Dissolved organic matter adsorption from surface waters by granular composites versus granular activated carbon columns: An applicable approach

From effluent to fertilizer: Phosphorus recovery and reuse using granulated iron-oxyhydroxide-montmorillonite composites

Recovering phosphorus (P) from wastewater offers a sustainable solution to managing the anthropogenic P cycle by reducing water pollution and enhancing its use efficiency in agriculture. This study developed a P recovery platform using montmorillonite‑iron-oxyhydroxide composites (FeOx-MMT) granulated with a polycation. The adsorption properties of the granules were compared to a commercially available granulated ferric hydroxide (GFH) and the powdered FeOx-MMT. Then, the spent material (P-loaded FeOx-MMT granules) was tested as a P-fertilizer in comparison to triple-super-phosphate, a commercial fertilizer. Batch adsorption tests showed that GFH had a higher maximum adsorption capacity than FeOx-MMT granules (10 mg∙P∙g-1 vs 3.6 mg∙P∙g-1), yet this trend is reversed when normalized to iron content (32.4 mg∙P∙g-Fe-1 vs 61 mg∙P∙g-Fe-1). In addition, the adsorption of P to FeOx-MMT granules was significantly faster than GFH. In terms of desorption, the FeOx-MMT granules showed higher ability compared to GFH. Consequently, in column experiments with real secondary effluent these trends translated to higher overall removal efficiencies by the FeOx-MMT granules: FeOx-MMT specifically adsorbed phosphate ions while leaving other anions like sulfate, nitrate, and chloride in solution. Positively charged ions such as Ca2+, Mg2+ and NH4+, were also removed by the granulated FeOx-MMT. The result was high volumes of effluent with P concentrations below 0.1 ppm (regulation limit), and granulated composites loaded with high concentrations of P and essential cations. The bioavailability of P from the spent granules in soil was then tested in funnel and tomato-pot experiments. The results suggest that the adsorbed P is released in a manner that can support growth of agricultural crops. This approach supports sustainable phosphorus management, preserving resources, reducing pollution, and promoting food security while enhancing ecological and economic health.

CO2-Responsive Smart Wood Scaffold for Natural Organic Matter Removal without Secondary Pollution

Ensuring drinking water safety remains a critical challenge, particularly when treating complex water sources, due to secondary pollution caused by active chemical additives. Herein, a novel CO2-responsive smart wood scaffold that leverages non-toxic CO2 activation is developed to achieve highly efficient removal of carcinogenic natural organic matter (NOM) and broad-spectrum microbial disinfection without requiring additional chemical agents. Unlike conventional water purification techniques that face a safety-efficacy trade-off, the multi-stage CO2-responsive wood scaffold offers exceptional tunability in NOM abatement across diverse environmental conditions, including variable water chemistry, NOM composition, high salinity, and real-world water sources. The purified water meets stringent drinking water standards (e.g., UV254 reduction, dissolved organic carbon removal, and bacterial elimination). It is found that the highly efficient NOM adsorption mainly originates from the strong and stable CO2-triggered cation-π interaction between the scaffold surface and aromatic NOM groups, as revealed via high-resolution mass spectrometry and direct intermolecular force measurements. This ecofriendly and contamination-free CO2-responsive strategy provides a transformative approach to overcoming secondary pollution challenges in water purification, offering a scalable and sustainable platform for environmental applications and beyond.

