Interaction of gold(I) and gold(III) complexes with algal biomass

Microalgal flocculation and sedimentation: spatiotemporal evaluation of the effects of the pH and calcium concentration

The high cost of harvesting microalgae is a major hurdle for the microalgae industry, and an efficient pre-concentration method is required. In this study, the effects of using different pH values (between pH 3 and 11) and calcium (Ca²⁺) concentrations (between 0 and 5 mM) on Chlorella vulgaris sedimentation were investigated by evaluating the spacio-temporal distributions of microalgae cells. Fast and efficient sedimentation occurred (within 10 min) at a high Ca²⁺ concentration (5 mM) at pH 9 and 11. However, the sediment volume was lower at a Ca²⁺ concentration of 3 mM than at a Ca²⁺ concentration of 5 mM. This indicated that the Ca²⁺ concentration strongly affected the sediment volume. Fast sedimentation and a low sediment volume were found at pH 7 and a Ca²⁺ concentration of 5 mM, probably because of the neutral charge in the system (adhesion to calcium precipitates would have occurred at a high pH). The highest Ca²⁺ recovery (82%) was achieved when sediment produced at pH 11 and a Ca²⁺ concentration of 5 mM was acidified to pH 3.

Cell population behavior of the unicellular red alga Galdieria sulphuraria during precious metal biosorption

This study investigates the biosorption mechanism, including cell population behavior, of trace amounts of precious metals (gold, palladium, and platinum) in a unicellular red alga, Galdieria sulphuraria. Single-cell inductively coupled plasma mass spectrometry showed that the number of adsorbing cells and the concentration of adsorbed metal per cell varied depending on solution acidity and metal species. The X-ray absorption fine structure in 5 mM HCl solution indicated that the adsorbed Au formed inner-sphere complexes with S, whereas the adsorbed Pd and Pt formed an inner-sphere complexes with N and/or S. In 500 mM HCl solution, the adsorbed Au and Pd formed inner-sphere complexes only with S, and the Au formed a structure similar to Au₂S. At higher acidity, Au and Pd were recovered by interacting with residues that formed more stable complexes, which was accompanied by changes in the behavior of cell populations adsorbing the metals. This is the first study to demonstrate the relationship between changes in the behavior of cell populations and chemical interactions that occur between substrate elements and biomaterial residues during biosorption. The findings of this study provide deeper insights into the biosorption mechanism and a background for the design of an environmentally friendly biosorbent.

Recent advances in waste-derived functional materials for wastewater remediation

Water pollution is a major concern for public health and a sustainable future. It is urgent to purify wastewater with effective methods to ensure a clean water supply. Most wastewater remediation techniques rely heavily on functional materials, and cost-effective materials are thus highly favorable. Of great environmental and economic significance, developing waste-derived materials for wastewater remediation has undergone explosive growth recently. Herein, the applications of waste (e.g., biowastes, electronic wastes, and industrial wastes)-derived materials for wastewater purification are comprehensively reviewed. Sophisticated strategies for turning wastes into functional materials are firstly summarized, including pyrolysis and combustion, hydrothermal synthesis, sol-gel method, co-precipitation, and ball milling. Moreover, critical experimental parameters within different design strategies are discussed. Afterward, recent applications of waste-derived functional materials in adsorption, photocatalytic degradation, electrochemical treatment, and advanced oxidation processes (AOPs) are analyzed. We mainly focus on the development of efficient functional materials via regulating the internal and external characteristics of waste-derived materials, and the material's property-performance correlation is also emphasized. Finally, the key future perspectives in the field of waste-derived materials-driven water remediation are highlighted.

Recovery of Au from dilute aqua regia solutions via adsorption on the lyophilized cells of a unicellular red alga Galdieria sulphuraria: A mechanism study

The high electrical conductivity, chemical stability, and low toxicity of elemental Au make it a highly valuable resource. However, wastewater produced during the mining, utilization, and disposal of Au inevitably contains small amounts (10-40 mg L^-1) of Au, thus posing environmental risks. It is too acidic to be treated with inexpensive and eco-friendly bioadsorbents previously studied for the remediation of less acidic effluents. Herein, lyophilized Galdieria sulphuraria cells are shown to directly adsorb Au from simulated Au-containing wastewater with a total acid concentration of 4 M, achieving an adsorption capacity of 35 ± 2.5 mg g^-1 Au after 30-min exposure and a selectivity that exceeds that of an ion-exchange resin and is comparable to that of activated carbon. Additionally, Au adsorbed on these cells is more easily eluted than that adsorbed on the ion-exchange resin or activated carbon. Detailed characterizations reveal that Au accumulates on the surface of lyophilized cells, where it is mainly present as AuCl₄^- and not as Au⁰, in contrast to a previously proposed adsorption mechanism. Thus, our work provides valuable insights into the mechanism of Au adsorption on biomaterials and paves the way to the cheap and eco-friendly recovery of Au from acidic wastewater.

