Rapid quantitation of cyanide in whole blood by automated headspace gas chromatography

Simple and simultaneous quantification of cyanide, ethanol, and 1-propanol in blood by headspace GC–MS/NPD with Deans switch dual detector system

Cyanide is a powerful and rapidly acting poison. In Japan, cyanide poisoning is rare, and regular cyanide testing can be costly and time consuming. In contrast, alcohol analysis is routinely performed in most forensic laboratories. In this study, we attempted to develop a method for the simultaneous quantification of cyanide and alcohols in blood using headspace gas chromatography (HS-GC). As nitrogen-phosphorus detection (NPD) is more sensitive to hydrogen cyanide than mass spectrometry (MS), a Deans switch was used to switch the detectors during a single run. The separation provided by three analytical columns, PoraBOND Q, CP-Sil 5 CB, and HP-INNOWax, was investigated, and PoraBOND Q was selected. The use of HS-GC-MS/NPD with a Deans switch enabled the simple and simultaneous quantification of cyanide, ethanol, and 1-propanol. Eighteen other volatile compounds were detected in the SIM/scan mode of the MS.

A novel method for cyanide quantification in human whole blood using ion chromatography with amperometric detection and its application to cyanide intoxication cases

Cyanide is a highly toxic agent that has been frequently used for suicide in South Korea. It is also used in various industrial fields, such as metal plating, in which many accidental cyanide intoxications have occurred. To overcome the disadvantages of conventional cyanide analysis methods, a simple and fast method for the analysis of cyanide in whole blood using ion chromatography (IC) with amperometric detection was developed in this study. Whole blood samples were deproteinized, diluted, and analyzed using an IC-amperometric detection system. The limits of detection and quantitation were 0.1 and 0.2 mg/L, respectively. The method showed good linearity in the range of 0.2 to 50 mg/L with R²  > 0.99. The intra- and inter-assay precision and accuracy values were <10%. The established method was successfully applied to analyze whole blood samples from three cyanide intoxication cases.

Old Poison, New Problem: Cyanide Fatal Intoxications Associated with Internet Shopping

Widespread access to the Internet has an increasing influence on how suicides are committed. On websites such as eBay® or Amazon.com® highly toxic substances including cyanides are available for purchase. In the last 5 years, a few fatal intoxications associated with Internet shopping and buying "suicide kits" have been reported. Epidemiology of intoxications reported by American Association of Poison Control Centers between 2000-2018 shows that about 10% of all exposures to cyanide were related to suicide attempts and intentional ingestion of this substance. In order to determine the cyanide concentration in four fatal intoxication cases associated with Internet shopping, a headspace gas chromatography with dual column/dual flame ionization detector (HS-GC-FID/FID) method was validated and applied to casework. The method was linear in range, from 1 to 50 µg/mL, with a coefficient of determination of 0.999 (R2). The limit of quantification was 1.0 µg/mL; the detection limit was 0.5 µg/mL. Intra- and inter-day validation precision and accuracy did not exceed 10% and 15%, respectively. Recovery and matrix effect values ranged from 94.8- 103.8% and -5.2─3.8%, respectively. The cyanide concentrations were determined in biological fluids (blood, urine, bile, vitreous humor, gastric content) and postmortem tissue samples (spleen, kidney, liver, brain). The headspace gas chromatographic method, which is routinely used in clinical and forensic toxicology to quantify ethanol with its congeners (methanol, acetone, isopropanol, n-propanol and n-butanol), can be also applied to determine cyanide in intoxication cases. The global problem of a high number of suicides each year, requires increasing and more restrictive control of highly toxic substances available online as well as caution monitoring of human exposure to cyanide. This old and well known poison is being increasingly used nowadays for suicidal purposes, therefore determination of cyanide in biological samples is still important in terms of clinical and forensic toxicology.

