Flow Behavior Prior to Crosslinking: The Need for Precursor Rheology for Placement of Hydrogels in Medical Applications and for 3D Bioprinting

Cyclodextrin modified biocompatible Chitosan-Cinnamaldehyde Schiff base hydrogels: Their antibacterial, antioxidant, and drug delivery potential

Chitosan (CS)-based hydrogels are promising platforms for drug delivery owing to their biocompatibility, biodegradability, and functional versatility. However, pure CS Schiff base hydrogels lack mechanical strength and rely on toxic cross-linkers, necessitating bio-safe alternatives viz. Cinnamaldehyde (CA). In this study, hybrid Chitosan-Cinnamaldehyde (CSCA) and Chitosan-Cinnamaldehyde-γ-Cyclodextrin (CSCDCA) hydrogels were synthesized to address the limitations. Encapsulation of CA into γ-Cyclodextrin (γ-CD) enhanced the stability of CA through the formation of an inclusion complex (IC), as confirmed by NMR analysis. CSCDCA hydrogels although relatively weaker, exhibited superior swelling/water retention capability over CSCA hydrogels. The release behavior of Rifampicin (Rif) a model hydrophobic drug, was monitored in both hydrogels. CSCDCA hydrogel showed more controlled release (∼56 % at pH 2 and 39 % at pH 7.4 over 30 h) compared to CSCA (∼70 % at pH 2 and 36 % at pH 7.4). Kinetic analysis indicated combined diffusion and relaxation mechanism of release. Antibacterial and antioxidant (AOX) activities confirmed significant activity, with CSCDCA achieving 95 % cell viability against human embryonic kidney (HEK-293) cells. These findings underscore the hydrogel's suitability as pH-sensitive drug delivery system (DDS), enhancing Rif's bioavailability, minimizing side effects, and establishing a benchmark for eco-friendly hydrogels in therapeutic applications.

Enhanced Ear Cartilage Regeneration with Dual-Network LT-GelMA/F127DA Hydrogel Featuring Nanomicelle Integration

Tissue-engineered cartilage, supported by advancements in photo-cross-linkable hydrogels, offers a promising solution for the repair and regeneration of damaged cartilage in anatomically complex and mechanically demanding sites. Low-temperature soluble GelMA (LT-GelMA) remains in a liquid state at room temperature, allowing for easier handling; however, it has limitations in mechanical strength and structural stability. To address these limitations, we developed a novel dual-network hydrogel combining LT-GelMA with Pluronic F127-diacrylate (F127DA). The resulting hydrogel uniquely integrates the low-temperature solubility of LT-GelMA with the enhanced mechanical strength provided by photo-cross-linkable F127DA nanomicelles. Additionally, the hydrogel exhibits controlled swelling and biodegradation rates. In vitro studies revealed a significant increase in chondrocyte viability by day 7 in formulations with higher F127DA concentrations. In vivo, the hydrogel demonstrated superior neo-cartilage formation in a subcutaneous nude mouse model, as indicated by increased deposition of cartilage-specific extracellular matrix components at 4 and 8 weeks. In summary, we developed a hydrogel with fluidity at room temperature and enhanced mechanical performance. These results indicate that the LT-GelMA/F127DA hydrogel effectively addresses the current gaps in cartilage tissue engineering. The hydrogel's superior performance, especially in promoting cartilage regeneration, positions it as a promising alternative for reconstructive surgery, representing a significant improvement over existing cartilage repair strategies.

Physical stimuli-responsive DNA hydrogels: design, fabrication strategies, and biomedical applications

Physical stimuli-responsive DNA hydrogels hold immense potential for tissue engineering due to their inherent biocompatibility, tunable properties, and capacity to replicate the mechanical environment of natural tissue, making physical stimuli-responsive DNA hydrogels a promising candidate for tissue engineering. These hydrogels can be tailored to respond to specific physical triggers such as temperature, light, magnetic fields, ultrasound, mechanical force, and electrical stimuli, allowing precise control over their behavior. By mimicking the extracellular matrix (ECM), DNA hydrogels provide structural support, biomechanical cues, and cell signaling essential for tissue regeneration. This article explores various physical stimuli and their incorporation into DNA hydrogels, including DNA self-assembly and hybrid DNA hydrogel methods. The aim is to demonstrate how DNA hydrogels, in conjunction with other biomolecules and the ECM environment, generate dynamic scaffolds that respond to physical stimuli to facilitate tissue regeneration. We investigate the most recent developments in cancer therapies, including injectable DNA hydrogel for bone regeneration, personalized scaffolds, and dynamic culture models for drug discovery. The study concludes by delineating the remaining obstacles and potential future orientations in the optimization of DNA hydrogel design for the regeneration and reconstruction of tissue. It also addresses strategies for surmounting current challenges and incorporating more sophisticated technologies, thereby facilitating the clinical translation of these innovative hydrogels.

Effects of Polyhydroxybutyrate-co-hydroxyvalerate Microparticle Loading on Rheology, Microstructure, and Processability of Hydrogel-Based Inks for Bioprinted and Moulded Scaffolds

Resorbable microparticles can be added to hydrogel-based biocompatible scaffolds to improve their mechanical characteristics and allow localised drug delivery, which will aid in tissue repair and regeneration. It is well-known that bioprinting is important for producing scaffolds personalised to patients by loading them with their own cells and printing them with specified shapes and dimensions. The question is how the addition of such particles affects the rheological responsiveness of the hydrogels (which is critical during the printing process) as well as mechanical parameters like the elastic modulus. This study tries to answer this question using a specific system: an alginate-gelatine hydrogel containing polyhydroxybutyrate-co-hydroxyvalerate (PHBV) microparticles. Scaffolds were made by bioprinting and moulding incorporating PHBV microspheres (7-12 μm in diameter) into alginate-gelatine inks (4.5 to 9.0% w/v). The microparticles (MP) were predominantly located within the polymeric matrix at concentrations up to 10 mg MP/mL ink. Higher particle concentrations disrupted their spatial distribution. Inks pre-crosslinked with 15 mM calcium and containingMPat concentrations ranging from 0 to 10 mg/mL demonstrated rheological characteristics appropriate for bioprinting, such as solid-like behaviour (G' = 1060-1300 Pa, G″ = 720-930 Pa), yield stresses of 320-400 Pa, and pseudoplastic behaviour (static viscosities of 4000-5600 Pa·s and ~100 Pa·s at bioprinting shear rates). Furthermore, these inks allow high printing quality, assessed through scaffold dimensions, filament widths, and printability (Pr > 0.94). The modulus of elasticity in compression (E) of the scaffolds varied according to the content of MP and the manufacturing technique, with values resembling those of soft tissues (200-600 kPa) and exhibiting a maximum reinforcement effect with 3 mg MP/mL ink (bioprinted E = 273 ± 28 kPa; moulded E = 541 ± 66 kPa). Over the course of six days, the sample's mass and shape remained stable during degradation in simulated body fluid (SBF). Thus, the alginate-gelatine hydrogel loaded with PHBV microspheres inks shows promise for targeted drug delivery in soft tissue bioengineering applications.

