Preparation of GO/Fe3O4@PMDA/AuNPs nanocomposite for simultaneous determination of As3+ and Cu2+ by stripping voltammetry

Electrochemical sensing of Hg(ii) in chicken liver and snail shell extract samples using novel modified SDA/MWCNT electrodes

Heavy metal ions (Hg(ii)) were detected in fresh chicken liver and snail shell extract samples using novel synthesised SDA/MWCNT-modified electrodes. The synthesized N,N'-bis(salicylaldehyde)-1,2-diaminobenzene (SDA) ligand was characterized via FT-IR, 1H-NMR, and 13C-NMR spectroscopy. The hydroxyl and imine functional groups present in SDA act as active sites and bind to the MWCNT surface. The surface morphology of the modified SDA/MWCNT electrode exhibited a star-like crystal structure and the preconcentration of Hg(ii)-SDA/MWCNTs lead to a crystal cloud structure, as characterized by SEM with EDX. The enhancement of current and conductance of the SDA/MWCNT- and MWCNT-modified electrode was investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The conductance (σ) values for the MWCNT- and SDA/MWCNT-modified electrodes are 234.1 × 10-5 S cm-1 and 358.4 × 10-5 S cm-1, respectively, as determined by electrochemical impedance spectroscopy. Consequently, an electrochemical sensor with outstanding performance in terms of reproducibility, stability and anti-interference ability was fabricated. The stripping analysis of Hg(ii) was performed using square wave anodic stripping voltammetry (SWASV) and cyclic voltammetry (CV). Using SWASV, a linear range of Hg(ii) response was found to be 1.3 to 158 μg L-1, and the limit of detection (LOD) was 0.24 μg L-1. Finally, the results of the recovered value of Hg(ii) in freshly prepared chicken liver and snail shell extract samples by SWASV were compared with the atomic absorption spectroscopy (AAS) results.

Supported of gold nanoparticles on carboxymethyl lignin modified magnetic nanoparticles as an efficient catalyst for reduction of nitroarenes and treatment of human melanoma

This article represents the synthesis and characterizations of Au NPs immobilized and carboxymethyl lignin (CML) modified Fe3O4 nanoparticles (Fe3O4@CML/Au NPs) following a bio-inspired protocol without the participation of any toxic and harmful reductant or stabilizers. Following various physicochemical methodologies, such as FT-IR, FE-SEM, TEM, EDX, XRD, VSM, and ICP-OES, the textural characteristics and different structural aspects were evaluated. The Fe3O4@CML/Au NPs nanocomposite was subsequently explored towards the catalytic reduction of diverse aromatic nitro functions using green conditions. An excellent yield were achieved within very short reaction time. Nine recycling runs of the nanocatalyst were completed without a discernible loss of catalytic activity, thanks to its easy magnetic recovery. The DPPH assay was carried out to examine the antioxidant effectiveness. The Fe3O4@CML/Au NPs nanocomposite inhibited half of the DPPH in a 250 μg/mL solution. To measure the anti-human melanoma efficacy of Fe3O4@CML/Au NPs nanocomposite, MTT assay was applied on HT144, MUM2C, IPC-298 and SKMEL24 cell lines. Fe3O4@CML/Au NPs nanocomposite had high anti-human melanoma efficacy on above tumor cells. The best finding of anti-human melanoma properties of Fe3O4@CML/Au NPs nanocomposite was seen in the case of the SKMEL24 cell line. The IC50 of Fe3O4@CML/Au NPs nanocomposite was 137, 145, 185, and 125 μg/mL against HT144, MUM2C, IPC-298 and SKMEL24 cells, respectively. This research exhibited remarkable anti-human melanoma and antioxidant efficacies of Fe3O4@CML/Au NPs nanocomposite in the in vitro condition.

The comprehensive review about elements accumulation in industrial hemp (Cannabis sativa L.)

Cannabis sativa L., commonly known as industrial hemp, is a versatile plant with applications ranging from medicinal to agricultural and industrial uses. Despite its benefits, there is a notable gap in regulatory toxicology, in understanding the extent of element accumulation in hemp, which is critical due to its ability to absorb various elements from the soil, including heavy metals (Pb, Cd, Hg, and As), uptakes potential toxic elements (e.g., Sb, Sn, Sr, Bi, Tl), problematic elements (Ni, Cr, Co), and essential elements (Zn, Cu, Fe, Mn). The paper aims to enrich current understandings by offering a comprehensive analysis of elements absorption in industrial hemp. This study emphasizes the potential health risks linked with hemp consumption including regulatory toxicology aspects: limits, Permitted Daily Exposures (PDE), recommendations in different countries and from different agencies/bodies (like the WHO and the EU) based on route of administration, jurisdiction and actual literature review. This review contributes significantly to the knowledge base on hemp safety, serving as a valuable resource for researchers, regulatory bodies, and industry stakeholders.

