Highly Conductive and Transparent Reduced Graphene Oxide Nanoscale Films via Thermal Conversion of Polymer-Encapsulated Graphene Oxide Sheets

Graphene-Based Transparent Flexible Strain Gauges with Tunable Sensitivity and Strain Range

Monolayers of graphene oxide, assembled into densely packed sheets at an immiscible hexane/water interface, form transparent conducting films on polydimethylsiloxane membranes after reduction in hydroiodic acid (HI) vapor to reduced graphene oxide (rGO). Prestraining and relaxing the membranes introduces cracks in the rGO film. Subsequent straining opens these cracks and induces piezoresistivity, enabling their application as transparent strain gauges. The sensitivity and strain range of these gauges is controlled by the cracked film structure that is determined by the reducing conditions used in manufacture. Reduction for 30 s in HI vapor leads to an array of parallel cracks that do not individually span the membrane. These cracks do not extend on subsequent straining, leading to a gauge with a usable strain range >0.2 and gauge factor (GF) at low strains ranging from 20 to 100, depending on the prestrain applied. The GF reduces with increasing applied strain and asymptotes to about 3, for all prestrains. Reduction for 60 s leads to cracks spanning the entire membrane and an increased film resistance but a highly sensitive strain gauge, with GF ranging from 800 to 16,000. However, the usable strain range reduces to <0.01. A simple equivalent resistor model is proposed to describe the behavior of both gauge types. The gauges show a repeatable and stable response with loading frequencies >1 kHz and have been used to detect human body strains in a simple e-skin demonstration.

Poly(3-hexylthiophene)-Based Organic Thin-Film Transistors with Virgin Graphene Oxide as an Interfacial Layer

We fabricated and characterized poly(3-hexylthiophene-2, 5-diyl) (P3HT)-based Organic thin-film transistors (OTFTs) containing an interfacial layer made from virgin Graphene Oxide (GO). Previously chemically modified GO and reduced GO (RGO) were used to modify OTFT interfaces. However, to our knowledge, there are no published reports where virgin GO was employed for this purpose. For the sake of comparison, OTFTs without modification were also manufactured. The structure of the devices was based on the Bottom Gate Bottom Contact (BGBC) OTFT. We show that the presence of the GO monolayer on the surface of the OTFT's SiO₂ dielectric and Au electrode surface noticeably improves their performance. Namely, the drain current and the field-effect mobility of OTFTs are considerably increased by modifying the interfaces with the virgin GO deposition. It is suggested that the observed enhancement is connected to a decrease in the contact resistance of GO-covered Au electrodes and the particular structure of the P3HT layer on the dielectric surface. Namely, we found a specific morphology of the organic semiconductor P3HT layer, where larger interconnecting polymer grains are formed on the surface of the GO-modified SiO₂. It is proposed that this specific morphology is formed due to the increased mobility of the P3HT segments near the solid boundary, which was confirmed via Differential Scanning Calorimetry measurements.

Investigation into morphological and electromechanical surface properties of reduced-graphene-oxide-loaded composite fibers for bone tissue engineering applications: A comprehensive nanoscale study using atomic force microscopy approach

We decided to implement an extensive atomic force microscopy study in order to get deeper understanding of surface-related nanoscale properties of 3D printed pristine polycaprolactone and its reduced-graphene-oxide-loaded composites. The study included surface visualization and roughness quantification, elastic modulus and adhesion force assessment with force spectroscopy, along with kelvin probe force microscopy evaluation of local changes of surface potential. Atomic force microscopy examination was followed by scanning electron microscopy visualization and wettability assessment. Moreover, systematic examination of reduced graphene oxide flakes fabricated exclusively for this study was performed, including: scanning electron microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and combustion elemental analysis. The addition of reduced graphene oxide resulted in thickening of the composite fibers and surface roughness enhancement. In addition, elastic modulus of composite fibers was higher and at the same time adhesion forces between scanning probe and tested surface was lower than for pristine polymeric ones. Lastly, we recorded local (nanoscale) alterations of surface potential of fibers with addition of graphene-derivative. The results clearly suggest graphene derivative's dose-dependent alteration of elastic modulus and adhesion force recorded with atomic force microscope. Moreover, changes of the material's surface properties were followed by changes of its electrical properties.

Functionalized Reduced Graphene Oxide Thin Films for Ultrahigh CO2 Gas Sensing Performance at Room Temperature

The demand for carbon dioxide (CO₂) gas detection is increasing nowadays. However, its fast detection at room temperature (RT) is a major challenge. Graphene is found to be the most promising sensing material for RT detection, owing to its high surface area and electrical conductivity. In this work, we report a highly edge functionalized chemically synthesized reduced graphene oxide (rGO) thin films to achieve fast sensing response for CO₂ gas at room temperature. The high amount of edge functional groups is prominent for the sorption of CO₂ molecules. Initially, rGO is synthesized by reduction of GO using ascorbic acid (AA) as a reducing agent. Three different concentrations of rGO are prepared using three AA concentrations (25, 50, and 100 mg) to optimize the material properties such as functional groups and conductivity. Thin films of three different AA reduced rGO suspensions (AArGO25, AArGO50, AArGO100) are developed and later analyzed using standard FTIR, XRD, Raman, XPS, TEM, SEM, and four-point probe measurement techniques. We find that the highest edge functionality is achieved by the AArGO25 sample with a conductivity of ~1389 S/cm. The functionalized AArGO25 gas sensor shows recordable high sensing properties (response and recovery time) with good repeatability for CO₂ at room temperature at 500 ppm and 50 ppm. Short response and recovery time of ~26 s and ~10 s, respectively, are achieved for 500 ppm CO₂ gas with the sensitivity of ~50 Hz/µg. We believe that a highly functionalized AArGO CO₂ gas sensor could be applicable for enhanced oil recovery, industrial and domestic safety applications.

