Zinc removal and recovery from industrial wastewater with a microbial fuel cell: Experimental investigation and theoretical prediction

Electrochemically active biofilms responses to gadolinium stress during wastewater treatment in bioelectrochemical systems

Gadolinium-based contrast agents used in magnetic resonance imaging (MRI) contribute to increasing gadolinium(III) [Gd(III)] concentrations in aquatic environments, as conventional wastewater treatment plants lack effective removal mechanisms. This study investigated the potential of single-chamber microbial fuel cells (SCMFCs) for Gd(III) removal, focusing on removal efficiency and the physiological responses of electrochemically active biofilms. SCMFCs demonstrated exceptional Gd(III) removal efficiency exceeding 99.75 ± 0.007 % across various initial concentrations (10-60 mg/L). Power output and chemical oxygen demand (COD) removal efficiency showed dose-dependent responses to Gd(III) stress, with maximum power output decreasing from 479.56 mV to 260.43 mV as Gd(III) increased from 0 to 60 mg/L. COD removal efficiency declined from 96.49 ± 1.2 % to 90.23 ± 1.6 % over the same range. Microbial community analysis revealed selective enrichment of exoelectrogens at lower Gd(III) concentrations, with Geobacter relative abundance decreasing from 11.14 % to 1.82 %. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) analyses demonstrated that elevated Gd(III) concentrations reduced electrochemically active bacterial colonization in anode biofilms. Fourier-transform infrared spectroscopy (FTIR) identified specific functional groups associated with Gd(III) biosorption, while predictive functional profiling indicated upregulation of metal resistance genes under Gd(III) exposure. These findings demonstrate the effectiveness of SCMFCs in Gd(III) removal from wastewater while elucidating microbial adaptation mechanisms to rare earth element exposure, providing insights for developing sustainable treatment solutions for emerging contaminants.

Electrode functional microorganisms in bioelectrochemical systems and its regulation: A review

Bioelectrochemical systems (BES) as environmental remediation biotechnologies have boomed in the last two decades. Although BESs combined technologies with electro-chemistry, -biology, and -physics, microorganisms and biofilms remain at their core. In this review, various functional microorganisms in BESs for CO2 reduction, dehalogenation, nitrate, phosphate, and sulfate reduction, metal removal, and volatile organic compound oxidation are summarized and compared in detail. Moreover, interrelationship regulation approaches for functional microorganisms and methods for electroactive biofilm development, such as targeted electrode surface modification, chemical treatment, physical revealing, biological optimization, and genetic programming are pointed out. This review provides promising guidance and suggestions for the selection of microbial inoculants and provides an analysis of the role of individual microorganisms in mixed microbial communities and its metabolisms.

Enhancement of Zn adsorption on coal fly ash-based geopolymer with steel slag incorporation: Leaching behavior and performance insights

Industrial solid wastes like coal fly ash (CFA) and steel slag pose environmental challenges, while the remediation of heavy metal-contaminated water remains a global priority. This study investigates the impact of incorporating steel slag during the synthesis of CFA-based geopolymers (CFAG) on the leaching characteristics of inherent heavy metals in CFA and the Zn adsorption performance of CFAG. Leaching experiments show geopolymerization effectively immobilizes heavy metals including Fe, Cr, As, Cd, and Ti in CFA while having little effect on Mn, V, and Ni. The incorporation of 10 wt% steel slag into CFAG further enhances the stability of As but slightly elevates the release of Fe, Ti, Cu, V, and Cd. Column experiments demonstrate steel slag doped-CFAG (SCG) achieves over a 50% improvement in Zn adsorption performance compared to CFAG. Furthermore, hydrochemical analysis, X-ray absorption spectroscopy, and sequential desorption experiments reveal Zn is removed from solution by SCG primarily through surface complexation and precipitation as ZnSiO4, which have suitable stability and resistance to desorption. These findings suggest doping steel slag into CFAG is a viable strategy to enhance Zn removal in contaminated water, decrease remediation costs, and effectively consume CFA and steel slag. Nevertheless, potential trade-offs concerning heavy metal leaching should be carefully evaluated to balance the performance and environmental impacts of SCG.