Next-generation biopolymer gels: innovations in drug delivery and theranostics

Biopolymers or natural polymers like chitosan, cellulose, alginate, collagen, etc. have gained significant interest recently due to their remarkable tunable properties that make them appropriate for a variety of applications & play a crucial role in everyday life. The features of biopolymers which include biodegradability, biocompatibility, sustainability, affordability, & availability are vital for creating products for use in biomedical fields. Apart from these characteristics, smart or stimuli-responsive biopolymers also show a distinctive property of being susceptible to various factors like pH, temperature, light intensity, & electrical or magnetic fields. The current review would present a brief idea about smart biopolymer gels along with their biomedical applications. The use of smart biopolymers gels as theranostic agents are also discussed in the present review. This review also focuses on the application of biopolymers in the fields of drug delivery, cancer treatment, tissue engineering & wound healing. These areas demonstrate the development and utilization of different types of biopolymers in current biomedical applications.

Improved Mesenchymal Stem Cell Viability in High-Stiffness, Translational Cartilage Matrix Hydrogels

Scaffolds made from cartilage extracellular matrix are promising materials for articular cartilage repair, attributed to their intrinsic bioactivity that may promote chondrogenesis. While several cartilage matrix-based scaffolds have supported chondrogenesis in vitro and/or in vivo, it remains a challenge to balance the biological response (e.g., chondroinductivity) with structural (e.g., robust mechanical performance, >1 MPa in compressive stiffness) and translational (e.g., ease of surgical implantation) considerations. Few studies have evaluated encapsulated cell viability within high-stiffness (>1 MPa) hydrogels. We previously fabricated one formulation of a high-stiffness (>3 MPa) pentenoate-functionalized, solubilized, devitalized cartilage (PSDVC) hydrogel that possessed an injectable, paste-like precursor for easy surgical application. In the current study, the characterization of the PSDVC material was expanded by varying the degree of functionalization (i.e., 0.45-1.09 mmol/g) and amount of crosslinker, dithiothreitol (DTT), to improve the reproducibility of the high compressive moduli and evaluate the viability of encapsulated human bone marrow-derived mesenchymal stem cells (hBMSCs) in high-stiffness cartilage matrix hydrogels. Prior to crosslinking, specific formulations functionalized with 0.80 mmol/g or less of pentenoate groups retained a paste-like precursor rheology. After crosslinking, these formulations produced hydrogels with greater than 1 MPa compressive stiffness. However, hBMSCs encapsulated in PSDVC hydrogels with lower functionalization (i.e., 0.57 mmol/g, no crosslinker) had a higher stiffness (i.e., 1.4 MPa) but the lowest viability of encapsulated hBMSCs (i.e., 5%). The middle PSDVC functionalization (i.e., 0.70 mmol/g) with DTT (i.e., 0.50 mmol thiols/g) demonstrated high cell viability (77%), high mechanical performance (1.65 MPa, 31% failure strain), and translational features (i.e., paste-like precursor, 1.5 min crosslinking time). For future evaluations of PSDVC hydrogels in cartilage repair, a middle functionalization (i.e., 0.70-0.80 mmol/g) with the addition of a crosslinker (i.e., 0.50 mmol thiols/g) had a desirable balance of high mechanical performance (i.e., >1 MPa compressive stiffness), high viability, and paste-like precursor for surgical translation.

Thiol-ene click chemistry: Enabling 3D printing of natural-based inks for biomedical applications

Over the last decade, 3D bioprinting has gained increasing popularity, being a technique capable of producing well-defined tissue-like structures. One of its most groundbreaking features is the ability to create personalized therapies tailored to the specific demands of individual patients. However, challenges including the selection of materials and crosslinking strategies, still need to be addressed to enhance ink characteristics and develop robust biomaterials. Herein, the authors showcase the potential of overcoming these challenges, focusing on the use of versatile, fast, and selective thiol-ene click chemistry to formulate inks for 3D bioprinting. The exploration of natural polymers, specifically proteins and polysaccharides, will be discussed and highlighted, outlining the advantages and disadvantages of this approach. Leveraging advanced thiol-ene click chemistry and natural polymers in the development of 3D printable bioinks may face the current challenges and is envisioned to pave the way towards innovative and personalized biomaterials for biomedical applications.

Effects of Hydroxyapatite Additions on Alginate Gelation Kinetics During Cross-Linking

Alginate hydrogels have gathered significant attention in biomedical engineering due to their remarkable biocompatibility, biodegradability, and ability to encapsulate cells and bioactive molecules, but much less has been reported on the kinetics of gelation. Scarce experimental data are available on cross-linked alginates (AL) with bioactive components. The present study addressed a novel method for defining the crosslinking mechanism using rheological measurements for aqueous mixtures of AL and calcium chloride (CaCl2) with the presence of hydroxyapatite (HAp) as filler particles. The time-dependent crosslinking behaviour of these mixtures was exploited using a plate-plate rheometer, when crosslinking occurs due to calcium ions (Ca2+) binding to the guluronic acid blocks within the AL polymer, forming a stable "egg-box" structure. To reveal the influence of HAp particles as filler on crosslinked sample morphology, after rheological measurement and crosslinking, crosslinked samples were freeze-dried and their morphology was assessed using an optical microscope and SEM. It was found that the addition of HAp particles, which are known to enhance the mechanical properties and biocompatibility of crosslinked AL gels, significantly decreased (usually rapidly) the interaction between the Ca2+ and AL chains. In this research, the physical "shielding" effect of HAp particles on the crosslinking of AL with Ca2+ ions has been observed for the first time, and its crosslinking behaviour was defined using rheological methods. After crosslinking and rheometer measurements, the samples were further evaluated for morphological properties and the observations were correlated with their dewatering properties. While the presence of HAp particles led to a slower crosslinking process and a more uniform development of the rheological parameters, it also led to a more uniform porosity and improved dewatering properties. The observed effects allow for a better understanding of the crosslinking process kinetics, which directly affects the physical and chemical properties of the AL gels. The shielding behaviour (retardation) of filler particles occurs when they physically or chemically block certain components in a mixture, delaying their interaction with other reactants. In hydrogel formulations, filler particles like hydroxyapatite (HAp) can act as barriers, adsorbing onto reactive components or creating physical separation, which slows the reaction rate and allows for controlled gelation or delayed crosslinking. This delayed reactivity is beneficial for precise control over the reaction timing, enabling the better manipulation of material properties such as crosslinking distribution, pore structure, and mechanical stability. In this research, the physical shielding effect of HAp particles was observed through changes in rheological properties during crosslinking and was dependent on the HAp concentration. The addition of HAp also enabled more uniform porosity and improved dewatering properties. The observed effects allow for a better understanding of the crosslinking process kinetics, which directly affects the physical and chemical properties of the AL gels.

PLL-g-HPA Hydrogel Loaded Human Umbilical Cord Mesenchymal Stem Cells Promote Burn Wound Healing in Rat Model by Regulating Inflammation Response

Purpose

Treatment of severe burn wound injury remains a significant clinical challenge as serious infections/complex repair process and irregulating inflammation response. Human umbilical cord mesenchymal stem cells (hUC-MSCs) have a multidirectional differentiation potential and could repair multiple injuries under appropriate conditions. Poly(L-lysine)-graft-4-hydroxyphenylacetic acid (PLL-g-HPA) hydrogel is an enzyme-promoted biodegradable in hydrogel with good water absorption, biocompatibility and anti-bacterial properties. Therefore, the aim of this study was to evaluate the therapeutic effect of hUC-MSCs combined with PLL-g-HPA hydrogel on full thickness burn injury in rat model.