Modified congener analysis: Quantification of cyanide in whole blood, other body fluids, and diverse beverages

The congener analysis is routinely used for the determination of volatile compounds in body fluids and beverages for forensic investigations. Although intoxications with cyanide via smoke inhalation or ingestion of cyanide salts are frequently encountered in forensic medicine, the inclusion of hydrogen cyanide in this analysis was never studied in detail. In this work, a very simple, fast, and sensitive quantification method with headspace gas chromatography and flame ionization detection for the analysis of cyanide in whole blood-was developed and validated. In contrast to the standard sample preparation of the congener analysis, an acidification step with tartaric acid was added. A limit of detection of 50 ng/ml, good linearity (coefficient of correlation > 0.9997), high accuracy (101.5%-106.4%), and precision (relative standard deviation 1.8%-3.7%) were achieved. Authentic blood samples of 10 forensic cases were investigated with the new method. Furthermore, the method was used for the quantification of cyanide in other body fluids (serum and urine) and diverse beverages. Interferences were investigated, and the addition of aldehydes produced a clear concentration-dependent decrease of the cyanide signal. Besides, the method offers an economical use of limited sample material by the simultaneous determination of cyanide, ethanol, and congener alcohols.

Solid phase microextraction techniques used for gas chromatography: a review

In the last decade, the development and adoption of greener and sustainable microextraction techniques have been proved to be an effective alternative to classical sample preparation procedures. In this review, 10 commercially available solid-phase microextraction systems are presented, with special attention to the appraisal of their analytical, bioanalytical, and environmental engineering. This review provides an overview of the challenges and achievements in the application of fully automated miniaturized sample preparation methods in analytical laboratories. Both theoretical and practical aspects of these environment-friendly preparation approaches are discussed. The application of chemometrics in method development is also discussed. We are convinced that green analytical chemistry will be really useful in the years ahead. The application of cheap, fast, automated, “clever”, and environmentally safe procedures to environmental, clinical, and food analysis will improve significantly the quality of the analytical data.

Assembling PVP-Au NPs as portable chip for sensitive detection of cyanide with surface-enhanced Raman spectroscopy

Cyanide (C≡N) can lead to blood, cardiovascular system, and nervous system disorders owing to the acute and chronic toxicity; thus, aiming at the group or individual poisoning incidents, it is necessary to develop the sensitive and credible method for rapid on-site detection of poisons cyanide. Surface-enhanced Raman spectroscopy (SERS) with the advantages of providing fingerprint information of target molecules and single-molecules sensitivity has been widely used in on-site analysis; however, the SERS measurements always suffer from the problem of the stability of substrates. Here, the polyvinylpyrrolidone (PVP)-stabilized Au NPs (PVP-Au NPs) have been assembled through the simple, convenient evaporation-induced strategy with the large-scale hotspots substrates. The presence of PVP can not only facilitate the assembly of Au NPs but also prevent the corrosion of CN^- towards the Au NPs with the formation of [Au (CN)₂]^-1, providing high stable and reproducible SERS signals. Moreover, the PVP-Au NPs have been assembled on the Si wafer to fabricate the portable SERS chip for rapid on-site detection of CN^- with an RSD of 5.8% and limitation of 100 ppb. Furthermore, by coupling a portable Raman spectrometer, the SERS spectra of CN^- spiked into different specimens to simulate the poison samples have been collected and analyzed on SERS chips with the recovery of 89-103% and RSD not higher than 11.3%. Consequently, the fabricated SERS chip with assembled PVP-Au NPs can provide sensitive and credible detection for CN^- in different specimens, and then would satisfy the rapid on-site evaluation of CN^- in poisoning incidents with the portable Raman spectrometer. Graphical Abstract.