Assessing the pollution and ecotoxicological status of the Iguaçu River, southern Brazil: A review

The degradation of water resources available for human consumption is increasing with the continuous release of chemicals into aquatic environments and their inefficient removal in wastewater treatment. Several watersheds in Brazil, such as the Iguaçu River, are affected by multiple sources of pollution and lack information about their pollution status. The Iguaçu River basin (IRB) has great socioeconomic and environmental relevance to both the supply of water resources and its considerable hydroelectric potential, as well as for the high rate of endemism of its ichthyofauna. Also, the IRB is home to large conservation units, such as the Iguaçu National Park, recognized by UNESCO as a natural World Heritage Site. Thus, this article discusses the chemical pollution in the IRB approaching: (i) the main sources of pollution; (ii) the occurrence of inorganic and organic micropollutants; (iii) the available ecotoxicological data; and (iv) the socioeconomic impacts in three regions of the upper, middle, and lower IRB. Different studies have reported relevant levels of emerging contaminants, persistent organic pollutants, toxic metals, and polycyclic aromatic hydrocarbons detected in the water and sediment samples, especially in the upper IRB region, associated with domestic and industrial effluents. Additionally, significant concentrations of pesticides and toxic metals were also detected in the lower IRB, revealing that agricultural practices are also relevant sources of chemicals for this watershed. More recently, studies indicated an association between fish pathologies and the detection of micropollutants in the water and sediments in the IRB. The identification of the main sources of pollutants, associated with the distribution of hazardous chemicals in the IRB, and their potential effects on the biota, as described in this review, represent an important strategy to support water management by public authorities for reducing risks to the local endemic biodiversity and exposed human populations. Integr Environ Assess Manag 2024;20:1280-1305. © 2023 SETAC.

Biofilm electrode reactor coupled manganese ore substrate up-flow microbial fuel cell-constructed wetland system: High removal efficiencies of antibiotic, zinc (II), and the corresponding antibiotic resistance genes

A coupled system comprised of a biofilm electrode reactor (BER) and a manganese ore substrate microbial fuel cell-constructed wetland (MFC-CW) system was used to remove co-exposed antibiotic and Zn (II), as well as simultaneously reduce copies of antibiotic resistance genes (ARGs) in the current study. In this system, BER primarily reduced the concentrations of antibiotics and Zn (II), and the effluent was used as the input to the MFC-CW, thereby providing electricity to BER. Co-exposure to a high concentration of Zn (II) decreased the relative abundances (RAs) of ARGs in the BER effluent, whereas the remaining sub-lethal concentration of Zn (II) increased the RAs of ARGs in the MFC-CW effluent. Even though the absolute copies of ARGs in the effluents increased during co-exposure, the total number of target ARG copies in the effluent of MFC-CW was significantly lower than that of BER. Moreover, BER pre-treatment eliminated most of Zn (II), which improved the electrical power generation characteristic of the MFC-CW unit. Correspondingly, the bacterial community and the ARGs hosts were analyzed to demonstrate the mechanism. In conclusion, the coupled system demonstrates significant potential to reduce antibiotics, Zn (II) and environmental risks posed by ARGs.

A mini-review on indigenous microbial biofilm from various wastewater for heavy-metal removal - new trends

Biofilm, as a form of the microbial community in nature, represents an evolutionary adaptation to the influence of various environmental conditions. In nature, the largest number of microorganisms occur in the form of multispecies biofilms. The ability of microorganisms to form a biofilm is one of the reasons for antibiotic resistance. The creation of biofilms resistant to various contaminants, on the other hand, improves the biological treatment process in wastewater treatment plants. Heavy metals cannot be degraded, but they can be transformed into non-reactive and less toxic forms. In this process, microorganisms are irreplaceable as they interact with the metals in a variety of ways. The environment polluted by heavy metals, such as wastewater, is also a source of undiscovered microbial diversity and specific microbial strains. Numerous studies show that biofilm is an irreplaceable strategy for heavy metal removal. In this review, we systematize recent findings regarding the bioremediation potential of biofilm-forming microbial species isolated from diverse wastewaters for heavy metal removal. In addition, we include some mechanisms of action, application possibilities, practical issues, and future prospects.

