Nature of Activated Manganese Oxide for Oxygen Evolution

Ligand-rich oxygen evolution electrocatalysts reconstructed from metal-organic frameworks for anion-exchange membrane water electrolysis

Organic ligands in metal-organic frameworks (MOFs) play an indispensable role in the reconstruction and catalysis during the alkaline oxygen evolution reaction (OER). However, it is still a big challenge to maintain a high content of ligands in MOF-reconstructed OER electrocatalysts and to study the interaction between ligands and derived (oxy)hydroxides. Herein, a ligand-rich trimetallic amorphous electrocatalyst is fabricated through a two-step mechanochemical and electrochemical reconstruction strategy. Experimental and theoretical studies clearly reveal that the d-π interaction between delocalized π-electrons on the benzene ring of ligands and derived (oxy)hydroxides, can trigger the charge transfer from ligands to the active metal centers, thus optimizing the adsorption energy of the oxygen-containing intermediates and enhancing the OER performance. Moreover, an anion-exchange membrane water electrolyzer using such ligand-rich OER electrocatalyst can be operated steadily at 1.69 V and 55 °C under an industrial-level current density of 500 mA cm-2 for over 200 h. This work provides novel insights into the role of organic ligands in alkaline OER electrocatalysis, with the potential to facilitate the production of green hydrogen at industrial-level current densities.

Modulating Intrinsic Sulfate Ions in FeOOH Nanorods for Enhanced Energy Storage and Catalytic Oxygen Evolution

Designing efficient low-cost earth-abundant metal electrodes for enhanced energy storage and sluggish oxygen evolution reactions (OERs) poses significant challenges in electrochemistry. Herein an innovative approach to boost the activity of FeOOH nanorods for energy storage and catalytic OER by initiating intrinsic sulfate ion (SO4 2-) modulation is proposed. Through a one-step hydrothermal synthesis using a polymeric ferric sulfate precursor, it is successfully cultivated sulfated iron oxyhydroxide (S-FeOOH) nanorods. Remarkably, the presence of sulfate ions effectively prevented the transformation of FeOOH into less active Fe2O3, even under elevated temperature. Annealing induced the leaching of sulfate ions, leading to structural rearrangements with shorter Fe-O bond lengths and the formation of sulfate-textured FeOOH (ST-FeOOH) with additional active sites, consequently increasing the material's surface area. Importantly, compared with reported non-noble metal catalysts, the ST-FeOOH nanorods exhibited significantly enhanced energy storage capabilities (3684 mF cm-2) and catalytic performance in the OER. With a low overpotential of 173 mV to achieve a current density of 10 mA cm-2, fast OER kinetics (39 mV dec-1), and exceptional stability exceeding 80 h, these nanorods demonstrate their potential as efficient OER catalysts. This work demonstrates sulfate ion modulation's role in tailoring FeOOH nanorods for advanced cost-effective electrodes and OER electrocatalysts.

Electrodeposited Manganese Dioxides and Their Composites as Electrocatalysts for Energy Conversion Reactions

Enhancing the efficiencies of electrochemical reactions for converting renewable energy into clean chemical fuels as well as generating clean energy is critical to achieving carbon neutrality. However, this enhancement can be achieved using materials that are not constrained by resource limitations and those that can be converted into devices in a scalable manner, preferably for industrial applications. This review explores the applications of electrochemically deposited manganese dioxides (MnO2) and their composites as electrochemical catalysts for oxygen evolution (OER) and hydrogen evolution reactions for converting renewable energy into chemical fuels. It also explores their applications as electrochemical catalysts for oxygen reduction reaction (ORR) and bifunctional OER/ORR for the efficient operation of fuel cells and metal-air batteries, respectively. Manganese is the second most abundant transition metal in the Earth's crust, and electrodeposition represents a binder-free and scalable technique for fabricating devices (electrodes). To propose an improved catalyst design, the studies on the electrodeposition mechanism of MnO2 as well as the fabrication techniques for MnO2-based nanocomposites accumulated in the development of electrodes for supercapacitors are also included in this review.

Noble-metal-free catalysts for the oxygen evolution reaction in acids

Oxygen evolution catalysts are critical components of proton exchange membrane water electrolysers (PEMWEs), playing a decisive role in determining both the performance and cost of these devices. Non-noble metal-based oxygen evolution catalysts have recently drawn significant attention as potential alternatives to expensive noble metal catalysts. This review systematically summarizes the mechanism of non-noble metal catalysts for the oxygen evolution reaction in acids with respect to their activity and stability, incorporating theoretical calculations and the Pourbaix diagram. Advanced in situ techniques are highlighted as powerful tools for probing intermediate evolution and valence changes and further elucidating the catalytic mechanism. Furthermore, key strategies for enhancing catalytic activity and durability, such as elemental doping, the support effect, surface protection and novel phase design, are discussed. Finally, this review provides insights into the remaining challenges and emerging opportunities for advancing practical oxygen evolution catalysts in PEMWEs.

Morphology-Driven Bifunctional Activity of Layered Birnessite-Based Materials toward Oxygen Electrocatalysis

The chemical, structural, and morphological diversity of birnessite, a 2D layered MnO2, has opened avenues for its application as an electrocatalyst toward both the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER). Among pristine birnessites prepared by different methods, the freestanding flakes (primary structure) obtained from molten salt (MS-KMnO) showed remarkable bifunctional activity as compared to samples with thicker plates or a hierarchical honeycomb-like (type-I secondary structure) morphology. While the ORR onset potential (E onset) and halfwave potential (E 1/2) for MS-KMnO were recorded at 0.89 and 0.81 V vs RHE, respectively, the OER overpotential (η) was found to be 300 mV. We demonstrated heat-induced secondary structure evolution by modification of the molten salt method, which led to a decrease in activity. In contrast to previous studies, the Co-doped birnessite (Co-KMnO) prepared in molten salt showed lower bifunctional activity (ORR, E 1/2 = 0.72 V; OER, η= 460 mV) as compared to MS-KMnO. Co-KMnO showed an interwoven wrinkled sheet-like (type-II secondary structure) morphology, with Co3+ present in both the in-layer and the interlayer. However, in Co-KMnO/360 prepared at a lower reaction temperature, the areal coverage of the type-II structure reduces, leading to an increase in ORR (E 1/2 = 0.76 V) and OER (η = 440 mV) activity. The chronopotentiometry for 100 h at a constant OER current of 50 mA cm-2 showed an increase in potential from 1.62 to 1.89 V and the characterization of the sample post-treatment showed degradation of the layered structure in MS-KMnO. The samples obtained after 1000 CV cycles in both the ORR and the OER regions showed the formation of secondary structures with a substantial decrease in the Mn3+/Mn4+ ratio. This study demonstrates that morphology tuning within the 2D birnessite system has a marked effect on its bifunctional activity.