Methods

The PLL-g-HPA hydrogel was developed and characterized by Scanning Electron Microscopy (SEM), Fourier-Transform Infrared Spectroscopy (FTIR), Hydrogen-1 nuclear magnetic resonance (H-NMR). The cytotoxicity to human foreskin fibroblasts (HFF) were assessed by CCK-8 assay and live/dead quantification and antibacterial activity against Escherichia coli and Staphylococcus aureus was also detected by colony forming unit. A full-thickness burn wound injury model in 12 SD rats was established, and the therapeutic effect of PLL-g-HPA hydrogel combined with hUC-MSCs was detected by healing time/Histology/inflammation factor expression level.

Results

The findings from SEM, FTIR, and HFF analyses demonstrated the successful synthesis of PLL-g-HPA hydrogels. These hydrogels exhibited low cytotoxicity at minimal concentrations while maintaining excellent moisture retention and antibacterial properties. Compared to the control group, treatment with PLL-g-HPA hydrogel in conjunction with hUC-MSCs significantly enhanced wound healing, modulated inflammatory responses, and promoted angiogenesis as well as re-epithelialization in rat models.

Conclusion

The PLL-g-HPA hydrogel in conjunction with hUC-MSCs represents a promising therapeutic approach for the management of burn wounds.

Design and characterization of high-performance energetic hydrogels with enhanced mechanical and explosive properties

Polymeric hydrogels, known for their excellent mechanical properties and pre-cross-linking flowability, provide a promising solution for recycling waste propellants, ensuring safety and maintaining explosive performance. This study developed a double cross-linked network energetic hydrogel that effectively combines mechanical strength with explosive capabilities. Using a Ford 4 Cup, temperature data logger, universal testing machine, and detonation performance tests, we examined the impacts of kinematic viscosity, cross-linking time, compressive strength, and explosive properties. The optimal kinematic viscosity for stabilizing hollow glass microspheres (GM) was found to be 129.7 mm2/s. Cross-linking time was negatively correlated with initiator, catalyst levels, and reaction temperature, but positively correlated with retarder content. Compressive strength increased with acrylamide (AM) content and showed an initial rise before decreasing with N,N'-methylenebisacrylamide (MBAA) content and reaction temperature. The maximum compressive strength was achieved with 5% MBAA (of AM mass fraction) at 40 °C. Detonation velocity and steel plate damage decreased with increasing AM content and initially increased then decreased with GM content. A balance of mechanical and explosive properties was achieved with 6% AM and 4% GM, resulting in a detonation velocity of 4536 m/s. This hydrogel shows significant potential for waste munitions management.

Leveraging Blood Components for 3D Printing Applications Through Programmable Ink Engineering Approaches

This study proposes a tunable ink engineering methodology to allow 3D printing processability of highly bioactive but otherwise low-viscous and unprintable blood-derived materials. The hypothesis relies on improving the viscoelasticity and shear thinning behavior of platelet lysates (PL) and albumins (BSA) solutions by covalent coupling, enabling simultaneous extrusion and photocrosslinking upon filament deposition. The available amine groups on proteins (PL and BSA) are exploited for coupling with carboxyl groups present in methacrylated proteins (hPLMA and BSAMA), by leveraging carbodiimide chemistry. This reaction enabled the creation of a pre-gel from these extremely low-viscous materials (≈ 1 Pa), with precise tuning of the reaction, resulting in inks with a range of controlled viscosities and elasticities. Shape-fidelity analysis is performed on 3D-printed multilayered constructs, demonstrating the ability to reach clinically relevant sizes (>2 cm in size). After photocrosslinking, the scaffolds showcased a mechanically robust structure with sustained protein release over time. Bioactivity is evaluated using human adipose-derived stem cells, resulting in increased viability and metabolic activity over time. The herein described research methodology widens the possibilities for the use of low-viscosity materials in 3D printing but also enables the direct application of patient and blood-derived materials in precision medicine.

The impact of mechanical tuning on the printability of decellularized amniotic membrane bioinks for cell-laden bioprinting of soft tissue constructs

Decellularized extracellular matrix (dECM) bioinks hold significant potential in the 3D bioprinting of tissue-engineered constructs (TECs). While 3D bioprinting allows for the creation of custom-designed TECs, the development of bioinks based solely on dAM, without the inclusion of supporting agents or chemical modifications, remains underexplored. In this study, we present the concentration-dependent printability and rheological properties of dAM bioinks, along with an analysis of their in vitro cellular responses. Our findings demonstrate that increasing dAM concentrations, within the range of 1 to 3% w/v, enhances the mechanical moduli of the bioinks, enabling the 3D printing of flat structures with superior shape fidelity. In vitro assays reveal high cell viability across all dAM bioink formulations; however, at 3% w/v, the bioink tends to impede fibroblast proliferation, resulting in round cell morphology. We propose that bioinks containing 2% w/v dAM strike an optimal balance, providing fine-resolved features and a supportive microenvironment for fibroblasts, promoting elongated spindle-like morphology and enhanced proliferation. These results underscore the importance of dAM concentration in regulating the properties and performance of bioinks, particularly regarding cell viability and morphology, for the successful 3D bioprinting of soft tissues.

Topological Data Analysis for Particulate Gels

Soft gels, formed via the self-assembly of particulate materials, exhibit intricate multiscale structures that provide them with flexibility and resilience when subjected to external stresses. This work combines particle simulations and topological data analysis (TDA) to characterize the complex multiscale structure of soft gels. Our TDA analysis focuses on the use of the Euler characteristic, which is an interpretable and computationally scalable topological descriptor that is combined with filtration operations to obtain information on the geometric (local) and topological (global) structure of soft gels. We reduce the topological information obtained with TDA using principal component analysis (PCA) and show that this provides an informative low-dimensional representation of the gel structure. We use the proposed computational framework to investigate the influence of gel preparation (e.g., quench rate, volume fraction) on soft gel structure and to explore dynamic deformations that emerge under oscillatory shear in various response regimes (linear, nonlinear, and flow). Our analysis provides evidence of the existence of hierarchical structures in soft gels, which are not easily identifiable otherwise. Moreover, our analysis reveals direct correlations between topological changes of the gel structure under deformation and mechanical phenomena distinctive of gel materials, such as stiffening and yielding. In summary, we show that TDA facilitates the mathematical representation, quantification, and analysis of soft gel structures, extending traditional network analysis methods to capture both local and global organization.