Zinc recovery from bioleachate using a microbial electrolysis cell and comparison with selective precipitation

Metal recycling is essential for strengthening a circular economy. Microbial leaching (bioleaching) is an economical and environmentally friendly technology widely used to extract metals from insoluble ores or secondary resources such as dust, ashes, and slags. On the other hand, microbial electrolysis cells (MECs) would offer an energy-efficient application for recovering valuable metals from an aqueous solution. In this study, we investigated a MEC for Zn recovery from metal-laden bioleachate for the first time by applying a constant potential of -100 mV vs. Ag/AgCl (3 M NaCl) on a synthetic wastewater-treating bioanode. Zn was deposited onto the cathode surface with a recovery efficiency of 41 ± 13% and an energy consumption of 2.55 kWh kg-1. For comparison, Zn recovery from zinc sulfate solution resulted in a Zn recovery efficiency of 100 ± 0% and an energy consumption of 0.70 kWh kg-1. Furthermore, selective metal precipitation of the bioleachate was performed. Individual metals were almost completely precipitated from the bioleachate at pH 5 (Al), pH 7 (Zn and Fe), and pH 9 (Mg and Mn).

Toxicity of Heavy Metals and Recent Advances in Their Removal: A Review

Natural and anthropogenic sources of metals in the ecosystem are perpetually increasing; consequently, heavy metal (HM) accumulation has become a major environmental concern. Human exposure to HMs has increased dramatically due to the industrial activities of the 20th century. Mercury, arsenic lead, chrome, and cadmium have been the most prevalent HMs that have caused human toxicity. Poisonings can be acute or chronic following exposure via water, air, or food. The bioaccumulation of these HMs results in a variety of toxic effects on various tissues and organs. Comparing the mechanisms of action reveals that these metals induce toxicity via similar pathways, including the production of reactive oxygen species, the inactivation of enzymes, and oxidative stress. The conventional techniques employed for the elimination of HMs are deemed inadequate when the HM concentration is less than 100 mg/L. In addition, these methods exhibit certain limitations, including the production of secondary pollutants, a high demand for energy and chemicals, and reduced cost-effectiveness. As a result, the employment of microbial bioremediation for the purpose of HM detoxification has emerged as a viable solution, given that microorganisms, including fungi and bacteria, exhibit superior biosorption and bio-accumulation capabilities. This review deals with HM uptake and toxicity mechanisms associated with HMs, and will increase our knowledge on their toxic effects on the body organs, leading to better management of metal poisoning. This review aims to enhance comprehension and offer sources for the judicious selection of microbial remediation technology for the detoxification of HMs. Microbial-based solutions that are sustainable could potentially offer crucial and cost-effective methods for reducing the toxicity of HMs.

Heterotrophic anodic denitrification coupled with cathodic metals recovery from on-site smelting wastewater with a bioelectrochemical system inoculated with mixed Castellaniella species

