Preparation and characterization of crosslinked anion exchange membrane (AEM) materials with poly(phenylene ether)-based short hydrophilic block for use in electrochemical applications

Tuning Alkaline Anion Exchange Membranes through Crosslinking: A Review of Synthetic Strategies and Property Relationships

Alkaline anion exchange membranes (AAEMs) are an enabling component for next-generation electrochemical devices, including alkaline fuel cells, water and CO2 electrolyzers, and flow batteries. While commercial systems, notably fuel cells, have traditionally relied on proton-exchange membranes, hydroxide-ion conducting AAEMs hold promise as a method to reduce cost-per-device by enabling the use of non-platinum group electrodes and cell components. AAEMs have undergone significant material development over the past two decades; however, challenges remain in the areas of durability, water management, high temperature performance, and selectivity. In this review, we survey crosslinking as a tool capable of tuning AAEM properties. While crosslinking implementations vary, they generally result in reduced water uptake and increased transport selectivity and alkaline stability. We survey synthetic methodologies for incorporating crosslinks during AAEM fabrication and highlight necessary precautions for each approach.

Properties and Morphologies of Anion-Exchange Membranes with Different Lengths of Fluorinated Hydrophobic Chains

An anion-exchange electrolyte membrane, QPAF(C6)-4, polymerized with hydrophobic 1,4'-bis(3-chlorophenyl)perfluorohexane and hydrophilic (6,6'-(2,7-dichloro-9H-fluorene-9.9-diyl)bis(N,N-dimethylhexan-1-amine) is physically flexible and chemically stable. The drawbacks are relatively large water swelling and lower OH- conductivity at higher water uptakes, which are considered to be due to the entanglement of the flexible hydrophobic structure of the membrane. In this study, a QPAF(C4)-4 membrane was newly synthesized with shortened hydrophobic fluoroalkyl chains. Unexpectedly, QPAF(C4)-4 showed a higher water uptake and a lower bulk/surface conductivity than QPAF(C6)-4 possibly due to the decrease in hydrophobicity with a smaller number of fluorine atoms. The thermal stability of QPAF(C4)-4 was higher than that of QAPF(C6)-4, possibly due to the rigidity of the QAPF(C4)-4 structure. A higher mechanical strength of QAPF(C6)-4 than that of QPAF(C4)-4 could be explained by the larger interactions between molecules, as shown in the ultraviolet-visible spectrum. The interactions of molecules were understood in more detail with density functional theory calculations. Both the chemical structures of the polymers and the arrangements of the polymers in the membranes were found to influence the membrane properties.

Recent Advancements in Polysulfone Based Membranes for Fuel Cell (PEMFCs, DMFCs and AMFCs) Applications: A Critical Review

In recent years, ion electrolyte membranes (IEMs) preparation and properties have attracted fabulous attention in fuel cell usages owing to its high ionic conductivity and chemical resistance. Currently, perfluorinatedsulfonicacid (PFSA) membrane has been widely employed in the membrane industry in polymer electrolyte membrane fuel cells (PEMFCs); however, NafionTM suffers reduced proton conductivity at a higher temperature, requiring noble metal catalyst (Pt, Ru, and Pt-Ru), and catalyst poisoning by CO. Non-fluorinated polymers are a promising substitute. Polysulfone (PSU) is an aromatic polymer with excellent characteristics that have attracted membrane scientists in recent years. The present review provides an up-to-date development of PSU based electrolyte membranes and its composites for PEMFCs, alkaline membrane fuel cells (AMFCs), and direct methanol fuel cells (DMFCs) application. Various fillers encapsulated in the PEM/AEM moiety are appraised according to their preliminary characteristics and their plausible outcome on PEMFC/DMFC/AMFC. The key issues associated with enhancing the ionic conductivity and chemical stability have been elucidated as well. Furthermore, this review addresses the current tasks, and forthcoming directions are briefly summarized of PEM/AEMs for PEMFCs, DMFCs, AMFCs.

Performance and stability comparison of Aemion™ and Aemion+™ membranes for vanadium redox flow batteries

Anion exchange membranes (AEMs) have shown a significant rise in performance and durability within recent years for applications such as electrolysis and fuel cells. However, in vanadium redox-flow batteries, their use is of particular interest to lower costs and self-discharge rates compared to conventional perfluorinated sulfonic acid-based ionomers such as Nafion. In this work we evaluate the properties of two commercial AEMs, Aemion™ and Aemion+™, based on ex situ characterizations, an accelerated stress test degradation study (>1000 hours storage in highly oxidizing VO₂⁺ electrolyte at 35 °C) and electrochemical battery cycle tests. All membranes feature low ionic resistances of below 320 mΩ cm², enabling battery cycling at 100 mA cm⁻². Aemion shows considerable VO²⁺ formation within a VO₂⁺ stress test, whereas Aemion+ remains almost unaffected in the 1058 h stress test. Evaluating self-discharge data, cycling performance and durability data, Aemion+™ (50 μm thickness) features the best properties for vanadium redox-flow battery operation.

