Redox mechanisms of conversion of Cr(VI) to Cr(III) by graphene oxide-polymer composite

Controllable integration of nano zero-valent iron into MOFs with different structures for the purification of hexavalent chromium-contaminated water: Combined insights of scavenging performance and potential mechanism investigations

This work combined the stability of the porous structure of metal-organic frameworks with the strong reducibility of nano zero-valent iron, for the controllable integration of NZVI into MOFs to utilize the advantages of each component with enhancing the rapid decontamination and scavenging of Cr(VI) from wastewater. Hence, four kinds of MOFs/NZVI composites namely ZIF67/NZVI, MOF74/NZVI, MIL101(Fe)/NZVI, CuBTC/NZVI, were prepared for Cr(VI) capture. The results indicated that the stable structure of ZIF67, MOF74, MIL101(Fe), CuBTC, was beneficial for the dispersion of NZVI that could help more close contact between MOFs/NZVI reactive sites and Cr(VI), subsequently, MOFs/NZVI was proved to be better scavengers for Cr(VI) scavenging than NZVI alone. The Cr(VI) capture achieved the maximum adsorption capacity at pH ~ 4.0, which might be due to the participation of more H+ in the reaction and better corrosion of NZVI at lower pH. Mechanism investigation demonstrated synergy of adsorption, reduction and surface precipitation resulted in enhanced Cr(VI) scavenging, and Fe(0), dissolved and surface-bound Fe(II) were the primary reducing species. The findings of this investigation indicated that the as-prepared composites of ZIF67/NZVI, MOF74/NZVI, MIL101(Fe)/NZVI, CuBTC/NZVI, with high oxidation resistance and excellent reactivity, could provide reference for the decontamination and purification of actual Cr(VI)-containing wastewater.

Biosorption of chromium by live and dead cells of Bacillus nitratireducens isolated from textile effluent

Bacillus nitratireducens was isolated from textile effluent and showed high tolerance to chromium (Cr), reaching up to a 1000 mg/L MIC value. This research was aimed at utilizing biosorbents from live and dead cells of B. nitratireducens to remove Cr from an aqueous solution. A batch biosorption test was performed, and mechanisms analysis was approached by an adsorption-desorption test, SEM-EDS, and FTIR analysis. Cr removal by dead cells in 25, 50, and 100 mg/L of Cr were 58.99 ± 0.7%, 69.8 ± 0.2%, and 82.87 ± 0.11%, respectively, while that by live cells was 73.08 ± 1.9%, 80.27 ± 6.33%, and 86.17 ± 1.93%, respectively. Live cells showed significantly higher Cr removal and adsorption capacities as compared to dead cells. In all concentrations, absorption contributed more than adsorption to the Cr removal by both live and dead cells. Absorption of Cr was subjected to occur due to passive mechanisms in dead cells while involving some active mechanisms in live cells. SEM-EDS confirmed the detection of Cr on the cell surface, while FTIR revealed the shifting of some peaks after the biosorption test, suggesting interactions between Cr and functional groups. Further TEM analysis is suggested to be conducted as a future approach to reveal the inner structure of cells and confirm the involvement of absorption mechanisms.

Removal of Cr(VI) from aqueous solution using ball mill modified biochar: multivariate modeling, optimization and experimental study

Chromium (Cr(VI)) pollution has attracted wide attention due to its high toxicity and carcinogenicity. Modified biochar has been widely used in the removal of Cr(VI) in water as an efficient and green adsorbent. However, the existing biochar prepared by chemical modification is usually complicated in process, high in cost, and has secondary pollution, which limits its application. It is urgent to explore modified biochar with simple process, low cost and environmental friendliness. Therefore, ball milling wheat straw biochar (BM-WB) was prepared by ball milling technology in this paper. The adsorption characteristics and mechanism of Cr(VI) removal by BM-WB were analyzed by functional group characterization, adsorption model and response surface method. The results showed that ball milling effectively reduced the particle size of biochar, increased the specific surface area, and more importantly, enhanced the content of oxygen-containing functional groups on the surface of biochar. After ball milling, the adsorption capacity of Cr(VI) increased by 3.5-9.1 times, and the adsorption capacity reached 52.21 mg/g. The adsorption behavior of Cr(VI) follows the pseudo-second-order kinetics and Langmuir isotherm adsorption model rate. Moreover, the Cr(VI) adsorption process of BM-WB is endothermic and spontaneous. Under the optimized conditions of pH 2, temperature 45 °C, and adsorbent dosage 0.1 g, the removal rate of Cr(VI) in the solution can reach 100%. The mechanism of Cr(VI) adsorption by BM-WB is mainly based on electrostatic attraction, redox and complexation. Therefore, ball milled biochar is a cheap, simple and efficient Cr(VI) removal material, which has a good application prospect in the field of remediation of Cr(VI) pollution in water.

