Salinity Gradients for Sustainable Energy: Primer, Progress, and Prospects

Software-Defined Optical Coherence Measurement of Seawater Refractive Index Variations

The seawater refractive index is an important parameter in marine environments, with its variations depending on the specific environmental conditions. During practical applications, modulation parameters such as the sampling rate, bandwidth, and filters directly affect the signal-to-noise ratio (SNR) and need to be adjusted in real-time according to the characteristics of the target signal. Low-cost software-defined radio (SDR) offers significant advantages in this regard. This paper proposes an optical coherence measurement method for seawater refractive index changes based on orthogonal demodulation using SDR along with simulation calculations, and the results demonstrate that the resolution of the refractive index change rate is 3.165×10-9 RIU/s, corresponding to a refractive index change resolution of 10-10 RIU (frequency range 1 Hz-100 Hz, measurement range 0.1 m). By adopting SDR as the implementation platform for the demodulation algorithm and using a radio-frequency source to simulate interference signals for demodulating the refractive index variation, the results show that the relative error of the SDR demodulation results is below 0.3%. Additionally, this study developed a software-defined optical coherence measurement system for the seawater refractive index and measured the refractive index changes in deionized water during heating. The experimental results showed that the root mean square error (RMSE) of the refractive index changes obtained through SDR demodulation was 5.68×10-6 RIU. This research provides a novel demodulation method for high-precision measurements of seawater refractive index changes under different marine environments.

Light-enhanced ion transport and fouling resistance properties of metal/semiconductor heterojunction nanochannel membranes for osmotic energy recovery in real-world conditions

Osmotic energy, abundant in seawater and high-salinity industrial wastewater, is a highly promising renewable "blue energy". However, practical osmotic energy recovery has been hindered by challenges such as membrane fouling caused by complex aqueous environment. In this study, we developed light-activated heterogeneous nanochannel membranes by continuous stacking two-dimensional semiconducting and metal-like nanosheets, significantly enhancing both ion transport efficiency and stability in complex, real-world aqueous environments. By leveraging light to create temperature gradients and built-in electric fields, solar energy was efficiently converted into a powerful driving force, markedly boosting ion transport efficiency. More importantly, the membrane continuously generated free radicals via photoexcitation and storage, effectively mitigating membrane fouling-even in low-light and nighttime conditions. As a result, while power density initially decreased by maximum of 87 % within 12 h due to organic contamination, it not only recovered to its original level under light exposure but also achieved a twofold increase, demonstrating robust energy recovery performance. Over 60 days of testing in Bohai Sea water, coal chemical wastewater from Shaanxi, and Da Qaidam Salt Lake brine, the system maintained stable power densities of up to 5.43 W/m2 with a membrane area of 0.2 mm2. This work marks a significant leap from the conceptual stage to the practical application of osmotic energy recovery, offering valuable insights into its scalability and real-world potential.

Blue Energy Extraction Performance by Polyelectrolyte-Coated Porous Electrodes: Effects of Opposing Polyelectrolyte Interaction in Micropores

In the capacitive mixing technique, the electrode used to extract blue energy is typically composed of a carbon-based porous electrode material. Polyelectrolyte (PE) surface coating on porous electrodes serves as an intermediate soft layer, which can significantly enhance the energy extraction performance (EEP). Herein, the blue energy extraction performance by using PE-coated electrodes is studied by a statistical thermodynamic theory, with the exploration of the interplay effects between opposing polyelectrolyte interactions and pore size. Because of the interaction between opposing PE coatings, the response of electrostatic properties in the pore to surface potential variations is enhanced during charging/discharging processes, leading to a better EEP. Both the surface charge accumulation and surface potential rise in the charging process can be raised as the results of PE coating. For the cases studied, the extraction efficiency can be promoted up to 45% compared with the cases of bare electrodes. For narrow pores, the PE promotion effects are suppressed by strong pore confinement. The optimal PE coating condition is determined by the competitive results between pore size (H) and polyelectrolyte chain length (N), with that Ĥ ≡ H/(2Nσ) being mostly in [0.1, 0.5], where σ is the PE segment diameter.

Designing and Optimizing Electrode Materials for Energy Harvesting in CAPMIX Cells

The growing demand for clean, decentralized energy has increased interest in blue energy, which generates power from water with different salt concentrations. Despite its potential as a renewable, low-cost energy source, optimizing electrode materials remains a challenge. This work presents a nanomaterial developed via microwave-assisted sol-gel methodology for blue energy applications, where ion diffusion and charge storage are critical. AX-7 carbon, designed for this study, features wide pores, enhancing ion diffusion. Compared to commercial NORIT carbon, AX-7 has a higher mesopore volume and external surface area, improving its overall performance. The synthesis process has been optimized and scaled up for evaluation in CAPMIX electrochemical cell stacks. Moreover, the lower series resistance (Rs) significantly boosts energy recovery, with AX-7 demonstrating superior performance. This advantage is especially evident during fresh-water cycles, where this material achieves significantly lower Rs compared to the commercial one.

Turing-type nanochannel membranes with extrinsic ion transport pathways for high-efficiency osmotic energy harvesting

Two-dimensional (2D) nanofluidic channels with confined transport pathways and abundant surface functional groups have been extensively investigated to achieve osmotic energy harvesting. However, solely relying on intrinsic interlayer channels results in insufficient permeability, thereby limiting the output power densities, which poses a significant challenge to the widespread application of these materials. Herein, we present a nanoconfined sacrificial template (NST) strategy to create a crafted channel structure, termed as Turing-type nanochannels, within the membrane. Extrinsic interlaced channels are formed between the lamellae using copper hydroxide nanowires as sacrificial templates. These Turing-type nanochannels significantly increase transport pathways and functional areas, resulting in a 23% enhancement in ionic current while maintaining a cation selectivity of 0.91. The output power density of the Turing-type nanochannel membrane increases from 3.9 to 5.9 W m-2 and remains stable for at least 120 hours. This membrane exhibits enhanced applicability in real saltwater environments across China, achieving output power densities of 7.7 W m-2 in natural seawater and 9.8 W m-2 in salt-lake brine. This work demonstrates the promising potential of the Turing-channel design for nanoconfined ionic transport in the energy conversion field.