Cycling behaviour of Aemion™ (50 μm), Aemion+™ (50 μm), Aemion+™ (15 μm) and Nafion® 212 (50 μm) at 100 mA cm⁻². (a) Coulombic efficiency, (b) energy efficiency and (c) membrane resistance.

Transference Number Determination in Poor-Dissociated Low Dielectric Constant Lithium and Protonic Electrolytes

Whereas the major potential of the development of lithium-based cells is commonly attributed to the use of solid polymer electrolytes (SPE) to replace liquid ones, the possibilities of the improvement of the applicability of the fuel cell is often attributed to the novel electrolytic materials belonging to various structural families. In both cases, the transport properties of the electrolytes significantly affect the operational parameters of the galvanic and fuel cells incorporating them. Amongst them, the transference number (TN) of the electrochemically active species (usually cations) is, on the one hand, one of the most significant descriptors of the resulting cell operational efficiency while on the other, despite many years of investigation, it remains the worst definable and determinable material parameter. The paper delivers not only an extensive review of the development of the TN determination methodology but as well tries to show the physicochemical nature of the discrepancies observed between the values determined using various approaches for the same systems of interest. The provided critical review is supported by some original experimental data gathered for composite polymeric systems incorporating both inorganic and organic dispersed phases. It as well explains the physical sense of the negative transference number values resulting from some more elaborated approaches for highly associated systems.

Selectivity of Transport Processes in Ion-Exchange Membranes: Relationship with the Structure and Methods for Its Improvement

Nowadays, ion-exchange membranes have numerous applications in water desalination, electrolysis, chemistry, food, health, energy, environment and other fields. All of these applications require high selectivity of ion transfer, i.e., high membrane permselectivity. The transport properties of ion-exchange membranes are determined by their structure, composition and preparation method. For various applications, the selectivity of transfer processes can be characterized by different parameters, for example, by the transport number of counterions (permselectivity in electrodialysis) or by the ratio of ionic conductivity to the permeability of some gases (crossover in fuel cells). However, in most cases there is a correlation: the higher the flux density of the target component through the membrane, the lower the selectivity of the process. This correlation has two aspects: first, it follows from the membrane material properties, often expressed as the trade-off between membrane permeability and permselectivity; and, second, it is due to the concentration polarization phenomenon, which increases with an increase in the applied driving force. In this review, both aspects are considered. Recent research and progress in the membrane selectivity improvement, mainly including a number of approaches as crosslinking, nanoparticle doping, surface modification, and the use of special synthetic methods (e.g., synthesis of grafted membranes or membranes with a fairly rigid three-dimensional matrix) are summarized. These approaches are promising for the ion-exchange membranes synthesis for electrodialysis, alternative energy, and the valuable component extraction from natural or waste-water. Perspectives on future development in this research field are also discussed.

Ionic Transport Properties of P2O5-SiO2 Glassy Protonic Composites Doped with Polymer and Inorganic Titanium-based Fillers

This paper is focused on the determination of the physicochemical properties of a composite inorganic–organic modified membrane. The electrical conductivity of a family of glassy protonic electrolytes defined by the general formula (P₂O₅)_x(SiO₂)_y, where x/y is 3/7 are studied by Alternating Current electrochemical impedance spectroscopy (AC EIS) method. The reference glass was doped with polymeric additives—poly(ethylene oxide) (PEO) and poly(vinyl alcohol) (PVA), and additionally with a titanium-oxide-based filler. Special attention was paid to determination of the transport properties of the materials thus modified in relation to the charge transfer phenomena occurring within them. The electrical conductivities of the ‘dry’ material ranged from 10⁻⁴ to 10⁻⁹ S/cm, whereas for ‘wet’ samples the values were ~10⁻³ S/cm. The additives also modified the pore space of the samples. The pore distribution and specific surface of the modified glassy systems exhibited variation with changes in electrolyte chemical composition. The mechanical properties of the samples were also examined. The Young’s modulus and Poisson’s ratio were determined by the continuous wave technique (CWT). Based on analysis of the dispersion of the dielectric losses, it was found that the composite samples exhibit mixed-type proton mobility with contributions related to both the bulk of the material and the surface of the pore space.