Smartphone-based wearable microfluidic electrochemical sensor for on-site monitoring of copper ions in sweat without external driving

The directional movement of liquid without exogenous drive can show great potential in portable electrochemical platforms. Herein, we developed a portable electrochemical platform that drove electrolyte flow by surface tension gradient, which can realize collection of electrolyte, flow preconcentration and electrochemical detection of Cu2+. The induced graphene electrodes (LIG) was fabricated using laser direct writing, and flower cluster shaped ZnO nanorods (FC-ZnONRs) were prepared and modified on LIG, which provided a large amount of space for electrolyte to shuttled between the holes of LIG and ZnO, and increased the electrochemical active sites and electrons transport ability. The effect of surface tension gradients driving fluid flow could accelerate preconcentration, shorten detection time (save 300 s of preconcentration time) and enhance electrochemical responses in synergy with the 3D FC-ZnONRs/LIG. The microfluidic system possessed excellent performance for detection of Cu2+ ranged from 1 μg L-1 to 2100 μg L-1 with a low detection limit (LOD) of 0.0368 μg L-1 and high sensitivity of 0.414 μA (μg L-1)-1 cm-2. Additionally, this portable microfluidic system was successfully worn on the skin for analysing Cu2+ in human sweat, and the results showed good consistency with inductively coupled plasma-mass spectrometry (ICP-MS). This novel sensing system provides a sample collection, rapid detection, low cost and easy-to-operate strategy for heavy metal ions analysis in real samples and shows huge application prospects in point-of-care testing.

Targeting anticancer immunity in oral cancer: Drugs, products, and nanoparticles

Oral cavity carcinomas are the most frequent malignancies among head and neck malignancies. Oral tumors include not only oral cancer cells with different potency and stemness but also consist of diverse cells, containing anticancer immune cells, stromal and also immunosuppressive cells that influence the immune system reactions. The infiltrated T and natural killer (NK) cells are the substantial tumor-suppressive immune compartments in the tumor. The infiltration of these cells has substantial impacts on the response of tumors to immunotherapy, chemotherapy, and radiotherapy. Nevertheless, cancer cells, stromal cells, and some other compartments like regulatory T cells (Tregs), macrophages, and myeloid-derived suppressor cells (MDSCs) can repress the immune responses against malignant cells. Boosting anticancer immunity by inducing the immune system or repressing the tumor-promoting cells is one of the intriguing approaches for the eradication of malignant cells such as oral cancers. This review aims to concentrate on the secretions and interactions in the oral tumor immune microenvironment. We review targeting tumor stroma, immune system and immunosuppressive interactions in oral tumors. This review will also focus on therapeutic targets and therapeutic agents such as nanoparticles and products with anti-tumor potency that can boost anticancer immunity in oral tumors. We also explain possible future perspectives including delivery of various cells, natural products and drugs by nanoparticles for boosting anticancer immunity in oral tumors.

Nanoparticles and nanofiltration for wastewater treatment: From polluted to fresh water

Water pollution poses significant threats to both ecosystems and human health. Mitigating this issue requires effective treatment of domestic wastewater to convert waste into bio-fertilizers and gas. Neglecting liquid waste treatment carries severe consequences for health and the environment. This review focuses on intelligent technologies for water and wastewater treatment, targeting waterborne diseases. It covers pollution prevention and purification methods, including hydrotherapy, membrane filtration, mechanical filters, reverse osmosis, ion exchange, and copper-zinc cleaning. The article also highlights domestic purification, field techniques, heavy metal removal, and emerging technologies like nanochips, graphene, nanofiltration, atmospheric water generation, and wastewater treatment plants (WWTPs)-based cleaning. Emphasizing water cleaning's significance for ecosystem protection and human health, the review discusses pollution challenges and explores the integration of wastewater treatment, coagulant processes, and nanoparticle utilization in management. It advocates collaborative efforts and innovative research for freshwater preservation and pollution mitigation. Innovative biological systems, combined with filtration, disinfection, and membranes, can elevate recovery rates by up to 90%, surpassing individual primary (<10%) or biological methods (≤50%). Advanced treatment methods can achieve up to 95% water recovery, exceeding UN goals for clean water and sanitation (Goal 6). This progress aligns with climate action objectives and safeguards vital water-rich habitats (Goal 13). The future holds promise with advanced purification techniques enhancing water quality and availability, underscoring the need for responsible water conservation and management for a sustainable future.

Evaluation of thallium ion as an effective ion in human health using an electrochemical sensor

Exposure to thallium (Tl), a noxious heavy metal, poses significant health risks to both humans and animals upon ingestion. Therefore, monitoring Tl levels in the environment is crucial to prevent human exposure and reduce the risk of developing severe health problems. This paper presents the development of a highly sensitive Tl ions sensor through surface modification of a glassy carbon electrode with a nanocomposite comprising MnO2 magnetic sepiolite and multi-walled carbon nanotubes (MnO2@Fe3O4/Sep/MWCNT/GCE). Multiple methodologies were employed to assess the performance of the newly developed sensor. By employing square wave anodic stripping voltammetry (SWASV) to optimize the measurement conditions, notable enhancements were observed in the stripping peak currents of Tl (I) on the MnO2@Fe3O4/Sep/MWCNT/GCE surface. The effectiveness of the nanocomposite in facilitating electron transfer between the Tl (I) ions (guest) and the electrode (host) was demonstrated from the enhanced signals observed at the different modified electrode surfaces under optimal conditions. The developed sensor displayed a wide linear range of 0.1-1500 ppb for Tl (I) and a low detection limit of 0.03 ppb for Tl (I). It was found to be selective for Tl (I) ions while remaining unaffected by interfering non-target ions in the presence of the target ions. Despite its simple preparation procedure, the modified electrode exhibited high stability and excellent reproducibility for measuring Tl (I). The outstanding electroanalytical performances of the MnO2@Fe3O4/Sep/MWCNT/GCE electrode enabled its successful use as an ultrasensitive sensor for determining trace amounts of Tl in environmental samples.