Microbial cell factories a new dimension in bio-nanotechnology: exploring the robustness of nature

Bio-based nanotechnology has its existence in biological dimensions e.g. microbial cell factories (bacteria, fungi. algae, yeast, cyanobacteria) plants, and biopolymers. They provide multipurpose biological platforms to supply well-designed materials for diverse nano-biotechnological applications. The "green or bio-based synthesis of nanoparticles (NPs)" has witnessed a research outburst in the past decade. The bio-based synthesis of NPs using microbial cell factories is a benign process and requires mild conditions for the synthesis with end products being less/non-toxic. As a result, its application has extended in multitudinous industries including environment, cosmetics, and pharmaceutical. Thus, the present review summarizes all the significant aspects of nanotechnology and the reason to switch towards the bio-based synthesis of NPs using microbial cell factories. It consists of a detailed description of the bio-based methods employed for the synthesis and classification of NPs. Also, a comprehensive study on the application of bio-based NPs in the various industrial and biotechnological domains has been discussed. The limitation and its solution would help identify the applicability of NPs to "identified and unidentified" sectors.

Polymer inclusion membrane applications for transport of metal ions: A critical review

The co-existence of heavy metals in industrial effluents is a prevalent problem. Heavy metals are not biodegradable and can remain in the environment when left untreated. Therefore, metals must be removed from wastewater to protect people's health and the environment. Also, these pollutants usually have dissimilar compositions and properties. Generally, metal treatment is performed using traditional methods, but new processes have been developed due to the disadvantages of traditional methods. Especially in the last 20 years, studies on polymer inclusion membranes have been carried out and the transport performance of metal ions has been investigated. It is a more convenient process than both ion exchange and liquid-liquid extraction methods due to the potential and performance of polymer inclusion membranes. When the studies in the literature are examined, it is seen that the performance of polymer inclusion membranes is higher than expected and also when the production conditions are examined, polymer inclusion membrane is more advantageous than other processes. This review is a summary of the studies on the removal and transport of metal by using polymer inclusion membranes in the literature over the last 20 years.

A Single-Molecule Observation of Dichloroaurate(I) Binding to an Engineered Mycobacterium smegmatis porin A (MspA) Nanopore

Gold(I) compounds are known to bind sulfur-containing proteins, forming the basis in the design of gold(I)-based drugs. However, the intrinsic molecular mechanism of the chemical reaction is easily hidden when monitored in ensemble. We have previously demonstrated that Mycobacterium smegmatis porin A (MspA) can be engineered (MspA-M) to contain a specialized nanoreactor to probe chemical reactions involving tetrachloroaurate(III). Here, we provide further investigations of coordination interactions between dichloroaurate(I) and MspA-M. Gold compounds of different coordination geometry and valence states are as well probed and evaluated, demonstrating the generality of MspA-M. With single-molecule evidence, MspA-M demonstrates a preference for dichloroaurate(I) than tetrachloroaurate(III), an observation in a single molecule that has never been reported. By counting the maximum number of simultaneous ion bindings, the narrowly confined pore restriction also efficiently distinguishes dichloroaurate(I) and tetrachloroaurate(III) according to their differences in geometry or size. The above demonstration complemented a previous study by demonstrating other possible gold-based single-molecule chemical reactions observable by MspA. These observations bring insights in the understanding of gold-based coordination chemistry in a nanoscale.

Phycoremediation of Precious Metals by Cladophora fracta From Mine Gallery Waters Causing Environmental Contamination

We have presented a study to determine the possibility for the usage of Cladophora fracta as bioaccumulator of the metals (Au) and silver (Ag) both have characteristics of pollutant and precious in mine water. The highest concentrations accumulated by C. fracta were determined as 5.8 ± 0.3 and 5323 ± 75 µg/kg for Au and Ag, respectively. The results showed that the accumulation of the metals measured followed the order of Ag > Au. The Metal Pollution Index (MPI) values calculated between 39.37 × 10^-3 and 175.7 × 10^-3 were used to determine the pollution degree of C. fracta. As a result, it was determined that C. fracta highly accumulated the precious metals from the gallery water. Therefore, C. fracta was a good bioaccumulator for the remediation of Au and Ag in mine gallery waters. In this way, it is possible to minimize or eliminate the environmental risks of the precious metals in the gallery waters.

Live and lyophilized fungi-algae pellets as novel biosorbents for gold recovery: Critical parameters, isotherm, kinetics and regeneration studies

This study aimed to evaluate the potential of live and lyophilized fungi-algae pellets as biosorbents for gold recovery and their regeneration ability. The optimum conditions determined by Taguchi method were 1 g/L co-pellets, 9-10 mm size at 250 rpm of agitation speed and pH 3.5 and 2.0 for live and lyophilized co-pellets, respectively. The porous characteristics of fungi-algae pellets played an important role on gold adsorption. Lyophilized co-pellets achieved adsorption capacity of 112.36 mg/g which were comparable with some synthesized granular adsorbents and performed better than the live co-pellets due to more cell-wall polysaccharides involved in gold interaction. 97.77% of gold was selectively absorbed by the lyophilized co-pellets from multi-metal wastewater in column reactor. This study may provide new insights into the application of fungi-algae pelletized reactor in bioremediation of contaminated wastewater by precious metals and their recovery and the in-situ regeneration of biosorbents.

