Assessing South American Guadua chacoensis bamboo biochar and Fe3O4 nanoparticle dispersed analogues for aqueous arsenic(V) remediation

Arsenic in Slovakia: Pollution Issues and the Potential of Magnetic Carbon Biomaterials for Wastewater Treatment

In Slovakia, there are a number of contaminated sites that have occurred due to intensive mining, mineral processing, metallurgical activities, chemical industry, fossil fuel combustion, and industrial agriculture in the past. This paper summarizes the occurrence, chemistry, toxicity, and mineralogy of arsenic species related to soil and water contamination in Slovakia. Four main localities with arsenic exposure were identified. Additionally, magnetically modified carbon biochar (MWchar-Mag) was tested for arsenic removal from a model solution alongside real mine water discharged from the abandoned Hauser adit. For the model aqueous solution, the maximum adsorption capacity was established at 6.2 mg of As per g of MWchar-Mag at natural pH. In the case of mine water with a concentration of arsenic at around 0.2 mg/L, adsorbent dosage, pH influence experiments, and kinetic tests were realized. The results confirmed 100% arsenic removal efficiency at pH~3-7 and extremely fast kinetics.

Prevention is better than a cure: A 'zero residual nanoadsorbent toxicity' downstream from its effluent exit point

Here, we offer thoughts concerning a 'zero residual nanoadsorbent toxicity' environmental policy which we strongly advocate. Our discussions in support of this policy are based on the adage 'Prevention is better than cure'. Besides emphasizing the need for strict regulations (regional and international), research and development avenues are highlighted for the technology that can achieve 'zero tolerance' for residual nanoadsorbent levels escaping and building up in receiving ecosystems. We do not oppose nanoadsorbents. On the contrary, their water and wastewater purification potentials are well recognized. However, they should not be permitted to translocate downstream from the exit point of a final effluent.

Mechanism of arsenic removal using brown seaweed derived impregnated with iron oxide biochar for batch and column studies

Water contaminated with arsenic presents serious health risks, necessitating effective and sustainable removal methods. This article proposes a method for removing arsenic from water by impregnating biochar with iron oxide (Fe2O3) from brown seaweed (Sargassum polycystum). After the seaweed biomass was pyrolyzed at 400 °C, iron oxide was added to the biochar to increase its adsorptive sites and surface functional groups, which allowed the binding of arsenic ions. Batch studies were conducted to maximize the effects of variables, including pH, contact time, arsenic concentration, and adsorbent dosage, on arsenic adsorption. The maximum arsenic adsorption efficiency of 96.7% was achieved under optimal conditions: pH 6, the adsorbent dosage of 100 mg, the initial arsenic concentration of 0.25 mg/L, and a contact time of 90 min. Langmuir and Freundlich's isotherms favored the adsorption process, while the kinetics adhered to a pseudo-second-order model, indicating chemisorption as the controlling step. Column studies revealed complete saturation after 200 min, and the adsorption behavior fits both the Adams-Bohart and Thomas models, demonstrating the potential for large-scale application. The primary mechanism underlying the interaction between iron-modified biochar and arsenic ions is surface complexation, enhanced by increased surface area and porosity. This study highlights the significant contribution of iron-modified biochar derived from macroalgae as an effective and sustainable solution for arsenic removal from water.

The feedstock anatomical properties determine biochar adsorption capacities: A study using woody bamboos (Bambuseae) and methylene blue as a model molecule

Feedstock characteristics impact biochar physicochemical properties, and reproducible biochar properties are essential for any potential application. However, in most articles, feedstock aspects (i.e., taxonomic name of the species, part of the plant, and phenological phase) are scarcely reported. This research aimed at studying the effect of species and phenological stage of the feedstock on the properties of the derived biochars and, thus, adsorption capacities in water treatment. In this study, we analysed the anatomical characteristics of three different woody bamboo species [Guadua chacoensis (GC), Phyllostachys aurea (PA), and Bambusa tuldoides (BT)] in culms harvested at two different phenological phases (young and mature), and statistically correlated them with the characteristics of the six derived biochars, including their adsorption performance in aqueous media. Sclerenchyma fibres and parenchyma cells diameter and cell-wall width significantly differed among species. Additionally, sclerenchyma fibres and parenchyma cell-wall width as well as sclerenchyma fibre cell diameters are dependent on the phenological phase of the culms. Consequently, differences in biochar characteristics (i.e., yield and average pore diameter) were also observed, leading to differential methylene blue (MB) adsorption capacities between individuals at different phenological phases. MB adsorption capacities were higher for biochar produced from young culms compared to those obtained from matures ones (i.e., GC: 628.66 vs. 507.79; BT: 537.45 vs. 477.53; PA: 477.52 vs. 462.82 mg/g), which had smaller cell wall widths leading to a lower percentage of biochar yield. The feedstock anatomical properties determined biochar characteristics which modulated adsorption capacities.

Comparison of two carbonaceous supported Fe-rich adsorbents for arsenate removal: A functionalisation and mechanistic study with applicability to groundwater treatment

The presence of arsenic in groundwater, and through this in drinking water, has been shown to present a serious risk to public health in many regions of the world. In this study, two iron-rich carbonous adsorbents were compared for the removal of arsenate (As(V)) from groundwater. Biochars (FeO-biochar and FeO-pyrochar) derived from biomass waste were functionalised in two different ways with iron chloride for comparation. Batch and dynamic parameters were optimised to achieve >99% As(V) removal efficiency. Experimental data were best described by the pseudo-second order kinetic model, while multi-stage diffusion appeared to limit mass transfer of As(V). Among the isotherm models evaluated, the Freundlich model best described the experimental results with high correlation coefficients (R2 ≥ 0.94) for both adsorbents. Monolayer adsorption capacities were found to be 4.34 mg/g and 8.66 mg/g for FeO-biochar and FeO-pyrochar, respectively. Batch studies followed by instrumental characterisation of the materials indicated the removal mechanisms involved to be electrostatic interactions (outer-sphere), OH- ligand exchange (inner-sphere complexation) and hydrogen bonding with functional groups. Higher pHpzc (9.1), SBET (167.2 m2/g), and iron/elemental content for the FeO-pyrochar (compared with the FeO-biochar) suggested that both surface chemistry and porosity/surface area were important in adsorption. Dynamic studies showed FeO-pyrochar can be used to remove As(V) from groundwater even at low 'environmental' concentrations relevant to legislative limits (<10 μg/L), whereby 7 g of FeO-pyrochar was able to treat 5.4 L groundwater.

Synthesis, delineation and technological advancements of algae biochar for sustainable remediation of the emerging pollutants from wastewater-a review

The use of algae for value-added product and biorefining applications is enchanting attention among researchers in recent years due to its remarkable photosynthetic ability, adaptability, and capacity to accumulate lipids and carbohydrates. Algae biomass, based on its low manufacturing costs, is relatively renewable, sustainable, environmentally friendly and economical in comparison with other species. High production rate of algae provides a unique opportunity for its conversion to biochar with excellent physicochemical properties, viz. high surface area and pore volume, high adsorption capacity, abundant functional groups over surface, etc. Despite several potential algal-biochar, a detailed study on its application for removal of emerging contaminants from wastewater is limited. Therefore, this technical review is being carried out to evaluate the specific elimination of inorganic and organic pollutants from wastewater, with a view to assessing adsorption performances of biochar obtained from various algae species. Species-specific adsorption of emerging pollutants from wastewater have been discussed in the present review. The promising methods like pyrolysis, gasification, dry and wet torrefaction for the production of algae biochar are highlighted. The strategies include chemical and structural modifications of algae biochar for the removal of toxic contaminants have also been considered in the current work. The overall aim of this review is to confer about the synthesis, technological advancements, delineation and application of algae biochar for the treatment of wastewater.

