Efficient decontamination of organic pollutants under high salinity conditions by a nonradical peroxymonosulfate activation system

Comparative study on the activation of peroxymonosulfate and peroxydisulfate by Ar plasma-etching CNTs for sulfamethoxazole degradation: Efficiency and mechanisms

Sulfamethoxazole (SMX), a widely utilized antibiotic, was continually detected in the environment, causing serious risks to aquatic ecology and water security. In this study, carbon nanotubes (CNTs) with abundant defects were developed by argon plasma-etching technology to enhance the activation of persulfate (PS, including peroxymonosulfate (PMS) and peroxydisulfate (PDS)) for SMX degradation while reducing environmental toxicity. Obviously, the increase of ID/IG value from 0.980 to 1.333 indicated that Ar plasma-etching successfully introduced rich defects into CNTs. Of note, Ar-90-CNT, whose Ar plasma-etching time was 90 min with optimum catalytic performance, exhibited a significant discrepancy between PMS activation and PDS activation. Interestingly, though the Ar-90-CNT/PDS system (kobs = 0.0332 min-1) was more efficient in SMX elimination than the Ar-90-CNT/PMS system (kobs = 0.0190 min-1), Ar plasma-etching treatment had no discernible enhancement in the catalytic efficiency of MWCNT for PDS activation. Then the discrepancy on activation mechanism between PMS and PDS was methodically investigated through quenching experiments, electron spin resonance (ESR), chemical probes, electrochemical measurements and theoretical calculations, and the findings unraveled that the created vacancy defects were the ruling active sites for the production of dominated singlet oxygen (1O2) in the Ar-90-CNT/PMS system to degrade SMX, while the electron transfer pathway (ETP), originated from PDS activation by the inherent edge defects, was the central pathway for SMX removal in the Ar-90-CNT/PDS system. Based on the toxicity test of Microcystis aeruginosa, the Ar-90-CNT/PDS system was more effective in alleviating environmental toxicity during SMX degradation. These findings not only provide insights into the discrepancy between PMS activation and PDS activation via carbon-based materials with controlled defects regulated by the plasma-etching strategy, but also efficiently degrade sulfonamide antibiotics and reduce the toxicity of their products.

Efficient roxarsone degradation by low-dose peroxymonosulfate with the activation of recycling iron-base composite material: Critical role of electron transfer

Pollutant degradation via electron transfer based on advanced oxidation processes (AOPs) provides an economical and energy-efficient method for pollution control. In this study, an iron-rich waste, heating pad waste (HPW), was recycled as a raw material, and a strong magnetic catalyst (Fe-HPW) was synthesized at high temperature (900 °C). Results showed that in the constructed Fe-HPW/PMS system, effective roxarsone (ROX) degradation and TOC removal (72.54%) were achieved at a low-dose of oxidant (PMS, 0.05 mM) and catalyst (Fe-HPW, 0.05 g L-1), the ratio of PMS to ROX was only 2.5:1. In addition, the released inorganic arsenic was effectively removed from the solution. The analysis of the experimental results showed that ROX was effectively degraded by forming PMS/catalyst surface complexes (Fe-HPW-PMS*) to mediate electron transfer in the Fe-HPW/PMS system. Besides, this system performed effective ROX degradation over a wide pH range (pH=3-9) and showed high resistance to different water parameters. Overall, this study not only provides a new direction for the recycling application of HPW but also re-emphasizes the neglected nonradical pathway in advanced oxidation processes.

The Unique Fe3Mo3N Structure Bestowed Efficient Fenton-Like Performance of the Iron-Based Catalysts: The Double Enhancement of Radicals and Nonradicals

Iron-based catalysts are widely used in Fenton-like water pollution control technology due to their high efficiency, but their practical applications are limited by complex preparation conditions and strong blockage of Fe2+/Fe3+ cycle during the reaction. Here, a new iron-molybdenum bimetallic carbon-based catalyst is designed and synthesized using cellulose hydrogel for adsorption of Fe and Mo bimetals as a template, and the effective iron cycle in water treatment is realized. The integrated materials (Fe2.5Mo@CNs) with "catalytic/cocatalytic" performance have higher Fenton-like activation properties and universality than the equivalent quantity iron-carbon-based composite catalysts (Fe@CNs). Through the different characterization methods, experimental verifications and theoretical calculations show that the unique Fe3Mo3N structure promotes the adsorption of persulfate and reduces the energy barrier of the reaction, further completing the double enhancement of radicals (such as SO4·-) and nonradicals (1O2 and electron transport process). The integrated "catalytic/cocatalytic" combined material is expected to provide a new promotion strategy for Fenton-like water pollution control.

2D/2D heterojunctions for rapid and self-cleaning removal of antibiotics via visible light-assisted peroxymonosulfate activation: Efficiency, synergistic effects, and applications

Developing eco-friendly and efficient technologies for treating antibiotic wastewater is crucial. Traditional methods face challenges in incomplete removal, high costs, and secondary pollution. Heterogeneous peroxymonosulfate (PMS) activation assisted by visible light shows promise, but suitable activators remain a huge challenge. Here, we synthesized cost-effective carbon nitride/bismuth bromide oxide (CN/BiOBr) heterojunctions. Such a heterojunction achieved rapid PMS activation, achieving over 90.00% tetracycline (TC) removal only within 1 min (kobs of 2.23 min-1), surpassing previous systems by nearly 1-2 orders of magnitude and even remarkably superior to the popular single-atom catalysts. The system exhibited self-cleaning properties, maintaining activity after 8 cycles and stability across a wide pH range (3.01 to 9.03). Quenching experiments and theoretical calculations elucidated the exclusive •O2- species involvement and removal pathways. Eco-toxicity assessment and total organic carbon results confirmed simultaneous degradation, detoxification, and mineralization. This system also showed excellent resistance to environmental factors, e.g., coexisting anions, varying pH, and water sources, and demonstrated potential in coking and medical wastewater purification. This study presents a novel technique for rapidly decontaminating antibiotic wastewater through visible light-assisted PMS activation and introduces innovative bionic catalytic oxidation combining light and darkness for practical applications.

Tannic acid-assisted upcycling of Cu from waste printed circuit boards to an efficient peroxymonosulfate catalyst for the degradation of organic pollutants

The recovery of metals from solid waste for use as heterogeneous catalysts to activate peroxymonosulfate (PMS) for organic wastewater treatment is a promising, environmentally friendly and economical strategy. Herein, we present a facile and versatile strategy for upcycling copper (Cu) from waste printed circuit boards (PCBs) to Cu oxides supported on a three-dimensional carbon framework (10PCBs-Cu-TA) with the aid of tannic acid (TA). Compared to the PCBs-Cu synthesized without TA, introducing TA into 10PCBs-Cu-TA reduced Cu leaching, enhanced crystallinity, promoted electron transfer, and increased the number of oxygen vacancies. Moreover, 10PCBs-Cu-TA exhibited superior catalytic activity in activating PMS for the degradation of reactive brilliant blue KN-R, exceeding the activity of 10Cu-TA prepared using commercial Cu(NO3)2·3H2O. This enhanced performance may be attributed to the higher specific surface area and oxygen vacancies of 10PCBs-Cu-TA. The 10PCBs-Cu-TA/PMS system also exhibited broad catalytic universality and adaptability to various contaminants and water matrices. Quenching experiments, electron paramagnetic resonance analysis, and electrochemical measurements indicated that radical and non-radical processes jointly contributed to KN-R degradation. The proposed strategy for upcycling Cu from waste PCBs into functional materials provides novel insights into the utilization of solid waste and the development of PMS activators.