Adsorption of Methyl Red on Poly(diallyldimethylammonium) Chloride-Modified Clay

A novel, eco-friendly and cost-effective adsorbent, poly(diallyldimethylammonium) chloride (PDADMAC)-modified clay was developed to enhance its efficacy in removing Methyl Red (MR) from water. Different concentrations of PDADMAC solutions were evaluated during the synthesis and the effects of different operating conditions were investigated. The kinetic data closely followed the pseudo-first-order model, while equilibrium data were well described by Freundlich isotherm. MR removal efficiency decreased as solution pH or NaCl concentration increased, suggesting that electrostatic interaction plays a key role in the adsorption process. Regeneration studies using NaCl solutions revealed that a 1% NaCl solution effectively restored the adsorbent's capacity. The findings indicate that PDADMAC clay is a promising and sustainable adsorbent for MR removal. Additionally, a three-layer backpropagation artificial neural network (ANN) was developed to predict the MR removal efficiency based on the initial MR concentration, pH, NaCl concentration, and adsorption time. Among these variables, pH was identified as the most influential factor. This approach provides valuable insight into the outcome prediction of a given adsorption process.

Water residence time is an important predictor of dissolved organic matter composition and drinking water treatability

Freshwater ecosystems are critical resources for drinking water. In recent decades, dissolved organic matter (DOM) inputs into aquatic systems have increased significantly, particularly in central and northern Europe, due to climatic and anthropogenic drivers. The associated increase in dissolved organic carbon (DOC) concentration can change lake ecosystem services and adversely affect drinking water treatment processes. In this study, we examined spatial and temporal patterns of DOM treatability with granular activated carbon (GAC) and biological reactivity based on 14-day bacterial respiration incubations at 11 sites across Mälaren during six-time points between July 2019 and February 2021. Mälaren is the third largest lake in Sweden and provides drinking water for over 2 million people including the capital city Stockholm. In our spatio-temporal analysis, we assessed the influence of phytoplankton abundance, water chemistry, runoff, and climate on DOM composition, GAC removal efficiency, and biological reactivity. Variations in DOM composition were characterized using optical measurements and Orbitrap mass spectrometry. Multivariate statistical analyses indicated that DOM produced during warmer months was easier to remove by GAC. Removal efficiency of GAC varied from 41 to 87 %, and the best predictor of treatability using mass spectrometry was double bond equivalents (DBE), while the best optical predictors were specific UV absorbance (SUVA), and freshness index. The oxygen consumption rate (k) from the bacterial respiration incubations ranged from 0.04 to 0.71 d-1 and higher in warmer months and at deeper basins and was associated with more aliphatic and fresh DOM. The three deepest lake basins with the longest water residence time (WRT) were temporally the most stable in terms of DOM composition and had the highest DOC removal efficiency and k rates. DOM composition in these three lake basins was optically clearer than in basins located closer to terrestrial inputs and had a signature suggesting it was derived from in-lake processes including phytoplankton production and bacterial processing of terrestrial DOM. This means that with increasing WRT, DOM derived from terrestrial sources shifts to more aquatically produced DOM and becomes easier to remove with GAC. These findings indicate WRT can be highly relevant in shaping DOM composition and thereby likely to affect its ease of treatability for drinking water purposes.

Recovery of organic matters by activated sludge from municipal wastewater: Performance and characterization

Municipal wastewater treatment processes consume a significant amount of energy and generate substantial carbon emissions. However, organic matters existing in municipal wastewater hold the potential as a valuable carbon source. Activated sludge has the potential to capture and recover the organic matters, thereby enriching carbon sources and facilitating subsequent sludge anaerobic digestion as well as in line with the concept of sustainable development. Based on above, this study investigated the enrichment and recovery characteristics and mechanisms of activated sludge adsorption on carbon sources in municipal wastewater, while optimizing the recovery conditions. The results indicated that insoluble organic matters, as well as a fraction of dissolved organic matters, can be effective recovered within approximately 40 min. Specifically, 74.1% of insoluble organic matters and 25.8% of soluble organic matters were successfully captured by the activated sludge, resulting in a 5.0% increase in sludge organic matter content. Moreover, activated sludge demonstrated remarkable recovery of particulate organic matters across various particle sizes, particularly larger particles (>5 μm) with high protein content. Notably, the dissolved biodegradable organics such as tryptophan and tyrosine protein-like substances according to 3D-EEM and lipids, proteins/amino sugars, and carbohydrates according to FT-ICR MS can be effectively recovered. Finally, the study revealed that the recovery of organic matters from the wastewater by activated sludge followed the pseudo-second-order kinetics model, with surface binding, hydrogen bonding and interparticle diffusion in sludge flocs as the primary adsorption mechanisms. This approach had abroad application prospects for improving the profitability of wastewater treatment plants.