Bioprinting of Cells, Organoids and Organs-on-a-Chip Together with Hydrogels Improves Structural and Mechanical Cues

The 3D bioprinting technique has made enormous progress in tissue engineering, regenerative medicine and research into diseases such as cancer. Apart from individual cells, a collection of cells, such as organoids, can be printed in combination with various hydrogels. It can be hypothesized that 3D bioprinting will even become a promising tool for mechanobiological analyses of cells, organoids and their matrix environments in highly defined and precisely structured 3D environments, in which the mechanical properties of the cell environment can be individually adjusted. Mechanical obstacles or bead markers can be integrated into bioprinted samples to analyze mechanical deformations and forces within these bioprinted constructs, such as 3D organoids, and to perform biophysical analysis in complex 3D systems, which are still not standard techniques. The review highlights the advances of 3D and 4D printing technologies in integrating mechanobiological cues so that the next step will be a detailed analysis of key future biophysical research directions in organoid generation for the development of disease model systems, tissue regeneration and drug testing from a biophysical perspective. Finally, the review highlights the combination of bioprinted hydrogels, such as pure natural or synthetic hydrogels and mixtures, with organoids, organoid-cell co-cultures, organ-on-a-chip systems and organoid-organ-on-a chip combinations and introduces the use of assembloids to determine the mutual interactions of different cell types and cell-matrix interferences in specific biological and mechanical environments.

Biomaterials-Based Technologies in Skeletal Muscle Tissue Engineering

For many clinically prevalent severe injuries, the inherent regenerative capacity of skeletal muscle remains inadequate. Skeletal muscle tissue engineering (SMTE) seeks to meet this clinical demand. With continuous progress in biomedicine and related technologies including micro/nanotechnology and 3D printing, numerous studies have uncovered various intrinsic mechanisms regulating skeletal muscle regeneration and developed tailored biomaterial systems based on these understandings. Here, the skeletal muscle structure and regeneration process are discussed and the diverse biomaterial systems derived from various technologies are explored in detail. Biomaterials serve not merely as local niches for cell growth, but also as scaffolds endowed with structural or physicochemical properties that provide tissue regenerative cues such as topographical, electrical, and mechanical signals. They can also act as delivery systems for stem cells and bioactive molecules that have been shown as key participants in endogenous repair cascades. To achieve bench-to-bedside translation, the typical effect enabled by biomaterial systems and the potential underlying molecular mechanisms are also summarized. Insights into the roles of biomaterials in SMTE from cellular and molecular perspectives are provided. Finally, perspectives on the advancement of SMTE are provided, for which gene therapy, exosomes, and hybrid biomaterials may hold promise to make important contributions.

3D Bioprinting of Hyaline Cartilage Using Nasal Chondrocytes

Due to the limited self-repair capacity of the hyaline cartilage, the repair of cartilage remains an unsolved clinical problem. Tissue engineering strategy with 3D bioprinting technique has emerged a new insight by providing patient's personalized cartilage grafts using autologous cells for hyaline cartilage repair and regeneration. In this review, we first summarized the intrinsic property of hyaline cartilage in both maxillofacial and orthopedic regions to establish the requirement for 3D bioprinting cartilage tissue. We then reviewed the literature and provided opinion pieces on the selection of bioprinters, bioink materials, and cell sources. This review aims to identify the current challenges for hyaline cartilage bioprinting and the directions for future clinical development in bioprinted hyaline cartilage.

Biomaterials for extrusion-based bioprinting and biomedical applications

Amongst the range of bioprinting technologies currently available, bioprinting by material extrusion is gaining increasing popularity due to accessibility, low cost, and the absence of energy sources, such as lasers, which may significantly damage the cells. New applications of extrusion-based bioprinting are systematically emerging in the biomedical field in relation to tissue and organ fabrication. Extrusion-based bioprinting presents a series of specific challenges in relation to achievable resolutions, accuracy and speed. Resolution and accuracy in particular are of paramount importance for the realization of microstructures (for example, vascularization) within tissues and organs. Another major theme of research is cell survival and functional preservation, as extruded bioinks have cells subjected to considerable shear stresses as they travel through the extrusion apparatus. Here, an overview of the main available extrusion-based printing technologies and related families of bioprinting materials (bioinks) is provided. The main challenges related to achieving resolution and accuracy whilst assuring cell viability and function are discussed in relation to specific application contexts in the field of tissue and organ fabrication.

Moldable Tissue-Sealant Hydrogels Composed of In Situ Cross-Linkable Polyethylene Glycol via Thiol-Michael Addition and Carbomers

Moldable tissue-sealant hydrogels were developed herein by combining the yield stress fluidity of a Carbomer and in situ cross-linking of 3-arm PEG-thiol (PEG-SH) and 4-arm PEG-acrylate (PEG-AC). The Carbomer was mixed with each PEG oligomer to form two aqueous precursors: Carbomer/PEG-SH and Carbomer/PEG-AC. The two hydrogel precursors exhibited sufficient yield stress (>100 Pa) to prevent dripping from their placement on the tissue surface. Moreover, these hydrogel precursors exhibited rapid restructuring when the shear strain was repeatedly changed. These rheological properties contribute to the moldability of these hydrogel precursors. After mixing these two precursors, they were converted from yield-stress fluids to chemically cross-linked hydrogels, Carbomer/PEG hydrogel, via thiol-Michael addition. The gelation time was 5.0 and 11.2 min at 37 and 25 °C, respectively. In addition, the Carbomer/PEG hydrogels exhibited higher cellular viability than the pure Carbomer. They also showed stable adhesiveness and burst pressure resistance to various tissues, such as the skin, stomach, colon, and cecum of pigs. The hydrogels showed excellent tissue sealing in a cecum ligation and puncture model in mice and improved the survival rate due to their tissue adhesiveness and biocompatibility. The Carbomer/PEG hydrogel is a potential biocompatible tissue sealant that surgeons can mold. It was revealed that the combination of in situ cross-linkable PEG oligomers and yield stress fluid such as Carbomer is effective for developing the moldable tissue sealant without dripping of its hydrogel precursors.

Multiprotein collagen/keratin hydrogel promoted myogenesis and angiogenesis of injured skeletal muscles in a mouse model

Volumetric loss is one of the challenging issues in muscle tissue structure that causes functio laesa. Tissue engineering of muscle tissue using suitable hydrogels is an alternative to restoring the physiological properties of the injured area. Here, myogenic properties of type I collagen (0.5%) and keratin (0.5%) were investigated in a mouse model of biceps femoris injury. Using FTIR, gelation time, and rheological analysis, the physicochemical properties of the collagen (Col)/Keratin scaffold were analyzed. Mouse C2C12 myoblast-laden Col/Keratin hydrogels were injected into the injury site and histological examination plus western blotting were performed to measure myogenic potential after 15 days. FTIR indicated an appropriate interaction between keratin and collagen. The blend of Col/Keratin delayed gelation time when compared to the collagen alone group. Rheological analysis revealed decreased stiffening in blended Col/Keratin hydrogel which is favorable for the extrudability of the hydrogel. Transplantation of C2C12 myoblast-laden Col/Keratin hydrogel to injured muscle tissues led to the formation of newly generated myofibers compared to cell-free hydrogel and collagen groups (p < 0.05). In the C2C12 myoblast-laden Col/Keratin group, a low number of CD31+ cells with minimum inflammatory cells was evident. Western blotting indicated the promotion of MyoD in mice that received cell-laden Col/Keratin hydrogel compared to the other groups (p < 0.05). Despite the increase of the myosin cell-laden Col/Keratin hydrogel group, no significant differences were obtained related to other groups (p > 0.05). The blend of Col/Keratin loaded with myoblasts provides a suitable myogenic platform for the alleviation of injured muscle tissue.

