and straightforward approach utilizing biomass microbeads for recycling precious metals in metallic form without the use of toxic eluents or additional reductants.

Adsorption of Pd(II) ions by electrospun fibers with effective adsorption sites constructed by N, O atoms with a particular spatial configuration: Mechanism and practical applications

The separation and recovery of palladium from electronic waste (e-waste) are of great significance as they can alleviate environmental pollution and avoid resource loss. Herein, a novel nanofiber modified by 8-hydroxyquinoline (8-HQ-Nanofiber) with adsorption sites co-constructed by N and O atoms of hard bases was fabricated, which has good affinity properties for the Pd(II) ions belonging to soft acid in the leachate of e-waste. The adsorption mechanism of 8-HQ-Nanofiber for Pd(II) ions was revealed from the perspective of molecular level relied on a series of characterizations, such as FT-IR, ss-NMR, Zeta potential, XPS, BET, SEM and DFT. The adsorption of Pd(II) ions on 8-HQ-Nanofiber reached equilibrium within 30 min and the maximum uptake capacity was 281 mg/g at 318.15 K. The adsorption behavior of Pd(II) ions by 8-HQ-Nanofiber was described by the pseudo-second-order and Langmuir isotherm models. The 8-HQ-Nanofiber exhibited relatively good adsorption performance after 15 times of column adsorption. Finally, based on hard and soft acids and bases (HSAB) theory, a strategy to regulate the Lewis alkalinity of adsorption sites by specific spatial structures is proposed, which provides a new direction for the design of adsorption sites.

MIL-161 Metal-Organic Framework for Efficient Au(III) Recovery from Secondary Resources: Performance, Mechanism, and DFT Calculations

The recovery of precious metals from secondary resources is significant economically and environmentally. However, their separation is still challenging because they often occur in complex metal ion mixtures. The poor selectivity of adsorbents for gold in complicated solutions prevents further application of adsorption technology. In this study, a Zr-based MOF adsorbent, MIL-161, was synthesized using s-tetrazine dicarboxylic acid (H₂STz) as an organic ligand. MIL-161 demonstrated a high adsorption capacity of up to 446.49 mg/g and outstanding selectivity for gold(III) in a simulated electronic waste solution as a result of the presence of sulfur- and nitrogen-containing groups. In addition, the MIL-161 adsorbents were characterized using Fourier transform infrared (FT-IR), field emission scanning electron microscopy (FESEM), thermogravimetric analysis (TG), Brunner-Emment-Teller (BET), and X-ray photoelectron spectroscopy (XPS). Additionally, the adsorption kinetics, isotherms, and thermodynamics of the MOF adsorbents were also thoroughly examined. More importantly, the experimental results and DFT calculations indicate that chelation and electrostatic interactions are the main adsorption mechanisms.

Metal-organic frameworks-based microtrapper for real-time monitoring of targeted analyte and mechanism study

Interstitial fluid (ISF) provides important information of clinical value and physiological significance beyond blood tests for obtaining more precise health information and disease theranostics. Generally, current strategies are limited to simple extraction with time-consuming follow-up procedures. Facing challenges in efficient and real-time monitoring of target analytes in transdermal ISF, we develop metal-organic framework (MOF)-functionalized microneedle (MN) patches to achieve efficient antibiotics sampling, coupling direct analysis in real time mass spectrometry (DART-MS). The MOF MN microtrapper is constructed in a double-layered structure with a hard core and a better tissue penetration was accomplished. The MOF-based microtrapper manifests good in-vitro and in-vivo antibiotics tracking capability with a semi-quantitative method established. Moreover, the hydrogen-bond driven interaction is clarified by using molecular dynamics simulations (MDS) and related computational analysis. Good penetration safety is confirmed by histological analysis with promising clinical transnationality. We anticipate MOF MN-based microdevices provide a versatile minimally invasive strategy for transdermal ISF extraction and an extendable platform for a range of target molecules monitoring, including drugs, metabolites, biomarkers, et c, with promising clinical transnationality.