Camphor-Based CVD Bilayer Graphene/Si Heterostructures for Self-Powered and Broadband Photodetection

This work demonstrates a self-powered and broadband photodetector using a heterojunction formed by camphor-based chemical vaper deposition (CVD) bilayer graphene on p-Si substrates. Here, graphene/p-Si heterostructures and graphene layers serve as ultra-shallow junctions for UV absorption and zero bandgap junction materials (<Si bandgap (1.1 eV)) for long-wave near-infrared (LWNIR) absorption, respectively. According to the Raman spectra and large-area (16 × 16 μm²) Raman mapping, a low-defect, >95% coverage bilayer and high-uniformity graphene were successfully obtained by camphor-based CVD processes. Furthermore, the carrier mobility of the camphor-based CVD bilayer graphene at room temperature is 1.8 × 10³ cm²/V·s. Due to the incorporation of camphor-based CVD graphene, the graphene/p-Si Schottky junctions show a good rectification property (rectification ratio of ~110 at ± 2 V) and good performance as a self-powered (under zero bias) photodetector from UV to LWNIR. The photocurrent to dark current ratio (PDCR) value is up to 230 at 0 V under white light illumination, and the detectivity (D*) is 8 × 10¹² cmHz^1/2/W at 560 nm. Furthermore, the photodetector (PD) response/decay time (i.e., rise/fall time) is ~118/120 μs. These results support the camphor-based CVD bilayer graphene/Si Schottky PDs for use in self-powered and ultra-broadband light detection in the future.

Adhesion and Stability of Nanocellulose Coatings on Flat Polymer Films and Textiles

Renewable nanocellulose materials received increased attention owing to their small dimensions, high specific surface area, high mechanical characteristics, biocompatibility, and compostability. Nanocellulose coatings are among many interesting applications of these materials to functionalize different by composition and structure surfaces, including plastics, polymer coatings, and textiles with broader applications from food packaging to smart textiles. Variations in porosity and thickness of nanocellulose coatings are used to adjust a load of functional molecules and particles into the coatings, their permeability, and filtration properties. Mechanical stability of nanocellulose coatings in a wet and dry state are critical characteristics for many applications. In this work, nanofibrillated and nanocrystalline cellulose coatings deposited on the surface of polymer films and textiles made of cellulose, polyester, and nylon are studied using atomic force microscopy, ellipsometry, and T-peel adhesion tests. Methods to improve coatings’ adhesion and stability using physical and chemical cross-linking with added polymers and polycarboxylic acids are analyzed in this study. The paper reports on the effect of the substrate structure and ability of nanocellulose particles to intercalate into the substrate on the coating adhesion.

Evolution of 3D Printing Methods and Materials for Electrochemical Energy Storage

Additive manufacturing has revolutionized the building of materials, and 3D-printing has become a useful tool for complex electrode assembly for batteries and supercapacitors. The field initially grew from extrusion-based methods and quickly evolved to photopolymerization printing, while supercapacitor technologies less sensitive to solvents more often involved material jetting processes. The need to develop higher-resolution multimaterial printers is borne out in the performance data of recent 3D printed electrochemical energy storage devices. Underpinning every part of a 3D-printable battery are the printing method and the feed material. These influence material purity, printing fidelity, accuracy, complexity, and the ability to form conductive, ceramic, or solvent-stable materials. The future of 3D-printable batteries and electrochemical energy storage devices is reliant on materials and printing methods that are co-operatively informed by device design. Herein, the material and method requirements in 3D-printable batteries and supercapacitors are addressed and requirements for the future of the field are outlined by linking existing performance limitations to requirements for printable energy-storage materials, casings, and direct printing of electrodes and electrolytes. A guide to materials and printing method choice best suited for alternative-form-factor energy-storage devices to be designed and integrated into the devices they power is thus provided.

Cadmium telluride quantum dots/graphene oxide/poly vinyl acetate (CdTe QDs/GO/PVAc) nanocomposite: a novel sensor for real time gamma radiation detection

The design of organic/inorganic nanoparticles hybrids provides the great potential for the fabrication of γ-ray sensor systems. Herein, structural and dosimetric properties of the gamma irradiated poly vinyl acetate (PVAc) doped with cadmium telluride quantum dots (CdTe QDs) and graphene oxide (GO) nanoflakes have been investigated. Thioglycolic acid (TGA) capped water-soluble CdTe QDs and (GO) nanoflakes are synthesized and characterized. Then, CdTe QDs/GO/PVAc sensors were formed by post-depositing CdTe and GO over polymer matrix. The photophysical interactions between nanoparticles and organic polymer have been investigated using ohmic contact detectors with two gold coated electrodes. Real time dose rate information of the sensors such as sensitivity, repeatability, and the linearity of dose rate response were assessed. A wider photoelectric response range and wider gamma harvesting range were observed in the resultant hybrid gamma sensor at a standard bias voltage with respect to non-hybrid CdTe QDs/PVAc sensors.