Development of an impedimetric sensor for susceptible detection of melatonin at picomolar concentrations in diverse pharmaceutical and human specimens

Our investigation aimed to create and manufacture an electrochemical impedance sensor with the purpose of improving the detection efficiency of melatonin (ME). To achieve this objective, we employed gold nanoparticles coated on polydopamine formed in glassy carbon electrodes (AuNPs/PDA/GCE) as a means to enhance the sensor's capabilities. A novel approach employing the signal-off strategy and electrochemical impedance spectroscopy (EIS) technique was utilized to determine ME. When the AuNPs/PDA/GCE electrode was immersed in a buffered solution containing ME, and the oxidation current of AuNPs was recorded, it was observed that the oxidation current of AuNPs decreased upon the introduction of ME molecules. The decrease in electrical current can be ascribed to the inhibitory impact of ME molecule adsorption on the electrode surface with applying -0.2 V for 150 s in acetate buffer solution (ABS) (pH, 5) through various mechanisms, which hinders the electron transfer process crucial for AuNPs oxidation. Consequently, by utilizing EIS, various concentrations of ME were quantified spanning from 1 to 18 pM. Moreover, the ME sensor achieved an impressive detection limit of 0.32 pM, indicating its remarkable sensitivity in detecting low concentrations of ME. Importantly, these novel sensors demonstrated exceptional attributes in terms of sensitivity, specificity, stability, and repeatability. The outstanding performance of these sensors, coupled with their desirable attributes, establishes their considerable potential for a wide range of practical applications. These applications encompass various fields such as clinical diagnostics, pharmaceutical analysis, environmental monitoring, and industrial quality control, where accurate and sensitive detection of ME is of utmost importance.

Drug permeation enhancement, efficacy, and safety assessment of azelaic acid loaded SNEDDS hydrogel to overcome the treatment barriers of atopic dermatitis

Atopic dermatitis is one of the most widespread chronic inflammatory skin conditions that can occur at any age, though the prevalence is highest in children. The purpose of the current study was to prepare and optimize the azelaic acid (AzA) loaded SNEDDS using Pseudo ternary phase diagram, which was subsequently incorporated into the Carbopol 940 hydrogel for the treatment of atopic dermatitis. The composition was evaluated for size, entrapment efficiency, in vitro, ex vivo, and in vivo studies. The polydispersity index of the optimized preparation was found to be less than 0.5, and the size of the distributed globules was found to be 151.20 ± 3.67 nm. The SNEDDS hydrogel was characterized for pH, viscosity, spreadability, and texture analysis. When compared to the marketed formulation, SNEDDS hydrogel was found to have a higher rate of permeation through the rat skin. In addition, a skin irritation test carried out on experimental animals showed that the SNEDDS formulation did not exhibit any erythematous symptoms after a 24-h exposure. In conclusion, the topical delivery of AzA through the skin using SNEDDS hydrogel could prove to be an effective approach for the treatment of atopic dermatitis.

Fabrication of silver nanoparticles immobilized on magnetic lignosulfonate: Evaluation of its catalytic activity in the N-acetylation reactions and investigation of its anti-cutaneous squamous cell carcinoma effects

Due to the non-optimal response of most types of cancer to various treatment methods and their rapid progress, research continues in the field of producing drugs with less toxicity and greater efficiency. There are many nanocomposites with diverse biological activities that include part of anticancer drugs in new pharmacological science. The present investigation describes a green procedure for the in situ support of Ag nanoparticles (NPs) over sodium lignosulfonate (NaLS) modified magnetic nanoparticles (Fe3O4@NaLS/Ag) and its subsequent biological and chemical performance. FT-IR, TEM, FE-SEM, EDS, ICP, VSM and XRD techniques were used to characterize the synthesized Fe3O4@NaLS/Ag. The catalytic efficacy of the desired composite was applied in the N-acetylation of various amines in the presence of Ac2O under solvent-free conditions. The Fe3O4@NaLS/Ag catalyst was recovered by an external magnet and reused for nine runs without a significant decrease in the activity. The cytotoxic and anti-cutaneous squamous cell carcinoma potentials of biologically synthesized Fe3O4@NaLS/Ag nanocomposite against PM1 and MET1 cells were determined. The anti-cutaneous squamous cell carcinoma properties of the Fe3O4@NaLS/Ag nanocomposite could significantly remove PM1 and MET1 cells. The IC50 of Fe3O4@NaLS/Ag nanocomposite was 288 and 270 μg/mL against PM1 and MET1 cells, respectively. Also, Fe3O4@NaLS/Ag nanocomposite presented a high antioxidant potential according to the IC50 value. According to the above results, the recent nanocomposite can be used in treating cutaneous squamous cell carcinoma after doing clinical trial studies.