Pimobendan controlled release guar gum printlets: Tailoring drug doses for personalised veterinary medicines

Treating chronic heart diseases in dogs is challenging due to variations in mass within and between species. Pimobendan (PBD), a veterinary drug only, is prescribed in specific cases of chronic heart disease in dogs and is available on the market in only a few different doses. Furthermore, the therapy itself is challenging due to the large size of the chewable tablets and the requirement for twice-daily administration. The development of customised and on-demand PBD medicines by three-dimensional (3D) printing has been proposed to circumvent these disadvantages. In this study, we designed controlled-release flavoured printlets containing PBD. We evaluated the use of two natural polymers, guar or xanthan gums, as the main component of the printing inks. Guar gum showed the better rheological behavior and printability by semisolid extrusion. The printlets were produced in three different shapes and sizes to allow dose customisation. Guar gum printlets showed a PBD controlled release profile, regardless of their shape or size. Therefore, we have demonstrated a novel approach for controlling PBD drug release and tailoring the dose by employing a natural polymer to produce 3D-printed tablets. This study represents a significant step towards the development of 3D-printed guar gum controlled-release formulations for veterinary applications.

Evaluation of the printability of agar and hydroxypropyl methylcellulose gels as gummy formulations: Insights from rheological properties

The trial-and-error method currently used to create formulations with excellent printability demands considerable time and resources, primarily due to the increasing number of variables involved. Rheology serves as a relatively rapid and highly beneficial method for assessing materials and evaluating their effectiveness as 3D constructs. However, the data obtained can be overwhelming, especially for users lacking experience in this field. This study examined the rheological properties of formulations of agar, hydroxypropyl methylcellulose, and the model drug caffeine, alongside exploring their printability as gummy formulations. The gels' rheological properties were characterized using oscillatory and rotational experiments. The correlation between these gels' rheological properties and their printability was established, and three clusters were formed based on the rheological properties and printability of the samples using principal component analysis. Furthermore, the printability was predicted using the sample's rheological property that correlated most with printability, the phase angle δ, and the regression models resulted in an accuracy of over 80%. Although these relationships merit confirmation in later studies, this study suggests a quantitative definition of the relationship between printability and one rheological property and can be used for the development of formulations destined for extrusion 3D printing.

In situ polymer gelation in confined flow controls intermittent dynamics

Polymer flows through pores, nozzles and other small channels govern engineered and naturally occurring dynamics in many processes, from 3D printing to oil recovery in the earth's subsurface to a wide variety of biological flows. The crosslinking of polymers can change their material properties dramatically, and it is advantageous to know a priori whether or not crosslinking polymers will lead to clogged channels or cessation of flow. In this study, we investigate the flow of a common biopolymer, alginate, while it undergoes crosslinking by the addition of a crosslinker, calcium, driven through a microfluidic channel at constant flow rate. We map the boundaries defining complete clogging and flow as a function of flow rate, polymer concentration, and crosslinker concentration. Interestingly, the boundaries of the dynamic behavior qualitatively match the thermodynamic jamming phase diagram of attractive colloidal particles. That is, polymer clogging occurs in a region analogous to colloids in a jammed state, while the polymer flows in regions corresponding to colloids in a liquid phase. However, between the dynamic regimes of complete clogging and unrestricted flow, we observe a remarkable phenomenon in which the crosslinked polymer intermittently clogs the channel. This pattern of deposition and removal of a crosslinked gel is simultaneously highly reproducible, long-lasting, and controllable by system parameters. Higher concentrations of polymer and cross-linker result in more frequent ablation, while gels formed at lower component concentrations ablate less frequently. Upon ablation, the eluted gel maintains its shape, resulting in micro-rods several hundred microns long. Our results suggest both rich dynamics of intermittent flows in crosslinking polymers and the ability to control them.

An effective route to the additive manufacturing of a mechanically gradient supramolecular polymer nanocomposite structure

3D Printing techniques are additive methods of fabricating parts directly from computer-aided designs. Whilst the clearest benefit is the realisation of geometrical freedom, multi-material printing allows the introduction of compositional variation and highly tailored product functionality. The paper reports a proof-of-concept additive manufacturing study to deposit a supramolecular polymer and a complementary organic filler to form composites with gradient composition to enable spatial distribution of mechanical properties and functionality by tuning the number of supramolecular interactions. We use a dual-feed extrusion 3D printing process, with feed stocks based on the supramolecular polymer and its organic composite, delivered at ratios predetermined. This allows for production of a graded specimen with varying filler concentration that dictates the mechanical properties. The printed specimen was inspected under dynamic load in a tensile test using digital image correlation to produce full-field deformation maps, which showed clear differences in deformation in regions with varying compositions, corresponding to the designed-in variations. This approach affords a novel method for printing material with graded mechanical properties which are not currently commercially available or easily accessible, however, the method can potentially be directly translated to the generation of biomaterial-based composites featuring gradients of mechanical properties.

Riboflavin mediated UV crosslinking of chitosan-gelatin cryogels for loading of hydrophobic bioactive compounds

Chitosan-gelatin cryogels with good loading capacity of hydrophobic compounds were successfully obtained by UV-induced crosslinking. Using riboflavin as photoinitiator was a suitable alternative to classical carbodiimide crosslinking in obtaining carrier matrices for bioactive hydrophobic compounds. Chitosan had a double role, acting both as a base polymer for the hydrogel network and as co-initiator in riboflavin photo-crosslinking. This co-initiator role of chitosan is due to its electron donor capacity, being well known as a Lewis base type macromolecule. The rheological behaviour of the chitosan-gelatin hydrogel precursor solutions was greatly influenced by riboflavin addition as well as by UV irradiation. As a consequence, the temperature of the sol-gel transition during cooling decreased to 25.5 °C. Compared with classical carbodiimide crosslinking, UV irradiation lead to gels with increased network stability, enhanced elastic behaviour, higher structural strength and almost total stress recovery yield (99 %), the latter indicating self-healing capacity. The cryogels manifested pH responsive swelling, this being highest at close to neutral pH of 7.4. Although hydrophilic in nature, the chitosan-gelatin cryogels crosslinked under the combined effect of riboflavin and UV exposure possess the necessary chemical functionality and morphology that allowed successful embedding of hydrophobic clove essential oil. This was loaded by immersion or fumigation and imparted antioxidant activity to the polymeric matrix.

3D Printing of smart labels with curcumin-loaded soy protein isolate

A two-step method for preparing smart labels that can monitor food freshness through color change is presented. The conventional casting method for such labels is not cost-effective, as it uses organic solvents and requires additional cutting processes. Our method is more eco-friendly and customizable, as it uses water as the sole solvent and 3D printing as the fabrication technique. First, curcumin was encapsulated with soy protein isolate (SPI) by a pH-driven method involving hydrogen bonding and hydrophobic interactions. Subsequently, the SPI-curcumin complex was blended with gelatin to create a printable ink. The ink has suitable rheological properties for extrusion, with a yield stress of 400-600 Pa and a viscosity of 122.93-142.82 Pa·s at the optimal printing temperature. The complex modulus of the ink increases to above 2 × 103 Pa when cooled to 25 °C, indicating rapid gel formation. The application of these smart labels to minced meat demonstrated their ability to reflect its freshness by transitioning from yellow to red. Furthermore, the printability and mechanical properties of the labels can be adjusted by changing the glycerol/water ratio. This innovative approach is a promising solution for producing environmentally friendly and customizable smart labels for food freshness monitoring.