Regulating V2O5 Layer Spacing by a Polyaniline Molecule Chain to Improve Electrochemical Performance in Salinity Gradient Energy Conversion

Salinity gradient energy is a chemical potential energy between two solutions with different ionic concentrations, which is also an ocean energy at the junction of rivers and seas. In our original work, the device "activated carbon//(0.083 M Na2SO4, 0.5 M Na2SO4)//vanadium pentoxide" for the conversion of salinity gradient energy was designed, and the conversion value of 6.29 J g-1 was obtained. However, the low specific surface area of the original V2O5 inevitably resulted in limited active sites and slow ionic transport rates, and the inherent lower conductivity and narrower layer spacing of the original V2O5 also resulted in poor electrode kinetic performance and cycle stability, hindering its practical application. To solve the above problems, the present work provides a strategy of using polyaniline (PANI) molecule chain intercalation to regulate the layer spacing of the original V2O5, and through the expansion and traction of the layer spacing, the composite PANI/V2O5 (PVO) with high specific surface area is prepared and used as an anode material for electrochemical conversion of salinity gradient energy application. The significantly increased layer spacing of the crystal plane (001) corresponding to the original V2O5 was confirmed with the PANI by the hydrogen bonding and the van der Waals force. The high specific surface area of the composite provides more electrochemical active sites to realize a fast Na+ migration rate and high specific capacitance. Meanwhile, the inserted PANI molecule chain, which acts not only as a pillar enlarging the Na+ diffusion channel but also as an anchor locking the gap between V2O5 bilayers, improves the structural stability of the V2O5 electrode during the electrochemical conversion process. The proposed insertion strategy for the conductive polymer PANI has created a new way to improve the cycle stability performance of the salinity gradient energy conversion device.

Multi-Interface Engineering of MXenes for Self-Powered Wearable Devices

Self-powered wearable devices with integrated energy supply module and sensitive sensors have significantly blossomed for continuous monitoring of human activity and the surrounding environment in healthcare sectors. The emerging of MXene-based materials has brought research upsurge in the fields of energy and electronics, owing to their excellent electrochemical performance, large surface area, superior mechanical performance, and tunable interfacial properties, where their performance can be further boosted via multi-interface engineering. Herein, a comprehensive review of recent progress in MXenes for self-powered wearable devices is discussed from the aspects of multi-interface engineering. The fundamental properties of MXenes including electronic, mechanical, optical, and thermal characteristics are discussed in detail. Different from previous review works on MXenes, multi-interface engineering of MXenes from termination regulation to surface modification and their impact on the performance of materials and energy storage/conversion devices are summarized. Based on the interfacial manipulation strategies, potential applications of MXene-based self-powered wearable devices are outlined. Finally, proposals and perspectives are provided on the current challenges and future directions in MXene-based self-powered wearable devices.

Nanoarchitectonics in Advanced Membranes for Enhanced Osmotic Energy Harvesting

Osmotic energy, often referred to as "blue energy", is the energy generated from the mixing of solutions with different salt concentrations, offering a vast, renewable, and environmentally friendly energy resource. The efficacy of osmotic power production considerably relies on the performance of the transmembrane process, which depends on ionic conductivity and the capability to differentiate between positive and negative ions. Recent advancements have led to the development of membrane materials featuring precisely tailored ion transport nanochannels, enabling high-efficiency osmotic energy harvesting. In this review, ion diffusion in confined nanochannels and the rational design and optimization of membrane architecture are explored. Furthermore, structural optimization of the membrane to mitigate transport resistance and the concentration polarization effect for enhancing osmotic energy harvesting is highlighted. Finally, an outlook on the challenges that lie ahead is provided, and the potential applications of osmotic energy conversion are outlined. This review offers a comprehensive viewpoint on the evolving prospects of osmotic energy conversion.

Mitigating the influence of multivalent ions on power density performance in a single-membrane capacitive reverse electrodialysis cell

In recent years, the energy generated by the salinity gradient has become a subject of growing interest as a source of renewable energy. One of the most widely used processes is reverse electrodialysis (RED), based on the use of ion exchange membranes and Faradaic electrodes. However, the use of real salt solutions containing mixtures of divalent and monovalent ions in the RED process results in a significant loss of recovered power, compared with salt solutions containing only monovalent ions. From an original point of view, in this work we study and explain the influence of divalent ions and complex solutions in reverse electrodialysis devices equipped with capacitive electrodes with a single membrane (CREDSM). We show that CREDSM mitigates the impact of divalent ions. From a quantitative point of view, the power recovered in a Faradaic cell drops by more than 75 % when the solutions contain 50 % molar fraction of divalent ions and by 33 % when the solutions contain 10 % molar fraction of divalent ions. For similar low-cost membranes with fairly low selectivity, recovered power drops by only 34 % when solutions contain 60 % moles of divalent ions in CREDSM. We show that only the membrane potential, which makes up half of the cell's open circuit potential, is affected. The potential of capacitive electrodes which counts for half of the potential cell does not decrease in the presence of divalents. For the same membrane under the same conditions, we estimate a loss of 62 % in a RED device Furthermore, the membrane is not poisoned by divalent ions because we periodically change the electrical current direction, by means of switching the feed waters. CREDSM devices do not show any variation in membrane resistance or membrane selectivity. The techno-economic analysis suggests further valorization of salinity gradients in industrial operations.

Harnessing Solar-Salinity Synergy with Porphyrin-Based Ionic Covalent-Organic-Framework Membranes for Enhanced Ionic Power Generation

Nature seamlessly integrates multiple functions for energy conversion, utilizing solar energy and salinity gradients as the primary drivers for ionic power generation. The creation of artificial membranes capable of finely controlling ion diffusion within nanoscale channels, driven by diverse forces, remains a challenging endeavor. In this study, we present an innovative approach: an ionic covalent-organic framework (COF) membrane constructed using chromophoric porphyrin units. The incorporation of ionic groups within these nanoconfined channels imparts the membrane with exceptional charge screening capabilities. Moreover, the membrane exhibits photoelectric responsivity, enhancing the ion conductivity upon exposure to light. As a result, this leads to a substantial increase in the output power density. In practical terms, when subjected to a salinity gradient of 0.5/0.01 M NaCl and exposed to light, the device achieved an outstanding peak power density of 18.0 ± 0.9 W m-2, surpassing the commercial benchmark by 3.6-fold. This innovative membrane design not only represents a significant leap forward in materials science but also opens promising avenues for advancing sustainable energy technologies.

Unleashing the Power of Osmotic Energy: Metal Hydroxide-Organic Framework Membranes for Efficient Conversion

Osmotic energy, as a renewable clean energy with huge energy density and stable yield, has received widespread attention over the past decades. Reverse electrodialysis (RED) based on ion-exchange membranes is an important method of obtaining osmotic energy from salinity gradients. The preparation of ion-exchange membranes with both high ion selectivity and ion permeability is in constant exploration. In this work, metal hydroxide-organic framework (MHOF) membranes are successfully prepared onto porous anodic aluminum oxide (AAO) membranes by a facile hydrothermal method to form Ni2(OH)2@AAO composite membranes, used for osmotic energy conversion. The surface is negatively charged with cation selectivity, and the asymmetric structure and extreme hydrophilicity enhance the ionic flux for effective capture of osmotic energy. The maximum output power density of 5.65 W m-2 at a 50-fold KCl concentration gradient is achieved, which exceeds the commercial benchmark of 5 W m-2. Meanwhile, the composite membrane can also show good performance in different electrolyte solutions and acid-base environments. This work provides a new avenue for the construction and application of MHOF membranes in efficient osmotic energy conversion.