Adsorption of ibuprofen using waste coffee derived carbon architecture: Experimental, kinetic modeling, statistical and bio-inspired optimization

Pharmaceuticals in water are a growing environmental concern, as they can harm aquatic life and human health. To address this issue, an adsorbent made from coffee waste that effectively removes ibuprofen (a common pharmaceutical pollutant) from wastewater was developed. The experimental adsorption phase was planned using a Design of Experiments approach with Box-Behnken strategy. The relation between the ibuprofen removal efficiency and various independent variables, including adsorbent weight (0.01-0.1 g) and pH (3-9), was evaluated via a regression model with 3-level and 4-factors using the Response surface methodology (RSM) . The optimal ibuprofen removal was achieved after 15 min using 0.1 g adsorbent at 32.4 °C and pH = 6.9. Moreover, the process was optimized using two powerful bio-inspired metaheuristics (Bacterial Foraging Optimization and Virus Optimization Algorithm). The adsorption kinetics, equilibrium, and thermodynamics of ibuprofen onto waste coffee-derived activated carbon were modeled at the identified optimal conditions. The Langmuir and Freundlich adsorption isotherms were implemented to investigate adsorption equilibrium, and thermodynamic parameters were also calculated. According to the Langmuir isotherm model, the adsorbent's maximum adsorption capacity was 350.00 mg g-1 at 35 °C. The findings revealed that the ibuprofen adsorption was well-matched with the Freundlich isotherm model, indicating multilayer adsorption on heterogeneous sites. The computed positive enthalpy value showed the endothermic nature of ibuprofen adsorption at the adsorbate interface.

Application of Co3O4 nanocrystal/rGO for simultaneous electrochemical detection of cadmium and lead in environmental waters

Sensing of cadmium (Cd) and lead (Pb) in environmental samples is crucial for identifying potential health risks associated with exposure to these heavy metals as well as understanding the extent of heavy metal contamination in different environments and its impact on the ecosystem. The present study elucidates the development of a novel electrochemical sensor that can detect Cd (II) and Pb (II) ions simultaneously. This sensor is fabricated using reduced graphene oxide (rGO) and cobalt oxide nanocrystals (Co₃O₄ nanocrystals/rGO). The characterization of Co₃O₄ nanocrystals/rGO was done by using various analytical techniques. The incorporation of cobalt oxide nanocrystals with intense absorption properties results in an amplification of the electrochemical current generated on the surface of the sensor by heavy metals. This, when coupled with the unique properties of the GO layer, enables the identification of trace levels of Cd (II) and Pb (II) in the surrounding environment. The electrochemical testing parameters were meticulously optimized to obtain high sensitivity and selectivity. The Co₃O₄ nanocrystals/rGO sensor exhibited exceptional performance in detecting Cd (II) and Pb (II) within a concentration range of 0.1-450 ppb. Notably, the limits of detection (LOD) for Pb (II) and Cd (II) were found to be highly impressive at 0.034 ppb and 0.062 ppb, respectively. The Co₃O₄ nanocrystals/rGO sensor integrated with the SWASV method displayed notable resistance to interference and exhibited consistent reproducibility and stability. Therefore, the suggested sensor has the potential to serve as a technique for detecting both ions in aqueous samples using SWASV analysis.

Optimization and analytical behavior of a morphine electrochemical sensor in environmental and biological samples based on graphite rod electrode using graphene/Co3O4 nanocomposite

In this research, a new sensor based on graphene/Co₃O₄ (Gr/Co₃O₄) nanocomposite was employed for electrochemically determination of morphine (MOR). The modifier was synthesized with a simple hydrothermal technique and well characterized using X-ray difraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectroscopy (EDS) tools. The modified graphite rod electrode (GRE) was revealed a high electrochemical catalytic activity for the MOR oxidation and employed for the electroanalysis of trace MOR concentration by means of differential pulse voltammetry (DPV) technique. At the optimum experimental factors, the resulting sensor offered a good response for MOR in the concentration range of 0.5-100.0 μM with a detection limit of 80 nM. In addition, the modified electrode demonstrated an acceptable selectivity, stability and reproducibility. This assay was also provided a valid platform for the detection of MOR in environmental and biological samples with acceptable recoveries and RSD in the range of 97.2-102.8% and 1.7-3.4%, respectively. Taking to the simplicity, low cost and short analysis time, this approach is suggested for clinical, environmental and forensic testing of MOR.

