Chemical calibration, performance, validation and applications of the polar organic chemical integrative sampler (POCIS) in aquatic environments

Occurrence and environmental risk assessment of pesticides reveal important threats to aquatic organisms in precordilleran rivers of north-central Chile

While pesticides are essential for food production, their widespread use poses environmental risks beyond lowland areas. Recent evidence indicates that mountain ecosystems are also vulnerable due to both local agriculture and long-range atmospheric transport. This study assesses pesticide contamination and ecological risks in five mountainous agricultural watersheds of north-central Chile, where pesticides support intensive crop production. Using primarily polar organic chemical integrative samplers (POCIS), complemented by sediment samples, we found pesticides at 26 of 30 sampled sites. Detection varied by location and method. Desethylatrazine, an atrazine metabolite, was most frequently found in POCIS samples, detected at 20 sites across all watersheds. While other pesticides only occurred at few sites, their presence across multiple, geographically dispersed locations contributed to extensive ecological risk. Northern watersheds (Limarí, Choapa, Aconcagua) showed the highest ecological risks, despite lower pesticide loads, due to the presence of highly toxic insecticides. Key factors influencing pesticide distribution included water conductivity, agricultural land use, and latitude. Ecotoxicological risk assessments revealed eight pesticides exceeding high-risk thresholds for aquatic organisms-mainly insecticides and fungicides. Pyrethroids such as deltamethrin, cyfluthrin, and lambda-cyhalothrin posed severe threats to fish and invertebrates. High-risk levels were also detected in sediments, particularly in the northernmost Limarí watershed. These findings underscore the urgent need for targeted monitoring and stricter pesticide regulation in mountain freshwater ecosystems of Chile, which are vital water sources and harbor unique biodiversity. This study provides one of the first comprehensive evaluations of pesticide risks in mountainous rivers, highlighting the ecological threats from agricultural contaminants.

Passive sampling of contaminants of emerging concern in a Caribbean urban estuary of Puerto Rico

Contaminants of emerging concern (CECs) have not been extensively studied in Caribbean estuaries, particularly in Puerto Rico. Polar organic chemical integrative samplers were deployed in surface waters at five sampling sites in the San Juan Bay Estuary to investigate the occurrence and distribution of 137 CECs, resulting in the detection of 64 chemicals (51 pharmaceuticals and personal care products "PPCPs", 12 hormones plus sucralose) at least in one sampling site, and with 35 chemicals obtaining a 100 % detection frequency. Wastewater intrusion was implicated in the presence of CECs based on the detection of sucralose and other wastewater tracers. Condado Lagoon was the most polluted site impacted by untreated wastewater, showing the highest levels of 30 of the 64 detected CECs, and the largest proportion of detected CECs, particularly PPCPs. Levels of estrone and 17β-estradiol represent a high potential risk for adverse effects on aquatic organisms in this Caribbean urban estuary.

Role of membrane porosity in passive sampling of aquatic contaminants for stable isotope analysis: enhancement of analyte accumulation rates and selectivity

Compound-specific isotope analysis (CSIA) is a potent method for illustrating the in situ degradation of aquatic contaminants. However, its application to surface and groundwater is hindered by low contaminant concentrations, typically in the nanogram-per-litre range, requiring the processing of large water volumes. Polar organic chemical integrative samplers (POCIS) have shown promising results when combined with CSIA, yet their extended deployment time to accumulate sufficient analyte mass remains a major limitation. In our study, we addressed this issue by increasing the pore size of the polyethersulfone membrane (PES) from 0.1 to 8 μ m. This resulted in significant increases in the mass accumulation rates of atrazine (3.5-fold), S-metolachlor (3.4-fold), and boscalid (3.0-fold). Importantly, the larger pore sizes did not compromise isotopic integrity, with Δ δ 13 C ≤ + 0.4 ± 0.1 ‰ and Δ δ 15 N ≤ - 0.6 ± 0.4 ‰, both within accepted uncertainties. Additionally, we observed an enhanced selectivity of the larger pores towards the target analytes over humic acids, whereas no significant increase in (bio)fouling potential was detected for the 8 μ m membrane, as demonstrated by gravimetric analysis, SEM measurements, mass accumulation rates, and isotope ratios of fouled and unfouled POCIS. Our findings show that increasing the membrane pore size from 0.1 to 8 μ m reduces deployment time and expedites the accumulation of analyte mass required for gas chromatography isotope ratio mass spectrometry, offering a promising method to expand CSIA for low-concentration pesticide analysis in the field.

Systematic evaluation of sampling rate influences and variability in POCIS using meta-analysis and quantitative structure property relationship (QSPR)

Despite the significant benefits of aquatic passive sampling (low detection limits and time-weighted average concentrations), the use of passive samplers is impeded by uncertainties, particularly concerning the accuracy of sampling rates. This study employed a systematic evaluation approach based on the combination of meta-analysis and quantitative structure-property relationships (QSPR) models to address these issues. A comprehensive meta-analysis based on extensive data from 298 studies on the Polar Organic Chemical Integrative Sampler (POCIS) identified essential configuration parameters, including the receiving phase (type, mass) and the diffusion-limiting membrane (type, thickness, pore size), as key factors influencing uptake kinetic parameters. The incomplete availability of these details across studies potentially impacts data reproducibility and comparability. The subsequent meta-regression and subgroup analysis were performed to reveal the most significant factors contributing to sampling rate variability and inter-study heterogeneity. The flow rate and octanol-water partitioning (Kow or pH-dependent Dow) were identified from all environmental factors and chemical properties. Furthermore, the impact of chemical properties on the sampling rates of POCIS was predicted by Quantitative Structure-Property Relationship (QSPR) models using 2D descriptors and random forest regression. The analysis highlighted that the electrotopological state and molecular mass are the most important chemical properties influencing the sampling rate. This study systematically unraveled the most important impact factors on reliable estimates of passive sampling rates, and these causes of uncertainty should be further considered in aquatic monitoring and assessment with passive samplers.

Diffusive gradients in thin-films (DGT) for in situ measurement of neonicotinoid insecticides (NNIs) in waters

Neonicotinoid insecticides (NNIs) are among the most widely-used insecticides, although their threat to non-target organisms has attracted attention in recent years. In this study, a diffusive gradient in thin-films (DGT) passive sampling technique was developed for in situ monitoring of time-weighted average (TWA) concentrations of NNIs in groundwater and wastewater. Systematic studies demonstrated that DGT with HLB as binding gels (HLB-DGT) is suitable for quantitative sampling of NNIs under a wide range of conditions, independent of pH (5-9.5), ionic strength (0.001-0.5 M) and dissolved organic matter (0-10 mg/L). The HLB-DGT performance was also independent of the typical groundwater ionic environments. The thicknesses of in-situ measured diffusive boundary layer were 0.35 and 0.25 mm in the groundwater and effluent, respectively. HLB-DGT can provide TWA concentrations over 14-18 days' deployment with linear uptake in both groundwater and wastewater. Concentrations and occurrence patterns of NNIs obtained by HLB-DGT were consistent with those measured from grab samples. The median TWA concentration of NNIs was 4.42 ng/L in water from the largest urban lake of China (the Tangxun Lake) in winter, with wastewater discharge being the main potential source. The reliability and stability of the HLB-DGT for measuring NNIs in the groundwater and surface water were confirmed and can be used to improve understanding of the occurrence and fate of NNIs in aquatic environment.

Active and passive sampling techniques in headwater streams to characterize acesulfame-K, pharmaceutical and phosphorus contamination from on-site wastewater disposal systems in Canadian rural hamlets

On-site wastewater disposal systems have been identified as a source of contamination for nutrients and emerging contaminants (ECs), such as artificial sweeteners and pharmaceutical compounds. The passive sampling technique Polar Organic Chemical Integrative Sampler (POCIS) and phosphorus sampler (P-Trap) have been widely used for tracking polar organic contaminants and total dissolved phosphorus in environmental waters such as surface water and wastewater. However, limited studies have been conducted on application of passive sampling techniques to track contamination in headwater streams impacted by on-site wastewater disposal systems. In this study, active sampling (discrete samples) and passive sampling (P-Trap and POCIS) techniques were applied in upstream and downstream locations at three rural hamlets to compare and track the contamination of total dissolved phosphorus (TDP) and seven ECs, including six pharmaceuticals and one artificial sweetener acesulfame-K (ACE-K), in the shallow headwater streams of rural hamlets in southern Ontario, Canada that exclusively rely on septic systems for wastewater disposal. Results show that POCIS and P-Trap yielded comparable time-weighted average (TWA) concentrations of target ECs and TDP, respectively, to mean concentrations of discrete samples during the seasonal (spring, summer, and fall) and two-week intensive study periods. Field-derived sampling rates (Rs-field) of target contaminants compared well to literature-reported values indicating POCIS and P-Trap were applicable in determining the concentrations of target contaminants in the investigated streams, even though some environmental factors, such as dry stream conditions and fouling, occurred during the sampling period. The low but stable Rs-field of ACE-K (∼0.001 L d-1) from this study indicates consistency in application of POCIS for capturing ACE-K. The results of this study provide insight into the confidence and limitations for using POCIS and P-traps to track ECs and TDP in shallow headwater streams impacted by septic systems.

