Occurrence, oral exposure and risk assessment of volatile organic compounds in drinking water for Izmir

Volatile organic compounds in water matrices: Recent progress, challenges, and perspective

Volatile organic compounds (VOCs) are a group of organic compounds that have a molecular structure containing carbon and their chemical properties allow them to be easily converted to steam and gas and remain for a long period of time and have diverse effects on the environment. The purpose of this study is determination of the concentration of VOCs such as alachlor, anthracene, benzene, bromoform, chloroform, heptachlor, isophorone, tetrachloroethylene, γ -chlordane, toluene, etc. in water matrices. The results showed that among studies conducted on VOCs, the concentration of tetrachloroethylene, m,p-xylene, and toluene were at the top in water matrices, and the lowest average concentrations were found in chloroform, anthracene, and butyl benzyl phthalate. In terms of VOC concentrations in water matrices, China was the most polluted country. Moreover, the data analysis indicated that China was the only country with carcinogenic risk. A Monte-Carlo simulation showed that although the averages obtained were comparable to the acceptable limits, for heptachlor, the maximum carcinogenic risk is achieved at a level that is slightly over the limit, only 25% from the population being exposed.

Assessing the Persistence and Mobility of Organic Substances to Protect Freshwater Resources

Persistent and mobile organic substances are those with the highest propensity to be widely distributed in groundwater and thereby, when emitted at low-levels, to contaminate drinking water extraction points and freshwater environments. To prevent such contamination, the European Commission is in the process of introducing new hazard classes for persistent, mobile, and toxic (PMT) and very persistent and very mobile (vPvM) substances within its key chemical regulations CLP and REACH. The assessment of persistence in these regulations will likely be based on simulated half-life, t _1/2, thresholds; the assessment of mobility will likely be based on organic carbon-water distribution coefficient, K _OC, thresholds. This study reviews the use of t _1/2 and K _OC to describe persistence and mobility, considering the theory, history, suitability, data limitations, estimation methods, and alternative parameters. For this purpose, t _1/2, K _OC, and alternative parameters were compiled for substances registered under REACH, known transformation products, and substances detected in wastewater treatment plant effluent, surface water, bank filtrate, groundwater, raw water, and drinking water. Experimental t _1/2 values were rare and only available for 2.2% of the 14 203 unique chemicals identified. K _OC data were only available for a fifth of the substances. Therefore, the usage of alternative screening parameters was investigated to predict t _1/2 and K _OC values, to assist weight-of-evidence based PMT/vPvM hazard assessments. Even when considering screening parameters, for 41% of substances, PMT/vPvM assessments could not be made due to data gaps; for 23% of substances, PMT/vPvM assessments were ambiguous. Further effort is needed to close these substantial data gaps. However, when data is available, the use of t _1/2 and K _OC is considered fit-for-purpose for defining PMT/vPvM thresholds. Using currently discussed threshold values, between 1.9 and 2.6% of REACH registered substances were identified as PMT/vPvM. Among the REACH registered substances detected in drinking water sources, 24-30% were PMT/vPvM substances.

Probabilistic human health-risk assessment and influencing factors of aromatic hydrocarbon in groundwater near urban industrial complexes in Northeast China

Organic pollutants are common in the environment, very difficult to remove, and pose a serious threat to human health. Probabilistic risk assessment advances conservative single-point estimation and brings a new perspective to risk assessment. From 2009 to 2019, we monitored the distribution of major pollutants in an industrial park in Northeastern China. The result showed the maximum concentration of benzene reached 73,680 μg/L in 2009, benzo[a]pyrene reached 36.80 ng/L in 2016. These concentrations are significantly above the levels set by Chinese regulatory agencies. The single-factor index increases year by year, and pollutants gradually spread from the pollution leakage source to surrounding areas. A new method was used to quantify the human health risk from groundwater organic pollution accurately, based on the triangular fuzzy numbers coupled with the Monte Carlo simulation. The Monte Carlo simulation was used to simulate the triangular fuzzy numbers. This simplified the operation between the triangular fuzzy numbers and their function successfully and obtained the risk as a set of values. The results indicated that non-carcinogenic risk was negligible in all age groups (children, adolescents, and adults). Conversely, when it comes to carcinogenic risks, adults were about 50-270 times the tolerable level of risk due to long exposure years and wide skin contact areas. Oral ingestion played an essential role in total exposure (>90%) compared to dermal contact. Control of exposure duration and intake should be prioritized when making decisions to reduce risk uncertainty. Monte Carlo simulation-triangular fuzzy numbers can effectively reduce the risk of uncertainty and reflect the complex conditions of the groundwater environment for small amounts of data or inaccurate data.