Metabolism study for CUMYL-4CN-BINACA in human hepatocytes and authentic urine specimens: Free cyanide is formed during the main metabolic pathway

To further elucidate the metabolism of CUMYL-4CN-BINACA, a new synthetic cannabinoid with a cyano group, and to evaluate biomarkers, we incubated the substance in human hepatocytes and analysed 9 authentic urine specimens. We also quantified CUMYL-4CN-BINACA and cyanide in blood and provide comprehensive data on the 7 autopsy cases, 5 of them determined CUMYL-4CN-BINACA intoxications. For metabolite elucidation, CUMYL-4CN-BINACA was incubated with pooled human hepatocytes for up to 5 hours, urine samples were analysed with and without enzymatic hydrolysis. Data was acquired in data-dependent mode by ultra-high performance liquid chromatography-high resolution mass spectrometry (UHPLC-HRMS) with an Agilent 6550 QTOF. For quantitative analysis of CUMYL-4CN-BINACA, blood samples were precipitated and analysed by liquid chromatography-tandem mass spectrometry (LC-MS/MS). Cyanide was determined by gas chromatography-headspace-nitrogen phosphorus detection (GC-headspace-NPD). CUMYL-4CN-BINACA was metabolised via CYP450-mediated hydroxylation at 4-butyl position generating a cyanohydrin (M12), which releases free cyanide to form an aldehyde intermediate and eventually generates 4-hydroxybutyl CUMYL-BINACA (M11) and CUMYL-BINACA butanoic acid (M10). Other minor metabolites were produced by hydroxylation, dihydroxylation, N-dealkylation, and dihydrodiol formation; glucuronidation was observed. One urine sample showed high intensities of M10 and a wide variety of metabolites; the other samples contained fewer metabolites in low abundance and 1 sample showed no metabolites. CUMYL-4CN-BINACA blood concentrations ranged from 0.1 to 8.3 ng/g showing an overlap between fatal and non-fatal concentrations. One blood sample contained 0.36 μg/g cyanide. Release of free cyanide during metabolism is worrying as it might induce liver toxicity. As suggested earlier, CUMYL-BINACA butanoic acid is the most abundant biomarker in urine, but monitoring of additional metabolites or, even better, analysis for the parent in blood is recommended.

Current concepts in the pathophysiology and treatment of inhalation injury

The opinions or assertions contained herein are the private views of the author, and are not to be construed as official or as reflecting the official views of the Department of the Army or Department of Defense. Smoke inhalation injury occurs in about 10% of patients admitted to burn centres, and increases the mortality of burn patients by up to 20% over predictions based on age and burn size alone. The primary lesion in smoke inhalation injury is localized to the small airways, with alveolar injury and pulmonary oedema exercising a less prominent role during the initial phases. Injury incites a cascade of events that include ventilation-perfusion mismatch, secondary lung injury, systemic inflammation, impaired immune function, and pneumonia. The most important recent developments in the treatment of inhalation injury have included improved methods of pulmonary care targeted at the pathophysiology of the injury, such as high-frequency percussive ventilation and gentle mechanical ventilation.

Ultra-sensitive determination of cyanide in surface water by gas chromatography-tandem mass spectrometry after derivatization with 2-(dimethylamino)ethanethiol

A gas chromatography-tandem mass spectrometric (GC-MS/MS) method has been established for the determination of cyanide in surface water. This method is based on the derivatization of cyanide with 2-(dimethylamino)ethanethiol in surface water. The following optimum reaction conditions were established: reagent dosage, 0.7 g L(-1) of 2-(dimethylamino)ethanethiol; pH 6; reaction carried out for 20 min at 60°C. The organic derivative was extracted with 3 mL of ethyl acetate, and then measured by using GC-MS/MS. Under the established conditions, the detection and quantification limits were 0.02 μg L(-1) and 0.07 μg L(-1) in 10-mL of surface water, respectively. The calibration curve had a linear relationship relationship with y=0.7140x+0.1997 and r(2)=0.9963 (for a working range of 0.07-10 μg L(-1)) and the accuracy was in a range of 98-102%; the precision of the assay was less than 7% in surface water. The common ions Cl(-), F(-), Br(-), NO3(-), SO4(2-), PO4(3-), K(+), Na(+), NH4(+), Ca(2+), Mg(2+), Ba(2+), Mn(4+), Mn(2+), Fe(3+), Fe(2+) and sea water did not interfere in cyanide detection, even when present in 1000-fold excess over the species. Cyanide was detected in a concentration range of 0.07-0.11 μg L(-1) in 6 of 10 surface water samples.