Evaluation of hyaluronic acid-polymacrolactone hydrogels with 3D printing capacity

The implementation of personalized patches, tailored to individual genetic profiles and containing specific amounts of bioactive substances, has the potential to produce a transformative impact within the medical sector. There are several methods of designing scaffolds in the context of personalized medicine, with three-dimensional (3D) printing emerging as a pivotal technique. This innovative approach can be used to construct a wide variety of pharmaceutical dosage forms, characterized by variations in shape, release profile, and drug combinations, allowing precise dose individualization and the incorporation of multiple therapeutic agents. To expand the potential and applicability of personalized medicine, particularly with regards to indomethacin (IND), a drug necessitating individualized dosing, this study proposes the development of new transdermal delivery systems for IND based on hyaluronic acid and a polylactone synthesized within our research group, namely poly(ethylene brasilate-co-squaric acid) (PEBSA). The obtained systems were characterized in terms of their swelling capacity, rheological behavior, and morphological characteristics that highlighted the formation of stable three-dimensional networks. To impart specific shape and geometry to the structures, multi-component systems based on PEBSA, HA, and methacrylate gelatin were obtained. The scaffolds were loaded with IND and subsequently 3D printed. The release capacity of IND and its dependence on the relative ratios of the components comprising the scaffold composition were highlighted. The cytocompatibility studies revealed the successful development of biocompatible and noncytotoxic systems.

Decellularized extracellular matrix and silk fibroin-based hybrid biomaterials: A comprehensive review on fabrication techniques and tissue-specific applications

Biomaterials play a fundamental role in tissue engineering by providing biochemical and physical cues that influence cellular fate and matrix development. Decellularized extracellular matrix (dECM) as a biomaterial is distinguished by its abundant composition of matrix proteins, such as collagen, elastin, fibronectin, and laminin, as well as glycosaminoglycans and proteoglycans. However, the mechanical properties of only dECM-based constructs may not always meet tissue-specific requirements. Recent advancements address this challenge by utilizing hybrid biomaterials that harness the strengths of silk fibroin (SF), which contributes the necessary mechanical properties, while dECM provides essential cellular cues for in vitro studies and tissue regeneration. This review discusses emerging trends in developing such biopolymer blends, aiming to synergistically combine the advantages of SF and dECM through optimal concentrations and desired cross-linking density. We focus on different fabrication techniques and cross-linking methods that have been utilized to fabricate various tissue-engineered hybrid constructs. Furthermore, we survey recent applications of such biomaterials for the regeneration of various tissues, including bone, cartilage, trachea, bladder, vascular graft, heart, skin, liver, and other soft tissues. Finally, the trajectory and prospects of the constructs derived from this blend in the tissue engineering field have been summarized, highlighting their potential for clinical translation.

Rheology in Product Development: An Insight into 3D Printing of Hydrogels and Aerogels

Rheological characterisation plays a crucial role in developing and optimising advanced materials in the form of hydrogels and aerogels, especially if 3D printing technologies are involved. Applications ranging from tissue engineering to environmental remediation require the fine-tuning of such properties. Nonetheless, their complex rheological behaviour presents unique challenges in additive manufacturing. This review outlines the vital rheological parameters that influence the printability of hydrogel and aerogel inks, emphasising the importance of viscosity, yield stress, and viscoelasticity. Furthermore, the article discusses the latest developments in rheological modifiers and printing techniques that enable precise control over material deposition and resolution in 3D printing. By understanding and manipulating the rheological properties of these materials, researchers can explore new possibilities for applications such as biomedicine or nanotechnology. An optimal 3D printing ink requires strong shear-thinning behaviour for smooth extrusion, forming continuous filaments. Favourable thixotropic properties aid viscosity recovery post-printing, and adequate yield stress and G' are crucial for structural integrity, preventing deformation or collapse in printed objects, and ensuring high-fidelity preservation of shapes. This insight into rheology provides tools for the future of material design and manufacturing in the rapidly evolving field of 3D printing of hydrogels and aerogels.

3D-Printed Hydrogel for Diverse Applications: A Review

Hydrogels have emerged as a versatile and promising class of materials in the field of 3D printing, offering unique properties suitable for various applications. This review delves into the intersection of hydrogels and 3D printing, exploring current research, technological advancements, and future directions. It starts with an overview of hydrogel basics, including composition and properties, and details various hydrogel materials used in 3D printing. The review explores diverse 3D printing methods for hydrogels, discussing their advantages and limitations. It emphasizes the integration of 3D-printed hydrogels in biomedical engineering, showcasing its role in tissue engineering, regenerative medicine, and drug delivery. Beyond healthcare, it also examines their applications in the food, cosmetics, and electronics industries. Challenges like resolution limitations and scalability are addressed. The review predicts future trends in material development, printing techniques, and novel applications.

Rise of tissue- and species-specific 3D bioprinting based on decellularized extracellular matrix-derived bioinks and bioresins

Thanks to its natural complexity and functionality, decellularized extracellular matrix (dECM) serves as an excellent foundation for creating highly cell-compatible bioinks and bioresins. This enables the bioprinted cells to thrive in an environment that closely mimics their native ECM composition and offers customizable biomechanical properties. To formulate dECM bioinks and bioresins, one must first pulverize and/or solubilize the dECM into non-crosslinked fragments, which can then be chemically modified as needed. In bioprinting, the solubilized dECM-derived material is typically deposited and/or crosslinked in a layer-by-layer fashion to build 3D hydrogel structures. Since the introduction of the first liver-derived dECM-based bioinks, a wide variety of decellularized tissue have been employed in bioprinting, including kidney, heart, cartilage, and adipose tissue among others. This review aims to summarize the critical steps involved in tissue-derived dECM bioprinting, starting from the decellularization of the ECM to the standardized formulation of bioinks and bioresins, ultimately leading to the reproducible bioprinting of tissue constructs. Notably, this discussion also covers photocrosslinkable dECM bioresins, which are particularly attractive due to their ability to provide precise spatiotemporal control over the gelation in bioprinting. Both in extrusion printing and vat photopolymerization, there is a need for more standardized protocols to fully harness the unique properties of dECM-derived materials. In addition to mammalian tissues, the most recent bioprinting approaches involve the use of microbial extracellular polymeric substances in bioprinting of bacteria. This presents similar challenges as those encountered in mammalian cell printing and represents a fascinating frontier in bioprinting technology.

