Synthesis of Nonaggregating HgTe Colloidal Quantum Dots and the Emergence of Air-Stable n-Doping

Long-Wave Infrared HgTe Quantum Dot Photoconductors with Optical Enhancement

HgTe quantum dots are studied for long-wave infrared detection using interband absorption. The optical constant, photoluminescence, mobility, carrier lifetime, and doping are measured. Simple photoconductors are made as films on interdigitated electrodes, and the best performance is obtained with intrinsic films of quasi-spherical HgTe particles that have been cast from polar inks and exposed to HgCl2 solutions. As the temperature is lowered to 85 K, the photoresponse extends past 8 μm. The performance is limited by a low absorption coefficient near the absorption edge and by a very short exciton lifetime as determined by the photoluminescence quantum yield of 10-5. A metal-insulator-metal structure combined with gold nanoantennas and a 100 nm thick HgTe dot film gives a ∼20-fold increase in responsivity and detectivity for a peak resonance at 8.5 μm at 85 K. The best detectivity is 1.47 × 1010 Jones at 0.8 V bias, 25 kHz frequency, and TE polarization. An external quantum efficiency (EQE) of 12.5% is also achieved at a higher bias.

Colloidal quantum dots as solution-based nanomaterials for infrared technologies

This review focuses on recent progress of wet-chemistry-based synthesis methods for infrared (IR) colloidal quantum dots (CQD), semiconductor nanocrystals with a narrow energy bandgap that absorbs and/or emits IR photos covering from 0.7 to 25 micrometers. The sections of the review are colloidal synthesis, precursor reactivity, cation exchange, doping and de-doping, surface passivation and ligand exchange, intraband transitions, quenching and purification, and future directions. The colloidal synthesis section is organized based on precursors employed: toxic substances as mercury- and lead-based metals and non-toxic substances as indium- and silver-based metal precursors. CQDs are prepared by wet-chemical methods that offer advantages such as precise spectral tunability by adjusting particle size or particle composition, easy fabrication and integration of solution-based CQDs (as inks) with complementary metal-oxide-semiconductors, reduced cost of material manufacturing, and good performances of IR CQD-made optoelectronic devices for non-military applications. These advantages may allow facile and materials' cost-reduced device fabrications that make CQD based IR technologies accessible compared to optoelectronic devices utilizing epitaxially grown semiconductors. However, precursor libraries should be advanced to improve colloidal IR quantum dot synthesis, enabling CQD based IR technologies available to consumer electronics. As the attention of academia and industry to CQDs continue to proliferate, the progress of precursor chemistry for IR CQDs could be rapid.

Short-Wave Infrared Detection and Imaging Employing Size-Customized HgTe Nanocrystals

HgTe nanocrystals (NCs) possess advantages including tunable infrared absorption spectra, solution processability, and low fabrication costs, offering new avenues for the advancement of next-generation infrared detectors. In spite of great synthetic advances, it remains essential to achieve customized synthesis of HgTe NCs in terms of industrial applications. Herein, by taking advantage of a high critical nucleation concentration of HgTe NCs, a continuous-dropwise (CD) synthetic approach that features the addition of the anion precursors in a feasible drop-by-drop fashion is demonstrated. The slow reaction dynamics enable size-customized synthesis of HgTe NCs with sharp band tails and wide absorption range fully covering the short- and mid-infrared regions. More importantly, the intrinsic advantages of CD process ensure high-uniformity and scale-up synthesis from batch to batch without compromising the excitonic features. The resultant HgTe nanocrystal photodetectors show a high room-temperature detectivity of 8.1 × 1011 Jones at 1.7 µm cutoff absorption edge. This CD approach verifies a robust method for controlled synthesis of HgTe NCs and might have important implications for scale-up synthesis of other nanocrystal materials.

Intraband cascade electroluminescence with weakly n-doped HgTe colloidal quantum dots

Room temperature 6 μm intraband cascade electroluminescence (EL) is demonstrated with lightly n-doped HgTe colloidal quantum dots of ∼8 nm diameter deposited on interdigitated electrodes in a metal-insulator-metal device. With quantum dot films of ∼150 nm thickness made by solid-state-ligand-exchange, the devices emit at 1600 cm-1 (6.25 μm), with a spectral width of 200 cm-1, determined by the overlap of the 1Se-1Pe intraband transition of the quantum dots and the substrate photonic resonance. At the maximum current used of 20 mA, the bias was 30 V, the external quantum efficiency was 2.7%, and the power conversion efficiency was 0.025%. Adding gold nano-antennas between the electrodes broadened the emission and increased the quantum efficiency to 4.4% and the power efficiency to 0.036%. For these films, the doping was about 0.1 electron/dot, the electron mobility was 0.02 cm2 V-1 s-1, and the maximum current density was 0.04 kA cm-2. Higher mobility films made by solution ligand exchange show a 20-fold increase in current density and a 10-fold decrease in EL efficiencies. Electroluminescence with weak doping is interesting for eventually achieving electrically driven stimulated emission, and the requirements for population inversion and lasing are discussed.