LC-MS/MS analysis of 2-aminothiazoline-4-carboxylic acid as a forensic biomarker for cyanide poisoning

AIM

To demonstrate the potential of using 2-aminothiazoline-4-carboxylic acid (ATCA) as a novel biomarker/forensic biomarker for cyanide poisoning.

METHODS

A sensitive method was developed and employed for the identification and quantification of ATCA in biological samples, where the sample extraction and clean up were achieved by solid phase extraction (SPE). After optimization of SPE procedures, ATCA was analyzed by high performance liquid chromatography-tandem mass spectrometry. ATCA levels following the administration of different doses of potassium cyanide (KCN) to mice were measured and compared to endogenous ATCA levels in order to study the significance of using ATCA as a biomarker for cyanide poisoning.

RESULTS

A custom made analytical method was established for a new (mice) model when animals were exposed to increasing KCN doses. The application of this method provided important new information on ATCA as a potential cyanide biomarker. ATCA concentration in mice plasma samples were increased from 189 ± 28 ng/mL (n = 3) to 413 ± 66 ng/mL (n = 3) following a 10 mg/kg body weight dose of KCN introduced subcutaneously. The sensitivity of this analytical method proved to be a tool for measuring endogenous level of ATCA in mice organs as follows: 1.2 ± 0.1 μg/g for kidney samples, 1.6 ± 0.1 μg/g for brain samples, 1.8 ± 0.2 μg/g for lung samples, 2.9 ± 0.1 μg/g for heart samples, and 3.6 ± 0.9 μg/g for liver samples.

CONCLUSION

This finding suggests that ATCA has the potential to serve as a plasma biomarker / forensic biomarker for cyanide poisoning.

LC-MS/MS analysis of 2-aminothiazoline-4-carboxylic acid as a forensic biomarker for cyanide poisoning

AIM: To demonstrate the potential of using 2-aminothiazoline-4-carboxylic acid (ATCA) as a novel biomarker/forensic biomarker for cyanide poisoning.

METHODS: A sensitive method was developed and employed for the identification and quantification of ATCA in biological samples, where the sample extraction and clean up were achieved by solid phase extraction (SPE). After optimization of SPE procedures, ATCA was analyzed by high performance liquid chromatography-tandem mass spectrometry. ATCA levels following the administration of different doses of potassium cyanide (KCN) to mice were measured and compared to endogenous ATCA levels in order to study the significance of using ATCA as a biomarker for cyanide poisoning.

RESULTS: A custom made analytical method was established for a new (mice) model when animals were exposed to increasing KCN doses. The application of this method provided important new information on ATCA as a potential cyanide biomarker. ATCA concentration in mice plasma samples were increased from 189 ± 28 ng/mL (n = 3) to 413 ± 66 ng/mL (n = 3) following a 10 mg/kg body weight dose of KCN introduced subcutaneously. The sensitivity of this analytical method proved to be a tool for measuring endogenous level of ATCA in mice organs as follows: 1.2 ± 0.1 μg/g for kidney samples, 1.6 ± 0.1 μg/g for brain samples, 1.8 ± 0.2 μg/g for lung samples, 2.9 ± 0.1 μg/g for heart samples, and 3.6 ± 0.9 μg/g for liver samples.

CONCLUSION: This finding suggests that ATCA has the potential to serve as a plasma biomarker / forensic biomarker for cyanide poisoning.

Comparison of cyanide exposure markers in the biofluids of smokers and non-smokers

Cyanide is highly toxic and is present in many foods, combustion products (e.g. cigarette smoke), industrial processes, and has been used as a terrorist weapon. In this study, cyanide and its major metabolites, thiocyanate and 2-amino-2-thiazoline-4-carboxylic acid (ATCA), were analyzed from various human biofluids of smokers (low-level chronic cyanide exposure group) and non-smokers to gain insight into the relationship of these biomarkers to cyanide exposure. The concentrations of each biomarker tested were elevated for smokers in each biofluid. Significant differences (p < 0.05) were found for thiocyanate in plasma and urine, and ATCA showed significant differences in plasma and saliva. Additionally, biomarker concentration ratios, correlations between markers of cyanide exposure, and other statistical methods were performed to better understand the relationship between cyanide and its metabolites. Of the markers studied, the results indicate plasma ATCA, in particular, showed excellent promise as a biomarker for chronic low-level cyanide exposure.