Impedimetric determination of Cs(I) using AuNPs@PoPD-DB24C8: A targeted molecular-scale perturbation

Most attributes of the bulk materials, especially in the solid-state, are directly dictated by a manner by which the molecules are ordered. Thus, it is expected that the possibility of controlling these structural orders would allow predominating some particular physical properties. The methodology used in this work follows the molecular scale perturbation occurred by Cs⁺ ion within a ternary composite of dibenzo-24-crown-8 (DB24C8), poly ortho-phenylenediamine (PoPD) and gold nanoparticles (AuNPs). Hypothetically, two former substances were respectively employed as recognition element and conductive platform to establish a monolithic structure that resembles supramolecular synthon in solid-state. The third precursor was Au(III) that carries out a dual role including vulcanization of the polymeric units via creating quinoid rings and solid signal amplification by deposition of AuNPs at the welded points. This strategy affords an intertwined ternary composite in which the electronical properties of the system can be directly affected by lowest agitation sensed by the recognition element, DB24C8, making the supported transducer capable of monitoring trace amount of Cs⁺ ion by Faradaic impedance spectroscopy (FIS) and single-frequency measurements (SFM). The fabricated sensor showed a signal change against Cs⁺ ion over the linear range of 0.6-25.0 nM with a detection limit of 0.37 nM (S/N = 3). Density functional theory (DFT) studies were used to explore the possible recognition mechanism, by which the incorporation of Cs⁺ ion meaningfully dispersed the structural order of the ternary system.

Interaction between the photosynthetic anoxygenic microorganism Rhodobacter sphaeroides and soluble gold compounds. From toxicity to gold nanoparticle synthesis

Biological processes using microorganisms for nanoparticle synthesis are appealing as eco-friendly nanofactories. The response of the photosynthetic bacterium Rhodobacter sphaeroides to gold exposure and its reducing capability of Au(III) to produce stable gold nanoparticles (AuNPs), using metabolically active bacteria and quiescent biomass, is reported in this study. In the former case, bacterial cells were grown in presence of gold chloride at physiological pH. Gold exposure was found to cause a significant increase of the lag-phase duration at concentrations higher than 10 μM, suggesting the involvement of a resistance mechanism activated by Au(III). Transmission Electron Microscopy (TEM) and Scanning Electron Microscopy/Energy Dispersive X-ray Spectrometry (SEM/EDS) analysis of bacterial cells confirmed the extracellular formation of AuNPs. Further studies were carried out on metabolically quiescent biomass incubated with gold chloride solution. The biosynthesized AuNPs were spherical in shape with an average size of 10 ± 3 nm, as analysed by Transmission Electron Microscopy (TEM). The nanoparticles were hydrophilic and stable against aggregation for several months. In order to identify the functional groups responsible for the reduction and stabilization of nanoparticles, AuNPs were analysed by Attenuated Total Reflectance-Fourier Transform Infrared (ATR-FTIR) spectroscopy, X-ray Photoelectron Spectroscopy (XPS), X-ray Fluorescence Spectrometry (XRF) and X-ray Absorption Spectroscopy (XAS) measurements. The obtained results indicate that gold ions bind to functional groups of cell membrane and are subsequently reduced by reducing sugars to gold nanoparticles and capped by a protein/peptide coat. Gold nanoparticles demonstrated to be efficient homogeneous catalysts in the degradation of nitroaromatic compounds.

Localization and Speciation of Chromium in Coptis chinensis Franch. using Synchrotron Radiation X-ray Technology and Laser Ablation ICP-MS

Coptis chinensis Franch. is one of the most important medicinal plants globally. However, this species contains relatively high concentrations of chromium (Cr) which potentially detrimental to human health. It is important to understand Cr localization and speciation in order to evaluate its accumulation and transportation mechanisms and minimize Cr transfer to humans. As little previous work in this area has been carried out, we utilized synchrotron radiation microscopic X-ray fluorescence (SR-μXRF) and laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) to spatially locate Cr, X-ray absorption near-edge spectroscopy (XANES) to analyze Cr speciation, and inductively coupled plasma mass spectrometry (ICP-MS) to detect Cr subcellular concentration. Micromapping results showed that Cr was distributed predominantly within the vascular cylinder, the periderm and some outer cortex, and the cortex and some vascular bundles in root, rhizome, and petiole, respectively. XANES data showed that Cr(VI) can be reduced to Cr(III) when grown with Cr(VI), and yielded a novel conclusion that this plant contain elemental chromium. ICP-MS data showed that Cr was primarily compartmentalized in cell walls in all tissues. The new insights on Cr accumulation in C. chinensis Franch. provide a theoretical basis for the evaluation of Cr in other medicinal plants.