Quantitative structure-activity relationships for the reaction kinetics of trace organic contaminants with one-electron oxidants

Understanding the reactivity between trace organic contaminants (TrOCs) and radicals involved in advanced oxidation processes (AOPs) is necessary for a good process design, but the experimentally determined rate constants (k values) are not sufficient for numerous artificial TrOCs. Thus, the development of quantitative structure-activity relationships (QSARs) for predicting k values may be an effective way to address this limitation. In this work, we developed QSARs for the reactions of TrOCs with AOP-related one-electron oxidants. Specifically, 15 QSARs using Hammett constants and 8 cross-correlations were developed based on the k values of over 400 reactions between TrOCs (most contain electron-rich moieties, such as phenol, aniline, and alkoxy benzene) and 5 one-electron oxidants (SO4˙-, Br˙, Br2˙-, Cl2˙-, and CO3˙-). Overall, the developed QSARs show a good predictive performance with 94% (237/251, for Hammett constant-based QSARs) and 80% (218/274, for cross-correlations) of the k values predicted within a factor of 3. All the Hammett constant-based QSARs show negative slope values and all cross-correlations show positive relationships, suggesting all 5 one-electron oxidants mainly share similar electrophilic mechanisms with the TrOCs highlighted in this work. Previous QSAR studies on the k values of one-electron oxidants were compared and integrated into their model analysis. Furthermore, k values predicted herein from the QSARs were used to evaluate the degradation of TrOCs during UV/persulfate and UV/chlorine treatment in multiple wastewater matrices, which were demonstrated to be useful. Finally, remarks on the use of the developed QSARs were presented.

Synthesis of cellulose cotton-based UiO-66 MOFs for the removal of rhodamine B and Pb(II) metal ions from contaminated wastewater

The presence of pollutants in drinking water has become a significant concern recently. Various substances, including activated carbon, membranes, biochar, etc., are used to remove these pollutants. In the present study, a new composite comprising cotton fabric and a mixture of Metal-Organic Frameworks (MOFs) was synthesized and used as an adsorbent for eliminating pollutants from wastewater. At first, the UiO-66 MOFs were prepared by a simple method of reacting Zirconium (IV) chloride (ZrCl4) and p-Phthalic acid (PTA) after successful preparation of UiO-66 then modified its surface with amino functional groups by reacting with APTES to obtain UiO-66-NH2. Moreover, the cellulose cotton fabric (CF) surface was modified with Polydopamine (PDA) and obtained CF@PDA. Further, with the help of EDC-HCl and NHS, the UiO-66-NH2 grafted on the surface of the CF@PDA and finally obtained CF@PDA/UiO-66-NH2. In addition, the adsorption study was performed toward RhB dye and Pb(II) metal ion pollutants. The maximum adsorption toward RhB dye was 68.5 mg/g, while toward Pb(II) metal ions was 65 mg/g. In addition, the kinetic study was also conducted and the result favoured the Pseudo-second order kinetic study. The adsorption isotherm was also studied and the Langmuir model was more fitted as compared with the Freundlich model. Moreover, the material has excellent regeneration and recycling ability after ten cycles. The significant adsorption ability, the novel combination of cotton and MOFs, and the recycling feature make our material CF@PDA/UiO-66-NH2 a promising potential absorbent material for wastewater treatment and even in other important areas of water research.