In-Synthesis Se-Stabilization Enables Defect and Doping Engineering of HgTe Colloidal Quantum Dots

Colloidal Quantum Dots (CQDs) of mercury telluride (HgTe) hold particular appeal for infrared photodetection due to their widely tunable infrared absorption and good compatibility with silicon electronics. While advances in surface chemistry have led to improved CQD solids, the chemical stability of HgTe material is not fully emphasized. In this study, it is aimed to address this issue and identifies a Se-stabilization strategy based on the surface coating of Se on HgTe CQDs via engineering in the precursor reactivity. The presence of Se-coating enables HgTe CQDs with improved colloidal stability, passivation, and enhanced degree of freedom in doping tuning. This enables the construction of optimized p-i-n HgTe CQD infrared photodetectors with an ultra-low dark current 3.26 × 10-6 A cm⁻2 at -0.4 V and room-temperature specific detectivity of 5.17 × 1011 Jones at wavelength ≈2 um, approximately one order of magnitude improvement compared to that of the control device. The stabilizing effect of Se is well preserved in the thin film state, contributing to much improved device stability. The in-synthesis Se-stabilization strategy highlights the importance of the chemical stability of materials for the construction of semiconductor-grade CQD solids and may have important implications for other high-performance CQD optoelectronic devices.

Understanding the Growth Mechanism of HgTe Colloidal Quantum Dots through Bilateral Injection

As potential low-cost alternatives of traditional bulk HgCdTe crystals, HgTe colloidal quantum dots (CQDs) synthesized through reactions between HgCl2 and trioctylphosphine-telluride in hot oleylamine have shown promising performances in mid-wave infrared photodetectors. Tetrapodic or tetrahedral HgTe CQDs have been obtained by tuning the reaction conditions such as temperature, reaction time, concentrations, and ratios of the two precursors. However, the principles governing the growth dynamics and the mechanism behind the transitions between tetrapodic and tetrahedral HgTe CQDs have not been sufficiently understood. In this work, synthesis of HgTe CQDs through bilateral injection is introduced to study the growth mechanism. It suggests that tetrahedral HgTe CQDs usually result from the breaks of tetrapodic HgTe CQDs after their legs grow thick enough. The fundamental factor determining whether the growth makes their legs longer or thicker is the effective concentration of the Te precursor during the growth, rather than temperature, Hg-rich environment, or reactivity of precursors. A chemical model is proposed to illustrate the principles governing the growth dynamics, which provides valuable guidelines for tuning the material properties of HgTe CQDs according to the needs of applications.

Obviating Ligand Exchange Preserves the Intact Surface of HgTe Colloidal Quantum Dots and Enhances Performance of Short Wavelength Infrared Photodetectors

A large volume, scalable synthesis procedure of HgTe quantum dots (QDs) capped initially with short-chain conductive ligands ensures ligand exchange-free and simple device fabrication. An effective n- or p-type self-doping of HgTe QDs is achieved by varying cation-anion ratio, as well as shifting the Fermi level position by introducing single- or double-cyclic thiol ligands, that is, 2-furanmethanethiol (FMT) or 2,5-dimercapto-3,4-thiadiasole (DMTD) in the synthesis. This allows for preserving the intact surface of the HgTe QDs, thus ensuring a one order of magnitude reduced surface trap density compared with HgTe subjected to solid-state ligand exchange. The charge carrier diffusion length can be extended from 50 to 90 nm when the device active area consists of a bi-layer of cation-rich HgTe QDs capped with DMTD and FMT, respectively. As a result, the responsivity under 1340 nm illumination is boosted to 1 AW-1 at zero bias and up to 40 AW-1 under -1 V bias at room temperature. Due to high noise current density, the specific detectivity of these photodetectors reaches up to 1010 Jones at room temperature and under an inert atmosphere. Meanwhile, high photoconductive gain ensures a rise in the external quantum efficiency of up to 1000% under reverse bias.