Characteristics and health risks of benzene series and halocarbons near a typical chemical industrial park

Health risks of typical benzene series and halocarbons (BSHs) in a densely populated area near a large-scale chemical industrial park were investigated. Ambient and indoor air and tap water samples were collected in summer and winter; and the concentration characteristics, sources, and exposure risks of typical BSH species, including five benzene series (benzene, toluene, ethylbenzene, o-xylene, m,p-xylene) and five halocarbons (dichloromethane, trichloromethane, trichloroethylene, tetrachloromethane, and tetrachloroethylene), were analysed. The total mean concentrations of BSHs were 53.32 μg m^-3, 36.29 μg m^-3, and 26.88 μg L^-1 in indoor air, ambient air, and tap water, respectively. Halocarbons dominated the total BSHs with concentrations relatively higher than those in many other industrial areas. Industrial solvent use, industrial processes, and vehicle exhaust emissions were the principal sources of BSHs in ambient air. The use of household products (e.g., detergents and pesticides) was the principal source of indoor BSHs. Inhalation is the primary human exposure route. Ingestion of drinking water was also an important exposure route but had less impact than inhalation. Lifetime non-cancer risks of individual and cumulative BSHs were below the threshold (HQ = 1), indicating no significant lifetime non-cancer risks in the study area. However, tetrachloromethane, benzene, trichloromethane, ethylbenzene, and trichloroethylene showed potential lifetime cancer risk. The cumulative lifetime cancer risks exceeded the tolerable benchmark (1 × 10^-4), indicating a lifetime cancer risk of BSHs to residents near the chemical industry park. This study provides valuable information for the management of public health in chemical industrial parks.

Occurrence, Potential Sources, and Risk Assessment of Volatile Organic Compounds in the Han River Basin, South Korea

Increasing public awareness about the aesthetics and safety of water sources has shifted researchers’ attention to the adverse effects of volatile organic compounds (VOCs) on humans and aquatic organisms. A total of 17 VOCs, including 10 volatile halogenated hydrocarbons and seven volatile non-halogenated hydrocarbons, were investigated at 36 sites of the Han River Basin, which is the largest and most important drinking water source for residents of the Seoul metropolitan area and Gyeonggi province in South Korea. The VOC concentrations ranged from below detection limits to 1.813 µg L⁻¹. The most frequently detected VOC was 1,2-dichloropropane, with a detection frequency of 80.56%, as it is used as a soil fumigant, chemical intermediate, and industrial solvent. In terms of geographical trends, the sampling sites that were under the influence of sewage and industrial wastewater treatment plants were more polluted with VOCs than other areas. This observation was also supported by the results of the principal component analysis. In the present study, the detected concentrations of VOCs were much lower than that of the predicted no-effect concentrations, suggesting low ecological risk in the Han River. However, a lack of available ecotoxicity data and limited comparable studies warrants further studies on these compounds.

Fine and coarse particulate matter, trace element content, and associated health risks considering respiratory deposition for Ergene Basin, Thrace

Ergene Basin is located in Thrace, Turkey, where industries are densely populated. This study aimed to determine exposure of people living in Ergene Basin (Çorlu and Çerkezköy) to fine and coarse PM, and its potentially toxic element (PTE) content by considering variation in respiratory airway deposition rates with daily activities and PM particle size by employing deposition models of International Commission on Radiological Protection and Multiple Path Particle Dosimetry. Fine and coarse PM samples were collected daily for a year at points in Çorlu and Çerkezköy representing urban and industrial settings, respectively. A questionnaire survey was conducted in the study area to obtain time-activity budgets, and associated variation was included in the health risk assessment by considering time-activity-dependent inhalation rates. The studied PTEs were Al, As, Ba, Cd, Cr, Co, Mn, Ni, Pb, and Se. The mean fine and coarse PM concentrations were measured as 23 and 14 μg/m³ in Çorlu, and 22 and 12 μg/m³ in Çerkezköy, respectively. The only PTE that exceeded acceptable risk in terms of total carcinogenic risk was Cr. Non-carcinogenic risks of all the PTEs including Cr were below the threshold. The use of deposition fractions in the health risk assessment (HRA) calculations was found to prevent overestimation of health risks by at least 91% and 87% for fine and coarse PM, respectively, compared to the regular HRA. Minor differences in risk between Çorlu and Çerkezköy suggest that urban pollution sources could be at least as influential on human health as industrial sources.

Human health risk assessment for exposure to BTEXN in an urban aquifer using deterministic and probabilistic methods: A case study of Chennai city, India

The aquifer in Tondiarpet, Chennai, had been severely contaminated with petroleum fuels due to an underground pipeline leakage. Groundwater samples were analyzed quarterly for priority pollutants such as benzene, toluene, ethylbenzene, xylenes, and naphthalene (BTEXN) using purge and trap gas chromatography and mass spectrometer from 2016 to 2018. The maximum concentrations of BTEXN in groundwater at the site were found to be greater than the permissible limits significantly. Among the five sampling locations (MW1, MW2, MW3, MW4, and MW5), mean BTEXN levels were found to be higher near MW2, confirming the source location of petroleum leakage. Human health risk assessment was carried out using deterministic and probabilistic methods for exposure to BTEXN by oral and dermal exposure pathways. Risk analysis indicated that mean cancer and non-cancer risks were many times higher than the allowable limits of 1E-06 and 1 respectively in all age groups (children, teens, and adults), implying the adverse health effects. Oral exposure is predominately contributing (60-80%) to the total health risk in comparison to the dermal exposure route. Variability and uncertainty were addressed using the Monte Carlo simulations and the resultant minimum, maximum, 5th, 95th^, and mean percentile risks were predicted. Under the random exposure conditions to BTEXN, it was estimated that the risk would become unacceptable for >98.7% of the exposed population. Based on the sensitivity analysis, exposure duration, and ingestion rate are the crucial variables contributing significantly to the health risk. As part of the risk management, preliminary remediation goals for the study site were estimated, which require >99% removal of the BTEXN contamination for risk-free exposures. It is suggested that the residents of Tondiarpet shouldn't utilize the contaminated groundwater mainly for oral ingestion to lower the cancer incidence related to exposure to BTEXN.