Fruit waste-derived cellulose-polyaniline composite for adsorption-coupled reduction of chromium oxyanions

Hexavalent chromium oxyanions, known as potentially toxic micropollutants, exist in the effluents and discharges of metallurgical, electroplating, refractory, chemical, and tanning industries. The exposure of chromium-contaminated water causes severe health hazards. The present work outlines a facile approach to grow polyaniline (PANI) on fruit-waste-derived cellulose (CEL) via oxidative polymerization of aniline; followed by chemical processing with NH4OH to obtain CEL-PANI-EB composites for adsorptive separation-coupled reduction of highly toxic hexavalent chromium oxyanions. The spectroscopic analyses of the CEL-PANI-EB composite before and after adsorption of Cr(VI) oxyanions revealed hydrogen bonding, electrostatic, and complexation as major interactive pathways. The adsorbed hexavalent chromium oxyanions are reduced into Cr(III) species by oxidation of PANI-based benzenoid amine into quinoid imine in the CEL-PANI-EB composite. The adsorption of Cr(VI) oxyanions by the CEL-PANI-EB composite showed negligible effects of other anionic co-pollutants, like NO3- and SO42-. The CEL-PANI-EB composite adsorbed Cr(VI) oxyanions with a removal capacity of 469 mg g-1, based on the Langmuir adsorption isotherm model. The hydroxyl functionalities in cellulose and amine/imine functionalities in PANI facilitate the electrostatic attraction between the CEL-PANI-EB and Cr(VI) oxyanions in an acidic environment beside the hydrogen linkages. The adsorbed Cr(VI) oxyanions are reduced to Cr(III)-based species by the benzenoid amines of PANI, as revealed from the XPS analyses. The CEL-PANI-EB composite showed excellent recyclability and maintained 83.4% adsorption efficiency after seven runs of chromium adsorption-desorption. The current findings reveal the potential of CEL-PANI-EB composites for the adsorptive removal of Cr(VI) oxyanions and their conversion into a lesser toxic form, making them promising materials for wastewater treatment applications.

Robust Magnetic Proximity Induced Anomalous Hall Effect in a Room Temperature van der Waals Ferromagnetic Semiconductor Based 2D Heterostructure

Developing novel high-temperature van der Waals ferromagnetic semiconductor materials and investigating their interface coupling effects with 2D topological semimetals are pivotal for advancing next-generation spintronic and quantum devices. However, most van der Waals ferromagnetic semiconductors exhibit ferromagnetism only at low temperatures, limiting the proximity research on their interfaces with topological semimetals. Here, an intrinsic, van der Waals layered room-temperature ferromagnetic semiconductor crystal, FeCr0.5 Ga1.5 Se4 (FCGS), is reported with a Curie temperature (TC ) as high as 370 K, setting a new record for van der Waals ferromagnetic semiconductors. The saturation magnetization at low temperature (2 K) and room temperature (300 K) reaches 8.2 and 2.7 emu g-1 , respectively. Furthermore, FCGS possesses a bandgap of ≈1.2 eV, which is comparable to the widely used commercial silicon. The FCGS/graphene 2D heterostructure exhibits an impeccably smooth and gapless interface, thereby inducing a robust van der Waals magnetic proximity coupling effect between FCGS and graphene. After the proximity coupling, graphene undergoes a charge carrier transition from electrons to holes, accompanied by a transition from non-magnetic to ferromagnetic transport behavior with robust anomalous Hall effect (AHE). Notably, the van der Waals magnetic proximity-induced AHE remains robust even up to 400 K.