Effective Technique and Mechanism for Simultaneous Adsorption of As(III/V) from Wastewater by Fe-ZIF-8@MXene

Arsenic (As) contamination of surface water has become a global concern, especially for the third world countries, and it is imperative to develop advanced materials and an effective treatment method to address the issue. In this paper, iron doped ZIF-8@MXene (Fe-ZIF-8@MXene) was prepared as a potential adsorbent to effectively and simultaneously remove As(III/V) from wastewater. To investigate this, Fe-ZIF-8@MXene was characterized before and after the removal of mixed As(III/V). The results of Fourier transform infrared (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), specific surface area (BET) and point of zero charge (pHpzc) showed that Fe-ZIF-8@MXene was prepared successfully and kept a stable structure after As(III) and As(V) adsorption. The particle size of Fe-ZIF-8@MXene was in the range of 0.5 μm to 2.5 μm, where its BET was 531.7 m2/g. For both contaminants, adsorption was found to follow pseudo-second-order kinetics and was best-fitted by the Langmuir adsorption model with correlation coefficients (R2) of 0.998 and 0.997, for As(III) and As(V), respectively. The adsorbent was then applied to remove As from two actual water samples, giving maximum removal rates of 91.07% and 98.96% for As(III) and As(V), respectively. Finally, removal mechanisms for As(III/V) by Fe-ZIF-8@MXene were also explored. During the adsorption, multiple complexes were formed under the effect of its abundant surface functional groups involving multiple mechanisms, which included Van der Waals force, surface adsorption, chemical complexation and electrostatic interactions. In conclusion, this study demonstrated that Fe-ZIF-8@MXene was an advanced and reusable material for simultaneous removal of As(III/V) in wastewater.

Systematic evaluation of methods for iron-impregnation of biochar and effects on arsenic in flooded soils

There is a need for innovative strategies to decrease the mobility of metal(loids) including arsenic (As) and cadmium (Cd) in agricultural soils, including rice paddies, so as to minimize dietary exposure to these toxic elements. Iron (Fe)-modified biochars (FBCs) are used to immobilize As and Cd in soil-water systems, but there is a lack of clarity on optimal methods for preparing FBCs because there are only limited studies that directly compare BCs impregnated with Fe under different conditions. There is also a lack of information on the long-term performance of FBCs in flooded soil environments, where reductive dissolution of Fe (oxy)hydroxide phases loaded onto biochar surfaces may decrease the effectiveness of FBCs. This study uses material characterization methods including FTIR, SEM-EDX, BET, and adsorption isotherm experiments to investigate the effects of Fe-impregnation methods (pH, pyrolysis sequence, and sonication) on the morphology and mineralogy of Fe loaded onto the biochar surface, and to FBC adsorbent properties for arsenate (As(V)), arsenite (As(III)), and Cd. Acidic impregnation conditions favored the adsorption of As(III) onto amorphous Fe phases that were evenly distributed on the biochar surface, including within the biochar pore structure. The combination of sonication with acidic Fe-impregnation conditions led to the best adsorption capacities for As(V) and As(III) (4830 and 11,166 μg As g-1 biochar, respectively). Alkaline Fe-impregnation conditions led to the highest Cd adsorption capacity of 3054 μg Cd g-1 biochar, but had poor effectiveness as an As adsorbent. Amending soil with 5% (w/w) of an acid-impregnated and sonicated FBC was more effective than an alkaline-impregnated FBC or ferrihydrite in decreasing porewater As concentrations. The acid-impregnated FBC also had greater longevity, decreasing As by 54% and 56% in two flooded phases, probably due to the greater stability of Fe(III) within the biochar pore structure that may have a direct chemical bond to the biochar surface. This study demonstrates that FBCs can be designed with selectivity towards different As species or Cd and that they can maintain their effectiveness under anaerobic soil conditions. This is the first study to systematically test how impregnation conditions affect the stability of FBCs in soils under multiple drying-rewetting cycles.

Synergistic removal performance and mechanism of Cd(II) and As(III) from irrigation water by iron sulfide-based porous biochar

Since Cd(II) and As(III) have extremely opposite chemical characteristics, it is a huge challenging to simultaneously remove these two ions from aqueous solutions. Therefore, a novel iron sulfide-based porous biochar (FSB) was synthesized and used to evaluate its Cd(II) and As(III) removal performance and mechanisms. The characterization and batch experiments results indicated that FeS was successfully loaded on the surface of biochar and increased its adsorption sites. The iron sulfide-based porous biochar was very favorable for the removal of Cd(II) and As(III) in the weakly acidic environment. The maximum adsorption of Cd(II) and As(III) by FSB was 108.8 mg g-1 and 76.3 mg g-1, respectively, according to the Langmuir and Freundlich isothermal adsorption model, and the adsorption equilibrium time was 12 h and 4 h, respectively, according to the pseudo-second-order kinetic model. In the coexisting ion system, Cd(II) adsorption was suppressed by Ca2+, Mg2+, and humic acid, but enhanced by PO43- and As(III). As(III) adsorption was inhibited by PO43- and humic acid. Precipitation and complexation are the predominant adsorption mechanisms of Cd(II) and As(III), which contribute to the formation of Cd-O, Fe-O-Cd, As-O, Fe-O-As, ternary complex Cd-Fe-As, and stable compounds FeAsO4·2H2O and CdS. Therefore, The iron sulfide-based porous biochar can be an efficient and environmentally friendly candidate for the treatment of Cd(II) and As(III) co-polluted irrigation water.

Hydrochar-nanoparticle integration for arsenic removal from wastewater: Challenges, possible solutions, and future horizon

Arsenic (As) contamination poses a significant threat to human health, ecosystems, and agriculture, with levels ranging from 12 to 75% attributed to mine waste and stream sediments. This naturally element is abundant in Earth's crust and gets released into the environment through mining and rock processing, causing ≈363 million people to depend on As-contaminated groundwater. To combat this issue, introducing a sustainable hydrochar system has achieved a remarkable removal efficiency of over 92% for arsenic through adsorption. This comprehensive review presents an overview of As contamination in the environment, with a specific focus on its impact on drinking water and wastewater. It delves into the far-reaching effects of As on human health, ecosystems, aquatic systems, and agriculture, while also exploring the effectiveness of existing As treatment systems. Additionally, the study examines the potential of hydrochar as an efficient adsorbent for As removal from water/wastewater, along with other relevant adsorbents and biomass-based preparations of hydrochar. Notably, the fusion of hydrochar with nanoparticle-centric approaches presents a highly promising and environmentally friendly solution for achieving the removal of As from wastewater, exceeding >99% efficiency. This innovative approach holds immense potential for advancing the realms of green chemistry and environmental restoration. Various challenges associated with As contamination and treatment are highlighted, and proposed solutions are discussed. The review emphasizes the urgent need to advance treatment technologies, improve monitoring methods, and enhance regulatory frameworks. Looking outlook, the article underscores the importance of fostering research efforts, raising public awareness, and fostering interdisciplinary collaboration to address this critical environmental issue. Such efforts are vital for UN Sustainable Development Goals, especially clean water and sanitation (Goal 6) and climate action (Goal 13), crucial for global sustainability.

Sorption Capacity of AlOOH/FeAl2 Composites towards As(V)

The treatment of wastewater from arsenic compounds is an important and urgent problem. Composite nanostructures consisting of boehmite and iron compounds have a high adsorption capacity towards As(V) specie. In this work, the adsorption properties of nanostructured composites prepared by the oxidation of bimetallic Al/Fe nanoparticles with different iron contents were investigated. As a result of oxidation, boehmite AlOOH nanosheets are formed, with the resultant FeAl2 nanoparticles being distributed on the surface of boehmite nanosheets. The nanostructured composites prepared from Al/Fe nanoparticles containing 20 wt% Fe have been found to show the highest adsorption capacity towards As(V) specie, being 248 mg/g. The adsorption isotherms are most accurately described by the Freundlich model, with the arsenic adsorption process obeying pseudo second order kinetics. As a result of the study, the optimal ratio of Al and Fe in Al/Fe nanoparticles has been determined to obtain an AlOOH/FeAl2 composite adsorbent with a developed and accessible surface and a high sorption capacity towards As(V). This allows us to consider this material as a promising adsorbent for the removal of arsenic compounds from water.