Status of electronic waste recycling techniques: a review

The increasing use of electrical and electronic equipment leads to a huge generation of electronic waste (e-waste). It is the fastest growing waste stream in the world. Almost all electrical and electronic equipment contain printed circuit boards as an essential part. Improper handling of these electronic wastes could bring serious risk to human health and the environment. On the other hand, proper handling of this waste requires a sound management strategy for awareness, collection, recycling, and reuse. Nowadays, the effective recycling of this type of waste has been considered as a main challenge for any society. Printed circuit boards (PCBs), which are the base of many electronic industries, are rich in valuable heavy metals and toxic halogenated organic substances. In this review, the composition of different PCBs and their harmful effects are discussed. Various techniques in common use for recycling the most important metals from the metallic fractions of e-waste are illustrated. The recovery of metals from e-waste material after physical separation through pyrometallurgical, hydrometallurgical, or biohydrometallurgical routes is also discussed, along with alternative uses of non-metallic fraction. The data are explained and compared with the current e-waste management efforts done in Egypt. Future perspectives and challenges facing Egypt for proper e-waste recycling are also discussed.

Structural basis for expanding the application of bioligand in metal bioremediation: A review

Bioligands (BL) present in plant and microbes are primarily responsible for their use in metal decontamination. Both primary (proteins and amino acid) and secondary (proliferated) response in the form of BL is possible in plants and microbes toward metal bioremediation. Structure of these BL have specific requirement for preferential binding towards a particular metal in biomass. The aim of this review is to explore various templates from BL (as metal host) for the metal detoxification/decontamination and associated bioremediation. Mechanistic explanation for bioremediation may involve the various processes like: (i) electron transfer; (ii) translocation; and (iii) coordination number variation. HSAB (hard and soft acid and base) concept can act as guiding principle for many such processes. It is possible to investigate various structural homolog of BL (similar to secondary response in living stage) for the possible improvement in bioremediation process.

Recovery of gold from electronic waste using chemical assisted microbial biosorption (hybrid) technique

The aim of present study was to develop a modified method of gold recovery from e-waste. Selective biosorption of gold from contact point of printed circuit board was achieved by using the combination of ammonium thiosulfate (AT) and Lactobacillus acidophilus (LA).Improvement in biosorption was due to the π-π interaction and resultant change in amide absorption bond between AT and LA, as evidenced by infrared spectroscopy. Selection was justified by some basic postulates of ionic radii and confirmed by inductively coupled plasma atomic emission spectroscopy. This methodology provides a unique leaching-sorption method for gold recovery and 85% of gold was recovered (from AT leachant) by the proposed combination.

Effective and selective recovery of gold and palladium ions from metal wastewater using a sulfothermophilic red alga, Galdieria sulphuraria

The demand for precious metals has increased in recent years. However, low concentrations of precious metals dissolved in wastewater are yet to be recovered because of high operation costs and technical problems. The unicellular red alga, Galdieria sulphuraria, efficiently absorbs precious metals through biosorption. In this study, over 90% of gold and palladium could be selectively recovered from aqua regia-based metal wastewater by using G. sulphuraria. These metals were eluted from the cells into ammonium solutions containing 0.2M ammonium salts without other contaminating metals. The use of G. sulphuraria is an eco-friendly and cost-effective way of recovering low concentrations of gold and palladium discarded in metal wastewater.

Chemical and structural characterization of copper adsorbed on mosses (Bryophyta)

The adsorption of copper on passive biomonitors (devitalized mosses Hypnum sp., Sphagnum denticulatum, Pseudoscleropodium purum and Brachythecium rutabulum) was studied under different experimental conditions such as a function of pH and Cu concentration in solution. Cu assimilation by living Physcomitrella patents was also investigated. Molecular structure of surface adsorbed and incorporated Cu was studied by X-ray Absorption Spectroscopy (XAS). Devitalized mosses exhibited the universal adsorption pattern of Cu as a function of pH, with a total binding sites number 0.05-0.06 mmolg(dry)(-1) and a maximal adsorption capacity of 0.93-1.25 mmolg(dry)(-1) for these devitalized species. The Extended X-ray Absorption Fine Structure (EXAFS) fit of the first neighbor demonstrated that for all studied mosses there are ∼4.5 O/N atoms around Cu at ∼1.95 Å likely in a pseudo-square geometry. The X-ray Absorption Near Edge Structure (XANES) analysis demonstrated that Cu(II)-cellulose (representing carboxylate groups) and Cu(II)-phosphate are the main moss surface binding moieties, and the percentage of these sites varies as a function of solution pH. P. patens exposed during one month to Cu(2+) yielded ∼20% of Cu(I) in the form of Cu-S(CN) complexes, suggesting metabolically-controlled reduction of adsorbed and assimilated Cu(2+).