Comparison of chemical contaminant measurements using CLAM, POCIS, and silicone band samplers in estuarine mesocosms

Discrete water samples represent a snapshot of conditions at a particular moment in time and may not represent a true chemical exposure caused by changes in chemical input, tide, flow, and precipitation. Sampling technologies have been engineered to better estimate time-weighted concentrations. In this study, we consider the utility of three integrative sampling platforms: polar organic chemical integrative sampler (POCIS), silicone bands (SBs), and continuous, low-level aquatic monitoring (CLAM). This experiment used simulated southeastern salt marsh mesocosm systems to evaluate the response of passive (POCIS, SBs) and active sampling (CLAM) devices along with discrete sampling methodologies. Three systems were assigned to each passive sampler technology. Initially, all tanks were dosed at nominal (low) bifenthrin, pyrene, and triclosan concentrations of 0.02, 2.2, and 100 µg/L, respectively. After 28 days, the same treatment systems were dosed a second time (high) with bifenthrin, pyrene, and triclosan at 0.08, 8.8, and 200 µg/L, respectively. For passive samplers, estimated water concentrations were calculated using published or laboratory-derived sampling rate constants. Chemical residues measured from SBs resulted in high/low ratios of approximately 2x, approximately 3x, and 1x for bifenthrin, pyrene, and triclosan. A similar pattern was calculated using data from POCIS samples (~4x, ~3x, ~1x). Results from this study will help users of CLAM, POCIS, and SB data to better evaluate water concentrations from sampling events that are integrated across time. Integr Environ Assess Manag 2024;20:1384-1395. © 2024 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals LLC on behalf of Society of Environmental Toxicology & Chemistry (SETAC).

Pharmaceutical and pesticide mixtures in a Mediterranean coastal wetland: comparison of sampling methods, ecological risks, and removal by a constructed wetland

Pharmaceuticals and pesticides can be considered hazardous compounds for Mediterranean coastal wetland ecosystems. Although many of these compounds co-occur in environmental samples, only a few studies have been dedicated to assessing the ecotoxicological risks of complex contaminant mixtures. We evaluated the occurrence of 133 pharmaceuticals and pesticides in 12 sites in a protected Mediterranean wetland, the Albufera Natural Park (ANP), based on conventional grab sampling and polar organic chemical integrative samplers (POCIS). We assessed acute and chronic ecological risks posed by these contaminant mixtures using the multi-substance Potentially Affected Fraction (msPAF) approach and investigated the capacity of a constructed wetland to reduce chemical exposure and risks. This study shows that pharmaceuticals and pesticides are widespread contaminants in the ANP, with samples containing up to 75 different compounds. POCIS samplers were found to be useful for the determination of less predictable exposure profiles of pesticides occurring at the end of the rice cultivation cycle, while POCIS and grab samples provide an accurate method to determine (semi-)continuous pharmaceutical exposure. Acute risks were identified in one sample, while chronic risks were determined in most of the collected samples, with 5-25% of aquatic species being potentially affected. The compounds that contributed to the chronic risks were azoxystrobin, ibuprofen, furosemide, caffeine, and some insecticides (diazinon, imidacloprid, and acetamiprid). The evaluated constructed wetland reduced contaminant loads by 45-73% and reduced the faction of species affected from 25 to 6%. Our study highlights the need of addressing contaminant mixture effects in Mediterranean wetlands and supports the use of constructed wetlands to reduce contaminant loads and risks in areas with high anthropogenic pressure.

Tracing the attenuation of fipronil and its transformation products from a rice paddy field to receiving rivers using polar organic chemical integrative samplers

Irrational use of fipronil for rice pest control often occurred, resulting in high concentrations of fipronil and its transformation products (TPs) (collectively termed fiproles) in aquatic sediment, calling for a better understanding of the migration and transformation of fipronil in surface water as well as efficient methods for source identification. Herein, the fate and transport of fiproles from a paddy field to receiving rivers were assessed in Poyang Lake basin, Jiangxi, China using polar organic chemical integrative samplers with mixed-mode adsorbents (POCIS-MMA). Average concentrations of fiproles in water were 6.16 ± 6.32 ng/L, with median, minimum, and maximum values being 2.99 ± 0.67, 0.40 ± 0.08, and 18.6 ± 3.1 ng/L, respectively. In all samples, over half of fiproles (55.9 %-90.8 %) presented in the form of TPs and fipronil desulfinyl was the dominant TP. Two approaches were applied for source identification, including the change of molar concentration ratios of fipronil to its TPs and the relative attenuation values of fiproles normalized to a reference compound (acetamiprid) that was stable in aquatic environment. While the paddy field upstream was the main source of waterborne fiproles, additional input sources in the downstream region were identified. The present study indicated that the combination of attenuation of molar concentration ratios of micro-pollutants to their respective TPs and relative attenuation values of micro-pollutants' concentrations normalized to a reference compound measured by POCIS is an effective means to study the migration and transformation of micro-pollutants in field.

Examining the applicability of polar organic chemical integrative sampler for long-term monitoring of groundwater contamination caused by currently used pesticides

The possibilities of expanding a groundwater quality monitoring scheme by passive sampling using polar organic chemical integrative sampler (POCIS) comprising HLB sorbent as the receiving phase were explored. Passive sampling and grab sampling were carried out simultaneously in the regions with vulnerable groundwater resources in Slovakia, between 2013 and 2021. For 27 pesticides and degradation products detected both in POCIS and the grab samples, in situ sampling rates were calculated and statistically evaluated. The limited effectiveness of the receiving phase in POCIS for sampling polar or ionized compounds was confirmed through a comparison of the medians of compound-specific sampling rates. For the majority of the monitored compounds the median sampling rates varied between 0.01 and 0.035 L/day. In some cases, the actual in situ values could be confirmed by parallel exposure of POCIS and silicone rubber sheet employed to obtain a benchmark for maximum attainable sampling rate. Sampling site and sampling period appear to have also some influence on the sampling rates, which was attributed in part to the groundwater velocity varying in both space and time. The influence of physico-chemical parameters (temperature, pH, electrolytic conductivity) remains mostly questionable due to the naturally limited ranges of recorded values over the entire duration of the study. Concentrations of pollutants in POCIS could be used for predicting time weighed average concentrations in water, provided the sampling rates were known and relatively constant. Generally, the compound-specific sampling rate cannot be considered constant due to a combination of naturally varying environmental factors that influence the actual in situ sampling rate. The relative standard deviation of concentration data from POCIS exposed in triplicates varied between approx. 5 %-50 %. Utilizing exploratory data analysis approach and tools enabled us to obtain a relatively complex picture of the situation and progress regarding pesticide pollution of groundwater in the monitored areas.

Risk assessment of a Brazilian urban population due to the exposure to pyrethroid insecticides during the COVID-19 pandemic using wastewater-based epidemiology

Pyrethroids are synthetic insecticides commonly used in agriculture and homes due to their low toxicity to mammals and effectiveness at low doses. However, exposure to pyrethroids can cause various symptoms, depending on the route of exposure. To measure human exposure to pyrethroids, researchers used wastewater-based epidemiology (WBE) with polar organic chemical integrative samplers (POCIS) sampling. This approach is a cost-effective and efficient way to assess exposure to pyrethroids. The study aimed to evaluate the exposure of an urban population in Brazil to pyrethroids during the COVID-19 pandemic using WBE with POCIS sampling. Researchers analyzed 3-phenoxybenzoic acid (3-PBA) in wastewater using passive sampling with POCIS, which was extracted with methanol and analyzed using UPLC-MS/MS. The range of CTWA concentrations of 3-PBA in wastewater was 24.3-298.2 ng L-1, with a mean value of 134 ± 76.5 ng L-1. The values were used to estimate the exposure of the population to pyrethroid insecticides. Three different conversion factors were applied to determine the range of exposure to at least 20 different pyrethroid insecticides. The exposure values ranged from 18.08 to 1441.49 mg day-1 per 1000 inhabitants. The toxicological risk posed to the exposed population was evaluated by calculating the WBE toxicological level (WBE-TL). Lambda-cyhalothrin was used as a reference for risk assessment, and the WBE-TL values for lambda-cyhalothrin ranged from 0.5 to 8.29 (considering the high CF). We compared mobility trends to 3-PBA exposure during the COVID-19 pandemic. The study highlighted the effectiveness of POCIS sampling in WBE and provided useful information for policymakers and regulatory agencies. POCIS sampling has practical advantages, including analyte pre-concentration, low operational cost, and ease of use. Overall, the study shows the importance of monitoring and understanding the exposure of the population to pyrethroid insecticides, especially during the pandemic when people may be spending more time at home.