Uncooled High Detectivity Mid-Infrared Photoconductor Using HgTe Quantum Dots and Nanoantennas

Using a metal/insulator/metal (MIM) structure with a gold nanoantenna array made by electron beam lithography, the responsivity of a HgTe colloidal quantum dot film is enhanced in the mid-infrared. Simulations indicate that the spatially averaged peak spectral absorption of an 80 nm film is 60%, enhanced 23-fold compared to that of the same film on a bare sapphire substrate. The field intensity enhancement is focused near the antenna tips, being 20-fold 100 nm away, which represents only 1% of the total area and up to 1000-fold at the tips. The simulated polarized absorption spectra are in good agreement with the experiments, with a strong resonance around 4 μm. A responsivity of 0.6 A/W is obtained at a 1 V bias. Noise measurements separate the 1/f noise from the generation-recombination white noise and give a spatially averaged photoconductive gain of 0.3 at 1 V bias. The spatially averaged peak detectivity is improved 15-fold compared to the same film on a sapphire substrate without an MIM structure. The experimental peak detectivity reaches 9 × 109 Jones at 2650 cm-1 and 80 kHz, decreasing at lower frequencies. The MIM structure also enhances the spatially averaged peak photoluminescence of the CQD film by 16-fold, which is a potential Purcell enhancement. The good agreement between simulations and measurements confirms the viability of lithographically designed nanoantenna structures for vastly improving the performance of mid-IR colloidal quantum dot photoconductors. Further improvements will be possible by matching the optically enhanced and current collection areas.

Long-Range Hot-Carrier Transport in Topologically Connected HgTe Quantum Dots

The utilization of hot carriers as a means to surpass the Shockley-Queasier limit represents a promising strategy for advancing highly efficient photovoltaic devices. Quantum dots, owing to their discrete energy states and limited multi-phonon cooling process, are regarded as one of the most promising materials. However, in practical implementations, the presence of numerous defects and discontinuities in colloidal quantum dot (CQD) films significantly curtails the transport distance of hot carriers. In this study, the harnessing of excess energies from hot-carriers is successfully demonstrated and a world-record carrier diffusion length of 15 µm is observed for the first time in colloidal systems, surpassing existing hot-carrier materials by more than tenfold. The observed phenomenon is attributed to the specifically designed honeycomb-like topological structures in a HgTe CQD superlattice, with its long-range periodicity confirmed by High-Resolution Transmission Electron Microscopy(HR-TEM), Selected Area Electron Diffraction(SAED) patterns, and low-angle X-ray diffraction (XRD). In such a superlattice, nonlocal hot carrier transport is supported by three unique physical properties: the wavelength-independent responsivity, linear output characteristics and microsecond fast photoresponse. These findings underscore the potential of HgTe CQD superlattices as a feasible approach for efficient hot carrier collection, thereby paving the way for practical applications in highly sensitive photodetection and solar energy harvesting.

Tex Se1-x Photodiode Shortwave Infrared Detection and Imaging

Short-wave infrared detectors are increasingly important in the fields of autonomous driving, food safety, disease diagnosis, and scientific research. However, mature short-wave infrared cameras such as InGaAs have the disadvantage of complex heterogeneous integration with complementary metal-oxide-semiconductor (CMOS) readout circuits, leading to high cost and low imaging resolution. Herein, a low-cost, high-performance, and high-stability Te_x Se_{1- x} short-wave infrared photodiode detector is reported. The Te_x Se_{1- x} thin film is fabricated through CMOS-compatible low-temperature evaporation and post-annealing process, showcasing the potential of direct integration on the readout circuit. The device demonstrates a broad-spectrum response of 300-1600 nm, a room-temperature specific detectivity of 1.0 × 10¹⁰ Jones, a -3 dB bandwidth up to 116 kHz, and a linear dynamic range of over 55 dB, achieving the fastest response among Te-based photodiode devices and a dark current density 7 orders of magnitude smaller than Te-based photoconductive and field-effect transistor devices. With a simple Si₃ N₄ packaging, the detector shows high electric stability and thermal stability, meeting the requirements for vehicular applications. Based on the optimized Te_x Se_{1- x} photodiode detector, the applications in material identification and masking imaging is demonstrated. This work paves a new way for CMOS-compatible infrared imaging chips.

Intraband Transition of HgTe Nanocrystals for Long-Wave Infrared Detection at 12 μm

The synthesis of n-doped HgTe colloidal quantum dots was optimized to produce samples with a 1S_e-1P_e intraband transition in the long-wave infrared (8-12 μm). The spin-orbit splitting of 1P_e states places the 1S_e-1P_e1/2 transition around 10 μm. The narrow line width of 130 cm^-1 at 300 K is limited by the size distribution. This narrowing leads to an absorption coefficient about 5 times stronger than is possible with the HgTe CQD interband transition at similar energies. From 300 to 80 K, the intraband transition blueshifts by 90 cm^-1, while the interband transition redshifts by 350 cm^-1. These shifts are assigned to the temperature dependence of the band structure. With ∼2 electrons/dot doping at 80 K, a photoconductive film of 80 nm thickness on a quarter wave reflector substrate showed a detectivity (D*) of ∼10⁷ Jones at 500 Hz in the 8-12 μm range.