Biorecovery of gold as nanoparticles and its catalytic activities for p-nitrophenol degradation

Recovery of gold from aqueous solution using simple and economical methodologies is highly desirable. In this work, recovery of gold as gold nanoparticles (AuNPs) by Shewanella haliotis with sodium lactate as electron donor was explored. The results showed that the process was affected by the concentration of biomass, sodium lactate, and initial gold ions as well as pH value. Specifically, the presence of sodium lactate determines the formation of nanoparticles, biomass, and AuCl4 (-) concentration mainly affected the size and dispersity of the products, reaction pH greatly affected the recovery efficiency, and morphology of the products in the recovery process. Under appropriate conditions (5.25 g/L biomass, 40 mM sodium lactate, 0.5 mM AuCl4 (-), and pH of 5), the recovery efficiency was almost 99 %, and the recovered AuNPs were mainly spherical with size range of 10-30 nm (~85 %). Meanwhile, Fourier transforms infrared spectroscopy and X-ray photoelectron spectroscopy demonstrated that carboxyl and amine groups might play an important role in the process. In addition, the catalytic activity of the AuNPs recovered under various conditions was testified by analyzing the reduction rate of p-nitrophenol by borohydride. The biorecovered AuNPs exhibited interesting size and shape-dependent catalytic activity, of which the spherical particle with smaller size showed the highest catalytic reduction activity with rate constant of 0.665 min(-1).

Recovery of gold(0) nanoparticles from aqueous solutions using effluents from a bioremediation process

Biological processes for the recovery of gold from low-concentration media derived from leaching of secondary sources are of great importance due to the scarcity of the primary resources and the economic and environmental advantages of these methods.

Microalgae - A promising tool for heavy metal remediation

Biotechnology of microalgae has gained popularity due to the growing need for novel environmental technologies and the development of innovative mass-production. Inexpensive growth requirements (solar light and CO2), and, the advantage of being utilized simultaneously for multiple technologies (e.g. carbon mitigation, biofuel production, and bioremediation) make microalgae suitable candidates for several ecofriendly technologies. Microalgae have developed an extensive spectrum of mechanisms (extracellular and intracellular) to cope with heavy metal toxicity. Their wide-spread occurrence along with their ability to grow and concentrate heavy metals, ascertains their suitability in practical applications of waste-water bioremediation. Heavy metal uptake by microalgae is affirmed to be superior to the prevalent physicochemical processes employed in the removal of toxic heavy metals. In order to evaluate their potential and to fill in the loopholes, it is essential to carry out a critical assessment of the existing microalgal technologies, and realize the need for development of commercially viable technologies involving strategic multidisciplinary approaches. This review summarizes several areas of heavy metal remediation from a microalgal perspective and provides an overview of various practical avenues of this technology. It particularly details heavy metals and microalgae which have been extensively studied, and provides a schematic representation of the mechanisms of heavy metal remediation in microalgae.

Phytosynthesis of nanoparticles: concept, controversy and application

Nanotechnology is an exciting and powerful discipline of science; the altered properties of which have offered many new and profitable products and applications. Agriculture, food and medicine sector industries have been investing more in nanotechnology research. Plants or their extracts provide a biological synthesis route of several metallic nanoparticles which is more eco-friendly and allows a controlled synthesis with well-defined size and shape. The rapid drug delivery in the presence of a carrier is a recent development to treat patients with nanoparticles of certain metals. The engineered nanoparticles are more useful in increasing the crop production, although this issue is still in infancy. This is simply due to the unprecedented and unforeseen health hazard and environmental concern. The well-known metal ions such as zinc, iron and copper are essential constituents of several enzymes found in the human system even though the indiscriminate use of similar other metal nanoparticle in food and medicine without clinical trial is not advisable. This review is intended to describe the novel phytosynthesis of metal and metal oxide nanoparticles with regard to their shape, size, structure and diverse application in almost all fields of medicine, agriculture and technology. We have also emphasized the concept and controversial mechanism of green synthesis of nanoparticles.

Transport of gold nanoparticles through plasmodesmata and precipitation of gold ions in woody poplar

Poplar plants (Populus deltoides × nigra, DN-34) were used as a model to explore vegetative uptake of commercially available gold nanoparticles (AuNPs) and their subsequent translocation and transport into plant cells. AuNPs were directly taken up and translocated from hydroponic solution to poplar roots, stems and leaves. Total gold concentrations in leaves of plants treated with 15, 25 and 50 nm AuNPs at exposure concentrations of 498±50.5, 247±94.5 and 263±157 ng/mL in solutions were: 0.023±0.006, 0.0218±0.004 and 0.005±0.0003 µg/g dry weight, respectively, which accounted for 0.05, 0.10 and 0.03%, respectively, of the total gold mass added. The presence of total gold in plant tissues was measured by inductively coupled plasma mass spectrometry, while AuNPs were observed by transmission electron microscopy in plant tissues. In solution, AuNPs were distinguished from Au(III) ions by membrane separation and centrifugation. AuNPs behaved conservatively inside the plants and were not dissolved into gold ions. On the other hand, Au(III) ions were taken up and reduced into AuNPs inside whole plants. AuNPs were observed in the cytoplasm and various organelles of root and leaf cells. A distinct change in color from yellow to pink was observed as Au(III) ions were reduced and precipitated in hydroponic solution. The accumulation of AuNPs in the plasmodesma of the phloem complex in root cells clearly suggests ease of transport between cells and translocation throughout the whole plant, inferring the potential for entry and transfer in food webs.