Analysis of a Passive Sampling Device to Assess the Behavior of Per- and Polyfluoroalkyl Substances in Sediments

Per- and polyfluoroalkyl substances (PFAS) are an emerging class of compounds that cause health and environmental problems worldwide. In aquatic environments, PFAS may bioaccumulate in sediment organisms, which can affect the health of organisms and ecosystems. As such, it is important to develop tools to understand their bioaccumulation potential. In the present study, the uptake of perfluorooctanoic acid (PFOA) and perfluorobutane sulfonic acid (PFBS) from sediments and water was assessed using a modified polar organic chemical integrative sampler (POCIS) as a passive sampler. While POCIS has previously been used to measure time-weighted concentrations of PFAS and other compounds in water, in our study, the design was adapted for analyzing contaminant uptake and porewater concentrations in sediments. The samplers were deployed into seven different tanks containing PFAS-spiked conditions and monitored over 28 days. One tank contained only water with PFOA and PFBS, three tanks contained soil with 4% organic matter, and three tanks contained soil combusted at 550 °C to minimize the influence of labile organic carbon. The uptake of PFAS from the water was consistent with previous research using a sampling rate model or simple linear uptake. For the samplers placed in the sediment, the uptake process was explained well using a mass transport based on the external resistance from the sediment layer. Uptake of PFOS in the samplers occurred faster than that of PFOA and was more rapid in the tanks containing the combusted soil. A small degree of competition was observed between the two compounds for the resin, although these effects are unlikely to be significant at environmentally relevant concentrations. The external mass transport model provides a mechanism to extend the POCIS design for measuring porewater concentrations and sampling releases from sediments. This approach may be useful for environmental regulators and stakeholders involved in PFAS remediation. Environ Toxicol Chem 2023;42:2171-2183. © 2023 SETAC.

Determination of the Isotopic Composition of Aqueous Mercury in a Paddy Ecosystem Using Diffusive Gradients in Thin Films

Measuring the isotopic composition of Hg in natural waters is challenging due to the ultratrace level of aqueous Hg (ng L-1). At least 5 ng of Hg mass is required for Hg isotopic analysis. Given the low Hg concentration in natural waters, a large volume of water (>10 L) is typically needed. The conventional grab sampling method is time-consuming, laborious, and prone to contamination during transportation and preconcentration steps. In this study, a DGT (diffusive gradients in thin films) method based on aminopropyl and mercaptopropyl bi-functionalized SBA-15 nanoparticles was developed and extended to determine the concentration and isotopic composition of aqueous Hg for the first time. The results of laboratory analysis showed that Hg adsorption by DGT induces ∼ -0.2‰ mass-dependent fractionation (MDF) and little mass-independent fractionation (MIF). The magnitude of MDF exhibits a dependence on the diffusion-layer thickness of DGT. Since Hg-MDF can occur in a broad range of environmental processes, monitoring the δ202Hg of aqueous Hg using the DGT method should be performed with caution. Field results show consistent MIF signatures (Δ199Hg) between the DGT and conventional grab sampling method. The developed DGT method serves as a passive sampling method that effectively characterizes the MIF of Hg in waters to understand the biogeochemical cycle of Hg at contaminated sites.

Calibration comparison between two passive samplers -o-DGT and POCIS- for 109 hydrophilic emerging and priority organic compounds

The Polar Organic Chemical Integrative Samplers (POCIS) is the most widely used passive sampler for hydrophilic compounds, but unsuitable for certain ionic organic contaminants. The Diffusive Gradient in Thin-Film technique (o-DGT) has shown positive results for both ionic and hydrophilic compounds. However, a calibration step is now needed to evaluate kinetic constant of accumulation for a wide range of molecules. In this study, o-DGT and POCIS were compared for the sampling of three families of micropollutants of potential risk to aquatic environments: 53 pesticides, 36 pharmaceuticals and 20 hormones. A calibration experiment was conducted to compare the kinetic models and constants from a scientific and practical perspective. The results are discussed in a single table that summarizes the performance of both passive samplers for the 109 compounds of interest. The advantage of o-DGT is that it allows linear accumulation for 72 compounds versus only 33 with POCIS. The mean times to equilibrium obtained with o-DGT are higher than those obtained with POCIS. These results confirm that the presence of a diffusion gel delays the achievement of equilibrium during compound accumulation. Therefore, o-DGT can be considered for situations where POCIS cannot be used due to non-linear accumulation over a typical 14-day deployment period. However, overall sampling rates and mass transfer coefficients also appear reduced with o-DGT, which is explained by the smaller exchange surface area, as well as the consideration of an additional diffusive layer in this device. This paper also showed that the most appropriate membrane to sample polar compounds with o-DGT was a polyethersulfone polymer with a pore size of 5 μm.

Development of a New Method to Estimate the Water Purification Efficiency of Bulk-Supported Nanosorbents under Realistic Conditions

The direct use of nanosorbents for water purification is limited due to their aggregation and the lack of techniques for their recovery from natural waters. To overcome these problems, the affixation of nanomaterials onto bulk, non-mobile supports has been proposed. However, a method to simulate the efficiency of these sorbents under realistic conditions is still not available. To address this need, this work describes a method for evaluating the sorption efficiency of nanosorbent materials incorporated on bulk supports under non-equilibrium conditions. The method combines the principles of passive sampling, an environmental monitoring technique that is based on passive diffusion of dissolved contaminants from water to a sorbent, with batch sorption experiments that measure sorption under equilibrium conditions, to determine the parameters associated with water purification. These parameters are the maximum sorption capacity of the sorbent and the sampling rate, which is the volume of contaminated water treated per unit of time. From these variables, the deployment time of the sorbent until reaching saturation is proposed as an alternative indicator of sorbent efficiency. As proof-of-principle, the removal of oxyanions from a Zr-metal-organic framework (MOR−1) immobilized on cotton textiles was investigated. The results show that the sorption capacity under passive diffusion uptake conditions, is approximately 20 mg/g for As(VI) and 36 mg/g Se(IV), which is 10 to 30 times lower compared to that determined in batch sorption studies, indicating that conventional equilibrium sorption overestimates the efficiency of the sorbents under realistic conditions. The application of the method to a worst-case scenario, involving the severe contamination of freshwaters with arsenate species, is also demonstrated.

Development of a New Polar Organic Chemical Integrative Sampler for 1,4-dioxane Using Silicone Membrane as a Diffusion Barrier

Efficient monitoring methods must be developed for 1,4-dioxane, which is suspected to be carcinogenic to humans and is highly mobile in aquatic environments. In this regard, polar organic chemical integrative samplers (POCIS) have been utilized extensively as passive samplers for determining time-weighted average concentrations of hydrophilic organic compounds. However, POCIS are difficult to apply to extremely hydrophilic known organic compounds with negative log octanol-water partition coefficient (K_ow ) values due to their limited kinetic sampling time. Using an activated carbon-based sorbent with a high adsorption capacity and a bilayer of silicone and polyethersulfone membranes that inhibit mass transfer to the sorbent, we developed a POCIS device to measure 1,4-dioxane (log K_ow -0.27) in the present study. Permeation and field calibration tests demonstrated that the use of silicone membranes effectively reduces the water-to-sorbent mass transfer rate. The sampling rate and kinetic sampling period determined by field calibration tests were 1.4 ml day^-1 and >14 days, respectively. Finally, the developed POCIS device was applied to a landfill treatment plant to determine the 1,4-dioxane concentrations. Environ Toxicol Chem 2023;42:296-302. © 2022 SETAC.