Low Temperature Processing of Iron Oxide Nanoflakes from Red Mud Extract toward Favorable De-arsenification of Water

Iron oxide (α-Fe2O3) was synthesized from red mud extract followed by hydrothermal reaction at 150 °C/6-24 h in the presence of NH4OH. The crystallinity of α-Fe2O3 increased with reaction time as confirmed by X-ray Diffraction, while Fourier transform infrared spectroscopy and Raman illustrate the symmetric stretching vibration of the Fe-O bond in α-Fe2O3. The X-ray photoelectron spectroscopic analysis shows O 1s spectra at 530.6, 531.2, and 532 eV, signifying the lattice oxygen in Fe-O, surface oxygen defects, and oxygen in adsorbed hydroxyl groups, respectively. The morphology of α-Fe2O3 nanoflakes was noticed from field emission scanning electron microscopy and transmission electron microscopy. The developed particles reveal the BET surface area in the range of 136-347 m2/g. The maximum As(V) adsorption capacity of 32-41 mg/g was obtained for adsorbent dose of 0.25 g/L. The arsenic level could be lowered down to 2-3 μg/L (<10 μg/L as per WHO's limit) with contaminated real water (64 μg/L) using 0.25 g/L of sample dose within 5 min of adsorption.

Removal of tetracycline in aqueous solution by iron-loaded biochar derived from polymeric ferric sulfate and bagasse

In this study, the tetracycline (TC) removal performance of iron-loaded biochar (BPFSB) derived from sugarcane bagasse and polymerized iron sulfate was investigated, and the mechanism of TC removal was also explored by study of isotherms, kinetics and thermodynamics and characterization of fresh and used BPFSB (XRD, FTIR, SEM and XPS). The results showed that under optimized conditions (initial pH 2; BPFSB dosage 0.8 g·L-1; TC initial concentration 100 mg·L-1; Contact time 24 h; temperature 298 K), the removal efficiency of TC was as high as 99.03%. The isothermal removal of TC followed well the Langmuir, Freundlich, and Temkin models, indicating that multilayer surface chemisorption dominated the TC removal. The maximum removal capacity of TC by BPFSB at different temperatures was 185.5 mg·g-1 (298 K), 192.7 mg·g-1 (308 K), and 230.9 mg·g-1 (318 K), respectively. The pseudo-second-kinetic model described the TC removal better, while its rate-controlling step was a combination of liquid film diffusion, intraparticle diffusion, and chemical reaction. Meanwhile, TC removal was also a spontaneous and endothermic process, during which the randomness and disorder between the solid-liquid interface was increased. According to the characterization of BPFSBs before and after TC removal, H-bonding and complexation were the major interactions for TC surface adsorption. Furthermore, BPFSB was efficiently regenerated by NaOH. In summary, BPFSB had the potential for practical application in TC removal.

Biochar modification to enhance arsenic removal from water: a review

Arsenic (As) contamination is a major threat to drinking water quality throughout the world, and the development of appropriate remediation methods is critical. Adsorption is considered the most effective method for remediation of As-contaminated water. Biochar is a promising adsorbent and widely discussed for As removal due to its potential low cost and environmental friendliness. However, pristine biochar generally exhibited relatively low adsorption capacity for As mainly due to the electrostatic repulsion between the negatively charged biochar and As. Biochar modification, especially metal modification, was developed to boost the adsorption capacity for As. A systematic analysis of As removal as affected by biochar properties and modification will be of great help for As removal. This paper presents a comprehensive review on As removal by biochars from different feedstock, preparation procedures, and modification methods, with a major focus on the possible mechanisms of interaction between As and biochar. Biochar derived from sewage sludge exhibited relatively high adsorption capacity for As. Considering energy conservation, biochars prepared at 401-500 °C were more favorable in adsorbing As. Fe-modified biochar was the most popular modified biochar for As remediation due to its low cost and high efficiency. In addition, the limitations of the current studies and future perspectives are presented. The aim of this review is to provide guidance for the preparation of low-cost, environmentally friendly, and high efficiency biochar for the remediation of As-contaminated water.

Bamboo-derived adsorbents for environmental remediation: A review of recent progress

The bamboo family of plants is one of the fastest-growing species in the world. As such, there is an abundance of bamboo residues available for exploitation, especially in southeast Asian, central African and south American regions. The preparation of efficient adsorbents from bamboo residues is an emerging exploitation pathway. Biochars, activated carbons or raw bamboo fibers embedded with nanoparticles, each class of materials has been shown to be highly efficient in adsorption processes. This review aims to summarize recent findings in the application of bamboo-based adsorbents in the removal of organic, inorganic, or gaseous pollutants. Therefore, this review first discusses the preparation methods and surface modification methodologies and their effects on the adsorbent elemental content and other basic properties. The following sections assess the recent progress in the adsorption of heavy metals, organics, and gaseous substances by bamboo-based adsorbents, focusing on the optimum adsorption capacities, adsorption mechanisms and the optimum-fitting kinetic models and isotherms. Finally, research gaps were identified and directions for future research are proposed.

Efficient aqueous molybdenum removal using commercial Douglas fir biochar and its iron oxide hybrids

Molybdenum (Mo) is a naturally-occurring trace element in drinking water. Most commonly, molybdate anions (MoO₄^2-) are in well water and breast milk. In addition, it is used in medical image testing. Recently, the EPA classified Mo as a potential contaminant, as exposure can lead to health effects such as gout, hyperuricemia, and even lung cancer. We have assessed the sorptive removal of aqueous molybdate using Douglas fir biochar (DFBC) and a hybrid DFBC/Fe₃O₄ composite containing chemically-coprecipitated iron oxide (Fe₃O₄). Adsorption was studied at various: pH values, equilibrium times (5 min-24 h), initial Mo concentrations (2.5-1000 mg/L), and temperatures (5, 25, and 40 °C) using batch sorption and fixed-bed column equilibrium methods. Langmuir capacities for DFBC and DFBC/Fe₃O₄ (at pH 3, 2 hrs equilibrium) were within 459.3-487.9 mg/g and 288-572 mg/g, respectively. These adsorbents and their Mo-laden counterparts were characterized by elemental analysis, BET, PZC, SEM, TEM, EDS, XRD, and XPS. MoO₄^2- adsorption on DFBC is thought to be governed primarily via electrostatic attraction. Adsorption by DFBC/Fe₃O₄ is primarily governed by chemisorption onto magnetite surface hydroxyl groups, while electrostatics prevail in the DFBC-exposed phase. Stoichiometric precipitation of iron molybdates triggered by iron dissolution was also considered. The data suggest that DFBC and DFBC/Fe₃O₄ are promising candidates for molybdate sorption.

Paracetamol and Ibuprofen Removal from Aqueous Phase Using a Ceramic-Derived Activated Carbon

Emerging pollutants, including pharmaceuticals and personal care products, have been detected in surface and groundwaters. The adsorption of paracetamol and ibuprofen, two widespread drugs, has been studied in aqueous medium, using a ceramic-derived carbon (CeDC) and a commercial activated carbon (CoAC). CeDC yielded a BET surface area of 895 m² g^-1, a bimodal pore size distribution (13.2 and 35 nm) and a total pore volume of 1.99 cm³ g^-1. CoAC had an approximate surface area of 1000 m² g^-1, a homogeneous pore size distribution and a total pore volume of 0.42 cm³ g^-1. Kinetic and equilibrium tests were carried out in batch systems to study the materials' sorption performances. The intraparticle diffusion model best fitted the experimental kinetic data. The maximum ibuprofen sorption capacities were 120 mg g^-1 and 133 mg g^-1 for CoAC and CeDC, respectively, whereas no major differences on the maximum paracetamol sorption capacities (qm) were observed among the sorbents (150-159 mg g^-1). Therefore, CeDC, synthesized easily from a ceramic composite, improved time and sorption capacity of paracetamol and ibuprofen compared to the commercial activated carbon, indicating the potential of the developed carbon as an emerging pollutant sorbent material.