Reinforced anion exchange membrane based on thermal cross-linking method with outstanding cell performance for reverse electrodialysis

A poly(ethylene)-reinforced anion exchange membrane based on cross-linked quaternary-aminated polystyrene and quaternary-aminated poly(phenylene oxide) was developed for reverse electrodialysis. Although reverse electrodialysis is a clean and renewable energy generation system, the low power output and high membrane cost are serious obstacles to its commercialization. Herein, to lower the membrane cost, inexpensive polystyrene and poly(phenylene oxide) were used as ionomer backbones. The ionomers were impregnated into a poly(ethylene) matrix supporter and were cross-linked in situ to enhance the mechanical and chemical properties. Pre-treatment of the porous PE matrix membrane with atmospheric plasma increased the compatibility between the ionomer and matrix membrane. The fabricated membranes showed outstanding physical, chemical, and electrochemical properties. The area resistance of the fabricated membranes (0.69-1.67 Ω cm2) was lower than that of AMV (2.58 Ω cm2). Moreover, the transport number of PErC(5)QPS-QPPO was comparable to that of AMV, despite the thinness (51 μm) of the former. The RED stack with the PErC(5)QPS-QPPO membrane provided an excellent maximum power density of 1.82 W m-2 at a flow rate of 100 mL min-1, which is 20.7% higher than that (1.50 W m-2) of the RED stack with the AMV membrane.

Quaternized cellulose and graphene oxide crosslinked polyphenylene oxide based anion exchange membrane

Anion exchange membrane fuel cells (AEMFCs) have captivated vast interest due to non-platinum group metal catalysts and fuel flexibility. One of the major shortcomings of AEMFCs, however, is the lack of a stable and high anion conducting membrane. This study introduces a new strategy for fabrication of high conducting anion exchange membrane (AEM) using a hybrid nanocomposite of graphene oxide (GO), cellulose, and poly(phenylene oxide) (PPO), which are functionalized with 1,4-diazabicyclo[2.2.2]octane. The compositional ratio of GO/cellulose/PPO was optimized with respect to ionic conductivity, water uptake, swelling ratio, and mechanical properties. The membrane at GO/cellulose/PPO weight ratio of 1/1/100 displayed an impressive hydroxyl conductivity of ∼114 mS/cm at 25 °C and ∼215 mS/cm at 80 °C, which is considerably higher than the highest value reported. Further, the hybrid composite membranes were mechanically stable even when operating at high temperature (80 °C). The result indicates that the introduction of quaternized GO and cellulose into a polymer matrix is a promising approach for designing high performance AEMs.

Novel Triple Tertiary Amine Polymer-Based Hydrogen Bond Network Inducing Highly Efficient Proton-Conducting Channels of Amphoteric Membranes for High-Performance Vanadium Redox Flow Battery

A novel amphoteric membrane was designed by blending triple tertiary amine-grafted poly(2,6-dimethyl-1,4-phenylene oxide) (PPO-TTA) with sulfonated poly(ether ether ketone) (SPEEK) for vanadium redox flow batteries. An "acid-base pair" effect is formed by the combination of the tertiary amine group and sulfonic group, and extra nonbonding amine groups could be protonated. Both of them constitute a hydrogen bond network, which facilitates proton conduction and also hinders vanadium permeability because of the lowered swelling ratio and Donnan effect. All these contribute to improve the ion selectivity of the membrane while maintaining ionic conductivity. Compared with other amphoteric and SPEEK-based membranes, the membrane exhibits an excellent performance. The amphoteric membrane containing 15% PPO-TTA exhibits an ultralow vanadium permeability of 3.4 × 10^-9 cm² s^-1 and a low area resistance of 0.39 Ω cm^-2. Consequently, the cell assembled with this membrane shows excellent performances far superior to SPEEK and Nafion 212. The Coulombic efficiency and energy efficiency of the cell are 94.3-98.3 and 90.3-77.1% at 40-200 mA cm^-2, respectively, and have no significant reductions after 200 cycles. This performance is at a high level among the amphoteric and SPEEK-based membranes reported in recent years. The cell's open circuit voltage is maintained for up to 165 h. In addition, the membrane's chemical stability is improved by the effective barrier to the vanadium ion.