Implications of polar organic chemical integrative sampler for high membrane sorption and suitability of polyethersulfone as a single-phase sampler

Polar organic chemical integrative sampler (POCIS) contains sorbent, which is typically enclosed between two polyethersulfones (PES) membranes. A significant PES uptake is reported for many contaminants, yet, aqueous concentration is mainly correlated with the sorbent uptake using first-order kinetics. Under high PES sorption, the first-order kinetics often provide erroneous sampling rate for the sorbent phase due to increased membrane resistance. This work evaluated the uptake of four high PES sorbing chemicals, i.e., three Cl- and CH₃-substituted nitrobenzenes and one chlorinated aniline using POCIS and the potential of a single-phase PES sampler using laboratory experiments. POCIS calibration results demonstrated that both sorbent and membrane had similar affinity for the target compounds. A rapid PES sorption occurred in the earlier days (<7 days) followed by a gradual increase in the PES phase concentration (equilibrium not achieved after 60 days). Especially, the membrane was the primary sink for 3,4-dichloroaniline and 3,4-dichloronitrobenzene for up to 14 and 31 days, respectively. On the other hand, the single-phase PES sampler showed similar mass uptake as POCIS and reached equilibrium within 19 days under static condition, indicating its potential suitability in the equilibrium regime. PES-water partition coefficient of the target compounds was between 1.2 and 6.5 L/g. Finally, we present a poly-parameter linear-free energy relationship (pp-LFER) using published data to predict the PES-water partition coefficients. The pp-LFER models showed moderate predictability as indicated by R²_adj values between 0.7 and 0.9 for both internal and external data set consisting of a wide range of hydrophobic and hydrophilic compounds (-0.1 ≤ logK_OW ≤ 7.4). The proposed pp-LFER model can be used to screen high PES-sorbing chemicals to increase the reliability and accuracy of aqueous concentration prediction from POCIS sampling and to select the most appropriate sampling approach for new compounds.

A new monitoring approach for sustainability assessment of subsurface utilities gasket materials against gasoline and chlorinated solvents: Field evaluation and model development

Once installed, underground concrete pipes with rubber gaskets might be exposed to contaminated soil and groundwater. A pipe material monitoring capsule (PMMC) has been developed to evaluate volatile organic compounds (VOCs) breaking through three types of pipe gaskets; Neoprene, Buna-N, and Viton. The PMMCs were deployed in three contaminated sites: two with gasoline and one with chlorinated solvent (CS). A 3-D field-domain numerical model has been developed for each site to calibrate equivalent hydraulic parameters of each gasket material (k_e, D) against benzene and PCE diffusion. The calibrated parameters were then used to compute the concentrations as well as rate of breakthrough of the two study contaminants. A protocol was developed for installing/retrieval of PMMCs to monitor PCE and benzene mass breaking through the gasket material with time. Employing PMMC, benzene concentrations breaking through the Neoprene and Buna-N after 4 months were approximately 70% and 60% respectively of the monitoring wells concentration. The corresponding value for PCE breakthrough after 4 months was 60% for both the Neoprene and Buna-N. Both gasket materials of Neoprene and Buna-N yielded similar performances, including higher rate of contaminant breakthrough compared to Viton. A nonlinear relationship of mass breaking through the gaskets of benzene and PCE with time was discerned from the modeling and field data.

A Review on Polyethersulfone Membranes in Polar Organic Chemical Integrative Samplers: Preparation, Characterization and Innovation

The membranes in polar organic chemical integrative samplers (POCIS) enclose the receiving sorbent and protect it from coming into direct contact with the environmental matrix. They have a crucial role in extending the kinetic regime of contaminant uptake, by slowing down their diffusion between the water phase and the receiving phase. The drive to improve passive sampling requires membranes with better design and enhanced performances. In this review, the preparation of standard polyethersulfone (PES) membranes for POCIS is presented, as well as methods to evaluate their composition, morphology, structure, and performance. Generally, only supplier-related morphological and structural data are provided, such as membrane type, thickness, surface area, and pore diameter. The issues related to the use of PES membranes in POCIS applications are exposed. Finally, alternative membranes to PES in POCIS are also discussed, although no better membrane has yet been developed. This review highlights the urge for more membrane characterization details and a better comprehension of the mechanisms which underlay their behavior and performance, to improve membrane selection and optimize passive sampler development.

Carbon nanotube-passive samplers as novel tools for sampling and determining micropollutants in the aquatic environment

Passive sampling is an interesting and cost-effective strategy for the quantification of micropollutants in the aquatic environment. When combined especially with a sensitive analytical method such as liquid chromatography coupled with triple quadrupole mass spectrometry (LC-MS/MS), the use of passive sampling devices (PSDs) enables long-term and reliable determination of a wide range of chemicals. In this study, carbon nanotubes (CNTs) were used as an innovative sorbent in POCIS-like samplers (Polar Organic Chemical Integrative Sampler). The developed CNTs-PSDs were calibrated by the flow-through method and the obtained sampling rates (R_s) of analytes were compared with the previously obtained R_s values using the semi-static method. Subsequently, passive samplers were placed in the Baltic Sea, the Nogat River, and the Sztumskie Pole Lake in order to sample and concentrate 28 chemical compounds belonging to the group of contaminants of emerging concern (CECs). For the first time, the effectiveness of the use of CNTs-PSDs in the field was proven by the quantification of carbamazepine, diclofenac, p-nitrophenol, bisphenol A, 3,5-dichlorophenol, 17-β-estradiol, 17-α-ethinylestradiol and metoprolol in the tested surface waters. The obtained time-weighted average (TWA) concentrations of analytes ranged from 0.22 ± 0.12 ng/L (for metoprolol in the Nogat River) to 32.1 ± 2.4 ng/L (for bisphenol A in the Sztumskie Pole Lake). More importantly, CNTs-PSDs determined a greater amount of micropollutants than grab sampling and solid-phase extraction (SPE), which proves the advantage of passive sampling over grab sampling, especially when monitoring contaminants in the aquatic environment at low concentration levels.

An optimized processing method for polar organic chemical integrative samplers deployed in seawater: Toward a maximization of the analysis accuracy for trace emerging contaminants

Passive sampling of emerging contaminants (ECs) in seawater represents a challenge in environmental monitoring. A specific protocol for Polar Organic Chemical Integrative Sampler (POCIS) processing may be necessary when dealing with marine applications, due to the peculiarity of the considered matrix. Herein, both the instrumental LC-MS/MS analysis and the sampler processing for the determination of 22 ECs in seawater were carefully optimized. The study entailed a test simulating POCIS sorbent exposure to seawater as well as the processing of replicated field POCIS with different elution solvents. The final method involved washing the sorbent with water, to eliminate most salts, and a two-step elution, by using methanol and a small volume of a dichloromethane-isopropanol mixture. With this protocol, recoveries between 58 and 137% (average 106%) were obtained for most analytes, including non-steroidal anti-inflammatory drugs, UV-filters, perfluorinated substances and caffeine. Still, the protocol was not suitable for very hydrophilic compounds (recovery under 20% for artificial sweeteners and the pharmaceutical salbutamol), which also showed remarkable ion suppression (matrix effects in the range 4-46%). For all other chemicals, the matrix effects were in the range 67-103% (average 86%), indicating satisfactory accuracy. Also, the overall method showed high sensitivity (detection limits in the range 0.04-9 ng g^-1 of POCIS sorbent) and excellent specificity, thanks to the monitoring of two "precursor ion-product ion" MS transitions for identity confirmation. The method was applied to samplers deployed in the Ligurian coast (Italy), detecting caffeine, bisphenol A, ketoprofen and two UV-filters as the most concentrated in the POCIS sorbent.

Polar organic chemical integrative samplers as an effective tool for chemical monitoring of surface waters - Results from one-year monitoring in France

In an effort to support European Union Water Framework Directive goals, we have set up a national demonstrator project to identify the advantages and limitations of passive samplers for regulatory monitoring of polar contaminants in surface waters. Here we carried out successive 14 day-deployments of polar organic chemical integrative samplers (POCIS) for one year at three sites. In parallel, we used the passive sampler deployment/retrieval operations to collect spot water samples for comparative analysis. We observed that frequency of quantification was significantly higher in POCIS than spot samples for 29 contaminants, similar for 15, and lower for one, because POCIS lowered the limits of quantification for most contaminants (median value factor of 11). We built a database of sampling rates (Rs) according to quality indices to convert concentrations in POCIS to concentrations in water (23 contaminants with a high-quality median Rs value, 20 with an approximate Rs and two with no usable Rs). Several phenomena were observed over one-year monitoring period. For example, after a flood episode, dilution phenomenon in rivers is correctly observed by using POCIS sampling whereas significant concentration increased due to soil leaching is observed with both passive and spot sampling. Cases of episodic contamination that were missed by spot sampling were observed with POCIS as it was able to capture contamination of short duration but sufficient intensity. Contamination by pharmaceuticals was found to come from wastewater treatment plant discharges and showed relatively little variation over the course of the year in both POCIS and spot samples. POCIS enables more reliable annual monitoring of pesticide and pharmaceutical contamination than spot sampling. Furthermore, POCIS also improves the environmental quality standards based assessment of chemical status and on annual average concentrations compared to spot sampling. This study demonstrates the value and practicability of POCIS-based chemical monitoring for use in regulatory control networks.