Phage based green chemistry for gold ion reduction and gold retrieval

The gold mining industry has taken its toll on the environment, triggering the development of more environmentally benign processes to alleviate the waste load release. Here, we demonstrate the use of bacteriophages (phages) for biosorption and bioreduction of gold ions from aqueous solution, which potentially can be applied to remediate gold ions from gold mining waste effluent. Phage has shown a remarkably efficient sorption of gold ions with a maximum gold adsorption capacity of 571 mg gold/g dry weight phage. The product of this phage mediated process is gold nanocrystals with the size of 30-630 nm. Biosorption and bioreduction processes are mediated by the ionic and covalent interaction between gold ions and the reducing groups on the phage protein coat. The strategy offers a simple, ecofriendly and feasible option to recover of gold ions to form readily recoverable products of gold nanoparticles within 24 h.

Stoichiometrically controlled production of bimetallic Gold-Silver alloy colloids using micro-alga cultures

This paper reports the production of well-defined, highly stable Ag-Au alloy nanoparticles (NPs) using living cells of Chlamydomonas reinhardtii, with the composition of the bimetallic alloys being solely determined by the stoichiometric ratio in which the metal salts were added to the cultures. The NPs exhibited a single, well-defined surface plasmon resonance (SPR) band confirming that they were made of a homogeneous population of bimetallic alloys. Particle creation by the cells occurred in three stages: (1) internalization of the noble metals by the cells and their reduction resulting in the formation of the NPs; (2) entrapment of the NPs in the extracellular matrix (ECM) surrounding the cells, where they are colloidally stabilized; and (3) release of the NPs from the ECM to the culture medium. We also investigated the effect of the addition of the metals salts on cell viability and the impact on characteristics of the NPs formed. When silver was added to the cultures, cell viability was decreased and this resulted in a ~30nm red shift on the SPR band due to changes in the surrounding environment into which the NPs were released. The same observations (in SPR and cell viability) was made when gold was added to a final concentration of 2 × 10(-4)M, but not when the concentration was equal to 10(-4)M, where cell viability was high and the red shift was negligible.

Bioremediation of industrial effluents containing heavy metals using brewing cells of Saccharomyces cerevisiae as a green technology: a review

The release of heavy metals into the environment, mainly as a consequence of anthropogenic activities, constitutes a worldwide environmental pollution problem. Unlike organic pollutants, heavy metals are not degraded and remain indefinitely in the ecosystem, which poses a different kind of challenge for remediation. It seems that the "best treatment technologies" available may not be completely effective for metal removal or can be expensive; therefore, new methodologies have been proposed for the detoxification of metal-bearing wastewaters. The present work reviews and discusses the advantages of using brewing yeast cells of Saccharomyces cerevisiae in the detoxification of effluents containing heavy metals. The current knowledge of the mechanisms of metal removal by yeast biomass is presented. The use of live or dead biomass and the influence of biomass inactivation on the metal accumulation characteristics are outlined. The role of chemical speciation for predicting and optimising the efficiency of metal removal is highlighted. The problem of biomass separation, after treatment of the effluents, and the use of flocculent characteristics, as an alternative process of cell-liquid separation, are also discussed. The use of yeast cells in the treatment of real effluents to bridge the gap between fundamental and applied studies is presented and updated. The convenient management of the contaminated biomass and the advantages of the selective recovery of heavy metals in the development of a closed cycle without residues (green technology) are critically reviewed.

A further insight into the biosorption mechanism of Au(III) by infrared spectrometry

Background

The interactions of microbes with metal ions form an important basis for our study of biotechnological applications. Despite the recent progress in studying some properties of Au(III) adsorption and reduction by Bacillus megatherium D01 biomass, there is still a need for additional data on the molecular mechanisms of biosorbents responsible for their interactions with Au(III) to have a further insight and to make a better exposition.

Results

The biosorption mechanism of Au(III) onto the resting cell of Bacillus megatherium D01 biomass on a molecular level has been further studied here. The infrared (IR) spectroscopy on D01 biomass and that binding Au(III) demonstrates that the molecular recognition of and binding to Au(III) appear to occur mostly with oxygenous- and nitrogenous-active groups of polysaccharides and proteins in cell wall biopolymers, such as hydroxyl of saccharides, carboxylate anion of amino-acid residues (side-chains of polypeptide backbone), peptide bond (amide I and amide II bands), etc.; and that the active groups must serve as nucleation sites for Au(0) nuclei growth. A further investigation on the interactions of each of the soluble hydrolysates of D01, Bacillus licheniformis R08, Lactobacillus sp. strain A09 and waste Saccharomyces cerevisiae biomasses with Au(III) by IR spectrometry clearly reveals an essential biomacromolecule-characteristic that seems the binding of Au(III) to the oxygen of the peptide bond has caused a significant, molecular conformation-rearrangement in polypeptide backbones from β-pleated sheet to α-helices and/or β-turns of protein secondary structure; and that this changing appears to be accompanied by the occurrence, in the peptide bond, of much unbound -C=O and H-N- groups, being freed from the inter-molecular hydrogen-bonding of the β-pleated sheet and carried on the helical forms, as well as by the alternation in side chain steric positions of protein primary structure. This might be reasonably expected to result in higher-affinity interactions of peptide bond and side chains with Au(III).