Modeling of the As (III) adsorption using Fe impregnated polyethylene terephthalate char matrix: A statistical approach

The present research aimed to analyse the impact of economical Fe impregnated polyethylene terephthalate (PET) char (PETC-Fe) for adsorption of As (III) through series of column experiments. For an inlet arsenite concentration of 1,000 μg/L, PETC-Fe exhibits excellent uptake capacity of 1,892 μg/g. Central composite design (CCD) in response surface methodology (RSM) was used to evaluate the influence of various process variables on the response function (breakthrough time) for optimization and assessment of interaction effects. The breakthrough time is more responsive to influent As (III) concentration and bed height than inlet flow rate, according to the perturbation plot. Adams-Bohart, Bed Depth Service Time (BDST) model, and Thomas models were used to model the dynamics of the adsorption system. The BDST model suited the experimental data well in the early part of the breakthrough curve, but there were minor variations over the breakpoints. Despite the fact that the experimental values and the data sets estimated using the Adams-Bohart model followed a similar pattern, they differed slightly. The PETC-Fe was found to be a sustainable and highly economical adsorbent, with a desorption performance of more than 97%, indicating the adsorbent's reusability. This adsorbent's excellent As (III) uptake capacity and regeneration performance imply that it might be used in industrial/domestic applications, and the information obtained could aid in future scaling up of the adsorption system.

Preparation and Adsorption Properties of Nanostructured Composites Derived from Al/Fe Nanoparticles with Respect to Arsenic

Composite nanostructures containing iron in different forms exhibit a high adsorption capacity with respect to arsenic. The aim of our study was to investigate the adsorption activity of an adsorbent composite prepared by the oxidation of bimetallic Al/Fe nanoparticles under different conditions. Depending on the oxidation conditions, nanostructures with different morphologies in the form of nanosheets, nanoplates and nanorods with different compositions and textural characteristics could be obtained. The nanostructures obtained had a positive zeta potential and were characterized by a high specific surface area: 330 m²/g for the AlOOH/FeAl₂ nanosheets; 75 m²/g for the AlOOH/Fe₂O₃/FeAl₂ nanoplates; and 43 m²/g for the Al(OH)₃/FeAl₂ nanorods. The distribution of an FeAl₂ intermetallide over the surface of the AlOOH nanostructures led to an increase in arsenic adsorption of 25% for the AlOOH/FeAl₂ nanosheets and of 34% for the AlOOH/Fe₂O₃/FeAl₂ nanoplates and Al(OH)₃/FeAl₂ nanorods. The adsorption isotherms matched most preciously to the Freundlich model. This fact indicated the energy heterogeneity of the adsorbent surface and multilayer adsorption. The nanostructures studied can be used to purify water contaminated with arsenic.

Performance and Mechanism of As(III/V) Removal from Aqueous Solution by Fe3O4-Sunflower Straw Biochar

Humans and ecosystems are severely damaged by the existence of As(III/V) in the aquatic environment. Herein, an advanced Fe₃O₄@SFBC (Fe₃O₄-sunflower straw biochar) adsorbent was fabricated by co-precipitation method with sunflower straw biochar (SFBC) prepared at different calcination temperatures and different SFBC/Fe mass ratios as templates. The optimal pH for As(III/V) removal was investigated, and Fe₃O₄@SFBC shows removal efficiency of 86.43% and 95.94% for As(III) and As(V), respectively, at pH 6 and 4. The adsorption effect of calcining and casting the biochar-bound Fe₃O₄ obtained at different temperatures and different SFBC/Fe mass ratios were analyzed by batch experiments. The results show that when the SFBC biochar is calcined at 450 °C with an SFBC/Fe mass ratio of 1:5, the adsorption of As(III) and As(V) reaches the maximum, which are 121.347 and 188.753 mg/g, respectively. Fe₃O₄@SFBC morphology, structure, surface functional groups, magnetic moment, and internal morphology were observed by XRD, FTIR, SEM, TEM, and VSM under optimal working conditions. The material shows a small particle size in the range of 12-14 nm with better magnetic properties (54.52 emu/g), which is suitable for arsenic removal. The adsorption mechanism of As(III/V) by Fe₃O₄@SFBC indicates the presence of chemisorption, electrostatic, and complexation. Finally, the material was used for five consecutive cycles of adsorption-desorption experiments, and no significant decrease in removal efficiency was observed. Therefore, the new adsorbent Fe₃O₄@SFBC can be efficiently used for arsenic removal in the aqueous system.

Functionalized biochars: Synthesis, characterization, and applications for removing trace elements from water

Biochar (BC) has been recognized as an effective adsorbent to remove trace elements (TEs) from water. However, low surface functionality and small pore size can limit the adsorption ability of pristine biochar. These limitations can be addressed by using functionalized biochars which are developed by physical, chemical, or biological activation of biochar to improve their physico-chemical properties and adsorption efficiency. Despite the large amount of research concerning functionalized biochars in recent decades, to our knowledge, no comprehensive review of this topic has been published. This review focuses solely on the synthesis, characterization, and applications of functionalized/engineered biochars for removing TEs from water. Firstly, we evaluate the synthesis of functionalized biochars by physical, chemical, and biological strategies that yield the desired properties in the final product. The following section describes the characterization of functionalized biochars using various techniques (SEM, TEM, EDS, XRD, XANES/NEXAFS, XPS, FTIR, and Raman spectroscopy). Afterward, the role of functionalized biochars in the adsorption of different TEs from water/wastewater is critically evaluated with an emphasis on the factors affecting sorption efficiency, sorption mechanisms, fate of sorbed TEs from contaminated environments and associated challenges. Finally, we specifically scrutinized the future recommendations and research directions for the application of functionalized biochar. This review serves as a comprehensive resource for the use of functionalized biochar as an emerging environmental material capable of removing TEs from contaminated water/wastewater.

The Preparation of Eco-Friendly Magnetic Adsorbent from Wild Water Hyacinth (Eichhornia crassipes): The Application for Removing Lead Ions from Industrial Wastewater

Water hyacinth (Eichhornia crassipes) is a wild floating plant that can be found widely in pond or river areas. The plant grows fiercely and causes many harmful issues to the ecosystem around its covered area. This work provides a utilization method that converts wild water hyacinth to reliable magnetic biochar which can be used as a very effective adsorbent for the removal of lead ion Pb(II) in industrial wastewater. The mentioned magnetic biochar can be prepared via a modified pyrolysis process at 550°C with the support of cobalt sulfates as magnetite precursors and limited oxygen from the sweeping gas (the gas mixture ratio is 4 : 1 nitrogen/oxygen). The produced samples were hydrophobic biochar with high oxygen-containing functional groups that are suitable for the removal of inorganic contaminants. The impregnation of cobalt (II, III) oxides provided high magnetic separation performance and additional adsorption sites on the produced magnetic biochar. As indicated by the obtained result, the WHB-Co2M sample possesses a highly porous structure (0.126 cc/g), higher thermal stability (thermal durability reaches 900°C), relatively stable magnetic properties (14.74 emu/g), and a larger surface area (192 m2/g). These beneficial properties led to its suitability to serve as an adsorbent in removing lead ions in the contaminated effluent, recording 95% of removal efficiency and adsorption capacity of 67.815 mg/g. As indicated in the result, all prepared magnetic biochar samples were fitted to two-parameter (Langmuir models) and three-parameter (Sips model) isotherm models. Therefore, the adsorption process in this work could be carried out on both homogeneous and heterogeneous adsorbent surfaces. The adsorption kinetics of the removal process also was described by the pseudo-first-order, pseudo-second-order, and Elovich models to reveal the adsorption and desorption rate of the as-prepared magnetic biochar. This work indicates a successful waste refinery route of converting lignocellulosic biomass such as water hyacinth into value-added material for use as promising heavy metal adsorbents.