Granular activated carbon enhances volatile fatty acid production in the anaerobic fermentation of garden wastes

Garden waste, one type of lignocellulosic biomass, holds significant potential for the production of volatile fatty acids (VFAs) through anaerobic fermentation. However, the hydrolysis efficiency of garden waste is limited by the inherent recalcitrance, which further influences VFA production. Granular activated carbon (GAC) could promote hydrolysis and acidogenesis efficiency during anaerobic fermentation. This study developed a strategy to use GAC to enhance the anaerobic fermentation of garden waste without any complex pretreatments and extra enzymes. The results showed that GAC addition could improve VFA production, especially acetate, and reach the maximum total VFA yield of 191.55 mg/g VSadded, which increased by 27.35% compared to the control group. The highest VFA/sCOD value of 70.01% was attained in the GAC-amended group, whereas the control group only reached 49.35%, indicating a better hydrolysis and acidogenesis capacity attributed to the addition of GAC. Microbial community results revealed that GAC addition promoted the enrichment of Caproiciproducens and Clostridium, which are crucial for anaerobic VFA production. In addition, only the GAC-amended group showed the presence of Sphaerochaeta and Oscillibacter genera, which are associated with electron transfer processes. Metagenomics analysis indicated that GAC addition improved the abundance of glycoside hydrolases (GHs) and key functional enzymes related to hydrolysis and acidogenesis. Furthermore, the assessment of major genera influencing functional genes in both groups indicated that Sphaerochaeta, Clostridium, and Caproicibacter were the primary contributors to upregulated genes. These findings underscored the significance of employing GAC to enhance the anaerobic fermentation of garden waste, offering a promising approach for sustainable biomass conversion and VFA production.

Trichloramine and Hydroxyl Radical Contributions to Dichloroacetonitrile Formation Following Breakpoint Chlorination

Breakpoint chlorination is applied to remove ammonia in water treatment. Trichloramine (NCl₃) and transient reactive species can be present, but how they affect the formation of nitrogenous disinfection byproducts is unknown. In this study, the dichloroacetonitrile (DCAN) formation mechanisms and pathways involved during breakpoint chlorination (i.e., free chlorine to ammonia molar ratio ≥2.0) were investigated. DCAN formation during breakpoint chlorination of natural organic matter (NOM) isolates was 14.3-20.3 μg/L, which was 2-10 times that in chlorination without ammonia at similar free chlorine residual conditions (2.1-2.9 mg/L as Cl₂). The probe tests and electron paramagnetic resonance spectra supported the presence of ^•OH, ^•NO, and NCl₃ besides free chlorine in breakpoint chlorination. ¹⁵N-labeled ammonium-N tests indicated the incorporation of ammonium-N in DCAN formation though ammonia was eliminated during breakpoint chlorination. Aromatic non-nitrogenous moieties, such as phenols (i.e., none DCAN precursors in the free-chlorine-only system), became DCAN precursors during breakpoint chlorination. The reactions involved in reactive nitrogen species, such as ^•NO/^•NO₂ and NCl₃, led to additional nitrogen sources in DCAN formation, accounting for 36-84% of total nitrogen sources in DCAN formation from NOM isolates and real water samples. Scavenging ^•OH by tert-butanol reduced DCAN formation by 40-56%, indicating an important role of ^•OH in transforming DCAN precursors. This study improves the understanding of breakpoint chlorination chemistry.

Uptake Mechanisms of a Novel, Activated Carbon-Based Equilibrium Passive Sampler for Estimating Porewater Methylmercury