Synthesis and characterization of iron oxide-commercial activated carbon nanocomposite for removal of hexavalent chromium (Cr6+) ions and Mordant Violet 40 (MV40) dye

Iron Oxide-commercial activated carbon nanocomposite (CAC-IO) was prepared from commercial activated carbon (CAC) by the co-precipitation method, and the resulting nanocomposite was used as an adsorbent to remove hexavalent chromium (Cr6+) ions and Mordant Violet 40 (MV40) dye from wastewater. The produced materials (CAC, CAC after oxidation, and CAC-IO) were comparatively characterized using FTIR, BET, SEM, EDX TEM, VSM, and XRD techniques. The adsorption mechanism of Cr6+ ions and MV40 dye on CAC-IO was examined using Langmuir and Freundlich isotherm models.. Different models were applied to know the adsorption mechanism and it was obtained that Pseudo-second order fits the experimental data better. This means that the adsorption of the adsorbate on the nanocomposite was chemisorption. The maximum removal percent of Cr6+ ions by CAC-IO nanocomposite was 98.6% determined as 2 g L-1 adsorbent concentration, 100 mg L-1 initial pollutant concentration, solution pH = 1.6, the contact time was 3 h and the temperature was room temperature. The maximum removal percentage of Mordant Violet 40 dye (C.I. 14,745) from its solutions by CAC-IO nanocomposite was 99.92% in 100 mg L-1 of initial dye concentrations, 1.0 g L-1 of adsorbent concentration, solution pH = 2.07, the contact time was 3 h. The MV40 dye adsorption on CAC-IO was the most fitted to the Freundlich isotherm model. The maximum adsorption capacity was calculated according to the Langmuir model as 833.3 mg g-1 at 2 g L-1 of adsorbent concentration and 400 mg L-1 of initial MV40 dye concentration. The Cr6+ ions adsorption on CAC-IO was more fitted to the Freundlich model with Qmax, equal to 312.50 mg g-1 at 1 g L-1 adsorbent concentration and 400 mg L-1 of Cr6+ ions initial concentrations.

Synthesis of High-Entropy Alloys with a Tailored Composition and Phase Structure Using a Single Configurable Target

Previously, refractory high-entropy alloys (HEAs) with high crystallinity were synthesized using a configurable target without heat treatment. This study builds upon prior investigations to develop nonrefractory elemental HEAs with low crystallinity using a novel target system. Different targets with various elemental compositions, i.e., Co20Cr20Ni20Mn20Mo20 (target 1), Co30Cr15Ni25Mn15Mo15 (target 2), and Co15Cr25Cu20Mn20Ni20 (target 3), are designed to modify the phase structure. The elemental composition is varied to ensure face-centered cubic (FCC) or body-centered cubic (BCC) phase stabilization. In target 1, the FCC and BCC phases coexist, whereas targets 2 and 3 are characterized by a single FCC phase. Thin films based on targets 1 and 2 exhibit crystalline phases followed by annealing, as indicated by X-ray diffraction (XRD) and transmission electron microscopy (TEM) analyses. In contrast, target 3 yields crystalline thin films without any heat treatment. The thin-film coatings are classified based on the atomic size difference (δ). The δ value for the target with the elemental composition CoCrMoMnNi is 9.7, i.e., ≥6.6, corresponding to an HEA with an amorphous phase. However, the annealed thin film is considered a multiprincipal elemental alloy. In contrast, δ for the CoCrCuMnNi HEA is 5, i.e., ≤6.6, upon the substitution of Mo with Cu, and a solid solution phase is formed without any heat treatment. Thus, the degree of crystallinity can be controlled through heat treatment and the manipulation of δ in the absence of heat treatment. The XRD results clarify the crystallinity and phase structure, indicating the presence of FCC or a combination of FCC and BCC phases. The outcomes are consistent with those obtained through the analysis of the valence electron concentration based on X-ray photoelectron spectroscopy. Furthermore, a selected area electron diffraction analysis confirms the presence of both amorphous and crystalline structures in the HEA thin films. Additionally, phase evolution and segregation are observed at 500 °C.