Development of photoreactive demineralized bone matrix 3D printing colloidal inks for bone tissue engineering

Demineralized bone matrix (DBM) has been widely used clinically for dental, craniofacial and skeletal bone repair, as an osteoinductive and osteoconductive material. 3D printing (3DP) enables the creation of bone tissue engineering scaffolds with complex geometries and porosity. Photoreactive methacryloylated gelatin nanoparticles (GNP-MAs) 3DP inks have been developed, which display gel-like behavior for high print fidelity and are capable of post-printing photocrosslinking for control of scaffold swelling and degradation. Here, novel DBM nanoparticles (DBM-NPs, ∼400 nm) were fabricated and characterized prior to incorporation in 3DP inks. The objectives of this study were to determine how these DBM-NPs would influence the printability of composite colloidal 3DP inks, assess the impact of ultraviolet (UV) crosslinking on 3DP scaffold swelling and degradation and evaluate the osteogenic potential of DBM-NP-containing composite colloidal scaffolds. The addition of methacryloylated DBM-NPs (DBM-NP-MAs) to composite colloidal inks (100:0, 95:5 and 75:25 GNP-MA:DBM-NP-MA) did not significantly impact the rheological properties associated with printability, such as viscosity and shear recovery or photocrosslinking. UV crosslinking with a UV dosage of 3 J/cm2 directly impacted the rate of 3DP scaffold swelling for all GNP-MA:DBM-NP-MA ratios with an ∼40% greater increase in scaffold area and pore area in uncrosslinked versus photocrosslinked scaffolds over 21 days in phosphate-buffered saline (PBS). Likewise, degradation (hydrolytic and enzymatic) over 21 days for all DBM-NP-MA content groups was significantly decreased, ∼45% less in PBS and collagenase-containing PBS, in UV-crosslinked versus uncrosslinked groups. The incorporation of DBM-NP-MAs into scaffolds decreased mass loss compared to GNP-MA-only scaffolds during collagenase degradation. An in vitro osteogenic study with bone marrow-derived mesenchymal stem cells demonstrated osteoconductive properties of 3DP scaffolds for the DBM-NP-MA contents examined. The creation of photoreactive DBM-NP-MAs and their application in 3DP provide a platform for the development of ECM-derived colloidal materials and tailored control of biochemical cue presentation with broad tissue engineering applications.

Rheological and physicochemical properties of Spirulina platensis residues-based inks for extrusion 3D food printing

Novel food matrices (such as microalgae, plants, fungi, and microbial proteins) with high protein content and biological value, good amino acid profile, and functionality have been explored. Phycocyanin and active polysaccharides extracted from Spirulina platensis are used as food additives, treatment of colitis, as well as obesity prevention. However, most of the remaining Spirulina platensis residues are mainly used as fish feed at present. 3D food printing is one of the promising development techniques used in the food industry. The aim of this study was to develop a novel 3D printing material of Spirulina platensis residues with shear thinning characteristics, high viscosity and rapid recovery. The effects of moisture content and pretreatment method on the rheological properties of Spirulina platensis residues were clarified. Scanning electron microscopy was used to observe the microstructure and texture profile analysis was used to determine the texture characteristics of Spirulina platensis residues, rheology was used to determine the key 3D printing factors such as viscosity and modulus of Spirulina platensis residues. More importantly, the printing process could be realized under ambient conditions. The development of microalgae residue ink promoted the high-value and comprehensive utilization of microalgae, and also broadened the application of microalgae in the food field.

Loquat seed starch - Emerging source of non-conventional starch: Structure, properties, and novel applications

Recently, non-conventional sources of starch have attracted attention due to their potential to provide cost-effective alternatives to traditional starch. Among non-conventional starches, loquat (Eriobotrya japonica) seed starch is an emerging source of starch consisting of the amount of starch (nearly 20 %). Due to its unique structure, functional properties, and novel applications, it could be utilized as a potential ingredient. Interestingly, this starch has similar properties as commercial starches including high amylose content, small granule size, and high viscosity and heat stability, making it an attractive option for various food applications. Therefore, this review mainly covers the fundamental understanding of the valorization of loquat seeds by extracting the starch using different isolation methods, with preferable structural, morphological, and functional properties. Different isolation and modification methods (wet milling, acid, neutral and alkaline) are effectively used to obtain higher amounts of starch are revealed. Moreover, insight into various analytical techniques including scanning electron microscopy, differential scanning calorimetry, and X-ray diffraction used to characterize the molecular structure of the starch are discussed. In addition, the effect of shear rate and temperature on rheological attributes with solubility index, swelling power, and color is revealed. Besides, this starch contains bioactive compounds that have shown a positive impact on the enhancement of the shelf-life of the fruits. Overall, loquat seed starches have the potential to provide sustainable and cost-effective alternatives to traditional starch sources and can lead to novel applications in the food industry. Further research is needed to optimize processing techniques and develop value-added products that can be produced at a large scale. However, there is relatively limited published scientific evidence on the structural and morphological characteristics of loquat seed starch. Thus, in this review, we focused on different isolation techniques of loquat seed starch, its structural and functional characteristics, along with potential applications.

Characterization and Validation of a New 3D Printing Ink for Reducing Therapeutic Gap in Pediatrics through Individualized Medicines

3D printing technology can be used to develop individualized medicines in hospitals and pharmacies, allowing a high degree of personalization and the possibility to adjust the dose of the API based on the quantity of material extruded. The main goal of incorporating this technology is to have a stock of API-load print cartridges that could be used at different storage times and for different patients. However, it is necessary to study the extrudability, stability, and buildability of these print cartridges during storage time. A paste-like formulation containing hydrochlorothiazide as a model drug was prepared and distributed in five print cartridges, each of which was studied for different storage times (0 h-72 h) and conditions, for repeated use on different days. For each print cartridge, an extrudability analysis was performed, and subsequently, 100 unit forms of 10 mg hydrochlorothiazide were printed. Finally, various dosage units containing different doses were printed, taking into account the optimized printing parameters based on the results of the extrudability analysis carried out previously. An appropriate methodology for the rapid development of appropriate SSE 3DP inks for pediatrics was established and evaluated. The extrudability analysis and several parameters allowed the detection of changes in the mechanical behavior of the printing inks, the pressure interval of the steady flow, and the selection of the volume of ink to be extruded to obtain each of the required doses. The print cartridges were stable for up to 72 h after processing, and orodispersible printlets containing 6 mg to 24 mg of hydrochlorothiazide can be produced using the same print cartridge and during the same printing process with guaranteed content and chemical stability. The proposed workflow for the development of new printing inks containing APIs will allow the optimization of feedstock material and human resources in pharmacy or hospital pharmacy services, thus speeding up their development and reducing costs.

3D and 4D Bioprinting Technologies: A Game Changer for the Biomedical Sector?

Bioprinting is an innovative and emerging technology of additive manufacturing (AM) and has revolutionized the biomedical sector by printing three-dimensional (3D) cell-laden constructs in a precise and controlled manner for numerous clinical applications. This approach uses biomaterials and varying types of cells to print constructs for tissue regeneration, e.g., cardiac, bone, corneal, cartilage, neural, and skin. Furthermore, bioprinting technology helps to develop drug delivery and wound healing systems, bio-actuators, bio-robotics, and bio-sensors. More recently, the development of four-dimensional (4D) bioprinting technology and stimuli-responsive materials has transformed the biomedical sector with numerous innovations and revolutions. This issue also leads to the exponential growth of the bioprinting market, with a value over billions of dollars. The present study reviews the concepts and developments of 3D and 4D bioprinting technologies, surveys the applications of these technologies in the biomedical sector, and discusses their potential research topics for future works. It is also urged that collaborative and valiant efforts from clinicians, engineers, scientists, and regulatory bodies are needed for translating this technology into the biomedical, pharmaceutical, and healthcare systems.

