Photocatalytic ozonation of urban wastewater and surface water using immobilized TiO2 with LEDs: Micropollutants, antibiotic resistance genes and estrogenic activity

Removal of ceftriaxone and cefotaxime antibiotics from industrial wastewater via complexation with Cu(II)

A high-performance liquid chromatographic method (HPLC) with UV detection is described for determination of ceftriaxone sodium (CFX) and cefotaxime sodium (CFM) content in pharmaceutical industrial wastewater. These methods are based on the detection of these antibiotics via the formation of chelate complexes with Cu(II). The developed Liquid Chromatographic method offers symmetric peak shape, good resolution and reasonable retention time for both drugs. The removal percentage reached about 100 and 92.1% at pH 7.2 for CFX and CFM, respectively. In UV detection, the removal of the chelating antibiotics were based on forming of chelate complexes with Cu(II) which detected at λmax = 253 and 244 nm for CFX and CFM, respectively. Linearity, accuracy and precision were found to be acceptable over the concentration range of 5.99-59.86 µg mL-1 for CFX and 14.33-71.63 µg mL-1 for CFM. The proposed method can be used for the quality control of industrial wastewater containing CFX and CFM.

Role of Clay Minerals in Natural Media Self-Regeneration from Organic Pollution-Prospects for Nature-Inspired Water Treatments

Pollution from organic molecules is a major environmental issue that needs to be addressed because of the negative impacts of both the harmfulness of the molecule structures and the toxicity that can spread through natural media. This is mainly due to their unavoidable partial oxidation under exposure to air and solar radiation into diverse derivatives. Even when insoluble, the latter can be dispersed in aqueous media through solvatation and/or complexation with soluble species. Coagulation-flocculation, biological water treatments or adsorption on solids cannot result in a total elimination of organic pollutants. Chemical degradation by chlorine and/or oxygen-based oxidizing agents is not a viable approach due to incomplete mineralization into carbon dioxide and other oxides. A more judicious strategy resides in mimicking natural oxidation under ambient conditions. Soils and aqueous clay suspensions are known to display adsorptive and catalytic properties, and slow and complete self-regeneration can be achieved in an optimum time frame with a much slower pollution throughput. A deep knowledge of the behavior of aluminosilicates and of oxidizing species in soils and aquatic media allows us to gain an understanding of their roles in natural oxidative processes. Their individual and combined contributions will be discussed in the present critical analysis of the reported literature.

Harnessing biotechnology for penicillin production: Opportunities and environmental considerations

Since the discovery of antibiotics, penicillin has remained the top choice in clinical medicine. With continuous advancements in biotechnology, penicillin production has become cost-effective and efficient. Genetic engineering techniques have been employed to enhance biosynthetic pathways, leading to the production of new penicillin derivatives with improved properties and increased efficacy against antibiotic-resistant pathogens. Advances in bioreactor design, media formulation, and process optimization have contributed to higher yields, reduced production costs, and increased penicillin accessibility. While biotechnological advances have clearly benefited the global production of this life-saving drug, they have also created challenges in terms of waste management. Production fermentation broths from industries contain residual antibiotics, by-products, and other contaminants that pose direct environmental threats, while increased global consumption intensifies the risk of antimicrobial resistance in both the environment and living organisms. The current geographical and spatial distribution of antibiotic and penicillin consumption dramatically reveals a worldwide threat. These challenges are being addressed through the development of novel waste management techniques. Efforts are aimed at both upstream and downstream processing of antibiotic and penicillin production to minimize costs and improve yield efficiency while lowering the overall environmental impact. Yield optimization using artificial intelligence (AI), along with biological and chemical treatment of waste, is also being explored to reduce adverse impacts. The implementation of strict regulatory frameworks and guidelines is also essential to ensure proper management and disposal of penicillin production waste. This review is novel because it explores the key remaining challenges in antibiotic development, the scope of machine learning tools such as Quantitative Structure-Activity Relationship (QSAR) in modern biotechnology-driven production, improved waste management for antibiotics, discovering alternative path to reducing antibiotic use in agriculture through alternative meat production, addressing current practices, and offering effective recommendations.

Photoacoustic Spectroscopy of Titanium Dioxide, Niobium Pentoxide, Titanium:Niobium, and Ruthenium-Modified Oxides Synthesized Using Sol-Gel Methodology

The aim of this work was the development and morphological/chemical, spectroscopic, and structural characterization of titanium dioxide, niobium pentoxide, and titanium:niobium (Ti:Nb) oxides, as well as materials modified with ruthenium (Ru) with the purpose of providing improvement in photoactivation capacity with visible sunlight radiation. The new materials synthesized using the sol-gel methodology were characterized using the following techniques: scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), photoacoustic spectroscopy (PAS), and X-ray diffraction (XRD). The SEM-EDS analyses showed the high purity of the bases, and the modified samples showed the adsorption of ruthenium on the surface with the crystals' formation and visible agglomerates for higher calcination temperature. The nondestructive characterization of PAS in the ultraviolet visible region suggested that increasing calcination temperature promoted changes in chemical structures and an apparent decrease in gap energy. The separation of superimposed absorption bands referring to charge transfers from the ligand to the metal and the nanodomains of the transition metals suggested the possible absorption centers present at the absorption threshold of the analyzed oxides. Through the XRD analysis, the formation of stable phases such as T-Nb16.8O42, o-Nb12O29, and rutile was observed at a lower temperature level, suggesting pore induction and an increase in surface area for the oxides studied, at a calcination temperature below that expected by the related literature. In addition, the synthesis with a higher temperature level altered the previously existing morphologies of the Ti:Nb, base and modified with Ru, forming the new mixed crystallographic phases Ti2Nb10O29 and TiNb2O7, respectively. As several semiconductor oxide applications aim to reduce costs with photoexcitation under visible light, the modified Ti:Ru oxide calcined at a temperature of 800 °C and synthesized according to the sol-gel methodology used in this work is suggested as the optimum preparation point. This study presented the formation of a stable crystallographic phase (rutile), a significant decrease in gap energy (2.01 eV), and a visible absorption threshold (620 nm).

'Primary' antibiotics in wastewater treatment plants

There are anywhere from 5 to 8 priority antibiotics in typical wastewater treatment plants (WWTPs) whose concentrations exceed the maximum allowed, out of 12 priority antibiotics designated by the World Health Organization as the species to pose severe health hazard than others. If the priority antibiotics to deal with could be reduced to just one or two, such reduction would greatly simplify the construction and operation of the treatment plants. Introduced here is a concept of 'primary' antibiotic, the abatement of which ensures mitigation of all the other priority antibiotics in the wastewater. A criterion for determining primary antibiotic is developed. For a demonstration of the approach, the wastewater systems treated with solar-based photocatalysts are considered. The criterion reveals that the primary antibiotic in the typical European WWTP as well as in the typical municipal and hospital wastewater is ciprofloxacin, whereas the typical industrial wastewater contains ciprofloxacin and oxytetracycline.

A review on hazards and treatment methods of released antibiotics in hospitals wastewater during the COVID-19 pandemic

Drugs and related goods are widely used in order to promote public health and the quality of life. One of the most serious environmental challenges affecting public health is the ongoing presence of antibiotics in the effluents generated by pharmaceutical industries and hospitals. Antibiotics cannot be entirely removed from wastewater using the traditional wastewater treatment methods. Unmetabolized antibiotics generated by humans can be found in urban and livestock effluent. The antibiotic present in effluent contributes to issues with resistance to antibiotics and the creation of superbugs. Over the recent 2 years, the coronavirus disease 2019 pandemic has substantially boosted hospital waste volume. In this situation, a detailed literature review was conducted to highlight the harmful effects of untreated hospital waste and outline the best approaches to manage it. Approximately 50 to 70% of the emerging contaminants prevalent in the hospital wastewater can be removed using traditional treatment strategies. This paper emphasizes the numerous treatment approaches for effectively eliminating emerging contaminants and antibiotics from hospital wastewater and provides an overview of global hospital wastewater legislation and guidelines on hospital wastewater administration. Around 90% of ECs might be eliminated by biological or physical treatment techniques when used in conjunction with modern oxidation techniques. According to this research, hybrid methods are the best approach for removing antibiotics and ECs from hospital wastewater. The document outlines the many features of effective hospital waste management and might be helpful during and after the coronavirus disease 2019 outbreak, when waste creation on all hospitals throughout the globe has considerably increased.