We describe the validation of a novel polymeric equilibrium passive sampler comprised of agarose gel with embedded activated carbon particles (ag+AC), to estimate aqueous monomethylmercury (MeHg) concentrations. Sampler behavior was tested using a combination of idealized media and realistic sediment microcosms. Isotherm bottle experiments with ag+AC polymers were conducted to constrain partitioning to these materials by various environmentally relevant species of MeHg bound to dissolved organic matter (MeHgDOM) across a range of sizes and character. Log of partitioning coefficients for passive samplers (Kps ) ranged from 1.98 ± 0.09 for MeHg bound to Suwannee River humic acid to 3.15 ± 0.05 for MeHg complexed with Upper Mississippi River natural organic matter. Reversible equilibrium exchange of environmentally relevant MeHg species was demonstrated through a series of dual isotope-labeled exchange experiments. Isotopically labeled MeHgDOM species approached equilibrium in the samplers over 14 days, while mass balance was maintained, providing strong evidence that the ag+AC polymer material is capable of equilibrium measurements of environmentally relevant MeHg species within a reasonable deployment time frame. Samplers deployed across the sediment-water interface of sediment microcosms estimated both overlying water and porewater MeHg concentrations within a factor of 2 to 4 of measured values, based on the average measured Kps values for species of MeHg bound to natural organic matter in the isotherm experiments. Taken together, our results indicate that ag+AC polymers, used as equilibrium samplers, can provide accurate MeHg estimations across many site chemistries, with a simple back-calculation based on a standardized Kps. Environ Toxicol Chem 2022;41:2052-2064. © 2022 SETAC.

Adsorptive removal of propranolol under fixed-bed column using magnetic tyre char: Effects of wastewater effluent organic matter and ball milling

We investigated the competitive effects of different fractions of wastewater treatment plant effluent organic matter (EfOM) on adsorption of an organic micro pollutant (OMP), propranolol (PRO), in a fixed bed column packed with magnetic tyre char (MTC). The results showed that the presence of EfOM inhibited PRO adsorption in wastewater leading to decreased PRO adsorption capacity from 5.86 to 2.03 mg/g due to competitive effects and pore blockage by smaller EfOM fractions. Characterization of EfOM using size exclusion chromatography (LC-OCD) showed that the principal factor controlling EfOM adsorption was pore size distribution. Low molecular weight neutrals had the highest adsorption onto MTC while humic substances were the least interfering fraction. Effect of important parameters such as contact time, linear velocity and bed height/diameter ratio on MTC performance was studied in large-lab scale columns. Linear velocity and contact time were found to be effective in increasing adsorption capacity of PRO on MTC and delaying breakthrough time. Increase in linear velocity from 0.64 cm/min to 1.29 cm/min increased mass transfer and dispersion, resulting in considerable rise of adsorbed amount (5.86 mg/g to 22.58 mg/g) and increase in breakthrough time (15.8-62.7 h). Efficiency of non-equilibrium Hydrus model considering dispersion and mass transfer mechanism was demonstrated for real wastewater and scale up purposes. Ball milling for degradation of adsorbed PRO and regeneration of MTC resulted in 79% degradation of PRO was achieved after 5 h milling (550 rpm), while the addition of quartz sand increased the efficiency to 92%.

Improving reverse osmosis concentrate treatment and nutrients conversion to Chlorella vulgaris bioenergy assisted with granular activated carbon

Landfill leachate (LL), especially the reverse osmosis concentrate (ROC), is a societal burden due to high toxicity but may have intrinsic values attributing to copious nutrients and organics. ROC bioremediation by microalgae has attracted much attentions benefiting from its extra advantage of bioenergy production. However, efficient microalgae cultivation with ROC is still a challenging task attributing to notorious ROC characteristics, like high chromaticity and toxicity. To alleviate these negative influences, a technique integrating granular activated carbon (GAC) pretreatment and microalgae bioremediation was proposed, with which nitrogen and phosphorus removal efficiencies achieved 100% along with an optimized microalgal biomass concentration of 1.44 g/L and lipid yield of 482.4 mg/L. Furthermore, a total volumetric energy yield of 33.6 kJ/L was acquired, which was conducive to realize energy valorization. The visualization evidence of three-dimensional fluorescence spectroscopy revealed chromaticity degradation mechanism of ROC as humic acids reduction and transfer to family of soluble microbial by-products. Meanwhile, contributions of GAC adsorption and microalgae assimilation on nutrients removal were analyzed. Together, this work provides a promising method and valuable information for ROC bioremediation with microalgae.