Although Castellaniella species are crucial for denitrification, there is no report on their capacity to carry out denitrification and anode respiration simultaneously in a bioelectrochemical system (BES). Herein, the ability of a mixed inoculum of electricigenic Castellaniella species to perform simultaneous denitrification and anode respiration coupled with cathodic metals recovery was investigated in a BES. Results showed that 500 mg/L NO₃^--N significantly decreased power generation, whereas 100 and 250 mg/L NO₃^--N had a lesser impact. The single-chamber MFCs (SCMFCs) fed with 100 and 250 mg/L NO₃^--N concentrations achieved a removal efficiency higher than 90% in all cycles. In contrast, the removal efficiency in the SCMFCs declined dramatically at 500 mg/L NO₃^--N, which might be attributable to decreased microbial viability as revealed by SEM and CLSM. EPS protein content and enzymatic activities of the biofilms decreased significantly at this concentration. Cyclic voltammetry results revealed that the 500 mg/L NO₃^--N concentration decreased the redox activities of anodic biofilms, while electrochemical impedance spectroscopy showed that the internal resistance of the SCMFCs at this concentration increased significantly. In addition, BES inoculated with the Castellaniella species was able to simultaneously perform heterotrophic anodic denitrification and cathodic metals recovery from real wastewater. The BES attained Cu²⁺, Hg²⁺, Pb²⁺, and Zn²⁺ removal efficiencies of 99.86 ± 0.10%, 99.98 ± 0.014%, 99.98 ± 0.01%, and 99.17 ± 0.30%, respectively, from the real wastewater. Cu²⁺ was bio-electrochemically reduced to Cu⁰ and Cu₂O, whereas Hg⁰ and HgO constituted the Hg species recovered via bioelectrochemical reduction and chemical deposition, respectively. Furthermore, Pb²⁺ and Zn²⁺ were bio-electrochemically reduced to Pb⁰ and Zn⁰, respectively. Over 89% of NO₃^--N was removed from the BES anolyte during the recovery of the metals. This research reveals promising denitrifying exoelectrogens for enhanced power generation, NO₃^--N removal, and heavy metals recovery in BES.

Bioelectrochemical systems-based metal removal and recovery from wastewater and polluted soil: Key factors, development, and perspective

Bioelectrochemical systems (BES) are considered efficient and sustainable technologies for bioenergy generation and simultaneously removal/recovery metal (loid)s from soil and wastewater. However, several current challenges of BES-based metal removal and recovery, especially concentrating target metals from complex contaminated wastewater or soil and their economic feasibility of engineering applications. This review summarized the applications of BES-based metal removal and recovery systems from wastewater and contaminated soil and evaluated their performances on electricity generation and metal removal/recovery efficiency. In addition, an in depth review of several key parameters (BES configurations, electrodes, catalysts, metal concentration, pH value, substrate categories, etc.) of BES-based metal removal and recovery was carried out to facilitate a deep understanding of their development and to suggest strategies for scaling up their specific application fields. Finally, the future intervention on multifunctional BES to improve their performances of mental removal and recovery were revealed.

Experimental study on the treatment of acid mine drainage containing heavy metals with domestic waste pyrolysis ash

Acid mine drainage (AMD) is a special kind of acidic wastewater produced in the process of mining and utilization. In this study, AMD was treated using the adsorption method. Domestic waste was prepared by pyrolysis, and the resulting waste pyrolysis ash adsorbent was studied experimentally by a static adsorption test to treat metal ions in AMD. The results showed that the maximum adsorption amounts of Zn²⁺, Cu²⁺, Mn²⁺, Fe²⁺, Pb²⁺, and Cd²⁺ reached 0.425, 0.593, 0.498, 18.519, 0.055, and 0.039 mg/g, respectively, when the amount of pyrolysis ash was added at 30 g/L, the initial pH of the water was 4.1 and the reaction time was 150 min. It was found that the waste pyrolysis ash could be reused at least three times by using Na₂S as the regeneration agent. The SEM and BET characterization results prove that its large specific surface areas and well-developed pore structures have the potential to promote the adsorption of metal ions. The pseudo-second-order kinetic equation and Freundlich adsorption isotherms fit the adsorption process well, and the experiments reveal that the metal ions in AMD are well treated by waste pyrolysis ash through adsorption, flocculation and chemical precipitation. Waste pyrolysis ash has great potential for the treatment of acid mine drainage, providing a new approach to solid waste disposal and new ideas for water treatment as a low-cost alternative material.