Insight into the adsorptive removal of ibuprofen using porous carbonaceous materials: A review

Over the last decade, the removal of pharmaceuticals from aquatic bodies has garnered substantial attention from the scientific community. Ibuprofen (IBP), a non-steroidal anti-inflammatory drug, is released into the environment in pharmaceutical waste as well as medical, hospital, and household effluents. Adsorption technology is a highly efficient approach to reduce the IBP in the aquatic environment, particularly at low IBP concentrations. Due to the exceptional surface properties of carbonaceous materials, they are considered ideal adsorbents for the IBP removal of, with high binding capacity. Given the importance of the topic, the adsorptive removal of IBP from effluent using various carbonaceous adsorbents, including activated carbon, biochar, graphene-based materials, and carbon nanostructures, has been compiled and critically reviewed. Furthermore, the adsorption behavior, binding mechanisms, the most effective parameters, thermodynamics, and regeneration methods as well as the cost analysis were comprehensively reviewed for modified and unmodified carbonaceous adsorbents. The compiled studies on the IBP adsorption shows that the IBP uptake of some carbon-based adsorbents is significantly than that of commercial activated carbons. In the future, much attention is needed for practical utilization and upscaling of the research findings to aid the management and sustainability of water resource.

MOFs-based Fe@YAU-101/GCE electrochemical sensor platform for highly selective detecting trace multiplex heavy metal ions

The construction of sensors with specific recognition functions can easily, sensitively and efficiently detect heavy metal ions, which is a demand in the field of electrochemical sensing and an important topic in the detection of environmental pollutants. An electrochemical sensor based on MOFs composites was developed for sensing of multiplex metal ions. The large surface area, adjustable porosities and channels in MOFs facilitate successful loading of sufficient quantities highly active units. The active units and pore structures of MOFs are regulated and synergetic with each other to enhance the electrochemical activity of MOFs composites. Thus, the selectivity, sensitivity and reproducibility of MOFs composites have been improved. Fortunately, after characterization, Fe@YAU-101/GCE sensor with strong signal was successfully constructed. In the presence of target metal ions in solution, the Fe@YAU-101/GCE can efficiently and synchronously identify Hg²⁺, Pb²⁺, and Cd²⁺. The detection limits (LOD) are 6.67 × 10^-10 M(Cd²⁺), 3.33 × 10^-10 M(Pb²⁺) and 1.33 × 10^-8 M (Hg²⁺), and are superior to the permissible limits set by the National Environmental Protection Agency. The electrochemical sensor is simple without sophisticated instrumentation and testing processes, hence promising for practical applications.

One-step electrochemical elaboration of SnO2 modified electrode for lead ion trace detection in drinking water using SWASV

A facile method was proposed for the elaboration of an electrochemical sensor for heavy metal's trace detection by using square wave anodic stripping voltammetry (SWASV); this method is based on a simple anodic conversion of tin electrode into Sn/SnO₂ modified electrode. Both electrochemical and physico-chemical techniques were used to confirm the modification process and better understand the electrode's behavior. Then, depending on the operating conditions, the response signal was studied and adjusted in order to obtain optimal sensor performance. When optimized, the proposed method reached a lowest detection limit (LOD) of 2.15 μg L^-1 (0.0104 μM), and quantification limit (LOQ) of 5.36 μg L^-1 (0.0259 μM), in linearity range between from 6.2 and 20.7 μg L^-1. Additionally, after having used the elaborated electrode for ten successive measurements, the repeatability remains very high with an RSD of approximately 5.3%; furthermore, ten other species appear to have very slight effect on Pb(II) detection. Finally, for the method validation, the proposed electrode was able to sense different lead concentration integrated in a local bottled spring water by showing recovery levels ranging from 103.8 to 108.4%.

A nanoporous gold film sensor modified with polypyrrole/CuO nanocomposite for electrochemical determination of piroxicam and tramadole

In this paper, an electrochemical sensor was developed to determine piroxicam (PX) and tramadole (Tr) based on their enhanced electrochemical responses at the surface of the polypyrrole/CuO nanocomposite-modified nanoporous gold film (NPGF) electrode. The experimental results showed that PX provide an oxidation peak at 0.65 V in pH = 8.0. The DPV results were linearly affiliated on PX concentration within the two closed windows (C1_PX = 0.05-30.0 μM, correlation coefficient of 0.9905, and C2_PX = 50.0-300.0 μM, correlation coefficient of 0.9927). From voltammetric curves, the detection limit (LOD = 3S_b/m) for PX at a surface of PPY-CuO-NPGF electrode was appeared to be 0.01 μM. Furthermore, the ability of PPY-CuO-NPGF electrode for simultaneous measurement of PX and Tr was investigated. The suggested sensor shows a long-time stability, good repeatability, and rapid response in the mixture media of PX and Tr.