Reactive oxygen species formation in thiols solution mediated by pyrogenic carbon under aerobic conditions

Previous studies have demonstrated that pyrogenic carbon can mediate the reductive degradation of pollutants in solutions containing reducing reagents under anaerobic conditions. However, few studies have investigated oxidative species formation and pollutants transformation directly mediated by pyrogenic carbon under aerobic conditions. In this study, we found that activated carbon (AC) can not only mediate reductive hexachloroethane degradation in the absence of O₂ but also mediate the oxidation of As(III) and sulfanilamide in L-Cysteine (Cys, a naturally abundant thiol compound) solution under aerobic conditions. Electron paramagnetic resonance and quenching studies indicated that O₂^•-, H₂O₂ and ^•OH was formed in Cys/AC system under aerobic conditions. High O₂ content favored the formation of ^•OH, indicating that O₂ participated in ^•OH production. In addition, an increase in AC concentration and specific surface area led to increased formation of ^•OH, and other pyrogenic carbon materials such as biochar and graphite were also found capable of mediating the formation of ^•OH. This study demonstrates that pyrogenic carbon could mediate ^•OH formation in solutions containing reductive reagents under aerobic conditions, which provides a new perspective for studying the behavior of pyrogenic carbon in the environment and its role in biogeochemical processes.

Evaluation of Sand Filtration and Activated Carbon Adsorption for the Post-Treatment of a Secondary Biologically-Treated Fungicide-Containing Wastewater from Fruit-Packing Industries

In this work, a sand filtration-activated carbon adsorption system was evaluated to remove the fungicide content of a biologically treated effluent. The purification process was mainly carried out in the activated carbon column, while sand filtration slightly contributed to the improvement of the pollutant parameters. The tertiary treatment system, which operated under the batch mode for 25 bed volumes, resulted in total and soluble COD removal efficiencies of 76.5 ± 1.5% and 88.2 ± 1.3%, respectively, detecting total COD concentrations below 50 mg/L in the permeate of the activated carbon column. A significant pH increase and a respective electrical conductivity (EC) decrease also occurred after activated carbon adsorption. The total and ammonium nitrogen significantly decreased, with determined concentrations of 2.44 ± 0.02 mg/L and 0.93 ± 0.19 mg/L, respectively, in the activated carbon permeate. Despite that, the initial imazalil concentration was greater than that of the fludioxonil in the biologically treated effluent (i.e., 41.26 ± 0.04 mg/L versus 7.35 ± 0.43 mg/L, respectively). The imazalil was completely removed after activated carbon adsorption, while a residual concentration of fludioxonil was detected. Activated carbon treatment significantly detoxified the biologically treated fungicide-containing effluent, increasing the germination index by 47% in the undiluted wastewater or by 68% after 1:1 v/v dilution.

Insights into the adsorption mechanism of tannic acid by a green synthesized nano-hydroxyapatite and its effect on aqueous Cu(II) removal

The polyphenolic tannic acid (TA) has been widely used in the stabilization and surface modification of nanomaterials. The interaction mechanism of TA with the biogenic nano-hydroxyapatite (nHAP) and its environmental importance, however, are poorly understood. This study explored the adsorption of TA using the green synthesized, eggshell-derived nHAP and implications of this process for the removal of aqueous Cu(II) via batch adsorption experiments, Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS) investigations. TA adsorption by nHAP was a complex pH-dependent process and significantly correlated with TA molecule speciation and amphoteric properties of nHAP via multiple adsorption modes including surface complexation, electrostatic attraction, and hydrogen bond. The maximum TA adsorption amount was found to be 94.8 mg/g for less crystalline nHAP with lower calcination temperature. In the ternary Cu-TA-nHAP systems, TA promoted Cu(II) adsorption at pH < 5 and reduced Cu(II) uptake at pH > 5. Further studies of the effects of ionic strength and addition sequences, as well as Raman, FTIR, and XPS analyses revealed Cu(II) adsorption on nHAP was mainly dominated by inner-sphere surface complexation. These results can shed light on not only the utility of biogenic nHAP for TA and Cu(II) adsorption but also the evaluation of the effect of TA on the environmental behavior of heavy metals.