Advances in Two-Electron Water Oxidation Reaction for Hydrogen Peroxide Production: Catalyst Design and Interface Engineering

Hydrogen peroxide (H2O2) is a versatile and zero-emission material that is widely used in the industrial, domestic, and healthcare sectors. It is clear that it plays a critical role in advancing environmental sustainability, acting as a green energy source, and protecting human health. Conventional production techniques focused on anthraquinone oxidation, however, electrocatalytic synthesis has arisen as a means of utilizing renewable energy sources in conjunction with available resources like oxygen and water. These strides represent a substantial change toward more environmentally and energy-friendly H2O2 manufacturing techniques that are in line with current environmental and energy goals. This work reviews recent advances in two-electron water oxidation reaction (2e-WOR) electrocatalysts, including design principles and reaction mechanisms, examines catalyst design alternatives and experimental characterization techniques, proposes standardized assessment criteria, investigates the impact of the interfacial milieu on the reaction, and discusses the value of in situ characterization and molecular dynamics simulations as a supplement to traditional experimental techniques and theoretical simulations. The review also emphasizes the importance of device design, interface, and surface engineering in improving the production of H2O2. Through adjustments to the chemical microenvironment, catalysts can demonstrate improved performance, opening the door for commercial applications that are scalable through tandem cell development.

Electronic Synergistic Effects on the Stability and Oxygen Evolution Reaction Efficiency of the Mesoporous LiMn2-xMxO4 (M = Mn, Fe, Co, Ni, and Cu) Electrodes

Stable porous manganese oxide-based electrodes are essential for clean energy generation and storage because of their high natural abundance and health safety. This investigation focuses on mesoporous LiMn2-xMxO4 (where M is Fe, Co, Ni, and Cu and x is 0, 0.1, 0.3, 0.5, and 0.67) electrodes and thin/thick films. The mesoporous electrodes and films are fabricated by coating clear and homogeneous ethanol solutions of the salts (LiNO3, [Mn(OH2)4](NO3)2, and [M(OH2)x](NO3)2) and surfactants (P123 and CTAB) and calcining at elevated temperature (denoted as F-LiMn2-xMxO4, G-LiMn2-xMxO4, and meso-LiMn2-xMxO4, respectively). The electrochemical properties, stability, and oxygen evolution reaction (OER) performance of the F/G-LiMn2-xMxO4 electrodes are investigated in alkaline media using a three electrode setup. The F-LiMn1.33M0.67O4 electrodes (where M is Mn, Fe, Co, and Ni) exhibit low Tafel slopes of 60, 43, 44, and 32 mV/dec, respectively. While all the Mn-rich and F-LiMn2-xFexO4 electrodes degrade via Mn(VI) disproportionation reaction, the 33% Co electrode shows high stability during the OER. The nickel-based electrodes are stable with as little as 15% Ni and display excellent OER performance over 25% Ni, albeit undergoing a transformation that accumulates Ni(OH)2 species on the electrode surface. Copper in the F-LiMn2-xCuxO4 electrodes is homogeneous at low Cu percentages but forms a CuO phase above 15% Cu, undergoes degradation, and displays a weak OER performance. In short, Co and Ni stabilize the F-LiMn1.33Co0.67O4 and F-LiMn1.7Ni0.3O4 electrodes, which display excellent OER performance.

Non-Noble-Metal-Based Electrocatalysts for Acidic Oxygen Evolution Reaction: Recent Progress, Challenges, and Perspectives

The oxygen evolution reaction (OER) plays a pivotal role in diverse renewable energy storage and conversion technologies, including water electrolysis, electrochemical CO2 reduction, nitrogen fixation, and metal-air batteries. Among various water electrolysis techniques, proton exchange membrane (PEM)-based water electrolysis devices offer numerous advantages, including high current densities, exceptional chemical stability, excellent proton conductivity, and high-purity H2. Nevertheless, the prohibitive cost associated with Ir/Ru-based OER electrocatalysts poses a significant barrier to the broad-scale application of PEM-based water splitting. Consequently, it is crucial to advance the development of non-noble metal OER catalysis substance with high acid-activity and stability, thereby fostering their widespread integration into PEM water electrolyzers (PEMWEs). In this review, a comprehensive analysis of the acidic OER mechanism, encompassing the adsorbate evolution mechanism (AEM), lattice oxygen mechanism (LOM) and oxide path mechanism (OPM) is offered. Subsequently, a systematic summary of recently reported noble-metal-free catalysts including transition metal-based, carbon-based and other types of catalysts is provided. Additionally, a comprehensive compilation of in situ/operando characterization techniques is provided, serving as invaluable tools for furnishing experimental evidence to comprehend the catalytic mechanism. Finally, the present challenges and future research directions concerning precious-metal-free acidic OER are comprehensively summarized and discussed in this review.

Electrocatalysis of Oxygen Evolution Reaction Promoted by CoNiMn Films Synthesized by Electrodeposition

Recently, efforts have been made to address the environmental damage caused by fossil-fuel-based primary energy sources. Interest in efficient technologies for converting and storing energy using renewable sources, especially sunlight, has increased, with the aim of replicating the natural photosynthesis process. However, artificial photosynthesis faces challenges with unfavorable kinetics and thermodynamics, requiring the use of stable catalysts for the hydrogen evolution (HER) and oxygen evolution (OER) reactions to generate H2 and O2, respectively. OER is the most prohibitive of the half-reactions by the highly sluggish kinetics. Mixed oxides, particularly those based on first-row transition metals, have shown promising results as catalysts for the OER. This work reports the synthesis of CoNiMn oxide via electrodeposition on fluoride tin oxide followed by electrochemical activation. This approach seeks to explore the synergistic effect between the elements and to produce a catalyst with superior efficiency and stability for the electrocatalysis of the OER compared to the monometallic and bimetallic oxides. The CoNiMn film was structurally and electrochemically characterized. The electrodeposited CoNiMn hybrid films demonstrated low overpotentials compared with standard OER electrocatalysts, with CoNiMn films outperforming all single and bimetallic oxide films. The activated CoNiMn film required an overpotential of 100 mV at 10 mA cm-2 (430 mV at 25 mA cm-2) and Tafel slope of 58 mV dec-1. The film was active for 15 h at 100 mA cm-2 and showed no significant change in morphology and structure after the chronopotentiometry, indicating that it is a promising and cost-effective alternative to enhance the OER activity using abundant elements.