A novel nano-cerium oxide functionalized biochar composite for degradation of organic dye: insight of the photocatalysis mechanism

Recently, visible-light-driven photocatalysis attracts much concerns in the remediation of environmental organic pollutants. In this study, the cerium doped biochar was fabricated through the hydrothermal method, and served as an efficient photocatalyst towards rhodamine B degradation under visible light irradiation. Almost 100% of rhodamine B was removed by 2.0 g·L-1 cerium doped biochar after 60 min of visible light irradiation at pH 3, but only about 25.50% and 29.60% of rhodamine B was removed by cerium dioxide and biochar under identical conditions. The degradation process coincided well with the pseudo-first-order kinetic model, and the photodegradation rate constant of cerium doped biochar was 0.0485·min-1, which was respectively 97 and 44 times that of biochar (0.0005·min-1) and cerium dioxide (0.0011·min-1). According to the trapping experiments and electron spin resonance spectroscopy analysis, h+, O2-∙ and ∙OH all participated in the degradation of rhodamine B in the cerium doped biochar photocatalytic systems, and the function of h+ and ∙OH was dominated. Consequently, the biochar could not only be an excellent carrier for supporting cerium dioxide, but also greatly improved its photocatalytic activity. The band gap of cerium doped biochar was narrower than cerium dioxide, which could improve the separation and migration of photogenerated electron-hole pairs under visible-light excitation, thus ultimately enhanced the degradation of rhodamine B. This work provided a deeper understanding of the preparation of biochar-based photocatalyst and its application in the remediation of environmental organic pollution.

Paint sludge derived activated carbon encapsulating with cobalt nanoparticles for non-radical activation of peroxymonosulfate

Industrial solid waste management and recycling are important to environmental sustainability. In this study, cobalt (Co) nanoparticles encapsulated in paint sludge-derived activated carbon (AC) were fabricated. The Co-AC possessed high conductivity, magnetic properties and abundant metal oxide impurities (TiAlSiOx), which was applied as multifunctional catalyst for peroxymonosulfate (PMS) activation. Compared to pure AC, the Co-AC exhibited significant enhanced performance for degradation of tetracycline hydrochloride (TCH) via PMS activation. Mechanism studies by in situ Raman spectroscopy, Fourier infrared spectroscopy, electrochemical analysis and electron paramagnetic resonance suggested that surface-bonded PMS (PMS*) and singlet oxygen (1O2) are the dominant reactive species for TCH oxidation. The non-radical species can efficiently oxidize electron-rich pollutants with high efficiency, which minimized the consumption of PMS and the catalyst. The removal percentages of TCH reached 97 % within 5 min and ∼ 99 % within 15 min in the Co-AC/PMS system. The Co active sites facilitated PMS adsorption to form the PMS* and the TiAlSiOx impurities provided abundant oxygen vacancy for generation of the 1O2. In addition, the Co-AC/PMS system achieved high efficiency and stability for oxidation of the target pollutants over a long-term continuous operation. This work not only offers a cost-effective approach for recycling industrial waste but also provides new insights into the application of waste-derived catalyst for environmental remediation.

Revealing the synergistic effect between radical and non-radical species of sulfur-doped carbon nitride for ciprofloxacin removal: Based on density functional theory study

The distinct characteristics of active species produced during the photocatalytic reaction can result in alterations in the degradation routes of organic pollutants with diverse chemical structures. The relationship between the active species and degradation pathways of organic pollutants lacks a direct experimental or characterization method, so in-depth research is still needed to understand the details of their interactions. In this study, sulfur-doped bulk carbon nitride (SBCN) was prepared based on bulk carbon nitride (BCN), and the process of S-doping enhancing the production of O21 was revealed. Through the degradation experiment, the degradation rate of CIP by SBCN reached 91 %, which was higher than that of BCN (66 %). The increase of degradation rate was mainly attributed to the increase of O21. Through the density functional theory (DFT) calculation of CIP and its degradation intermediate, due to the preferential oxidation of CIP by O21, O21 changes the initial degradation direction of CIP, releasing more attack sites for ˙O2-, thereby achieving more efficient degradation of CIP through the synergy of O21 and ˙O2-. In this study, the attack preferences of the active species and their synergistic promotion provide important insights for the efficient photocatalytic degradation of organic pollutants.

Selective formation of high-valent iron in Fenton-like system for emerging contaminants degradation under near-neutral and high-salt conditions

In view of the near-neutral and high-salt conditions, the Fenton technology with hydroxyl radicals (HO•) as the main reactive species is difficult to satisfy the removal of trace emerging contaminants (ECs) in pharmaceutical sewage. Here, a layered double hydroxide FeZn-LDH was prepared, and the selective formation of ≡Fe(IV)=O in Fenton-like system was accomplished by the chemical environment regulation of the iron sites and the pH control of the microregion. The introduced zinc can increase the length of Fe-O bond in the FeZn-LDH shell layer by 0.22 Å compared to that in Fe2O3, which was conducive to the oxygen transfer process between ≡Fe(III) and H2O2, resulting in the ≡Fe(IV)=O formation. Besides, the amphoteric hydroxide Zn(OH)2 can regulate the pH of the FeZn-LDH surface microregion, maintaining reaction pH at around 6.5-7.5, which could avoid the quenching of ≡Fe(IV)=O by H+. On the other hand, owing to the anti-interference of ≡Fe(IV)=O and the near-zero Zeta potential on the FeZn-LDH surface, the trace ECs can also be effectively degraded under high-salt conditions. Consequently, the process of ≡Fe(IV)=O generation in FeZn-LDH system can satisfy the efficient removal of ECs under near-neutral and high-salt conditions.

Efficient carbamazepine degradation by modified copper tailings and PMS system: Performance evaluation and mechanism

It is a green and sustainable path to establish cheap solid waste-based catalyst to establish peroxymonosulfate (PMS) catalytic system for the degradation of carbamazepine (CBZ) in water. In this study, durable copper tailing waste residue-based catalyst (CSWR) was prepared, and efficient CSWR/PMS system was constructed for catalytic degradation of CBZ for first time. The morphology and structure of CSWR changed from clumps to porous and loose amorphous by alkali leaching and medium temperature calcination. The reconstructed surface of the CSWR exposes more active sites promotes the catalytic reaction and increases the degradation rate of CBZ by more than 39.8 times. And the CSWR/PMS achieved a CBZ removal of nearly 99.99 % in 20 min. In particular, perovskite-type iron-calcium compounds were formed, which stimulated the production of more HO• and SO4•- in the system. DFT calculation shows that CSWR has stronger adsorption energy and electron transfer ability to PMS molecules, which improved the degradation efficiency of the system. In general, this study proposed a means of high-value waste utilization, which provided a new idea for the preparation of solid waste based environmental functional materials and is expected to be widely used in practical wastewater treatment.

Plastic wastes-derived N-doped carbon nanotubes for efficient removal of sulfamethoxazole in high salinity wastewater via nonradical peroxymonosulfate activation

Peroxymonosulfate (PMS) catalytic activation is effective to eliminate organic pollutants from water, thus the development of low-cost and efficient catalysts is significant in applications. The resource conversion of plastic wastes (PWs) into carbon nanotubes (CNTs) is a promising candidate for PMS-based advanced oxidation processes (AOPs), and also a sustainable strategy to realize plastic management and reutilization. Herein, cost-effective PWs-derived N-doped CNTs (N-pCNTs) were synthesized, which displayed efficient activity for PMS activation through an electron transfer pathway (ETP) for sulfamethoxazole (SMX) degradation in high salinity water. The pyrrolic N induced the positively charged surface of N-pCNTs, favoring the electrostatic adsorption of PMS and subsequent generation of active PMS* . A galvanic oxidation process was developed to prove the electron-shuttle dominated ETP for SMX oxidation. Combined with theoretical calculations, the efficiency of ETP was determined by the potential difference between HOMO of SMX and LUMO of N-pCNTs. Such oxidation produced low-toxicity intermediates and resulted in selective degradation of specific sulfonamide antibiotics. This work reveals the feasibility of low-cost N-pCNTs catalysts from PWs serving as an appealing candidate for PMS-AOPs in water remediation, providing a new solution to alleviate environmental issues caused by PWs and also advances the understanding of ETP during PMS activation.