Hybrid Metal Oxide/Biochar Materials for Wastewater Treatment Technology: A Review

This paper discusses the properties of metal oxide/biochar systems for use in wastewater treatment. Titanium, zinc, and iron compounds are most often combined with biochar; therefore, combinations of their oxides with biochar are the focus of this review. The first part of this paper presents the most important information about biochar, including its advantages, disadvantages, and possible modification, emphasizing the incorporation of inorganic oxides into its structure. In the next four sections, systems of biochar combined with TiO₂, ZnO, Fe₃O₄, and other metal oxides are discussed in detail. In the next to last section probable degradation mechanisms are discussed. Literature studies revealed that the dispersion of a metal oxide in a carbonaceous matrix causes the creation or enhancement of surface properties and catalytic or, in some cases, magnetic activity. Addition of metallic species into biochars increases their weight, facilitating their separation by enabling the sedimentation process and thus facilitating the recovery of the materials from the water medium after the purification process. Therefore, materials based on the combination of inorganic oxide and biochar reveal a wide range of possibilities for environmental applications in aquatic media purification.

Purification mechanism of city tail water by constructed wetland substrate with NaOH-modified corn straw biochar

The pollution of corn straw to the environment had attracted much attention. The preparation and alkali modification of corn straw biochar as the constructed wetland (CW) substrate was conducive to solving the environment pollution caused by straw and improving the purification effect of CW. The NaOH modification mechanism of corn straw biochar was analyzed by measuring the surface morphology, element content, specific surface area (SSA), pore volume, crystal structure, surface functional groups and CO₂ adsorption. Biochar prepared under relatively optimal NaOH-modified conditions was used as the vertical flow CW substrate to treat city tail water. The results showed that controlling the modification condition of NaOH (< 1.0 mol·L^-1, ≤ 24 h) was conducive to prevent the biochar structure destruction and C element reduction. The SSA and pore volume of NaOH (0.1 mol·L^-1) modified biochar are 360 m²·g^-1 and 0.109 cm³·g^-1, respectively. The biochar adsorption for CO₂ conformed to the Langmuir and Freundlich isothermal adsorption theoretical model (R² > 0.9). The maximum adsorption capacity of CO₂ by modified biochar with NaOH (0.1 mol·L^-1) was 64.516 cm³·g^-1 and increased by 10.3%. The city tail water treated by CW with plants showed that the removal rates of ammonia nitrogen, total nitrogen and nitrate nitrogen reached about 90%. The research results improved the utilization value of straw, realized straw carbon sequestration and promoted the progress of CW technology.

Adsorption of As(III) and As(V) from aqueous solution by magnetic biosorbents derived from chemical carbonization of pea peel waste biomass: Isotherm, kinetic, thermodynamic and breakthrough curve modeling studies

The purpose of this research was to investigate the adsorption of arsenic (As) from aqueous solutions using MPAC-500 and MPAC-600 (magnetic-activated carbons synthesized from the peel of Pisum sativum (pea) pyrolyzed at 500 °C and 600 °C temperatures, respectively). The potential of both biosorbents for As adsorption was determined in batch and column mode. The characterization of both biosorbents was performed by energy dispersive spectroscopy, scanning electron microscope, pHZPC, particle size distribution, X-ray diffraction, zeta potential and Fourier-transform infrared spectroscopy. It was found that the efficiency of MPAC-600 was better than MPAC-500 for the adsorption of As(III) and As(V) ions. The adsorption capacities of MPAC-500 and MPAC-600 in removing As(III) were 0.7297 mg/g and 1.3335 mg/g, respectively, while the values of Qmax for As(V) on MPAC-500 and MPAC-600 were 0.4930 mg/g and 0.9451 mg/g, respectively. The Langmuir isotherm model was found to be the best fit for adsorption of As(III) by MPAC-500 and MPAC-600, as well as adsorption of As(V) by MPAC-500. The Freundlich isotherm model, on the other hand, was optimal for As(V) removal with MPAC-600. With R2 values close to unity, the pseudo-second-order kinetics were best fitted to the adsorption process of both As species. The Thomas model was used to estimate the breakthrough curves. The effects of coexisting oxyanions and regeneration studies were also carried out to examine the influence of oxyanions on As adsorption and reusability of biosorbents.

Fabrication, application, and mechanism of metal and heteroatom co-doped biochar composites (MHBCs) for the removal of contaminants in water: A review

The potential risk of various contaminants in water has recently attracted public attention. Biochars and modified biochars have been widely developed for environmental remediation. Metal and heteroatom co-doped biochar composites (MHBCs) quickly caught the interest of researchers with more active sites and higher affinity for contaminants compared to single-doped biochar by metal or heteroatoms. This study provides a comprehensive review of MHBCs in wastewater decontamination. Firstly, the main fabrication methods of MHBCs were external doping and internal doping, with external doping being the most common. Secondly, the applications of MHBCs as adsorbents and catalysts in water treatment were introduced emphatically, which mainly included the removal of metals, antibiotics, dyes, pesticides, phenols, and other organic contaminants. Thirdly, the removal mechanisms of contaminants by MHBCs were deeply discussed in adsorption, oxidation and reduction, and degradation. Furthermore, the influencing factors for the removal of contaminants by MHBCs were also summarized, including the physicochemical properties of MHBCs, and environmental variables of pH and co-existing substance. Finally, futural challenges of MHBCs are proposed in the leaching toxicity of metal from MHBCs, the choice of heteroatoms on the fabrication for MHBCs, and the application in the composite system and soil remediation.

Research Progress on Adsorption of Arsenic from Water by Modified Biochar and Its Mechanism: A Review

Arsenic (As) is a non-metallic element, which is widely distributed in nature. Due to its toxicity, arsenic is seriously harmful to human health and the environment. Therefore, it is particularly important to effectively remove arsenic from water. Biochar is a carbon-rich adsorption material with advantages such as large specific surface area, high porosity, and abundant functional groups, but the original biochar has limitations in application, such as limited adsorption capacity and adsorption range. The modified biochar materials have largely enhanced the adsorption capacity of As in water due to their improved physicochemical properties. In this review, the changes in the physicochemical properties of biochar before and after modification were compared by SEM, XRD, XPS, FT-IR, TG, and other characterization techniques. Through the analysis, it was found that the adsorbent dosage and pH are the major factors that influence the As adsorption capacity of the modified biochar. The adsorption process of As by biochar is endothermic, and increasing the reaction temperature is conducive to the progress of adsorption. Results showed that the main mechanisms include complexation, electrostatic interaction, and precipitation for the As removal by the modified biochar. Research in the field of biochar is progressing rapidly, with numerous achievements and new types of biochar-based materials prepared with super-strong adsorption capacity for As. There is still much space for in-depth research in this field. Therefore, the future research interests and applications are put forward in this review.

Preparation of bamboo-derived magnetic biochar for solid-phase microextraction of fentanyls from urine

In this study, a biochar-based magnetic solid-phase microextraction method, coupled with liquid chromatography-mass spectrometry (LC/MS), was developed for analyzing fentanyl analogs from urine sample. Magnetic biochar was fabricated through an one-step pyrolysis carbonization and magnetization process, followed by an alkali treatment. In order to achieve desired extraction efficiency, feed stocks (wood and bamboo) and different pyrolysis temperatures (300-700 °C) were optimized. The magnetic bamboo biochar pyrolyzed at 400°C was found to have the greatest potential for extraction of fentanyls, with enrichment factors ranging from 58.9 to 93.7, presumably due to H-bonding and π- π interactions between biochar and fentanyls. Various extraction parameters, such as type and volume of desorption solvent, pH, extraction time were optimized, respectively, to achieve the highest extraction efficiency for the target fentanyls. Under optimized conditions, the developed method was found to have detection limits of 3.1-9.4 ng/L, a linear range of 0.05-10 μg/L, good precisions (1.9-9.4% for intra-batch, 2.9-9.9% for inter-batch), and satisfactory recoveries (82.0-111.3%). The developed method by using magnetic bamboo biochar as adsorbent exhibited to be an efficient and promising pretreatment procedure and could potentially be applied for drug analysis in biological samples. This article is protected by copyright. All rights reserved.