A signal-on electrochemical DNA biosensor based on exonuclease III-assisted recycling amplification

DNA electrochemical detection technology has attracted tremendous interest in recent years. However, a facile and sensitive method for the detection of the disease indicators or genes is still waiting. Herein, we constructed a signal-on electrochemical platform for detecting the manganese superoxide dismutase (MnSOD) gene by incorporating a redox electrochemical signal probe (methylene blue) and exonuclease III-assisted target recycling signal amplification strategy. The sensor was prepared by self-assembly of a capture DNA probe of thiol-modified on GCE with gold electrodeposition. In the presence of target DNA, the exonuclease III can cleave the duplexes formed by the target DNA and the redox-labeled hairpin probes, release the target DNA and produce a residual sequence. The target DNA can continue to hybridize with the hairpin probe for the next cycle of amplification. The residual sequence hybridized with the surface-immobilized capture probes on AuNPs-modified GCE to generate a significantly amplified redox current. In particular, the redox current value of the resultant sensor showed a linear relationship with MnSOD gene concentration in the range of 1-10⁴ pM with the detection limit as low as 0.3 pM. Furthermore, the sensor has excellent specificity and can distinguish single-base mismatch from perfectly matched target DNA. The sensor is fast in operation, and simple in design for detecting different DNA sequences or DNA identification by selecting the appropriate probe sequence, thus shedding light on a good promising application when encountering disease outbreaks or for the early clinical diagnosis of gene-related diseases.

Chemically modified covalent organic frameworks for a healthy and sustainable environment: First-principles study

Pure water is a key element for a sustainable and healthy environment of human inhabitation. Since major sources of water contamination are industrially generated heavy metal cations there is great demand for efficient methods of their treatment. Here, using density functional theory, we investigate the covalent organic framework's electronic and optical properties and their interaction with the most dangerous heavy metal pollutants, namely Hg⁺², Pb^+2, and Cd⁺². We consider biphenyl boroxine covalent organic frameworks before and after chemical modification with CN, COOH, NH₂, and NO₂ groups. In addition to the molecular geometries, such parameters as the dipole moment, chemical potential, electronegativity, chemical hardness, and binding energy are calculated. It is found that CN, COOH, and NO₂ functional groups are favorable for intermolecular bonding with harmful transition metals. The functionalization with the mentioned groups reduces the band gap of the pristine covalent organic frameworks and increases their reactivity. As a result, strong complexes with Cd⁺², Hg⁺², and Pb⁺² can form, which, as follows from our calculations, can be detected by the red shift in their optical absorption spectra.

Ultrafast construction of 3D ultrathin NiCo-LDH@Cu heteronanosheet array by plasma magnetron sputtering for non-enzymatic glucose sensing in beverage and human serum

In this work, a 3D ultra-thin NiCo-LDH nanosheet array coated Cu nanoparticles on carbon cloth (NiCo-LDH@Cu NSA/CC) was ultrafast synthesized by plasma magnetron sputtering for the first time. This method has low toxicity and is easy to operate. As a durable and efficient 3D heteronanoarray electrocatalyst for glucose detection, NiCo-LDH@Cu NSA/CC has higher stable conductivity and faster electron transport rate than NiCo-LDH NSA/CC and Cu nanoparticles, which work through synergistic effect to form a high-performance sensing platform. The NiCo-LDH@Cu NSA/CC heteronanosheet structure has good electrocatalytic performance for glucose oxidation, with the sensitivity of the two linear ranges (0.001-1 mmol L^-1 and 1-6 mmol L^-1) being 9710 μA L mmol^-1 cm^-2 and 4870 μA L mmol^-1 cm^-2, respectively, and the detection limit (LOD) is 157 nmol L^-1 (S/N = 3). The sensor has been successfully applied to detect glucose in beverages and serum.

Simple high-temperature annealing affords commercial carbon cloth with enhanced electrochemical performance for highly sensitive detection of imidacloprid

Imidacloprid (IDP) residue in modern agricultural production seriously endangers human health and environmental safety. The establishment of a rapid and efficient method for the detection of IDP residue can effectively prevent its harm to human health. Herein, we demonstrate the carbon cloth (CC) prepared by a high-temperature annealing strategy possesses enhanced electrochemical performance, which could be directly used in electrochemical IDP sensing. Annealed carbon cloth (ACC) is endowed with higher defects, rougher surfaces, more functional groups, more hydrophilic surface, and increased ion-accessible surface area. Furthermore, the ACC electrode shows superior electrocatalytic reduction activity towards IDP, possessing a wide linear range of 5-100 μM, a low detection limit of 0.04 μM, and high sensitivity of 35.58 μA mM^-1 cm^-2. Meanwhile, this sensor can be applied for sensing IDP in grapes and apples with a good recovery of 96.8-104.1%. Compared with other modified electrodes, the ACC electrode has the advantages of no binder, no complicated modification, excellent detection effect, low cost, and easy large-scale production. Consequently, this work designs a self-supporting metal-free electrode with high electrochemical performance, providing a new idea for the development of environmentally friendly IDP sensors.