One-Step Synthesis of Silver Nanowires with Ultra-Long Length and Thin Diameter to Make Flexible Transparent Conductive Films

High aspect ratio silver nanowires (AgNWs) with ultra-long length and thin diameter were synthesized through bromine ion (Br⁻)-assisted one-step synthesis method. The bromine ions were used as pivotal passivating agent. When the molar ratio of Br⁻/Cl⁻ was 1:4, the average diameter of AgNWs was as low as ~40 nm, the average length was as high as ~120 μm, and the aspect ratio reached 2500. Networks of AgNWs were fabricated using as-prepared high-quality AgNWs as conducting material and hydroxyethyl cellulose (HEC) as the adhesive polymer. As a result, a low sheet resistance down to ~3.5 Ω sq⁻¹ was achieved with a concomitant transmittance of 88.20% and a haze of 4.12%. The ultra-low sheet resistance of conductive film was attributed to the long and thin AgNWs being able to form a more effective network. The adhesion of the AgNWs to the substrate was 0/5B (ISO/ASTM). The insights given in this paper provide the key guidelines for bromine ion-assisted synthesis of long and thin AgNWs, and further designing low-resistance AgNW-based conductive film for optoelectronic devices.

Transparent Conductive Electrodes Based on Graphene-Related Materials

Transparent conducting electrodes (TCEs) are the most important key component in photovoltaic and display technology. In particular, graphene has been considered as a viable substitute for indium tin oxide (ITO) due to its optical transparency, excellent electrical conductivity, and chemical stability. The outstanding mechanical strength of graphene also provides an opportunity to apply it as a flexible electrode in wearable electronic devices. At the early stage of the development, TCE films that were produced only with graphene or graphene oxide (GO) were mainly reported. However, since then, the hybrid structure of graphene or GO mixed with other TCE materials has been investigated to further improve TCE performance by complementing the shortcomings of each material. This review provides a summary of the fabrication technology and the performance of various TCE films prepared with graphene-related materials, including graphene that is grown by chemical vapor deposition (CVD) and GO or reduced GO (rGO) dispersed solution and their composite with other TCE materials, such as carbon nanotubes, metal nanowires, and other conductive organic/inorganic material. Finally, several representative applications of the graphene-based TCE films are introduced, including solar cells, organic light-emitting diodes (OLEDs), and electrochromic devices.

Effects of Graphene Nanoplatelet Size and Surface Area on the AC Electrical Conductivity and Dielectric Constant of Epoxy Nanocomposites

Epoxy nanocomposites reinforced with various grades of multilayer graphene nanoplatelets (GNPs) are manufactured and tested. The effects of size, surface area, and concentration of GNP, as well as alternating current (AC) frequency on the electrical and dielectric properties of epoxy nanocomposites are experimentally investigated. GNPs with larger size and surface area are always beneficial to increase the electrical conductivity of the composites. However, their effects on the dielectric constant are highly dependent on GNP concentration and AC frequency. At lower GNP concentration, the dielectric constant increases proportionally with the increase in GNP size, while decreasing as the AC frequency increases. At higher GNP concentration in epoxy, the dielectric constant first increases with the increase of the GNP size, but decreases thereafter. This trend is also observed for varying the processed GNP surface area on the dielectric constant. Moreover, the variations of the electrical conductivity and dielectric constant with the GNP concentration and AC frequency are then correlated with the measured interfiller spacing and GNP diameter.

En Route to Practicality of the Polymer Grafting Technology: One-Step Interfacial Modification with Amphiphilic Molecular Brushes

Surface modification with polymer grafting is a versatile tool for tuning the surface properties of a wide variety of materials. From a practical point of view, such a process should be readily scalable and transferable between different substrates and consist of as least number of steps as possible. To this end, a cross-linkable amphiphilic copolymer system that is able to bind covalently to surfaces and form permanently attached networks via a one-step procedure is reported here. This system consists of brushlike copolymers (molecular brushes) made of glycidyl methacrylate, poly(oligo(ethylene glycol) methyl ether methacrylate), and lauryl methacrylate, which provide the final product with tunable reactivity and balance between hydrophilicity and hydrophobicity. The detailed study of the copolymer synthesis and properties has been carried out to establish the most efficient pathway to design and tailor this amphiphilic molecular brush system for specific applications. As an example of the applications, we showed the ability to control the deposition of graphene oxide (GO) sheets on both hydrophilic and hydrophobic surfaces using GO modified with the molecular brushes. Also, the capability to tune the osteoblast cell adhesion with the copolymer-based coatings was demonstrated.