Selective removal of Hg(II) by UiO-66-NH2 modified by 4-quinolinecarboxaldehyde: from experiment to mechanism

In wastewater, heavy metal Hg causes serious harm to ecology, so it needs to be removed. In this paper, a novel MOF adsorbent (UiO-66-QU) was prepared by modifying UiO-66-NH₂ with 4-quinolinecarboxaldehyde, which was used to selectively remove Hg(II) from water. The adsorbent was characterized using Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET), zeta potentiometer, and X-ray photoelectron spectroscopy (XPS). In order to investigate the Hg(II) adsorption performance of UiO-66-QU, the effect of time, initial concentration, pH, and temperature were carried out. Langmuir model fitting shows that the maximum adsorption capacity of UiO-66-QU for Hg(II) is 556 mg/g at 298 K. The experimental results show that UiO-66-QU has better Hg(II) adsorption capacity than UiO-66-NH₂. The isotherm is in accordance with pseudo-second-order models. It is indicated that the adsorption process is mainly monolayer chemical adsorption. The thermodynamic parameters also indicate that the adsorption process is spontaneous and endothermic. It has excellent reusability and selectivity. XPS and the zeta potential showed that the adsorption mechanism was the complex reaction of Hg(II) with nitrogenous group. Therefore, the adsorbent has potential application prospects in removal of Hg(II) from wastewater.

Magnetic Zr-Based Metal-Organic Frameworks: A Highly Efficient Au (III) Trapper for Gold Recycling

In this work, the magnetic Zr-based MOF composites with excellent retrievability were prepared using Fe₃O₄@SiO₂ as the core and UiO-66-NH₂ as the shell. Fe₃O₄@SiO₂ core could introduce mesopores and result in capillary condensation in MOF composites, which aggravated with the dosage of Fe₃O₄@SiO₂. The as-synthesized MOF composites could be rapidly retrieved from aqueous solution via magnetic separation in 10 seconds. pH imposed an important effect on Au (III) adsorption by governing the ion exchange and electrostatic interaction between Au (III) anions and adsorbents, and the optimal adsorption happened at pH 7. The adsorption process fitted well with the pseudo-second order kinetics model and Langmuir adsorption model. The maximum adsorption capacity of Au (III) by FSUN-10 and FSUN-50 at 298 K were determined to be 611.18 mg∙g^-1 and 463.85 mg∙g^-1, respectively. Additionally, Au (III) uptakes increased with temperature. Beyond experiments, the adsorption mechanisms were thoroughly studied through systematic characterization, molecular dynamics simulation (MDS) and density functional theory (DFT) study. It was verified that Au (III) was adsorbed via coordination to hydroxyl and amino groups and was reduced to Au (I) and Au (0) by amino groups. The diffusion coefficient of Au (III) along UiO-66-NH₂ was calculated to be 5.8 × 10^-5 cm²∙s^-1. Moreover, the magnetic Zr-based MOF composites exhibit great industrial value in gold recycling with high adsorption selectivity and good recyclability.

Sustainable and efficient technologies for removal and recovery of toxic and valuable metals from wastewater: Recent progress, challenges, and future perspectives

Due to their numerous effects on human health and the natural environment, water contamination with heavy metals and metalloids, caused by their extensive use in various technologies and industrial applications, continues to be a huge ecological issue that needs to be urgently tackled. Additionally, within the circular economy management framework, the recovery and recycling of metals-based waste as high value-added products (VAPs) is of great interest, owing to their high cost and the continuous depletion of their reserves and natural sources. This paper reviews the state-of-the-art technologies developed for the removal and recovery of metal pollutants from wastewater by providing an in-depth understanding of their remediation mechanisms, while analyzing and critically discussing the recent key advances regarding these treatment methods, their practical implementation and integration, as well as evaluating their advantages and remaining limitations. Herein, various treatment techniques are covered, including adsorption, reduction/oxidation, ion exchange, membrane separation technologies, solvents extraction, chemical precipitation/co-precipitation, coagulation-flocculation, flotation, and bioremediation. A particular emphasis is placed on full recovery of the captured metal pollutants in various reusable forms as metal-based VAPs, mainly as solid precipitates, which is a powerful tool that offers substantial enhancement of the remediation processes' sustainability and cost-effectiveness. At the end, we have identified some prospective research directions for future work on this topic, while presenting some recommendations that can promote sustainability and economic feasibility of the existing treatment technologies.

