Occurrence of perfluorooctane sulfonate (PFOS) and perfluorooctanoate (PFOA) in N.E. Spanish surface waters and their removal in a drinking water treatment plant that combines conventional and advanced treatments in parallel lines

Perfluorooctanoic acid-contaminated wastewater treatment by forward osmosis: Performance analysis

Perfluorooctanoic acid (PFOA) is a persistent compound, raising considerable global apprehension due to its resistance to breakdown and detrimental impacts on human health and aquatic environments. Pressure-driven membrane technologies treating PFAS-contaminated water are expensive and prone to fouling. This study presented a parametric investigation of the effectiveness of cellulose triacetate membrane in the forward osmosis (FO) membrane for removing PFOA from an aqueous solution. The study examined the influence of membrane orientation modes, feed pH, draw solution composition and concentration, and PFOA concentration on the performance of FO. The experimental results demonstrated that PFOA rejection was 99 % with MgCl2 and slightly >98 % with NaCl draw solutions due to the mechanism of PFOA binding to the membrane surface through Mg2+ ions. This finding highlights the crucial role of the draw solution's composition in PFOA treatment. Laboratory results revealed that membrane rejection of PFOA was 99 % at neutral and acidic pH levels but decreased to 95 % in an alkaline solution at pH 9. The decrease in membrane rejection is attributed to the dissociation of the membrane's functional groups, consequently causing pore swelling. The results were confirmed by calculating the average pore radius of the CTA membrane, which increased from 27.94 nm at pH 5 to 30.70 nm at pH 9. Also, variations in the PFOA concentration from 5 to 100 mg/L did not significantly impact the membrane rejection, indicating the process's capability to handle a wide range of PFOA concentrations. When seawater was the draw solution, the FO membrane rejected 99 % of PFOA concentrations ranging from 5 mg/L to 100 mg/L. The CTA FO treating PFOA-contaminated wastewater from soil remediation achieved a 90 % recovery rate and water flux recovery of 96.5 % after cleaning with DI water at 40 °C, followed by osmotic backwash. The results suggest the potential of using abundant and cost-effective natural solutions in the FO process, all without evident membrane fouling.

Non-target and target screening and risk assessment of per- and polyfluoroalkyl substances in textile wastewater and receiving river

Textile industry uses varieties of chemicals including per- and polyfluoroalkyl substances (PFAS). PFAS are known to be persistent and incompletely removed in wastewater treatment plants (WWTPs). So far, little is known about what types of PFAS are used in the textile industry and their potential risks. Here we investigated PFAS in two WWTPs and a receiving river of a textile industrial park in Guangxi, China, by using both target and non-target analyses over a two-year period. The target analysis identified 11 specific PFAS, while the non-target analysis revealed a list of 648 different PFAS, including both legacy and emerging substances. Notably, perfluorooctanoic acid (PFOA) was still the most prevalent compound detected. Of particular concern was the finding that the investigated WWTPs, which employs an A/O (Anaerobic/Aerobic) process, exhibited a poor removal efficiency for PFAS. The average removal rate was only 22.0 %, indicating that the current treatment processes are inadequate in effectively mitigating PFAS contamination. Correlation analysis further highlighted the potential for PFAS to be transported from WWTPs to the receiving river, revealing a significant and strong positive correlation between the PFAS in the WWTP effluent and those of the river. Perfluorooctanesulfonic acid (PFOS) and two emerging PFAS (DTXSID30240816 and DTXSID90240817) were identified to have high ecological risks in the receiving river. Notably, these two emerging PFAS are homologues, and their presence in WWTPs has been poorly reported. The findings highlight the wide use and persistence of PFAS in current textile WWTPs, indicating potential long term risks to the receiving environment.

Separation of Perfluorooctanoic Acid from Water Using Meso- and Macroporous Syndiotactic Polystyrene Gels

Per- and polyfluoroalkyl substances are an emerging class of contaminants that are environmentally persistent, bioaccumulative, and noxious to human health. Among these, perfluorooctanoic acid (PFOA) molecules are widely found in ground and surface water sources. A novel high surface area, meso- and macroporous syndiotactic polystyrene (sPS) wet gel is used in this work as the adsorbent of PFOA molecules from water at environmentally relevant PFOA concentrations (≤1 μg/L) and cleanse water to below the U.S. EPA's 2023 health advisory limit of 4 parts per trillion (ppt). The sigmoidal shape of the PFOA adsorption isotherm indicates a two-step adsorption mechanism attributed to the strong affinity of PFOA molecules for the sPS surface and molecular aggregation at solid-liquid interfaces or within the pores of the sPS wet gel. The adsorption kinetics and the effects of sPS wet gel porosity, pore size, and pore volume on the removal efficiency are reported. The adsorption kinetics is seen to be strongly dependent on pore size and pore volume.

Evidence on the genotoxic and ecotoxic effects of PFOA, PFOS and their mixture on human lymphocytes and bacteria

Considering that the PFOA and PFOS are widely spread chemicals with harmful effects in human and environmental health as well as the increasing interest of the scientific community in the implications that might present especially when they co-exist, this study aims to assess their harmful impacts, both individually and as a mixture on human lymphocytes and aquatic microorganisms. The cytokinesis-block micronucleus (CBMN) assay was used to examine their potential for cytotoxicity and genotoxicity towards human cells, and Microtox assay using Aliivibrio fischeri assay was used to estimate the environmental risk. Regarding the human lymphocytes, the tested concentrations ranged between 250 and 1000 μg L-1, for all cases. PFOA increased slightly the frequency of micronuclei (MN) but without statistical significance. In the case of PFOS, our results showed a dose-dependent increase in the frequency of micronuclei which showed a statistically significant difference (p < 0.001) at 1000 μg L-1, which is the highest studied concentration. Regarding the CBPI index, statistically significant (p < 0.05, p < 0.01, and p < 0.001 respectively) differences were observed at all studied concentrations of PFOS, compared to the control. The mixture was found to be more cytotoxic and genotoxic than the individual tested compounds, causing a higher decrease at the CBPI index even in lower concentrations and increase at the MN frequencies. Aliivibrio fischeri was exposed to various concentrations in the range of 0.5 μg L-1- 20 mg L-1, for 5 and 15 min and significant increase in the inhibition percentage at the highest tested concentration of their mixture after 15 min was observed.

Emerging and legacy per- and polyfluoroalkyl substances (PFAS) in fluorochemical wastewater along full-scale treatment processes: Source, fate, and ecological risk

The increasing applications of emerging per- and polyfluoroalkyl substances (PFAS) have raised global concern. However, the release of emerging PFAS from the fluorochemical industry remains unclear. Herein, the occurrence of 48 emerging and legacy PFAS in wastewater from 10 fluorochemical manufacturers and mass flows of PFAS in a centralized wastewater treatment plant were investigated. Their distribution and ecological risk in neighboring riverine water were also evaluated. In wastewater from fluorochemical manufacturers, PFAS concentrations were in the range of 14,700-5200,000 ng/L and 2 H,2 H-perfluorooctanoic acid (6:2 FTCA), perfluorooctanoic acid (PFOA), N-ethyl perfluorooctane sulfonamide (N-EtFOSA), and 1 H,1 H,2 H,2 H-perfluorodecanesulfonate (8:2 FTS) were the major PFAS detected. Several PFAS displayed increased mass flows after wastewater treatment, especially PFOA and 6:2 FTCA. The mass flows of PFAS increased from - 20% to 233% after the activated sludge system but decreased by only 0-13% after the activated carbon filtration. In riverine water, PFAS concentrations were in the range of 5900-39,100 ng/L and 6:2 FTCA, 1 H,1 H,2 H,2 H-perfluorodecyl phosphate monoester (8:2 monoPAP), 1 H,1 H,2 H,2 H-perfluorooctyl phosphate monoester (6:2 monoPAP), PFOA, and perfluorohexanoic acid (PFHxA) were the major PFAS detected. PFOA and 6:2 FTCA exhibited comparable hazard quotients for ecological risk. Current wastewater treatment processes cannot fully remove various PFAS discharged by fluorochemical manufacturers, and further investigations on their risk are needed for better chemical management.