Advances in Two-Dimensional Ion-Selective Membranes: Bridging Nanoscale Insights to Industrial-Scale Salinity Gradient Energy Harvesting

Salinity gradient energy, often referred to as the Gibbs free energy difference between saltwater and freshwater, is recognized as "blue energy" due to its inherent cleanliness, renewability, and continuous availability. Reverse electrodialysis (RED), relying on ion-selective membranes, stands as one of the most prevalent and promising methods for harnessing salinity gradient energy to generate electricity. Nevertheless, conventional RED membranes face challenges such as insufficient ion selectivity and transport rates and the difficulty of achieving the minimum commercial energy density threshold of 5 W/m2. In contrast, two-dimensional nanostructured materials, featuring nanoscale channels and abundant functional groups, offer a breakthrough by facilitating rapid ion transport and heightened selectivity. This comprehensive review delves into the mechanisms of osmotic power generation within a single nanopore and nanochannel, exploring optimal nanopore dimensions and nanochannel lengths. We subsequently examine the current landscape of power generation using two-dimensional nanostructured materials in laboratory-scale settings across various test areas. Furthermore, we address the notable decline in power density observed as test areas expand and propose essential criteria for the industrialization of two-dimensional ion-selective membranes. The review concludes with a forward-looking perspective, outlining future research directions, including scalable membrane fabrication, enhanced environmental adaptability, and integration into multiple industries. This review aims to bridge the gap between previous laboratory-scale investigations of two-dimensional ion-selective membranes in salinity gradient energy conversion and their potential large-scale industrial applications.

Highly Efficient Conversion of Salinity Difference to Electricity in Nanofluidic Channels Boosted by Variable Thickness Polyelectrolyte Coating

The inherent limits of the current produced by imposing salinity gradients along a nanofluidic channel having "hard" boundary walls heavily constrain the resulting energy harvesting efficacy, acting as major hindrances against the practicability of harnessing high power density from the mixing of water having different salinities. In this work, the infusion of variable-thickness polyelectrolyte layer of a conical shape is projected to augment salinity gradient power generation in nanochannels. Such a progressive thickening of a charged interfacial layer on account of axially declining ion concentration facilitates the shedding of enhanced numbers of mobile ions, bearing a net charge of equal and opposite to the surface-bound ions, into the mainstream current flow. We show that the proposed design can convert energy at a higher efficiency as compared to both solid-state and available polyelectrolyte layer (PEL)-covered nanochannels. The same is true for the maximum power density at moderate and high concentration ratios including natural salt gradient conditions for which more than 50% increase is achievable. The maximum values achieved for efficiency and power density read 50.3% and 6.6 kW/m2, respectively. Our results provide fundamental insights on strategizing variable-thickness polyelectrolyte layer grafting on the nanochannel interfaces, toward realizing high-performance osmotic power generators by altering the local ionic clouds alongside the grafted layers and enhancing the ionic mobility by inducing a driving potential gradient concomitantly. These findings open up a new strategy of efficient conversion of the power of the salinity difference of seawater and river water into electricity in a nanofluidic framework, surpassing the previously established limits of blue energy harvesting technologies.

Anti-Entropy Aggregation of Minority Groups in Polymers: Design and Applications

Minority groups are non-repeating units with very low content that inevitably exist in polymers. Typically, these minority groups are easily surrounded by the majority of repeating units and randomly dispersed, maximizing the entropy of minority groups. In the concept, anti-entropy aggregation (AEA) of minority groups is described, and different pathways are outlined. They are polymer crystallization-driven AEA, supramolecular interaction-induced AEA, phase separation-confined AEA, and hierarchical interactions-driven AEA. Typical applications of AEA materials are also presented, including fluorescence probes, self-healing materials, ion transporting regulation, and osmotic energy conversion. The concept of AEA is expected to inspire the fabrication of novel functional systems.

Boosting Salinity Energy Extraction Efficiency in Capacitive Mixing by Polyelectrolyte Surface Coating

The extraction of salinity gradient energy in the capacitive mixing (CapMix) technique can be enhanced by using polyelectrolyte-coated electrodes. The micromechanism of polyelectrolyte (PE) coating enhancing the salinity energy extraction is studied by using a statistical thermodynamic theory. When PE takes same charge sign as the coated electrodes, the extraction efficiency can be boosted owing to the enhanced response of electrical double layer (EDL) to external cell voltage (V0). For the optimal case studied, the extraction efficiency was boosted from 0.25 to 1.25% by PE coatings. Owing to counterion adsorption and the enhanced response of EDL, the extraction energy density presented a local maximum at V0 = 0, which is higher than another local maximum value when V0 ≠ 0. This provides important guidance on the two approaches of CapMix in terms of capacitive Donnan potential (CDP, V0 = 0) and capacitive double-layer expansion (CDLE, V0 ≠ 0). Under the effects of PE coating, the extraction efficiency by CDLE can be improved to about 11% by CDP for the optimal studied case. The synergistic effect of grafting conditions can significantly elevate the energy density and extraction efficiency of the CDP process.

Internal Electric Field Facilitates Facet-Dependent Photocatalytic Cl- Utilization on BiOCl in High-Salinity Wastewater for Ammonium Removal

High Cl- concentration in saline wastewater (e.g., landfill leachate) limits wastewater purification. Catalytic Cl- conversion into reactive chlorine species (RCS) arises as a sustainable strategy, making the salinity profitable for efficient wastewater treatment. Herein, aiming to reveal the structure-property relationship in Cl- utilization, bismuth oxychloride (BiOCl) photocatalysts with coexposed {001} and {110} facets are synthesized. With an increasing {001} ratio, the RCS production efficiency increases from 75.64 to 96.89 μg L-1 min-1. Mechanism investigation demonstrates the fast release of lattice Cl- as an RCS and the compensation of ambient Cl-. Correlation analysis between the internal electric field (IEF, parallel to [001]) and normalized efficiency on {110} (kRCS/S{110}, perpendicular to [001]) displays a coefficient of 0.86, validating that the promoted carrier dynamics eventually affects Cl- conversion on the open layered structure. The BiOCl photocatalyst is well behaved in ammonium (NH4+-N) degradation ranging from 20 to 800 mg N L-1 with different chlorinity (3-12 g L-1 NaCl). The sustainable Cl- conversion into RCS also realizes 85.4% of NH4+-N removal in the treatment of realistic landfill leachate (662 mg of N L-1 NH4+-N). The structure-property relationship provides insights into the design of efficient catalysts for environment remediation using ambient Cl-.