Highly Efficient and Selective Gold Recovery Based on Hypercross-Linking and Polyamine-Functionalized Porous Organic Polymers

With the continuous increase of electronic products, there is an urgent need to effectively recover gold from e-waste and other secondary resources other than the original mine. Here, hypercross-linking and polyamine-functionalized porous organic polymers (Pc-POSS-POP) were designed and facially synthesized based on multiple azo-coupling polymerizations between 2,9,16,23-tetraaminophthalocyanine (H₂Pc(NH₂)₄) and octa(aminophenyl)-t8-silsesquioxane (OAPS) for the first time. The reaction requires no metal as a catalyst, thereby benefiting the purification of the product and the industrial scalability. Pc-POSS-POPs possess a hypercross-linking structure, highly conjugated frameworks, nitrogen-rich active sites, and extensively visible and near-infrared light absorption, which was utilized as an absorbent to retrieve Au (III). The results demonstrated that Pc-POSS-POPs have a high adsorption capacity (862.07 mg g^-1) and a rapid adsorption rate toward gold recycling. The maximum adsorption capacity could reach up to 1026.87 mg g^-1 as in the case of light irradiation. Due to the strong N coordination sites and the electronic interaction between the -NH₄⁺ groups of Pc-POSS-POPs and AuCl₄^-, Pc-POSS-POPs also exhibited excellent selectivity toward gold over several coordinated metals [Cr (VI), Co (II), Cd (II), Ni (II), and Hg (II)]. These properties together with the good regenerative ability and superior recyclability demonstrated that Pc-POSS-POPs possess promising potential as hypercross-linking polymers for capturing and recycling of Au (III).

Hybrid metal organic frameworks as an Exotic material for the photocatalytic degradation of pollutants present in wastewater: A review

In this world, water is considered as the Elixir for all living creatures. Human life rolls with water, and every activity depends upon water. Worldwide water resources are being contaminated due to the elevation in the population count, industrialization and urbanization. Ejection of chemicals by industries and domestic sewages remains the major reason in the destruction of natural water resources. Contaminated water with harmful microbes, chemical dyes, pesticides, and carcinogens are the root cause of many diseases and deaths of living species. In this scenario, researchers engaged in producing ultra components to remove the contaminants. Metal organic frameworks (MOF) are the desired combination of organic and inorganic materials to achieve the required target. MOFs possess unique characteristics like tunable internal structure, porosity, crystallinity and high surface area which enable them for energy and environmental application. For the past years, MOFs are concentrated more as a photocatalyst in the treatment of polluted water. These research studies discuss the improvement of photocatalytic performance of MOF by the incorporation of metals, metal coupled with nanoparticles like polymers, graphene, etc., into it to achieve the enhanced photocatalytic activity by scavenging entire chemicals and harmful microbes to retain the quality of water. The target of this review article is to focus on the state of the art research work on MOFs in photocatalytic water treatment technique.

Chitosan functionalized with N,N-(2-aminoethyl)pyridinedicarboxamide for selective adsorption of gold ions from wastewater

The recovery of gold from wastewater has always been a research hotspot. Here, a novel chitosan-based adsorbent (CS-DPDM) was successfully synthesized by functionalizing chitosan with (N, N-(2-aminoethyl))-2,6-pyridinedicarboxamide. The adsorbent was analyzed by fourier transform infrared spectroscopy (FT-IR), nuclear magnetic resonance spectroscopy (¹H NMR), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD) and zeta potential method (Zeta). To investigate the adsorption performance of CS-DPDM for Au(III), the effects of pH, temperature, adsorption time and initial concentration were discussed. The maximum adsorption capacity of CS-DPDM for Au(III) at pH 5.0 is 659.02 mg/g at 318 K. The adsorption is a spontaneous endothermic behavior, and the adsorption process follows the quasi-second-order kinetic and Langmuir isotherm models, indicating that a single layer of chemical adsorption may have occurred on the surface of the adsorbent. The competitive adsorption and repetitive experiments show that CS-DPDM has considerable selectivity and reusability for Au(III). X-ray photoelectron spectroscopy (XPS) results show that N and O functional groups adsorb Au(III) on the surface of CS-DPDM through electrostatic, chelation and reduction. These results indicate that CS-DPDM has broad application prospects in recovering gold ions from aqueous solutions.