From Waste to Watts: Updates on Key Applications of Microbial Fuel Cells in Wastewater Treatment and Energy Production

Due to fossil fuel depletion and the rapid growth of industry, it is critical to develop environmentally friendly and long-term alternative energy technologies. Microbial fuel cells (MFCs) are a powerful platform for extracting energy from various sources and converting it to electricity. As no intermediate steps are required to harness the electricity from the organic substrate’s stored chemical energy, MFC technology offers a sustainable alternative source of energy production. The generation of electricity from the organic substances contained in waste using MFC technology could provide a cost-effective solution to the issue of environmental pollution and energy shortages in the near future. Thus, technical advancements in bioelectricity production from wastewater are becoming commercially viable. Due to practical limitations, and although promising prospects have been reported in recent investigations, MFCs are incapable of upscaling and of high-energy production. In this review paper, intensive research has been conducted on MFCs’ applications in the treatment of wastewater. Several types of waste have been extensively studied, including municipal or domestic waste, industrial waste, brewery wastewater, and urine waste. Furthermore, the applications of MFCs in the removal of nutrients (nitrogen and sulphates) and precious metals from wastewater were also intensively reviewed. As a result, the efficacy of various MFCs in achieving sustainable power generation from wastewater has been critically addressed in this study.

Current advances in microbial fuel cell technology toward removal of organic contaminants - A review

At present, water pollution and demand for clean energy are most pressing global issues. On a daily basis, huge quantity of organic wastes gets released into the water ecosystems, causing health related problems. The need-of-the-hour is to utilize proficient and cheaper techniques for complete removal of harmful organic contaminants from water. In this regard, microbial fuel cell (MFC) has emerged as a promising technique, which can produce useful electrical energy from organic wastes and decontaminate polluted water. Herein, we have systematically reviewed recently published results, observations and progress made on the applications of MFCs in degradation of organic contaminants, including organic synthetic dyes, agro pollutants, health care contaminants and other organics (such as phenols and their derivatives, polyhydrocarbons and caffeine). MFC-based hybrid technologies, including MFC-constructed wetland, MFC-photocatalysis, MFC-catalysis, MFC-Fenton process, etc., developed to obtain high removal efficiency and bioelectricity production simultaneously have been discussed. Further, this review assessed the influence of factors, such as nature of electrode catalysts, organic pollutants, electrolyte, microbes and operational conditions, on the performance of pristine and hybrid MFC reactors in terms of pollutant removal efficiency and power generation simultaneously. Moreover, the limitations and future research directions of MFCs for wastewater treatment have been discussed. Finally, a conclusive summary of the findings has been outlined.

Bioelectrochemical process for simultaneous removal of copper, ammonium and organic matter using an algae-assisted triple-chamber microbial fuel cell

Considering the adverse effect of heavy metals (such as Cu²⁺) on biological wastewater treatment processes, an algae-assisted triple-chamber microbial fuel cell (MFC) was established to remove Cu²⁺, COD and nitrogen sequentially, and also generate electricity. About 86.2% of the Cu²⁺ was removed in the first cathodic chamber, and the remaining Cu²⁺ was largely eliminated by algal uptake, contributing to an overall Cu²⁺ removal rate of 99.9% across the whole system. The nitrogen removal rate reached 79% in the system. The majority of the ammonium was assimilated by algae, and nitrogen oxides formed during the light period were denitrified at the cathode in the dark period. The variation in electrode potentials indicated that the cathode and anode potentials not only depended on the respective substrate concentrations, but also affected each other. The influence of algae on the microbial communities was greater than that of Cu²⁺ or the system structure. Devosia, Thauera, Pseudomonas, Acinetobacter and Flavobacterium may influence nitrogen removal, while Delftia, Thauera and Pseudomonas may play an important role in power generation. The present study has developed a practical method for removing pollutants from the wastewater containing heavy metals.