Organ-distribution of the metabolite 2-aminothiazoline-4-carboxylic acid in a rat model following cyanide exposure

The reaction of cyanide (CN(-)) with cystine to produce 2-aminothiazoline-4-carboxylic acid (ATCA) is one of the independent detoxification pathways of cyanide in biological systems. In this report, in vivo production of ATCA and its distributions in plasma and organs were studied after a subcutaneous sublethal dose of 4 mg/kg body weight potassium cyanide (KCN) administration to rats. At this sublethal dose of KCN, ATCA concentration was not significantly increased in the plasma samples, however, it was found significantly increased in liver samples. These results suggested that ATCA might not be a good diagnostic biomarker in plasma for sublethal cyanide exposure; however, liver could serve as the right organ for the detection of ATCA in post-mortem examinations involving cyanide exposure in military, firefighting, industrial and forensic settings.

Unique cyanide adduct in human serum albumin: potential as a surrogate exposure marker

Cyanide (CN = HCN + CN(-)) is a renowned poison and neurotoxicant that is prevalent throughout the environment. Despite a plethora of studies conducted over the last half century, relatively little is known of its potential to cause adverse health outcomes at sublethal exposures. CN exposure is normally determined from blood, but because CN is rapidly metabolized and cleared from this compartment (t(1/2) < 1 h), it is common for several half-lives to have passed before blood samples are drawn for analysis. This variable, coupled with a very narrow toxic index and metabolic diversity within the human population, has rendered accurate assessment of CN exposure, and consequently any predictions of possible adverse health outcomes, highly problematic. Prior studies by us showed the potential of Cys-SCN adducts within human serum albumin (HSA) to act as retrospective surrogates of CN exposure. Here, we report the discovery of a stable, SCN adduct at Cys(567) formed by the reaction of CN with the C-terminal Cys(558)Cys(567) disulfide bond of HSA. Treatment of HSA purified from human serum with base in guanidine hydrochloride releases a readily detectable, uniquely modified, C-terminal-19-mer peptide from Cys(567)-SCN moieties in all the samples examined thus far. Inclusion of a HSA-Cys(567)-S(13)C(15)N labeled internal standard permits quantitation of the Cys(567)-SCN adduct by LC-MS/MS in selective reaction monitoring (SRM) of the surrogate peptide with high sensitivity and good precision. Reaction of CN in vitro with the Cys(558)Cys(567) disulfide bond in HSA is specific, rapid, and concentration dependent within a putative, physiologically relevant range. Data from various human sera demonstrate the potential usefulness of this adduct as a biomarker of CN exposure.

New facile method to measure cyanide in blood

Cyanide, a well-known toxic substance that could be used as a weapon of mass destruction, is likely responsible for a substantial percentage of smoke inhalation deaths. The vitamin B(12) precursor cobinamide binds cyanide with high affinity, changing color and, correspondingly, its spectrophotometric spectrum in the ultraviolet/visible light range. Based on these spectral changes, we developed a new facile method to measure cyanide in blood using cobinamide. The limit of detection was 0.25 nmol, while the limit of quantitation was approximately 0.5 nmol. The method was reliable, requires minimal equipment, and correlated well with a previously established method. Moreover, we adapted it for rapid qualitative assessment of cyanide concentration, which could be used in the field to identify cyanide-poisoned subjects for immediate treatment.

Determination of cyanide in blood by isotope-dilution gas chromatography-mass spectrometry

BACKGROUND

Cyanide (CN) is a lethal toxin. Quantification in blood is necessary to indicate exposure from many sources, including food, combustion byproducts, and terrorist activity. We describe an automated procedure based on isotope-dilution gas chromatography-mass spectrometry (ID GC/MS) for the accurate and rapid determination of CN in whole blood.