MOF-derived three-dimensional porous dodecahedral structured bimetallic Mn/Co-C-N composite for high-performance durable oxygen reduction reaction electrocatalysts

Investigating high-efficiency oxygen reduction reaction (ORR) catalysts is one of the most effective methods for addressing the sluggish kinetics at the fuel cell cathode. Bimetallic three-dimensional porous materials have garnered significant attention due to their diverse structures, large specific surface area and synergistic catalytic effects. Herein, we synthesized a bimetallic three-dimensional porous dodecahedral structure, Mn/Co-C-N, derived from MOF using a straightforward approach. Experimental reults confirm that the strategic incorporation of Mn enhances the electrocatalytic activity for ORR. Meanwhile, the synergistic effects of Mn and Co, as well as the advantages of the dodecahedral structure for expediting electron transfer, all contribute to the exceptional ORR performance. Arc testing in an alkaline electrolyte reveals that the initial potential (Eonset) and the half-wave potential (E1/2) are 0.89 V and 0.80 V, closely approximating those of commercial Pt/C (20 wt%). Following 10 000 stability test cycles, the half-wave potential exhibits a mere 8 mV change, confirming its remarkable stability.

Multifunctional Design of Catalysts for Seawater Electrolysis for Hydrogen Production

Direct seawater electrolysis is a promising technology within the carbon-neutral energy framework, leveraging renewable resources such as solar, tidal, and wind energy to generate hydrogen and oxygen without competing with the demand for pure water. High-selectivity, high-efficiency, and corrosion-resistant multifunctional electrocatalysts are essential for practical applications, yet producing stable and efficient catalysts under harsh conditions remains a significant challenge. This review systematically summarizes recent advancements in advanced electrocatalysts for seawater splitting, focusing on their multifunctional designs for selectivity and chlorine corrosion resistance. We analyze the fundamental principles and mechanisms of seawater electrocatalytic reactions, discuss the challenges, and provide a detailed overview of the progress in nanostructures, alloys, multi-metallic systems, atomic dispersion, interface engineering, and functional modifications. Continuous research and innovation aim to develop efficient, eco-friendly seawater electrolysis systems, promoting hydrogen energy application, addressing efficiency and stability challenges, reducing costs, and achieving commercial viability.

Ultrafine Nanoclusters Unlocked 3d-4f Electronic Ladders for Efficient Electrocatalytic Water Oxidation

The vast extensional planes of two-dimensional (2D) nanomaterials are recognized as desirable ground for electrocatalytic reactions. However, they tend to exhibit catalytic inertia due to their surface-ordered coordination configurations. Herein, an in situ autoxidation strategy enables high-density grafting of ultrafine CeO2 nanoclusters on 2D Co(OH)2. Affluent active units were activated at the inert interface of Co(OH)2 via the formation of Co-O-Ce units. The optimized catalyst exhibits oxygen evolution reaction activity with an overpotential of 83 mV lower than that of Co(OH)2 at 10 mA cm-2. The cascade orbital coupling between Co (3d) and Ce (4f) in Co-O-Ce units drives electron transfer by unlocking a "d-f electron ladder". Meanwhile, the bond-order theorem analyses and the d-band center show that the occupancy of Co-3d-eg is optimized to balance the adsorption-desorption process of active sites to the key reaction intermediate *OOH, thereby making it easier to release oxygen. This work will drive the development of wider area electron modulation methods and provide guidance for the surface engineering of 2D nanomaterials.

Facile synthesis of nanostructured Ni/NiO/N-doped graphene electrocatalysts for enhanced oxygen evolution reaction

Electrocatalysts containing a Ni/NiO/N-doped graphene interface have been synthesised using the ligand-assisted chemical vapor deposition technique. NiO nanoparticles were used as the substrate to grow N-doped graphene by decomposing vapours of benzene and N-containing ligands. The method was demonstrated with two nitrogen-containing ligands, namely dipyrazino[2,3-f:2',3'-h]quinoxaline-2,3,6,7,10,11-hexacarbonitrile (L) and melamine (M). The structure and composition of the as-synthesized composites were characterized by XRD, Raman spectroscopy, SEM, TEM and XPS. The composite prepared using the ligand L had NiO sandwiched between Ni and N-doped graphene and showed an overpotential of 292 mV at 10 mA cm-2 and a Tafel slope of 45.41 mV dec-1 for the OER, which is comparable to the existing noble metal catalysts. The composite prepared using the ligand M had Ni encapsulated by N-doped graphene without NiO. It showed an overpotential of 390 mV at 10 mA cm-2 and a Tafel slope of 78.9 mV dec-1. The ligand-assisted CVD route demonstrates a facile route to control the microstructure of the electrocatalysts.

Charge Transfer Mechanism on a Cobalt-Polyoxometalate-TiO2 Photoanode for Water Oxidation in Acid

We constructed a photoanode comprising the homogeneous water oxidation catalyst (WOC) Na8K8[Co9(H2O)6(OH)3(HPO4)2(PW9O34)3] (Co9POM) and nanoporous n-type TiO2 photoelectrodes (henceforth "TiO2-Co9POM") by first anchoring the cationic 3-aminopropyltrimethoxysilane (APS) ligand on a metal oxide light absorber, followed by treatment of the metal oxide-APS with a solution of the polyoxometalate WOC. The resulting TiO2-Co9POM photoelectrode exhibits a 3-fold oxygen evolution photocurrent enhancement compared to bare TiO2 in aqueous acidic conditions. Three-element (Co 2p, W 4f, and O 1s) X-ray photoelectron spectroscopy and Raman spectroscopy studies before and after use indicate that surface-bound Co9POM retains its structural integrity throughout all photoelectrochemical water oxidation studies reported here. Extensive charge-transfer mechanistic studies by photoelectrochemical techniques and transient absorption spectroscopy elucidate that Co9POM serves as an efficient WOC, extracting photogenerated holes from TiO2 on the picosecond time scale. This is the first comprehensive mechanistic investigation elucidating the roles of polyoxometalates in POM-photoelectrode hybrid oxygen evolution reaction systems.