Interference-resistant aptasensor with tetrahedral DNA nanostructure for profenofos detection based on the composites of graphene oxide and polyaniline

In this work, an interference-resistant electrochemical aptasensor that could detect profenofos in vegetables was constructed based on complexes of graphene oxide and polyaniline (GO@PANI) and gold nanoparticles-tetrahedral DNA nanostructure (Au-TDN). Compared with a single chain aptamer, the tetrahedral DNA nanostructure is highly stable and allows the aptamer on this structure to stand in a highly ordered position on an electrode surface. Moreover, the AuNPs are biocompatible and can protect the activity of the aptamer, which can improve the assembly success rate of Au-TDN. Besides, the conductivity of PANI had been tremendously enhanced thanks to the existence of GO, which improved the dispersion of PANI. The GO@PANI was prepared by a chemical synthesis method, which had a large surface area and was able to adsorb many Au-TDN. Under optimal working parameters, the constructed aptasensor exhibited good electrochemical sensing performance with a detection limit of 10.50 pg/mL and a linear range of 1.0 × 10²-1.0 × 10⁷ pg/mL. In addition, it was employed in detecting profenofos in vegetables with a good recovery rate of 90.41-116.37 %. More importantly, the aptasensor also has excellent stability and high selectivity. This study provides a promising method to avoid interference in the detection of profenofos by sensors.

Graphene-Based Electrochemical Sensors for Psychoactive Drugs

Sensors developed from nanomaterials are increasingly used in a variety of fields, from simple wearable or medical sensors to be used at home to monitor health, to more complicated sensors being used by border customs or aviation industries. In recent times, nanoparticle-based sensors have begun to revolutionize drug-detection techniques, mainly due to their affordability, ease of use and portability, compared to conventional chromatography techniques. Thin graphene layers provide a significantly high surface to weight ratio compared to other nanomaterials, a characteristic that has led to the design of more sensitive and reliable sensors. The exceptional properties of graphene coupled with its potential to be tuned to target specific molecules have made graphene-based sensors one of the most popular and well-researched sensing materials of the past two decades with applications in environmental monitoring, medical diagnostics, and industries. Here, we present a review of developments in the applications of graphene-based sensors in sensing drugs such as cocaine, morphine, methamphetamine, ketamine, tramadol and so forth in the past decade. We compare graphene sensors with other sensors developed from ultrathin two-dimensional materials, such as transition-metal dichalcogenides, hexagonal boron nitrate, and MXenes, to measure drugs directly and indirectly, in various samples.

Fast screening method for early diagnostic of gastric cancer based on utilization of a chitosan - S-doped graphene - based needle stochastic sensors

Needle stochastic sensors were developed for the assay of carbohydrate antigen 19-9 (CA 19-9) and carcinoembryonic antigen (CEA) in different biological samples (e.g., whole blood, tissues, urine, and saliva). Sulfur doped graphene powders were modified with chitosan; paraffin oil was added to form a homogeneous paste that was used as active side of the stochastic sensors. High sensitivities and low limits of determination were achieved for the assay of CA19-9 and CEA in biological samples. The validation of the proposed screening method (which is utilizing the stochastic sensors as screening tools) was made by using real biological samples obtained from confirmed patients with gastric cancer; very good correlations for the concentrations of CEA and CA19-9 were obtained using the needle stochastic sensors.

Dual-response electrochemical electrode for sensitive monitoring of topotecan and mitomycin as anticancer drugs in real samples

This research paper employed an innovative electrochemical electrode to simultaneously determine topotecan (TPT) and mitomycin (MMC) as anticancer agents. For this purpose, a novel nanocomposite was synthesized using a hydrothermal procedure. The nanocomposites were characterized using FTIR, STEM, FESEM, mapping analysis, EDX, and XRD methods. The novelty of this work is the successful synthesis of Fe₃O₄ decorated on the surface of CuCo₂S₄ (Fe₃O₄@CuCo₂S₄) nanocomposites showed two separate anodic peaks at 0.8 V for TPT and 1.0 V for MMC with potential separation of 0.2 V. This was enough for the simultaneous electrochemical determination of topotecan and mitomycin on a glassy carbon electrode (GCE), simultaneously. At optimized conditions, the developed electrode exhibited linear responses with TPT and MMC concentration in the ranges of 0.01-0.89 and 0.89-8.95 μM for topotecan and 0.1-19.53 μM for mitomycin. The detection limits were observed as 6.94 nM and 80.00 nM for topotecan and mitomycin, respectively. The fabricated Fe₃O₄@CuCo₂S₄/GCE showed high sensitivity, long-term stability, and repeatability towards the sensing of TPT and MMC simultaneously and can be utilized in real samples. The obtained results confirmed that the fabricated Fe₃O₄@CuCo₂S₄/GCE nanocomposites can be utilize in the simultaneous electrochemical determination of topotecan and mitomycin in real samples.

Advances in Electrochemical Detection Electrodes for As(III)

Arsenic is extremely abundant in the Earth’s crust and is one of the most common environmental pollutants in nature. In the natural water environment and surface soil, arsenic exists mainly in the form of trivalent arsenite (As(III)) and pentavalent arsenate (As(V)) ions, and its toxicity can be a serious threat to human health. In order to manage the increasingly serious arsenic pollution in the living environment and maintain a healthy and beautiful ecosystem for human beings, it is urgent to conduct research on an efficient sensing method suitable for the detection of As(III) ions. Electrochemical sensing has the advantages of simple instrumentation, high sensitivity, good selectivity, portability, and the ability to be analyzed on site. This paper reviews various electrode systems developed in recent years based on nanomaterials such as noble metals, bimetals, other metals and their compounds, carbon nano, and biomolecules, with a focus on electrodes modified with noble metal and metal compound nanomaterials, and evaluates their performance for the detection of arsenic. They have great potential for achieving the rapid detection of arsenic due to their excellent sensitivity and strong interference immunity. In addition, this paper discusses the relatively rare application of silicon and its compounds as well as novel polymers in achieving arsenic detection, which provides new ideas for investigating novel nanomaterial sensing. We hope that this review will further advance the research progress of high-performance arsenic sensors based on novel nanomaterials.