Regulating electronic structure of Fe single-atom site by S/N dual-coordination for efficient Fenton-like catalysis

The activity of single-atom catalysts in peroxymonosulfate activation process is bound up with the local electronic state of metal center. However, the large electronegativity of N atoms in Metal-N4 restricts the electron transfer between center metal atom and peroxymonosulfate. Herein, we constructed Fe-SN-C catalyst by incorporating S atom in the first coordination sphere of Fe single-atom site (Fe-S1N3) for Fenton-like catalysis. The Fe-SN-C with a low valent Fe is found to exhibit excellent catalytic activity for bisphenol A degradation, and the corresponding rate constant reaches 0.405 min-1, 11.9-fold higher than the original Fe-N-C. Besides, the Fe-SN-C/PMS system exhibits ideal catalytic stability under the effect of wide pH range and background substrates by the fast generation of high-valent Fe species. Experimental results and theoretical calculations reveal that the dual coordination of S and N atoms notably increases the local electron density of Fe atoms and electron filling in eg orbital, causing a d band center shifting close to the fermi level and thereby optimizes the activation energy for peroxymonosulfate decomposition via Fe 3d-O 2p orbital interaction. This work provides further development of promising SACs for the efficient activation of peroxymonosulfate based on direct regulation of the coordination environment of active center metal atoms.

Synergistic effect of Fe doping and oxygen vacancy in AgIO3 for effectively degrading organic pollutants under natural sunlight

In this work, a series of hydrogenated Fe-doped AgIO3 (FAI-x) catalysts are synthesized for photodegrading diverse azo dyes and antibiotics. Under the irradiation of natural sunlight with a light intensity of ∼60 mW/cm2, the optimum FAI-10 exhibits a considerable rate constant for decomposing methyl orange (MO) of 0.067 min-1, about 7.4 times higher than that of AgIO3 (0.009 min-1), and 24.6% and 83.8% of MO can be decomposed over AgIO3 and FAI-10 after irradiation for 40 min. In the amplification photodegradation experiments with using 0.5 g catalyst and 400 mL MO dye solution (10 mg/L), FAI-10 possesses greatly higher photoreactivity to common semiconductors (ZnO, TiO2, In2O3 and Bi2MoO6), and the photodegradation rates over FAI-10 are 92%. Particularly, the FAI-10 shows superior stability, the activity of which remains unaltered after 8 continuous cycles. Foreign ions and water bodies have slight effect on the activity of FAI-10, but the MO degradation rates are decreased by adjusting pH values, especially when pH = 11 because of the strong electrostatic repulsion between MO and FAI-10. FAI-10 can also effectively decompose another azo dye (rhodamine B (RhB)) and diverse antibiotics (sulflsoxazole (SOX), chlortetracycline hydrochloride (CTC), tetracycline hydrochloride (TC) and ofloxacin (OFX)). The activity enhancement mechanism of FAI-10 has been systemically investigated and is ascribed to the promoted photo-absorption, charge separation and transfer efficiency, and affinity of organic pollutants, owing to the synergistic effect of Fe doping and oxygen vacancy (Ov). The photocatalytic mechanisms and process for decomposing MO are verified and proposed based on radical trapping experiments and liquid chromatography-mass spectrometry (LC-MS). This work opens an avenue for the fabrication of effective photocatalysts toward water purification.

Insights into enhanced oxidation of benzophenone-type UV filters (BPs) by ferrate(VI)/ferrihydrite: Increased conversion of Fe(VI) to Fe(V)/Fe(IV)

In this work, the oxidation performance of a new ferrate(VI)/ferrihydrite (Fe(VI)/Fh) system was systematically explored to degrade efficiently six kinds of benzophenone-type UV filters (BPs). Fe(VI)/Fh system not only had a superior degradation capacity towards different BPs, but also exhibited higher reactivity over a pH range of 6.0-9.0. The second-order kinetic model successfully described the process of BP-4 degradation by heterogeneous Fh catalyzed Fe(VI) system (R2 = 0.93), and the presence of Fh could increase the BP-4 degradation rate by Fe(VI) by an order of magnitude (198 M-1·s-1 v.s. 14.2 M-1·s-1). Remarkably, there are higher utilization efficiency and potential of Fe(VI) in Fe(VI)/Fh system than in Fe(VI) alone system. Moreover, characterization and recycling experiments demonstrated that Fh achieved certain long-term running performance, and the residual Fe content of solution after clarifying process meet World Health Organization (WHO) guidelines for drinking water. The contributions of reactive species could be ranked as Fe(V)/Fe(IV) > Fe(VI) > •OH. Fe(IV)/Fe(V) were the dominant species for the enhanced removal in the Fe(VI)/Fh system, whose percentage contribution (72 %-36 %) were much higher than those in Fe(VI) alone system (5 %-17 %). However, the contribution of Fe(VI) in oxidizing BP-4 should not be underestimated (20 %-56 %). These findings reasonably exploit available Fh resources to reduce the relatively high cost of Fe(VI), which offers a proper strategies for efficient utilization of high-valent iron species and may be used as a highly-efficient and cost-effective BPs purification method.

Embedding electronic perpetual motion into single-atom catalysts for persistent Fenton-like reactions

In our quest to leverage the capabilities of the emerging single-atom catalysts (SACs) for wastewater purification, we confronted fundamental challenges related to electron scarcity and instability. Through meticulous theoretical calculations, we identified optimal placements for nitrogen vacancies (Nv) and iron (Fe) single-atom sites, uncovering a dual-site approach that significantly amplified visible-light absorption and charge transfer dynamics. Informed by these computational insights, we cleverly integrated Nv into the catalyst design to boost electron density around iron atoms, yielding a potent and flexible photoactivator for benign peracetic acid. This exceptional catalyst exhibited remarkable stability and effectively degraded various organic contaminants over 20 cycles with self-cleaning properties. Specifically, the Nv sites captured electrons, enabling their swift transfer to adjacent Fe sites under visible light irradiation. This mechanism accelerated the reduction of the formed "peracetic acid-catalyst" intermediate. Theoretical calculations were used to elucidate the synergistic interplay of dual mechanisms, illuminating increased adsorption and activation of reactive molecules. Furthermore, electron reduction pathways on the conduction band were elaborately explored, unveiling the production of reactive species that enhanced photocatalytic processes. A six-flux model and associated parameters were also applied to precisely optimize the photocatalytic process, providing invaluable insights for future photocatalyst design. Overall, this study offers a molecule-level insight into the rational design of robust SACs in a photo-Fenton-like system, with promising implications for wastewater treatment and other high-value applications.

Accelerated removal of naproxen in the iron-based peracetic acid activation system by chloride ions: Enhancement of reactive oxidative species via the formation of iron-chloride complexes

Iron-based PAA activation process is a promising advanced oxidation process for water decontamination which depends on Fe(II) as the main reactive site for PAA activation, resulting in various reactive oxidative species (ROSs) generation. For practical application, the impact of water matrix chloride ion (Cl-) on ROSs production and contaminants removal should be carefully considered. In this study, it's found that the introduction of Cl- (0.1-10 mM) could significantly enhance the reaction rate of the rapid stage (kobs1) up to 2.15 times at the initial pH of 4.25 in the Fe(II)/PAA system. Further studies demonstrated that the improved removal capacity of NAP resulted from Cl- induced R-O• generation as indicated by the exposure dose of R-O• increasing from 7.74 × 10-11 M•s to 1.44 × 10-10 M•s, rather than chlorine-containing radicals' generation. DFT calculation results suggested that the formed Fe(II)-Cl- complexes could easily activate PAA to generate more ROSs for NAP removal. Moreover, Fe(II)/PAA treatment can alleviate the biological toxicity of pollutants via both the Escherichia coli test and toxicity assessment. The obtained new knowledge manifested that Cl- can boost ROSs generation and conversion in iron-based PAA systems, providing guidance for the efficient decontamination of chlorine-containing sewage with PAA-based AOPs.