Non-targeted screening and analysis of volatile organic compounds in drinking water by DLLME with GC-MS

Volatile organic compounds (VOCs) in drinking water may potentially be hazardous. We developed a novel non-targeted analysis method of VOCs in drinking water that uses dispersive liquid-liquid microextraction coupled with gas chromatography-mass spectrometry. Analysis parameters were selected from range-finding tests on the peak number and average area of the extracted compounds. The optimized method was applied to analyze VOCs in tap water samples collected from Wuhan City, China. Twenty-seven compounds with high match degrees and a high prevalence were selected for quantification and evaluation. We used structure-activity relationships to predict the carcinogenicity of these compounds. Although most of the compounds were non-toxic, compounds such as dibutyl phthalate and diacetone alcohol should be investigated further. Untargeted analysis of the tap water samples identified 75-200 VOCs, including 67 highly prevalent compounds. Industrial and pharmaceutical chemicals accounted for approximately 70% of the VOCs in the samples. This method of non-targeted analysis and in silico toxicity prediction is simple and economic, and could be used in screening VOCs in drinking water.

Toward the Required Detection Limits for Volatile Organic Constituents in Marine Environments with Infrared Evanescent Field Chemical Sensors

A portable sensor system for the simultaneous detection of multiple environmentally relevant volatile organic compounds (VOCs) in real seawater based on Fourier transform infrared fiber-optic evanescent wave spectroscopy (FT-IR-FEWS) was developed. A cylindrical silver halide (AgX) fiber with an ethylene/propylene copolymer (E/P-co) coated flattened segment was used as an active optical transducer. The polymer membrane enriches the hydrophobic analytes, while water is effectively excluded from the penetration depth of the evanescent field. Determination of multicomponent mixtures (i.e., 10 VOCs in real-world seawater samples) collected in Arcachon Bay, France revealed a high accuracy and reproducibility with detection limits down to 560 ppb. The measurement showed no significant influence from changing water conditions (e.g., salinity, turbidity, and temperature or other interfering substances). The time constants for 90% saturation of the polymer ranged from 20 to 60 min. The sensor system is capable of being transported for on-site monitoring of environmental pollutants in aqueous matrices with efficient long-term stability, thus showing great potential to be utilized as an early warning system.

Sorptive removal of toluene and m-xylene by municipal solid waste biochar: Simultaneous municipal solid waste management and remediation of volatile organic compounds

The remediation of volatile organic compounds (VOCs) from aqueous solution using Municipal solid waste biochar (MSW-BC) has been evaluated. Municipal solid waste was pyrolyzed in an onsite pyrolyzer around 450 ^°C with a holding time of 30 min for the production of biochar (BC). Physiochemical properties of BC were assessed based on X-Ray Fluorescence (XRF) and Fourier transform infra-red (FTIR) analysis. Adsorption capacities for the VOCs (m-xylene and toluene) were examined by batch sorption experiments. Analysis indicated high loading of m-xylene and toluene in landfill leachates from different dump sites. The FTIR analysis corroborates with the Boehm titration data whereas XRF data demonstrated negligible amounts of trace metals in MSW-BC to be a potential sorbent. Adsorption isotherm exhibited properties of both Langmuir and Freundlich which is indicative of a non-ideal monolayer adsorption process taking place. Langmuir adsorption capacities were high as 850 and 550 μg/g for toluene and m-xylene respectively. The conversion of MSW to a value added product provided a feasible means of solid waste management. The produced MSW-BC was an economical adsorbent which demonstrated a strong ability for removing VOCs. Hence, MSW-BC can be used as a landfill cover or a permeable reactive barrier material to treat MSW leachate. Thus, the conversion of MSW to BC becomes an environmentally friendly and economical means of solid waste remediation.

