Nanostructured all-cellulose membranes for efficient ultrafiltration of wastewater

Impact of solvent treatment on the adsorption efficiency of crystal violet dye using cellulose acetate-clay composite membranes: Experimental and molecular dynamics approaches

The pollution of water bodies by synthetic dyes, particularly crystal violet dye (CVD), poses significant environmental and health risks due to its toxic effects. This study investigates the adsorption capabilities of cellulose acetate-clay composite membranes (RC@CA) for removing CVD from wastewater. Two types of membranes were synthesized using acetone (Ac) and acetic acid (AA) and characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA/DTA) and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM/EDS). Adsorption studies demonstrated that pH significantly influenced dye uptake, with both RC@CA membranes outperforming red clay (RC). Kinetic studies showed equilibrium was reached within 60 min, following a pseudo-second-order model. The Freundlich isotherm model indicate multilayer adsorption on heterogeneous surfaces with varying adsorption energies with capacities of 99.16 mg g-1 for RC@CA (Ac) and 97.79 mg g-1 for RC@CA (AA), compared to 47.62 mg g-1 for RC. Molecular dynamics (MD) simulations further suggested that increased acetylation enhances adsorption performance. Overall, RC@CA (Ac) membranes demonstrated the highest efficiency, highlighting its potential as a cost-effective adsorbent for wastewater.

2D Materials for Potable Water Application: Basic Nanoarchitectonics and Recent Progresses

Water polluted by toxic chemicals due to waste from chemical/pharmaceuticals and harmful microbes such as E. Coli bacteria causes several fatal diseases; and therefore, water filtration is crucial for accessing clean and safe water necessary for good health. Conventional water filtration technologies include activated carbon filters, reverse osmosis, and ultrafiltration. However, they face several challenges, including high energy consumption, fouling, limited selectivity, inefficiencies in removing certain contaminants, dimensional control of pores, and structural/chemical changes at higher thermal conditions and upon prolonged usage of water filter. Recently, the advent of 2D materials such as graphene, BN, MoS2, MXenes, and so on opens new avenues for advanced water filtration systems. This review delves into the nanoarchitectonics of 2D materials for water filtration applications. The current state of water filtration technologies is explored, the inherent challenges they face are outlines, and the unique properties and advantages of 2D materials are highlighted. Furthermore, the scope of this review is discussed, which encompasses the synthesis, characterization, and application of various 2D materials in water filtration, providing insights into future research directions and potential industrial applications.

Construction of self-repairing polyethersulfone membrane with high density hydrophilic microregions by two dimensional restricted channels for enhanced dyes/salts selective separation

Based on the dye/salts separation efficiency and membrane injury caused by serious pollution of dye/salts wastewater, this study constructed a 2D tight ultrafiltration membrane that could both solve the membrane injury problem and improve the dye/salts separation efficiency, the compatibility of good self-healing performance and penetration performance by 2D material magnesium-aluminum Layered double hydroxide (MgAl-LDH). The self-repairing of physical injury was achieved through the swelling effect of AMPS-PAN, this property was proved by permeate flux, the retention performance of salts in dye/salts solution, the comparison of scanning electron microscope (SEM), and the mechanical strength after physical injury. The healing of chemical injury occured through the reaction of CC and polyethersulfone chain breakage, which was confirmed by X-ray photoelectron spectroscopy (XPS), permeate flux, the retention performance of salts in dye/salts solution, and mechanical property. The high separation efficiency of dye/salts was achieved through 2D material MgAl-LDH, which was proved by separation selectivity ɑ. The compatibility of good self-healing performance and penetration performance was obtained by 2D material MgAl-LDH, which was proved by the penetration and self-healing performance. Morever, the membrane illustrated excellent both permeability and dye/sals separation efficiency, just like the permeate flux, the retention performance of sodium sulfate in methyl blue/sodium sulfate solution, the retention performance of Na2SO4 in methyl blue/Na2SO4 solution, the retention rate of methyl blue were 99.1 L/m2h, 12.5%, 7.9%, 97.7%, respectively. The results of pollution index and contact angle also proved that the membrane had anti-pollution performance.

Wastewater Treatment Using Membrane Bioreactor Technologies: Removal of Phenolic Contaminants from Oil and Coal Refineries and Pharmaceutical Industries

Huge amounts of noxious chemicals from coal and petrochemical refineries and pharmaceutical industries are released into water bodies. These chemicals are highly toxic and cause adverse effects on both aquatic and terrestrial life. The removal of hazardous contaminants from industrial effluents is expensive and environmentally driven. The majority of the technologies applied nowadays for the removal of phenols and other contaminants are based on physio-chemical processes such as solvent extraction, chemical precipitation, and adsorption. The removal efficiency of toxic chemicals, especially phenols, is low with these technologies when the concentrations are very low. Furthermore, the major drawbacks of these technologies are the high operation costs and inadequate selectivity. To overcome these limitations, researchers are applying biological and membrane technologies together, which are gaining more attention because of their ease of use, high selectivity, and effectiveness. In the present review, the microbial degradation of phenolics in combination with intensified membrane bioreactors (MBRs) has been discussed. Important factors, including the origin and mode of phenols' biodegradation as well as the characteristics of the membrane bioreactors for the optimal removal of phenolic contaminants from industrial effluents are considered. The modifications of MBRs for the removal of phenols from various wastewater sources have also been addressed in this review article. The economic analysis on the cost and benefits of MBR technology compared with conventional wastewater treatments is discussed extensively.