Capturing Acidic CO2 Using Surface-Active Difunctional Core-Shell Composite Polymer Particles via an Aqueous Medium

Multifunctional surface-active polymeric composites are attractive materials for the adsorption of various small molecules. Herein, dual-functionalized micron-sized surface-active composite polymer particles were prepared by a three-step process for CO2 adsorption. First, polystyrene (PS) seed particles were prepared via the dispersion polymerization of styrene. PS/P(MMA-AAm-EGDMA) composite polymer particles were then synthesized by aqueous seeded copolymerization of methyl methacrylate (MMA) and acrylamide (AAm) in the presence of an ethylene glycol dimethacrylate (EGDMA) cross-linker. Finally, the amide moieties of PS/P(MMA-AAm-EGDMA) composite particles were converted into an amine-functionalized composite by using the Hofmann degradation reaction. The presence of primary amine groups on the surface of aminated composite particles was confirmed by some conventional chemical routes, such as diazotization and Schiff's base formation reactions. The formation and functionality of the PS seed, PS/P(MMA-AAm-EGDMA), and aminated PS/P(MMA-AAm-EGDMA) composite polymer particles were confirmed by Fourier transform infrared (FTIR) spectra analyses. Scanning electron microscopy (SEM) analysis revealed spherical shape, size, and surface morphologies of the PS seed, reference composite, and aminated composites. The elemental surface compositions, surface porosity, pore volume, pore diameter, and surface area of both composite particles were evaluated by energy-dispersive X-ray (EDX) mapping, X-ray photoelectron spectroscopy, and Brunauer-Emmett-Teller (BET) and Barrett-Joyner-Halenda (BJH) analyses. Dynamic light scattering (DLS) and ζ-potential measurements confirmed the pH-dependent surface properties of the functionalized particles. The amount of the adsorbed anionic emulsifier, sodium dodecyl sulfate (SDS), on the surface of aminated PS/P(MMA-AAm-EGDMA) is higher at pH 4 than that at pH 10. A vice versa result was found in the case of cationic surfactant, hexadecyltrimethylammonium bromide (HTABr), adsorption. Synthesized aminated composite particles were used as an adsorbent for CO2 adsorption via bubbling CO2 in an aqueous medium. The changes in dispersion pH were monitored continuously during the adsorption of CO2 under various conditions. The amount of CO2 adsorption by aminated composite particles was found to be 209 mg/g, which is almost double that of reference composite particles.

Accumulation mechanisms for contaminants on weak-base hybrid ion exchange resins

Mechanism of hexavalent chromium removal (Cr(VI) as CrO42-) by the weak-base ion exchange (IX) resin ResinTech® SIR-700-HP (SIR-700) from simulated groundwater is assessed in the presence of radioactive contaminants iodine-129 (as IO3-), uranium (U as uranyl UO22+), and technetium-99 (as TcO4-), and common environmental anions sulfate (SO42-) and chloride (Cl-). Batch tests using the acid sulfate form of SIR-700 demonstrated Cr(VI) and U(VI) removal exceeded 97%, except in the presence of high SO42- concentrations (536 mg/L) where Cr(VI) and U(VI) removal decreased to ≥ 80%. However, Cr(VI) removal notably improved with co-mingled U(VI) that complexes with SO42- at the protonated amine sites. These U-SO42- complexes are integral to U(VI) removal, as confirmed by the decrease in U(VI) removal (<40%) when the acid chloride form of SIR-700 was used instead. Solid phase characterization revealed that CrO42- is removed by IX with SO42- complexes and/or reduced to amorphous Cr(III)(OH)3 at secondary alcohol sites. Tc(VII)O4- and I(V)O3- also undergo chemical reduction, following a similar removal mechanism. Oxyanion removal preference is determined by the anion reduction potential (CrO42->TcO4->IO3-), geometry, and charge density. For these reasons, 39% and 69% of TcO4- and 17% and 39% of IO3- are removed in the presence and absence of Cr(VI), respectively.