The combination of precipitative softening and ozonation as a pretreatment of ultrafiltration in flowback water treatment: performance and fouling analysis

Ultrafiltration (UF) technology is an efficient shale gas flowback water treatment method. However, severe membrane fouling is the primary restriction on the application of UF technology. Here, we studied the impact of three pretreatments: precipitative softening (PS), precipitative softening, followed by ozonation (PS-O) and ozonation, followed by precipitative softening (O-PS), on pollutants' removal efficiencies and membrane fouling. The results showed that (1) the hardness, bacteria, scaling trend and compatibility with formation water exceeded the requirements for water reuse; (2) pretreatments effectively increased water flux and prolonged ultrafiltration membrane life, and both of them followed the order of PS-O process > O-PS process > PS process; (3) the fouling mechanism was changed from the complete blocking model to the standard blocking model by the PS process and the addition of ozonation enhanced the correlation of standard blocking model; (4) the quality of fracturing liquid prepared by the effluent treated by the PS-O-UF process was the best and satisfied the requirements of slick water. This paper indicated that the PS-O-UF process was suitable for the treatment of Changning shale gas flowback water for reuse.

Oxidative treatment of micropollutants present in wastewater: A special emphasis on transformation products, their toxicity, detection, and field-scale investigations

Micropollutants have become ubiquitous in aqueous environments due to the increased use of pharmaceuticals, personal care products, pesticides, and other compounds. In this review, the removal of micropollutants from aqueous matrices using various advanced oxidation processes (AOPs), such as photocatalysis, electrocatalysis, sulfate radical-based AOPs, ozonation, and Fenton-based processes has been comprehensively discussed. Most of the compounds were successfully degraded with an efficiency of more than 90%, resulting in the formation of transformation products (TPs). In this respect, degradation pathways with multiple mechanisms, including decarboxylation, hydroxylation, and halogenation, have been illustrated. Various techniques for the analysis of micropollutants and their TPs have been discussed. Additionally, the ecotoxicity posed by these TPs was determined using the toxicity estimation software tool (T.E.S.T.). Finally, the performance and cost-effectiveness of the AOPs at the pilot scale have been reviewed. The current review will help in understanding the treatment efficacy of different AOPs, degradation pathways, and ecotoxicity of TPs so formed.

Combining fungal bioremediation and ozonation for rinse wastewater treatment

In this work, agricultural rinse wastewater, which is produced during the cleaning of agricultural equipment and constitutes a major source of pesticides, was treated by fungal bioremediation and ozonation, both individually and combined in a two-stage treatment train. Three major pesticides (thiacloprid, chlortoluron, and pyrimethanil) were detected in rinse wastewater, with a total concentration of 38.47 mg C L-1. Comparing both technologies, ozonation in a stirred reactor achieved complete removal of these pesticides (720 min) while proving to be a more effective approach for reducing colour, organic matter, and bacteria. However, this technique produced transformation products and increased toxicity. In contrast, fungal bioremediation in a rotating drum bioreactor attenuated toxicity levels and did not produce such metabolites, but only removed approximately 50 % of target pesticide - hydraulic retention time (HRT) of 5 days - and obtained worse results for most of the general quality parameters studied. This work also includes a preliminary economic assessment of both technologies, revealing that fungal bioremediation was 2 times more cost-effective than ozonation. The treatment train, consisting of a first stage of fungal bioremediation followed by ozonation, was found to be a promising approach as it synergistically combines the advantages of both treatments, achieving high removals of pesticides (up to 100 %) and transformation products, while reducing operating costs and producing a biodegradable effluent. This is the first time that fungal bioremediation and ozonation technologies have been compared and combined in a treatment train to deal with pesticides in agricultural rinse wastewater.

Temperature and nitrogen-induced modification of activated carbons for efficient catalytic ozonation of salicylic acid as a model emerging pollutant

The occurrence of emerging pollutants on effluents of wastewater treatment plants makes unfeasible their reutilization and consequently to comply with the sixth goal of 2030 Agenda for sustainable development. Thus, it is extremely important to find ways to remove these pollutants without compromising the quality of reclaimed water. Ozonation has been successfully explored for this purpose, but it still presents limitations towards some oxidant-resistant pollutants. To surpass this, the conversion of ozone (O3) into more reactive species is required, which can be accomplished by using catalysts. Carbon catalysts, such as activated carbons (ACs), represent a more environmentally attractive option than traditional metal-based catalysts, with the advantage of being easily modified to tune their textural and surface properties to the reaction chemistry. In this study, two different sources of ACs were tested in the catalytic ozonation of a frequently detected emerging pollutant: salicylic acid (SalAc). These ACs were submitted to thermal treatment under H2 and functionalization with N precursors, such as melamine and poly(ethyleneimine), to induce changes in the surface properties, especially in the nitrogen content. Although no correlation was found between the N-content and catalytic activity, the thermal treatment under H2 increased the mesopores surface area (Smeso), which reflected in greater catalytic activity. As that, the best-performing AC was the one with the highest Smeso, which revealed also to be resistant to O3 and able to convert O3 into more reactive species, evidenced by the capacity of oxalic acid, a well-known ozone-resistant by-product. The same AC was then submitted to three consecutive reutilization cycles and a more significant activity loss was observed in terms of SalAc degradation rate (⁓ 40%) then total organic carbon removal (⁓ 25%), from the first to the third cycle. This decline in efficiency was ascribed to the presence of by-products adhered to the catalyst surface, which impede its ability to react effectively with O3.

Evaluation of the prediction of micropollutant elimination during bromide ion-containing industrial wastewater ozonation using the ROH, O3 value

The composition of the wastewater matrix influences the oxidation potential of ozonation, a technique widely recognized efficient removal of micropollutants. Here, we developed a chemical kinetic model to determine the ozone dose required to minimize bromate production in wastewater containing bromine ions while achieving target removal rates. In wastewater ozonation, ozone decomposition comprises instantaneous ozone consumption and subsequent decomposition at first-order reaction rates. Under the injection condition of 1.5 g O3/g dissolved organic carbon (DOC), the instantaneous ozone demand was 62.7% of the injection concentration, and it increased proportionally with increasing injected ozone concentration. Ozone and hydroxyl radical exposures were proportional to the initial ozone dose, while hydroxyl radical exposure was proportional to ozone exposure, and the deviation was relatively high at 1.0-1.5 g O3/g DOC. The calculated hydroxyl radical exposure was 3.0 × 10-10 to 5.3 × 10-10 M s. Ozone and hydroxyl radicals are highly correlated with the ratio of ozone dose to organic matter concentration. Therefore, a trace substance removal rate evaluation model combined with the ROH, O3 model and a bromate generation model were also considered. For ibuprofen, the ozone dose for achieving the target removal rate of 80% while maintaining the bromate concentration below 50 μg L-1 was suitable in the operating range of 0.86 g O3/g DOC or more. The proposed method provides a practical operation strategy to calculate the appropriate ozone dose condition from the target compound removal rate prediction and bromate generation models considering the ratio of ozone dose to organic matter concentration in the incoming wastewater.