Rheology as a Tool for Fine-Tuning the Properties of Printable Bioinspired Gels

Over the last decade, efforts have been oriented toward the development of suitable gels for 3D printing, with controlled morphology and shear-thinning behavior in well-defined conditions. As a multidisciplinary approach to the fabrication of complex biomaterials, 3D bioprinting combines cells and biocompatible materials, which are subsequently printed in specific shapes to generate 3D structures for regenerative medicine or tissue engineering. A major interest is devoted to the printing of biomimetic materials with structural fidelity after their fabrication. Among some requirements imposed for bioinks, such as biocompatibility, nontoxicity, and the possibility to be sterilized, the nondamaging processability represents a critical issue for the stability and functioning of the 3D constructs. The major challenges in the field of printable gels are to mimic at different length scales the structures existing in nature and to reproduce the functions of the biological systems. Thus, a careful investigation of the rheological characteristics allows a fine-tuning of the material properties that are manufactured for targeted applications. The fluid-like or solid-like behavior of materials in conditions similar to those encountered in additive manufacturing can be monitored through the viscoelastic parameters determined in different shear conditions. The network strength, shear-thinning, yield point, and thixotropy govern bioprintability. An assessment of these rheological features provides significant insights for the design and characterization of printable gels. This review focuses on the rheological properties of printable bioinspired gels as a survey of cutting-edge research toward developing printed materials for additive manufacturing.

Comparison of a Thiolated Demineralized Bone Matrix Hydrogel to a Clinical Product Control for Regeneration of Large Sheep Cranial Defects

Regeneration of calvarial bone remains a major challenge in the clinic as available options do not sufficiently regenerate bone in larger defect sizes. Calvarial bone regeneration cases involving secondary medical conditions, such as brain herniation during traumatic brain injury (TBI) treatment, further exacerbate treatment options. Hydrogels are well-positioned for severe TBI treatment, given their innate flexibility and potential for bone regeneration to treat TBI in a single-stage surgery. The current study evaluated a photocrosslinking pentenoate-modified hyaluronic acid polymer with thiolated demineralized bone matrix (i.e., TDBM hydrogel) capable of forming a completely interconnected hydrogel matrix for calvarial bone regeneration. The TDBM hydrogel demonstrated a setting time of 120 s, working time of 3 to 7 days, negligible change in setting temperature, physiological setting pH, and negligible cytotoxicity, illustrating suitable performance for in vivo application. Side-by-side ovine calvarial bone defects (19 mm diameter) were employed to compare the TDBM hydrogel to the standard-of-care control material DBX®. After 16 weeks, the TDBM hydrogel had comparable healing to DBX® as demonstrated by mechanical push-out testing (~800 N) and histology. Although DBX® had 59% greater new bone volume compared to the TDBM hydrogel via micro-computed tomography, both demonstrated minimal bone regeneration overall (15 to 25% of defect volume). The current work presents a method for comparing the regenerative potential of new materials to clinical products using a side-by-side cranial bone defect model. Comparison of novel biomaterials to a clinical product control (i.e., standard-of-care) provides an important baseline for successful regeneration and potential for clinical translation.

High-stiffness, fast-crosslinking, cartilage matrix bioinks

Scaffolds derived from cartilage extracellular matrix may contain intrinsic chondroinductivity and have promise for cartilage regeneration. Cartilage is typically ground into devitalized particles (DVC) and several groups have pioneered innovative methods to rebuild the DVC into a new scaffold. However, challenges remain regarding the fluid and solid biomechanics of cartilage-based scaffolds in achieving 1) high mechanical performance akin to native cartilage and 2) easy surgical delivery/retention. Fortunately, photocrosslinking bioinks may benefit clinical translation: paste-like/injectable precursor rheology facilitates surgical placement, and in situ photocrosslinking enables material retention within any size/shape of defect. While solubilized DVC has been modified with methacryloyls (MeSDVC), MeSDVC is limited by slow crosslinking times (e.g., 5-10 min). Therefore, in the current study, we fabricated a pentenoate-modified SDVC (PSDVC), to enable a faster crosslinking reaction via a thiol-ene click chemistry. The crosslinking time of the PSDVC was faster (∼1.7 min) than MeSDVC (∼4 min). We characterized the solid and fluid mechanics/printabilities of PSDVC, pentenoate-modified hyaluronic acid (PHA), and the PHA or PSDVC with added DVC particles. While the addition of DVC particles enhanced the printed shape fidelity of PHA or PSDVC, the increased clogging decreased the ease of printing and cell viability after bioprinting, and future refinement is needed for DVC-containing bioinks. However, the PSDVC alone had a paste-like rheology/good bioprintability prior to crosslinking, the fastest crosslinking time (i.e., 1.7 min), and the highest compressive modulus (i.e., 3.12 ± 0.41 MPa) after crosslinking. Overall, the PSDVC may have future potential as a translational material for cartilage repair.

Sequential Cross-linking of Gallic Acid-Functionalized GelMA-Based Bioinks with Enhanced Printability for Extrusion-Based 3D Bioprinting

The printability of a photocross-linkable methacrylated gelatin (GelMA) bioink with an extrusion-based 3D bioprinter is highly affected by the polymer concentration and printing temperature. In this work, we developed a gallic acid (GA)-functionalized GelMA ink to improve the printability at room and physiological temperatures and to enable tissue adhesion and antioxidant properties. We introduced a sequential cross-linking approach using catechol-Fe³⁺ chelation, followed by photocross-linking. The results show that the ink formulation with 0.5% (w/v) Fe³⁺ in GelMA (30% modification) with 10% GA (GelMA30GA-5Fe) provided the optimum printability, shape fidelity, and structural integrity. The dual network inside the printed constructs significantly enhanced the viscoelastic properties. Printed cylinders were evaluated for their printing accuracy. The printed structures of GelMA30GA-5Fe provided high stability in physiological conditions over a month. In addition, the optimized ink also offered good tissue adhesion and antioxidant property. This catechol-based sequential cross-linking method could be adopted for the fabrication of other single-polymer bioinks.

Tissues and organ printing: An evolution of technology and materials

Since its beginnings, three-dimensional printing (3DP) technology has been successful because of ongoing advances in operating principles, the range of materials and cost-saving measures. However, the 3DP technological progressions in the biomedical sector have majorly taken place in the last decade after the evolution of novel 3DP systems, generally categorised as bioprinters and biomaterials to provide a replacement, transplantation or regeneration of the damaged organs and tissue constructs of the human body. There is now substantial scientific literature accessible to support the benefits of digital healthcare procedures with the help of bioprinters. It is of the highest significance to know the fundamental principles of the available printers and the compatibility of biomaterials as their feedstock, notwithstanding the huge potential of bioprinting systems to manufacture organs and other human body components. This paper provides a precise and helpful reading of the different categories of bioprinters, suitable biomaterials, numerical simulations and modelling and examples of much acknowledged clinical practices. The paper will also cite the prominent issues that still have not received desired solutions. Overall, the article will be of great use for all the professionals, scholars and engineers concerned with the 3DP, bioprinting and biomaterials.