Synthesis of co-pyrolyzed biochar using red mud and peanut shell for removing phosphate from pickling wastewater: Performance and mechanism

Iron (Fe)/iron oxide-modified biochar has practicable adsorption capability for phosphorus (P), but it is expensive. In this study, we synthesized novel low-cost and eco-friendly adsorbents co-pyrolyzed biochars using Fe-rich red mud (RM) and peanut shell (PS) wastes via a one-step pyrolysis process for removing P from pickling wastewater. The preparation conditions (heating rate, pyrolysis temperature, and feedstock ratio) and P adsorption behaviors were systematically investigated. In addition, a series of characterization and approximate site energy distribution (ASED) analyses were conducted to understand the P adsorption mechanisms. The magnetic biochar (BR7P3) with m (RM):m (PS) of 7:3 prepared at 900°C and 10 °C/min had a high surface area (164.43 m2/g) and different abundant ions (including Fe3+, and Al3+). In addition, BR7P3 exhibited the best P removal capability (142.6 mg/g). The Fe2O3 from RM was successfully reduced to Fe0, which was easily oxidized as Fe3+ to precipitate with H2PO4-. The electrostatic effect, Fe-O-P bonding, and surface precipitation were the main mechanisms of P removal. ASED analyses revealed that high distribution frequency and solution temperature led to a high P adsorption rate of the adsorbent. Therefore, this study provides new insight into the waste-to-wealth strategy by transforming PS and RM into mineral-biomass biochar with excellent P adsorption capability and environmental adaptability.

Formation of self-nitrogen-doping activated carbon from Fish/sawdust/ZnCl2 by hydrothermal and pyrolysis for toxic chromium adsorption from wastewater

This study gives a description of the formation of self-nitrogen doped activated carbon (NDAC) by a novel way of employing fish meal (mixture of Atherina hepseetus and Sardina pilchardus of 60% protein) as nitrogen dopant, ZnCl₂ as impregnate agent, sawdust as carbon source and water with a mass ratio (2:1:1:12), which subjected to the hydrothermal process. The hydrothermal mixture was oven dried and carbonized under a flow of nitrogen for one h at 600, 700, and 800 °C. The characterization of NDAC was performed by using various analytical techniques analyses. The synthesized NDAC exhibited unique features such as microporous structure (1.84 ~ 2.01 nm), high surface area (437.51 ~ 680.86 m²/g), the volume of total pores (0.22 ~ 0.32 cm³/g) and nitrogen content (12.82 ~ 13.73%). Batch removal tests were achieved to investigate the impact of chromium ions starting concentration (100-400 mg/L), NDAC dose (0.5-2.5 g/L), pH and contact time (5-120 min). Such helpful characteristics of NDAC, particularly for NDAC600, were suitable to use as an excellent adsorbent for Cr⁶⁺ ions with a maximum adsorption capacity (Q_m) (769.23 mg/g), and the highest chromium ions adsorption uptake (81.18%) was obtained at pH value 1.5 at room temperature. Both Halsey and Temkin models fitted the adsorption data quite reasonably. The uptake of toxic chromium ions is best represented with pseudo-second-order rate kinetics data.

Water Decontamination from Cr(VI) by Transparent Silica Xerogel Monolith

Cr(VI) is highly soluble and mobile in water solution and extremely toxic. In order to obtain a specific material with adsorption properties towards Cr(VI), and that can be used in environmental remediation of water contaminated with Cr(VI), one-step sol-gel technique, at low temperature (50 °C), has been optimized to prepare transparent silica-based xerogel monolith by using tetraethyl orthosilicate as precursor. The obtained xerogel, with disk shape, was fully characterized by Raman, BET, FE-SEM and XRD analysis. The results indicated that the material showed silica amorphous phase and high porosity. The study of the adsorption properties towards different concentrations of Cr(VI), in the form of HCrO₄^- in acidic condition, showed prominent results. The absorption kinetics were evaluated by studying different models, the final result showing that the absorption of Cr(VI) occurred through intra-particle diffusion process, following two steps, and that the absorption equilibrium is regulated by Freundlich isotherm model. The material can be restored by reducing the hazardous Cr(VI) to Cr(III), a less toxic form of chromium, by 1,5-diphenylcarbazide, and with successive treatment in acidic water.