Deciphering Photoinduced Catalytic Reaction Mechanisms in Natural and Artificial Photosynthetic Systems on Multiple Temporal and Spatial Scales Using X-ray Probes

Utilization of renewable energies for catalytically generating value-added chemicals is highly desirable in this era of rising energy demands and climate change impacts. Artificial photosynthetic systems or photocatalysts utilize light to convert abundant CO2, H2O, and O2 to fuels, such as carbohydrates and hydrogen, thus converting light energy to storable chemical resources. The emergence of intense X-ray pulses from synchrotrons, ultrafast X-ray pulses from X-ray free electron lasers, and table-top laser-driven sources over the past decades opens new frontiers in deciphering photoinduced catalytic reaction mechanisms on the multiple temporal and spatial scales. Operando X-ray spectroscopic methods offer a new set of electronic transitions in probing the oxidation states, coordinating geometry, and spin states of the metal catalytic center and photosensitizers with unprecedented energy and time resolution. Operando X-ray scattering methods enable previously elusive reaction steps to be characterized on different length scales and time scales. The methodological progress and their application examples collected in this review will offer a glimpse into the accomplishments and current state in deciphering reaction mechanisms for both natural and synthetic systems. Looking forward, there are still many challenges and opportunities at the frontier of catalytic research that will require further advancement of the characterization techniques.

Operando studies of Mn oxide based electrocatalysts for the oxygen evolution reaction

Inspired by photosystem II (PS II), Mn oxide based electrocatalysts have been repeatedly investigated as catalysts for the electrochemical oxygen evolution reaction (OER), the anodic reaction in water electrolysis. However, a comparison of the conditions in biological OER catalysed by the water splitting complex CaMn4Ox with the requirements for an electrocatalyst for industrially relevant applications reveals fundamental differences. Thus, a systematic development of artificial Mn-based OER catalysts requires both a fundamental understanding of the catalytic mechanisms as well as an evaluation of the practicality of the system for industrial scale applications. Experimentally, both aspects can be approached using in situ and operando methods including spectroscopy. This paper highlights some of the major challenges common to different operando investigation methods and recent insights gained with them. To this end, vibrational spectroscopy, especially Raman spectroscopy, absorption techniques in the bandgap region and operando X-ray spectroelectrochemistry (SEC), both in the hard and soft X-ray regime are particularly focused on here. Technical challenges specific to each method are discussed first, followed by challenges that are specific to Mn oxide based systems. Finally, recent in situ and operando studies are reviewed. This analysis shows that despite the technical and Mn specific challenges, three specific key features are common to most of the studied systems with significant OER activity: structural disorder, Mn oxidation states between III and IV, and the appearance of layered birnessite phases in the active regime.

Light-Mediated Electrochemical Synthesis of Manganese Oxide Enhances Its Stability for Water Oxidation

New methods are needed to increase the activity and stability of earth-abundant catalysts for electrochemical water splitting to produce hydrogen fuel. Electrodeposition has been previously used to synthesize manganese oxide films with a high degree of disorder and a mixture of oxidation states for Mn, which has led to electrocatalysts with high activity but low stability for the oxygen evolution reaction (OER) at high current densities. In this study, we show that multipotential electrodeposition of manganese oxide under illumination produces nanostructured films with significantly higher stability for the OER compared to films grown under otherwise identical conditions in the dark. Manganese oxide films grown by multipotential deposition under illumination sustain a current density of 10 mA/cm2 at 2.2 V versus reversible hydrogen electrode for 18 h (pH 13). Illumination does not enhance the activity or stability of manganese oxide films grown using a constant potential, and films grown by multipotential deposition in the dark undergo a complete loss of activity within 1 h of electrolysis. Electrochemical and structural characterization indicate that photoexcitation of the films during growth reduces Mn ions and changes the content and structure of intercalated potassium ions and water molecules in between the disordered layers of birnessite-like sheets of MnOx, which stabilizes the nanostructured film during electrocatalysis. These results demonstrate that combining multiple external stimuli (i.e., light and an external potential) can induce structural changes not attainable by either stimulus alone to make earth-abundant catalysts more active and stable for important chemical transformations such as water oxidation.

Breaking the Activity and Stability Bottlenecks of Electrocatalysts for Oxygen Evolution Reactions in Acids

Oxygen evolution reaction (OER) is a cornerstone reaction for a variety of electrochemical energy conversion and storage systems such as water splitting, CO2 /N2 reduction, reversible fuel cells, and metal-air batteries. However, OER catalysis in acids suffers from extra sluggish kinetics due to the additional step of water dissociation along with its multiple electron transfer processes. Furthermore, OER catalysts often suffer from poor stability in harsh acidic electrolytes due to the severe dissolution/corrosion processes. The development of active and stable OER catalysts in acids is highly demanded. Here,  the recent advances in OER electrocatalysis in acids are reviewed and the key strategies are summarized to overcome the bottlenecks of activity and stability for both noble-metal-based and noble metal-free catalysts, including i) morphology engineering, ii) composition engineering, and iii) defect engineering. Recent achievements in operando characterization and theoretical calculations are summarized which provide an unprecedented understanding of the OER mechanisms regarding active site identification, surface reconstruction, and degradation/dissolution pathways. Finally, views are offered on the current challenges and opportunities to break the activity-stability relationships for acidic OER in mechanism understanding, catalyst design, as well as standardized stability and activity evaluation for industrial applications such as proton exchange membrane water electrolyzers and beyond.

Sequestration and oxidation of heavy metals mediated by Mn(II) oxidizing microorganisms in the aquatic environment

Microorganisms can oxidize Mn(II) to biogenic Mn oxides (BioMnOx), through enzyme-mediated processes and non-enzyme-mediated processes, which are generally considered as the source and sink of heavy metals due to highly reactive to sequestrate and oxidize heavy metals. Hence, the summary of interactions between Mn(II) oxidizing microorganisms (MnOM) and heavy metals is benefit for further work on microbial-mediated self-purification of water bodies. This review comprehensively summarizes the interactions between MnOM and heavy metals. The processes of BioMnOx production by MnOM has been firstly discussed. Moreover, the interactions between BioMnOx and various heavy metals are critically discussed. On the one hand, modes for heavy metals adsorbed on BioMnOx are summarized, such as electrostatic attraction, oxidative precipitation, ion exchange, surface complexation, and autocatalytic oxidation. On the other hand, adsorption and oxidation of representative heavy metals based on BioMnOx/Mn(II) are also discussed. Thirdly, the interactions between MnOM and heavy metals are also focused on. Finally, several perspectives which will contribute to future research are proposed. This review provides insight into the sequestration and oxidation of heavy metals mediated by Mn(II) oxidizing microorganisms. It might be helpful to understand the geochemical fate of heavy metals in the aquatic environment and the process of microbial-mediated water self-purification.