Multi-route - Multi-pathway exposure to trihalomethanes and associated cumulative health risks with response and dose addition

Cumulative health risk estimation for exposure to mixtures is a current issue, which would present a useful tool for environmental and public health management. Cumulative risks were estimated with response and dose addition methods for individual multi-route - multi-pathway exposure to trihalomethanes and associated carcinogenic toxic risks in Izmir, Turkey. Exposure levels were estimated for ingestion, dermal, and inhalation routes using measured tap water and bottled water THM concentrations. Drinking, showering, hand and dish washing were the considered pathways. THM concentrations in air during the showering were modeled with two-resistance theory using tap water concentration data. The estimated carcinogenic risk levels for ingestion route were in the range of safe (<10^-6) to low priority (<10^-4), for dermal route all were in the safe zone (<10^-6), and for inhalation route were in the range of safe to high priority (>10^-4) zones, indicating ingestion and inhalation routes were of similar significance ahead of dermal exposure. Cumulative carcinogenic risks of THM compounds were estimated using simple (response) addition and dose addition using cumulative relative potency factor (CRPF) methods. CRPF method estimated the risks at lower levels compared to the simple addition, which originated from the use two different risk factor values for the index chemical in the method. Cumulative chronic-toxic risks were also assessed, rendering below the threshold risk levels for all routes. This study showed that multi-route - multi-pathway exposure assessment and cumulative risk assessment should together be considered for better environmental and public health management.

Source apportionment and carcinogenic risk assessment of passive air sampler-derived PAHs and PCBs in a heavily industrialized region

Cancer has become the primary reason of deaths in Dilovasi probably due to its location with unique topography under the influence of heavy industrialization and traffic. In this study, possible sources and carcinogenic health risks of PAHs and PCBs were investigated in Dilovasi region by Positive Matrix Factorization (PMF) and the USEPA approach, respectively. PAHs and PCBs were measured monthly for a whole year at 23 sampling sites using PUF disk passive samplers. Average ambient air concentrations were found as 285±431ng/m³ and 4152±6072pg/m³, for Σ₁₅PAH and Σ₄₁PCB, respectively. PAH concentrations increased with decreasing temperature especially at urban sites, indicating the impact of residential heating in addition to industrial activities and traffic. On the other hand, PCB concentrations mostly increased with temperature probably due to enhanced volatilization from their sources. Possible sources of PAHs were found as emissions of diesel and gasoline vehicles, biomass and coal combustion, iron and steel industry, and unburned petroleum/petroleum products, whereas iron-steel production, coal and biomass burning, technical PCB mixtures, and industrial emissions were identified for PCBs. The mean carcinogenic risk associated with inhalation exposure to PAHs and PCBs were estimated to be >10^-6 and >10^-5, respectively, at all sampling points, while the 95th percentile was >10^-5 at 15 of 23 and >10^-4 at 8 of 23 sampling locations, respectively. Probabilistic assessment showed, especially for PCBs, that a majority of Dilovasi population face significant health risks. The higher risks due to PCBs further indicated that PCBs and possibly other pollutants originating from the same sources such as PBDEs and PCNs may be an important issue for the region.

Spatial and seasonal variations, sources, air-soil exchange, and carcinogenic risk assessment for PAHs and PCBs in air and soil of Kutahya, Turkey, the province of thermal power plants

Atmospheric and concurrent soil samples were collected during winter and summer of 2014 at 41 sites in Kutahya, Turkey to investigate spatial and seasonal variations, sources, air-soil exchange, and associated carcinogenic risks of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs). The highest atmospheric and soil concentrations were observed near power plants and residential areas, and the wintertime concentrations were generally higher than ones measured in summer. Spatial distribution of measured ambient concentrations and results of the factor analysis showed that the major contributing PAH sources in Kutahya region were the coal combustion for power generation and residential heating (48.9%), and diesel and gasoline exhaust emissions (47.3%) while the major PCB sources were the coal (thermal power plants and residential heating) and wood combustion (residential heating) (45.4%), and evaporative emissions from previously used technical PCB mixtures (34.7%). Results of fugacity fraction calculations indicated that the soil and atmosphere were not in equilibrium for most of the PAHs (88.0% in winter, 87.4% in summer) and PCBs (76.8% in winter, 83.8% in summer). For PAHs, deposition to the soil was the dominant mechanism in winter while in summer volatilization was equally important. For PCBs, volatilization dominated in summer while deposition was higher in winter. Cancer risks associated with inhalation and accidental soil ingestion of soil were also estimated. Generally, the estimated carcinogenic risks were below the acceptable risk level of 10^-6. The percentage of the population exceeding the acceptable risk level ranged from <1% to 16%, except, 32% of the inhalation risk levels due to PAH exposure in winter at urban/industrial sites were >10^-6.

POPs in a major conurbation in Turkey: ambient air concentrations, seasonal variation, inhalation and dermal exposure, and associated carcinogenic risks