Structurally Well-Defined Anion-Exchange Membranes Containing Perfluoroalkyl and Ammonium-Functionalized Fluorenyl Groups

Novel anion-conductive polymers containing perfluoroalkyl and ammonium-functionalized fluorene groups were synthesized and characterized. The quaternized polymers synthesized using a dimethylaminated fluorene monomer had a well-defined chemical structure in which each fluorenyl group was substituted with two ammonium groups at specific positions. The resulting polymers had a high molecular weight (M n = 8.9-13.8 kDa, M w = 13.7-24.5 kDa) to provide bendable thin membranes with the ion-exchange capacity (IEC) ranging from 0.7 to 1.9 mequiv g-1 by solution casting. Both transmission electron microscopy images and small-angle X-ray scattering patterns suggested that the polymer membranes possessed a nanoscale phase-separated morphology based on the hydrophilic/hydrophobic differences in the polymer components. Unlike typical anion-exchange membranes found in the literature, hydroxide ion conductivity of the membranes did not increase with increasing IEC because of their high swelling capability in water. The membrane with IEC = 1.2 mequiv g-1 showed balanced properties of high hydroxide ion conductivity (81 mS cm-1 at 80 °C in water) and mechanical strength (>100% elongation and 14 MPa maximum stress at 80 °C, 60% relative humidity). The polymer main chains were stable in 4 M KOH for 1000 h, whereas the trimethylbenzyl-type ammonium groups degraded under the conditions to cause loss in the hydroxide ion conductivity. An H2/O2 fuel cell with the membrane with IEC = 1.2 mequiv g-1 exhibited a maximum power density of 242 mW cm-2 at 580 mA cm-2 current density.

Semi-Interpenetrating Network-Type Cross-Linked Amphoteric Ion-Exchange Membrane Based on Styrene Sulfonate and Vinyl Benzyl Chloride for Vanadium Redox Flow Battery

Clean energy is the main requirement for human life. Redox flow battery may be an alternative to fossil fuels. An ion-exchange membrane is the heart of the redox flow battery. In the present study, we synthesize semi-interpenetrating cross-linked copolymer amphoteric ion-exchange membranes (AIEMs) with a partially rigid backbone. The styrene sulfonate and vinyl benzyl chloride monomers are used as the cationic and anionic moieties into the AIEMs. Three different types of quaternizing agents are used to convert a primary amine into a quaternary amine group. Here, we avoid the use of the carcinogenic chemical CMME, commonly used for the synthesis of anion-exchange membranes. The prepared membranes exhibit good electrochemical and physicochemical properties with a high acidic stability. The membranes also show moderate water uptake and dimensional change. The ZWMO membrane shows better properties among the AIEMs, with an ionic conductivity of 3.12 × 10^-2 S cm^-1 and 5.49 water molecules per functional group. The anion and cation-exchange capacities of the ZWMO membranes are calculated to be 1.11 and 0.62 mequiv/g. All AIEMs show good thermal and mechanical stabilities, calculated by differential scanning calorimetry, dynamic mechanical analysis, and universal testing machine analysis. The membranes show low vanadium ion permeability than the commercial membrane Nafion for their use in vanadium redox flow batteries. Further, the AIEMs are applied in redox flow batteries as separators and deliver good results with the charging and discharging phenomena, with 87% voltage efficiency and 91% current efficiency.

Polybenzimidazole/Nafion hybrid membrane with improved chemical stability for vanadium redox flow battery application

In order to increase the chemical stability of polybenzimidazole (PBI) membrane against the highly oxidizing environment of a vanadium redox flow battery (VRFB), PBI/Nafion hybrid membrane was developed by spray coating a Nafion ionomer onto one surface of the PBI membrane. The acid–base interaction between the sulfonic acid of the Nafion and the benzimidazole of the PBI created a stable interfacial adhesion between the Nafion layer and the PBI layer. The hybrid membrane showed an area resistance of 0.269 Ω cm² and a very low vanadium permeability of 1.95 × 10⁻⁹ cm² min⁻¹. The Nafion layer protected the PBI from chemical degradation under accelerated oxidizing conditions of 1 M VO₂⁺/5 M H₂SO₄, and this was subsequently examined in spectroscopic analysis. In the VRFB single cell performance test, the cell with the hybrid membrane showed better energy efficiency than the Nafion cell with 92.66% at 40 mA cm⁻² and 78.1% at 100 mA cm⁻² with no delamination observed between the Nafion layer and the PBI layer after the test was completed.

Novel polybenzimidazole (PBI)/Nafion hybrid membranes for the VRFB are made by spray coating a Nafion layer to protect PBI from chemical degradation.

The preparation and application of a ROMP-type epoxy-functionalized norbornene copolymer and its hybrid alkaline anion exchange membranes

A ROMP-type epoxy-functionalized norbornene copolymer and its hybrid alkaline anion exchange membranes were prepared and studied for DMFC application.