A combined treatment system of O3/UV oxidation and activated carbon adsorption: emerging contaminants in hospital wastewater

Researchers have recently focused their attention on emerging contaminants (ECs) in wastewater because they pose serious health and environmental risks. Because ECs are persistent in the environment and have the ability to disrupt the physiology of target receptors, they have been labeled as contaminants of recent environmental concern. For removing various ECs, a variety of treatment technologies have been developed, including biological, chemical, and physical methods. However, no single technology can currently effectively remove ECs, whereas hybrid systems have consistently proven to be more effective. Furthermore, the majority of existing technologies are energy and resource intensive, as well as expensive to maintain and operate. Furthermore, the majority of advanced treatment technologies that have been proposed have yet to be evaluated for large-scale feasibility. Some ECs, particularly pharmaceuticals and pesticides, were found to be significantly removed using a hybrid technique that included ozone/UV and granular activated carbon (GAC). Besides, the removal of effluent parameters (TDS, COD, TOC) was enhanced through the GAC surface oxidization as a catalyst with NaOH before the process and by ozone within the procedure as well.

Disinfection of treated urban effluents for reuse by combination of coagulation/flocculation and Fenton processes

In this study, a combination of coagulation/flocculation and Fenton processes was studied as tertiary treatment in order to generate treated water susceptible to reuse. The combination of both processes has never been applied in disinfection of real urban wastewater. The best removals of turbidity and enterobacteria were achieved when applying a coagulant (FeCl₃) dosage of 120 mg/L and the natural pH of the effluent (7.14). The following Fenton reaction presented the maximal enterobacteria inactivation after 120 min at 25 °C, when using hydrogen peroxide and added iron concentrations of 100 mg/L and 7 mg/L, respectively. The abundance of antibiotic resistant (amoxicillin and sulfamethoxazole) enterobacteria and total enterobacteria, enterococci, and heterotrophs, and antibiotic resistance genes - ARG - (sul1, bla_TEM and qnrS) was evaluated before and after each step of the treatment. Values below 10 CFU/100 mL were achieved for total and resistant cultivable enterobacteria immediately after treatment and after storage for 72 h, therefore meeting the strictest limit imposed for E. coli. Physico-chemical parameters also met the established limits for water reuse. Despite harbouring a rich and diverse bacterial community, the final stored disinfected wastewater contained high relative abundance of potentially hazardous bacteria. Such results point out the need of a deep microbiological characterization of treated wastewater to evaluate the risk of its reuse in irrigation.

Removing chemical and biological pollutants from swine wastewater through constructed wetlands aiming reclaimed water reuse

Reusing reclaimed wastewater is needed to fight water scarcity, reduce freshwater consumption and conserve water resources, but one must ensure that hazardous substances are fully removed/eliminate before that reuse. The potential of lab-scale constructed wetlands (CWs) for the removal of chemical and biological contaminants from livestock wastewater, while maintaining nutrient levels for fertilization, was assessed, evaluating changes in microbial communities, with particular focus on potential pathogens. CW microcosms with two different substrates (lava rock or light expanded clay aggregate), both planted with Phragmites australis, were tested. After 15 days of treatment, removal rates were higher than 80% for Cd, Cr, Cu, Fe, Pb and Zn, in general with no significant differences between the two different substrates. Organic matter and nutrients were also removed but their levels still allowed the used of the treated wastewater as a fertilizer Removal of bacterial contamination was estimated through enumeration of cultivable bacteria. High removal rates of fecal indicator bacteria were observed, reaching >95% for enterococci and >98% for enterobacteria after 15 days of treatment, decreasing hazardous biological contaminants initially present in the wastewater. In addition, the microbial communities in the initial and treated wastewater, and in the plant roots bed substrate, were characterized by using 16SrRNA gene amplicon sequencing. Microbial communities in the CW systems showed a clear shift comparatively with the initial wastewater showing system adaptation and removal potentialities. This also revealed an important removal of the most represented potential pathogenic genus, Clostridium, which relative abundance decreased from 33% to 1% through the treatment. Overall, CWs showed potential to be efficient in removing chemical and biological contaminants, while maintaining moderated levels of nutrients, allowing the reuse of reclaimed water in agriculture, namely as fertilizer. Current results will contribute for the optimization and use of CWs for a sustainable treatment of liquid wastes, promoting the circular economy.

Recent advances in sterilization and disinfection technology: A review

Sterilization and disinfection of pollutants and microorganisms have been extensively studied in order to address the problem of environmental contamination, which is a crucial issue for public health and economics. Various form of hazardous materials/pollutants including microorganisms and harmful gases are released into the environment that enter into the human body either through inhalation, adsorption or ingestion. The human death rate rises due to various respiratory ailments, strokes, lung cancer, and heart disorders related with these pollutants. Hence, it is essential to control the environmental pollution by applying economical and effective sterilization and disinfections techniques to save life. In general, numerous forms of traditional physical and chemical sterilization and disinfection treatments, such as dry and moist heat, radiation, filtration, ethylene oxide, ozone, hydrogen peroxide, etc. are known along with advanced techniques. In this review we summarized both advanced and conventional techniques of sterilization and disinfection along with their uses and mode of action. This review gives the knowledge about the advantages, disadvantages of both the methods comparatively. Despite, the effective solution given by the advanced sterilization and disinfection technology, joint technologies of sterilization and disinfection has proven to be more effective innovation to protect the indoor and outdoor environments.

Antibiotic resistant bacteria: A bibliometric review of literature

Antibiotic-resistant bacteria (ARB) are a serious threat to the health of people and the ecological environment. With this problem becoming more and more serious, more countries made research on the ARB, and the research number has been sharply increased particularly over the past decade. Therefore, it is quite necessary to globally retrace relevant researches on the ARB published from 2010 to 2020. This will help researchers to understand the current research situation, research trends and research hotspots in this field. This paper uses bibliometrics to examine publications in the field of ARB from 2010 to 2020 that were retrieved from the Web of Science (WOS). Our study performed a statistical analysis of the countries, institutions, journals, authors, research areas, author keywords, Essential Science Indicators (ESI) highly cited papers, and ESI hotspots papers to provide an overview of the ARB field as well as research trends, research hotspots, and future research directions in the field. The results showed that the number of related studies is increasing year by year; the USA is most published in the field of ARB; China is the most active in this field in the recent years; the Chinese Acad Sci published the most articles; Sci. Total Environ. published the greatest number of articles; CM Manaia has the most contributions; Environmental Sciences and Ecology is the most popular research area; and "antibiotic resistance," "antibiotics," and "antibiotic resistance genes" were the most frequently occurring author keywords. A citation analysis showed that aquatic environment-related antibiotic resistance is a key research area in this field, while antimicrobial nanomaterial-related research is a recent popular topic.

Sulfide-Doped Magnetic Carbon Nanotubes Developed as Adsorbent for Uptake of Tetracycline and Cefixime from Wastewater

In this study, a magnetic solid-phase extraction method was developed based on multi-wall carbon nanotubes decorated by magnetic nanoparticles (Fe₃O₄) and cadmium sulfide nanoparticles (Fe₃O₄@MWCNT-CdS) for trace extraction of cefixime and tetracycline antibiotics from urine and drug company wastewater. The adsorbent features were characterized by Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscope (FESEM), and energy dispersive X-ray analysis (EDX). Various effective parameters on the sorption and desorption cycle, such as sorption time, the mass of adsorbent, pH, salt addition, and material ratio, were investigated and optimized. The data were evaluated using isotherm models, and experimental data were well-fitted to both Langmuir (R² = 0.975) and Freundlich (R² = 0.985) models. Moreover, kinetic of reaction was agreement with pseudo-second-order (R² = 0.999) as compared pseudo-first-order (R² = 0.760). The maximum adsorption capacity for tetracycline and cefixime was achieved at 116.27 and 105.26 mg·g^-1, respectively. Hence, the prepared adsorbent can be used as an alternative material for enhanced determination of pharmaceutical substances in biological fluids.