Label-free detection of Cu(II) in fish using a graphene field-effect transistor gated by structure-switching aptamer probes

Copper sulfate is a widely used agent to control insects, bacteria and algae for fishery. However, excess amount of copper ions in water accumulate in aquatic products through the ecological cycle system, highly threatening food safety and public health. Therefore, it is urgent to develop a rapid and efficient method for the determination of copper content in aquatic products. In this study, we developed a label-free biosensor for Cu(II) based on a graphene field-effect transistor gated by structure-switching aptamer probes (SSA-GFET) against Cu(II) we obtained before. The detection mechanism of the biosensor is attributed to the surface charge shift and the potential change of the gate electrode upon the specific binding of Cu(II). The SSA-GFET biosensor has a low detection limit of 10 nM and a linear range of 10 nM to 3 μM to Cu(II). In addition to the excellent selectivity to Cu(II), the biosensor also showes the advantage of high recovery rate for detection of Cu(II) in real fish samples. Because of the detection characteristics of label-free SSA-GFET, it has great advantages in the field of food safety and environmental detection.

Functionalized Fe3O4 Nanoparticles as Glassy Carbon Electrode Modifiers for Heavy Metal Ions Detection-A Mini Review

Over the past few decades, nanoparticles of iron oxide Fe3O4 (magnetite) gained significant attention in both basic studies and many practical applications. Their unique properties such as superparamagnetism, low toxicity, synthesis simplicity, high surface area to volume ratio, simple separation methodology by an external magnetic field, and renewability are the reasons for their successful utilisation in environmental remediation, biomedical, and agricultural applications. Moreover, the magnetite surface modification enables the successful binding of various analytes. In this work, we discuss the usage of core-shell nanoparticles and nanocomposites based on Fe3O4 for the modification of the GC electrode surface. Furthermore, this review focuses on the heavy metal ions electrochemical detection using Fe3O4-based nanoparticles-modified electrodes. Moreover, the most frequently used electrochemical methods, such as differential pulse anodic stripping voltammetry and measurement conditions, including deposition potential, deposition time, and electrolyte selection, are discussed.

Copper Film Modified Glassy Carbon Electrode and Copper Film with Carbon Nanotubes Modified Screen-Printed Electrode for the Cd(II) Determination

A copper film modified glassy carbon electrode (CuF/GCE) and a novel copper film with carbon nanotubes modified screen-printed electrode (CuF/CN/SPE) for anodic stripping voltammetric measurement of ultratrace levels of Cd(II) are presented. During the development of the research procedure, several main parameters were investigated and optimized. The optimal electroanalytical performance of the working electrodes was achieved in electrolyte 0.1 M HCl and 2 × 10⁻⁴ M Cu(II). The copper film modified glassy carbon electrode exhibited operation in the presence of dissolved oxygen with a calculated limit of detection of 1.7 × 10⁻¹⁰ M and 210 s accumulation time, repeatability with RSD of 4.2% (n = 5). In the case of copper film with carbon nanotubes modified screen-printed electrode limit of detection amounted 1.3 × 10⁻¹⁰ M for accumulation time of 210 s and with RSD of 4.5% (n = 5). The calibration curve has a linear range in the tested concentration of 5 × 10⁻¹⁰–5 × 10⁻⁷ M (r = 0.999) for CuF/GCE and 3 × 10⁻¹⁰–3 × 10⁻⁷ M (r = 0.999) for CuF/CN/SPE with 210 s accumulation time in both cases. The used electrodes enable trace determination of cadmium in different environmental water samples containing organic matrix. The validation of the proposed procedures was carried out through analysis certified reference materials: TM-25.5, SPS-SW1, and SPS-WW1.

A Methylene Blue Assisted Electrochemical Sensor for Determination of Drug Resistance of Escherichia coli

Due to the abuse of antibiotics in clinical, animal husbandry, and aquaculture, drug-resistant pathogens are produced, which poses a great threat to human and the public health. At present, a rapid and effective drug sensitivity test method is urgently needed to effectively control the spread of drug-resistant bacteria. Using methylene blue as a redox probe, the electrochemical signals of methylene blue in drug-resistant Escherichia coli strains were analyzed by a CV method. Graphene ink has been used for enhancing the electrochemical signal. Compared with the results of the traditional drug sensitivity test, we proposed a rapid electrochemical drug sensitivity test method which can effectively identify the drug sensitivity of Escherichia coli. The sensitivity of four E. coli isolates to ciprofloxacin, gentamicin, and ampicillin was tested by an electrochemical drug sensitivity test. The respiratory activity value %RA was used as an indicator of bacterial resistance by electrochemical method.