Enhanced TC degradation by persulfate activation with carbon-coated CuFe2O4: The radical and non-radical co-dominant mechanism, DFT calculations and toxicity evaluation

Facing the constraints of critical agglomeration and poor reusability of CuFe2O4 in catalytic applications, the feasibility of synthesizing a composite catalyst using carbon coating technology for efficient TC removal with enhanced PDS activity was investigated. The composite catalyst (CuFe2O4@C) can stimulate both radical (SO4•- and HO•) and non-radical (1O2) pathways to dominate the catalytic reaction for removing 95.7% of the TC in 60 min. Meanwhile, the defective structure of the external carbon layer protected the internal CuFe2O4 from excessive oxidation, allowing the CuFe2O4@C to maintain over 90% TC removal after 5 cycles with less interference from inorganic anions, demonstrating significant catalytic performance and satisfactory reusability. Finally, the DFT calculations and TEST evaluation were performed to discuss the structural properties of TC and its toxicity assessment during the whole degradation process, while three possible degradation pathways were proposed. Significantly, the carbon-coated composite catalysts of potential universal applicability for multi-pathway PDS activation offered an attractive new strategy for the effective degradation of antibiotic wastewater.

Enhanced peroxymonosulfate activation via heteroatomic doping defects of pyridinic and pyrrolic N in 2D N‑doped carbon nanosheets for BPA degradation

Understanding the role of intrinsic defects and nonmetallic heteroatom doping defects in activating peroxymonosulfate (PMS) and subsequently degrading endocrine-disrupting compounds is crucial for designing more efficient carbon catalysts. Therefore, we synthesized N-rich carbon nanosheets (NCs) through pyrolysis of a glutamic acid and melamine mixture and utilized them to activate PMS for bisphenol A (BPA) degradation. Different weight ratios of the above mixtures were allowed for manipulating NCs' defect level and N configuration. The reaction rate constant (k) was significantly positively correlated with the pyridinic and pyrrolic N content, and negatively and weakly positively correlated with graphite N and intrinsic defects, respectively. These findings suggest pyridinic and pyrrolic N, rather than graphitic N and intrinsic defects, enhance PMS activation to generate reactive oxygen species (specifically O•-2 and 1O2) and oxidize BPA. The NC-activated PMS system with the highest N content (17.9 atom%) demonstrated a remarkably high k (0.127 min-1) using minimal concentrations of PMS (0.4 mM) and NC (0.15 g/L), highlighting the system's efficiency. Excess halide anions led to significantly increased k with only a limited formation of trichloromethane (disinfection byproducts) in presence of 100 mM Cl-. This study offers novel perspectives on identifying catalytic sites within N-doped carbonaceous materials.

Singlet oxygen-dominated peroxymonosulfate activation by layered crednerite for organic pollutants degradation in high salinity wastewater

Advanced oxidation processes have been widely studied for organic pollutants treatment in water, but the degradation performance of radical-dominated pathway was severely inhibited by the side reactions between the anions and radicals, especially in high salinity conditions. Here, a singlet oxygen (1O2)-dominated non-radical process was developed for organic pollutants degradation in high salinity wastewater, with layered crednerite (CuMnO2) as catalysts and peroxymonosulfate (PMS) as oxidant. Based on the experiments and density functional theory calculations, 1O2 was the dominating reactive species and the constructed Cu-O-Mn with electron-deficient Mn captured electron from PMS promoting the generation of 1O2. The rapid degradation of bisphenol A (BPA) was achieved by CuMnO2/PMS system, which was 5-fold and 21-fold higher than that in Mn2O3/PMS system and Cu2O/PMS system. The CuMnO2/PMS system shown prominent BPA removal performance under high salinity conditions, prominent PMS utilization efficiency, outstanding total organic carbon removal rate, wide range of applicable pH and good stability. This work unveiled that the 1O2-dominated non-radical process of CuMnO2/PMS system overcame the inhibitory effect of anions in high salinity conditions, which provided a promising technique to remove organic pollutants from high saline wastewater.

Enhancing sodium percarbonate catalytic wet peroxide oxidation with artificial intelligence-optimized swirl flow: Ni single atom sites on carbon nanotubes for improved reactivity and silicon resistance

H2O2 is widely used in the treatment of refractory organic pollutants.However, due to its explosive and corrosive chemical characteristics, H2O2 will bring great safety risks and troubles in transportation.So we chose sodium percarbonate(SPC) to be used in catalytic wet peroxide oxidation enhanced by swirl flow(SF-CWPO) and we designed carbon nanotubes with Ni single atom sites(Ni-NCNTs/AC) to activate SPC to treat an m-cresol wastewater containing Si.Meanwhile, artificial intelligence which used Artificial neural network (ANN) was used to optimize the conditions.Under the conditions of pH = 9.27, reaction time of 8.91 min, m-cresol concentration is 59.09 mg L-1, SPC dosage is 2.80 g L-1 and Na2SiO3·9H2O dosage is 77.27 mg L-1, the degradation rate of total organic carbon(TOC) and m-cresol reaches 94.37% and 100%, respectively.Finally, the applicability of Ni-NCNTs/AC-SPC-SF-CWPO technology was evaluated in a wastewater system of a sewage treatment enterprise and Fourier transform ion cyclotron resonance mass spectrum(FT-ICR MS) analysis and chemical oxygen demand(COD) analysis showed the great ability of Ni-NCNTs/AC-SPC-SF-CWPO technology to treat wastewater.It is believed that this paper is of great significance to the design and construction of the in-depth research and industrial application of SF-CWPO.

Interfacial Electron Transfer in Chemical and Biological Transformation of Pollutants in Environmental Catalysis

Interfacial electron transfer (IET) is essential for chemical and biological transformation of pollutants, operative across diverse lengths and time scales. This Perspective presents an array of multiscale molecular simulation methodologies, supplemented by in situ monitoring and imaging techniques, serving as robust tools to decode IET enhancement mechanisms such as interface molecular modification, catalyst coordination mode, and atomic composition regulation. In addition, three IET-based pollutant transformation systems, an electrocatalytic oxidation system, a bioelectrochemical spatial coupling system, and an enzyme-inspired electrocatalytic system, were developed, demonstrating a high effect in transforming and degrading pollutants. To improve the effectiveness and scalability of IET-based strategies, the refinement of these systems is necessitated through rigorous research and theoretical exploration, particularly in the context of practical wastewater treatment scenarios. Future endeavors aim to elucidate the synergy between biological and chemical modules, edit the environmental functional microorganisms, and harness machine learning for designing advanced environmental catalysts to boost efficiency. This Perspective highlights the powerful potential of IET-focused environmental remediation strategies, emphasizing the critical role of interdisciplinary research in addressing the urgent global challenge of water pollution.

Iron/nitrogen co-doped biochar derived from salvaged cyanobacterial for efficient peroxymonosulfate activation and ofloxacin degradation: Synergistic effect of Fe/N in non-radical path

A green, low-cost, high-performance Fe/N co-doped biochar material (Fe-N@C) was synthesized using salvaged cyanobacteria without other extra precursors for peroxymonosulfate (PMS) activation and ofloxacin (OFX) degradation. With the increased pyrolysis temperature, the graphitization degree, the specific surface area and the corresponding groups like OH, COO etc. for Fe-N@C tended to increase, resulting in a greater OFX adsorption. However, the total amount of Fe-NX and graphitic nitrogen groups in the Fe-N@C composites was firstly increased and then decreased, which reached the highest at 800 °C (Fe-N@C-800). All these changes of functional species ascribed to the strong interaction between Fe, N and C led to the highest defect degree of Fe-N@C-800, resulting the highest OFX removal efficiency of 95.0 %. OFX removal experiments indicated the adsorption process promoted the total OFX degradation for different functional groups on Fe-N@C composites separately dominated the process of OFX adsorption and PMS catalysis. Radical quenching and electron paramagnetic resonance (EPR) measurements proved free radical and non-free radical pathways participated in Fe-N@C/PMS system. The non-free radicals based on 1O2 and high-valent iron-oxo species played a more important role in OFX degradation, leading to the minimal effect of co-existing anions and the high universality for other antibiotic pollutants. Fe-NX was utilized as the main catalytic sites and graphitic nitrogen contributed more to the electron transfer for PMS activation, whose synergistic effect efficiently facilitated OFX degradation. Finally, the possible degradation route of OFX in the Fe-N@C-800/PMS system was proposed. All these results will provide the new insights into the intrinsic mechanism of Fe/N species in carbon-based materials for PMS activation.