Current state of knowledge of environmental occurrence, toxic effects, and advanced treatment of PFOS and PFOA

Per- and polyfluoroalkyl substances (PFAS) are anthropogenic synthetic compounds, with high chemical and thermal stability and a persistent, stable and bioaccumulative nature that renders them a potential hazard for the environment, its organisms, and humans alike. Perfluorooctane sulfonic acid (PFOS) and Perfluorooctanoic acid (PFOA) are the most well-known substances of this category and even though they are phased out from production they are still highly detectable in several environmental matrices. As a result, they have been spread globally in water sources, soil and biota exerting toxic and detrimental effects. Therefore, up and coming technologies, namely advanced oxidation processes (AOPs) and advanced reduction processes (ARPs) are being tested for their implementation in the degradation of these pollutants. Thus, the present review compiles the current knowledge on the occurrence of PFOS and PFOA in the environment, the various toxic effects they have induced in different organisms as well as the ability of AOPs and ARPs to diminish and/or eliminate them from the environment.

Evaluation of commercial nanofiltration and reverse osmosis membrane filtration to remove per-and polyfluoroalkyl substances (PFAS): Effects of transmembrane pressures and water matrices

Perfluoroalkyl and polyfluoroalkyl substances (PFASs) are now widely found in aquatic ecosystems, including sources of drinking water and portable water, due to their increasing prevalence. Among different PFAS treatment or separation technologies, nanofiltration (NF) and reverse osmosis (RO) both yield high rejection efficiencies (>95%) of diverse PFAS in water; however, both technologies are affected by many intrinsic and extrinsic factors. This study evaluated the rejection of PFAS of different carbon chain length (e.g., PFOA and PFBA) by two commercial RO and NF membranes under different operational conditions (e.g., applied pressure and initial PFAS concentration) and feed solution matrixes, such as pH (4-10), salinity (0- to 1000-mM NaCl), and organic matters (0-10 mM). We further performed principal component analysis (PCA) to demonstrate the interrelationships of molecular weight (213-499 g·mol-1 ), membrane characteristics (RO or NF), feed water matrices, and operational conditions on PFAS rejection. Our results confirmed that size exclusion is a primary mechanism of PFAS rejection by RO and NF, as well as the fact that electrostatic interactions are important when PFAS molecules have sizes less than the NF membrane pores. PRACTITIONER POINTS: Two commercial RO and NF membranes were both evaluated to remove 10 different PFAS. High transmembrane pressures facilitated permeate recovery and PFAS rejection by RO. Electrostatic repulsion and pore size exclusion are dominant rejection mechanisms for PFAS removal. pH, ionic strength, and organic matters affected PFAS rejection. Mechanisms of PFAS rejection with RO/NF membranes were explained by PCA analysis.

Insights to estimate exposure to regulated and non-regulated disinfection by-products in drinking water

BACKGROUND

Knowledge about human exposure and health effects associated with non-routinely monitored disinfection by-products (DBPs) in drinking water is sparse.

OBJECTIVE

To provide insights to estimate exposure to regulated and non-regulated DBPs in drinking water.

METHODS

We collected tap water from homes (N = 42), bottled water (N = 10), filtered tap water with domestic activated carbon jars (N = 6) and reverse osmosis (N = 5), and urine (N = 39) samples of participants from Barcelona, Spain. We analyzed 11 haloacetic acids (HAAs), 4 trihalomethanes (THMs), 4 haloacetonitriles (HANs), 2 haloketones, chlorate, chlorite, and trichloronitromethane in water and HAAs in urine samples. Personal information on water intake and socio-demographics was ascertained in the study population (N = 39) through questionnaires. Statistical models were developed based on THMs as explanatory variables using multivariate linear regression and machine learning techniques to predict non-regulated DBPs.

RESULTS

Chlorate, THMs, HAAs, and HANs were quantified in 98-100% tap water samples with median concentration of 214, 42, 18, and 3.2 μg/L, respectively. Multivariate linear regression models had similar or higher goodness of fit (R2) compared to machine learning models. Multivariate linear models for dichloro-, trichloro-, and bromodichloroacetic acid, dichloroacetonitrile, bromochloroacetonitrile, dibromoacetonitrile, trichloropropnanone, and chlorite showed good predictive ability (R2 = 0.8-0.9) as 80-90% of total variance could be explained by THM concentrations. Activated carbon filters reduced DBP concentrations to a variable extent (27-80%), and reverse osmosis reduced DBP concentrations ≥98%. Only chlorate was detected in bottled water samples (N = 3), with median = 13.0 µg/L. Creatinine-adjusted trichloroacetic acid was the most frequently detected HAA in urine samples (69.2%), and moderately correlated with estimated drinking water intake (r = 0.48).

SIGNIFICANCE

Findings provide valuable insights for DBP exposure assessment in epidemiological studies. Validation of predictive models in a larger number of samples and replication in different settings is warranted.

IMPACT STATEMENT

Our study focused on assessing and describing the occurrence of several classes of DBPs in drinking water and developing exposure models of good predictive ability for non-regulated DBPs.

Assessing the persistence, mobility and toxicity of emerging organic contaminants in Croatian karst springs used for drinking water supply

Emerging organic contaminants (EOCs) are a vast group of often (very)persistent, (very)mobile and toxic (PMT/vPvM) substances that are continuously released worldwide, posing environmental and human health risks. Research on occurrence and behavior of EOCs in karst is in its infancy, thus policy measures and legislative control of these compounds in groundwater are still lacking. The Dinaric karst aquifers are an essential source of drinking water for almost half of Croatia's territory. Intense karstification, complex heterogeneous characteristics, and high fracture-cavernous porosity result in rapid, far-reaching groundwater flow and large karst springs, but also high intrinsic vulnerability due to low contaminant attenuation. To prioritize future monitoring and establish appropriate thresholds for EOCs detected in Croatian karst drinking water resources, in silico tools based on quantitative structure-activity relationships were used in PBT (persistence, bioaccumulation, and toxicity) and PMT/vPvM analyzes, while toxicological assessment helped identify potential threats to human health. In 33 samples collected during two sampling campaigns in 2019 at 16 karst springs and one lake used for water supply, we detected 65 compounds (EOCs and some legacy chemicals), of which 7 were classified as potentially PBT or vPvB compounds (PFOS, PFHxS, PFHpA, PFOA, PFNA, boscalid, and azoxystrobin), while only 2 compounds were assessed as not PMT/vPvM. This finding underlines that most of detected EOCs potentially endanger karst (ground)water ecosystems and important drinking water sources in Croatia. Comparison of maximum concentrations with existing or derived drinking water guideline values revealed how 2 of 65 detected compounds represent a potential risk to human health at lifelong exposure (sulfadiazine and hydrochlorothiazide), while 5 chemicals warrant additional human health impacts studies and groundwater monitoring. Although most compounds do not individually pose a significant risk to human health at current environmental levels, their potential synergistic and long-term effects remain unknown.

Chemical Tailoring of β-Cyclodextrin-Graphene Oxide for Enhanced Per- and Polyfluoroalkyl Substances (PFAS) Adsorption from Drinking Water

We report on the synthesis of β-cyclodextrin (βCD) modified graphene oxide (GO) nanosheets, having different sized alkyl linkers (GO-Cn -βCD) and their exploitation as sorbent of per- and polyfluoroalkyl substances (PFAS) from drinking water. βCD were functionalized with a pending amino group, and the resulting precursors grafted to GO nanosheets by epoxide ring opening reaction. Loading of βCD units in the range 12 %-36 % was estimated by combined XPS and elemental analysis. Adsorption tests on perfluorobutanoic acid (PFBA), a particularly persistent PFAS selected as case study, revealed a strong influence of the alkyl linker length on the adsorption efficiency, with the hexyl linker derivative GO-C6 -βCD outperforming both pristine GO and granular activated carbon (GAC), the standard sorbent benchmark. Molecular dynamic simulations ascribed this evidence to the favorable orientation of the βCD unit on the surface of GO which enables a strong contaminant molecules retention.

Comparative study of per- and polyfluoroalkyl substances (PFAS) removal from landfill leachate

Landfill leachate is one of the major point sources of per- and polyfluoroalkyl substances (PFAS) pollution. In this study, powdered activated carbon (PAC), granular activated carbon (GAC), anion exchange resin (AIX), nanofiltration (NF), ozonation, and foam fractionation were tested for treatment of the same leachate. These methods were compared in terms of PFAS removal efficiencies and treatment cost. More than 75% removal of long-chain PFAS (6-9 CF2) could be achieved with all the studied methods, though with high resource consumption. It was demonstrated that PFAS breakthrough was up to 27 times faster when the leachate was treated with GAC and AIX compared to groundwater treatment. Nanofiltration was the only method which could be practically applied for removal of PFAS with the shortest fluorinated carbon chain (3-4 CF2). Foam fractionation and AIX offered the most economical treatment, with an estimated cost of < 1 €/m3 for PFOS and PFOA reduction to ≥ 90%. The cost of treatment was shown to increase exponentially if the goal of > 60% ΣPFAS11 removal was applied. It was also discussed that composite parameters that include expected toxicity of different PFAS, such as ΣPFOAeq, should be used to obtain a cost-efficient reduction of PFAS-induced water toxicity.