Mercury chalcogenide colloidal quantum dots for infrared photodetection: from synthesis to device applications

Commercial infrared (IR) photodetectors based on epitaxial growth inorganic semiconductors, e.g. InGaAs and HgCdTe, suffer from high fabrication cost, poor compatibility with silicon integrated circuits, rigid substrates and bulky cooling systems, which leaves a large development window for the emerging solution-processable semiconductor-based photo-sensing devices. Among the solution-processable semiconductors, mercury (Hg) chalcogenide colloidal quantum dots (QDs) exhibit unique ultra-broad and tuneable photo-responses in the short-wave infrared to far-wave infrared range, and have demonstrated photo-sensing abilities comparable to the commercial products, especially with advances in high operation temperature. Here, we provide a focused review on photodetectors employing Hg chalcogenide colloidal QDs, with a comprehensive summary of the essential progress in the areas of synthesis methods of QDs, property control, device engineering, focus plane array integration, etc. Besides imaging demonstrations, a series of Hg chalcogenide QD photodetector based flexible, integrated, multi-functional applications are also summarized. This review shows prospects for the next-generation low-cost highly-sensitive and compact IR photodetectors based on solution-processable Hg chalcogenide colloidal QDs.

High-operating-temperature mid-infrared photodetectors via quantum dot gradient homojunction

Due to thermal carriers generated by a narrow mid-infrared energy gap, cooling is always necessary to achieve ideal photodetection. In quantum dot (QD), the electron thermal generation should be reduced with quantum confinement in all three dimensions. As a result, there would be a great potential to realize high-operating-temperature (HOT) QD mid-IR photodetectors, though not yet achieved. Taking the advantages of colloidal nanocrystals' solution processability and precise doping control by surface dipoles, this work demonstrates a HOT mid-infrared photodetector with a QD gradient homojunction. The detector achieves background-limited performance with D^* = 2.7 × 10¹¹ Jones on 4.2 μm at 80 K, above 10¹¹ Jones until 200 K, above 10¹⁰ Jones until 280 K, and 7.6 × 10⁹ Jones on 3.5 μm at 300 K. The external quantum efficiency also achieves more than 77% with responsivity 2.7 A/W at zero bias. The applications such as spectrometers, chemical sensors, and thermal cameras, are also approved, which motivate interest in low-cost, solution-processed and high-performance mid-infrared photodetection beyond epitaxial growth bulk photodetectors.

Integrated photodetectors for compact Fourier-transform waveguide spectrometers

Extreme miniaturization of infrared spectrometers is critical for their integration into next-generation consumer electronics, wearables and ultrasmall satellites. In the infrared, there is a necessary compromise between high spectral bandwidth and high spectral resolution when miniaturizing dispersive elements, narrow band-pass filters and reconstructive spectrometers. Fourier-transform spectrometers are known for their large bandwidth and high spectral resolution in the infrared; however, they have not been fully miniaturized. Waveguide-based Fourier-transform spectrometers offer a low device footprint, but rely on an external imaging sensor such as bulky and expensive InGaAs cameras. Here we demonstrate a proof-of-concept miniaturized Fourier-transform waveguide spectrometer that incorporates a subwavelength and complementary-metal-oxide-semiconductor-compatible colloidal quantum dot photodetector as a light sensor. The resulting spectrometer exhibits a large spectral bandwidth and moderate spectral resolution of 50 cm^-1 at a total active spectrometer volume below 100 μm × 100 μm × 100 μm. This ultracompact spectrometer design allows the integration of optical/analytical measurement instruments into consumer electronics and space devices.

Ultra-mild synthesis of nanometric metal chalcogenides using organyl chalcogenide precursors