Conclusions

The evidence suggests that the polypeptides appear to be activated by the intervention of Au(III) via the molecular reconformation and in turn react upon Au(III) actively and exert profound impacts on the course of Au(0) nucleation and crystal growth.

Microcalorimetric and potentiometric titration studies on the adsorption of copper by P. putida and B. thuringiensis and their composites with minerals

In order to have a better understanding of the interactions of heavy metals with bacteria and minerals in soil and associated environments, isothermal titration calorimetry (ITC), potentiometric titration and equilibrium sorption experiments were conducted to investigate the adsorption behavior of Cu(II) by Bacillus thuringiensis, Pseudomonas putida and their composites with minerals. The interaction of montmorillonite with bacteria increased the reactive sites and resulted in greater adsorption for Cu(II) on their composites, while decreased adsorption sites and capacities for Cu(II) were observed on goethite-bacteria composites. A gram-positive bacterium B. thuringiensis played a more important role than a gram-negative bacterium P. putida in determining the properties of the bacteria-minerals interfaces. The enthalpy changes (DeltaH(ads)) from endothermic (6.14 kJ mol(-1)) to slightly exothermic (-0.78 kJ mol(-1)) suggested that Cu(II) is complexed with the anionic oxygen ligands on the surface of bacteria-mineral composites. Large entropies (32.96-58.89 J mol(-1) K(-1)) of Cu(II) adsorption onto bacteria-mineral composites demonstrated the formation of inner-sphere complexes in the presence of bacteria. The thermodynamic data implied that Cu(II) mainly bound to the carboxyl and phosphoryl groups as inner-sphere complexes on bacteria and mineral-bacteria composites.

Use of Algae for Removing Heavy Metal Ions From Wastewater: Progress and Prospects

Many algae have immense capability to sorb metals, and there is considerable potential for using them to treat wastewaters. Metal sorption involves binding on the cell surface and to intracellular ligands. The adsorbed metal is several times greater than intracellular metal. Carboxyl group is most important for metal binding. Concentration of metal and biomass in solution, pH, temperature, cations, anions and metabolic stage of the organism affect metal sorption. Algae can effectively remove metals from multi-metal solutions. Dead cells sorb more metal than live cells. Various pretreatments enhance metal sorption capacity of algae. CaCl2 pretreatment is the most suitable and economic method for activation of algal biomass. Algal periphyton has great potential for removing metals from wastewaters. An immobilized or granulated biomass-filled column can be used for several sorption/desorption cycles with unaltered or slightly decreased metal removal. Langmuir and Freundlich models, commonly used for fitting sorption data, cannot precisely describe metal sorption since they ignore the effect of pH, biomass concentration, etc. For commercial application of algal technology for metal removal from wastewaters, emphasis should be given to: (i) selection of strains with high metal sorption capacity, (ii) adequate understanding of sorption mechanisms, (iii) development of low-cost methods for cell immobilization, (iv) development of better models for predicting metal sorption, (v) genetic manipulation of algae for increased number of surface groups or over expression of metal binding proteins, and (vi) economic feasibility.

Application of a magnetotactic bacterium, Stenotrophomonas sp. to the removal of Au(III) from contaminated wastewater with a magnetic separator

In this study, the feasibility of applying a magnetotactic bacterial isolate (MTB), Stenotrophomonas sp. to the removal of Au(III) was investigated. Biosorption experiments showed that Au(III) biosorption capacity exhibited no significant difference in the initial pH range of 1.0-5.5, while decreased more significantly in the initial pH range of 5.5-13.0. Langmuir isotherm indicated that the maximum Au(III) biosorption capacity of Stenotrophomonas sp. were 506, 369 and 308 mg g(-1) dry weight biomass at the initial pH values of 2.0, 7.0 and 12.0, respectively. Thiourea was proved to be an effective desorbent to recover Au from the MTB biomass and 91% Au adsorbed on the biomass could be recovered at equilibrium when the thiourea concentration was 0.8M. The magnetic separator developed by our research team used for separating Au loaded MTB biomass showed high separation efficiency, with 100% biomass removed at the magnetic intensity of 1200 Gs in 180 min. The analyses from FTIR and XRD further confirmed that the reduction of Au(III) to Au(0) by the reductants on the MTB biomass occurred, and the deposition of nano-crystal Au(0) particles, ranging from 24.7 to 31.4 nm, could be estimated on the biomass surface.