Coexisting ions and long-chain per- and polyfluoroalkyl substances (PFAS) inhibit the adsorption of short-chain PFAS by granular activated carbon

We assessed the competitive adsorption between long-chain and short-chain PFAS and the impact of coexisting ions to understand the mechanisms leading to the early breakthrough of short-chain PFAS from granular activated carbon (GAC) filters. Three pairs of short-chain and long-chain PFAS representing different functional groups were studied using GAC (Filtrasorb 400) in batch systems. In bisolute systems, the presence of long-chain PFAS decreased the adsorption of short-chain PFAS by 30-50% compared to their single solute adsorption capacity (0.22-0.31 mmol/g). In contrast to the partial decrease observed in bisolute systems, the addition of long-chain PFAS to GAC pre-equilibrated with short-chain PFAS completely desorbed all short-chain PFAS from GAC. This suggested that the outermost adsorption sites on GAC were preferentially occupied by short-chain PFAS in the absence of competition but were prone to displacement by long-chain PFAS. The presence of inorganic/organic ions inhibited the adsorption of short-chain PFAS (up to 60%) but had little to no impact on long-chain PFAS, with the inhibitory trend inversely correlated with Kow values. Study results indicated that the displacement of short-chain PFAS by long-chain PFAS and charge neutralization are important mechanisms contributing to the early breakthrough of short-chain PFAS from GAC systems.

Toward systematic understanding of adsorptive removal of legacy and emerging per-and polyfluoroalkyl substances (PFASs) by various activated carbons (ACs)

Per-and polyfluoroalkyl substances (PFASs) have received great attention due to their persistence, bioaccumulation and toxicity. Various activated carbons (ACs) exhibit wide variability in adsorptive performance towards PFASs. In order to gain a systematic understanding of adsorptive removal of legacy and emerging PFASs by ACs, the adsorption of ten PFASs on various ACs was comprehensively investigated. Results showed that granular activated carbon-1 (GAC-1) and powdered activated carbon-1 (PAC-1) removed more than 90% of all target PFASs. Particle size, surface charge, and micropores quantity of ACs were closely related to their performance for PFASs removal. Electrostatic interaction, hydrophobic interaction, surface complexation and hydrogen bonding were the adsorption mechanisms, with hydrophobic interaction being the predominant adsorptive force. Physical and chemical adsorption were both involved in PFAS adsorption. The removal rates of PFASs by GAC-1 decreased from 93%-100% to 15%-66% in the presence of 5 mg/L fulvic acid (FA). GAC was able to remove more PFASs under acidic medium, whereas PAC removed hydrophobic PFASs better under the neutral medium. The removal rates of PFASs by GAC-3 increased significantly from 0%-21% to 52%-97% after being impregnated with benzalkonium chlorides (BACs), demonstrating the superiority of this modification method. Overall, this study provided theoretical support for removing PFASs from water phase with ACs.

Land application of industrial wastes: impacts on soil quality, biota, and human health

Globally, waste disposal options such as landfill, incineration, and discharge to water, are not preferred long-term solutions due to their social, environmental, political, and economic implications. However, there is potential for increasing the sustainability of industrial processes by considering land application of industrial wastes. Applying waste to land can have beneficial outcomes including reducing waste sent to landfill and providing alternative nutrient sources for agriculture and other primary production. However, there are also potential hazards, including environmental contamination. This article reviewed the literature on industrial waste applications to soils and assessed the associated hazards and benefits. The review investigated wastes in relation to soil characteristics, dynamics between soils and waste constituents, and possible impacts on plants, animals, and humans. The current body of literature demonstrates the potential for the application of industrial waste into agricultural soils. The main challenge for applying industrial wastes to land is the presence of contaminants in some wastes and managing these to enhance positive effects and reduce negative outcomes to within acceptable limits. Examination of the literature also revealed several gaps in the research and opportunities for further investigation: specifically, a lack of long-term experiments and mass balance assessments, variable waste composition, and negative public opinion.

Indirect potable water reuse to face drought events in Barcelona city. Setting a monitoring procedure to protect aquatic ecosystems and to ensure a safe drinking water supply

The climate change and increasing anthropogenic pressures are expected to limit the availability of water resources. Hence, active measures must be planned in vulnerable regions to ensure a sustainable water supply and minimize environmental impacts. A pilot test was carried out in the Llobregat River (NE Spain) aiming to provide a useful procedure to cope with severe droughts through indirect water reuse. Reclaimed water was used to restore the minimum flow of the lower Llobregat River, ensuring a suitable water supply downstream for Barcelona. A monitoring was performed to assess chemical and microbiological threats throughout the water treatment train, the river and the final drinking water, including 376 micropollutants and common microbiological indicators. The effects of water disinfection were studied by chlorinating reclaimed water prior to its discharge into the river. Data showed that 10 micropollutants (bromodichloromethane, dibromochloromethane, chloroform, EDDP, diclofenac, iopamidol, ioprimid, lamotrigine, ofloxacin and valsartan) posed a potential risk to aquatic life, whereas one solvent (1,4-dioxane) could affect human health. The chlorination of reclaimed water mitigated the occurrence of pharmaceuticals but, conversely, the concentration of halogenated disinfection by-products increased. From a microbiological perspective, the microbial load decreased along wastewater treatments and, later, along drinking water treatment, ultimately reaching undetectable values in final potable water. Non-chlorinated reclaimed water showed a lower log reduction of E. coli and coliphages than chlorinated water. However, the effect of disinfection vanished once reclaimed water was discharged into the river, as the basal concentration of microorganisms in the Llobregat River was comparable to that of non-chlorinated reclaimed water. Overall, our study indicates that indirect water reuse can be a valid alternative source of drinking water in densely populated areas such as Barcelona (Catalonia - NE Spain). A suitable monitoring procedure is presented to assess the related risks to human health and the aquatic ecosystem.

A Review on Removal and Destruction of Per- and Polyfluoroalkyl Substances (PFAS) by Novel Membranes

Per- and Polyfluoroalkyl Substances (PFAS) are anthropogenic chemicals consisting of thousands of individual species. PFAS consists of a fully or partly fluorinated carbon–fluorine bond, which is hard to break and requires a high amount of energy (536 kJ/mole). Resulting from their unique hydrophobic/oleophobic nature and their chemical and mechanical stability, they are highly resistant to thermal, chemical, and biological degradation. PFAS have been used extensively worldwide since the 1940s in various products such as non-stick household items, food-packaging, cosmetics, electronics, and firefighting foams. Exposure to PFAS may lead to health issues such as hormonal imbalances, a compromised immune system, cancer, fertility disorders, and adverse effects on fetal growth and learning ability in children. To date, very few novel membrane approaches have been reported effective in removing and destroying PFAS. Therefore, this article provides a critical review of PFAS treatment and removal approaches by membrane separation systems. We discuss recently reported novel and effective membrane techniques for PFAS separation and include a detailed discussion of parameters affecting PFAS membrane separation and destruction. Moreover, an estimation of cost analysis is also included for each treatment technology. Additionally, since the PFAS treatment technology is still growing, we have incorporated several future directions for efficient PFAS treatment.

Effect-Directed Analysis Based on the Reduced Human Transcriptome (RHT) to Identify Organic Contaminants in Source and Tap Waters along the Yangtze River

Since a large number of contaminants are detected in source waters (SWs) and tap waters (TWs), it is important to perform a comprehensive effect evaluation and key contributor identification. A reduced human transcriptome (RHT)-based effect-directed analysis, which consisted of a concentration-dependent RHT to reveal the comprehensive effects and noteworthy pathways and systematic identification of key contributors based on the interactions between compounds and pathway effects, was developed and applied to typical SWs and TWs along the Yangtze River. By RHT, 42% more differentially expressed genes and 33% more pathways were identified in the middle and lower reaches, indicating heavier pollution. Hormone and immune pathways were prioritized based on the detection frequency, sensitivity, and removal efficiency, among which the estrogen receptor pathway was the most noteworthy. Consistent with RHT, estrogenic effects were widespread along the Yangtze River based on in vitro evaluations. Furthermore, 38 of 100 targets, 39 pathway-related suspects, and 16 estrogenic nontargets were systematically identified. Among them, diethylstilbestrol was the dominant contributor, with the estradiol equivalent (EEQ) significantly correlated with EEQ_water. In addition, zearalenone and niclosamide explained up to 54% of the EEQ_water. The RHT-based EDA method could support the effect evaluation, contributor identification, and risk management of micropolluted waters.