Semi-volatile organic compounds were monitored over a whole year, by collection of gas and particle phases every sixth day at a suburban site in Izmir, Turkey. Annual mean concentrations of 32 polychlorinated biphenyls (∑₃₂PCBs) and 14 polycyclic aromatic hydrocarbons (∑₁₄PAHs) were 348 pg/m³ and 36 ng/m³, respectively, while it was 273 pg/m³ for endosulfan, the dominant compound among 23 organochlorine pesticides (OCPs). Monte Carlo simulation was applied to the USEPA exposure-risk models for the estimation of the population exposure and carcinogenic risk probability distributions for heating and non-heating periods. The estimated population risks associated with dermal contact and inhalation routes to ∑₃₂PCBs, ∑₁₄PAHs, and some of the targeted OCPs (α-hexachlorocyclohexane (α-HCH), β-hexachlorocyclohexane (β-HCH), heptachlor, heptachlor epoxide, α-chlordane (α-CHL), γ-chlordane (γ-CHL), and p,p'-dichlorodiphenyltrichloroethane (p,p'-DDT)) were in the ranges of 1.86 × 10^-16-7.29 × 10^-9 and 1.38 × 10^-10-4.07 × 10^-6, respectively. The inhalation 95th percentile risks for ∑₃₂PCBs, ∑₁₄PAHs, and OCPs were about 6, 3, and 4-7 orders of magnitude higher than those of dermal route, respectively. The 95th percentile inhalation risk for ∑₃₂PCBs and OCPs in the non-heating period were 1.8- and 1.2-4.6 folds higher than in the heating period, respectively. In contrast, the 95th percentile risk levels for ∑₁₄PAHs in the heating period were 4.3 times greater than that of non-heating period for inhalation, respectively. While risk levels associated with exposure to PCBs and OCPs did not exceed the acceptable level of 1 × 10^-6, it was exceeded for 47 % of the population associated with inhalation of PAHs with a maximum value of about 4 × 10^-6.

Quality of Kelantan drinking water and knowledge, attitude and practice among the population of Pasir Mas, Malaysia

OBJECTIVES

Information about the quality of drinking water, together with analysis of knowledge, attitude and practice (KAP) analysis and health risk assessment (HRA) remain limited. The aims of this study were: (1) to ascertain the level of KAP regarding heavy metal contamination of drinking water in Pasir Mas; (2) to determine the concentration of heavy metals (Al, Cr, Cu, Fe, Ni, Pb, Zn and Cd) in drinking water in Pasir Mas; and (3) to estimate the health risks (non-carcinogenic and carcinogenic) caused by heavy metal exposure through drinking water using hazard quotient and lifetime cancer risk.

METHODS

Information on KAP was collected using a standardized questionnaire. Heavy metal analysis of drinking water samples was performed using graphite furnace atomic absorption spectrophotometry.

RESULTS

The population of Pasir Mas has good knowledge (80%), a less positive attitude (93%) and good practice (81%) towards heavy metal contamination of drinking water. The concentrations of heavy metals analysed in this study were found to be below the permissible limits for drinking water set by the Malaysian Ministry of Health and the World Health Organization. The HRA showed no potential non-carcinogenic and carcinogenic risks from the intake of heavy metal through drinking water.

CONCLUSION

By investigating the quality of drinking water, KAP and HRA, the results of this study will provide authorities with the knowledge and resources to improve the management of drinking water quality in the future.

Polycyclic Aromatic Hydrocarbons Concentrations in Drinking Water in Villages along the Huai River in China and Their Association with High Cancer Incidence in Local Population

This study aims to evaluate the carcinogenic risk of PAHs in the drinking water of counties along the Huai River in China and study their associations with high cancer incidence in local population. We investigated 20 villages with high cancer incidence rates as the risk group and 20 villages with low rates as the control group. Water samples from each village were collected in the winter and summer seasons to analyze the concentrations of 16 PAHs. The carcinogenic risks of the PAHs were calculated for each village using a health risk assessment approach. Results showed that PAHs concentrations in 27.2% of the water samples were higher than the allowable values in China. However, no significant difference in water PAHs concentrations was observed between the risk and control groups (P > 0.05), and no correlation was found between water PAHs concentrations and cancer incidence in these villages. The average upper bound carcinogenic risks were less than 1 × 10⁻⁴ in both groups. In conclusion, PAHs were present in the drinking water of the studied villages, but their carcinogenic risks remained within acceptable limits. PAHs in local drinking water might not be the major environmental cause of the high cancer incidences.

Assessing the human health impacts of exposure to disinfection by-products--a critical review of concepts and methods

Understanding the public health implications of chemical contamination of drinking water is important for societies and their decision-makers. The possible population health impacts associated with exposure to disinfection by-products (DBPs) are of particular interest due to their potential carcinogenicity and their widespread occurrence as a result of treatments employed to control waterborne infectious disease. We searched the literature for studies that have attempted quantitatively to assess population health impacts and health risks associated with exposure to DBPs in drinking water. We summarised and evaluated these assessments in terms of their objectives, methods, treatment of uncertainties, and interpretation and communication of results. In total we identified 40 studies matching our search criteria. The vast majority of studies presented estimates of generic cancer and non-cancer risks based on toxicological data and methods that were designed with regulatory, health-protective purposes in mind, and therefore presented imprecise and biased estimates of health impacts. Many studies insufficiently addressed the numerous challenges to DBP risk assessment, failing to evaluate the evidence for a causal relationship, not appropriately addressing the complex nature of DBP occurrence as a mixture of chemicals, not adequately characterising exposure in space and time, not defining specific health outcomes, not accounting for characteristics of target populations, and not balancing potential risks of DBPs against the health benefits related with drinking water disinfection. Uncertainties were often poorly explained or insufficiently accounted for, and important limitations of data and methods frequently not discussed. Grave conceptual and methodological limitations in study design, as well as erroneous use of available dose-response data, seriously impede the extent to which many of these assessments contribute to understanding the public health implications of exposure to DBPs. In some cases, assessment results may cause unwarranted alarm among the public and potentially lead to poor decisions being made in sourcing, treatment, and provision of drinking water. We recommend that the assessment of public health impacts of DBPs should be viewed as a means of answering real world policy questions relating to drinking water quality, including microbial contaminants; that they should be conducted using the most appropriate and up-to-date data and methods, and that associated uncertainties and limitations should be accounted for using quantitative methods where appropriate.