Advanced wastewater treatment with ozonation and granular activated carbon filtration: Inactivation of antibiotic resistance targets in a long-term pilot study

The inactivation of antibiotic resistant bacteria (ARB) and genes (ARGs) in an advanced plant combining ozonation and granular activated carbon (GAC) filtration applied for effluent after conventional activated sludge treatment at a full-scale urban wastewater treatment plant was investigated for over 13 consecutive months. The nitrite compensated specific ozone dose ranged between 0.4 and 0.7 g O₃/g DOC with short-time sampling campaigns (0.2-0.9 g O₃/g DOC). Samples were analysed with culture-dependent methods for bacterial targets and with qPCR for genes. The log removal values were correlated with a decrease of the matrix UV absorption at 254 nm (ΔUV₂₅₄) and indicated a range of ΔUV₂₅₄ that corresponds to a sufficient membrane damage to affect DNA. For trimethoprim/sulfamethoxazole resistant E. coli, sul1, ermB and tetW, this phase was observed at ΔUV₂₅₄ of ~30 % (~0.5 g O₃/g DOC). For ampicillin resistant E. coli and bla_TEM-1, it was observed around 35-40 % (~0.7 g O₃/g DOC), which can be linked to mechanisms related to oxidative damages in bacteria resistant to bactericidal antibiotics. GAC treatment resulted in a further abatement for trimethoprim/sulfamethoxazole E. coli, sul1 and tetW, and in increase in absolute and relative abundance of ermB and bla_TEM-1.

Nanostructured photocatalysts for the abatement of contaminants by photocatalysis and photocatalytic ozonation: An overview

The water scarcity, the presence of different contaminants in the worldwide waters and wastewaters and their impacts should motivate their good elimination and water management. With this, photocatalysis and photocatalytic ozonation are strong solutions to obtain good quality reclaimed water, for different applications. Nanostructured supported photo-active catalysts, such as the TiO₂, WO₃ or ZnO can positively affect the performance of such technologies. Therefore, different semiconductors materials have been aroused the interest of the scientific community, mainly due to its functional properties as well as characteristics imposed by the different nanostructures. With this, this work overviews different works and perspective on the TiO₂ nanotubes and other semiconductors nanostructures, with the analysis of different works from 2001 to 2022. Aspects as the substrate effect, electrolyte nature, aspect ratio, electrolyte aging, and annealing treatment but also the effect of morphology, anodization time, applied voltage, temperature and viscosity are discussed. Modification of TiO₂ nanotubes is also presented in this paper. The main objective of this work is to present and discuss the key parameters and their effects on the anodization of different semiconductors, as well as the results obtained until today on the degradation of different contaminants by photocatalysis and photocatalytic ozonation, as well as their use on the treatment of real wastewater. TiO₂ nanotubes present unique properties and highly ordered configuration, which motivate their use on photo-driven technologies for the pollutant's abatement, even when compared to other nanostructures. However, photocatalysts with activity on the visible range and solar radiation, such as the WO₃, can present higher performance and can decrease operational costs, and must be an important source and a key to find efficient and cost-friendly solutions.

Optimization, Nature, and Mechanism Investigations for the Adsorption of Ciprofloxacin and Malachite Green onto Carbon Nanoparticles Derived from Low-Cost Precursor via a Green Route

The spread of organic pollutants in water spoils the environment, and among the best-known sorbents for removing organic compounds are carbonaceous materials. Sunflower seed waste (SFSW) was employed as a green and low-cost precursor to prepare carbon nanoparticles (CNPs) via pyrolysis, followed by a ball-milling process. The CNPs were treated with a nitric–sulfuric acid mixture (1:1) at 100 °C. The scanning electron microscopy (SEM) showed a particle size range of 38 to 45 nm, and the Brunauer–Emmett–Teller (BET) surface area was 162.9 m2 g−1. The elemental analysis was performed using energy-dispersive X-ray spectroscopy, and the functional groups on the CNPs were examined with Fourier transform infrared spectroscopy. Additionally, an X-ray diffractometer was employed to test the phase crystallinity of the prepared CNPs. The fabricated CNPs were used to adsorb ciprofloxacin (CFXN) and malachite green (MLG) from water. The experimentally obtained adsorption capacities for CFXN and MLG were 103.6 and 182.4 mg g−1, respectively. The kinetic investigation implied that the adsorption of both pollutants fitted the pseudo-first-order model, and the intraparticle diffusion step controlled the process. The equilibrium findings for CFXN and MLG sorption on the CNPs followed the Langmuir and the Fredulich isotherm models, respectively. It was concluded that both pollutants spontaneously adsorbed on the CNPs, with physisorption being the likely mechanism. Additionally, the FTIR analysis of the adsorbed CFXN showed the disappearance of some functional groups, suggesting a chemisorption contribution. The CNPs showed an excellent performance in removing CFXN and MLG from groundwater and seawater samples and possessed consistent efficiency during the recycle–reuse study. The application of CNPs to treat synthetically contaminated natural water samples indicated the complete remediation of polluted water using the ball-mill-fabricated CNPs.

Fate of antibiotic resistant genes in wastewater environments and treatment strategies - A review

Antibiotic-resistant bacteria (ARB) and antibiotic-resistant genes (ARGs) have emerged in aquatic environments through the discharge of large amounts of antibiotics into wastewater. Well-designed wastewater treatment plants (WWTPs) with effective treatment processes are essential to prevent the release of ARGs directly into the environment. Although some systematic sequential treatment methods are used to remove ARGs, considerable gaps in removal mechanisms will be discussed. Therefore, deep analysis and discussion of various treatment methods are required to understand the ARGs removal mechanisms. In this manuscript, the role of antibiotics and the resistance mechanism of ARB are discussed in depth. In addition, the fate of ARGs in an aquatic environment and detection methods are compared comprehensively and discussed. In particular, the advantages and disadvantages of various methods are summarized and reviewed critically. Finally, combined technologies, such as advanced oxidation process (AOP) with biochemical systems, membrane separation with electrochemical AOP, ultrafiltration (UF) membrane coupled with photocatalytic treatment, and UF membrane separation coupled with sonication, are introduced. Overall, low-energy anaerobic treatment reactors with any of the above combined treatments might reduce the discharge of large quantities of ARGs into the environment. Finally, this review provides valuable insights for better ARG removal technologies by introducing combined effective treatment strategies used in real WWTPs.

Antibiotics removal from aquaculture effluents by ozonation: chemical and toxicity descriptors

Antibiotics are often applied in aquaculture to prevent fish diseases. These substances can cause disturbances on receiving waters, when not properly eliminated from the aquaculture effluents. In this work, ozone (O₃) was investigated as a possible oxidizing agent to remove fishery antibiotics from aquaculture effluents: florfenicol (FF), oxytetracycline (OTC), sulfadimethoxine (SDM), sulfamethoxazole (SMX), and trimethoprim (TMP). Batch experiments were performed using ultrapure water and aquaculture effluents spiked with a mixture of target antibiotics at relatively high concentrations (10 mg L^-1 each). OTC, SMX and TMP were fully removed (< 30 min) regardless of the tested conditions, mainly by O₃ direct attack. In contrast, FF was partially removed in 30 min (∼ 10 and 60%, in aquaculture effluents and ultrapure water, respectively), but only in the presence of hydroxyl radicals (HO^•), the FF concentrations reaching levels below the detection limits in ultrapure water after 60 min. In the case of SDM, its degradation was highly influenced by the selected water matrix, but with removals always higher than 68%. In continuous-flow experiments applying more environmentally relevant antibiotic concentrations (100 ng L^-1 each) and low O₃ doses (1.5 mg L^-1), ozonation highly removed (> 98%) all tested antibiotics from aquaculture effluents with a hydraulic retention time (HRT) of 10 min, except FF (68%). Although by-products were detected in treated samples, zebrafish (Danio rerio) embryotoxicity tests did not show a toxicity increase by applying this ozonation treatment. Ozonation is thus a possible solution to remove antibiotics from aquaculture effluents. Still, full-scale studies in aquaculture farms are needed, and generation of HO^• may be favoured to readily oxidize the FF antibiotic.