Per- and polyfluoralkyl substances (PFAS) in drinking water system: Target and non-target screening and removal assessment

The massive use and the persistence of per- and polyfluoroalkyl substances (PFAS) have led to their frequent detection in aquatic environments, which may further threaten drinking water safety. So far, our knowledge about the occurrence of PFAS in drinking water system is still very limited. Here we investigated the occurrence and removal of PFAS in a drinking water system using non-target, suspect and target screening strategies. Sampling was performed in three seasons in the drinking water system including a water source, two drinking water treatment plants, and tap water in five households. The results showed detection of 17 homologous series with 51 homologues in non-target screening and 50 potential PFAS detected in suspect screening. Probable structures were proposed for 15 PFAS with high confidence levels (the first three of the five levels), with seven of them being reported for the first time in drinking water system. Semi-quantification was performed on seven homologous series based on target PFAS, the estimated total concentrations for non-target PFAS ranged between 4.10 and 17.6 ng/L. Nine out of 50 target PFAS were found and precisely quantified (<LOQ-13.4 ng/L) with predominance of perfluorocarboxylic acids (PFCA) and perfluorosulfonic acids (PFSA). All target and non-target PFAS were detected in tap water with similar concentrations in all three seasons. Removal efficiency for the detected PFAS in each processing unit was almost zero, indicating the recalcitrance of these chemicals to the conventional treatment process. The findings from this study clearly show the wide presence of PFAS in the whole drinking water treatment process, and suggest an urgent need for effective removal technology for this group of chemicals.

Novel Fluorinated Nitrogen-Rich Porous Organic Polymer for Efficient Removal of Perfluorooctanoic Acid from Water

The mobility, durability, and widespread use of perfluorinated and polyfluoroalkyl substances (PFAS), notably perfluorooctanoic acid (PFOA), bring about serious contamination of many ground and surface waters. In this study, fluorine and amine-functionalized porous organic polymer (POP-4F) was designed and successfully synthesized as an adsorbent for PFOA removal in water. The characterization results showed that the synthesized material had an amorphous microporous structure, and the BET surface area was up to 479 m2 g−1. Its versatile adsorption property was evaluated by batch adsorption experiments using PFOA as a probe. The experiments show that the polymer was able to remove 98% of the PFOA in 5 min from water and then desorb within 3 min in methanol ([PFOA]0 = 1 mg L−1; [POP-4F] = 200 mg L−1). Specifically, the adsorption capacity of POP-4F is up to 107 mg g−1, according to the Langmuir fit. The rapid adsorption and desorption of PFOA by POP-4F offers the possibility of economical, environmentally friendly, and efficient treatment of real wastewater.

Experimental insights into anodic oxidation of hexafluoropropylene oxide dimer acid (GenX) on boron-doped diamond anodes

GenX is the trade name of the ammonium salt of hexafluoropropylene oxide dimer acid (HFPO-DA) and is used as a replacement for the banned perfluorooctanoic acid (PFOA). However, recent studies have found GenX to be more toxic than PFOA. This work deals with the electrochemical degradation of HFPO-DA using boron-doped diamond anodes. For the first time, an experimental study was conducted to investigate the influence of sulfate concentration and other operating parameters on HFPO-DA degradation. Results demonstrated that sulfate radicals were ineffective in HFPO-DA degradation due to steric hindrance by -CF₃ branch. Direct electron transfer was found as the rate-determining step. By comparing degradation of HFPO-DA with that of PFOA, it was observed that the steric hindrance by -CF₃ branch in HFPO-DA decreased the rate of electron transfer from the carboxyl head group even though its defluorination rate was faster. Conclusively, a degradation pathway is proposed in which HFPO-DA mineralizes to CO₂ and F- via formation of three intermediates.

Removal of per- and poly-fluoroalkyl substances (PFASs) by wetlands: Prospects on plants, microbes and the interplay

Per- and polyfluoroalkyl substances (PFASs) represent a large family of synthetic organofluorine aliphatic compounds. They have been extensively produced since 1940s due to enormous applications as a surface-active agent, and water and oil repellent characteristics. PFASs are made to be non-biodegradable, therefore, many of them have been found in the environment albeit strict regulations have been in place since 2002. PFASs are extremely toxic compounds that can impart harm in both fauna and flora. Recent investigations have shown that wetlands might be useful for their removal from the environment as a passive and nature-based solution. To this end, understanding the role of plants, microbes, and their combined plant-microbe interplay is crucial because it could help design a sophisticated passive treatment wetland system. This review focuses on how these components (plants, microbe, substrate) can influence PFASs removal in wetlands under natural and controlled conditions. The information on underlying removal mechanisms is mostly retrieved from laboratory-based studies; however, pilot- and field-scale data are also presented to provide insights on their real-time performance. Briefly, a traditional wetland system works on the principles of phytouptake, bioaccumulation, and sorption, which are mainly due to the fact that PFASs are synthetic compounds that have very low reactivity in the environment. Nevertheless, recent investigations have also shown that Feammox process in wetlands can mineralize the PFASs; thus, opens new opportunities for PFASs degradation in terms of effective plant-microbe interplay in the wetlands. The choice of plants and bacterial species is however crucial, and the system efficiency relies on species-specific, sediment-specific and pollutant-specific principles. More research is encouraged to identify genetic elements and molecular mechanisms that can help us harness effective plant-microbe interplay in wetlands for the successful removal of PFASs from the environment.

Membrane-based technologies for per- and poly-fluoroalkyl substances (PFASs) removal from water: Removal mechanisms, applications, challenges and perspectives

Water purification from per- and poly-fluoroalkyl substances (PFASs), as a group of persistent and mobile fluoro-organic contaminants, is receiving increasing attention worldwide due to the ubiquitous presence of these highly toxic compounds. To reduce the risk of exposure of human life to PFASs and their dispersion in the environment, various techniques, primarily based on membrane technologies, have been rapidly developed. Here we critically review and analyze the current state-of-the-art of membrane-based techniques for PFASs removal, including direct membrane filtrations, adsorption-based membranes, and hybrid membrane processes. Membranes performance, treatment efficiencies, characteristic parameters and mechanisms for PFASs removal are discussed in detail. We highlight and discuss advantages and limitations, as well as challenges and prospects of individual membrane-based PFASs treatments, pointing towards the practical and sustainable application of these technologies.

Supercritical Water Oxidation as an Innovative Technology for PFAS Destruction

Water above 374 °C and 22.1 MPa, becomes supercritical, a special state where organic solubility increases and oxidation processes are accelerated. Supercritical water oxidation (SCWO) has been previously shown to destroy hazardous substances such as halogenated compounds. Three separate providers of SCWO technology were contracted to test the efficacy of SCWO systems to reduce per- and poly-fluoroalkyl substances (PFAS) concentrations from solutions of dilute aqueous film-forming foam (AFFF). The findings of all three demonstration studies, showed greater than 99% reduction of the total PFAS identified in a targeted-compound analysis, including perfluorooctanesulfonic acid (PFOS) and perfluorooctanoic acid (PFOA). PFOS was reduced from 26.2 mg/L to 240 μg/L, 30.4 mg/L to 0.310 μg/L, and 190 mg/L to 8.57 μg/L, from the Aquarden, Battelle, and 374Water demonstrations, respectively. Similarly, PFOA was reduced from 930 to 0.14 μg/L, 883 to 0.102 μg/L, and 3,100 μg/L to non-detect in the three evaluations. Additionally, chemical oxygen demand of the dilute AFFF was shown to reduce from 4,750 to 5.17 mg/L after treatment, indicating significant organic compound destruction. In one demonstration, a mass balance of the influent and effluent found that the targeted compounds accounted for only 27% of the generated fluoride, suggesting that more PFAS were destroyed than measured and emphasizing the limitations of targeted analysis alone. As a destructive technology, SCWO may be an alternative to incineration and could be a permanent solution for PFAS-laden wastewaters rather than disposal by injection into a deep-well or landfilling. Additional investigation of reaction by-products remains to be conducted for a complete assessment of SCWO's potential as a safe and effective PFAS treatment technology.