O2 plasma-modified carbon nanotube for sulfamethoxazole degradation via peroxymonosulfate activation: Synergism of radical and non-radical pathways boosting water decontamination and detoxification

Sulfamethoxazole (SMX), a widely used antibiotic, has triggered increasing attention due to its extensive detection in wastewater effluent, causing serious ecological threats. Herein, a carbon-based heterogeneous catalyst was developed by the O2 plasma-etching process, regulating oxygen-containing functional groups (OFGs) and defects of carbon nanotubes (O-CNT) to activate peroxymonosulfate (PMS) for highly efficient SMX abatement. Through adjusting the etching time, the desired active sites (i.e., C=O and defects) could be rationally created. Experiments collectively suggested that the degradation of SMX was owing to the contribution of synergism by radical (•OH (17.3%) and SO4•- (39.3%)) and non-radical pathways (1O2, 43.4%), which originated from PMS catalyzed by C=O and defects. In addition, the possible degradation products and transformation pathways of SMX in the system were inferred by combining the Fukui function calculations and the LC-MS/MS analysis. And the possible degradation pathway was effective in reducing the environmental toxicity of SMX, as evidenced by the T.E.S.T. software and the micronucleus experiment on Vicia faba root tip. Also, the catalytic system exhibited excellent performance for different antibiotics removal, such as amoxicillin (AMX), carbamazepine (CBZ) and isopropylphenazone (PRP). This study is expected to provide an alternative strategy for antibiotics removal in water decontamination and detoxification.

Biochar-Based Single-Atom Catalyst with Fe-N3O-C Configuration for Efficient Degradation of Organic Dyes by Peroxymonosulfate Activation

Iron single-atom catalysts (Fe SACs) hold great promise for peroxymonosulfate (PMS) activation and degradation of organic pollutants in wastewater. However, insights into crucial catalytic sites and activation mechanisms of biochar-based Fe SACs for PMS remain a challenge. Herein, cotton stalk-derived biochar-based Fe SACs (Fe SACs-BC) with an asymmetric Fe-N/O-C configuration were prepared, and their PMS activation and acid orange 7 (AO7) degradation mechanisms were investigated. The results showed that the removal efficiency of the Fe SACs-BC catalyst with Fe-N3O-C configuration for AO7 and other five investigated organic dyes reached 95-99% within 15 min. The EPR spectrums, quenching experiments, electrochemical analysis, masking experiments, XPS, and theoretical calculations indicated that degradations of organic dyes were dominated by singlet oxygen, which was generated by direct PMS conversion at the electron-deficient carbon and iron sites in the Fe-N3O-C configuration. The Fe SACs-BC/PMS exhibited high removal efficiency and strong tolerance in different water matrices with a wide pH range, various coexisting anions and interfering substances, showing great potential and applicability for efficient treatment of actual textile wastewaters.

Constructing Hollow Multishelled Microreactors with a Nanoconfined Microenvironment for Ofloxacin Degradation through Peroxymonosulfate Activation: Evolution of High-Valence Cobalt-Oxo Species

This study constructed hollow multishelled microreactors with a nanoconfined microenvironment for degrading ofloxacin (OFX) through peroxymonosulfate (PMS) activation in Fenton-like advanced oxidation processes (AOPs), resulting in adequate contaminant mineralization. Among the microreactors, a triple-shelled Co-based hollow microsphere (TS-Co/HM) exhibited optimal performance; its OFX degradation rate was 0.598 min-1, which was higher than that of Co3O4 nanoparticles by 8.97-fold. The structural tuning of Co/HM promoted the formation of oxygen vacancies (VO), which then facilitated the evolution of high-valence cobalt-oxo (Co(IV)═O) and shifted the entire t2g orbital of the Co atom upward, promoting catalytic reactions. Co(IV)═O was identified using a phenylmethyl sulfoxide (PMSO) probe and in situ Raman spectroscopy, and theoretical calculations were conducted to identify the lower energy barrier for Co(IV)═O formation on the defect-rich catalyst. Furthermore, the TS-Co/HM catalyst exhibited remarkable stability in inorganic (Cl-, H2PO4-, and NO3-), organic (humic acid), real water samples (tap water, river water, and hospital water), and in a continuous flow system in a microreactor. The nanoconfined microenvironment could enrich reactants in the catalyst cavities, prolong the residence time of molecules, and increase the utilization efficiency of Co(IV)═O. This work describes an activation process involving Co(IV)═O for organic contaminants elimination. Our results may encourage the use of multishelled structures and inform the design of nanoconfined catalysts in AOPs.

Degradation of dimethyl phthalate by morphology controlled β-MnO2 activated peroxymonosulfate: The overlooked roles of high-valent manganese species

Activated peroxymonosulfate (PMS) processes have emerged as an efficient advanced oxidation process to eliminate refractory organic pollutants in water. This study synthesized a novel spherical manganese oxide catalyst (0.4KBr-β-MnO2) via a simple KBr-guided approach to activate PMS for degrading dimethyl phthalate (DMP). The 0.4KBr-β-MnO2/PMS system enhanced DMP degradation under different water quality conditions, exhibiting an ultrahigh and stable catalytic activity, outperforming equivalent quantities of pristine β-MnO2 by 8.5 times. Mn(V) was the dominant reactive species that was revealed by the generation of methyl phenyl sulfone from methyl phenyl sulfoxide oxidation. The selectivity of Mn(V) was demonstrated by the negligible inhibitory effects of Inorganic anions. Theoretical calculations confirmed that Mn (V) was more prone to attack the CO bond of the side chain of DMP. This study revealed the indispensable roles of high-valent manganese species in DMP degradation by the 0.4KBr-β-MnO2/PMS system. The findings could provide insight into effective PMS activation by Mn-based catalysts to efficiently degrade pollutants in water via the high-valent manganese species.

Construction of cubic CaTiO3 perovskite modified by highly-dispersed cobalt for efficient catalytic degradation of psychoactive pharmaceuticals

Sulfate radical mediated advanced oxidation processes (SR-AOPs) have emerged as a promising alternative for emerging contaminants degradation. However, high activity and great stability are commonly difficult to juggle, and the structure-activity correlations are still ambiguous. This study constructed the cubic CaTiO3 perovskite modified by highly-dispersed cobalt for peroxymonosulfate (PMS) activation to improve the specific lattice plane exposure and reduce the metal leaching simultaneously. 98% of amitriptyline (AMT) degradation was achieved within 60 min under the condition of 200 mg/L Co0.1-CTO and 100 mg/L PMS. The results indicated that surface Co2+/Co3+ redox couple and lattice oxygen were responsible for PMS activation, and the evolution of ·OH, SO4·- and 1O2 were revealed. According to density functional theory (DFT) calculations, the highly-dispersed Co on cubic surface effectively captured PMS and promoted electron transfer for the generation of ·OH and SO4·-, while more oxygen atoms exposed on Co0.1-CTO(200) surface facilitated the generation of 1O2. Briefly, this study provides a novel strategy of catalyst synthesis in PMS activation for water treatment.

Caffeic acid accelerated the Fe(II) reinvention in Fe(III)/PMS system for bisphenol A degradation: Oxidation intermediates and inherent mechanism

Fe(II)-catalyzed PMS process was widely used in the degradation of refractory pollutants in wastewater, while its performance was restricted by the slow regeneration efficiency of Fe(II). Herein, caffeic acid (CFA), a representative of hydroxycinnamic acids, was introduced into Fe(III)/PMS system to accelerate the transformation of Fe(III) to Fe(II) and promote the removal of bisphenol A (BPA). Under optimum condition of 0.1 mM CFA, 0.05 mM Fe(III), and 0.5 mM PMS, almost complete removal of BPA can be achieved within 20 min, which was roughly 6.2 times higher than that in Fe(III)/PMS system. As the addition of CFA into Fe(III)/PMS system, pH application range was widened from acidic to alkaline conditions. The reduction and chelation of CFA expedited the Fe(III)/Fe(II) cycle by forming CFA-Fe chelate, thereby facilitating the PMS activation. Based on LC-MS analysis and DFT calculation, the intermediate products of CFA were found to play a decisive role in boosting the regeneration of Fe(II), and the toxicity of these intermediates towards organisms was evaluated by ECOSAR. The alcohol-scavenging and chemical probe tests certified that hydroxyl radical (•OH), sulfate radical (SO4•-), and Fe(IV) coexisted in Fe(III)/CFA/PMS system, and the second-order reaction rate constants of •OH and SO4•- reacted with CFA were calculated to be 3.16✕109 and 2.30✕1010 M-1 s-1, respectively. Two major degradation pathways of BPA, •OH addition and SO4•- induced hydroxylation reaction, were proposed. This work presented a novel green phenolic compound that expedited the Fe(II)-catalyzed PMS activation process for the treatment of organic contaminants.