Adsorption of Arsenic on Fe-Modified Biochar and Monitoring Using Spectral Induced Polarization

This work demonstrates the potential of Fe-modified biochar for the treatment of arsenic (As) simulated wastewater and the monitoring of adsorption in real-time. Specifically, we propose the utilization of date-palm leaves for the production of biochar, further modified with Fe in order to improve its adsorption function against inorganic pollutants, such as As. Both the original biochar and the Fe-modified biochar were used for adsorption of As in laboratory batch and column experiments. The monitoring of the biochar(s) performance and As treatment was also enhanced by using the spectral induced polarization (SIP) method, offering real-time monitoring, in addition to standard chemical monitoring. Both the original and the Fe-modified biochar achieved high removal rates with Fe-modified biochar achieving up to 98% removal of As compared to the 17% by sand only (control). In addition, a correlation was found between post-adsorption measurements and SIP measurements.

Zirconium hydroxide nanoparticle encapsulated magnetic biochar composite derived from rice residue: Application for As(III) and As(V) polluted water purification

Finding a low-cost and suitable adsorbent is still in urgent need for efficient decontamination of As(III) and As(V) elements from the polluted waters. A novel zirconium hydroxide nanoparticle encapsulated magnetic biochar composite (ZBC) derived from rice residue was synthesized for the adsorptive capture of As(III) and As(V) from aqueous solutions. The results revealed that ZBC showed an acceptable magnet separation ability and its surface was encapsulated with lots of hydrous zirconium oxide nanoparticles. Compared to As(III), the adsorption of As(V) onto ZBC was mainly dependent on the pH of the solution. The intraparticle diffusion model described the adsorption process. ZBC showed satisfactory adsorption performances to As(III) and As(V) with the highest adsorption quantity of 107.6 mg/g and 40.8 mg/g at pH 6.5 and 8.5, respectively. The adsorption of As(III) and As(V) on ZBC was almost impervious with the ionic strength while the presence of coexisting ions, especially phosphate, significantly affected the adsorption process. The processes of complexation reaction and electrostatic attraction contributed to the adsorption of As(III) and As(V) onto ZBC. ZBC prepared from kitchen rice residue was found to be a low cost environmentally friendly promising adsorbent with high removal capacity for As(III) and As(V) and could be recycled easily from contaminated waters.

Obtention of biochar-Fe/Ce using Punica granatum with high adsorption of ampicillin capacity

This research presents the obtaining of a biochar (CB) from the use of pomegranate peel (Punica granatum) conditioned with iron and cerium nanoparticles (C-Fe/Ce), as well as its characterization by SEM (Scanning Electronic Microscopy), FTIR (Fourier Transform Infrared Spectrometry), TGA (Thermogravimetric analysis), EDS (Energy Dispersive Spectroscopy), XPS (X-Ray Photoelectron Spectroscopy) and evaluation of the adsorption capacity of ampicillin (AMP) in aqueous phase at 20, 30 and 40 °C. The maximum adsorption capacity for CB was 18.97 mg g-1 and for C-Fe/Ce, 27.61 mg g-1 at pH of 7, observing that with increasing temperature, the sorption capacity decreases in both materials, the experimental data was fitted to various mathematical models and the best fit was the pseudo-second order model for the kinetics, whilst for the adsorption isotherms the best fit was with the Langmuir model, indicating that the adsorption process is carried out in a monolayer on a homogeneous surface, through a chemisorption process. According to the thermodynamic parameters this process is carried out through an exothermic reaction. The results obtained indicate that both materials are suitable for the removal of AMP in the aqueous phase and that they can be reused up to 5 times.

Efficient removal arsenate from water by biochar-loaded Ce3+-enriched ultra-fine ceria nanoparticles through adsorption-precipitation

Biochar-loaded Ce³⁺-enriched ultra-fine ceria nanoparticles (Ce-BC) were used as a novel nanostructured adsorbent for the removal of arsenate (As(V)) from aqueous solutions. The effect of cerium valence on As(V) adsorption and the mechanism of As(V) adsorption onto Ce-BC were investigated using batch experiments and a series of spectroscopy detection technologies. The adsorption isotherm data fitted with the Langmuir model, with maximum As(V) sorption capacity of 219.8 mg g^-1 at pH 5.0 and 25 °C. The adsorption kinetics fitted well with the pseudo-second-order model. Ce³⁺ on the surface of Ce-BC plays an important role in the adsorption of As(V). The decrease in Ce³⁺ concentration from 60.1% to 48.9% on the Ce-BC surface, significantly decreased the adsorption of As(V) on Ce-BC. Furthermore, a strong affinity between As(V) and Ce³⁺-enriched Ce-BC was revealed, resulting in irreversible adsorption. Most importantly, the adsorbed As(V) could further react with Ce³⁺ of the ultra-fine cerium oxide nanoparticles in Ce-BC to form rod-like CeAsO₄ precipitates. Through the novel adsorption-precipitation process, Ce-BC can be used to remove trace As(V).

Interactive effects of biochar and mussel shell activated concoctions on immobilization of nickel and their amelioration on the growth of rapeseed in contaminated aged soil

Mussel shell (MS) and biochar (BC) are commonly used for the remediation of metal contaminated soil. However, less research has been focused to examine the efficacy of their combinations to reduce metal toxicity in crop plants. This study was therefore conducted to investigate the effects of BC, MS and their activated concoctions on the soil properties, enzyme activities and nickel (Ni) immobilization in aged Ni contaminated soil. Moreover, the growth, photosynthetic pigments and anti-oxidative machnery of Brassica napus plants has also been investigated in order to determine amendments efficiency in reducing soil Ni toxicity for plants. The results showed that the application of Ni adversely affected soil health and trigged stress responses by inducing oxidative stress in B. napus. However, the incorporation of amendments reduced the bioavailability of Ni, and the concoctions of BC and MS showed promising results in the immobilization of Ni. Among various combinations of BC and MS, treatment with BC + MS (3:1) significantly reduced Ni uptake, decreased reactive oxygen species (ROS) and enhanced antioxidant defense of B. napus plants. Results showed that amendment's combinations stimulated the transcriptional levels of ROS scavenging enzymes and suppressed the expression level of Ni transporters. The morphological and physical characterization techniques (i.e. SEM, BET, EDS, FTIR and X-ray diffraction analyses) showed that amendment's combinations had relatively higher Ni adsorption capacity, indicating that BC and MS concoctions are efficient immobilizing agents for minimizing Ni availability, preventing oxidative toxicity and promoting growth and biomass production in rapeseed plants under metal stress conditions.

Performance of a novel iron infused biochar developed from Raphanus sativus and Artocarpus heterophyllus refuse for trivalent and pentavalent arsenic adsorption from an aqueous solution: mechanism, isotherm and kinetics study

Fabrication of magnetic biochar was done by pyrolysis of waste leaves of Raphanus sativus (MRB) and Artocarpus heterophyllus (MJB) peel pretreated with FeCl₃ was examined for As(III and V) adsorption from an aqueous solution. The synthesized bioadsorbents were characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), particle size analysis (PSA), scanning electron microscope (SEM), energy dispersive x-ray (EDX), zeta potential, Vibrating sample magnetometer (VSM) and point of zero charge (pH_ZPC). MRB-800 exhibits greater efficiency toward the removal of both As species with q_max value 2.08 mg/g for As(III) and 2.03 mg/g for As(V). Whereas, the q_max value was 1.13 mg/g for As (III) and 1.26 mg g^-1 for As (V) adsorption using MJB-800. Temkin and Freundlich isotherm were best fitted to the adsorption of As(III) and As(V) by MRB-800, respectively. Langmuir isotherm was best followed to the adsorption of As (III and V) by MJB-800. Pseudo-second-order kinetics was well simulated by the experimental data of As adsorption using both the bioadsorbents. Surface complexation and electrostatic attraction was dominant mechanism for As (III) and As (V) adsorption. Thermodynamic study shows that removal of As (III) was exothermic while the As (V) adsorption was endothermic for MRB-800 and MJB-800.