Reactivity of Chlorine Radicals (Cl• and Cl2•-) with Dissolved Organic Matter and the Formation of Chlorinated Byproducts

Chlorine radicals, including Cl^• and Cl₂^•-, can be produced in sunlight waters (rivers, oceans, and lakes) or water treatment processes (e.g., electrochemical and advanced oxidation processes). Dissolved organic matter (DOM) is a major reactant with, or a scavenger of, Cl^• and Cl₂^•- in water, but limited quantitative information exists regarding the influence of DOM structure on its reactivity with Cl^• and Cl₂^•-. This study aimed at quantifying the reaction rates and the formation of chlorinated organic byproducts produced from Cl^• and Cl₂^•- reactions with DOM. Laser flash photolysis experiments were conducted to quantify the second-order reaction rate constants of 19 DOM isolates with Cl^• (k_DOM-Cl•) and Cl₂^•- (k_DOM-Cl2•-), and compare those with the hydroxyl radical rate constants (k_DOM-•OH). The values for k_DOM-Cl• ((3.71 ± 0.34) × 10⁸ to (1.52 ± 1.56) × 10⁹ M_C^-1 s^-1) were orders of magnitude greater than the k_DOM-Cl2•- values ((4.60 ± 0.90) × 10⁶ to (3.57 ± 0.53) × 10⁷ M_C^-1 s^-1). k_DOM-Cl• negatively correlated with the weight-averaged molecular weight (M_W) due to the diffusion-controlled reactions. DOM with high aromaticity and total antioxidant capacity tended to react faster with Cl₂^•-. During the same experiments, we also monitored the formation of chlorinated byproducts through the evolution of total organic chlorine (TOCl) as a function of chlorine radical oxidant exposure (CT value). Maximum TOCl occurred at a CT of 4-8 × 10^-12 M·s for Cl^• and 1.1-2.2 × 10^-10 M·s for Cl₂^•-. These results signify the importance of DOM in scavenging chlorine radicals and the potential risks of producing chlorinated byproducts of unknown toxicity.

Designing clay-polymer nanocomposite sorbents for water treatment: A review and meta-analysis of the past decade

Clay-polymer nanocomposites (CPNs) have been studied for two decades as sorbents for water pollutants, but their applicability remains limited. Our aim in this review is to present the latest progress in CPN research using a meta-analysis approach and identify key steps necessary to bridge the gap between basic research and CPN application. Based on results extracted from 99 research articles on CPNs and 8 review articles on other widely studies sorbents, CPNs had higher adsorption capacities for several inorganic and organic pollutant classes (including heavy metals, oxyanions, and dyes, n = 308 observations). We applied principal component analysis, analysis of variance, and multiple linear regressions to test how CPN and pollutant properties correlated with Langmuir adsorption model coefficients. While adsorption was, surprisingly, not influenced by mineral properties, it was influenced by CPN fabrication method, polymer functional groups, and pollutant properties. For example, among the pollutant classes, heavy metals had the highest adsorption capacity but the lowest adsorption affinity. On the other hand, dyes had high adsorption affinities, as reflected by the linear correlation between adsorption affinity and pollutant molecular weight. Scaling from 'basic research' to 'technological application' requires testing CPN performance in real water, application in columns, comparison to commercial sorbents, regeneration, and cost evaluation. However, our survey indicates that of the 158 observations, only 20 compared the CPN's performance to that of a commercial sorbent. We anticipate that this review will promote the design of smart and functional CPNs, which can then evolve into an effective water treatment technology.