Recent advances in cellulose- and alginate-based hydrogels for water and wastewater treatment: A review

From the environmental perspective, it is essential to develop cheap, eco-friendly, and highly efficient materials for water and wastewater treatment. In this regard, hydrogels and hydrogel-based composites have been widely employed to mitigate global water pollution as this methodology is simple and free from harmful by-products. Notably, alginate and cellulose, which are natural carbohydrate polymers, have gained great attention for their availability, price competitiveness, excellent biodegradability, biocompatibility, hydrophilicity, and superior physicochemical performance in water treatment. This review outlined the recent progress in developing and applying alginate- and cellulose-based hydrogels to remove various pollutants such as dyes, heavy metals, oils, pharmaceutical contaminants, and pesticides from wastewater streams. This review also highlighted the effects of various physical or chemical methods, such as crosslinking, grafting, the addition of fillers, nanoparticle incorporation, and polymer blending, on the physiochemical and adsorption properties of hydrogels. In addition, this review covered the alginate- and cellulose-based hydrogels' current limitations such as low mechanical performance and poor stability, while presenting strategies to improve the drawbacks of the hydrogels. Lastly, we discussed the prospects and future directions of alginate- and cellulose-based hydrogels. We hope this review provides valuable insights into the efficient preparations and applications of hydrogels.

High-strength hydrophilic N-halamines chitosan and cellulose nanofibers membranes with repeated bactericidal properties

Direct addition of disinfectants and membrane separation techniques have been common methods to address microbial contamination in water. However, disinfectants may generate toxic by-products, and even minor damage or biofilm formation on filtration membranes can lead to a heightened risk of microbial contamination. Consequently, how to quickly and safely disinfect microbial contaminated water sources remains a huge challenge. In this study, the high-strength broad-spectrum antibacterial CNF/CS composite membrane was fabricated by utilizing cellulose nanofibers (CNF) to reinforce the structure of chitosan (CS). The resulting CNF/CS composite membrane exhibits an impressive tensile strength of 148 MPa and boasts an active chlorine content of 5.29 %. Notably, even after undergoing 50 washing cycles and 10 repeated chlorination procedures, the structural integrity and high active chlorine content of the composite membrane remain preserved, validating its exceptional strength, stability, and chlorine rechargeability. Additionally, the CNF/CS antibacterial materials demonstrate remarkable attributes in terms of rapid sterilization, sustained and consistent release of active chlorine, and efficient inhibition of biofilm formation, demonstrating great potential in efficient, green, and safe sterilization.

Fluorine-Containing, Self-Assembled Graft Copolymer for Tuning the Hydrophilicity and Antifouling Properties of PVDF Ultrafiltration Membranes

Neat poly(vinylidene fluoride) (PVDF) ultrafiltration (UF) membranes exhibit poor water permeance and surface hydrophobicity, resulting in poor antifouling properties. Herein, we report the synthesis of a fluorine-containing amphiphilic graft copolymer, poly(2,2,2-trifluoroethyl methacrylate)-g-poly(ethylene glycol) behenyl ether methacrylate (PTFEMA-g-PEGBEM), hereafter referred to as PTF, and its effect on the structure, morphology, and properties of PVDF membranes. The PTF graft copolymer formed a self-assembled nanostructure with a size of 7-8 nm, benefiting from its amphiphilic nature and microphase separation ability. During the nonsolvent-induced phase separation (NIPS) process, the hydrophilic PEGBEM chains were preferentially oriented towards the membrane surface, whereas the superhydrophobic PTFEMA chains were confined in the hydrophobic PVDF matrix. The PTF graft copolymer not only increased the pore size and porosity but also significantly improved the surface hydrophilicity, flux recovery ratio (FRR), and antifouling properties of the membrane. The membrane performance was optimal at 5 wt.% PTF loading, with a water permeance of 45 L m-2 h-1 bar-1, a BSA rejection of 98.6%, and an FRR of 83.0%, which were much greater than those of the neat PVDF membrane. Notably, the tensile strength of the membrane reached 6.34 MPa, which indicated much better mechanical properties than those reported in the literature. These results highlight the effectiveness of surface modification via the rational design of polymer additives and the precise adjustment of the components for preparing membranes with high performance and excellent mechanical properties.