Bis(trialkylsilyl) monochalcogenides and diorganyl dichalcogenides, (R₃Si)₂E and R₂E₂ (E = S, Se or Te and R = alkyl, aryl or allyl group), have emerged in the past decade as excellent reagents for the synthesis of metal chalcogenide nanoparticles (NPs) and clusters owing to their ability to transfer the chalcogenide anion (E^2-) under ultra-mild conditions and versatility in reacting even with non-conventional metal reagents or being employed in a variety of synthetic methods. In comparison, the related non-silylated diorganyl monochalcogenides R₂E have received attention only recently for the solution phase synthesis of metal chalcogenide NPs. In spite of sharing many similarities, these three families of organyl chalcogenides are different in their coordination ability and decomposition behavior, and therefore in reactivities towards metal reagents. This feature article provides a concise overview on the use of these three families as synthons for the ultralow-temperature synthesis of metal chalcogenide nanomaterials, deliberating their different decomposition mechanisms and critically assessing their advantages for certain applications. More specifically, it discusses their usefulness in (i) affording molecular precursors with different kinetic and thermal stabilities, (ii) isolating reactive intermediates for comprehending the mechanism of molecule-to-nanoparticle transformation and, therefore, achieving fine control over the synthesis, (iii) stabilizing isolable metastable or difficult-to-achieve phases, and (iv) yielding complex ternary nanoparticles with controlled stoichiometry or composites with sensitive materials without modifying the characteristics of the latter. Besides providing a perspective on the low-temperature synthesis of nanomaterials, this overview is expected to assist further progress, particularly in the field of R₂E, leading to interesting materials including metastable ones for new applications.

Mid-Infrared HgTe Colloidal Quantum Dots In-Situ Passivated by Iodide

Today, colloidal quantum dots (CQDs) have received wide attention due to their properties of tunable infrared absorption. For example, HgTe colloidal quantum dots have shown excellent optical absorption (absorption coefficient α > 104 cm−1), spectral absorption tunability covering the entire infrared atmospheric window, and even the terahertz (THz). However, the efficient surface passivation of HgTe CQDs was limited by the highly sterically hindered long-chain organic ligands. Here, we demonstrate a new method to synthesize monodisperse mid-infrared HgTe CQDs, and the preparation process of the Hg precursor solution is optimized. With I− in-situ passivated on the surfaces, the spherical HgTe quantum dots are successfully synthesized with the tunability size from 8 to 15 nm. The noise current density of the photoconductive device is as low as 10−11 A·Hz−1/2 at 130 K with a frequency of 1 Hz.

Room-Temperature Infrared Photodetectors with Zero-Dimensional and New Two-Dimensional Materials

Infrared photodetectors have received much attention for several decades due to their broad applications in the military, science, and daily life. However, for achieving an ideal signal-to-noise ratio and a very fast response, cooling is necessary in those devices, which makes them bulky and costly. Thus, room-temperature infrared photodetectors have emerged as a hot research direction. Novel low-dimensional materials with their easy fabrication and excellent photoelectronic properties provide a possible solution for room-temperature infrared photodetectors. This review aims to summarize the preparation methods and characterization of several low-dimensional materials (PbS, PbSe and HgTe, new two-dimensional materials) with great concern and the room-temperature infrared photodetectors based on them.

Ligand-Engineered HgTe Colloidal Quantum Dot Solids for Infrared Photodetectors

HgTe colloidal quantum dots (CQDs) are promising absorber systems for infrared detection due to their widely tunable photoresponse in all infrared regions. Up to now, the best-performing HgTe CQD photodetectors have relied on using aggregated CQDs, limiting the device design, uniformity and performance. Herein, we report a ligand-engineered approach that produces well-separated HgTe CQDs. The present strategy first employs strong-binding alkyl thioalcohol ligands to enable the synthesis of well-dispersed HgTe cores, followed by a second growth process and a final postligand modification step enhancing their colloidal stability. We demonstrate highly monodisperse HgTe CQDs in a wide size range, from 4.2 to 15.0 nm with sharp excitonic absorption fully covering short- and midwave infrared regions, together with a record electron mobility of up to 18.4 cm² V^-1 s^-1. The photodetectors show a room-temperature detectivity of 3.9 × 10¹¹ jones at a 1.7 μm cutoff absorption edge.

Midwavelength Infrared p-n Heterojunction Diodes Based on Intraband Colloidal Quantum Dots

As an emerging member of the colloidal semiconductor quantum dot materials family, intraband quantum dots are being extensively studied for thermal infrared sensing applications. High-performance detectors can be realized using a traditional p-n junction device design; however, the heavily doped nature of intraband quantum dots presents a new challenge in realizing diode devices. In this work, we utilize a trait uniquely available in a colloidal quantum dot material system to overcome this challenge: the ability to blend two different types of quantum dots to control the electrical property of the resulting film. We report on the preparation of binary mixture films containing midwavelength infrared Ag₂Se intraband quantum dots and the fabrication of p-n heterojunction diodes with strong rectifying characteristics. The peak specific detectivity at 4.5 μm was measured to be 10⁷ Jones at room temperature, which is an orders of magnitude improvement compared to the previous generation of intraband quantum dot detectors.

Synthesis of IR-emitting HgTe quantum dots using an ionic liquid-based tellurium precursor

New scalable precursor chemistries for quantum dots are highly desirable and ionic liquids are viewed as an attractive alternative to existing solvents, as they are often considered green and recyclable. Here we report the synthesis of HgTe quantum dots with emission in the near-IR region using a phosphonium based ionic liquid, and without standard phosphine capping agents.