A sustainable solution for organic pollutant degradation: Novel polyethersulfone/carbon cloth/FeOCl composite membranes with electric field-assisted persulfate activation

Sulfate radical-based advanced oxidation processes (SR-AOP) and ultrafiltration (UF) membranes have demonstrated effectiveness in treating wastewater. This investigation illuminated a pioneering two-stage procedure for fabricating polyethersulfone/carbon cloth/FeOCl (PES/CC/FeOCl) composite catalytic membranes, exhibiting proficiency in persulfate activation. Evidenced by their distinctively high degradation rates and superior stability, these innovative composite membranes efficaciously obviate tetracycline (TC), showcasing a striking TC degradation rate, with an unparalleled removal ratio peaking at 93% under applied electrical fields. The process underlying persulfate activation and TC degradation was meticulously explored through electron paramagnetic resonance (EPR) and quenching trials. These evaluations unveil that hydroxyl radicals (•OH) and sulfate radicals (SO4•-) primarily drive the eradication of diminutive organic molecules. Subsequent studies emphasized the noteworthy rejection ratio of the PES/CC/FeOCl composite membranes (90%) for sodium alginate (SA), further revealing their exceptional on-line cleansing efficiency in an electrofiltration-associated in-situ oxidation system. In essence, this study proposed a novel approach for the synthesis of composite membranes adept at the catalytic degradation of organic pollutants. This paradigm-shifting research imparted a unique lens to perceive the integration of membrane separation technology, enriching the domain of advanced wastewater treatment strategies.

Piezoelectric-channels in MoS2-embedded polyvinylidene fluoride membrane to activate peroxymonosulfate in membrane filtration for wastewater reuse

The conjugation of membrane filtration (MF) with advanced oxidation process (AOPs) is being considered as an alternative advanced treatment process for the potable reuse of wastewater. Beyond conventional MF/AOPs conjugation, a new downstream MF process with piezoelectric-channels induced piezo-activated peroxymonosulfate (PMS) is herein constructed to deal with antiepileptic carbamazepine (CBZ) pollutants through polyvinylidene fluoride (PVDF) membrane (PVDF-M10). Through a MF process, ca. 93.8% CBZ pollutants can be removed under an ultrasonic-assisted piezo-activation PMS, whereas only 18.3% and 60.2% CBZ can be removed by using pure PVDF membrane under the same condition and PVDF-M10 membrane without ultrasonic-assisted piezo-activation. Even after 9-cycles, CBZ removal efficiency was maintained at 56.4% under this MF process. These superior performances are attributed to the piezoelectric exfoliated-MoS2 nanosheets (E-MoS2) embedded PVDF nanofibers in PVDF-M10 membrane, which lead to rich piezoelectric-channels in the membrane. These piezoelectric-channels not only produced more charges to activate PMS to boost the yield of reactive oxide species (ROS) but also provided an ideal platform for the rapid reaction between CBZ and ROS during MF process. This investigation develops a new MF technique to conjugate piezo-activation of PMS-AOPs for the efficient removal of emerging pollutants for the potable reuse of wastewater.

Insights into the carbon nanotubes-mediated activation of permanganate for decontamination under high salinity

Radical-based advanced oxidation process (AOPs) has attracted great interests in wastewater treatment field. However, by the traditional radical-based method, the degradation of organic pollution is greatly suppressed when radicals react with the co-existing anions in the solution. Herein, an efficient method for degrading of contaminant under high salinity conditions is discussed through a non-radical pathway. Carbon nanotubes (CNTs) was employed as an electron transfer medium to facilitate the electron conversion from contaminants to potassium permanganate (PM). Based the results of quenching experiments, probe experiments, and galvanic oxidation process experiments, the degradation mechanism of CNTs/PM process was demonstrated to be electron transfer, rather than reactive intermediate Mn species. As a result, typical influencing factors including salt concentration, cations, and humic acid have less of an impact on degradation during CNTs/PM processes. In addition, the CNTs/PM system exhibits superior reusability and universality of pollutants, which has the potential to be applied as a non-radical pathway for the purification of contaminant in the large-scale high salinity wastewater treatment.

Efficient carbamazepine degradation with Fe3+ doped 1T/2H hybrid molybdenum disulfide as peroxymonosulfate activator under high salinity wastewater

Drawing on the robust activation activity and affinity that transition metal ions and MoS₂ exhibit towards peroxymonosulfate (PMS), 1T/2H hybrid molybdenum disulfide doped with Fe³⁺ (Fe³⁺/N-MoS₂) was synthesized to activate PMS for the treatment of organic wastewater. The ultrathin sheet morphology and 1T/2H hybrid nature of Fe³⁺/N-MoS₂ were confirmed by characterization. The (Fe³⁺/N-MoS₂ + PMS) system demonstrated excellent performance in the degradation of carbamazepine (CBZ) above 90% within 10 min even under high salinity conditions. By electron paramagnetic resonance and active species scavenging experiments, it was inferred that SO₄^•─ palyed a dominant role in the treatment process. The strong synergistic interactions between 1T/2H MoS₂ and Fe³⁺ efficiently promoted PMS activation and generated active species. Additionally, the (Fe³⁺/N-MoS₂ + PMS) system was found to be capable of high activity for CBZ removal in high salinity natural water, and Fe³⁺/N-MoS₂ exhibited high stability during recycle tests. This new strategy of Fe³⁺ doped 1T/2H hybrid MoS₂ for more efficient PMS activation provides valuable insights for the removal of pollutants from high salinity wastewater.

Efficient removal of organic contaminants in CuS-mediated solid-liquid-interfacial fenton-like system: Role of bimetallic cycle and sulfur species

The conventional Fenton-like system (Fe(III)/H₂O₂) is severely limited by the inferior activity of Fe(III) on H₂O₂ activation to produce highly active species and the sluggish regeneration rate of Fe(II). This work significantly enhanced the oxidative breakdown of the target organic contaminant bisphenol A (BPA) by Fe(III)/H₂O₂ by introducing cheap CuS at a low dose of 50 mg/L. The BPA removal (20 mg/L) in CuS/Fe(III)/H₂O₂ system reached 89.5 % within 30 min under the optimal conditions: CuS dosage 50 mg/L, Fe(III) concentration 0.05 mM, H₂O₂ concentration 0.5 mM and pH 5.6. Compared to CuS/H₂O₂ and Fe(III)/H₂O₂ systems, the reaction constants had a 47- and 12.3-fold enhancement, respectively. Even compared with the conventional Fe(II)/H₂O₂ system, the kinetic constant also increased more than twice, further confirming the distinctive superiority of constructed system. Element species change analyses showed that Fe(III) in solution was adsorbed onto the CuS surface, and then Fe(III) was rapidly reduced by Cu(I) in the CuS lattice. Combining CuS and Fe(III) (in-situ formed CuS-Fe(III) composite) created a robust co-effect on the activation of H₂O₂. Also, S(-II) and its derivatives, e.g., S_n^2- and S⁰ (as an electron donor), could quickly reduce Cu(II) to Cu(I) and ultimately oxidize to the harmless product SO₄^2-. Notably, a mere 50 μM of Fe(III) was sufficient to maintain enough regenerated Fe(II) to effectively activate H₂O₂ in CuS/Fe(III)/H₂O₂ system. In addition, such a system achieved a broad range of pH applications and was more suitable for real wastewater containing anions and natural organic matter. Scavenging tests, electron paramagnetic resonance (EPR), and probes further verified the critical role of •OH. This work provides a new approach to solving the problems of Fenton systems through a solid-liquid-interfacial system design and exhibits considerable application potential in wastewater decontamination.