NMR spectroscopy of wastewater: A review, case study, and future potential

NMR spectroscopy is arguably the most powerful tool for the study of molecular structures and interactions, and is increasingly being applied to environmental research, such as the study of wastewater. With over 97% of the planet's water being saltwater, and two thirds of freshwater being frozen in the ice caps and glaciers, there is a significant need to maintain and reuse the remaining 1%, which is a precious resource, critical to the sustainability of most life on Earth. Sanitation and reutilization of wastewater is an important method of water conservation, especially in arid regions, making the understanding of wastewater itself, and of its treatment processes, a highly relevant area of environmental research. Here, the benefits, challenges and subtleties of using NMR spectroscopy for the analysis of wastewater are considered. First, the techniques available to overcome the specific challenges arising from the nature of wastewater (which is a complex and dilute matrix), including an examination of sample preparation and NMR techniques (such as solvent suppression), in both the solid and solution states, are discussed. Then, the arsenal of available NMR techniques for both structure elucidation (e.g., heteronuclear, multidimensional NMR, homonuclear scalar coupling-based experiments) and the study of intermolecular interactions (e.g., diffusion, nuclear Overhauser and saturation transfer-based techniques) in wastewater are examined. Examples of wastewater NMR studies from the literature are reviewed and potential areas for future research are identified. Organized by nucleus, this review includes the common heteronuclei (¹³C, ¹⁵N, ¹⁹F, ³¹P, ²⁹Si) as well as other environmentally relevant nuclei and metals such as ²⁷Al, ⁵¹V, ²⁰⁷Pb and ¹¹³Cd, among others. Further, the potential of additional NMR methods such as comprehensive multiphase NMR, NMR microscopy and hyphenated techniques (for example, LC-SPE-NMR-MS) for advancing the current understanding of wastewater are discussed. In addition, a case study that combines natural abundance (i.e. non-concentrated), targeted and non-targeted NMR to characterize wastewater, along with in vivo based NMR to understand its toxicity, is included. The study demonstrates that, when applied comprehensively, NMR can provide unique insights into not just the structure, but also potential impacts, of wastewater and wastewater treatment processes. Finally, low-field NMR, which holds considerable future potential for on-site wastewater monitoring, is briefly discussed. In summary, NMR spectroscopy is one of the most versatile tools in modern science, with abilities to study all phases (gases, liquids, gels and solids), chemical structures, interactions, interfaces, toxicity and much more. The authors hope this review will inspire more scientists to embrace NMR, given its huge potential for both wastewater analysis in particular and environmental research in general.

Managing and treating per- and polyfluoroalkyl substances (PFAS) in membrane concentrates

Per- and polyfluoroalkyl substances (PFAS), which are present in many waters, have detrimental impacts on human health and the environment. Reverse osmosis (RO) and nanofiltration (NF) have shown excellent PFAS separation performance in water treatment; however, these membrane systems do not destroy PFAS but produce concentrated residual streams that need to be managed. Complete destruction of PFAS in RO and NF concentrate streams is ideal, but long-term sequestration strategies are also employed. Because no single technology is adequate for all situations, a range of processes are reviewed here that hold promise as components of treatment schemes for PFAS-laden membrane system concentrates. Attention is also given to relevant concentration processes because it is beneficial to reduce concentrate volume prior to PFAS destruction or sequestration. Given the costs and challenges of managing PFAS in membrane concentrates, it is critical to evaluate both established and emerging technologies in selecting processes for immediate use and continued research.

Yale School of Public Health Symposium: An overview of the challenges and opportunities associated with per- and polyfluoroalkyl substances (PFAS)

On December 13, 2019, the Yale School of Public Health hosted a symposium titled "Per- and Polyfluoroalkyl Substances (PFAS): Challenges and Opportunities" in New Haven, Connecticut. The meeting focused on the current state of the science on these chemicals, highlighted the challenges unique to PFAS, and explored promising opportunities for addressing them. It brought together participants from Yale University, the National Institute of Environmental Health Sciences, the University of Massachusetts Amherst, the University of Connecticut, the Connecticut Agricultural Experiment Station, the Connecticut Departments of Public Health and Energy and Environmental Protection, and the public and private sectors. Presentations during the symposium centered around several primary themes. The first reviewed the current state of the science on the health effects associated with PFAS exposure and noted key areas that warranted future research. As research in this field relies on specialized laboratory analyses, the second theme considered commercially available methods for PFAS analysis as well as several emerging analytical approaches that support health studies and facilitate the investigation of a broader range of PFAS. Since mitigation of PFAS exposure requires prevention and cleanup of contamination, the third theme highlighted new nanotechnology-enabled PFAS remediation technologies and explored the potential of green chemistry to develop safer alternatives to PFAS. The fourth theme covered collaborative efforts to assess the vulnerability of in-state private wells and small public water supplies to PFAS contamination by adjacent landfills, and the fifth focused on strategies that promote successful community engagement. This symposium supported a unique interdisciplinary coalition established during the development of Connecticut's PFAS Action Plan, and discussions occurring throughout the symposium revealed opportunities for collaborations among Connecticut scientists, state and local officials, and community advocates. In doing so, it bolstered the State of Connecticut's efforts to implement the ambitious initiatives that its PFAS Action Plan recommends.

Determination of perfluorooctane sulphonate and perfluorooctanoic acid in seafood and water from Map Ta Phut Industrial Estate area, Thailand

This initial study aimed to determine the concentrations of perfluorooctane sulphonate (PFOS) and perfluorooctanoic acid (PFOA) in seafood, bottled drinking water, and surface and tap water collected from Map Ta Phut Industrial Estate in Rayong province, Thailand. Samples were collected during dry (January) and wet (June) seasons, 2019. The perfluorinated compounds were cleaned up by solid phase extraction and analysed by ultra-performance liquid chromatography-tandem mass spectrometry with stable isotopic labelled internal standards (13C8-PFOS and 13C8-PFOA). This study reports concentrations of PFOS and PFOA in seafood at levels between 29-6724 and <48-421 ng/kg wet weight, respectively. Surface water samples from rivers and the coastal sea had PFOS and PFOA between 0.60-465.65 and <0.25-59.29 ng/L, respectively. Contamination of PFOS and PFOA in bottled drinking water (<0.125-0.454 and <0.25-0.621 ng/L, respectively) did not exceed the USEPA standard of 70 ng/L. Concentrations of PFOS and PFOA in seafood and water samples between seasons did not show any definite trend. Seafood dietary assessments of PFOS exposure in the seafood eater population raised a health concern, as the exposure exceeded the latest EFSA tolerable weekly intake value for PFAS mixtures (4.4 ng/kg body weight/week). Therefore, environmental and food samples from Map Ta Phut area should be closely monitored to ensure the safety of people living in and around this area.

Removal of per- and polyfluoroalkyl substances from aqueous media using synthesized silver nanocomposite-activated carbons

PURPOSE

Per- and polyfluoroalkyl substances (PFAS) have been found to be widespread, extremely persistent and bioaccumulative with toxicity tendencies. Pre-synthesized nanocomposite-activated carbons, referred to, as physically activated maize tassel silver (PAMTAg) and chemically activated maize tassel silver (CAMTAg) were utilized in the present study. They were used for the removal of 10 PFAS from aqueous solutions.

METHODS

The nanocomposite-activated carbons were characterized via scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, Brunauer Emmett Teller (BET) and other techniques. Batch equilibrium experiments were conducted in order to investigate the effects of solution pH, adsorbent dosage, initial PFAS concentration and temperature on the removal of PFAS using PAMTAg and CAMTAg. Langmuir and Freundlich adsorption isotherm models were used to analyse the equilibrium data obtained.