Review of the marine energy environment-a combination of traditional, bibliometric and PESTEL analysis

Marine renewable energy is regarded as a nascent renewable energy resource that is less utilized due to a number of challenges in the sector. This paper focused on using both traditional and bibliometric analysis approaches to review the marine energy industry. It also assessed the various opportunities and challenges in the sector beyond technological challenges using PESTEL analysis. The results from the study identified the availability of renewable energy targets, international and national greenhouse gas (GHG) emissions reduction targets, job creation, skill transfer from offshore industries, renewable support, and low GHG emissions as the major opportunities for the sector. The challenges in the sector include the lack of commonality in device designs, high initial capital costs, lack of appropriate legal and regulatory frameworks, lack of funding, fragmentations in regulatory institutions, bad macro-economic indicators in some countries, environmental challenges, the survivability of the various technologies in the harsh oceanic environment, and strong competition from other renewable energy sources. The outcome of the bibliometric analysis spanning from 2013 to 2023 shows that tidal power is the focus of research in the field, and most studies are either focused on ways to improve its efficiency in terms of technology or on the identification of resource potentials for the siting of the various marine renewable power systems. Recommendations such as strong cooperation between the government and private sector, increased public education, collaboration with existing players in the marine sector, and increased research and development, among others, were proposed for the development of the sector.

Charge-Gradient Sulfonated Poly(ether ether ketone) Membrane with Enhanced Ion Selectivity for Osmotic Energy Conversion

Engineered asymmetric heterogeneous ion-selective membranes have become a focal point for their improved efficiency in harnessing osmotic energy from ionic solutions with varying salinity. However, achieving both energy conversion efficiency and excellent chemical stability necessitates effectively mitigating the formation of detrimental interface cracks between two different layers. We develop a charge-gradient sulfonated poly(ether ether ketone) (SPEEK) membrane (CG-SPEEK) on a large-scale using a straightforward coating method. As an osmotic energy generator, CG-SPEEK membrane achieves an impressive output power density of 9.2 W m-2 and exhibits ultrahigh cation selectivity (0.99), with an energy conversion efficiency of 48% at a 50-fold NaCl concentration gradient. The results highlight the ion diode effects of CG-SPEEK, driven by a charge density gradient that accelerates cation transport while suppressing ion concentration polarization. Density functional theory simulations provide further insights, revealing that the energy barrier for Na+ ion transport through CG-SPEEK membrane is lower than that through a homogeneous SPEEK membrane. This work not only enhances our understanding of ion transport dynamics but also establishes the CG-SPEEK membrane as a promising candidate for efficient osmotic energy conversion applications.

Construction of metal-organic framework/cellulose nanofibers-based hybrid membranes and their ion transport property for efficient osmotic energy conversion

The development of advanced nanofluidic membranes with better ion selectivity, efficient energy conversion and high output power density remains challenging. Herein, we prepared nanofluidic hybrid membranes based on TEMPO oxidized cellulose nanofibers (T-CNF) and manganese-based metal organic framework (MOF) using a simple in situ synthesis method. Incorporated T-CNF endows the MOF/T-CNF hybrid membrane with a high cation selectivity up to 0.93. Nanoporous MOF in three-dimensional interconnected nanochannels provides massive ion transport pathways. High transmembrane ion flux and low ion permeation energy barrier are correlated with a superior energy conversion efficiency (36 %) in MOF/T-CNF hybrid membrane. When operating under 50-fold salinity gradient by mixing simulated seawater and river water, the MOF/T-CNF hybrid membrane achieves a maximum power density value of 1.87 W m-2. About 5-fold increase in output power density was achieved compared to pure T-CNF membrane. The integration of natural nanofibers with high charge density and nanoporous MOF materials is demonstrated an effective and novel strategy for the enhancement of output power density of nanofluidic membranes, showing the great potential of MOF/T-CNF hybrid membranes as efficient nanofluidic osmotic energy generators.

Unlocking energy potential: Decarbonizing water reclamation plants with salinity gradient energy recovery

Climate change, together with the ecological droughts suffered by a large part of the European Union's territory, calls for joint environmental solutions. In this regard, water reclamation is a promising way to alleviate the pressure on existing water resources. However, reuse strategies are penalized by the extra energy consumed in urban wastewater treatment plants (UWWTPs), facilities mainly powered by fossil fuels. The opportunity to integrate renewable sources of energy into the energy-intensive UWWTPs holds great promise towards decarbonization of the sector. In this context, the energy harvested from a Salinity Gradient (SGE) has attracted great interest in the last decade. This work aims at the analysis of opportunity of implementing integrated processes for water reclamation and SGE recovery in the coastal EU UWWTPs. According to the selection criteria, a total of 281 potential sites located across eighteen coastal countries of the EU have been inventoried attending to the current state of the art. The water reclamation potential has been estimated at 3.7 million m3/day. As a consequence, the environmental burdens of the reclamation process could result in the reduction of 1.5·105 t CO2/year. The Mediterranean region, highly affected by hydrological drought, has proved to be a hot spot for water reclamation, with the highest number of plants inventoried in the study and a predicted potential for SGE harvesting of 60 Wh/m3 of reclaimed water. These results highlight a niche of opportunities to encourage water reclamation, avoid water bodies' degradability due to effluent discharge and the further decarbonization of reclamation processes.

Recycling of nutrient medium to improve productivity in large-scale microalgal culture using a hybrid electrochemical water treatment system

Recycling and reusing of nutrient media in microalgal cultivation are important strategies to reduce water consumption and nutrient costs. However, these approaches have limitations, e.g., a decrease in biomass production, (because as reused media can inhibit biomass growth). To address these limitations, we applied a novel membrane filtration‒electrolysis‒ultraviolet hybrid water treatment method capable of laboratory-to-large-scale operation to increase biomass productivity and enable nutrient medium disinfection and recycling. In laboratory-scale experiments, electrolysis effectively remove the biological contaminants from the spent nutrient medium, resulting in a high on-site removal efficiency of dissolved organic carbon (DOC; 80.3 ± 5 %) and disinfection (99.5 ± 0.2 %). Compared to the results for the recycling of nutrient medium without water treatment, electrolysis resulted in a 1.5-fold increase in biomass production, which was attributable to the removal of biological inhibitors from electrochemically produced oxidants (mainly OCl-). In scaled-up applications, the hybrid system improved the quality of the recycled nutrient medium, with 85 ± 2 % turbidity removal, 75 ± 3 % DOC removal, and 99.5 ± 2 % disinfection efficiency, which was beneficial for biomass growth by removing biological inhibitors. After applying the hybrid water treatment method, we achieved a Spirulina biomass production of 0.47 ± 0.03 g L-1, similar to that obtained using a fresh medium (0.53 ± 0.02 g L-1). The on-site disinfection process described herein is practical and offers a cost-saving and environmental friendly alternative for nutrient medium recycling and reusing water in mass and sustainable cultivation of microalgae.