Correlating Structure and Detection Properties in HgTe Nanocrystal Films

HgTe nanocrystals (NCs) enable broadly tunable infrared absorption, now commonly used to design light sensors. This material tends to grow under multipodic shapes and does not present well-defined size distributions. Such point generates traps and reduces the particle packing, leading to a reduced mobility. It is thus highly desirable to comprehensively explore the effect of the shape on their performance. Here, we show, using a combination of electron tomography and tight binding simulations, that the charge dissociation is strong within HgTe NCs, but poorly shape dependent. Then, we design a dual-gate field-effect-transistor made of tripod HgTe NCs and use it to generate a planar p-n junction, offering more tunability than its vertical geometry counterpart. Interestingly, the performance of the tripods is higher than sphere ones, and this can be correlated with a stronger Te excess in the case of sphere shapes which is responsible for a higher hole trap density.

Infrared photoconduction at the diffusion length limit in HgTe nanocrystal arrays

Narrow band gap nanocrystals offer an interesting platform for alternative design of low-cost infrared sensors. It has been demonstrated that transport in HgTe nanocrystal arrays occurs between strongly-coupled islands of nanocrystals in which charges are partly delocalized. This, combined with the scaling of the noise with the active volume of the film, make case for device size reduction. Here, with two steps of optical lithography we design a nanotrench which effective channel length corresponds to 5–10 nanocrystals, matching the carrier diffusion length. We demonstrate responsivity as high as 1 kA W⁻¹, which is 10⁵ times higher than for conventional µm-scale channel length. In this work the associated specific detectivity exceeds 10¹² Jones for 2.5 µm peak detection under 1 V at 200 K and 1 kHz, while the time response is as short as 20 µs, making this performance the highest reported for HgTe NC-based extended short-wave infrared detection.

Infrared nanocrystals have become an enabling building block for the design of low-cost infrared sensors. Here, Chu et al. design a nanotrench device geometry at the diffusion length limit in HgTe nanocrystals and demonstrate the record high sensing performance operated in the short-wave infrared.

Colloidal HgTe Quantum Dot/Graphene Phototransistor with a Spectral Sensitivity Beyond 3 µm

Infrared light detection enables diverse technologies ranging from night vision to gas analysis. Emerging technologies such as low-cost cameras for self-driving cars require highly sensitive, low-cost photodetector cameras with spectral sensitivities up to wavelengths of 10 µm. For this purpose, colloidal quantum dot (QD) graphene phototransistors offer a viable alternative to traditional technologies owing to inexpensive synthesis and processing of QDs. However, the spectral range of QD/graphene phototransistors is thus far limited to 1.6 µm. Here, HgTe QD/graphene phototransistors with spectral sensitivity up to 3 µm are presented, with specific detectivities of 6 × 108 Jones at a wavelength of 2.5 µm and a temperature of 80 K. Even at kHz light modulation frequencies, specific detectivities exceed 108 Jones making them suitable for fast video imaging. The simple device architecture and QD film patterning in combination with a broad spectral sensitivity manifest an important step toward low-cost, multi-color infrared cameras.

Ternary alloyed HgCdTe nanocrystals for short-wave and mid-wave infrared region optoelectronic applications

Semiconductor quantum dots (QDs) are emerging as the forefront alternative for the conventional imaging technology, particularly in infrared region from near infrared (0.75–1.4 μm) to long-wave infrared (8–14 μm) region. A handful of materials are explored for mid infrared imaging QDs and they are all invariably binary semiconductor compounds. Ternary alloyed quantum dots in many previous cases have shown properties that are unique and better than parent binary compounds. In this work, we have synthesized ternary alloyed HgCdTe quantum dots and studied their photophysical properties. Previously studied ternary alloyed HgCdTe CQDs absorb and emit in regions limited upto near-infrared region. We have tuned the excitonic absorption of HgCdTe QDs in the range of 2.2–5 μm, where addition of cadmium clearly showed blueshift in excitonic peak as compared to that of HgTe QDs. Structural properties are studied by TEM, XRD & XPS techniques. Electrical behaviour is studied by measuring I-V, I-V-T curves. Photodetectors are fabricated in photoconductive geometry showing promising photo-response under visible (532 nm) and NIR (810 nm, 1550 nm) excitation. Responsivity of the devices is in the order of 1 mA W−1 at 1 V bias and show good linearity over irradiance range of 0.025 and 2.5 W cm−2. These results pave the way for development of next generation cost-effective short-wave and mid-wave infrared region optoelectronic devices based on narrow bandgap HgCdTe nanocrystals.