Bio-Based Polymeric Membranes: Development and Environmental Applications

Nowadays, membrane technology is an efficient process for separating compounds with minimal structural abrasion; however, the manufacture of membranes still has several drawbacks to being profitable and competitive commercially under an environmentally friendly approach. In this sense, this review focuses on bio-based polymeric membranes as an alternative to solve the environmental concern caused by the use of polymeric materials of fossil origin. The fabrication of bio-based polymeric membranes is explained through a general description of elements such as the selection of bio-based polymers, the preparation methods, the usefulness of additives, the search for green solvents, and the characterization of the membranes. The advantages and disadvantages of bio-based polymeric membranes are discussed, and the application of bio-based membranes to recover organic and inorganic contaminants is also discussed.

Electrospun Nanofiber Membrane: An Efficient and Environmentally Friendly Material for the Removal of Metals and Dyes

With the rapid development of nanotechnology, electrospun nanofiber membranes (ENM) application and preparation methods have attracted attention. With many advantages such as high specific surface area, obvious interconnected structure, and high porosity, ENM has been widely used in many fields, especially in water treatment, with more advantages. ENM solves the shortcomings of traditional means, such as low efficiency, high energy consumption, and difficulty in recycling, and it is suitable for recycling and treatment of industrial wastewater. This review begins with a description of electrospinning technology, describing the structure, preparation methods, and factors of common ENMs. At the same time, the removal of heavy metal ions and dyes by ENMs is introduced. The mechanism of ENM adsorption on heavy metal ions and dyes is chelation or electrostatic attraction, which has excellent adsorption and filtration ability for heavy metal ions and dyes, and the adsorption capacity of ENMs for heavy metal ions and dyes can be improved by increasing the metal chelation sites. Therefore, this technology and mechanism can be exploited to develop new, better, and more effective separation methods for the removal of harmful pollutants to cope with the gradually increasing water scarcity and pollution. Finally, it is hoped that this review will provide some guidance and direction for research on wastewater treatment and industrial production.

Cellulose/inorganic nanoparticles-based nano-biocomposite for abatement of water and wastewater pollutants

Nanostructured materials offer a significant role in wastewater treatment with diminished capital and operational expense, low dose, and pollutant selectivity. Specifically, the nanocomposites of cellulose with inorganic nanoparticles (NPs) have drawn a prodigious interest because of the extraordinary cellulose properties, high specific surface area, and pollutant selectivity of NPs. Integrating inorganic NPs with cellulose biopolymers for wastewater treatment is a promising advantage for inorganic NPs, such as colloidal stability, agglomeration prevention, and easy isolation of magnetic material after use. This article presents a comprehensive overview of water treatment approaches following wastewater remediation by green and environmentally friendly cellulose/inorganic nanoparticles-based bio-nanocomposites. The functionalization of cellulose, functionalization mechanism, and engineered hybrid materials were thoroughly discussed. Moreover, we also highlighted the purification of wastewater through the composites of cellulose/inorganic nanoparticles via adsorption, photocatalytic and antibacterial approach.

Modification of Thin Film Composite Membrane by Chitosan-Silver Particles to Improve Desalination and Anti-Biofouling Performance

Reverse osmosis (RO) desalination is a technology that is commonly used to mitigate water scarcity problems; one of its disadvantages is the bio-fouling of the membranes used, which reduces its performance. In order to minimize this problem, this study prepared modified thin film composite (TFC) membranes by the incorporation of chitosan-silver particles (CS-Ag) of different molecular weights, and evaluated them in terms of their anti-biofouling and desalination performances. The CS-Ag were obtained using ionotropic gelation, and were characterized by Fourier transform infrared spectroscopy (FTIR), high-resolution scanning electron microscopy (HR-SEM), energy-dispersive X-ray spectroscopy (EDX), thermogravimetric analysis (TGA) and dynamic light scattering (DLS). The modified membranes were synthetized by the incorporation of the CS-Ag using the interfacial polymerization method. The membranes (MCS-Ag) were characterized by Fourier transform infrared spectroscopy (FTIR), atomic force microscopy (AFM) and contact angle. Bactericidal tests by total cell count were performed using Bacillus halotolerans MCC1, and anti-adhesion properties were confirmed through biofilm cake layer thickness and total organic carbon (%). The desalination performance was defined by permeate flux, hydraulic resistance, salt rejection and salt permeance by using 2000 and 5000 mg L^-1 of NaCl. The MCS-Ag-L presented superior permeate flux and salt rejection (63.3% and 1% higher, respectively), as well as higher bactericidal properties (76% less in total cell count) and anti-adhesion capacity (biofilm thickness layer 60% and total organic carbon 75% less, compared with the unmodified membrane). The highest hydraulic resistance value was for MCS-Ag-M. In conclusion, the molecular weight of CS-Ag significantly influences the desalination and the antimicrobial performances of the membranes; as the molecular weight decreases, the membranes' performances increase. This study shows a possible alternative for increasing membrane useful life in the desalination process.