Degradation of chloramphenicol by Ti/PbO2-La anodes and alteration in bacterial community and antibiotics resistance genes

Antibiotics accumulation in the environment has given rise to multi-drug resistant 'superbugs' and antibiotics resistence genes (ARGs). Chloramphenicol (CAP), a kind of widely used antibiotics, was chosen as the model compound to investigate its degradation during electrochemical treatment process. The prepared Ti/PbO₂-La electrodes had a denser surface and a more complete PbO₂ crystal structure than Ti/PbO₂ electrode. The doping of La increased the onset potential and the overpotential, increased the current value of the oxidation peak and the reduction peak, reduced the impedance, and increased the lifetime. The reactions CAP degradation and TOC removal on Ti/PbO₂-La electrode was both primary kinetic reactions. CAP degradation rate increased with current density, and TOC obtained the highest removal at current density of 25 mA cm^-2. The electrolyte concentration had a small effect in the range of 0.050-0.150 mol L^-1. The effects under acidic and neutral conditions were better than under alkaline conditions. CAP was mainly directly oxidized at the electrode surface and indirect oxidation also took place via generated ·OH and SO₄^·-. 15 intermediates and 2 degradation pathways have been postulated. The entry of CAP and CAP intermediates into the environment caused the alteration in bacterial community and ARGs, while complete degradation products had little effect on them. Redundancy analysis showed that intI1 was the dominant factor affecting ARGs, and Actinobacteria and Patescibacteria were the main factors affecting the abundances of ARGs in the microbial community.

Sustainable adsorptive removal of antibiotic residues by chitosan composites: An insight into current developments and future recommendations

During COVID-19 crisis, water pollution caused by pharmaceutical residuals have enormously aggravated since millions of patients worldwide are consuming tons of drugs daily. Antibiotics are the preponderance pharmaceutical pollutants in water bodies that surely cause a real threat to human life and ecosystems. The excellent characteristics of chitosan such as nontoxicity, easy functionality, biodegradability, availability in nature and the abundant hydroxyl and amine groups onto its backbone make it a promising adsorbent. Herein, we aimed to provide a comprehensive overview of recent published research papers regarding the removal of antibiotics by chitosan composite-based adsorbents. The structure, ionic form, optimum removal pH and λmax of the most common antibiotics including Tetracycline, Ciprofloxacin, Amoxicillin, Levofloxacin, Ceftriaxone, Erythromycin, Norfloxacin, Ofloxacin, Doxycycline, Cefotaxime and Sulfamethoxazole were summarized. The development of chitosan composite-based adsorbents in order to enhance their adsorption capacity, reusability and validity were presented. Moreover, the adsorption mechanisms of these antibiotics were explored to provide more information about adsorbate-adsorbent interactions. Besides the dominant factors on the adsorption process including pH, dosage, coexisting ions, etc. were discussed. Moreover, conclusions and future recommendations are provided to inspire for further researches.

Does light-based tertiary treatment prevent the spread of antibiotic resistance genes? Performance, regrowth and future direction

The common occurrence of antibiotic-resistance genes (ARGs) originating from pathogenic and facultative pathogenic bacteria pose a high risk to aquatic environments. Low removal of ARGs in conventional wastewater treatment processes and horizontal dissemination of resistance genes between environmental bacteria and human pathogens have made antibiotic resistance evolution a complex global health issue. The phenomenon of regrowth of bacteria after disinfection raised some concerns regarding the long-lasting safety of treated waters. Despite the inactivation of living antibiotic-resistant bacteria (ARB), the possibility of transferring intact and liberated DNA containing ARGs remains. A step in this direction would be to apply new types of disinfection methods addressing this issue in detail, such as light-based advanced oxidation, that potentially enhance the effect of direct light interaction with DNA. This study is devoted to comprehensively and critically review the current state-of-art for light-driven disinfection. The main focus of the article is to provide an insight into the different photochemical disinfection methods currently being studied worldwide with respect to ARGs removal as an alternative to conventional methods. The systematic comparison of UV/chlorination, UV/H₂O₂, sulfate radical based-AOPs, photocatalytic processes and photoFenton considering their mode of action on molecular level, operational parameters of the processes, and overall efficiency of removal of ARGs is presented. An in-depth discussion of different light-dependent inactivation pathways, influence of DBP and DOM on ARG removal and the potential bacterial regrowth after treatment is presented. Based on presented revision the risk of ARG transfer from reactivated bacteria has been evaluated, leading to a future direction for research addressing the challenges of light-based disinfection technologies.

Application of iron-activated persulfate for municipal wastewater disinfection

To address the increasing contamination of aquatic environments and incidence of waterborne diseases, advanced oxidation processes with activated persulfate have emerged as tools to inactivate wastewater microorganisms and contaminants. In this work, the disinfection of a secondary effluent from a wastewater treatment plant by iron-based persulfate activation was studied. Experiments in a batch stirred tank reactor were carried out to evaluate the performance along reaction time and the effect of operational parameters in the oxidative process efficiency (oxidant and iron concentration, pH and temperature). After 60 min of reaction, persulfate and iron concentrations of 3 mM and 0.75 mM, respectively, combined with a neutral initial pH (7.5) and a temperature of 40 °C, allowed to reach values below the detection limit (<10 CFU/100 mL) of enterococci and enterobacteria with and without ciprofloxacin resistance, as well as a 91% inactivation of total heterotrophic organisms and a 70% removal of total organic carbon. Regrowth of microorganisms was evaluated 72 h after treatment and it was only noticed a slight increase in total heterotrophs. Evaluation of physico-chemical characteristics of the treated water showed that it meets the requirements imposed by European and Portuguese legislation for its reuse in irrigation and most urban utilities.

Effect of ozonation-based disinfection methods on the removal of antibiotic resistant bacteria and resistance genes (ARB/ARGs) in water and wastewater treatment: a systematic review

Antibiotic resistance is considered a universal health threat of the 21st century which its distribution and even development are mainly mediated by water-based media. Disinfection processes with the conventional methods are still the most promising options to combat such crises in aqueous matrices especially wastewater. Knowing that the extent of effectiveness and quality of disinfection is of great importance, this paper aimed to systematically review and discuss ozonation (as one of the main disinfectants with large scale application) effect on removing antibiotic resistant bacteria (ARB) and antibiotic resistance genes (ARGs) from aqueous solutions, for which no study has been reported. For this, a comprehensive literature survey was performed within the international databases using appropriate keywords which yielded several studies involving different aspects and the effectiveness extent of ozonation on ARB & ARGs. The results showed that no definite conclusion could be drawn about the superiority of ozone alone or in a hybrid form. Mechanism of action was carefully evaluated and discussed although it is still poorly understood. Evaluation of the studies from denaturation and repairment perspectives showed that regrowth cannot be avoided after ozonation, especially for some ARB & ARGs variants. In addition, the comparison of the effectiveness on ARB & ARGs showed that ozonation is more effective for resistant bacteria than their respective genes. The degradation efficiency was found to be mainly influenced by operational parameters of CT (i.e. ozone dose & contact time), solids, alkalinity, pH, and type of pathogens and genes. Moreover, the correlation between ARB & ARGs removal and stressors (such as antibiotic residuals, heavy metals, aromatic matters, microcystins, opportunistic pathogens, etc.) has been reviewed to give the optimal references for further in-depth studies. The future perspectives have also been reported.

Advanced oxidation technologies and constructed wetlands in aquaculture farms: What do we know so far about micropollutant removal?