Benzene homologues in environmental matrixes from a pesticide chemical region in China: Occurrence, health risk and management

The contamination status and health risks of benzene, toluene, ethylbenzene and xylene (BTEX) in air, soil, dust and groundwater were evaluated in a pesticide chemical region located in Hebei province, China. The concentrations of BTEX in air ranged from 7.80 to 238ug/m(3) and those in soil and dust ranged from lower than limit of detection (LOD) to 32,360ng/g dw, and those in groundwater varied from 2.68 to 98.6ug/L. Generally, the levels of BTEX in multimedia matrixes were all below the standards established in China. Health risk assessment was performed based on the monitoring data via inhalation, dermal contact and ingestion pathways and hazard quotient (HQ) was calculated to be on the order of 10(-7), below 10(-6), and Hazard index (HI) levels of BTEX were lower than 1.0. However, both HQ and HI ascended with an increase in work experience/exposure. Integrated risk management was proposed to eliminate BTEX pollution and to protect occupational health of workers in those industries.

Formation of organochlorine by-products in bleached laundry

Laundering fabrics with chlorine bleach plays a role in health and hygiene as well as aesthetics. However, laundry bleaching may create chlorinated by-products with potentially adverse human health effects. Studies have shown that toxic chlorinated gases are produced in the headspace of washing machines when hypochlorite-containing bleach is used. Laundry bleaching has also been implicated in contributing dissolved organochlorine to municipal wastewater. However, there have been no reports of organochlorines produced and retained in fabric as a result of laundry bleaching. We have used a chlorine-specific X-ray spectroscopic analysis to demonstrate the formation of organochlorine by-products in cotton fabrics laundered with chlorine bleach under typical household conditions. Organochlorine formation increases at higher wash temperature. At least two pools of organochlorine are produced in bleached fabric: a labile fraction that diminishes over several months of storage time as well as a more stable fraction that persists after more than 1 year. Our results also suggest that residual hypochlorite remains in fabric after laundering with bleach, presenting the possibility of direct and sustained dermal contact with reactive chlorine. This study provides a first step toward identifying a new risk factor for elevated organochlorine body burdens in humans.

Occurrence and Assessment of Chemical Contaminants in Drinking Water in Tunceli, Turkey

The objective of this study was to analyze drinking water samples from 21 sites in the city center and seven municipalities of Tunceli, Turkey, in order to determine the presence of nitrate, nitrite, fluoride, bromate, pesticides, polycyclic aromatic hydrocarbons (PAHs), trihalomethanes (THMs), and some other chemicals. In all locations, the concentrations of chemicals investigated were below the permissible limits set by local and international organizations for drinking water. Low levels of nitrate (4.79 ± 4.20 mg/L), fluoride (0.11 ± 0.08 mg/L), and THMs (6.63 ± 5.14 μg/L) were detected in all locations. A low level of tetra, chloroethane, which is suspected to be a human carcinogen, was also detected in 8 locations in the range of 0.26–0.43 μg/L. These contaminants may pose adverse health effects or minimum hazard due to long-term exposure. In all locations, bromate, benzene, total PAH, 1-2 dichloroethane, vinyl chloride, acrylamide, and epichloridine levels in drinking water samples were under detection limits.

Risk assessment of exposure to lead in tap water among residents of Seri Kembangan, Selangor state, Malaysia

Introduction:

A cross sectional study was conducted to estimate risk of exposure to lead via tap water ingestion pathway for the population of Seri Kembangan (SK).

Methodology:

By using purposive sampling method, 100 respondents who fulfilled the inclusive criteria were selected from different housing areas of SK based on geographical population distribution. Residents with filtration systems installed were excluded from the study. Questionnaires were administered to determine water consumption-related information and demographics. Two water samples (first-flushed and fully-flushed samples) were collected from kitchen tap of each household using HDPE bottles. A total of 200 water samples were collected and lead concentrations were determined using a Graphite Furnace Atomic Absorption Spectrophotometer (GFAAS).

Results:

Mean lead concentration in first-flushed samples was 3.041± SD 6.967µg/L and 1.064± SD 1.103µg/L for fully-flushed samples. Of the first-flushed samples, four (4) had exceeded the National Drinking Water Quality Standard (NDWQS) lead limit value of 10µg/L while none of the fully-flushed samples had lead concentration exceeded the limit. There was a significant difference between first-flushed samples and fully-flushed samples and flushing had elicited a significant change in lead concentration in the water (Z = -5.880, p<0.05). It was also found that lead concentration in both first-flushed and fully flushed samples was not significantly different across nine (9) areas of Seri Kembangan (p>0.05). Serdang Jaya was found to have the highest lead concentration in first-flushed water (mean= 10.44± SD 17.83µg/L) while Taman Universiti Indah had the highest lead concentration in fully-flushed water (mean=1.45± SD 1.83µg/L). Exposure assessment found that the mean chronic daily intake (CDI) was 0.028± SD 0.034µgday^-1kg^-1. None of the hazard quotient (HQ) value was found to be greater than 1.