Environmental Characterization of Underwater Munitions Constituents at a Former Military Training Range

As a result of military activities, unexploded ordnance and discarded military munitions are present in underwater environments, which has resulted in the release of munitions constituents including the high explosives 2,4,6-trinitrotoluene (TNT) and hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), along with their primary degradation products, to the water column and adjacent sediments. The present study focused on the characterization of underwater exposure and concentrations of energetics such as TNT and RDX at the former Vieques Naval Training Range at Bahia Salina del Sur (Vieques, Puerto Rico, USA), a bay with documented high incidence of munitions. In situ passive sampling using polar organic chemical integrative samplers (POCIS) was used for the detection and quantification of constituents in water at target locations approximately 15 to 30 cm from 15 individual potentially leaking munitions, and also at 15 unbiased locations approximately evenly spaced across the Bay. For comparison with POCIS-derived concentrations, grab samples were taken at the POCIS target locations. The POCIS-derived and averaged grab samples agreed within a factor of 3. When detected, munitions constituent concentrations (primarily TNT and RDX) were observed at ultratrace concentrations (as low as 4 ng/L for RDX), except 30 cm from one General Purpose bomb where the TNT concentration was 5.3 µg/L, indicating that low-level contamination exists at Bahia Salina del Sur on a very localized scale despite the relatively high density of munitions, similar to previously reported results for other munitions sites around the world. Sediment and porewater sampled at 4 stations where munitions constituents were detected in the water column had concentrations below detection (approximately 5 µg/kg and 5 ng/L, respectively), suggesting that the sediment was not a sink for these constituents at those locations. Environ Toxicol Chem 2022;41:275-286. © 2021 SETAC. This article has been contributed to by US Government employees and their work is in the public domain in the USA.

Passive sampling and in vitro assays to monitor antiandrogens in a river affected by wastewater discharge

Pharmaceuticals and personal care products, antibiotics, estrogens, and antiandrogens are found widely in aquatic environments. Monitoring studies by sampling surface water and effluents of wastewater treatment plants (WWTPs) have been conducted recently to monitor antiandrogens, which, along with estrogens, cause endocrine disruption. However, few studies have investigated antiandrogenic activity (AA) combined with a chemical analyses of emerging antiandrogens. Therefore, we analyzed the presence and persistence of 12 types of antiandrogens, atrazine, and carbamazepine using grab sampling and polar organic chemical integrative sampler (POCIS) along a river affected by WWTP discharges. Water and sediment samples were collected from the WWTP effluent (WW), as well as upstream (US) and downstream (DS) of the WWTP. We detected only tebuconazole, triclosan, propiconazole, and fluconazole during the two sampling campaigns in 2016 and 2017. Grab sampling of the site WW detected tebuconazole (7-77 ng/L), propiconazole (5-47 ng/L), and fluconazole (6-45 ng/L). However, the concentrations in the river water were below the detection limits. Nevertheless, fluconazole and triclosan were detected by POCIS in the site WW (45.7 and 26.8 ng/L, respectively) and all river samples ranges of 0.3-9.3 and 2.4-3.7, respectively. This detection was attributed to the limit of quantification of POCIS being lower than that of grab sampling. Nilutamide and triclosan were detected in the river sediment, suggesting that their concentrations in the water column were at least partly attenuated through sediment sorption. We also observed AA by analyzing POCIS extracts with the yeast androgen screen assay. The highest AA was found in the site WW and it was still observable several kilometers downstream of the point of discharge despite decreasing. Therefore, the WWTP effluent was most likely contributor to the persistent AA in the river.

Unravelling the role of membrane pore size in polar organic chemical integrative samplers (POCIS) to broaden the polarity range of sampled analytes

Polar organic chemical integrative samplers (POCIS) are widely used in their standard configuration for sampling contaminants in water bodies. A wider polyethersulfone (PES) membrane pore size was employed in POCIS exposed in a static calibration experiment to investigate the uptake of 21 emerging contaminants ranging from hydrophilic (perfluoroalkyl compounds, xanthines, an artificial sweetener) to more hydrophobic compounds (pharmaceuticals, oestrogens, UV filters). Compared to standard POCIS with 0.1-µm pore size PES membranes, the POCIS with 5-µm pore size PES membranes did not increase sampling rates for compounds of relatively low and mid-hydrophobicity. However, the uptake of more hydrophobic and anionic compounds, which either poorly diffuse through or are retained within the standard 0.1-µm PES membrane, showed a marked increase. This led to the first ever recorded sampling rates for triclosan (0.249 L day^-1) and two UV filters (0.075-0.123 L day^-1). Based on these results, more attention should be placed on the choice of the appropriate membrane for each POCIS application. The most suitable configuration depends on the studied compound physico-chemical characteristics-such as the polarity and the compound membrane-to-sorbent partitioning coefficient-but also on the site conditions (deployment time, fouling, flow variations, et.).

Point or non-point source: Toxicity evaluation using m-POCIS and zebrafish embryos in municipal sewage treatment plants and urban waterways

Municipal sewage treatment plants (STPs) have been regarded as an important source of organic contaminants in aquatic environment. To assess the impact of STPs on occurrence and toxicity of STP-associated contaminants in receiving waterways, a novel passive sampler modified from polar organic chemical integrative sampler (m-POCIS) was deployed at the inlet and outlet of a STP and several upstream and downstream sites along a river receiving STP effluent in Guangzhou, China. Eighty-seven contaminants were analyzed in m-POCIS extracts, along with toxicity evaluation using zebrafish embryos. Polycyclic musks were the predominant contaminants in both STP and urban waterways, and antibiotics and current-use pesticides (e.g., neonicotinoids, fiproles) were also ubiquitous. The m-POCIS extracts from downstream sites caused significant deformity in embryos, yet the toxicity could not be explained by the measured contaminants, implying the presence of nontarget stressors. Sewage treatment process substantially reduced embryo deformity, chemical oxygen demand, and contamination levels of some contaminants; however, concentrations of neonicotinoids and fiproles increased after STP treatment, possibly due to the release of chemicals from perturbed sludge. Source identification showed that most of the contaminants found in urban waterways were originated from nonpoint runoff, while cosmetics factories and hospitals were likely point sources for musks and antibiotics, respectively. Although the observed embryo toxicity could not be well explained by target contaminants, the present study showed a promising future of using passive samplers to evaluate chemical occurrence and aquatic toxicity concurrently. Zebrafish embryo toxicity significantly decreased after sewage treatment, but higher toxicity was observed for downstream samples, demonstrating that urban runoff may produce detrimental effects to aquatic life, particularly in rainy season. These results highlight the relevance of monitoring nonpoint source pollution along with boosting municipal sewage treatment infrastructure.

Lab-scale investigation of the ability of Polar Organic Chemical Integrative Sampler to catch short pesticide contamination peaks

In this lab-scale study, the POCIS capacity to integrate short contamination peaks of variable intensity and duration was evaluated. POCIS were immersed for 14 days in tanks filled with tap water and spiked at different concentrations with 12 pesticides of various polarities (log K_ow = 1.1-4.7) and classes (herbicides, fungicides, and insecticides). Concentrations were kept relatively constant at 1 μg L^-1 and 5 μg L^-1, respectively, in two "background" exposure tanks. Three contamination peaks of increasing intensity and decreasing duration were simulated (10 μg L^-1 for 24 h, 40 μg L^-1 for 6 h, and 60 μg L^-1 for 1 h). This lab-scale study demonstrated that ten moderately polar compounds (2 < log K_ow < 4) showed a linear uptake, as observed in previous studies, while a non-linear model fits the data of the two most polar pesticides (log K_ow < 2). Depending on chemical polarity, some compounds exhibited a "burst effect" or "lag effect" during the first 3 days of exposure. After 14 days of exposure, contamination peaks appeared integrated for seven compounds, showing the ability of POCIS to catch very short pollution events and to provide acceptable time-weighted average concentration estimates under laboratory-controlled conditions.