Aquaculture is the fastest growing animal food-producing sector. Water is the central resource for aquaculture, and it is essential that its quality be preserved. Micropollutants (MPs) can reach aquaculture through anthropogenic addition or inlet water, and may cause harmful effects such as endocrine disruption and antibiotic resistance, adversely affecting the fish species being farmed. Furthermore, the discharge of aquaculture effluents into the environment may contribute to the deterioration of water courses. In this sense, the implementation of environmentally responsible measures in aquaculture farms is imperative for the protection of ecosystems and human health. The European Commission (EC) has recently launched a guiding document promoting ecological aquaculture practices; however, options for water treatment are still lacking. Conventional processes are not designed to deal with MPs; this review article consolidates relevant information on the application of advanced oxidation technologies (AOTs) and constructed wetlands (CWs) as potential strategies in this regard. Although 161 studies on the application of AOTs or CWs in aquaculture have already been published, only 34 focused on MPs (28 on AOTs and 6 on CWs), whereas the others reported the removal of contaminants such as bacteria, organic matter, solids and inorganic ions. No study coupling both treatments has been reported to date for the removal of MPs from aquaculture waters. AOTs and CWs are prospective alternatives for the treatment of aquacultural aqueous matrices. However, the type of aquaculture activity and the specifications of these available technologies should be considered while selecting the most suitable treatment option.

The removal of antibiotic resistant bacteria and genes and inhibition of the horizontal gene transfer by contrastive research on sulfidated nanoscale zerovalent iron activating peroxymonosulfate or peroxydisulfate

Antibiotic resistant bacteria (ARB) and the antibiotic resistance genes (ARGs) dissemination via plasmid-mediated conjugation have attracted considerable attentions. In this research, sulfidated nanoscale zerovalent iron (S-nZVI)/peroxymonosulfate (PMS) and S-nZVI/peroxydisulfate (PDS) process were investigated to inactivate ARB (Escherichia coli DH5α with RP4 plasmid, Pseudomonas. HLS-6 contains sul1 and intI1 on genome DNA sequence). S-nZVI/PMS system showed higher efficiency than S-nZVI/PDS on ARB inactivation. Thus, the optimal condition 28 mg/L S-nZVI coupled with 153.7 mg/L (0.5 mM) PMS was applied to remove both intracellular ARGs (iARGs) and ARB. The oxidative damage of ARB cell was systemically studied by cell viability, intracellular Mg²⁺ levels, the changes of extracellular and internal structure, integrity of cell walls and membranes and enzymatic activities. S-nZVI/PMS effectively inactivated ARB (~7.32 log) within 15 min. These effects were greatly higher than those achieved individually. Moreover, removal efficiencies of iARGs sul1, intI1 and tetA were 1.52, 1.79 and 1.56 log, respectively. These results revealed that S-nZVI and PMS have a synergistic effect against ARB and iARGs. The regrowth assays illustrated that the ARB were effectively inactivated. By verifying the inhibitory impacts of S-nZVI/PMS treatment on conjugation transfer, this work highlights a promising alternative technique for inhibiting the horizontal gene transfer.

Overgrowth control of potentially hazardous bacteria during storage of ozone treated wastewater through natural competition

Improving the chemical and biological quality of treated wastewater is particularly important in world regions under water stress. In these regions, reutilization of wastewater is seen as an alternative to reduce water demand, particularly for agriculture irrigation. In a reuse scenario, the treated wastewater must have enough quality to avoid chemical and biological contamination of the receiving environment. Ozonation is among the technologies available to efficiently remove organic micropollutants and disinfect secondary effluents, being implemented in full-scale urban wastewater treatment plants worldwide. However, previous studies demonstrated that storage of ozone treated wastewater promoted the overgrowth of potentially harmful bacteria, putting at risk its reutilization, given for instance the possibility of contaminating the food-chain. Therefore, this study was designed to assess the potential beneficial role of inoculation of ozone treated wastewater with a diverse bacterial community during storage, for the control of the overgrowth of potentially hazardous bacteria, through bacterial competition. To achieve this goal, ozone treated wastewater (TWW) was diluted with river water (RW) in the same proportion, and the resulting bacterial community (RW+TWW) was compared to that of undiluted TWW over 7 days storage. As hypothesized, in contrast to TWW, where dominance of Beta- and Gammaproteobacteria, namely Pseudomonas spp. and Acinetobacter spp., was observed upon storage for 7 days, the bacterial communities of the diluted samples (RW+TWW) were diverse, resembling those of RW. Moreover, given the high abundance of antibiotic resistance genes in RW, the concentration of these genes in RW+TWW did not differ from that of the non-ozonated controls (WW, RW and RW+WW) over the storage period. These results highlight the necessity of finding a suitable pristine diverse bacterial community to be used in the future to compete with bacteria surviving ozonation, to prevent reactivation of undesirable bacteria during storage of treated wastewater.

Recent Progress and Prospects in Catalytic Water Treatment

Presently, conventional technologies in water treatment are not efficient enough to completely mineralize refractory water contaminants. In this context, the implementation of catalytic processes could be an alternative. Despite the advantages provided in terms of kinetics of transformation, selectivity, and energy saving, numerous attempts have not yet led to implementation at an industrial scale. This review examines investigations at different scales for which controversies and limitations must be solved to bridge the gap between fundamentals and practical developments. Particular attention has been paid to the development of solar-driven catalytic technologies and some other emerging processes, such as microwave assisted catalysis, plasma-catalytic processes, or biocatalytic remediation, taking into account their specific advantages and the drawbacks. Challenges for which a better understanding related to the complexity of the systems and the coexistence of various solid-liquid-gas interfaces have been identified.

Effective electrocatalytic elimination of chloramphenicol: mechanism, degradation pathway, and toxicity assessment

The residual antibiotics in different environmental media pose a serious threat to human health and the ecosystem. The high-efficient elimination of antibiotics is one of the foremost works. In this study, chloramphenicol (CAP) was eliminated efficiently by electrocatalytic advanced oxidation process with carbon nanotubes/agarose/indium tin oxide (CNTs/AG/ITO) electrode. The influences of different experimental parameters on the degradation efficiency were systematically studied. Under the optimal conditions (4 V potential, 10 wt% CNTs dosage, and pH = 10), the maximum degradation efficiency of CAP (20 mg L-1) achieved 88% within 180 min. Besides, the electrocatalytic degradation pathway and mechanism for CAP were also investigated, •O2- played a major role in the process of electrocatalytic degradation. Based on the QSAR (quantitative structure-activity relationship) model, the toxicities of CAP and identified intermediates were analyzed. Compared with the parent compound, the maximal chronic toxicity of intermediate ((E)-3-(4-nitrophenyl)prop-1-ene-1,3-diol) for daphnid increased 197-fold. Besides, the hybrid toxicity of the degradation system was further confirmed via disk agar biocidal tests with Escherichia coli ATCC25922, which changed slightly during the degradation process. Based on the above results, it is worth noting that the degradation pathway and toxicity assessment should be paid more attention to the treatment of antibiotic wastewater.

Photo-mediated and advanced oxidative processes applied for the treatment of effluents with drugs used for the treatment of early COVID-19: Review

The COVID-19 pandemic is proving to be one of the most challenging health and social crises ever faced by humanity. Several drugs have been proposed as potential antiviral agents for the treatment of COVID-19 since the beginning of the health crisis. Among them are chloroquine (CQ), hydroxychloroquine (HCQ), ivermectin (IVM), and the combination of QC or HCQ and azithromycin (AZI). The use of these and several other drugs has grown sharply, even if there is proof of ineffectiveness in the early treatment or mild cases of COVID-19. Thus, there is great concern about the potential environmental impacts of the effluents released with the presence of these drugs. Therefore, this work aimed to carry out a literature review on wastewater treatment processes, focusing on removing these substances through advanced oxidation process. As the conventional effluent treatment processes do not have high efficiency for removal, it was concentrated in the literature that had as scope advanced and photo-mediated techniques to remove CQ, HCQ, IVM, and AZI. It is expected, with this work, to highlight the importance of conducting research that contributes to the control of pollution and contamination.