RESULTS

Maximum adsorption capacities of 454.1 mg/g (0.91 mmol/g) and 321.2 mg/g (0.78 mmol/g) were recorded for perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA), respectively using CAMTAg. The values recorded for the Gibbs' free energy (ΔG°) for the adsorption of PFOS and PFOA onto PAMTAg and CAMTAg were negative; PFOS (-9.61, -9.99 and - 10.39), PFOA (-8.77, -9.76 and - 10.21) using PAMTAg; and PFOS (-13.70, -12.70 and - 12.37), PFOA (-12.86, -12.21 and - 11.17) using CAMTAg. Therefore, the adsorption processes were spontaneous and feasible. The values recorded for enthalpy (ΔH°) (kJ/mol) for the adsorption of PFOS (-26.15) and PFOA (-35.86) onto CAMTAg were negative, indicating that the adsorption mechanism is exothermic in nature. Positive values were recorded for ΔH° for the adsorption of PFOS (2.32) and PFOA (12.69) onto PAMTAg, indicative of an endothermic adsorption mechanism. Positive entropy (ΔS°) values (0.04 and 0.07) were recorded for PFOS and PFOA using PAMTAg; whereas negative values (-0.04 and - 0.08) were recorded for ΔS° using CAMTAg. A positive ΔS° indicates an increase in randomness of the adsorbate at the solid-solution interface and the reverse is the case for a negative ΔS°.

CONCLUSION

The interplay of electrostatic attraction and hydrophobic interactions enabled the removal of PFAS using PAMTAg and CAMTAg. Findings suggest that PAMTAg and CAMTAg are effective for the removal of PFAS from aqueous media and are good alternatives to commercially available activated carbons.

GRAPHICAL ABSTRACT

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s40201-020-00597-3.

Toxic effects and mechanisms of PFOA and its substitute GenX on the photosynthesis of Chlorella pyrenoidosa

Perfluorooctanoic acid (PFOA) and its substitute GenX are toxic chemicals that are widespread in the aquatic environment. However, there is little information about their toxicity mechanisms to aquatic organisms. In this study, Chlorella pyrenoidosa (C. pyrenoidosa) was treated with two concentrations (100 ng L^-1 and 100 μg L^-1) of PFOA or GenX for 12 days. The results showed that these two concentrations of PFOA and GenX began to inhibit the growth of algae after 6 days of treatment, and the Chlorophyll content and photosynthetic activity of C. pyrenoidosa were also negatively affected by these two chemicals. The transcriptomic results indicated that most of the genes related to the photosynthetic metabolism of C. pyrenoidosa were down-regulated (in 100 ng L^-1 treatment groups) on the 12th day. Besides, GenX and PFOA showed similar effects on algae photosynthesis including physical damage and metabolic disorders. According to this study, GenX might not be an ideal substitute for PFOA, and more attention should be paid on the management of emerging perfluoroalkyl substances.

Effectiveness of household water purifiers in removing perfluoroalkyl substances from drinking water

Drinking water is one of the major exposure routes to Perfluoroalkyl substances (PFASs). These chemicals are scarcely removed by the conventional process in water purification plants. In the present study, four models of pitcher-type water purifiers (A-D) were tested to evaluate their removal effect on six PFASs including PFOS and PFOA. All of the water purifiers removed PFASs, but the efficiency was dependent on the models. Model C was most effective; more than 90% of all PFASs were removed through the recommended life of the filter cartridge. Model D was least effective; its removal efficiency declined below 50% by the end of the cartridge's life. When compared by the carbon chain length of PFASs, the removal efficiency was "C₁₂ > C₁₀ > C₈ > C₆" in all models. This study clearly demonstrates that household water purifiers are effective in decreasing the exposure to PFASs through drinking water.

Reverse osmosis and nanofiltration membranes for highly efficient PFASs removal: overview, challenges and future perspectives

PFASs are called “forever chemicals” because they do not fully degrade. They have become so ubiquitous in the environment that it is difficult to prevent exposure. This review aims to provide a set of improved technologies to remove PFASs from water.

Environmental and dietary exposure of perfluorooctanoic acid and perfluorooctanesulfonic acid in the Nakdong River, Korea

This study performed the first environmental and dietary exposure assessment to explore plant uptake of perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS) from agricultural soil and irrigation water in the Nakdong River delta, South Korea. Annual average concentrations of total PFOA and PFOS ranged from 0.026 to 0.112 µg L^-1 (irrigation water), and from 0.818 to 1.364 µg kg^-1 (soil), respectively. PFOA and PFOS hotspots were identified downstream of the Nakdong River and were influenced by seasonal climatic variations. The observed average biennial concentration of the sum of PFOA and PFOS decreased in irrigation water, from 0.112 µg L^-1 in 2013 to 0.026 µg L^-1 in 2015, suggests that the 2013 Persistent Organic Pollutants Control Act may have helped to reduce levels of PFAS at this location. This study calculated some of the highest plant uptake factors reported to date, with values ranging from 0.962 in green onions to < 0.004 in plums. Leafy vegetables and rice are important components of the Korean diet; these groups had the largest contribution to the estimated dietary intake of PFOA and PFOS, which was calculated at 0.449 and 0.140 ng kg _bw ^-1 day^-1, respectively. This corresponded to 66.4% for PFOA and 7.9% for PFOS of the EFSA reference dose (RfD). The dietary intake of PFOA and PFOS from crops alone did not exceed the RfD. However, when the estimated daily intake (EDI) from other sources such as tap water, meat, fish, dairy, and beverages was included in the exposure risk assessment, both of the EDIs to PFOA and PFOS exceeded the RfDs, indicating that there may be a risk to human health. This study concludes that consumption of crops might, therefore, be a significant and underappreciated pathway for human exposure to PFAS.

Lethal and sublethal toxicity of perfluorooctanoic acid (PFOA) in chronic tests with Hyalella azteca (amphipod) and early-life stage tests with Pimephales promelas (fathead minnow)

Perfluoroalkyl substances (PFAS), including perfluorooctanoic acid (PFOA), are industrial chemicals that are of concern due to their environmental presence, persistence, bioaccumulative potential, toxicity, and capacity for long-range transport. Despite a large body of research on environmental exposure, insufficient chronic aquatic toxicity data exist to develop water quality targets for clean-up of federal contaminated sites in Canada. Thus, our objective was to assess the aqueous toxicity of PFOA in chronic tests with Hyalella azteca (amphipod) and early-life stage tests with Pimephales promelas (fathead minnow). Toxicity data were analyzed based on measured PFOA concentrations. Amphipod exposures were 42 d (0.84-97 mg/L) and examined survival, growth, and reproduction. Fathead minnow exposures were 21 d (0.010-76 mg/L), which encompassed hatching (5 d) and larval stages until 16 d post-hatch; endpoints included hatching success, deformities at hatch, and larval survival and growth. Amphipod survival was significantly reduced at 97 mg/L (42-d LC50 = 51 mg/L), but growth and reproduction were more sensitive endpoints (42-d EC50 for both endpoints = 2.3 mg/L). Fathead minnows were less sensitive than amphipods, exhibiting no significant effects in all endpoints with the exception of uninflated swim bladder, which was significantly higher at 76 mg/L (15%) than controls (0%). Maximum concentrations of PFOA are generally in the ng/L range in global surface waters, but can reach the μg/L range in close proximity to major source inputs; therefore, environmental concentrations are well below those that caused toxicity in the current study. Our data will provide valuable information with which to assess the risk of PFOA at contaminated sites, and to set a target for site remediation.

Perfluoroalkyl substances and pharmaceuticals removal in full-scale drinking water treatment plants

The concentrations of 14 perfluoroalkyl substances (PFASs) and 46 pharmaceuticals in raw water and drinking water from five drinking water treatment plants were determined to assess removal of the chemicals during treatment. 10 out of 14 PFASs were detected in the raw and drinking water samples. The mean perfluorohexane sulfonate concentrations in raw and drinking water were the highest with levels of 106 and 69.6 ng L^-1, respectively and the other PFAS concentrations were lower. The ∑₁₄PFAS and individual PFAS removal efficiencies for the treatment plants were -36.9% to 70.7% (mean 31.3%) but the granular activated carbon process removed >80% of the total amount of long-chain PFASs that was removed. The removal efficiency increased as the perfluorocarbon chain length increased. The removal efficiencies increased by 14.2% and 11.2% from the shortest to the longest perfluoroalkyl carboxylic acid and perfluoroalkyl sulfonic acid chain lengths, respectively. 20 out of 46 pharmaceuticals were detected in the raw water samples, but most were removed completely during treatment. Only caffeine, carbamazepine, crotamiton, fenbendazole, metformin, and sulfamethoxazole were detected in the drinking water samples. Oxidation processes contributed >90% of the overall treatment plant removal efficiency except for metformin.