Shape-Controlled HgTe Colloidal Quantum Dots and Reduced Spin-Orbit Splitting in the Tetrahedral Shape

Spherical and tetrahedral HgTe colloidal quantum dots (CQDs) are synthesized, and their doping is tuned electrochemically. Compared to spherical dots of a similar volume, the tetrahedral CQDs show a decrease in confinement energy as well as a sharper band edge absorption. The intraband spectra of the tetrahedral CQDs also display a smaller splitting from spin-orbit coupling. The shape-controlled synthesis with an improved size distribution and sharper optical features could find applications in optoelectronic devices.

Advances of Sensitive Infrared Detectors with HgTe Colloidal Quantum Dots

The application of infrared detectors based on epitaxially grown semiconductors such as HgCdTe, InSb and InGaAs is limited by their high cost and difficulty in raising operating temperature. The development of infrared detectors depends on cheaper materials with high carrier mobility, tunable spectral response and compatibility with large-scale semiconductor processes. In recent years, the appearance of mercury telluride colloidal quantum dots (HgTe CQDs) provided a new choice for infrared detection and had attracted wide attention due to their excellent optical properties, solubility processability, mechanical flexibility and size-tunable absorption features. In this review, we summarized the recent progress of HgTe CQDs based infrared detectors, including synthesis, device physics, photodetection mechanism, multi-spectral imaging and focal plane array (FPA).

Transformation of Colloidal Quantum Dot: From Intraband Transition to Localized Surface Plasmon Resonance

An increase in the carrier density of semiconductor nanocrystals can gradually change the origin of the optical property from the excitonic transition to the localized surface plasmon resonances. Here, we present the evolution of the electronic transition of self-doped Ag₂Se colloidal quantum dots, from the intraband transition to the localized surface plasmon resonances along with a splitting of the intraband transition (1P_e-1S_e). The minimum fwhm of the split intraband transition is only 23.7 meV, which is exceptionally narrow compared to that of metal oxide nanocrystals showing LSPRs, inferring that the electron-electron scattering is significantly suppressed due to the smaller carrier density. The splitting of the intraband transition mainly results from the asymmetrical crystal structure of the tetragonal Ag₂Se CQDs and becomes distinct when the nanocrystal changes its crystal structure from the cubic to tetragonal structure. Maximizing the discrete energy levels in the quantum dot along with mixing with plasmonic characters may provide opportunities to fully harness merits of both the quantum confinement effect and localized surface plasmon resonance characters.

Quantum dot solids showing state-resolved band-like transport

Improving charge mobility in quantum dot (QD) films is important for the performance of photodetectors, solar cells and light-emitting diodes. However, these applications also require preservation of well defined QD electronic states and optical transitions. Here, we present HgTe QD films that show high mobility for charges transported through discrete QD states. A hybrid surface passivation process efficiently eliminates surface states, provides tunable air-stable n and p doping and enables hysteresis-free filling of QD states evidenced by strong conductance modulation. QD films dried at room temperature without any post-treatments exhibit mobility up to μ ~ 8 cm² V^-1 s^-1 at a low carrier density of less than one electron per QD, band-like behaviour down to 77 K, and similar drift and Hall mobilities at all temperatures. This unprecedented set of electronic properties raises important questions about the delocalization and hopping mechanisms for transport in QD solids, and introduces opportunities for improving QD technologies.

Auger Suppression in n-Type HgSe Colloidal Quantum Dots

Transient infrared photoluminescence upconversion is used to study the exciton dynamics in small-gap HgSe colloidal quantum dots in the 2000-6500 cm^-1 (0.25-0.80 eV) range. The intraband mid-infrared photoluminescence decays show absent or greatly reduced Auger relaxation of biexcitons, proposed as a generic feature of weakly n-type quantum dots due to the sparse density of states in the conduction band. The nonradiative relaxation of the intraband carriers is instead consistent with near-field energy transfer to molecular vibrations of the surface ligands. In contrast, the interband near-infrared photoluminescence decays exhibit the typical distinct exciton and biexciton lifetimes with Auger coefficients comparable to other similarly sized quantum dots. Also observed are spectral and dynamical evidence of fine structure in the intraband transitions consistent with spin-orbit splitting of the electron P levels, and the emergence of plasmonic resonances in large particles.

Colloidal quantum dots for thermal infrared sensing and imaging

Colloidal quantum dots provide a powerful materials platform to engineer optoelectronics devices, opening up new opportunities in the thermal infrared spectral regions where no other solution-processed material options exist. This mini-review collates recent research reports that push the technological envelope of colloidal quantum dot-based photodetectors toward mid- and long-wavelength infrared. We survey the synthesis and characterization of various thermal infrared colloidal quantum dots reported to date, discuss the basic theory of device operation, review the fabrication and measurement of photodetectors, and conclude with the future prospect of this emerging technology.