Recent advances in structural modifications of photo-catalysts for organic pollutants degradation - A comprehensive review

Over the last few years, industrial and anthropogenic activities have increased the presence of organic pollutants such as dyes, herbicides, pesticides, analgesics, and antibiotics in the water that adversely affect human health and the environment worldwide. Photocatalytic treatment is considered a promising, economical, effective, and sustainable process that utilizes light energy to degrade the pollutants in water. However, certain drawbacks like rapid recombination and low migration capability of photogenerated electrons and holes have restricted the use of photo-catalysts in industries. Hence, despite the abundance of lab-scale research, the technology is still not much commercialized in the mainstream. Several structural modifications in the photo-catalysts have been adopted to enhance the pollutant degradation performance to overcome the same. In this context, the present review article outlines the different advanced heterostructures synthesized to date for improved degradation of three major organic pollutants: antibiotics, dyes, and pesticides. Moreover, the article also emphasizes the degradation kinetics of photo-catalysts and the publication trend in the past decade along with the roadblocks preventing the transfer of technology from the laboratory to industry and new age photo-catalysts for the profitable implications in industrial sectors.

Hydrothermal synthesis of magnetic nano-CoFe2O4 catalyst and its enhanced degradation of amoxicillin by activated permonosulfate

Advanced oxidation process (AOP) has attracted widespread attention because it can effectively remove antibiotics in water, but its practical engineering application is limited by the problems of the low efficiency and difficult recovery of the catalyst. In the study, nano-spinel CoFe₂O₄ was prepared by hydrothermal method and served as the peroxymonosulfate (PMS) catalyst to degrade antibiotic amoxicillin (AMX). The reaction parameters such as CoFe₂O₄ dosage, AMX concentration, and initial pH value were also optimized. The reaction mechanism was proposed through free radical capture experiment and possible degradation pathway analysis. In addition, the magnetic recovery performance and stability of the catalyst were evaluated. Results showed that 85.5% of AMX could be removed within 90 min at optimal conditions. Sulfate radicals and hydroxyl radicals were the active species for AMX degradation. Moreover, the catalyst showed excellent magnetism and stability in the cycle experiment, which has great potential in the AOP treatment of antibiotic polluted wastewater.

Novel Silanized Graphene Oxide/TiO2 Multifunctional Nanocomposite Photocatalysts: Simultaneous Removal of Cd2+ and Photodegradation of Phenols under Visible Light Irradiation

Reduced graphene oxide (RGO)-TiO₂ nanocomposites have exhibited effective photocatalytic degradation of various organic pollutants. However, their poor solubility could limit their application in water and other organic solvents. In this study, new graphene-based cross-linked ethylenediaminetetraacetic acid (EDTA)-RGO-TiO₂ (ERGT) nanocomposites were synthesized for the removal of Cd(II) and photodegradation of phenol from wastewater by surface-functionalized cross-linking heavy metal chelating agent sodium edetate (EDTA) and photocatalyst titanium dioxide. The structural properties of fabricated nanocomposites were characterized using SEM, TEM, XPS, FTIR, XRD, UV-vis, gas sorption, and Raman spectroscopy analyses. Moreover, the adsorption of Cd(II) and the degradation of phenol under different conditions were studied. The experimental results revealed that the optimal catalytic degradation and adsorption performance could be achieved at pH 5.5, and the maximum absorption ratio of cadmium ions and the degradation efficiency of phenol can reach 178.2 mg/g and 90%, respectively. The results suggested that ERGT is a potential material for the removal of threatening pollutants from wastewater.

Photocatalytic ozonation in water treatment: Is there really a synergy between systems?

Numerous studies report on the synergy between ozonation and photocatalytic oxidation (TiO₂/UVA), which could open the way to the application of photocatalytic ozonation (PCOz) in water treatment. With the aim of establishing the existence of this synergy and its origin, in this work, using TiO₂ P25, 365 nm UVA LEDs and ozone transferred doses up to 5 mg (mg DOC₀)^-1 (DOC₀ 7 - 10 mg L^-1), a systematic study has been carried out featuring the effect of pH, alkalinity and water matrix in each of the systems involved in PCOz, with special attention to the role of organics adsorption onto TiO₂. In ultrapure water, an increase in pH and carbonates content exerted a slight negative effect on the photocatalytic degradation of primidone (low adsorption onto TiO₂ and mainly abated by free HO^•), this effect being higher on its mineralization. The negative effect of pH and alkalinity was much stronger for oxalic acid (high tendency to adsorb and mainly oxidized by positive holes). Accordingly, the results obtained at pH < pH_pzc (point of zero charge of the catalyst) in ultrapure water cannot at all be extrapolated to secondary effluents, since their composition negatively affects the photocatalytic performance. At the experimental conditions applied, only for the secondary effluent a synergy between O₃/UVA and TiO₂/UVA systems was observed. This synergy would be related, on the one hand, to the generation, from the matrix itself, of reactive entities or intermediates that promote the decomposition of ozone into HO^•; and, on the other hand, to an increase in catalyst activity as the matrix UVA absorption decreases, rather than from direct interactions between both systems. Despite de above, ozone requirement to achieve a significant reduction of DOC is high and would only be an interesting strategy for the elimination of ozone-refractory micropollutants.

The role of antibiotics and heavy metals on the development, promotion, and dissemination of antimicrobial resistance in drinking water biofilms

Antimicrobial resistance (AMR), as well as the development of biofilms in drinking water distribution systems (DWDSs), have become an increasing concern for public health and management. As bulk water travels from source to tap, it may accumulate contaminants of emerging concern (CECs) such as antibiotics and heavy metals. When these CECs and other selective pressures, such as disinfection, pipe material, temperature, pH, and nutrient availability interact with planktonic cells and, consequently, DWDS biofilms, AMR is promoted. The purpose of this review is to highlight the mechanisms by which AMR develops and is disseminated within DWDS biofilms. First, this review will lay a foundation by describing how DWDS biofilms form, as well as their basic intrinsic and acquired resistance mechanisms. Next, the selective pressures that further induce AMR in DWDS biofilms will be elaborated. Then, the pressures by which antibiotic and heavy metal CECs accumulate in DWDS biofilms, their individual resistance mechanisms, and co-selection are described and discussed. Finally, the known human health risks and current management strategies to mitigate AMR in DWDSs will be presented. Overall, this review provides critical connections between several biotic and abiotic factors that influence and induce AMR in DWDS biofilms. Implications are made regarding the importance of monitoring and managing the development, promotion, and dissemination of AMR in DWDS biofilms.

A review of ecotoxicity reduction in contaminated waters by heterogeneous photocatalytic ozonation

The widespread deterioration of our water systems requires new wastewater treatment technologies to ensure environmental protection. Conventional wastewater treatments were not designed for, and are therefore ineffective, at removing contaminants of emerging concern (CECs) such as pharmaceuticals, personal care products, pesticides, and industrial chemicals. Furthermore, treatment processes capable of breaking down CECs may produce toxic transformation products more harmful than the parent chemicals. Heterogeneous photocatalytic ozonation provides a promising option with high degradation and mineralization of organic compounds. The aim of the present paper is to review ecotoxicity reduction in water treated by heterogeneous photocatalytic ozonation as a measure of process viability. The discussion investigates changes in toxicity based on a variety of toxicity tests performed to evaluate potential effects on ecosystems, the types of catalysts and radiation sources used, the nature of the target contaminants, and the type of water matrix treated. Acute toxicity testing, TiO₂ catalysts, and mercury-vapour lamps including blacklights were dominant in the reviewed studies, investigated in 86%, 84% and 79% of the papers, respectively. Pharmaceuticals were the main group of chemicals treated and the water matrices used were predominantly pure water and secondary effluent. Overall, the findings of these studies provide evidence that photocatalytic ozonation is an efficient process to remove persistent organic compounds while, most of the time, not increasing the toxicity of the effluent (as reported by 86% of the studies). Due to the wide variation in experimental set-ups, no clear correlation between reaction conditions and toxicity was determined, however, V. fischeri acute toxicity assays and chronic/sublethal tests appeared most sensitive to transformation products. Future studies need to a) incorporate multiple toxicity tests to produce a more reliable and inclusive ecotoxicity assessment of treated effluent and b) investigate immobilized catalysts and energy efficient radiation sources (i.e. solar and LEDs) for industrial applications.