A novel benzothiazole modified chitosan with excellent adsorption capacity for Au(III) in aqueous solutions

A novel benzothiazole modified chitosan (BCS) with excellent Au(III) adsorption performance and selectivity was prepared as adsorbents. The structure and morphology of the adsorbents were characterized by FTIR, SEM, XRD and XPS. The adsorption property of the adsorbents for Au(III) were investigated under different reaction time, initial concentration of Au(III), temperature, pH and coexisting ions. The maximum adsorption capacity of BCS for Au(III) was 1072.22 mg/g at 298 K and optimal pH = 4, which was better than that of other adsorbents reported in literature. The adsorption kinetics and isotherm models fit the pseudo-second-order and Langmuir equations. This shows that the adsorption process of Au(III) is a monolayer chemical adsorption. The adsorption process can proceed spontaneously and belong to the endothermic reaction according to the thermodynamic results. The excellent adsorption performance is mainly attributed to the ion exchange and chelation of the nitrogen, sulfur and oxygen groups on the adsorbent with gold ions. Significantly, BCS has excellent selectivity toward Au(III) and remarkable recycle performance. With the high adsorption capacity, excellent selectivity and outstanding reusability, the BCS adsorbent could be a promising candidate to adsorb Au(III) from wastewater.

Mechanism of selective gold adsorption on ion-imprinted chitosan resin modified by thiourea

Thiourea-modified chitosan-imprinted resin (IM-TUCS) and a corresponding nonimprinted resin (NIM-TUCS) were synthesized and characterized using adsorption experiments. The adsorption results showed that adsorption reached equilibrium within 4 h. The adsorption data were better fitted using the Langmuir model (R²>0.99), and the gold adsorption capacities of IM-TUCS and NIM-TUCS were 933.2 and 373.7 mg·g^-1, respectively. The IM-TUCS adsorbent was more suitable for gold than other coexisting anions and cations. The possible mechanism underlying Au(Ⅲ) adsorption on IM-TUCS was further investigated using X-ray photoelectron spectroscopy (XPS), Fourier-transform infrared spectroscopy (FTIR), and X-ray diffraction analyses. The protonation of the amino group on the resin under low pH conditions promoted Au(Ⅲ) adsorption; O, N and S in the C‒OH, C˭S and C-NH₂ groups contained in the IM-TUCS coordinated with Au(III) ions. The cross-linking of the imprinted resin provided holes that could hold Au(III), thus the imprinted resin supported more Au(III). The adsorption capacity of the IM-TUCS for Au(III) was significantly higher than that of the NIM-TUCS, which is attributed to the cross-linking of the imprinted resin. Moreover, the IM-TUCS showed specific recognition capabilities for Au(III). After elution with the eluent, IM-TUCS was reused for four cycles with a gold recovery rate of approximately 93%, revealing its high potential economic value.

Engineering of UiO-66-NH2 as selective and reusable adsorbent to enhance the removal of Au(III) from water: Kinetics, isotherm and thermodynamics

Efficient removal of gold ions from wastewater has become a hot research topic. A new metal-organic framework material (PAR-UiO-66) was prepared by post-modification of UiO-66-NH₂. A series of characterizations proved the successful preparation of PAR-UiO-66. The batch adsorption experiment was carried out. Under the room temperature (298 K) of and pH 4.0, the optimal adsorption capacity of PAR-UiO-66 for gold ions was 683.45 mg/g, which was an increase of 426.8 mg/g compared with that of UiO-66-NH₂. The adsorption of gold ions on PAR-UiO-66 accords with pseudo-second-order kinetics and Langmuir isotherm modles. The adsorption process was endothermic and spontaneous. PAR-UiO-66 has good selectivity and still has 92.5% adsorption efficiency after five repeated adsorptions. The adsorption mechanism is electrostatic attraction, reduction and chelation.