A Strategy for Power Density Amelioration of Capacitive Reverse Electrodialysis Systems with a Single Membrane

Blue energy refers to the osmotic energy released while combining solutions of different salinity. Recently, single-membrane-based capacitive reverse electrodialysis cells were developed for blue energy harvesting. The performance of these cells is limited by the low ion-electron flux transfer efficiency of the capacitive electrodes in the current operating regimes. To optimize it, we point out an original boosting strategy of using a secondary voltage source E0 placed in series with the capacitive concentration cell. The net recovered power is defined as the difference between the power dissipated in the load resistor and the power supplied by the secondary voltage. Experimental results indicate a maximum power density of 5.26 W·m-2 (where the salinity difference is 0.17 and 5.13 M), which corresponds to a 59.8% increase compared with its power density of 3.29 W·m-2 without boosting strategy. A good agreement on power density is reached for theoretical simulations and experimental results. Influential factors are systematically studied to further reveal the boosting strategy.

Robust Cellulose Nanocrystal-Based Self-Assembled Composite Membranes Doped with Polyvinyl Alcohol and Graphene Oxide for Osmotic Energy Harvesting

Osmotic energy from the salinity gradients represents a promising energy resource with stable and sustainable characteristics. Nanofluidic membranes can be considered as powerful alternatives to the traditional low-performance ion exchange membrane to achieve high-efficiency osmotic energy harvesting. However, the development of a highly efficient and easily scalable core membrane component from low-cost raw materials remains challenging. Here, a composite membrane based on the self-assembly of cellulose nanocrystals (CNCs) with polyvinyl alcohol (PVA) and graphene oxide (GO) nanoflakes as additives is developed to provide a solution. The introduction of soft PVA polymer significantly improves the mechanical strength and water stability of the composite membrane by forming a nacre-like structure. Benefiting from the abundant negative charges of CNC nanorods and GO nanoflakes and the generated network nanochannels, the composite membrane demonstrates a good cation-selective transport capacity, thus contributing to an optimal osmotic energy conversion of 6.5 W m-2 under a 100-fold salinity gradient and an exemplary stability throughout 25 consecutive days of operation. This work provides an option for the development of nanofluidic membranes that can be easily produced on a large scale from well-resourced and sustainable biomass materials for high-efficiency osmotic energy conversion.

Tuning Surface Molecular Design of Porous Carbon for Blue Energy Harvesting

Capacitive mixing is a promising blue energy technology due to its membrane-free electricity generation and long electrode life cycle. However, because of limited performance, existing systems do not lend themselves to practical implementation. Although it is a crucial factor directly influencing electrode behavior, surface chemistry has largely been overlooked in capacitive mixing. Here, we show that manipulating surface functionalization alone can tune the responses of electrodes to produce a high voltage rise without altering the pore structure of the electrodes. Our findings reveal that the spontaneous electrode potential of a surface-modified carbon electrode shifts negatively proportional to the surface charge due to the surface groups, which explains why and how manipulating the surface chemistry can improve the power generation capacity. Using electrodes fabricated with identical activated carbon material but with different surface treatments, we have achieved a remarkably high power density of 166 mW/m² delivered to an electrical load under a 0.6 M to 0.01 M salinity gradient, with the total power generated of 225 mW/m². The corresponding volumetric power densities were 0.88 kW/m³ net and 1.17 kW/m³ total. The volumetric power density of our prototype is comparable to or better than those of prevailing membrane technologies, such as pressure retarded osmosis and reverse electrolysis, whose volumetric power density values are 1.1 kW/m³ and 0.16 kW/m³, respectively. In the seawater stage, the net power density reached 432 mW/m² or 2.3 kW/m³. Such performance far exceeds existing membrane-free systems, with the highest reported power density of 65 mW/m² under a 0.5 M to 0.02 M salinity gradient (121 mW/m² in this work). The device demonstrated unparalleled durability, maintaining 90% of the maximum energy capacity after 54,000 charge-discharge cycles.

Interfacial Super-Assembly of Intertwined Nanofibers toward Hybrid Nanochannels for Synergistic Salinity Gradient Power Conversion

Capturing the abundant salinity gradient power into electric power by nanofluidic systems has attracted increasing attention and has shown huge potential to alleviate the energy crisis and environmental pollution problems. However, not only the imbalance between permeability and selectivity but also the poor stability and high cost of traditional membranes limit their scale-up realistic applications. Here, intertwined "soft-hard" nanofibers/tubes are densely super-assembled on the surface of anodic aluminum oxide (AAO) to construct a heterogeneous nanochannel membrane, which exhibits smart ion transport and improved salinity gradient power conversion. In this process, one-dimensional (1D) "soft" TEMPO-oxidized cellulose nanofibers (CNFs) are wrapped around "hard" carbon nanotubes (CNTs) to form three-dimensional (3D) dense nanochannel networks, subsequently forming a CNF-CNT/AAO hybrid membrane. The 3D nanochannel networks constructed by this intertwined "soft-hard" nanofiber/tube method can significantly enhance the membrane stability while maintaining the ion selectivity and permeability. Furthermore, benefiting from the asymmetric structure and charge polarity, the hybrid nanofluidic membrane displays a low membrane inner resistance, directional ionic rectification characteristics, outstanding cation selectivity, and excellent salinity gradient power conversion performance with an output power density of 3.3 W/m². Besides, a pH sensitive property of the hybrid membrane is exhibited, and a higher power density of 4.2 W/m² can be achieved at a pH of 11, which is approximately 2 times more compared to that of pure 1D nanomaterial based homogeneous membranes. These results indicate that this interfacial super-assembly strategy can provide a way for large-scale production of nanofluidic devices for various fields including salinity gradient energy harvesting.

Design of a Reverse Electrodialysis Plant for Salinity Gradient Energy Extraction in a Coastal Wastewater Treatment Plant

The chemical potential difference at the discharge points of coastal Wastewater Treatment Plants (WWTPs) uncovers the opportunity to harness renewable salinity gradient energy (SGE). This work performs an upscaling assessment of reverse electrodialysis (RED) for SGE harvesting of two selected WWTPs located in Europe, quantified in terms of net present value (NPV). For that purpose, a design tool based on an optimization model formulated as a Generalized Disjunctive Program previously developed by the research group has been applied. The industrial scale-up of SGE-RED has already proven to be technically and economically feasible in the Ierapetra medium-sized plant (Greece), mainly due to a greater volumetric flow and a warmer temperature. At the current price of electricity in Greece and the up-to-date market cost of membranes of 10 EUR/m², the NPV of an optimized RED plant in Ierapetra would amount to EUR117 thousand operating with 30 RUs in winter and EUR 157 thousand for 32 RUs in summer, harnessing 10.43 kW and 11.96 kW of SGE for the winter and summer seasons, respectively. However, in the Comillas facility (Spain), this could be cost-competitive with conventional alternatives, namely coal or nuclear power, under certain conditions such as lower capital expenses due to affordable membrane commercialization (4 EUR/m²). Bringing the membrane price down to 4 EUR/m² would place the SGE-RED's Levelized Cost of Energy in the range of 83 EUR/MWh to 106 EUR/MWh, similar to renewable sources such as solar PV residential rooftops.