Mesoporous Manganese Oxides with High-Valent Mn Species and Disordered Local Structures for Efficient Oxygen Electrocatalysis

Active and nonprecious-metal bifunctional electrocatalysts for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) are vital components of clean energy conversion devices such as regenerative fuel cells and rechargeable metal-air batteries. Porous manganese oxides (MnO_x) are promising electrocatalyst candidates because of their high surface area and the abundance of Mn. MnO_x catalysts exhibit various oxidation states and crystal structures, which critically affect their electrocatalytic activity. These effects remain elusive mainly because the synthesis of oxidation-state-controlled porous MnO_x with similar structural properties is challenging. In this work, four different mesoporous manganese oxides (m-MnO_x) were synthesized and used as model catalysts to investigate the effects of local structures and Mn valence states on the activity toward oxygen electrocatalysis. The following activity trends were observed: m-Mn₂O₃ > m-MnO₂ > m-MnO > m-Mn₃O₄ for the ORR and m-MnO₂ > m-Mn₂O₃ > m-MnO ≈ m-Mn₃O₄ for the OER. These activity trends suggest that high-valent Mn species (Mn(III) and Mn(IV)) with disordered atomic arrangements induced by nanostructuring significantly influence electrocatalysis. In situ X-ray absorption spectroscopy was used to analyze the changes in the oxidation states under the ORR and OER conditions, which showed the surface phase transformation and generation of active species during electrocatalysis.

La- and Mn-doped cobalt spinel oxygen evolution catalyst for proton exchange membrane electrolysis

Discovery of earth-abundant electrocatalysts to replace iridium for the oxygen evolution reaction (OER) in a proton exchange membrane water electrolyzer (PEMWE) represents a critical step in reducing the cost for green hydrogen production. We report a nanofibrous cobalt spinel catalyst codoped with lanthanum (La) and manganese (Mn) prepared from a zeolitic imidazolate framework embedded in electrospun polymer fiber. The catalyst demonstrated a low overpotential of 353 millivolts at 10 milliamperes per square centimeter and a low degradation for OER over 360 hours in acidic electrolyte. A PEMWE containing this catalyst at the anode demonstrated a current density of 2000 milliamperes per square centimeter at 2.47 volts (Nafion 115 membrane) or 4000 milliamperes per square centimeter at 3.00 volts (Nafion 212 membrane) and low degradation in an accelerated stress test.

Fe(III) Docking-Activated Sites in Layered Birnessite for Efficient Water Oxidation

Non-noble metal catalysts for promoting the sluggish kinetics of oxygen evolution reaction (OER) are essential to efficient water splitting for sustainable hydrogen production. Birnessite has a local atomic structure similar to that of an oxygen-evolving complex in photosystem II, while the catalytic activity of birnessite is far from satisfactory. Herein, we report a novel Fe-Birnessite (Fe-Bir) catalyst obtained by controlled Fe(III) intercalation- and docking-induced layer reconstruction. The reconstruction dramatically lowers the OER overpotential to 240 mV at 10 mA/cm² and the Tafel slope to 33 mV/dec, making Fe-Bir the best of all the reported Bir-based catalysts, even on par with the best transition-metal-based OER catalysts. Experimental characterizations and molecular dynamics simulations elucidate that the catalyst features active Fe(III)-O-Mn(III) centers interfaced with ordered water molecules between neighboring layers, which lower reorganization energy and accelerate electron transfer. DFT calculations and kinetic measurements show non-concerted PCET steps conforming to a new OER mechanism, wherein the neighboring Fe(III) and Mn(III) synergistically co-adsorb OH* and O* intermediates with a substantially reduced O-O coupling activation energy. This work highlights the importance of elaborately engineering the confined interlayer environment of birnessite and more generally, layered materials, for efficient energy conversion catalysis.

Recent progress in noble-metal-free electrocatalysts for alkaline oxygen evolution reaction

The practical application of splitting water to generate hydrogen is to a large extent hindered by an oxygen evolution reaction (OER) process. Electrocatalysts with low-cost, high activity, and durability are essential for the low kinetic threshold of the OER. Despite the high active performances of noble metal compound electrocatalysts like IrO₂ and RuO₂, they are heavily restricted by the high cost and scarcity of noble metal elements. In this context, noble-metal-free electrocatalysts have acquired increasing significance in recent years. So far, a broad spectrum of noble-metal-free electrocatalysts has been developed for improved OER performance. In this review, three types of electrolysis and some evaluation criteria are introduced, followed by recent progress in designing and synthesizing noble-metal-free alkaline OER electrocatalysts, with the classification of metal oxides/(oxy)hydroxides, carbon-based materials, and metal/carbon hybrids. Finally, perspectives are also provided on the future development of the alkaline OER on active sites and stability of electrocatalysts.

Electrolyte Engineering for Oxygen Evolution Reaction Over Non-Noble Metal Electrodes Achieving High Current Density in the Presence of Chloride Ion

Direct seawater electrolysis potentially simplifies the electrolysis process and leads to a decrease in the cost of green hydrogen production. However, impurities present in the seawater, especially chloride ions (Cl- ), cause corrosion of the electrode material, and its oxidation competes with the anodic oxygen evolution reaction (OER). By carefully tuning electrode substrate and electrolyte solutions, the CoFeOx Hy /Ti electrode with high double-layer capacitance actively and stably electro-catalyzed the OER in potassium borate solutions at pH 9.2 in the presence of 0.5 mol kg-1 Cl- . The electrode possesses an active site motif composed of either a Co- or Fe-domain and benefits from an enlarged surface area. Selective OER was demonstrated in Cl- -containing electrolyte solutions at an elevated reaction temperature, stably achieving 500 mA cm-2 at a mere potential of 1.67 V vs. reversible hydrogen electrode (RHE) at 353 K for multiple on-off and long-term testing processes with a faradaic efficiency of unity toward the OER.

Tuning Electronic Structures of Transition Metal Carbides to Boost Oxygen Evolution Reactions in Acidic Medium

Developing low-cost, efficient, and robust nonprecious metal electrocatalysts for oxygen evolution reactions (OER) in acidic medium is the major challenge to realize the application of the proton exchange membrane water electrolyzer (PEM-WE). It is well-known that transition metal carbides (TMCs) have Pt-like electronic structures and catalytic behaviors. However, monometallic carbides in acidic medium show ignored OER activities. Herein, we reported that the catalytic activity of the TMCs can be enhanced by constructing bimetallic carbides (TiTaC₂) fabricated through hydrothermal treatment followed by an annealing process, and further by doping fluorine (F) into the bimetallic carbides (TiTaF_xC₂). The as-prepared reduced graphene oxide (rGO) supported TiTaF_xC₂ nanoparticles (TiTaF_xC₂ NP/rGO) show state-of-the-art OER catalytic activity, which is even superior to Ir/C catalyst (an onset potential of only 1.42 V vs RHE and the overpotential of 490 mV to reach 100 mA cm^-2), fast kinetics (Tafel slope of only 36 mV dec^-1), and high durability (maintaining the current density at 1.60 V vs RHE for 40 h). Detailed structural characterizations together with density functional theory (DFT) calculations reveal that the electronic structures of the bimetallic carbides have been tuned, and their possible mechanism is also discussed.