Electrocatalytic degradation of perfluoroocatane sulfonate (PFOS) on a 3D graphene-lead dioxide (3DG-PbO2) composite anode: Electrode characterization, degradation mechanism and toxicity

In this work, a three-dimension grapnene-PbO₂ (3DG-PbO₂) composite anode was prepared using coelectrodeposition technology for electrocatalytic oxidation of perfluorooctane sulfonate (PFOS). The effect of 3DG on the surface morphology, structure and electrocatalytic activity of PbO₂ electrode was investigated. The results indicated that the 3DG-PbO₂-0.08 anode (3DG concentration in electrodeposition solution was 0.08 g L^-1) possessed the best electrocatalytic activity due to its stronger ·OH radicals generation capacity, more active sites and smaller charge-transfer resistance. The degradation rate constant of PFOS on 3DG-PbO₂-0.08 anode was 2.33 times than that of pure PbO₂ anode. Additionally, the by-products formed in electrocatalytic degradation of PFOS were identified and a PFOS degradation pathway was proposed accordingly, which was dominated by the dissociation of -CF₂- groups via the attack of ·OH radicals. Finally, the toxicity evolution of degradation solution was examined to evaluate the ecological risk of electrocatalytic oxidation of PFOS by acute toxicity assays to zebrafish embryos.

The Adsorption Selectivity of Short and Long Per- and Polyfluoroalkyl Substances (PFASs) from Surface Water Using Powder-Activated Carbon

Nine per- and polyfluoroalkyl substances (PFASs), including six perfluoroalkyl carboxylic acids (PFCAs) and three perfluoroalkyl sulfonic acids (PFSAs), were tested to find their adsorption selectivity from surface water and the feasibility of the powder activated carbon (PAC) process between the perchlorination and coagulation processes by operating parameters such as mixing intensity, dosage, contact time, initial pH, and concentration of perchlorination. The removal efficiency of four types of PAC revealed that the coal-based activated carbon was clearly advanced for all of the PFASs, and the thermal regenerated PAC did not exhibit a significant reduction in adsorption capacity. The longer carbon chain or the higher molecular weight (MW) obtained a higher adsorption capacity and the MW exhibited a more proportional relationship with the removal efficiency than the carbon chain number, regardless of the PFCA and PFSA species. Approximately 80% and 90% equilibria were accomplished within 60 and 120 min for the long chain carbon PFAS, respectively, while for the short chain PFAS, 240 min was required to reach 85% equilibrium. The effect of mixing intensity (rpm) was not considered for the removal of the PFAS, although it was relatively influenced in the short PFAS species. Due to the surface charge of the PAC and the properties of protonation of the PFASs, the acid condition increased the PFASs’ adsorption capacity. The prechlorination decreased the removal efficiency, and the reduction rate was more significantly influenced for the short chain PFAS than for the long chain PFAS.

Removal of per- and polyfluoroalkyl substances (PFASs) in a full-scale drinking water treatment plant: Long-term performance of granular activated carbon (GAC) and influence of flow-rate

Per- and polyfluoroalkyl substances (PFASs) have been ubiquitously detected in drinking water which poses a risk for human exposure. In this study, the treatment efficiency for the removal of 15 PFASs was examined in a full-scale drinking water treatment plant (DWTP) in the City of Uppsala, Sweden, over a period of two years (2015-2017). Removal of the five frequently detected PFASs was influenced by the total operation time of granular activated carbon (GAC) filters, GAC type and surface loading rate. The average removal efficiency of PFASs ranged from 92 to 100% for "young" GAC filters and decreased to 7.0-100% for "old" GAC filters (up to 357 operation days, 29 300 bed volumes (BV) treated). Flow-rates were adjusted in two full-scale GAC filters of different operational age to examine the removal of PFAS and organic matter depending on GAC operational age and operating flow. The decrease in flow-rate by 10 L s^-1 from 39 to 29 L s^-1 led to an average increase of 14% and 6.5% in total PFAS removal efficiency for an "old" (264 operation days, 21 971 BV treated) and a "young" GAC filter (63 operation days, 5 725 BV treated), respectively. A cost-analysis for various operation scenarios illustrated the dominating effect of treatment goals and costs for GAC regeneration on overall GAC operation costs. The unit costs for GAC filters ranged from 0.08 to 0.10 € m^-3 water treated and 0.020-0.025 € m^-3 water treated for a treatment goal of 10 ng L^-1 and 85 ng L^-1, respectively, for ∑₁₁PFAS. Furthermore, it was concluded that prolonging the GAC service life by lowering the flow-rates after reaching the treatment goal could lead to a 26% cost-deduction. The results and methods presented in this study give drinking water providers valuable tools for the operation of a full-scale treatment train for the removal of PFAS in contaminated raw water.

Recent Developments of PFAS-Detecting Sensors and Future Direction: A Review

Per- and poly-fluoroalkyl substances (PFASs) have recently been labeled as toxic constituents that exist in many aqueous environments. However, traditional methods used to determine the level of PFASs are often not appropriate for continuous environmental monitoring and management. Based on the current state of research, PFAS-detecting sensors have surfaced as a promising method of determination. These sensors are an innovative solution with characteristics that allow for in situ, low-cost, and easy-to-use capabilities. This paper presents a comprehensive review of the recent developments in PFAS-detecting sensors, and why the literature on determination methods has shifted in this direction compared to the traditional methods used. PFAS-detecting sensors discussed herein are primarily categorized in terms of the detection mechanism used. The topics covered also include the current limitations, as well as insight on the future direction of PFAS analyses. This paper is expected to be useful for the smart sensing technology development of PFAS detection methods and the associated environmental management best practices in smart cities of the future.

Worldwide bottled water occurrence of emerging contaminants: A review of the recent scientific literature

Contaminants of emerging concern (CECs) have recently been detected in bottled water and have brought about discussions on possible risks for human health. However, a systematic review of CECs in bottled water is currently lacking due to the relatively new introduction and/or detection of these pollutants. Hence, this paper reviews the existing studies on the presence of six major groups of emerging contaminants including microplastics (MPs), pharmaceuticals and personal care products (PPCPs), bisphenol A (BPA), phthalates, alkylphenols (APs), and perfluoroalkyl and polyfluoroalkyl substances (PFASs) in bottled water from different countries. Also, the findings related to CECs' levels, their possible sources, and their risks are summarized. The gathered data indicate that MPs within the size range of 1-5 μm are the most predominant and potentially toxic classes of MPs in bottled water. In addition, PPCPs, PFASs, APs, and BPA occur in concentration levels of ng/L, while phthalates occur in the μg/L level in bottled water. The bottle type plays an important role in the contamination level. As expected, water in plastic bottles with plastic caps is more polluted than in glass bottles. However, other sources of contamination such as contact materials during cleaning, bottling, and storage are not negligible. Based on the gathered data in this review, the CEC levels except for MPs (no threshold values) in bottled water of most countries do not raise a safety concern for the human. However, the occurrence of individual CECs and their association in bottled water need more accurate data to understand their own/synergistic effects on human health.

Spatiotemporal distribution, sources and ecological risks of perfluorinated compounds (PFCs) in the Guanlan River from the rapidly urbanizing areas of Shenzhen, China

Limited studies have demonstrated the environmental concerns of perfluorinated compounds (PFCs) in the rivers flowing through the rapidly urbanizing areas. Therefore, this study aims to investigate the spatial and temporal distribution, major sources and ecological risks of PFCs in the surface water samples, collecting from the Guanlan River, Shenzhen, China. The concentrations of ∑PFCs ranged from 11.3 to 384 ng/L, with a mean value of 81.8 ng/L in the dry season, and ranged from 6.90 to 619 ng/L, with a mean value of 339 ng/L in the wet season. Short-chain PFCs such as perfluorohexane sulfonate (PFHxS) and perfluorobutane sulfonate (PFBS) were detected as the predominant compounds. Further, the spatiotemporal distribution revealed significantly higher levels of PFCs in the wet season than those in the dry season, and relatively higher levels in the tributaries than those in the mainstream. Source apportionment highlighted the industrial discharges, domestic wastewater, precipitation, and wastewater treatment plants as the major sources of PFCs. Moreover, the population density and associated urban sewage emissions observed as important indicators for PFCs uneven distribution in the area. The ecological risk assessment revealed perfluorotetradecanoic acid (PFTA, C14) posed high ecological risks to the aquatic organisms (especially for mysid) in the Guanlan River. Taken all together, this study not only unveiled the characteristics of PFCs contamination in the rapidly urbanizing catchment, but also provided the baseline data for policy makers to protect the ecological environment of the urban rivers in the rapidly growing area.