Comparison of Energy Efficiency between Atmospheric Batch Pressure-Retarded Osmosis and Single-Stage Pressure-Retarded Osmosis

Batch pressure-retarded osmosis (PRO) with varied-pressure and multiple-cycle operation using a pressurized variable-volume tank has been proposed as a high-efficiency osmotic energy harvesting technology, but it suffers scalability constraints. In this study, a more scalable batch PRO, namely, atmospheric batch PRO (AB-PRO), was proposed, utilizing an atmospheric tank to receive and store the intermediate diluted draw solution (DS) and a pressure exchanger to recover the pressure energy from the diluted DS before being recycled into the tank. Its performance was further compared with single-stage PRO (SS-PRO) at different flow schemes via analytic models. The results show that the AB-PRO with an infinitesimal per-cycle water recovery (r) approaches the thermodynamic maximum energy production under ideal conditions, outperforming the SS-PRO with lower efficiencies caused by under-pressurization (UP). However, when considering inefficiencies, a ~40% efficiency reduction was observed in AB-PRO owing to UP and entropy generation as the optimal r is no-longer infinitesimal. Nonetheless, AB-PRO is still significantly superior to SS-PRO at low water recoveries (R) and maintains a stable energy efficiency at various R, which is conducive to meeting the fluctuating demand in practice by flexibly adjusting R. Further mitigating pressure losses and deficiencies of energy recovery devices can significantly improve AB-PRO performance.

Fluidics for energy harvesting: from nano to milli scales

A large amount of untapped energy sources surrounds us. In this review, we summarize recent works of water-based energy harvesting systems with operation scales ranging from miniature systems to large scale attempts. We focus particularly on the triboelectric energy, which is produced when a liquid and a solid come into contact, and on the osmotic energy, which is released when salt water and fresh water are mixed. For both techniques we display the state of the art understanding (including electrical charge separation, electro-osmotic currents and induced currents) and the developed devices. A critical discussion of present works confirms the significant progress of these water-based energy harvesting systems in all scales. However, further efforts in efficiency and performance amelioration are expected for these technologies to accelerate the industrialization and commercialization procedure.

Review of Seawater Fiber Optic Salinity Sensors Based on the Refractive Index Detection Principle

This paper presents a systematic review of the research available on salinity optic fiber sensors (OFSs) for seawater based on the refractive index (RI) measurement principle for the actual measurement demand of seawater salinity in marine environmental monitoring, the definition of seawater salinity and the correspondence between the seawater RI and salinity. To further investigate the progress of in situ measurements of absolute salinity by OFSs, the sensing mechanisms, research progress and measurement performance indices of various existing fiber optic salinity sensors are summarized. According to the Thermodynamic Equation of Seawater-2010 (TEOS-10), absolute salinity is recommended for sensor calibration and measurement. Comprehensive domestic and international research progress shows that fiber-optic RI sensors are ideal for real-time, in situ measurement of the absolute salinity of seawater and have excellent potential for application in long-term in situ measurements in the deep ocean. Finally, based on marine environmental monitoring applications, a development plan and the technical requirements of salinity OFSs are proposed to provide references for researchers engaged in related industries.

Power Generation Performance of Reverse Electrodialysis (RED) Using Various Ion Exchange Membranes and Power Output Prediction for a Large RED Stack

Reverse electrodialysis (RED) power generation using seawater (SW) and river water is expected to be a promising environmentally friendly power generation system. Experiments with large RED stacks are needed for the practical application of RED power generation, but only a few experimental results exist because of the need for large facilities and a large area of ion-exchange membranes (IEMs). In this study, to predict the power output of a large RED stack, the power generation performances of a lab-scale RED stack (40 membrane pairs and 7040 cm² total effective membrane area) with several IEMs were evaluated. The results were converted to the power output of a pilot-scale RED stack (299 membrane pairs and 179.4 m² total effective membrane area) via the reference IEMs. The use of low-area-resistance IEMs resulted in lower internal resistance and higher power density. The power density was 2.3 times higher than that of the reference IEMs when natural SW was used. The net power output was expected to be approximately 230 W with a pilot-scale RED stack using low-area-resistance IEMs and natural SW. This value is one of the indicators of the output of a large RED stack and is a target to be exceeded with further improvements in the RED system.

Chelating agents for diluted geothermal brine reinjection

"Blue energy" could be produced by exploiting the large salinity gradient between geothermal fluids and freshwater through a SaltPower system. This study is an attempt to select the most favorable chemicals to avoid injectivity issues when a diluted geothermal fluid resulting from the SaltPower system is returned to the reservoir. Three synthetic chelating agents (oxalic acid, EDTA, and EDDS) and one natural (humic acid) were evaluated through speciation simulations and isothermal titration calorimetry (ITC) experiments. The speciation simulation results indicate that the degree of complexing is highly dependent on pH and chelating agent type. The ITC experiments show that the total heat for the formation of soluble metal-ligand complexes in the rock + geothermal brine system follows: EDTA > EDDS > oxalic acid > humic acid. The simulations and calorimetry results suggest that EDTA could be used to avoid the precipitation of Fe(III) oxides and other minerals (e.g., calcite and dolomite) inside the porous media upon the reinjection of diluted geothermal brine coming from SaltPower electricity production.

Electrochemical Methods for Water Purification, Ion Separations, and Energy Conversion

Agricultural development, extensive industrialization, and rapid growth of the global population have inadvertently been accompanied by environmental pollution. Water pollution is exacerbated by the decreasing ability of traditional treatment methods to comply with tightening environmental standards. This review provides a comprehensive description of the principles and applications of electrochemical methods for water purification, ion separations, and energy conversion. Electrochemical methods have attractive features such as compact size, chemical selectivity, broad applicability, and reduced generation of secondary waste. Perhaps the greatest advantage of electrochemical methods, however, is that they remove contaminants directly from the water, while other technologies extract the water from the contaminants, which enables efficient removal of trace pollutants. The review begins with an overview of conventional electrochemical methods, which drive chemical or physical transformations via Faradaic reactions at electrodes, and proceeds to a detailed examination of the two primary mechanisms by which contaminants are separated in nondestructive electrochemical processes, namely electrokinetics and electrosorption. In these sections, special attention is given to emerging methods, such as shock electrodialysis and Faradaic electrosorption. Given the importance of generating clean, renewable energy, which may sometimes be combined with water purification, the review also discusses inverse methods of electrochemical energy conversion based on reverse electrosorption, electrowetting, and electrokinetic phenomena. The review concludes with a discussion of technology comparisons, remaining challenges, and potential innovations for the field such as process intensification and technoeconomic optimization.