Multimedia distributions and the fate of microcystins from freshwater discharge in the Geum River Estuary, South Korea: Applicability of POCIS for monitoring of microalgal biotoxins

Here, we investigated the characteristics of the environmental multimedia distribution of microcystins (MCs) introduced from freshwater discharge through the estuary dam of the Geum River. In addition, the applicability of a passive sampling device (polar organic chemical integrative sampler, POCIS) for monitoring MCs was evaluated. Surface water, suspended solids (SS), sediments, and oysters were collected from the inner and outer estuary dam. Seven MC variants were analyzed using HPLC-MS/MS. POCIS was deployed at three sites over one week, and MCs were monitored for four weeks from August to September 2019. Before POCIS was deployed in the field, compounds-specific sampling rates of MCs were determined as functions of water temperature (10, 20, and 30 °C), flow rate (0, 0.38, and 0.76 m s^-1), and salinity (0, 15, and 30 psu) in the laboratory. The sampling rates of MCs in POCIS increased significantly with increasing water temperature and flow rate, whereas salinity did not significantly affect the sampling rates between freshwater and saltwater. The MCs in the Geum River Estuary mainly existed as particulate forms (mean: 78%), with relatively low proportions of dissolved forms (mean: 22%), indicating that MCs were mainly contained in cyanobacterial cells. There was no significant correlation among the concentrations of MCs in water, SS, sediments, and oysters. Time-weighted average concentrations of MCs from POCIS were not significantly correlated with the concentrations of MCs in water and oysters. The metabolites of MCs, including MC-LR-GSH, MC-LR-Cys, MC-RR-GSH, and MC-RR-Cys, were detected in oysters (no metabolites were detected in POCIS). Overall, POCIS can be useful for monitoring dissolved MCs in the aquatic ecosystem, particularly in calculating time-weighted average concentrations, but it seems to have limitations in evaluating the contamination status of total MCs, mainly in particulate form.

Detection of anticancer drugs in wastewater effluents: Grab versus passive sampling

The occurrence of six anticancer drugs was evaluated in wastewater effluents. Several grab samples from wastewater effluent were collected throughout a year. Capecitabine, cyclophosphamide and ifosfamide were detected at concentrations ranging from 8 to 46 ng·L^-1. Capecitabine was detected in all the sampling events whereas cyclophosphamide and ifosfamide were detected less frequently. Additionally, the suitability of using pharmaceutical-polar organic chemical integrative samplers (POCIS) to monitor the target drugs in wastewater effluents was assessed. Capecitabine, ifosfamide and cyclophosphamide were detected with POCIS and showed a linear uptake over 15 days. The sampling rates, determined in situ, were used to estimate time-weighted average concentrations. A good correlation was found between the concentration of capecitabine detected with POCIS deployed during five days (32 ± 1 ng·L^-1) and the average concentrations obtained in grab samples. The use of passive samplers has advantages over grab samples: easier analysis, less time and costs associated with the analytical method. Passive samplers also provide a time-weighted information about the concentration of pollutants in the aquatic environment. However, information may be lost when the concentration of the target compounds in wastewater effluents is low and the passive samplers are deployed for a short time.

Pharmaceuticals in the marine environment: What are the present challenges in their monitoring?

During the last years, there has been a growing interest in the research focused on the pharmaceutical residues in the environment. Those compounds have been recognized as a possible threat to aquatic ecosystems, due to their inherent biological activity and their "pseudo-persistence". Their presence has been relatively few investigated in the marine environment, though it is the last receiver of the continental contamination. Thus, pharmaceuticals monitoring data in marine waters are necessary to assess water quality and to allow enhancing future regulations and management decisions. A review of the current practices and challenges in monitoring strategies of pharmaceuticals in marine matrices (water, sediment and biota) is provided through the analysis of the available recent scientific literature. Key points are highlighted for the different steps of marine waters monitoring as features to consider for the targeted substance selection, the choice of the marine site configuration and sampling strategies to determine spatio-temporal trends of the contamination. Some marine environment specific features, such as the strong dilution occurring, the complex hydrodynamic and local logistical constraints are making this monitoring a very difficult and demanding task. Thus key knowledge gap priorities for future research are identified and discussed. Suitable passive samplers to monitor pharmaceutical seawater levels need further development and harmonization. Non-target analysis approaches would be promising to understand the fate of the targeted molecules and to enhance the list of substances to analyze. The implementation of integrated monitoring through long-term ecotoxicological tests on sensitive marine species at environmental levels would permit to better assess the ecological risk of these compounds for the marine ecosystems.

Evaluation of Illicit Drug Consumption by Wastewater Analysis Using Polar Organic Chemical Integrative Sampler as a Monitoring Tool

Illicit drug abuse is a worldwide social and health problem, and monitoring illicit drug use is of paramount importance in the context of public policies. It is already known that relevant epidemiologic information can be obtained from the analysis of urban residual waters. This approach, named wastewater-based epidemiology (WBE), is based on the measurement of specific markers, resulting from human biotransformation of the target drugs, as indicators of the consumption of the compounds by the population served by the wastewater treatment installation under investigation. Drug consumption estimation based on WBE requires sewage sampling strategies that express the concentrations along the whole time period of time. To this end, the most common approach is the use of automatic composite samplers. However, this active sampling procedure is costly, especially for long-term studies and in limited-resources settings. An alternative, cost-effective, sampling strategy is the use of passive samplers, like the polar organic chemical integrative sampler (POCIS). POCIS sampling has already been applied to the estimation of exposure to pharmaceuticals, pesticides, and some drugs of abuse, and some studies evaluated the comparative performances of POCIS and automatic composite samplers. In this context, this manuscript aims to review the most important biomarkers of drugs of abuse consumption in wastewater, the fundamentals of POCIS sampling in WBE, the previous application of POCIS for WBE of drugs of abuse, and to discuss the advantages and disadvantages of POCIS sampling, in comparison with other strategies used in WBE. POCIS sampling is an effective strategy to obtain a representative overview of biomarker concentrations in sewage over time, with a small number of analyzed samples, increased detection limits, with lower costs than active sampling. Just a few studies applied POCIS sampling for WBE of drugs of abuse, but the available data support the use of POCIS as a valuable tool for the long-term monitoring of the consumption of certain drugs within a defined population, particularly in limited-resources settings.

Comparative field study on bioassay responses and micropollutant uptake of POCIS, Speedisk and SorbiCell polar passive samplers

Routine water quality monitoring is generally performed with chemical analyses of grab samples, which has major limitations. First, snapshot samples will not give a good representation of the water quality. Second, it is not sufficient to analyze only a limited number of (priority) pollutants. These limitations can be circumvented by an alternative environmental risk assessment that combines time-integrated passive sampling (PS) with effect-based methods. This study aimed to select which of three polar PS devices was best suited for effect-based monitoring strategies. In the first part of this study, Speedisk, SorbiCell and POCIS polar PS devices were compared by simultaneous deployment at five sites. Chemical analyses of 108 moderately polar compounds (-1.82 < log D < 6.28) revealed that highest number of compounds, with the widest range of log K_OW, log D and pKa, were detected in extracts of POCIS, followed by Speedisk. SorbiCell samplers accumulated the lowest numbers and concentrations of compounds, so they were not further investigated. In a follow-up study, bioassay responses were compared in extracts of POCIS and Speedisk devices deployed at eight sites. The passive sampler extracts were subjected to bioassays for non-specific toxicity, endocrine disruption, and antibiotics activities. More frequent and higher responses were induced by POCIS extracts, leading to more exceedances of effect-based trigger values for environmental risks. As POCIS outperformed Speedisk, it is better suited as PS device targeting polar compounds for semi-quantitative effect-based water quality monitoring.

In situ calibration of polar organic chemical integrative sampler (POCIS) for monitoring of pharmaceuticals in surface waters

POCIS is the most widely applied passive sampler of polar organic substances, because it was one of the first commercially available samplers for that purpose on the market, but also for its applicability for a wide range of substances and conditions. Its main weakness is the variability of sampling performance with exposure conditions. In our study we took a pragmatic approach and performed in situ calibration for a set of 76 pharmaceuticals and their metabolites in five sampling campaigns in surface water, covering various temperature and flow conditions. In individual campaigns, R_S were calculated for up to 47 compounds ranging from 0.01 to 0.63 L d^-1, with the overall median value of 0.10 L d^-1. No clear changes of R_S with water temperature or discharge could be found for any of the investigated substances. The absence of correlation of experimental R_S with physical-chemical properties in combination with the lack of mechanistic understanding of compound uptake to POCIS implies that practical estimation of aqueous concentrations from uptake in POCIS depends on compound-specific experimental calibration data. Performance of POCIS was compared with grab sampling of water in seven field campaigns comprising multiple sampling sites, where sampling by both methods was done in parallel. The comparison showed that for 25 of 36 tested compounds more than 50% of POCIS-derived aqueous concentrations did not differ from median of grab sampling values more than by a factor of 2. Further, for 30 of 36 compounds, more than 80% of POCIS data did not differ from grab sampling data more than by a factor of 5. When accepting this level of accuracy, in situ derived sampling rates are sufficiently robust for application of POCIS for identification of spatial and temporal contamination trends in surface waters.