Persimmon tannin functionalized polyacrylonitrile fiber for highly efficient and selective recovery of Au(III) from aqueous solution

An efficient fibrous adsorbent (PANF-TETA-PT) was prepared via grafting triethylenetetramine (TETA) on polyacrylonitrile fiber (PANF), followed by persimmon tannin (PT) immobilizing. Detailed characterization certified that plenty amounts of amino and phenolic hydroxyl groups existed on the surface of PANF-TETA-PT, which would provide excellent active sites for Au(III) adsorption. The batch characteristic results found that the adsorption equilibrium data could be fitted well with Langmuir equation, while the obtained kinetic data were consistent with the Pseudo-second-order equation. The maximum equilibrium adsorption capacity of PANF-TETA-PT towards Au(III) (801.2 mg/g) was apparently superior than that of the reported adsorbents, and the competitive adsorption showed that PANF-TETA-PT had a good preference to adsorption Au(III) in spite of some coexisting pollutants. The characterization analysis of Scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffractometer spectrum (XRD) revealed that the electrostatic attraction and chelation dominated the uptake of Au(III) on PANF-TETA-PT, in which a part of loaded Au(III) was reduced to Au particles with the help of reductive functional groups. Thus, this adsorbent could be as a promising candidate to separation and preconcentration of Au(III) from wastewater.

Development and characterization of chitosan functionalized dialdehyde viscose fiber for adsorption of Au(III) and Pd(II)

A highly efficient fiber-based adsorbent (DAVFs-CS) was developed via decoration of chitosan (CS) on the dialdehyde viscose fibers (DAVFs) substrate, and employed to selective separation of precious metals from simulated contaminated water. The surface functionalization of the solid material was probed using the Fourier transform infrared (FT-IR), X-ray photoelectron spectroscopy (XPS), Thermogravimetric analysis (TGA) and nuclear magnetic resonance (NMR) technique. The batch characteristic results showed that the maximum uptake capacities of DAVFs-CS were higher up to 322 mg/g and 207 mg/g for Au(III) and Pd(II) at optimal pH 2.0 and 3.0, which exhibited competitiveness with the majority of the reported adsorbents. Meanwhile, the adsorption data were in accordance with Langmuir and PSO equations, which indicated that the monolayer chemisorption dominated the adsorption process. The competitive adsorption study showed that the removal efficiency of Au(III) was not susceptible to the co-existing impurities. Adsorption mechanism study revealed that the negative Au(III) or Pd(II) species were firstly adsorbed on DAVFs-CS via the protonated amino groups, subsequently the partially reduction of them to zero-valent gold and palladium with the help of reductive functional groups. Thus, DAVFs-CS could be as a promising adsorbent to recovery of precious metals owning to its unique adsorption mechanism and excellent adsorption performance.

Recent progress in environmental applications of metal-organic frameworks

Nanomaterials have aroused the interest of many researchers and become a research hotspot in recent years and metal-organic frameworks (MOFs) included in that are a class of new organic-inorganic hybrid porous materials formed through the self-assembly of organic ligands and inorganic metal ions. MOFs have been attracting increasing attention due to their structural diversification, large specific surface area, high porosity, inerratic pore space framework. These characteristics play their advantages in different fields and make some excellent achievements. This article summarizes the research progress of metal-organic framework in the field of environment especially the remarkable achievements in adsorption and provides a clear help for understanding the research progress and prospects for future research.

Highly selective enrichment of Au using enaminone covalent organic polymers (COP)

The second recovery of gold has fundamental environmental and economic significance. In this study, an enaminone covalent organic polymer (COP) was synthesized and used to recover gold from secondary resources. The ketene covalent organic polymer (COP) possessed good gold adsorption performance, and the best adsorption capacity could reach up to 1945 mg g⁻¹ at 298 K, which was superior to traditional adsorbents. Meanwhile, the synthesized COP exhibited excellent adsorption selectivity and renewability of Au³⁺. The pseudo-second-order kinetic equation and Langmuir equation were suggested for describing the adsorption process. Moreover, this gold adsorption behavior was intended to be a spontaneous, endothermic, and entropy increasing process.

The second recovery of gold has fundamental environmental and economic significance.