Sustainable energy harvesting and on-site disinfection of natural seawater using reverse electrodialysis

Seawater is a cost-effective and abundant electrolyte used as an electrode rinse solution to enable optimum utilization of reverse electrodialysis (RED). However, it is associated with several limitations, including the use of precious electrode materials, and its long-term stability must be addressed prior to its application in the field of seawater technology. In this context, a novel RED based on carbon electrodes was designed, and the experimental conditions were optimized for maximizing the harvesting of energy with aquaculture wastewater disinfection and recycling. The power obtained by RED, with a current density of 30 A/m² and a flow rate of 424 mL/min, designed by response surface methodology, was in good agreement with the predicted maximum power density (0.64 W/m²). The treatment was sustainable, mainly due to an anodic reaction of electro-generated sodium hypochlorite (NaOCl) under natural conditions, which afforded a high disinfection efficiency (above 99.5 ± 0.2% within 1 min under continuous flow (pH 8)), even under real seawater conditions and in aquaculture wastewater. Simultaneously, a stable power of 0.1 ± 0.03 W (0.25 ± 0.07 W/m²) generated a reasonable specific energy (within 0.02 kWh/m³). Inorganic fouling was efficiently suppressed using a surface-modified carbon cathode for 680 h. Thus, the on-site seawater disinfection by RED described herein is practically feasible and could offer a sustainable and energy-efficient alternative to seawater recycling.

Modern biophysical view of electromagnetic processes of the phenomenon of life of living biological systems as a promising basis for the development of complex medicine: the role of cell membranes

The results of a theoretical study of the role of cell membranes in electromagnetic generation and in the process of realizing the phenomenon of life are presented in the article. The aim of the theoretical study was to summarize the existing scientific physical and biological knowledge of modern science about the electromagnetic processes of the phenomenon of life at the cellular level in order to deepen the fundamental knowledge of complex medicine. This study is a fragment of research work on “The development of algorithms and technologies for implementing a Healthy Lifestyle in patients with Noncommunicable Diseases based on the study of functional status” (state registration number 0121U108237: UDC 613 616-056-06: 616.1/9-03). General scientific methods and theoretical methods were used in this theoretical study. The main conclusions of the theoretical study were made as follows: 1) Cell membranes can be considered one of the main morphological structures of electromagnetic generation at the cellular level. 2) Cell viability is ensured by electromagnetic generation and electromagnetic generation of cells can be considered as a separate important function of membranes in addition to those already defined, as it provides signaling. 3) The end result of electromagnetic generation of cell membranes and all molecules of the cell is its own electromagnetic fields, which have a millimeter wavelength range with a frequency of 1010-1011 Hz and they are a quantum mechanical result of electromagnetic generations, perform the information-energy function in intercellular interaction in vivo.

Decoupled aqueous batteries using pH-decoupling electrolytes

Aqueous batteries have been considered as the most promising alternatives to the dominant lithium-based battery technologies because of their low cost, abundant resources and high safety. The output voltage of aqueous batteries is limited by the narrow stable voltage window of 1.23 V for water, which theoretically impedes further improvement of their energy density. However, the pH-decoupling electrolyte with an acidic catholyte and an alkaline anolyte has been verified to broaden the operating voltage window of the aqueous electrolyte to over 3 V, which goes beyond the voltage limitations of the aqueous batteries, making high-energy aqueous batteries possible. In this Review, we summarize the latest decoupled aqueous batteries based on pH-decoupling electrolytes from the perspective of ion-selective membranes, competitive redox couples and potential battery prototypes. The inherent defects and problems of these decoupled aqueous batteries are systematically analysed, and the critical scientific issues of this battery technology for future applications are discussed.

Microscopic Simulations of Electrochemical Double-Layer Capacitors

Electrochemical double-layer capacitors (EDLCs) are devices allowing the storage or production of electricity. They function through the adsorption of ions from an electrolyte on high-surface-area electrodes and are characterized by short charging/discharging times and long cycle-life compared to batteries. Microscopic simulations are now widely used to characterize the structural, dynamical, and adsorption properties of these devices, complementing electrochemical experiments and in situ spectroscopic analyses. In this review, we discuss the main families of simulation methods that have been developed and their application to the main family of EDLCs, which include nanoporous carbon electrodes. We focus on the adsorption of organic ions for electricity storage applications as well as aqueous systems in the context of blue energy harvesting and desalination. We finally provide perspectives for further improvement of the predictive power of simulations, in particular for future devices with complex electrode compositions.

One Porphyrin Per Chain Self-Assembled Helical Ion-Exchange Channels for Ultrahigh Osmotic Energy Conversion

Ion-exchange membranes (IEMs) convert osmotic energy into electricity when embedded in a reverse electrodialysis cell. IEMs with both high permselectivity and ionic conductivity are highly needed to increase the energy conversion efficiency. The ionic conductivity can be improved by increasing the content of immobile charge carriers, but it is always accompanied by undesirable permselectivity decrease due to excess swelling. Until now, breaking the permselectivity-conductivity tradeoff still has remained a challenge. Here, we demonstrate a membrane with the least ion-exchange capacity (∼10^-2 mequiv g^-1), generating an ultrahigh power density of 19.3 W m^-2 at a 50-fold concentration ratio. The membrane is made of a porphyrin-core four-star block copolymer (p-BCP), forming the high-density helical porphyrin channels (∼10¹¹ cm^-2) under the synergistic effect of BCP self-assembly and porphyrin π-π stacking. The porphyrin channel shows high Cl^- selectivity and high conductivity, benefiting high-performance osmotic energy conversion. This economic and facile membrane design strategy provides a promising approach to developing a new generation of IEMs.

Focus on using nanopore technology for societal health, environmental, and energy challenges

With an increasing global population that is rapidly ageing, our society faces challenges that impact health, environment, and energy demand. With this ageing comes an accumulation of cellular changes that lead to the development of diseases and susceptibility to infections. This impacts not only the health system, but also the global economy. As the population increases, so does the demand for energy and the emission of pollutants, leading to a progressive degradation of our environment. This in turn impacts health through reduced access to arable land, clean water, and breathable air. New monitoring approaches to assist in environmental control and minimize the impact on health are urgently needed, leading to the development of new sensor technologies that are highly sensitive, rapid, and low-cost. Nanopore sensing is a new technology that helps to meet this purpose, with the potential to provide rapid point-of-care medical diagnosis, real-time on-site pollutant monitoring systems to manage environmental health, as well as integrated sensors to increase the efficiency and storage capacity of renewable energy sources. In this review we discuss how the powerful approach of nanopore based single-molecule, or particle, electrical promises to overcome existing and emerging societal challenges, providing new opportunities and tools for personalized medicine, localized environmental monitoring, and improved energy production and storage systems.