Asymmetrically Coordinated CoB1 N3 Moieties for Selective Generation of High-Valence Co-Oxo Species via Coupled Electron-Proton Transfer in Fenton-like Reactions

High-valence metal species generated in peroxymonosulfate (PMS)-based Fenton-like processes are promising candidates for selective degradation of contaminants in water, the formation of which necessitates the cleavage of OH and OO bonds as well as efficient electron transfer. However, the high dissociation energy of OH bond makes its cleavage quite challenging, largely hampering the selective generation of reactive oxygen species. Herein, an asymmetrical configuration characterized by a single cobalt atom coordinated with boron and nitrogen (CoB₁ N₃ ) is established to offer a strong local electric field, upon which the cleavage of OH bond is thermodynamically favored via a promoted coupled electron-proton transfer process, which serves an essential step to further allow OO bond cleavage and efficient electron transfer. Accordingly, the selective formation of Co(IV)O in a single-atom Co/PMS system enables highly efficient removal performance toward various organic pollutants. The proposed strategy also holds true in other heteroatom doping systems to configure asymmetric coordination, thus paving alternative pathways for specific reactive species conversion by rationalized design of catalysts at atomic level toward environmental applications and more.

The overlooked role of UV185 induced high-energy excited states in the dephosphorization of organophosphorus pesticide by VUV/persulfate

Vacuum ultraviolet (VUV) based advanced oxidation processes (AOPs) recently attracted widespread interests. However, the role of UV₁₈₅ in VUV is only considered to be generating a series of active species, while the effect of photoexcitation has long been overlooked. In this work, the role of UV₁₈₅ induced high-energy excited state for the dephosphorization of organophosphorus pesticides was studied using malathion as a model. Results showed malathion degradation was highly related to radical yield, while its dephosphorization was not. It was UV₁₈₅ rather than UV₂₅₄ or radical yield that was responsible for malathion dephosphorization by VUV/persulfate. DFT calculation results demonstrated that the polarity of P-S bond was further increased during UV₁₈₅ excitation, favoring dephosphorization while UV₂₅₄ did not. The conclusion was further supported by degradation path identification. Moreover, despite the fact that anions (Cl^-, SO₄^2- and NO₃^-) considerably affected radical yield, only Cl^- and NO₃^- with high molar extinction coefficient at 185 nm significantly affected dephosphorization. This study shed light on the crucial role of excited states in VUV based AOPs and provided a new idea for the development of mineralization technology of organophosphorus pesticides.

The debatable role of singlet oxygen in persulfate-based advanced oxidation processes

Singlet oxygen (¹O₂) attracts much attention in persulfate-based advanced oxidation processes (PS-AOPs), because of its wide pH tolerance and high selectivity toward electron-rich organics. However, there are conflicts about the ¹O₂ role in PS-AOPs on several aspects, including the formation of different key reactive oxygen species (ROS) at similar active sites, pH dependence, broad-spectrum activity, and selectivity in the elimination of organic pollutants. To a large degree, these conflicts root in the drawbacks of the methods to identify and evaluate the role of ¹O₂. For example, the quenchers of ¹O₂ have high reactivity to other ROS and persulfate as well. In addition, electron transfer process (ETP) also selectively oxidizes organics, having a misleading effect on the identification of ¹O₂. Therefore, in this review, we summarized and discussed some basic properties of ¹O₂, the debatable role of ¹O₂ in PS-AOPs on multiple aspects, and the methods and their drawbacks to identify and evaluate the role of ¹O₂. On the whole, this review aims to better understand the role of ¹O₂ in PS-AOPs and further help with its reasonable utilization.

Overlooked impacts of natural organic matter conversion in a Fe(II)-induced peroxymonosulfate activation system for river water remediation

The peroxymonosulfate (PMS) process may be hindered severely due to natural organic matter (NOM) conversion in the treatment of emerging pollutants from river water, becoming a critical engineering and technical issue. In this study, a Fe(II)-induced river water (RW)/PMS catalytic system was constructed for investigating molecular transformation of NOM and related influence mechanism to sulfamethoxazole (SMX) degradation. Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS) analysis indicated that NOM molecules containing no more than one heteroatom in river may be attacked by hydroxyl radicals (OH) and then polymerized, converting into molecules with two or three heteroatoms during PMS oxidation. Based on the correlation analysis, CHONP-NOM, CHOSP-NOM and CHONSP-NOM showed a significant inhibition against SMX degradation, while CHONS-NOM exhibited a moderate inhibitory effect. Besides, more condensed aromatic structures, carbohydrates and tannins were generated via reactive species (OH and sulfate radicals (SO₄^-)) oxidation, radical addition and polymerization reactions. Notably, condensed aromatic structures, carbohydrates and tannins presented weak, modest and strong inhibition to SMX degradation, respectively. Based on the current results, the inhibition of target pollutants degradation would be mitigated via regulation of NOM molecules in a Fe(II)-induced PMS activation system, providing valuable information to reduce NOM impact. In addition, this study paves the way to achieve efficient removal of emerging pollutants from river water.

Rapid activation of peroxymonosulfate with iron(Ⅲ) complex for organic pollutants degradation via a non-radical pathway

Developing high-performance catalytic systems for eliminating contaminants effectively in water has received a lot of attention. However, the complexity of practical wastewater poses a challenge for degrading organic pollutants. Non-radical active species with strong resistance to interference have shown great advantages in degrading organic pollutants under complex aqueous conditions. Herein, a novel system was constructed by Fe(dpa)Cl₂ (FeL, dpa = N, N'-(4-nitro-1,2-phenylene) dipicolinamide) activating peroxymonosulfate (PMS). The mechanism study verified that the FeL/PMS system had high efficiency in producing high-valent iron-oxo and singlet oxygen (¹O₂) to degrade various organic pollutants. In addition, the chemical bonding between PMS and FeL was elucidated by the density functional theory (DFT) calculations. The FeL/PMS system could remove 96% Reactive Red 195 (RR195) in 2 min, which was much higher than other systems involved in this study. More attractively, the FeL/PMS system demonstrated general resistance to interference from common anions (Cl^-, HCO₃^-, NO₃^- and SO₄^2-), humic acid (HA) and pH changes and were thus compatible with various natural waters. This work provides a new approach for producing non-radical active species, which is a promising catalytic system for water treatment.

Nanoconfinement-enhanced Fenton-like polymerization via hollow hetero-shell carbon for reducing carbon emissions in organic wastewater purification

Lower reaction speed and excessive oxidant inputs impede the removal of contaminants from water via the advanced oxidation processes based on peroxymonosulfate. Herein, we report a new confined catalysis paradigm via the hollow hetero-shell structured CN@C (H-CN@C), which permits effective decontamination through polymerization with faster reaction rates and lower oxidant dosage. The confined space structures regulated the CN and CO and electron density of the inner shell, which increased the electron transfer rate and mass transfer rate. As a result, CN in H-CN@C-10 reacted with peroxymonosulfate in preference to CO to generate singlet oxygen, improving the second-order reaction kinetics by 503 times. The identification of oxidation products implied that bisphenol AF could effectively remove by polymerization, which could reduce carbon dioxide emissions. These favorable properties make the nanoconfined catalytic polymerization of contaminants a remarkably promising nanocatalytic water purification technology.

New insights into engineering the core size and carbon shell thickness of Co@C core-shell catalysts for efficient and stable Fenton-like catalysis

Herein, we engineered the cobalt core size and carbon shell thickness of Co@C by molten salt electrolysis (MSE) to investigate the enhanced essence of decreasing core size as well as the shell thickness dependence-mediated transition of catalytic mechanisms. We found that the reaction activation energy (RAE) of Co@C/peroxymonosulfate (PMS) systems was intimately dependent on the core sizes for sulfamethoxazole (SMX) degradation. The smaller core size of 26 nm provided a lower RAE of 13.39 kJ mol^-1. In addition, increasing carbon shell thicknesses of Co@C altered the catalytic mechanisms from a radical pathway of SO₄^•- and •OH to to a non-radical pathway of ¹O₂ and electron-transfer process (ETP), which were verified by experimental results and density functional theory (DFT) calculations. Interestingly, increasing carbon shell thicknesses promoted the charge transfer between Co metal slab and carbon shell, increased the adsorption energy of PMS molecule on the Co@C slab, and decreased the length of OO, which favoured the occurrence of non-free radical processes.