Stabilization of a Mn-Co Oxide During Oxygen Evolution in Alkaline Media

Improving the stability of electrocatalysts for the oxygen evolution reaction (OER) through materials design has received less attention than improving their catalytic activity. We explored the effects of Mn addition to a cobalt oxide for stabilizing the catalyst by comparing single phase CoOx and (Co0.7Mn0.3)Ox films electrodeposited in alkaline solution. The obtained disordered films were classified as layered oxides using X-ray absorption spectroscopy (XAS). The CoOx films showed a constant decrease in the catalytic activity during cycling, confirmed by oxygen detection, while that of (Co0.7Mn0.3)Ox remained constant within error as measured by electrochemical metrics. These trends were rationalized based on XAS analysis of the metal oxidation states, which were Co2.7+ and Mn3.7+ in the bulk and similar near the surface of (Co0.7Mn0.3)Ox, before and after cycling. Thus, Mn in (Co0.7Mn0.3)Ox successfully stabilized the bulk catalyst material and its surface activity during OER cycling. The development of stabilization approaches is essential to extend the durability of OER catalysts.

Why Did Nature Choose Manganese over Cobalt to Make Oxygen Photosynthetically on the Earth?

All contemporary oxygenic phototrophs─from primitive cyanobacteria to complex multicellular plants─split water using a single invariant cluster comprising Mn₄CaO₅ (the water oxidation catalyst) as the catalyst within photosystem II, the universal oxygenic reaction center of natural photosynthesis. This cluster is unstable outside of PSII and can be reconstituted, both in vivo and in vitro, using elemental aqueous ions and light, via photoassembly. Here, we demonstrate the first functional substitution of manganese in any oxygenic reaction center by in vitro photoassembly. Following complete removal of inorganic cofactors from cyanobacterial photosystem II microcrystal (PSIIX), photoassembly with free cobalt (Co²⁺), calcium (Ca²⁺), and water (OH^-) restores O₂ evolution activity. Photoassembly occurs at least threefold faster using Co²⁺ versus Mn²⁺ due to a higher quantum yield for PSIIX-mediated charge separation (P*): Co²⁺ → P* → Co³⁺Q_A^-. However, this kinetic preference for Co²⁺ over native Mn²⁺ during photoassembly is offset by significantly poorer catalytic activity (∼25% of the activity with Mn²⁺) and ∼3- to 30-fold faster photoinactivation rate. The resulting reconstituted Co-PSIIX oxidizes water by the standard four-flash photocycle, although they produce 4-fold less O₂ per PSII, suggested to arise from faster charge recombination (Co³⁺Q_A ← Co⁴⁺Q_A^-) in the catalytic cycle. The faster photoinactivation of reconstituted Co-PSIIX occurs under anaerobic conditions during the catalytic cycle, suggesting direct photodamage without the involvement of O₂. Manganese offers two advantages for oxygenic phototrophs, which may explain its exclusive retention throughout Darwinian evolution: significantly slower charge recombination (Mn³⁺Q_A ← Mn⁴⁺Q_A^-) permits more water oxidation at low and fluctuating solar irradiation (greater net energy conversion) and much greater tolerance to photodamage at high light intensities (Mn⁴⁺ is less oxidizing than Co⁴⁺). Future work to identify the chemical nature of the intermediates will be needed for further interpretation.

Sacrificial W Facilitates Self-Reconstruction with Abundant Active Sites for Water Oxidation

Water oxidation is an important reaction for multiple renewable energy conversion and storage-related devices and technologies. High-performance and stable electrocatalysts for the oxygen evolution reaction (OER) are urgently required. Bimetallic (oxy)hydroxides have been widely used in alkaline OER as electrocatalysts, but their activity is still not satisfactory due to insufficient active sites. In this research, A unique and efficient approach of sacrificial W to prepare CoFe (oxy)hydroxides with abundant active species for OER is presented. Multiple ex situ and operando/in situ characterizations have validated the self-reconstruction of the as-prepared CoFeW sulfides to CoFe (oxy)hydroxides in alkaline OER with synchronous W etching. Experiments and theoretical calculations show that the sacrificial W in this process induces metal cation vacancies, which facilitates the in situ transformation of the intermediate metal hydroxide to CoFe-OOH with more high-valence Co(III), thus creating abundant active species for OER. The Co(III)-rich environment endows the in situ formed CoFe oxyhydroxide with high catalytic activity for OER on a simple flat glassy carbon electrode, outperforming those not treated by the sacrificial W procedure. This research demonstrates the influence of etching W on the electrocatalytic performance, and provides a low-cost means to improve the active sites of the in situ self-reconstructed bimetallic oxyhydroxides for OER.

Self-healing oxygen evolution catalysts

Electrochemical and photoelectrochemical water splitting offers a scalable approach to producing hydrogen from renewable sources for sustainable energy storage. Depending on the applications, oxygen evolution catalysts (OECs) may perform water splitting under a variety of conditions. However, low stability and/or activity present challenges to the design of OECs, prompting the design of self-healing OECs composed of earth-abundant first-row transition metal oxides. The concept of self-healing catalysis offers a new tool to be employed in the design of stable and functionally active OECs under operating conditions ranging from acidic to basic solutions and from a variety of water sources.

Large scale sustainable energy storage by water splitting benefits from performing the oxygen evolution reaction under a variety of conditions. Here, the authors discuss self-healing catalysis as a new tool in the design of stable and functionally active catalysts in acidic to basic solutions, and a variety of water sources

Oxygen evolving reactions catalyzed by different manganese oxides: the role of oxidation state and specific surface area

A set of the four manganese oxide powders α-MnO2 (hollandite), δ-MnO2 (birnessite), Mn2O3 (bixbyite), and Mn3O4 (hausmannite) have been synthesized in a phase-pure form and tested as catalysts in three different oxygen evolution reactions (OER): electrochemical OER in KOH (1 mol L−1), chemical OER using aqueous cerium ammonium nitrate, and H2O2 decomposition. The trends in electrochemical (hollandite >> bixbyite > birnessite > hausmannite) and chemical OER (hollandite > birnessite > bixbyite > hausmannite) are different, which can be explained by differences in electric conductivity. H2O2 decomposition and chemical OER, on the other hand, showed the same trend and even a linear correlation of their initial OER rates. A linear correlation between the catalytic performance and the manganese oxidation state of the catalysts was observed. Another trend was observed related to the specific surface area, highlighting the importance of these properties for the OER. Altogether, hollandite was found to be the best performing catalyst in this study due to a combination of the high manganese oxidation state and a large specific surface area. Likely, due to a sufficient electrical conductivity, this intrinsically high OER performance is also found to some extent in electrocatalysis for this specific example.