Impact of Reservoir Heterogeneity on Diluted Geothermal Brine Reinjection

Many geothermal plants have been shut down due to reinjection problems with the heat-depleted brine. In Denmark, only one out of three plants that extract heat from a geothermal fluid distributed to the district heating system is still working. In general, the large salinity of heat-depleted geothermal brines can be used to produce electricity with the help of turbines and generators through an osmotic power unit known as a SaltPower plant. Harnessing more energy out of the reinjection of geothermal brines is feasible without compromising the overall reservoir assurance when the iron is kept under control. This study is an attempt to determine the feasibility of the reinjection of a diluted geothermal brine with ethylenediaminetetraacetic acid (EDTA) into homogeneous and heterogeneous sandstone rocks. The results from the coreflooding experiments show an improvement in the rock properties both in porosity and permeability for homogeneous and heterogeneous rocks. EDTA not only avoids the precipitation of Fe(III) oxides inside the porous media but can also be used for scale removal and matrix acidizing in geothermal reservoirs.

Bio-Inspired Salinity-Gradient Power Generation With UiO-66-NH2 Metal-Organic Framework Based Composite Membrane

Salinity-gradient directed osmotic energy between seawater and river water has been widely considered as a promising clean and renewable energy source, as there are numerous river estuaries on our planet. In the past few decades, reverse electrodialysis (RED) technique based on cation-selective membranes has been used as the key strategy to convert osmotic energy into electricity. From this aspect, developing high-efficiency anion-selective membranes will also have great potential for capturing osmotic energy, however, remains systematically unexplored. In nature, electric eels can produce electricity from ionic gradients by using their “sub-nanoscale” protein ion channels to transport ions selectively. Inspired by this, here we developed a UiO-66-NH₂ metal-organic framework (MOF) based anion-selective composite membrane with sub-nanochannels, and achieved high-performance salinity-gradient power generation by mixing artificial seawater (0.5 M NaCl) and river water (0.01 M NaCl). The UiO-66-NH₂ metal-organic framework based composite membranes can be easily and economically fabricated with dense structure and long-term working stability in saline, and its performance of power generation can also be adjusted by pH to enhance the surface charge density of the MOF sub-nanochannels. This study will inspire the exploitation of MOFs for investigating the sub-nanochannel directed high-performance salinity-gradient energy harvesting systems based on anion-selective ion transport.

Strategically Altered Fluorinated Polymer at Nanoscale for Enhancing Proton Conduction and Power Generation from Salinity Gradient

Reverse electrodialysis (RED) generates power directly by transforming salinity gradient into electrical energy. The ion transport properties of the ion-exchange membranes need to be investigated deeply to improve the limiting efficiencies of the RED. The interaction between “counterions” and “ionic species” in the membrane requires a fundamental understanding of the phase separation process. Here, we report on sulfonated poly(vinylidene fluoride-co-hexafluoropropylene)/graphitic carbon nitride nanocomposites for RED application. We demonstrate that the rearrangement of the hydrophilic and hydrophobic domains in the semicrystalline polymer at a nanoscale level improves ion conduction. The rearrangement of the ionic species in polymer and “the functionalized nanosheet with ionic species” enhances the proton conduction in the hybrid membrane without a change in the structural integrity of the membrane. A detailed discussion has been provided on the membrane nanostructure, chemical configuration, structural robustness, surface morphology, and ion transport properties of the prepared hybrid membrane. Furthermore, the RED device was fabricated by combining synthesized cation exchange membrane with commercially available anion exchange membrane, NEOSEPTA, and a maximum power density of 0.2 W m⁻² was successfully achieved under varying flow rates at the ambient condition.

Effect of osmotic ballast properties on the performance of a concentration gradient battery

A concentration gradient battery (CGB) is an energy storage system comprised of a series of concentrated and dilute salt solution compartments, separated by ion exchange membranes (IEMs). The battery is charged by electrodialysis (ED), which increases the concentration gradient between these solutions, and discharged by reverse electrodialysis (RED), which allows these solutions to mix. In both ED and RED, water moves by osmosis from dilute to concentrated compartments, reducing the CGB faradaic and energy efficiency. A promising approach to mitigate osmosis is to use an osmotic ballast in the dilute solution to balance the osmotic pressure and reduce faradaic energy losses. The objective of this study was to investigate the impact of ballast properties (i.e., size, structure, end-group) on the faradaic and round-trip efficiency of the CGB. To accomplish this objective, we tested seven sugar and five glycol compounds as osmotic ballasts in a closed-loop cell. Results show that ballasts with high molecular weight generally resulted in higher faradaic efficiency and lower water transport compared with low molecular weight ballasts. Data also indicates that ballast with a cyclic structure (instead of linear), non-planar structure (instead of planar), and lower number of methyl end-groups led to lower water transport. Of all ballasts tested, sucrose performed best in terms of reducing non-ideal water transport (by 109%) and enhancing both faradaic and round-trip efficiencies (from 47.4% to 77.7% and 25.5% to 38.1%, respectively) compared with the non-ballasted CGB. Our results contribute to fundamental understanding of the impact of solute properties on water and small organic molecule transport in ion exchange membranes and indicate that ballasted CGBs can be further improved through development of optimized ballasts and selection of optimum membrane-ballast pairs. The improved understanding of ballast impact on CGB performance could be used for evaluation of potential ballast benefits in other membrane-based systems that may be impacted by osmosis such as the acid-base flow battery, waste heat recovery using RED, ED purification processes, osmotically assisted processes, and redox flow batteries.

Response of salinity gradient power generation to inflow mode and temperature difference by reverse electrodialysis

Sustainable utilization has been becoming the core idea of concentrated seawater disposal, which makes the harvest of salinity gradient power based on reverse electrodialysis (RED) become one of the important ways. As the important factors affecting RED performance, different flow orientations along the membrane and solution temperature have been studied in the previous researches. However, there are still some details that need to be clarified. In this study, the inflow mode was further detailed investigated. The results showed that after eliminating the interference of bubbles in the counter-current, the co-current was still better than the counter-current; when the solution of HCC (high concentration compartment) and LCC (low concentration compartment) was circulated for 3 h, the concentration of concentrated seawater discharge liquid was reduced by 6.93%, which was conducive to reducing the negative impact on the marine ecological environment. Meanwhile, the response of salinity gradient power generation to temperature difference was that high temperature had a positive effect on power density, and the order was both the HCC and LCC (0.44 W m^-2) > LCC (0.42 W m^-2) > HCC (0.39 W m^-2). Although the RED performance was more sensitive to the temperature rise of LCC, the positive temperature difference between HCC and LCC is a more practical advantage because the temperature of concentrated seawater in HCC is usually high. These new observations could provide supports for the industrial development of RED in generating electricity economically and reducing the negative environmental impact of concentrated seawater.