Conclusion:

The overall quality of water supply in SK was satisfactory because most of the parameters tested in this study were within the range of permissible limit and only a few samples had exceeded the standard values for lead and pH. Non-carcinogenic risk attributed to ingestion of lead in SK tap water was found to be negligible.

Evaluation of neuropsychological symptoms and exposure to benzene, toluene and xylene among two different furniture worker groups in Izmir

This study was conducted to determine whether there was any exposure to toluene, xylene and benzene and to assess the health impact of these solvents on workers in furniture enterprises in Karabaglar, Izmir. This cross-sectional study covered furniture enterprises in Karabaglar, Izmir. This study was comprised of an exposed group consisting of workers engaged in painting and varnishing and therefore exposed either directly or indirectly toluene, xylene and benzene in the workplace and the non-exposed group engaged in other aspects of production. While a total of 261 individuals completed questionnaires, 210 workers agreed to provide blood samples. Blood solvents levels were determined using gas chromatograph at Ege University, Intoxication Research and Application Centre. The modified EUROQUEST questionnaire was used to assess neuropsychological symptoms and neurological and general examination were performed. Occupational and exposure history, demographic and work-related information was collected. In this study of workers, blood toluene and benzene levels were found to be significantly higher among those engaged in painting and varnishing compared to those who perform other tasks. The average blood toluene and benzene concentrations among exposed workers were 6.95 times and 1.64 times respectively higher than those in the nonexposed groups. Smokers and participants who worked in excess of 8 hours/day had higher blood toluene and benzene levels. The most frequently work-related health complaints were back pain, allergies and asthma. No differences were found in the average scores in the neuropsychological symptoms questionnaire between exposed and non-exposed groups. Neurological examination of two individuals with these complaints revealed a loss of reflexes. The workers were unaware that they were being exposed to solvents at work. Tobacco smoke is a major source of internal exposure to benzene. Improving working conditions in furniture work places is a priority.

Spatial variations of human health risk associated with exposure to chlorination by-products occurring in drinking water

During disinfection, chlorine reacts with organic matter present in drinking water and forms various undesirable chlorinated by-products (CBPs). This paper describes a study of the spatial variability of human health risk (i.e., cancer effects) from CBP exposure through drinking water in a specific region. The region under study involves nine drinking water distribution systems divided into several zones based on their characteristics. The spatial distribution of cancer risk (CR) was estimated using two years of data (2006-2008) on various CBP species. In this analysis, trihalomethanes (THMs) and haloacetic acids (HAAs) served as surrogates for CBPs. Three possible routes of exposure (i.e., via ingestion, inhalation and dermal contact) were considered for each selected compound. The cancer risk assessment involved estimating a unit risk (R(T)) in each zone of the selected distribution systems. A probabilistic analysis based on Monte Carlo simulations was employed. Risk assessment results showed that cancer risk varied between systems, but also within individual systems. As a result, the population of the same region was not exposed to the same risk associated with CBPs in drinking water. Unacceptable levels (i.e., R(T) > 10(-4)) for the estimated CR were determined for several zones in the studied region. This study demonstrates that a spatial-based analysis performed to represent the spatial distribution of risk estimates can be helpful in identifying suitable risk management strategies. Suggestions for improving the risk analysis procedure are also presented.

Investigation and assessment of volatile organic compounds in water sources in China

456 water samples collected from 152 water sources in 2006 were analyzed for 21 volatile organic compounds (VOCs). Concentrations of 21 VOCs ranged from below method detection limits of the laboratory to 7.65 μg/L (toluene), but seldom exceeded the concentration limits set in the National Drinking Water Quality Standards (GB5749-2006) or the National Environmental Quality Standards for Surface Water (GB3838-2002) of China. Of the 21 individual VOCs analyzed, 11 VOCs were detected in at least one sample at or above 1.0 μg/L; 6.6% of the water samples had a detection of at least one VOC at or above 1.0 μg/L, and 2.6% had a detection of at least two VOCs at or above 1.0 μg/L. Based on the statistical data of detection frequencies above the method detection limits, 75% of the samples detected at least one VOC, and 65% of the samples detected at least two VOCs. Chloroform, toluene, and 1,2-dichloroethene were the three most frequently detected VOCs, with detection frequencies of 76.97%, 68.42%, and 44.08%, respectively. Volatile halogenated hydrocarbons and gasoline components were the two most frequently detected VOC groups.