Biorecovery of gold by Escherichia coli and Desulfovibrio desulfuricans

Microbial precipitation of gold was achieved using Escherichia coli and Desulfovibrio desulfuricans provided with H2 as the electron donor. No precipitation was observed using H2 alone or with heat-killed cells. Reduction of aqueous AuIII ions by both strains was demonstrated at pH 7 using 2 mM HAuCl4 solution and the concept was successfully applied to recover 100% of the gold from acidic leachate (115 ppm of AuIII) obtained from jewelry waste. Bioreductive recovery of gold from aqueous solution was achieved within 2 h, giving crystalline Au0 particles (20-50 nm), in the periplasmic space and on the cell surface, and small intracellular nanoparticles. The nanoparticle size was smaller (red suspension) at acidic pH (2.0) as compared to that obtained at pH 6.0 and 7.0 (purple) and 9.0 (dark blue). Comparable nanoparticles were obtained from AuIII test solutions and jewelry leachate.

Formation of metallic copper nanoparticles at the soil-root interface

Copper is an essential element in the cellular electron-transport chain, but as a free ion it can catalyze production of damaging radicals. Thus, all life forms attempt to prevent copper toxicity. Plants diminish excess copper in two structural regions: rare hyperaccumulators bind cationic copper to organic ligands in subaerial tissues, whereas widespread metal-tolerant plants segregate copper dominantly in roots by mechanisms thought to be analogous. Here we show using synchrotron microanalyses that common wetlands plants Phragmites australis and Iris pseudoacorus can transform copper into metallic nanoparticles in and near roots with evidence of assistance by endomycorrhizal fungi when grown in contaminated soil in the natural environment. Biomolecular responses to oxidative stress, similar to reactions used to abiotically synthesize Cu0 nanostructures of controlled size and shape, likely cause the transformation. This newly identified mode of copper biomineralization by plant roots under copper stress may be common in oxygenated environments.

Microbial and plant derived biomass for removal of heavy metals from wastewater

Discharge of heavy metals from metal processing industries is known to have adverse effects on the environment. Conventional treatment technologies for removal of heavy metals from aqueous solution are not economical and generate huge quantity of toxic chemical sludge. Biosorption of heavy metals by metabolically inactive non-living biomass of microbial or plant origin is an innovative and alternative technology for removal of these pollutants from aqueous solution. Due to unique chemical composition biomass sequesters metal ions by forming metal complexes from solution and obviates the necessity to maintain special growth-supporting conditions. Biomass of Aspergillus niger, Penicillium chrysogenum, Rhizopus nigricans, Ascophyllum nodosum, Sargassum natans, Chlorella fusca, Oscillatoria anguistissima, Bacillus firmus and Streptomyces sp. have highest metal adsorption capacities ranging from 5 to 641 mg g(-1) mainly for Pb, Zn, Cd, Cr, Cu and Ni. Biomass generated as a by-product of fermentative processes offers great potential for adopting an economical metal-recovery system. The purpose of this paper is to review the available information on various attributes of utilization of microbial and plant derived biomass and explores the possibility of exploiting them for heavy metal remediation.

Biorecovery of Gold from Jewellery Wastes by Escherichia Coli and Biomanufacture of Active Au-Nanomaterial

Microbial reduction of Au(III) from HAuCl4 was demonstrated. Escherichia coli and Desulfovibrio desulfuricans reduced 1 mM Au(III) in 60 and 120 min at pH 6.9 and 2.3 respectively. TEM and elemental analysis showed the formation of Au(0) nanoparticles and their pH-dependent cellular localisation. The concept was applied to the recovery of gold from jewellery waste leachates using E. coli. Bio-Au(0) nanoparticles were tested for catalytic activity in the oxidation of glycerol, achieving 30% conversion to glyceric acid. A simple bioprocess for conversion of waste to new material is suggested.

Competitive metal binding to a silicate-immobilized humic material

The investigation of the competitive binding of metal ions to a biogenic material comprised of organic peat immobilized in a polysilicate matrix was undertaken. This material was packed into 5.0mL bed-volume columns using 40-60mesh size particles. Two separate mixtures of metal ions were studied by monitoring the solution pH and the concentration of each metal in the effluent as a function of the volume of influent introduced to the material. These mixtures contained either the metal ions Ca(2+), Mg(2+), and Cu(2+) or the ions Cu(2+), Hg(2+), and Pb(2+). A general order of binding affinities was determined to be Mg(2+)<Ca(2+)<<Cu(2+)<Pb(2+)<Hg(2+). Comparisons of amounts of metal ions bound and protons released indicated the initial release of two protons for each divalent metal ion bound. However, prolonged exposure of the material to the metal solutions yielded a molar ratio of 1:1. This suggests the involvement of ion exchange sites followed by that of sites using an alternate binding mechanism. The presence of binding sites with varied mechanisms and metal ion affinities was further illustrated through the initial binding and subsequent release of lower affinity metal ions (e.g., Mg(2+) and Ca(2+)).