Recent developments in physical, biological, chemical, and hybrid treatment techniques for removing emerging contaminants from wastewater

Emerging contaminants (ECs) in wastewater have recently attracted the attention of researchers as they pose significant risks to human health and wildlife. This paper presents the state-of-art technologies used to remove ECs from wastewater through a comprehensive review. It also highlights the challenges faced by existing EC removal technologies in wastewater treatment plants and provides future research directions. Many treatment technologies like biological, chemical, and physical approaches have been advanced for removing various ECs. However, currently, no individual technology can effectively remove ECs, whereas hybrid systems have often been found to be more efficient. A hybrid technique of ozonation accompanied by activated carbon was found significantly effective in removing some ECs, particularly pharmaceuticals and pesticides. Despite the lack of extensive research, nanotechnology may be a promising approach as nanomaterial incorporated technologies have shown potential in removing different contaminants from wastewater. Nevertheless, most existing technologies are highly energy and resource-intensive as well as costly to maintain and operate. Besides, most proposed advanced treatment technologies are yet to be evaluated for large-scale practicality. Complemented with techno-economic feasibility studies of the treatment techniques, comprehensive research and development are therefore necessary to achieve a full and effective removal of ECs by wastewater treatment plants.

Rethinking water treatment targets: Bacteria regrowth under unprovable conditions

Ozonation is among the currently used technologies to remove chemical and biological contaminants from secondary treated urban wastewater (UWW). Despite its effectiveness on the abatement of organic micropollutants (OMPs) and disinfection, previous studies have shown that regrow of bacteria may occur upon storage of the ozonated UWW. This reactivation has been attributed to the high content of assimilable organic carbon after treatment. In order to investigate if ozonation by-products are the main biological regrowth drivers in stored ozonated UWW, the ozonation surviving cells were resuspended in sterile bottled mineral water (MW), simulating a pristine oligotrophic environment. After 7 days storage, organisms such as Acinetobacter, Methylobacterium, Cupriavidus, Massilia, Acidovorax and Pseudomonas were dominant in both ozonated UWW and pristine MW, demonstrating that bacterial regrowth is not strictly related to the eventual presence of ozonation by-products, but instead with the ability of the surviving cells to cope with nutrient-poor environments. The resistome of UWW before and after ozonation was analysed by metagenomic techniques. Draft metagenome assembled genomes (dMAGs), recovered from both ozonated UWW and after cell resuspension in MW, harboured genes conferring resistance to diverse antibiotics classes. Some of these antibiotic resistance genes (ARGs) were located in the vicinity of mobile genetic elements, suggesting their potential to be mobilized. Among these, dMAGs affiliated to taxa with high relative abundance in stored water, such as P. aeruginosa and Acinetobacter spp., harboured ARGs conferring resistance to 12 and 4 families of antibiotics, respectively, including those encoding carbapenem hydrolysing oxacillinases. The results herein obtained point out that the design and development of new wastewater treatment technologies should include measures to attenuate the imbalance of the bacterial communities promoted by storage of the final treated wastewater, even when applying processes with high mineralization rates.

Effect of preferential UV photolysis on the source control of antibiotic resistome during subsequent biological treatment systems

The environmental spread of antibiotic resistance genes (ARGs) from the direct application of traditional biological treatment systems for antibiotics in water is a potential public health threat. UV photolysis has been proved to be an efficient pretreatment method for antibacterial activity elimination, but the fate of antibiotic resistome in subsequent bioreactors fed with pretreated florfenicol (FLO) in synthetic wastewater is still unknown. Antibacterial activity in synthetic wastewater was effectively eliminated by UV irradiation pretreatment, and the diversity and abundance of detected ARGs in both aerobic and anaerobic bioreactors were significantly lower than those without pretreatment. Meanwhile, UV irradiation pretreatment shaped the structure and composition of sludge microbial communities in the subsequent bioreactors closer to those of the FLO-free groups. The relative abundances of Pseudomonas and Escherichia-Shigella working as the potential hosts of ARGs were significantly reduced in aerobic and anaerobic bioreactors, respectively. The significantly positive correlation between floR and intI1 and the decrease of intI1 abundance in UV photolytic pretreatment groups indicated that the horizontal transfer of floR was decreased. The study provides new insights into the effect of preferential UV photolysis as a pretreatment method on the source control of antibiotic resistome in subsequent biological treatment process.

Removal of tetracycline-resistant Escherichia coli and its genes through ultrasound treatment combined with ultraviolet light emitting diodes

Antibiotic resistance has gained increasing attention worldwide, and wastewater treatment plants have been regarded as hotspots for antibiotic-resistant bacteria and antibiotic-resistant genes (ARGs). In this study, we evaluated the removal of tetracycline-resistant Escherichia coli and its related genes through ultrasound (US) treatment with different input levels of US-specific energy combined with ultraviolet light emitting diodes (UV-LEDs). Simultaneous US with UV-LEDs effectively eliminated tetracycline-resistant E. coli with the normal suggested UV-LEDs dosage (below 30 mJ/cm²). The removal efficiency increased with the addition of US (specific input energy of 8-16 kJ/L), and simultaneous US treatment with UV-LEDs was relatively more effective than US pretreatment. Analyses of cell damage by K⁺ leakage and flow cytometry showed that the cell wall kept its integrity during the applied treatment conditions. Consequently, the removal efficiencies of 16 S rRNA, tet M, and tet Q were unsatisfactory because less than 1 log reduction was achieved. Increasing the US energy remarkably damaged the cell wall and potentially promoted the reaction. The removal of ARGs increased four times when using US-specific input energy at 330 kJ/L with 5 mJ/cm² compared with UV-LEDs alone. The US treatment combined with UV-LEDs is a novel process that does not require chemicals. Results of this research can provide theoretical support for the removal of ARGs.

Regrowth of bacteria after light-based disinfection - What we know and where we go from here

Regrowth of bacteria after water/wastewater disinfection is a serious risk to public health, particularly when such pathogens carry antibiotic resistance genes. Despite increasing interest in light-based disinfection using ultraviolet or solar radiation, the mechanism of bacterial regrowth and their concentration upon light exposure (i.e., during storage, or after discharge into rivers or lakes) remain poorly understood. Therefore, we present a focused critical review to 1) elucidate regrowth mechanisms, 2) summarize the pros and cons of available experimental designs and detection techniques for regrowth evaluation, and 3) provide an outlook of key research directions for further investigations of post-disinfection bacterial regrowth. Bacterial regrowth can occur through reactivation from a viable but non-culturable state, repair of photo-induced DNA damage, and reproduction of bacteria surviving disinfection. Many studies have underestimated the degree of actual regrowth because of the use of simple experimental designs and plate count methods, which cannot quantify actual abundance of viable bacteria. Further research should investigate the effects of various factors on bacterial regrowth in realistic conditions in regrowth tests and adopt multiplex detection methods that combine culture-based and culture-independent approaches. An accurate understanding of the mechanisms involved in bacterial regrowth following disinfection is critical for safeguarding public health and aquatic environments.