Transport of Au(III) from HCl Medium across a Liquid Membrane Using R3NH+Cl-/Toluene Immobilized on a Microporous Hydrophobic Support: Optimization and Modelling

By the use of the tertiary amine A327 and 1 M HCl solution as precursors, the ionic liquid A327H+Cl- was generated and used to investigate its performance in the transport of Au(III) from hydrochloric acid medium. The influence of the stirring speed (600-1800 min-1), ionic liquid concentration (1.25-50% v/v) in the membrane phase, and gold concentration (0.01-0.15 g/L) in the feed phase on metal transport have been investigated. An equation which included both equilibrium and kinetics parameters was derived, and the membrane diffusional resistance (Δm) and feed phase diffusional resistance (Δf) was estimated as 9.5 × 106 s/cm and 307 s/cm, respectively. At carrier concentrations in the 5-50% v/v range and gold concentrations in the 0.01-0.15 g/L range, metal transport is controlled by diffusion of metal species through the feed boundary layer, whereas at the lowest carrier concentrations, membrane diffusion is predominant. From the receiving solutions, gold can be recovered as gold nanoparticles.

Selective Adsorption, Reduction, and Separation of Au(III) from Aqueous Solution with Amine-Type Non-Woven Fabric Adsorbents

Herein, adsorption, separation, and reduction of Au(III) from its aqueous solution were studied with different amine-type, non-woven fabric (NF) adsorbents fabricated with radiation-induced graft polymerization. The adsorbents exhibited different adsorption capacities of Au(III) over a concentration range of hydrochloric acid (HCl) from 5 mM to 5 M, and the diethylamine (DEA)-type adsorbent performed best under all test conditions. The DEA-type adsorbent was inert toward other metal ions, including Cu(II), Pb(II), Ni(II), Zn(II) and Li(I), within the fixed concentration range of HCl. Flow-through adsorption tests indicated DEA-type adsorbent exhibited a rapid recovery and high adsorption capacity of 3.23 mmol/g. Meanwhile, DEA-type adsorbent also exhibited high selectivity and rapid extraction for Au(III) from its mixed solution with Pt(IV) and Pd(II). After adsorption, the reduction of Au(III) was confirmed by XRD spectra, TEM, and digital micrograph images. The results indicated that nano-sized Au particles were mainly concentrated on the adsorbent in 5 mM HCl solution. In 1 M HCl solution, not only nano-sized Au particles were found, but also micro-size Au plates precipitation occurred. This study provides a novel material for selective and efficient gold uptake from aqueous solution.

A Pyridyltriazol Functionalized Zirconium Metal-Organic Framework for Selective and Highly Efficient Adsorption of Palladium

This work reports the synthesis of pyridyltriazol-functionalized UiO-66 (UiO stands for University of Oslo), namely, UiO-66-Pyta, from UiO-66-NH₂ through three postsynthetic modification (PSM) steps. The good performance of the material derives from the observation that partial formylation (∼21% of -NHCHO groups) of H₂BDC-NH₂ by DMF, as persistent impurity, takes place during the synthesis of the UiO-66-NH₂. Thus, to enhance material performance, first, the as-synthesized UiO-66-NH₂ was deformylated to give pure UiO-66-NH₂. Subsequently, the pure UiO-66-NH₂ was converted to UiO-66-N₃ with a nearly complete conversion (∼95%). Finally, the azide-alkyne[3+2]-cycloaddition reaction of 2-ethynylpyridine with the UiO-66-N₃ gave the UiO-66-Pyta. The porous MOF was then applied for the solid-phase extraction of palladium ions from an aqueous medium. Affecting parameters on extraction efficiency of Pd(II) ions were also investigated and optimized. Interestingly, UiO-66-Pyta exhibited selective and superior adsorption capacity for Pd(II) with a maximum sorption capacity of 294.1 mg g^-1 at acidic pH (4.5). The limit of detection (LOD) was found to be 1.9 μg L^-1. The estimated intra- and interday precisions are 3.6 and 1.7%, respectively. Moreover, the adsorbent was regenerated and reused for five cycles without any significant change in the capacity and repeatability. The adsorption mechanism was described based on various techniques such as FT-IR, PXRD, SEM/EDS, ICP-AES, and XPS analyses as well as density functional theory (DFT) calculations. Notably, as a case study, the obtained UiO-66-Pyta after palladium adsorption, UiO-66-Pyta-Pd, was used as an efficient catalyst for the Suzuki-Miyaura cross-coupling reaction.