An assessment of indoor air concentrations and health risks of volatile organic compounds in three primary schools

Concentrations of volatile organic compounds (VOCs), including formaldehyde, in classrooms, kindergartens, and outdoor playgrounds of three primary schools were measured in spring, winter, and fall terms in İzmir, Turkey. A health-risk assessment was conducted for odor detection, sensory irritation, chronic toxic effects, and cancer. Active sampling was applied for VOCs and formaldehyde on Tenax TA and DNPH tubes, respectively. VOCs were analyzed in a thermal desorption-GC-MS system. Formaldehyde analysis was performed using an HPLC instrument. Benzene, toluene, and formaldehyde were the most abundant compounds with 95th percentile indoor air concentrations of 29, 87, and 106 μg/m(3), respectively. Naphthalene and xylenes followed them with an order of magnitude lower concentrations. Two isomers of dichlorobenzene (1,3 and 1,4) were the other notable compounds. The concentrations were utilized to classify the indoor air pollutants with respect to potential health effects. In addition, carcinogenic and chronic toxic risks were estimated using Monte-Carlo simulation. Formaldehyde appears to be the most concerning pollutant with high chronic toxic and carcinogenic risk levels according to the health assessment followed by naphthalene, benzene, and toluene due to their chronic effects.

A survey of organic contaminants in household and bottled drinking waters in Kuwait

Chemical analysis of volatile organic compounds (VOCs) and semivolatiles (SVs), including pesticides, was performed on 623 and 568 samples, respectively, of household drinking water, as well as on 113 samples from 71 brands of bottled water available in Kuwaiti markets. The analysis was performed according to United States Environmental Protection Agency (US-EPA) Methods 524.2 and 525.2. Nine VOCs and eight SVs were found in household water. Furthermore, between one and seven of 12 VOCs were detected in 93% of the bottled water brands. All bottled waters were found to be completely free of SVs. Styrene was the main pollutant found in all brands packaged in polystyrene containers of sizes 200-mL and 250-mL, with levels generally higher than the WHO guideline value of 20 microg/L. The levels of styrene, toluene, ethyl benzene and xylenes were found to increase with storage time, which indicates that these VOCs were migrating from the container material. No effect was detected due to changes in the storage temperature. All detected VOCs and SVs in household and bottled waters, except styrene, were found at concentrations much lower than those established as safe by WHO guidelines and US-EPA maximum contaminant levels (MCLs), respectively.

A health risk assessment for exposure to trace metals via drinking water ingestion pathway

A health risk assessment was conducted for exposure to trace metals via drinking water ingestion pathway for Province of Izmir, Turkey. Concentrations of 11 trace metals were measured in drinking waters collected from 100 population weighted random sampling units (houses). The samples were analyzed in atomic absorption spectrometry for arsenic, and inductively coupled plasma-optical emission spectrometry for Be, Cd, Co, Cr, Cu, Mn, Ni, Pb, V, and Zn. Questionnaires were administered to a participant from each sampling unit to determine drinking water consumption related information and demographics. Exposure and risks were estimated for each individual by direct calculation, and for Izmir population by Monte Carlo simulation. Six trace metals (As, Cr, Cu, Mn, Ni, and Zn) were detected in >50% of the samples. Concentrations of As and Ni exceeded the corresponding standards in 20% and 58% of the samples, respectively. As a result, arsenic noncarcinogenic risks were higher than the level of concern for 19% of the population, whereas carcinogenic risks were >10(-4) for 46%, and >10(-6) for 90% of the population.

Halogenated volatile organic compounds from the use of chlorine-bleach-containing household products

Sodium hypochlorite (NaOCl) and many organic chemicals contained in household cleaning products may react to generate halogenated volatile organic compounds (VOCs). Halogenated VOC emissions from eight different chlorine bleach containing household products (pure and diluted) were investigated by headspace experiments. Chloroform and carbon tetrachloride were the leading compounds along with several halogenated compounds in the headspace of chlorine bleach products. One of the most surprising results was the presence of carbon tetrachloride (a probable human carcinogen and a powerful greenhouse gas that was banned for household use by the U.S. Food and Drug Administration) in very high concentrations (up to 101 mg m(-3)). By mixing surfactants or soap with NaOCl, it was shown that the formation of carbon tetrachloride and several other halogenated VOCs is possible. In addition to quantitatively determined halogenated VOCs (n = 15), several nitrogen-containing (n = 4), chlorinated (n = 10), oxygenated compounds (n = 22), and hydrocarbons (n = 14) were identified in the headspace of bleach products. Among these, 1,1-dichlorobutane and 2-chloro-2-nitropropane were the most abundant chlorinated VOCs, whereas trichloronitromethane and hexachloroethane were the most frequently detected ones. Indoor air halogenated VOC concentrations resulting from the use of four selected household products were also measured before, during, and 30 min after bathroom, kitchen, and floor cleaning applications. Chloroform (2.9-24.6 microg m(-3)) and carbon tetrachloride (0.25-459 microg m(-3)) concentrations significantly increased during the use of bleach containing products. During/ before concentration ratios ranged between 8 and 52 (25 +/- 14, average +/- SD) for chloroform and 1-1170 (146 +/- 367, average +/- SD) for carbon tetrachloride, respectively. These results indicated that the bleach use can be important in terms of inhalation exposure to carbon tetrachloride, chloroform and several other halogenated VOCs.