Sampling Rate of Polar Organic Chemical Integrative Sampler (POCIS): Influence Factors and Calibration Methods

As a passive sampling device, the polar organic chemical integrative sampler (POCIS) has the characteristics of simple operation, safety, and reliability for assessing the occurrence and risk of persistent and emerging trace organic pollutants. The POCIS, allowing for the determination of time-weighted average (TWA) concentration of polar organic chemicals, exhibits good application prospects in aquatic environments. Before deploying the device in water, the sampling rate (Rs), which is a key parameter for characterizing pollutant enrichment, should be determined and calibrated accurately. However, the Rs values strongly depend on experimental hydrodynamic conditions. This paper provides an overview of the current situation of the POCIS for environmental monitoring of organic pollutants in an aquatic system. The principle and theory of the POCIS are outlined. In particular, the effect factors such as the ambient conditions, pollutant properties, and device features on the Rs are analyzed in detail from aspects of impact dependence and mechanisms. The calibration methods of the Rs under laboratory and in situ conditions are summarized. This review offers supplementary information on comprehensive understanding of mechanism and application of the POCIS. Nevertheless, the Rs were impacted by a combined effect of solute–sorbent–membrane–solution, and the influence extent of each variable was still unclear. On this basis, the ongoing challenges are proposed for the future application of the POCIS in the actual environment, for instance, the need for this device to be improved in terms of quantitative methods for more accurate measurement of the Rs.

Detection of pharmaceuticals in wastewater effluents-a comparison of the performance of Chemcatcher® and polar organic compound integrative sampler

Chemcatcher^® and POCIS passive sampling devices are widely used for monitoring polar organic pollutants in water. Chemcatcher^® uses a bound Horizon Atlantic™ HLB-L sorbent disk as receiving phase, whilst the POCIS uses the same material in the form of loose powder. Both devices (n = 3) were deployed for 21 days in the final effluent at three wastewater treatment plants in South Wales, UK. Following deployment, sampler extracts were analysed using liquid chromatography time-of-flight mass spectrometry. Compounds were identified using an in-house database of pharmaceuticals using a metabolomics workflow. Sixty-eight compounds were identified in all samplers. For the POCIS, substantial losses of sorbent (11-51%) were found during deployment and subsequent laboratory analysis, necessitating the use of a recovery factor. Percentage relative standard deviations varied (with 10 compounds exceeding 30% in both samplers) between individual compounds and between samplers deployed at the three sites. The relative performance of the two devices was evaluated using the mass of analyte sequestered, measured as an integrated peak area. The ratio of the uptake of the pharmaceuticals for the POCIS versus Chemcatcher^® was lower (1.84x) than would be expected on the basis of the ratio of active sampling areas (3.01x) of the two devices. The lower than predicted uptake may be attributable to the loose sorbent material moving inside the POCIS when deployed in the field in the vertical plane. In order to overcome this, it is recommended to deploy the POCIS horizontally inside the deployment cage.

Polymeric Nanofiber-Carbon Nanotube Composite Mats as Fast-Equilibrium Passive Samplers for Polar Organic Contaminants

To improve the performance of polymeric electrospun nanofiber mats (ENMs) for equilibrium passive sampling applications in water, we integrated two types of multiwalled carbon nanotubes (CNTs; with and without surface carboxyl groups) into polyacrylonitrile (PAN) and polystyrene (PS) ENMs. For 11 polar and moderately hydrophobic compounds (-0.07 ≤ logKOW ≤ 3.13), 90% of equilibrium uptake was achieved in under 0.8 days (t90% values) in nonmixed ENM-CNT systems. Sorption capacity of ENM-CNTs was between 2- and 50-fold greater than pure polymer ENMs, with equilibrium partition coefficients (KENM-W values) ranging from 1.4 to 3.1 log units (L/kg) depending on polymer type (hydrophilic PAN or hydrophobic PS), CNT loading (i.e., values increased with weight percent (wt %) of CNTs), and CNT type (i.e., greater uptake with carboxylated CNTs composites). During field deployment at Muddy Creek in North Liberty, Iowa, optimal ENM-CNTs (PAN with 20 wt % carboxylated CNTs) yielded atrazine concentrations in surface water with a 40% difference relative to analysis of a same-day grab sample. We also observed a mean percent difference of 30 (±20)% when comparing ENM-CNT sampler results to grab sample data collected within 1 week of deployment. With their rapid, high capacity uptake and small material footprint, ENM-CNT equilibrium passive samplers represent a promising alternative to complement traditional integrative passive samplers while offering convenience over large volume grab sampling.

Estimating 42 pesticide sampling rates by POCIS and POCIS-MIP samplers for groundwater monitoring: a pilot-scale calibration

Pesticides occur in groundwater as a result of agricultural activity. Their monitoring under the Water Framework Directive is based on only a few spot-sampling measurements per year despite their temporal variability. Passive sampling, which was successfully tested in surface water to provide a more representative assessment of contamination, could be applied to groundwater for a better definition of its contamination. However, few reliable calibration data under low water flow are available. The objective of our study thus consisted in determining sampling rates by two types of passive samplers, a POCIS (polar organic chemical integrative sampler) for polar pesticides, and a POCIS-MIP sampler based on a receiving phase of molecular imprinted polymers, specific for AMPA and glyphosate under low flow conditions as exist in groundwater. To our knowledge, this is the first time that sampling rates (sampling rate represents the volume of water from which the analyte is quantitatively extracted by the sampler per unit time) are estimated for groundwater applications. Our calibrations took place in an experimental pilot filled with groundwater and with low water flow (a few metres per day). Pesticide uptake in POCIS showed good linearity, with up to 28 days before reaching equilibrium. Two types of accumulation in POCIS were noted (a linear pattern up to 28 days, and after a time lag of 7 to 14 days). Sampling rates for 38 compounds were calculated and compared with those available in the literature or obtained previously under laboratory conditions. The values obtained were lower by a factor 1 to 14 than those estimated under stirring conditions in the literature, whereas water flow velocity (m s^-1) differed by a factor of 2000 to 10,000.

"Modern agriculture" transfers many pesticides to watercourses: a case study of a representative rural catchment of southern Brazil

The total cultivated area in Brazil reached to 62 million ha in 2018, with the predominance of genetically modified soybean and corn (36 and 17 million ha, respectively) in no-tillage systems. In 2018, 5.3 × 10⁵ Mg of active ingredient of pesticides was applied in cropfields, representing about 7.3 L of commercial product by habitant. However, the monitoring of water courses contamination by pesticides remains scarce and is based on traditional grab sampling systems. In this study, we used the grab (water) and passive sampling (Polar Organic Chemical Integrative Sampler-POCIS) to monitor pesticide contamination in the river network of a representative agricultural catchment of southern Brazil. We selected 18 sampling sites located in tributaries and in the main course of the Guaporé River, in Rio Grande do Sul State, with different land use predominance including forest, urban, and agricultural areas. Altogether, 79 and 23 pesticides were, respectively, analyzed in water and POCIS samples. The water of Guaporé River and its tributaries were highly contaminated by many pesticides, especially by four herbicides (2,4-D, atrazine, deethyl-atrazine, and simazine), three fungicides (carbendazim, tebuconazole, and epoxiconazole), and one insecticide (imidacloprid). The amount, type, and concentration of pesticides detected were completely different depending on the sampling technic used. POCIS was effective to discriminate the contamination according to the main land use of each sampling site. The monitored areas with the predominance of soybean cultivation under no-tillage tended to have higher concentrations of fungicide, while in the more diversified region, the herbicides showed higher values. The presence of five herbicides used in corn and grassland forage production was correlated with areas of integrated crop-livestock systems, in contrast to higher contamination by 2,4-D in areas of intensive production of soybean and winter cereals.