Differentiating Nanomaghemite and Nanomagnetite and Discussing Their Importance in Arsenic and Lead Removal from Contaminated Effluents: A Critical Review

Arsenic and lead heavy metals are polluting agents still present in water bodies, including surface (lake, river) and underground waters; consequently, the development of new adsorbents is necessary to uptake these metals with high efficiency, quick and clean removal procedures. Magnetic nanoparticles, prepared with iron-oxides, are excellent candidates to achieve this goal due to their ecofriendly features, high catalytic response, specific surface area, and pulling magnetic response that favors an easy removal. In particular, nanomagnetite and maghemite are often found as the core and primary materials regarding magnetic nanoadsorbents. However, these phases show interesting distinct physical properties (especially in their surface magnetic properties) but are not often studied regarding correlations between the surface properties and adsorption applications, for instance. Thus, in this review, we summarize the main characteristics of the co-precipitation and thermal decomposition methods used to prepare the nano-iron-oxides, being the co-precipitation method most promising for scaling up processes. We specifically highlight the main differences between both nano-oxide species based on conventional techniques, such as X-ray diffraction, zero and in-field Mössbauer spectroscopy, X-ray photoelectron spectroscopy, X-ray absorption spectroscopy, and X-ray magnetic circular dichroism, the latter two techniques performed with synchrotron light. Therefore, we classify the most recent magnetic nanoadsorbents found in the literature for arsenic and lead removal, discussing in detail their advantages and limitations based on various physicochemical parameters, such as temperature, competitive and coexisting ion effects, i.e., considering the simultaneous adsorption removal (heavy metal-heavy metal competition and heavy metal-organic removal), initial concentration, magnetic adsorbent dose, adsorption mechanism based on pH and zeta potential, and real water adsorption experiments. We also discuss the regeneration/recycling properties, after-adsorption physicochemical properties, and the cost evaluation of these magnetic nanoadsorbents, which are important issues, but less discussed in the literature.

Ethylenediamine and Pentaethylene Hexamine Modified Bamboo Sawdust by Radiation Grafting and Their Adsorption Behavior for Phosphate

Phosphate is an important component for the growth of plants and microorganisms; however, excess phosphate causes serious eutrophication in natural waters. New potential low-loss adsorbents from natural biomass for phosphate removal are desired. Bamboo is one of the most abundant renewable cellulose resources; however, the pure bamboo cellulose is poor to adsorb phosphate. To enhance the adsorption capacity, in this work, bamboo sawdust (BS) was chemically modified by two kinds of amines. First, glycidyl methacrylate (GMA) was grafted on BS using radiation induced graft polymerization. Then, the GMA-grafted BS was further modified by a ring-opening reaction with amines, including ethylenediamine (EDA) and pentaethylene hexamine (PEHA). The amine groups were then quaternized to prepare the BS-GMA-EDA-Q and BS-GMA-PEHA-Q adsorbents. The adsorbents were characterized by FTIR, SEM, TG, and XPS analysis. The adsorption performances of the adsorbents for phosphate were evaluated through batch experiments. The adsorption by BS-GMA-EDA-Q and BS-GMA-PEHA-Q both well obeyed the pseudo-second-order kinetic model and the Langmuir isotherm model, indicating that the adsorption process was chemical monomolecular layer adsorption. The maximum adsorption capacities for BS-GMA-EDA-Q and BS-GMA-PEHA-Q calculated by the Langmuir model were 85.25 and 152.21 mg/g, respectively. A total of 1 mol/L HCl was used to elute the saturated adsorbents. A negligible decrease in adsorption capacity was found after five adsorption–desorption cycles.

Organic and inorganic amendments for the remediation of nickel contaminated soil and its improvement on Brassica napus growth and oxidative defense

In-situ stabilization has been considered an effective way to remediate metal contaminated soil. Thus, pot experiments were undertaken to investigate the effectiveness of multiple stabilization agents such as biochar (BC), mussel shell (MS), zeolite (ZE) and limestone (LS) on the immobilization of Ni, physicochemical features and enzyme activities in polluted soil. Results showed that the sole application of Ni adversely affected the rapeseed growth, photosynthetic pigments, and antioxidative defense. However, the addition of amendments to the contaminated soil significantly reduced Ni bioavailability. The XRD analysis confirmed the formation of Ni related ligands and FTIR showed the presence of hydroxyl, carboxyl and sulfur functional groups, as well as complexation and adsorption of Ni on amendments. Among multiple amendments, biochar significantly enhanced plant biomass attributes and total chlorophyll content. Moreover, addition of amendments also strengthened the antioxidant defense by decreasing Ni induced oxidative stress (H₂O₂ and O₂^.-), increased macronutrient availability, reduced Ni uptake and improved soil health. The qPCR analysis showed that the Ni transporters were significantly suppressed by amendments, which is correlated with the lower accumulation of Ni in rapeseed. The present study showed that immobilizing agents, especially biochar, is an effective amendment to immobilize Ni in soil, which restricts its entry into the food chain.

Reduction and removal of As(Ⅴ) in aqueous solution by biochar derived from nano zero-valent-iron (nZVI) and sewage sludge

Biochar prepared by co-pyrolysis of nano-zero-valent iron and sewage sludge (nZVISB) was used to remove As(Ⅴ) from aqueous solution. When the initial pH was 2, the initial As(Ⅴ) concentration was 20 mg L^-1, the dose of nZVISB was 10 g L^-1, the contact time was 24 h, and the adsorption temperature was 298K, the removal efficiency of As(Ⅴ) was greater than 99%. The isothermal removal of As(Ⅴ) followed the Freundlich model better, and the maximum adsorption capacity of As(Ⅴ) was 60.61 mg g^-1. The removal process of As(Ⅴ) could be better described by pseudo-second-order kinetic model, and the rate-controlling step should be liquid film diffusion and chemical reaction. Thermodynamic analysis indicated that the removal of As(Ⅴ) was a spontaneous and endothermic process dominated by chemical adsorption. The characterizations of nZVISB before/after adsorption and the solution after adsorption suggested that the iron-containing substances (Fe⁰, Fe²⁺, FeOOH) and organics in the nZVISB had a great effect on the removal of As(Ⅴ), and the As was mainly immobilized on nZVISB by speciation of As-O-Fe.

Preparation of magnetic biochar and its application in catalytic degradation of organic pollutants: A review

In recent years, magnetic biochar (MBC) has been greatly concerned because of its magnetic separation characteristics, and has been successfully used as a catalyst in the catalytic degradation of organic pollutants. However, there is currently a lack of a more systematic summary of MBC preparation methods, and no detailed overview of the catalytic mechanism of MBC catalysts for the degradation of organic pollutants. Therefore, we carry out this work to fill the above gaps. At first, we summarize the raw materials, preparation methods, and types of MBC in detail, and emphasize the MBC prepared by iron-containing sludge. Then, the catalytic mechanisms of MBC in peroxydisulfate, peroxymonosulfate, Fenton-like, photocatalysis, and NaBH₄ systems are carefully summarized, highlighting the contribution of various parts of MBC in catalysis. The degradation efficiency of organic pollutants in the above systems is evaluated. Finally, the stability and reusability of MBC catalysts are evaluated. In conclusion, this review contributes a meager force to the future development of MBC.