Proton-Coupled Electron Transfer: The Engine of Energy Conversion and Storage

Proton-coupled electron transfer (PCET) underpins energy conversion in chemistry and biology. Four energy systems are described whose discoveries are based on PCET: the water splitting chemistry of the Artificial Leaf, the carbon fixation chemistry of the Bionic Leaf-C, the nitrogen fixation chemistry of the Bionic Leaf-N and the Coordination Chemistry Flow Battery (CCFB). Whereas the Artificial Leaf, Bionic Leaf-C, and Bionic Leaf-N require strong coupling between electron and proton to reduce energetic barriers to enable high energy efficiencies, the CCFB requires complete decoupling of the electron and proton so as to avoid parasitic energy-wasting reactions. The proper design of PCET in these systems facilitates their implementation in the areas of (i) centralized large scale grid storage of electricity and (ii) decentralized energy storage/conversion using only sunlight, air and any water source to produce fuel and food within a sustainable cycle for the biogenic elements of C, N and P.

Influence of MnO2-Birnessite Microstructure on the Electrochemical Performance of Aqueous Zinc Ion Batteries

KxMnO2 materials with birnessite-type structure are synthetized by two different methods which make it possible to obtain manganese oxides with different degrees of crystallinity. The XPS results indicate that the sample obtained at high temperature (KMn8) exhibits a lower oxidation state for manganese ions as well as a denser morphology. Both characteristics could explain the lower capacity value obtained for this electrode. In contrast, the sample obtained at low temperature (KMn4) or by hydrothermal method presents a manganese oxidation state close to 4 and a more porous morphology. Indeed, in this case higher capacity values are obtained. At current density of 30 mA g−1, the KMn8, KMn4, and HKMn samples display a capacity retention of 88, 82, and 68%, respectively. The higher capacity loss obtained for the HKMn compound could be explained considering that the incorporation of Zn2+ in the structure gives rise to the stabilization of a ZnMn2O4 spinel-type phase. This compound is obtained in the discharge process but remains in the charge stage. Thus, when this spinel-type phase is obtained the capacity loss increases. Moreover, the stabilization of this phase is more favorable at low current rates where 100% of retention for all samples, before 50 cycles, was observed.

Surprisingly Low Reactivity of Layered Manganese Oxide toward Water Oxidation in Fe/Ni-Free Electrolyte under Alkaline Conditions

So far, many studies on the oxygen-evolution reaction (OER) by Mn oxides have been focused on activity; however, the identification of the best performing active site and corresponding catalytic cycles is also of critical importance. Herein, the real intrinsic activity of layered Mn oxide toward OER in Fe/Ni-free KOH is studied for the first time. At pH ≈ 14, the onset of OER for layered Mn oxide in the presence of Fe/Ni-free KOH happens at 1.72 V (vs reversible hydrogen electrode (RHE)). In the presence of Fe ions, a 190 mV decrease in the overpotential of OER was recorded for layered Mn oxide as well as a significant decrease (from 172.8 to 49 mV/decade) in the Tafel slope. Furthermore, we find that both Ni and Fe ions increase OER remarkably in the presence of layered Mn oxide, but that pure layered Mn oxide is not an efficient catalyst for OER without Ni and Fe under alkaline conditions. Thus, pure layered Mn oxide and electrolytes are critical factors in finding the real intrinsic activity of layered Mn oxide for OER. Our results call into question the high efficiency of layered Mn oxides toward OER under alkaline conditions and also elucidate the significant role of Ni and Fe impurities in the electrolyte in the presence of layered Mn oxide toward OER under alkaline conditions. Overall, a computational model supports the conclusions from the experimental structural and electrochemical characterizations. In particular, substitutional doping with Fe decreases the thermodynamic OER overpotential up to 310 mV. Besides, the thermodynamic OER onset potential calculated for the Fe-free structures is higher than 1.7 V (vs RHE) and, thus, not in the stability range of Mn oxides.

Highly active and stable surface structure for oxygen evolution reaction originating from balanced dissolution and strong connectivity in BaIrO3 solid solutions

Catalysts for the oxygen evolution reaction (OER) are receiving great interest since OER remains the bottleneck of water electrolyzers for hydrogen production. Especially, OER in acidic solutions is crucial since it produces high current densities and avoids precipitation of carbonates. However, even the acid stable iridates undergo severe dissolution during the OER. BaIrO₃ has the strongest IrO₆ connectivity and stable surface structure, yet it suffers from lattice collapse after OER cycling, making it difficult to improve the OER durability. In the present study, we have successfully developed an OER catalyst with both high intrinsic activity and stability under acidic conditions by preventing the lattice collapse after repeated OER cycling. Specifically, we find that the substitution of Ir-site with Mn for BaIrO₃ in combination with OER cycling leads to a remarkable activity enhancement by a factor of 28 and an overall improvement in stability. This dual enhancement of OER performance was accomplished by the novel strategy of slightly increasing the Ir-dissolution and balancing the elemental dissolution in BaIr_1−xMn_xO₃ to reconstruct a rigid surface with BaIrO₃-type structure. More importantly, the mass activity for BaIr_0.8Mn_0.2O₃ reached ∼73 times of that for IrO₂, making it a sustainable and promising OER catalyst for energy conversion technologies.

We have prevented lattice collapse and developed an OER catalyst with both high activity and stability by slightly increasing Ir-dissolution and balancing the elemental dissolution in BaIr_1−xMn_xO₃ for reconstructing the rigid catalytic surface.

Mesoporous Mn-Fe oxyhydroxides for oxygen evolution

Development of high-performance and earth-abundant catalysts is imperative for the oxygen evolution reaction (OER), and mesoporous oxyhydroxides show huge potential as advanced catalysts toward OER due to large specific surface...