Conduction Band Fine Structure in Colloidal HgTe Quantum Dots

HgTe colloidal quantum dots (QDs) are of interest because quantum confinement of semimetallic bulk HgTe allows one to synthetically control the bandgap throughout the infrared. Here, we synthesize highly monodisperse HgTe QDs and tune their doping both chemically and electrochemically. The monodispersity of the QDs was evaluated using small-angle X-ray scattering (SAXS) and suggests a diameter distribution of ∼10% across multiple batches of different sizes. Electron-doped HgTe QDs display an intraband absorbance and bleaching of the first two excitonic features. We see splitting of the intraband peaks corresponding to electronic transitions from the occupied 1S_e state to a series of nondegenerate 1P_e states. Spectroelectrochemical studies reveal that the degree of splitting and relative intensity of the intraband features remain constant across doping levels up to two electrons per QD. Theoretical modeling suggests that the splitting of the 1P_e level arises from spin-orbit coupling and reduced QD symmetry. The fine structure of the intraband transitions is observed in the ensemble studies due to the size uniformity of the as-synthesized QDs and strong spin-orbit coupling inherent to HgTe.

Fast and Sensitive Colloidal Quantum Dot Mid-Wave Infrared Photodetectors

Colloidal quantum dots (CQDs) with a band gap tunable in the mid-wave infrared (MWIR) region provide a cheap alternative to epitaxial commercial photodetectors such as HgCdTe (MCT) and InSb. Photoconductive HgTe CQD devices have demonstrated the potential of CQDs for MWIR photodetection but face limitations in speed and sensitivity. Recently, a proof-of-concept HgTe photovoltaic (PV) detector was realized, achieving background-limited infrared photodetection at cryogenic temperatures. Using a modified PV device architecture, we report up to 2 orders of magnitude improvement in the sensitivity of the HgTe CQD photodetectors. A solid-state cation exchange method was introduced during device fabrication to chemically modify the interface potential, leading to an order of magnitude improvement of external quantum efficiency at room temperature. At 230 K, the HgTe CQD photodetectors reported here achieve a sensitivity of 10⁹ Jones with a cutoff wavelength between 4 and 5 μm, which is comparable to that of commercial photodetectors. In addition to the chemical treatment, a thin-film interference structure was devised using an optical spacer to achieve near unity internal quantum efficiency upon reducing the operating temperature. The enhanced sensitivity of the HgTe CQD photodetectors reported here should motivate interest in a cheap, solution-processed MWIR photodetector for applications extending beyond research and military defense.

Slow Auger Relaxation in HgTe Colloidal Quantum Dots

The biexciton lifetimes in HgTe colloidal quantum dots are measured as a function of particle size. Samples produced by two synthetic methods, leading to partially aggregated or well-dispersed particles, exhibit markedly different dynamics. The relaxation characteristics of partially aggregated HgTe inhibit reliable determinations of the Auger lifetime. In well-dispersed HgTe quantum dots, the biexciton lifetime increases approximately linearly with particle volume, confirming trends observed in other systems. The extracted Auger coefficient is three orders of magnitude smaller than that for bulk HgCdTe materials with similar energy gaps. We discuss these findings in the context of understanding Auger relaxation in quantum-confined systems and their relevance to mid-infrared optoelectronic devices based on HgTe colloidal quantum dots.

Band Edge Dynamics and Multiexciton Generation in Narrow Band Gap HgTe Nanocrystals

Mercury chalcogenide nanocrystals and especially HgTe appear as an interesting platform for the design of low cost mid-infrared (mid-IR) detectors. Nevertheless, their electronic structure and transport properties remain poorly understood, and some critical aspects such as the carrier relaxation dynamics at the band edge have been pushed under the rug. Some of the previous reports on dynamics are setup-limited, and all of them have been obtained using photon energy far above the band edge. These observations raise two main questions: (i) what are the carrier dynamics at the band edge and (ii) should we expect some additional effect (multiexciton generation (MEG)) as such narrow band gap materials are excited far above the band edge? To answer these questions, we developed a high-bandwidth setup that allows us to understand and compare the carrier dynamics resonantly pumped at the band edge in the mid-IR and far above the band edge. We demonstrate that fast (>50 MHz) photoresponse can be obtained even in the mid-IR and that MEG is occurring in HgTe nanocrystal arrays with a threshold around 3 times the band edge energy. Furthermore, the photoresponse can be effectively tuned in magnitude and sign using a phototransistor configuration.