Method to Evaluate the Age of Groundwater Inputs to Surface Waters by Determining the Chirality Change of Metolachlor Ethanesulfonic Acid (MESA) Captured on a Polar Organic Chemical Integrative Sampler (POCIS)

We previously discovered a method to estimate the groundwater mean residence time using the changes in the enantiomeric ratio of metolachlor ethanesulfonic acid (MESA), (2-[(2-ethyl-6-methylphenyl)(2-methoxy-1-methylethyl)amino]-2-oxoethanesulfonic acid), a metabolite of the herbicide metolachlor. However, many grab samples would be needed for each watershed over an extended period, and this is not practical. Thus, we examined the use of a polar organic chemical integrative sampler (POCIS) deployed for 28 days combined with a modified liquid chromatography-mass spectrometry LC-MS/MS method to provide a time-weighted average of the MESA enantiomeric ratio. POCISs equipped with hydrophilic-lipophilic-balanced (HLB) discs were deployed at five sites across the United States where metolachlor was used before and after 1999 and compared the effectiveness of the POCIS to capture MESA versus grab samples. In addition, an in situ POCIS sampling rate (R_s) for MESA was calculated (0.15 L/day), the precision of MESA extraction from stored POCIS discs was determined, and the effectiveness of HLB to extract MESA was examined. Finally, using molecular modeling, the influence of the asymmetric carbon of metolachlor degradation on the MESA enantiomeric ratio was predicted to be negligible. Results of this work will be used in projects to discern the groundwater mean residence times, to evaluate the delivery of nitrate-N from groundwater to surface waters under various soil, agronomic, and land use conditions, and to examine the effectiveness of conservation practices.

Calibration and validation of a microporous polyethylene passive sampler for quantitative estimation of illicit drug and pharmaceutical and personal care product (PPCP) concentrations in wastewater influent

Wastewater-based epidemiology (WBE), the per capita normalised measurement of drugs, chemicals or metabolites in wastewater influent, relies on sampling and quantitative analysis to evaluate temporal and spatial trends of chemical consumption. Continuous, high-resolution, flow proportional composite sampling is optimal for accurate representations of chemical mass loads, but is rarely implemented, with conventional autosamplers providing relatively low frequency time or volume proportional samples. However, due to equipment or resource constraints at many wastewater treatment plants (WWTPs), even this may not be feasible. Passive sampling may provide an alternative sampling strategy. To investigate this, samplers comprising hollow, cylindrical Microporous Polyethylene Tubes (MPTs) containing polymeric sorbent phases of Strata-X and Strata-X in agarose were simultaneously deployed in a municipal WWTP influent stream. Samplers were extracted, analysed and evaluated for a range of illicit drugs and pharmaceuticals and personal care products (PPCPs) after 4, 7, 15, 21, and 29 day deployments. The MPT samplers were calibrated against 24-hour time proportional composite grab samples that were collected in parallel. Diffusion through the MPT governed uptake, reducing or eliminating the influence of external flow rates that may fluctuate unpredictably in a WWTP environment. Calibration data for six illicit drugs and fourteen PPCPs, including methamphetamine, benzoylecgonine, MDMA, codeine and carbamazepine, demonstrated linear accumulation in the samplers (R² ≥ 0.84). Derived sampling rates for these analytes ranged from 0.25 to 17 mL d^-1 for ibuprofen and verapamil, respectively. A validation study using this sampling rate data showed the MPT could effectively quantify concentrations (≥0.1 ng mL^-1) of a range of amphetamine-type stimulants, opioids and metabolites as well as nicotine, accounting for 95% of the variance in parallel composite grab sample concentrations of these compounds. The MPT sampler shows promise for providing essential monitoring data for WBE, informing future intervention and research strategies.

A new method based on diffusive gradients in thin films for in situ monitoring microcystin-LR in waters

The passive sampling method of diffusive gradients in thin-films (DGT) was developed to provide a quantitative and time-integrated measurement of microcystin-LR (MC-LR) in waters. The DGT method in this study used HLB (hydrophilic-lipophilic-balanced) material as a binding agent, and methanol as an eluent. The diffusion coefficient of MC-LR was 5.01 × 10⁻⁶ cm² s⁻¹ at 25 °C in 0.45 mm thick diffusion layer. This DGT method had a binding capacity of 4.24 μg per binding gel disk (3.14 cm²), ensuring sufficient capacity to measure MC-LR in most water matrices. The detection limit of HLB DGT was 0.48 ng L⁻¹. DGT coupled to analysis by HPLC appears to be an accurate method for MC-LR monitoring. Comparison of DGT measurements for MC-LR in water and a conventional active sampling method showed little difference. This study demonstrates that HLB-based DGT is a useful tool for in situ monitoring of MC-LR in fresh waters.

Theory and modelling approaches to passive sampling

Designs and applications of passive samplers for various environmental compartments have been broadened significantly since their introduction. Understanding the theory behind passive sampling is essential for proper development of sampling methods and for accurate interpretation of the results. Theoretical underpinnings of passive sampling have been explored using different approaches. The aim of this review is to describe passive sampling theory and modelling approaches presented in the literature in a manner that allows researchers to obtain comprehensive understanding of them and to recognize the assumptions behind each approach together with their applicability to a given passive sampling technique. A common approach originates from Whitman's two-film theory and produces an exponential model that describes the entire passive sampling process. This approach, however, is based on several assumptions including linear exchange kinetics between the sampled medium and the passive sampler. Two-phase air passive samplers with a well-defined barrier are commonly modeled based on the zero-sink assumption, which assumes efficient trapping of analytes in the receiving phase. This assumption may become invalid under various scenarios; consequently, other approaches to modelling have been introduced including simulation of the sampling process by approximate temporal-steady states in hypothetical segments in the adsorption phase. Another approach uses dynamic models to determine accumulation of analytes in passive samplers. Dynamic models are capable of describing mass accumulation in the passive sampler, its transient response, and its response to fluctuations in environmental concentrations. Finally, empirically calibrated models, attempting to simplify the process of passive sampling rate determination, are also presented. In general, dynamic models are used to establish a profound understanding of the sampling process and analyse the applicability of the simpler models and their assumptions, while the simplified models are desirable and practical for most users. Nonetheless, due to the advancement in the computational tools, application of the dynamic models could be made simple and user-friendly.

Simultaneous passive sampling of hydrophilic and hydrophobic emerging organic contaminants in water

Passive sampling techniques have been considered robust tools for monitoring freely dissolved concentrations of contaminants in aquatic systems. However, few passive samplers are currently available for the simultaneous sampling of both hydrophilic and hydrophobic chemicals. In this study, we developed a novel passive sampler (a hydrophilic-lipophilic balance sorbent-embedded cellulose acetate membrane (HECAM)) for estimating the time-weighted average (TWA) concentrations of both hydrophilic and hydrophobic organic contaminants in water. In our laboratorial controlled dynamic experiments, the accumulation results of thirty-seven target chemicals (including organophosphorus flame retardants, phenols, estrogens, organophosphorus pesticides, and triazine herbicides) with a wide polarity range (1.44 < log K_ow < 9.49) in the HECAM followed first-order kinetics well, and the passive sampling parameters were estimated successfully. The estimated sampling rates for the target chemicals in the HECAM ranged from 0.14 to 6.90 L d^-1 in the laboratory experiment, and the log K_sw (equilibrium partition coefficient between the sampler and water) values ranged from 2.75 to 6.00. The HECAM exhibited high sampling rate for moderately hydrophilic and moderately hydrophobic chemicals. The field validation study in an urban river resulted in the detection of four target chemicals (tris(chloroisopropyl)phosphate, tris(1,3-dichloroisopropyl)phosphate, prometryn, and 4-tert-octylphenol) by the HECAM at estimated TWA concentrations of 10.9-179.5 ng L^-1, which were in agreement with the measured levels found in traditional grab samples by solid-phase extraction. In summary, both the laboratory tests and field deployment showed practicable results for the HECAM passive sampling, which suggests that it is an efficient approach for simultaneous monitoring of hydrophilic and hydrophobic organic contaminants in water.

Salinity and pH as factors affecting the passive sampling and extraction of pharmaceuticals from water

Passive sampling is an attractive technique for the long-term monitoring of pharmaceuticals in the water environment. The reliability of the received results depends on the properly performed calibration, namely the determination of analyte sampling rates. This step can be the source of a systematic error, as the sampling rate values are dependent on the water donor phase parameters. This is especially important for pharmaceuticals, since their chemical characteristics and ionic form change with pH. In this study, the cross-effect of pH (3, 7, and 9) and salinity (0, 7, and 35 practical salinity unit, using artificial sea water) on the passive sampling of 21 pharmaceuticals (antiparasitics, beta-blockers, non-steroidal anti-inflammatory drugs, sulfonamides) was tested. The primarily determined parameter was the sampling rate. In addition, the extraction efficiency, partitioning coefficient, and the concentration of the analytes on the sorbent were calculated. Generally, for the non-steroidal anti-inflammatory drugs, beta-blockers, and antiparasitics, the change both in pH and salinity had a negligible impact on the mentioned experimental parameters. In contrast, the extraction of sulfonamides was impacted by both pH and salinity, while lipophilicity was not a decisive parameter.