Advanced Zinc-Air Batteries with Free-Standing Hierarchical Nanostructures of the Air Cathode for Portable Applications

It is today advanced that the development of a free-standing (binderless) air cathode via direct growth of nonprecious metal electrocatalysts onto the surface of the conductive collector would be a cutting-edge strategy to reduce the interfacial resistance, improve the mechanical stability, and reduce the final weight and the cost of manufacturing. Here, for Zn-air batteries (ZABs), we propose an innovative binderless noble-metal-free hierarchical nanostructured bifunctional air cathode in which high-density MnO_x nanorods (NRs) are directly grown on carbon nanotubes (CNTs) themselves synthesized on a microfibrous carbon paper (CP) substrate. All carbon/MnO_x air cathodes achieved specific capacities very close to the theoretical value of 820 mAh g_Zn^-1. A very stable voltage gap between the charge and discharge processes along hundred cycles was obtained, demonstrating the stability and good bifunctional electrocatalytic activities of these cathodes toward the oxygen reduction reaction/oxygen evolution reaction in a real ZAB device. As a proof-of-concept for handheld electronic applications, a ZAB assembled with CP/MnO_x NRs as the air electrode and a Zn plate anode operated a timer for 14 days successfully, whereas two ZAB-based CNTs/MnO_x cathodes connected in series powered a 2 V light-emitting diode (LED) bulb and a 3 V multimeter. The proposed strategy and results may pave the way for the rational design of hierarchical free-standing bifunctional electrocatalysts for ZABs, other metal-air batteries, and fuel cells.

Hierarchical Fe-Mn binary metal oxide core-shell nano-polyhedron as a bifunctional electrocatalyst for efficient water splitting

Electrochemical water splitting is convinced as one of the most promising solutions to combat the energy crisis. The exploitation of efficient hydrogen and oxygen evolution reaction (HER/OER) bifunctional electrocatalysts is undoubtedly a vital spark yet challenging for imperative green sustainable energy. Herein, through introducing a simple pH regulated redox reaction into a tractable hydrothermal procedure, a hierarchical Fe₃O₄@MnO_x binary metal oxide core-shell nano-polyhedron was designed by evolving MnO_x wrapped Fe₃O₄. The MnO_x effectively prevents the agglomeration and surface oxidation of Fe₃O₄ nano-particles and increases the electrochemically active sites. Benefiting from the generous active sites and synergistic effects of Fe₃O₄ and MnO_x, the Fe₃O₄@MnO_x-NF nanocomposite implements efficient HER/OER bifunctional electrocatalytic performance and overall water splitting. As a result, hierarchical Fe₃O₄@MnO_x only requires a low HER/OER overpotential of 242/188 mV to deliver 10 mA cm^-2, a small Tafel slope of 116.4/77.6 mV dec^-1, combining a long-term cyclability of 5 h. Impressively, by applying Fe₃O₄@MnO_x as an independent cathode and anode, the overall water splitting cell supplies a competitive voltage of 1.64 V to achieve 10 mA cm^-2 and super long cyclability of 80 h. These results reveal that this material is a promising candidate for practical water electrolysis application.

Structural Transformation of Heterogeneous Materials for Electrocatalytic Oxygen Evolution Reaction

Electrochemical water splitting for hydrogen generation is a promising pathway for renewable energy conversion and storage. One of the most important issues for efficient water splitting is to develop cost-effective and highly efficient electrocatalysts to drive sluggish oxygen-evolution reaction (OER) at the anode side. Notably, structural transformation such as surface oxidation of metals or metal nonoxide compounds and surface amorphization of some metal oxides during OER have attracted growing attention in recent years. The investigation of structural transformation in OER will contribute to the in-depth understanding of accurate catalytic mechanisms and will finally benefit the rational design of catalytic materials with high activity. In this Review, we provide an overview of heterogeneous materials with obvious structural transformation during OER electrocatalysis. To gain insight into the essence of structural transformation, we summarize the driving forces and critical factors that affect the transformation process. In addition, advanced techniques that are used to probe chemical states and atomic structures of transformed surfaces are also introduced. We then discuss the structure of active species and the relationship between catalytic performance and structural properties of transformed materials. Finally, the challenges and prospects of heterogeneous OER electrocatalysis are presented.

MnO2 Electrocatalysts Coordinating Alcohol Oxidation for Ultra-Durable Hydrogen and Chemical Productions in Acidic Solutions

Electrocatalytic hydrogen production under acidic conditions is of great importance for industrialization in comparison to that in alkaline media, which, unfortunately, still remains challenging due to the lack of earth-abundant, cost-effective and highly active anodic electrocatalysts that can be used durably under strongly acidic conditions. Here we report an unexpected finding that manganese oxide, a kind of common non-noble catalysts easily soluble in acidic solutions, can be applied as a highly efficient and extremely durable anodic electrocatalyst for hydrogen production from an acidic aqueous solution of alcohols. Particularly in a glycerol solution, a potential of as low as 1.36 V (vs. RHE) is needed at 10 mA cm^-2 , which is 270 mV lower than that of oxygen evolution reaction (OER), to oxidize glycerol into value-added chemicals such as formic acid, without oxygen production. To our surprise, the manganese oxide exhibits extremely high stability for electrocatalytic hydrogen production in coupling with glycerol oxidation for longer than 865 hours compared to shorter than 10 h for OER. Moreover, the effect of the addition of glycerol on the electrochemical durability has been probed via in situ Raman spectroscopic analysis and density functional theory (DFT) calculations. This work demonstrates that acid-unstable metal oxide electrocatalysts can be used robustly in acidic media under the presence of certain substances for electrochemical purposes, such as hydrogen production.

Progress of Nonprecious-Metal-Based Electrocatalysts for Oxygen Evolution in Acidic Media

Water oxidation, or the oxygen evolution reaction (OER), which combines two oxygen atoms from two water molecules and releases one oxygen molecule, plays the key role by providing protons and electrons needed for the hydrogen generation, electrochemical carbon dioxide reduction, and nitrogen fixation. The multielectron transfer OER process involves multiple reaction intermediates, and a high overpotential is needed to overcome the sluggish kinetics. Among the different water splitting devices, proton exchange membrane (PEM) water electrolyzer offers greater advantages. However, current anode OER electrocatalysts in PEM electrolyzers are limited to precious iridium and ruthenium oxides. Developing highly active, stable, and precious-metal-free electrocatalysts for water oxidation in acidic media is attractive for the large-scale application of PEM electrolyzers. In recent years, various types of precious-metal-free catalysts such as carbon-based materials, earth-abundant transition metal oxides, and multiple metal oxide mixtures have been investigated and some of them show promising activity and stability for acidic OER. In this review, the thermodynamics of water oxidation, Pourbaix diagram of metal elements in aqueous solution, and theoretical screening and prediction of precious-metal-free electrocatalysts for acidic OER are first elaborated. The catalytic performance, reaction kinetics, and mechanisms together with future research directions regarding acidic OER are summarized and discussed.