METHODS

A known amount of isotopically labeled potassium cyanide (K13C15N) was added to 0.5 g of whole blood in a headspace vial. Hydrogen cyanide was generated through the addition of phosphoric acid, and after a 5-min incubation, 0.5 mL of the headspace was injected into the GC/MS at an oven temperature of -15 degrees C. The peak areas from the sample, 1H12C14N+, at m/z 27, and the internal standard, 1H13C15N+, at m/z 29, were measured, and the CN concentration was quantified by ID. The analysis time was 15 min for a single injection.

RESULTS

We demonstrated method accuracy by measuring the CN content of unfrozen whole blood samples fortified with a known amount of CN. Intermediate precision was demonstrated by periodic analyses over a 14-month span. Relative expanded uncertainties based on a 95% level of confidence with a coverage factor of 2 at CN concentrations of 0.06, 0.6, and 1.5 microg/g were 8.3%, 5.4%, and 5.3%, respectively. The mean deviation from the known value for all concentrations was <4%.

CONCLUSION

The automated ID GC/MS method can accurately and rapidly quantify nanogram per gram to microgram per gram concentrations of CN in blood.

An improved method for cyanide determination in blood using solid-phase microextraction and gas chromatography/mass spectrometry

A new method is described for the qualitative and quantitative analysis of cyanide, a very short-acting and powerful toxic agent, in human whole blood. It involves the conversion of cyanide into hydrogen cyanide and its subsequent headspace solid-phase microextraction (HS-SPME) and detection by gas chromatography/mass spectrometry (GC/MS) in selected ion monitoring (SIM) mode. Optimizing the conditions for the GC/MS (type of column, injection conditions, temperature program) and SPME (choice of SPME fiber, effect of salts, adsorption and desorption times, adsorption temperature) led to the choice of a 75-microm carboxen/polydimethylsiloxane SPME fiber, with D3-acetonitrile as internal standard, and a capillary GC column with a polar stationary phase. Method validation was carried out in terms of linearity, precision and accuracy in both aqueous solutions and blood. The limit of detection (LOD) and limit of quantitation (LOQ) were determined only in aqueous solutions. The assay is linear over three orders of magnitude (water 0.01-10, blood 0.05-10 microg/mL); and the LOD and LOQ in water were 0.006 and 0.01 microg/mL, respectively. Good intra- and inter-assay precision was obtained, always <8%. The method is simple, fast and sensitive enough for the rapid diagnosis of cyanide intoxication in clinical and forensic toxicology.

Determination of HCN sampled from gasification product gases by headspace gas chromatography with atomic emission detector

Nitrogen-containing fuels produce hydrogen cyanide when the fuel is gasified. The gas is poisonous and produces nitrogen oxides when it is burned. HCN is usually sampled into alkaline solutions and analysed using an ion selective electrode. The method is tedious and the electrode response is temperature-dependent. Samples are not stable and must be analysed immediately, and they contain ions which are poisonous to the electrode. Therefore a new gas chromatographic method was developed. In this new method HCN is released from the alkaline solutions with sulphuric acid in a headspace sampler and analysed by a gas chromatograph connected to an atomic emission detector. Measurements on carbon emission line 193.1 nm gave the limit of detection 0.05 mg CN-/l in the solution. The calibration curve was linear to 1000 mg CN-/l and the correlation was 0.997. The relative standard deviation of the calibration was 1.7% at the concentration of 5 mg CN-/l and 1.0% at 25 mg CN-/l. The developed headspace method allows automated analysis and it needs less sample preparations than the ion selective electrode method. This paper also reports the effect of sample preparation and storage time on the stability of the samples.

Carbon Monoxide and Cyanide Poisoning in Fire Related Deaths in Victoria, Australia

OBJECTIVE

This study was undertaken to examine the association of hydrogen cyanide and carboxyhaemoglobin in victims of fire related deaths in Australia. The secondary aim was to document demographic data about Australian fire related deaths.