High capacity aqueous phosphate reclamation using Fe/Mg-layered double hydroxide (LDH) dispersed on biochar

Phosphate is a primary plant nutrient, serving integral role in environmental stability. Excessive phosphate in water causes eutrophication; hence, phosphate ions need to be harvested from soil nutrient levels and water and used efficiently. Fe-Mg (1:2) layered double hydroxides (LDH) were chemically co-precipitated and widely dispersed on a cheap, commercial Douglas fir biochar (695 m²/g surface area and 0.26 cm³/g pore volume) byproduct from syn gas production. This hybrid multiphase LDH dispersed on biochar (LDHBC) robustly adsorbed (~5h equilibrium) phosphate from aqueous solutions in exceptional sorption capacities and no pH dependence between pH 1-11. High phosphate Langmuir sorption capacities were found for both LDH (154 to 241 mg/g) and LDH-modified biochar (117 to 1589 mg/g). LDHBC was able to provide excellent sorption performance in the presence of nine competitive anion contaminants (CO₃^2-, AsO₄^3-, SeO₄^2-, NO₃^-, Cr₂O₇^2-, Cl^-, F^-, SO₄^2-, and MoO₄^2-) and also upon remediating natural eutrophic water samples. Regeneration was demonstrated by stripping with aqueous 1 M NaOH. No dramatic performance drop was observed over 3 sorption-stripping cycles for low concentrations (5 ppm). The adsorbents and phosphate-laden adsorbents were characterized using Elemental analysis, BET, PZC, TGA, DSC, XRD, SEM, TEM, and XPS. The primary sorption mechanism is ion-exchange from low to moderate concentrations (10-500 ppm). Chemisorption and stoichiometric phosphate compound formation were also considered at higher phosphate concentrations (>500 ppm) and at 40 °C. This work advances the state of the art for environmentally friendly phosphate reclamation. These phosphate-laden adsorbents also have potential to be used as a slow-release phosphate fertilizer.

Enhanced arsenate removal by Fe-impregnated canola straw: assessment of XANES solid-phase speciation, impacts of solution properties, sorption mechanisms, and evolutionary polynomial regression (EPR) models

The impact of arsenic (As) contamination of water is an ongoing concern worldwide with As released from anthropogenic activities including mining and agriculture. Biosorption is a promising As treatment methodology used currently for arsenate (As(V)) sorption from water. The biosorbent was developed by a simple and inexpensive treatment of coating of canola straw particles with iron hydroxides. The modification procedure was optimized with consideration of the concentration of iron solution, pH of modification process, and sonication time. A higher concentration of iron and lower pH led to an improved sorption capacity of the iron-loaded canola straw (ICS), while impacts of sonication time were not conclusive. Pareto analyses indicated that the magnitude of the effect of the pH was higher than that of the iron concentration. Overall, the maximum As(V) sorption capacity of the ICS was 5.5 mg/g for an 0.25 M FeCl₃ solution concentration at pH 3. Analysis of kinetic data showed that the sorption processes of As(V) followed pseudo-second order and Elovich mechanisms, while sorption isotherm data were best represented by Freundlich and Temkin isotherm models. Studying the effect of ionic strength using NaCl suggested that the inner-sphere complex was the probable sorption mechanism. The thermodynamic parameters including ΔS°, ΔH°, and ΔG° showed that the As(V) sorption was thermodynamically favorable and spontaneous. Arsenic K-edge X-ray absorption near edge structure (XANES) spectroscopy indicated that no reaction to As(III) occurred during the sorption of As(V) using the optimum ICS biosorbent. The evolutionary polynomial regression (EPR) approach was able to closely match predicted vs. experimental sorption capacities (R² = 0.95). Overall, the improved understanding of the biosorbent's capability for removal of As(V) will be beneficial for assessment of its use for treatment of various water and wastewater matrices. In addition, knowledge gained from this research can assist in the understanding of sorption capacities of a variety of other biosorbents.

Evaluation of zeolite, nanomagnetite, and nanomagnetite-zeolite composite materials as arsenic (V) adsorbents in hydroponic tomato cultures

There is a growing interest in the use of adsorbent nanoparticles to mitigate the toxic effects of pollutants in natural matrices. However, due to their small size, nanoparticles have the potential to transport and disseminate contaminants adsorbed on their surfaces into environmental compartments with greater risk to human, animal, or plant health. This potential consequence of nanoparticle application remains largely unstudied. Here, we studied the application of three adsorbents, including zeolite (Z, micrometric size), nanomagnetite (Mt), and a nanomagnetite-zeolite composite (MtZ) intended to mediate arsenic toxicity in hydroponic tomato cultures. Adsorption studies showed an arsenate adsorption sequence of MtZ (6.2 mg g^-1) ≥ Mt (4.7 mg g^-1) ≫ Z (0.3 mg g^-1). Tomatoes grown under the Mt condition demonstrated the lowest growth rate (4.2 cm), corresponding to a 45% decrease compared to the control (7.6 cm), as well as the highest oxidative stress level (0.024 μmol g^-1) as indicated by malondialdehyde (MDA) concentration, almost twice the control (0.014 μg g^-1). Tomatoes grown under MtZ conditions showed a 22% decreased growth (5.9 cm) but MDA levels (0.012 μmol g^-1) were comparable to the control. Together, these results suggest that Mt at the nanometric size could obstruct channels in the plant and prevent absorption of water and nutrients. Anchoring nanomaterials in larger composites of micrometer size presents a promising alternative that would retain their super-adsorbent properties while avoiding toxicity due to nanometric size.

Hydrochar and pyrochar for sorption of pollutants in wastewater and exhaust gas: A critical review

Pollutants in wastewater and exhaust gas bring out serious concerns to public health and the environment. Biochar can be developed as a sustainable adsorbent originating from abundant bio-wastes, such as agricultural waste, forestry residue, food waste and human waste. Here we highlight the state-of-the-art research progress on pyrochar and hydrochar for the sorption of pollutants (heavy metal, organics, gas, etc) in wastewater and exhaust gases. The adsorption performance of pyrochar and hydrochar are compared and discussed in-depth, including preparation procedures (carbonization and activation), sorption possible mechanisms, and physiochemical properties. Challenges and perspective for designing efficient and environmental benign biochar-based adsorbents are finally addressed.

N-Alkylated chitosan coupled to the liquid-phase polymer-based retention (LPR) technique to remove arsenic (V) from aqueous systems

Water-soluble polymer based on alkylated chitosan with a quaternary ammonium group (Ch-QAG) was prepared, characterized, and applied to remove arsenate ions from aqueous solution by LPR technique. The arsenic removal was performed by the washing method (WM) and enrichment method (EM). Through the WM, studies of the pH and variation in the concentrations of interferents and arsenate ions were carried out. The effect of the removal of arsenate ions in simulated water was determined from the Camarones River in northern Chile. Ch-QAG showed high affinity for binding arsenate species (99% of removal) at pH 11.0 at a molar ratio of 20:1 polymer: As(V). High selectivity was also observed in the presence of interfering ions such as Cl^-, SO₄^2-, and PO₄^3-, resulting in a removal rate over 80% at percentages over 95% for a concentration of 100 mg L^-1 of As (V). The maximum retention capacity obtained was 112, 105, and 98 mg g^-1 for three load cycles. The retention percentage for simulated water was 46.3% at a concentration of 1300 μ g L^-1. In conclusion, the results presented in this study show that using Ch-QAG with ultrafiltration membranes is a great alternative to remove As (V) at high removal rates.

Treatment of aqueous arsenic - A review of biochar modification methods

Arsenic (As) is an ever-present worldwide environmental contamination issue. The process of As sorption for treatment of contaminated waters is regarded as a promising treatment technology approach due to its simplicity and potential for high efficiency. Biochars are carbon-rich porous solids produced by heating of biomasses under low oxygen conditions. Biochars are considered to be environmentally friendly sorbents that can be used to treat various As-containing waters. However, unmodified biochar is generally a poor sorbent for As species due to static repulsion between the As oxyanions and the negatively charged biochar surface. The As sorption capacity of biochars can be substantially improved by treatments using various physical and chemical activation and modification methods. Thus, this review includes 63 research studies using physical and chemical approaches to enhance biochar physicochemical structures and As sorption efficiencies. The effectiveness of each method for altering the characteristics and sorption capacity of biochars is described. This review can help to focus the scope of future As biochar sorption studies and aid researchers in optimization of biochar-based sorbents for As treatment.