Catalyst-Free Photochemical Activation of Peroxymonosulfate in Xanthene-Rich Systems for Fenton-Like Synergistic Decontamination: Efficacy of Proton Transfer Process

Catalyst-free visible light assisted Fenton-like catalysis offers opportunities to achieve the sustainable water decontamination, but the synergistic decontamination mechanisms are still unclear, especially the effect of proton transfer process (PTP). The conversion of peroxymonosulfate (PMS) in photosensitive dye-enriched system was detailed. The photo-electron transfer between excited dye and PMS triggered the efficient activation of PMS and enhanced the production of reactive species. Photochemistry behavior analysis and DFT calculations revealed that PTP was the crucial factor to determine the decontamination performance, leading to the transformation of dye molecules. The excitation process inducing activation of whole system was composed of low energy excitations, and the electrons and holes were almost contributed by LUMO and HOMO. This work provided new ideas for the design of catalyst-free sustainable system for efficient decontamination.

Enhanced Interfacial Electron Transfer by Asymmetric Cu-Ov -In Sites on In2 O3 for Efficient Peroxymonosulfate Activation

Enhancing the peroxymonosulfate (PMS) activation efficiency to generate more radicals is vital to promote the Fenton-like reaction activity, however, how to promote the PMS adsorption and accelerate the interfacial electron transfer to boost its activation kinetics remains a great challenge. Herein, we prepared Cu-doped defect-rich In₂ O₃ (Cu-In₂ O₃ /O_v ) catalysts containing asymmetric Cu-O_v -In sites for PMS activation in water purification. The intrinsic catalytic activity is that the side-on adsorption configuration of the O-O bond (Cu-O-O-In) at the Cu-O_v -In sites significantly stretches the O-O bond length. Meanwhile, the Cu-O_v -In sites increase the electron density near the Fermi energy level, promoting more and faster electron transfer to the O-O bond for generating more SO₄ ⋅^- and ⋅OH. The degradation rate constant of tetracycline achieved by Cu-In₂ O₃ /O_v is 31.8 times faster than In₂ O₃ /O_v , and it shows the possibility of membrane reactor for practical wastewater treatment.

Modulating the electron structure of Co-3d in Co3O4-x/WO2.72 for boosting peroxymonosulfate activation and degradation of sulfamerazine: Roles of high-valence W and rich oxygen vacancies

Sulfate radical (SO₄^•-)-based heterogonous advanced oxidation processes (AOPs) show promising potential to degrade emerging contaminants, however, regulating the electron structure of a catalyst to promote its catalytic activity is challenging. Herein, a hybrid that consists of Co₃O_4-x nanocrystals decorated on urchin-like WO_2.72 (Co₃O_4-x/WO_2.72) with high-valence W and rich oxygen vacancies (OVs) used to modulate the electronic structure of Co-3d was prepared. The Co₃O_4-x/WO_2.72 that developed exhibited high catalytic activity, activating peroxymonosulfate (PMS), and degrading sulfamerazine (SMR). With the use of Co₃O_4-x/WO_2.72, 100 % degradation of SMR was achieved within 2 min, at a pH of 7, with the reaction rate constant k₁ = 3.09 min^-1. Both characterizations and density functional theory (DFT) calculations confirmed the formation of OVs and the promotion of catalytic activity. The introduction of WO_2.72 greatly regulated the electronic structure of Co₃O_4-x. Specifically, the introduction of high-valence W enabled the Co-3d band centre to be closer to the Fermi level and enhanced electrons (e^-) transfer ability, while the introduction of OVs-Co in Co₃O_4-x promoted the activity of electrons in the Co-3d orbital and the subsequent catalytic reaction. The reactive oxygen species (ROS) were identified as •OH, SO₄^•-, and singlet oxygen (¹O₂) by quenching experiments and electron spin resonance (EPR) analysis. The DFT calculation using the Fukui index indicated the reactive sites in SMR were available for an electrophilic attack, and three degradation pathways were proposed.

Orientated construction of visible-light-assisted peroxymonosulfate activation system for antibiotic removal: Significant enhancing effect of Cl. JOURNAL OF HAZARDOUS MATERIALS 2023;445:130476. [PMID: 36455327 DOI: 10.1016/j.jhazmat.2022.130476]

Antibiotic contaminants can migrate over long distances in the water, thus possibly causing severe detriment to the environment and even potential harm to human health. Heterogeneous activation of peroxymonosulfate (PMS) assisted by visible light is an emerging and promising technology for the purification of such wastewater. This study designed an ultra-efficient and stable PMS activator (FeCN) to restore the typical antibiotic-polluted water under harsh conditions. About 90.94% of sulfamethoxazole (SMX) was degraded in 35 min in the constructed FeCN+PMS/vis system, and the reaction rate constant was nearly 50-fold higher than direct photocatalysis. Electron spin resonance, quenching experiments, LC/MS technique, eco-toxicity assessment, and density functional theory validated that the SMX removal was dominated by the attack of h⁺, ^•O₂^- and ¹O₂ on the active atoms of SMX molecules with high Fukui index, presenting as a simultaneous degradation and detoxification process. Such a visible-light-assisted PMS activation system also had good resistance to the environmental water bodies and a broad spectrum in the degradation of various pollutants. In particular, Cl^- (50 mM) could significantly accelerate the removal of SMX with a 32.6-fold increase in catalytic activity, and the mineralization efficiency could reach 56.6% under identical conditions. Moreover, this Cl^- containing system excluded the degradation products of disinfection by-products, and such a system was also versatile for different contaminants. This work demonstrates the feasibility of the FeCN+PMS/vis system for the remediation of antibiotic-contaminated wastewater in the presence and absence of Cl^-, and also highlights their great potential in WWTPs.

Non-radical degradation of organic pharmaceuticals by g-C3N4 under visible light irradiation: The overlooked role of excitonic energy transfer

In this work, an excitonic energy transfer (EET) based non-radical mechanism was proposed for the degradation of organic pharmaceuticals by graphitic carbon nitride (g-C₃N₄) under visible light irradiation. Using diclofenac (DCF) as a model molecule, the competition between single electron transfer (SET) and EET was studied through modulating the exciton binding energy of g-C₃N₄. The different mechanisms of SET and EET for DCF degradation were predicted by DFT calculation, and further confirmed by their different degradation pathways. When EET played an important role, the rationality of some very popular radical scavengers, such as p-BQ, TEMPOL and furfuryl alcohol must be reconsidered. In addition, humic acid (HA) had a distinct effect on EET and SET. Specifically, HA enhanced the EET process through photosensitization, but suppressed SET through radical quenching effect. The effect of HA on DCF degradation depended on the contribution ratio of SET and ET.

Rational design of cobalt sulfide anchored on nitrogen-doped carbon derived from cyanobacteria waste enables efficient activation of peroxymonosulfate for organic pollutants oxidation

With the increasing of eutrophication in water body, algae blooms have become one of the global environmental problems. The cyanobacteria waste has placed a severe burden on the environment and transforming cyanobacteria into functional materials may be a wise approach. Herein, cobaltous sulfide/nitrogen-doped biochar (N-BC/CoS_x) composite was synthesized by pyrolysis of cyanobacteria waste. The N-BC/CoS_x showed excellent performance in peroxymonosulfate (PMS) activation for enrofloxacin (ENR) degradation, which could remove more than 90% ENR within 60 min. The influencing factors of pH and catalyst dosage on ENR removal efficiency were studied. The N-BC/CoS_x showed good recyclability in the cycle runs. The radicals (O₂^•-, OH andSO₄^•-) and the non-radical species (charge transfer and ¹O₂) were generated in the ENR degradation. The cycle of Co(II)/Co(III) m ay contribute to the radical generation process. This work proved that metal sulfide modified cyanobacteria biochar has a specific application value in water pollution control and provides a new method for resource utilization of cyanobacteria.