METHODS

An observational retrospective study was undertaken of autopsy reports from the Victorian Institute of Forensic Medicine. Reports of fire related deaths were electronically searched using the terms burns, "smoke" or "fire" as a cause of death in the calender years 1992 to 1998. Data on the circumstances of the fire and results of toxicological screening were obtained on 178 persons. Additional whole blood cyanide levels were determined if blood samples were available in storage. Demographics of the victims were analysed, as well as the relationship between carboxyhaemoglobin and whole blood cyanide levels.

RESULTS

Most (82%) of the victims died at the scene, whilst 32 victims died after a period of hospitalisation (hours to weeks). Suicide as a result of self-immolation was the reported cause of death in 32 cases. Most of the fires were in houses (114) and cars (29). The blood ethanol level was zero in 112 cases; the remaining cases (53) had a mean level of 0.17%. Other central nervous system (CNS) depressants were recorded in 49 of the 134 cases that received a complete toxicological screen. Carboxyhaemoglobin levels were measured in only 154 of 178 cases. The carboxyhaemoglobin level was zero in 43 cases. The remaining cases (111) had a mean level of 40%; with 44 cases having a level greater than 50%, a level considered to be potentially lethal. Whole blood hydrogen cyanide levels were measured in only 138 of 178 cases. The hydrogen cyanide level was zero in 52 cases. The remaining cases (86) had a mean level of 1.65 mg/L; with 11 cases having a level greater than 3.0 mg/L (potentially fatal). Blood ethanol levels were significantly correlated with both carboxyhaemoglobin (R = 0.22, P < 0.01) and cyanide (R = 0.36, P < 0.001). In addition, a significant correlation (r = 0.34) between carboxyhaemoglobin and hydrogen cyanide levels was noted.

CONCLUSIONS

This study showed a correlation between elevated blood ethanol and whole blood cyanide levels (r = 0.36, p < 0.001) and between elevated carboxyhaemoglobin and hydrogen cyanide levels (r = 0.34). Although the mean cyanide level was 1.3 mg/L (above the level some consider potentially toxic) in those cases with a carboxyhaemoglobin level of greater than 10%, there is insufficient data to permit recommendations for clinical care. Further studies are required on those victims that reach hospital alive.

Methods for assaying cyanide in bacterial culture supernatant

AIMS

To find an easy, rapid and direct method for the quantitation of cyanide in a moderate number of bacterial culture supernatants.

METHODS AND RESULTS

Culture supernatant from stationary phase cultures of Pseudomonas aeruginosa, grown in LB media, were analysed for cyanide content using the Merckoquant and Spectroquant cyanide detection kits as well as a cyanide ion-selective electrode (ISE) and a cyanide micro-ISE. The Merckoquant kit, designed for detection of low quantities of cyanide in water systems, proved not to be sufficiently reliable, providing poor comparison with previous assessments of cyanide levels in Ps. aeruginosa. The Spectroquant kit, and the two ISEs all provided very similar results, in agreement with previous data; however, it was the ISEs that fulfilled all the criteria for a rapid, direct test in a moderate number of samples.

CONCLUSIONS

Cyanide ISEs can be used for easy assessment of the cyanide quantity in cultures grown in LB medium.

SIGNIFICANCE AND IMPACT OF THE STUDY

The use of a cyanide ISE allows for an easy, direct and reproducible method for assaying cyanide in bacterial culture supernatant, which is of significant advantage over the currently accepted methods. This is especially important in an era of high-output genomic studies for assessing the phenotypic significance of data relating to the cyanide synthetic genes.

Derivatisation reactions in the chromatographic analysis of chemical warfare agents and their degradation products

The analysis of chemical warfare agents and their degradation products is an important component of verification of compliance with the Chemical Weapons Convention. Gas and liquid chromatography, particularly combined with mass spectrometry, are the major techniques used to detect and identify chemicals of concern to the Convention. The more polar analytes, and some of the more reactive or highly volatile agents, are usually derivatised to facilitate chromatography, and to impart properties beneficial for detection. This review focuses on derivatisation reactions used in the chromatographic analysis of chemical warfare agents, their degradation products and metabolites.