Role of the air-water interface in removing perfluoroalkyl acids from drinking water by activated carbon treatment

Contamination of drinking water by per- and polyfluoroalkyl substances (PFASs) is a worldwide problem. In this study, we for the first time revealed the role of the air-water interface in enhancing the removal of long-chain perfluoroalkyl carboxylic (PFCAs; C_nF_2n+1COOH, n ≥ 7) and perfluoroalkane sulfonic (PFSAs; C_nF_2n+1SO₃H, n ≥ 6) acids, collectively termed as perfluoroalkyl acids (PFAAs), through combined aeration and adsorption on two kinds of activated carbon (AC). Aeration was shown to enhance the removal of long-chain PFAAs through adsorption at the air-water interface and subsequent adsorption of PFAA-enriched air bubbles to the AC. The removal of selected long-chain PFAAs was increased by 50-115 % with the assistance of aeration, depending on the perfluoroalkyl chain length. Aeration is more effective in enhancing long-chain PFAA removal as air-water interface adsorption increases with PFAA chain length due to higher surface activity. After removing adsorbed air bubbles by centrifugation, up to 80 % of the long-chain PFAAs were able to desorb from the sorbent, confirming the contribution of the air-water interface to the adsorption of PFAAs on AC. Aeration during AC treatment of water could enhance the removal of long-chain PFAAs, and improve the performance of AC during water treatment.

Selection and evaluation of water pretreatment technologies for managed aquifer recharge (MAR) with reclaimed water

Managed aquifer recharge with reclaimed water is a promising strategy for indirect potable reuse. However, residual contaminants in the treated wastewater effluent could potentially have adverse effects on human health. Hence, adequate water pretreatment is required. A multi-criteria approach was used to select and evaluate suitable water pretreatment technologies that can remove these critical contaminants in wastewater effluent for MAR identified in a previous study (Yuan et al., 2017). The treatment efficiency targets were calculated based on the concentrations and the suggested limits of critical contaminants. Treatment efficiency credits were then assigned to each treatment option for the removal of critical contaminants based on literature data. Treatment units that resulted in the highest efficiency credit scores were selected and combined into treatment train options, which were evaluated in terms of treatability, cost, and sustainability. This paper proposes an approach for the selection and evaluation of water treatment options, which will be helpful to guide the future implementation of MAR projects with reclaimed water.

Human exposure to per- and polyfluoroalkyl substances (PFAS) through drinking water: A review of the recent scientific literature

Per- and polyfluoroalkyl substances (PFAS) are a group of water-soluble chemical compounds with an important number of applications, which have been widely used during the last 60 years. Two of them, perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA), are the most known and well investigated. As for many other organic substances that are of environmental concern, the diet is the main route of human exposure to PFAS. However, in certain cases drinking water may also mean a significant contribution to human exposure, and to a lesser extent, dust and air (indoor exposure). In recent years, the environmental persistence of PFAS, their biomagnification in food webs, as well as their potential accumulation and toxicity, have generated a notable interest, which has been evidenced by the considerable number of publications in this regard. Recently, we carried out a wide revision on the levels of PFAS in food and human dietary intake. In the current review, we have summarized the recent information (last 10 years) published in the scientific literature (Scopus and PubMed) on the concentrations of PFAS in drinking water and the human health risks derived from the regular water consumption, when available. A large amount of data belongs to PFOS and PFOA and corresponds to studies mainly conducted in countries of the European Union, USA and China, although no information is available for most countries over the world. According to the toxicological information about PFAS that is so far available, the current health risks for the regular consumers of municipal/tap water do not seem to be of concern according to the levels considered as acceptable for various regulatory institutions.

Adsorption behaviour and mechanism of the PFOS substitute OBS (sodium p-perfluorous nonenoxybenzene sulfonate) on activated carbon

Perfluorooctane sulfonate (PFOS) was listed as a persistent organic pollutant by the Stockholm Convention. As a typical alternative to PFOS, sodium p-perfluorous nonenoxybenzene sulfonate (OBS) has recently been detected in the aquatic environment which has caused great concern. For the first time, the adsorption behaviour and mechanism of OBS on activated carbon (AC) with different physical and chemical properties were investigated. Decreasing the particle size of AC can accelerate its adsorption for OBS, while AC with too small particle size was not conducive to its adsorption capacity due to the destruction of its pore structure during the mechanical crushing process. Intra-particle diffusion had a lesser effect on the adsorption rate of AC with smaller particle size, higher hydrophilicity and larger pore size. Reactivation of AC by KOH can greatly enlarge their pore size and surface area, greatly increasing their adsorption capacities. The adsorption capacity of two kinds of R-GAC exceeded 0.35 mmol g^-1, significantly higher than that of other ACs. However, increasing the hydrophilicity of AC would decrease their adsorption capacities. Further investigation indicated that a larger pore size and smaller particle size can greatly enhance the adsorptive removal of OBS on AC in systems with other coexisting PFASs and organic matter due to the reduction of the pore-blocking effect. The spent AC can be successfully regenerated by methanol, and it can be partly regenerated by hot water and NaOH solution. The percentage of regeneration for the spent AC was 70.4% with 90°C water temperature and up to 95% when 5% NaOH was added into the regeneration solution. These findings are very important for developing efficient adsorbents for the removal of these newly emerging PFASs from wastewater and understanding their interfacial behaviour.

Occurrence and distribution of perfluorooctane sulfonate and perfluorooctanoic acid in three major rivers of Xinjiang, China

Drinking water is a main pathway of human exposure to perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA). These two compounds have been identified in environmental waters worldwide, but little is known about their occurrence in Xinjiang. In this study, 155 water samples were obtained from 37 locations across Ulungur River, Manasi River, and Tarim River in Xinjiang, and were assessed by using liquid chromatography tandem-mass spectrometry. PFOS and PFOA were detected in over 50% of the samples with mean concentrations of 3.194 ng/L for PFOS and 3.460 ng/L for PFOA. Spatial and regional distribution differences do exist among the three analyzed rivers. PFOS and PFOA in Manasi River were observed at the highest levels (especially in M10 and M11), but no aggravation occurred from 2014 to 2017. Seasonal variations of PFOS and PFOA concentrations showed that water samples collected during summer were higher than those in other three seasons. The occurrence, levels, and distribution patterns of PFOS and PFOA were investigated in the present study, which provides useful theory and data support for human health risk assessment. The findings of the present study can be considered for controlling these water pollutants in environmental waters.

Occurrence of perfluoroalkyl substances in selected Victorian rivers and estuaries: An historical snapshot

This reconnaissance study was undertaken in 2012 to examine the occurrence of common perfluoroalkyl substances (PFAS), including perfluoroalkyl sulphonic acids and perfluoroalkyl carboxylic acids in rivers and estuaries in Port Philip Bay, Victoria, Australia. In total, 19 PFAS were screened in grab samples of water using a combination of solid phase extraction and liquid chromatography - mass spectrometry measurement techniques. Eighteen of the PFAS screened were observed in samples. The highest level of PFOS observed at a freshwater site was 0.045 μg/L; this concentration is approximately half the draft Australian 95% species protection level for total PFOS. The highest level of PFOA in the study (0.014 μg/L) was some four orders of magnitude lower than the draft Australian trigger value for PFOA (220 μg/L). However, none of the PFAS observed at the freshwater sites had research quotient (RQ) or toxicity unit (TU) values above 1 or -3, respectively. The highest concentration of PFOS observed at an estuarine site was 0.075 μg/L; the highest level of PFOA, 0.09 μg/L). There are no Australian marine water quality trigger values for PFAS, so potential risk was assessed using the European environment quality standards (EQS) adopted in EU Directive 2013/39/EU, RQ and TU methods. In that context, none of the PFAS observed at estuary sites had concentrations higher than the EU standards, or RQ above 1 or Log 10 TU above -3. Together these assessments suggest none of the PFAS screened would have posed an acute risk to organisms in the fresh or estuary waters studied at the time of sampling on an individual or collective basis. However, the detection of these PFAS in Victorian estuaries highlights that the issue is not just an issue for more densely populated countries in the northern hemisphere, but also potentially of concern in Australia. And, in that context, more sampling campaigns in Port Philip Bay are of paramount importance to assess the potential risk pose by these compounds to aquatic ecosystems.