Speciation of Hexavalent Chromium in Aqueous Solutions Using a Magnetic Silica-Coated Amino-Modified Glycidyl Methacrylate Polymer Nanocomposite

A new magnetic amino-functionalized polymeric sorbent based on glycidyl methacrylate was synthesized and used in the separation of chromium Cr(VI) oxyanions sorption from aqueous solutions in a static batch system. The kinetic and isothermal parameters of the sorption process were determined. The experimental data were best fitted by a pseudo-second-order model with R² = 0.994 and χ² = 0.004. The sorption process of Cr(VI) removal by amino-functionalized sorbent was controlled by both intraparticle diffusion and liquid film diffusion. The equilibrium results showed that the sorption process is best described by the Freundlich model, followed closely by the Sips isotherm model, with a maximum sorption capacity of 64 mg/g. Quantum chemical modeling revealed that the sorption sites on the sorbent surface are fragments with diethylenetriamine and aminopropyl silane groups that coated the magnetic nanoparticles. The calculations showed that Cr(VI) oxyanions (Cr₂O₇^2-, CrO₄^2- and HCrO₄^-) bind to both sorption sites, with diethylenetriamine centers slightly favored. The X-ray photoelectron spectroscopy (XPS) spectra demonstrate that the chromium bound to the sorbent in the form of Cr(III), indicating that the Cr(VI) can be converted on the surface of the sorbent to a less harmful form Cr(III) due to the sorbent's chemical composition.

pH-Triggered Recovery of Organic Polymer Photocatalytic Particles for the Production of High Value Compounds and Enhanced Recyclability

Pseudo-homogeneous polymeric photocatalysts are an emerging class of highly efficient and tunable photocatalytic materials, where the photocatalytic centers are easily accessible. The creation of highly efficient photocatalytic materials that can be rapidly separated and recovered is one of the critical challenges in photocatalytic chemistry. Here, we describe pH-responsive photocatalytic nanoparticles that are active and well-dispersed under acidic conditions but aggregate instantly upon elevation of pH, enabling easy recovery. These responsive photocatalytic polymers can be used in various photocatalytic transformations, including Cr^VI reduction and photoredox alkylation of indole derivative. Notably, the cationic nature of the photocatalyst accelerates reaction rate of an anionic substrate compared to uncharged species. These photocatalytic particles could be readily recycled allowing multiple successive photocatalytic reactions with no clear loss in activity.

N,Zn-Doped Fluorescent Sensor Based on Carbon Dots for the Subnanomolar Detection of Soluble Cr(VI) Ions

The development of a fluorescent sensor has attracted much attention for the detection of various toxic pollutants in the environment. In this work, fluorescent carbon dots (N,Zn-CDs) doped with nitrogen and zinc were synthesized using citric acid monohydrate and 4-pyridinecarboxyaldehyde as carbon and nitrogen sources, respectively. The synthesized N,Zn-CDs served as an "off" fluorescence detector for the rapid and sensitive detection of hexavalent chromium ions (Cr(VI)). The zinc metal integrated into the heteroatomic fluorescent carbon dot played a functional role by creating a coordination site for the hydrogen ions that were displaced after the addition of Cr to the solution matrix. The stepwise addition of Cr(VI) effectively quenched the fluorescence intensity of the N,Zn-CDs, and this phenomenon was attributed to the internal filter effect. A low detection limit of 0.47 nmol/L for Cr(VI) was achieved in the fluorescence experiments. Real water samples were used to evaluate the practical application of N,Zn-CDs for the quantification of Cr(VI). The results show acceptable recoveries and agreement with ion chromatography-ultraviolet spectrometry results. These good recoveries indicate that the fluorescence probe is very well suited for environmental measurements.

Conversion of novel tannery sludge-derived biochar/TiO2 nanocomposite for efficient removal of Cr (VI) under UV light: photocatalytic performance and mechanism insight

An investigation on the reduction of Cr (VI) pollutant from tannery effluents using TiO₂, SB/TiO₂, and c-SB/TiO₂ nano photocatalysts was presented in this study. For the preparation of Biochar-based TiO₂ photocatalyst (SB/TiO₂), tannery sludge was utilized as a precursor. Hydrothermal pre-treatment was adopted to prepare chemically activated SB/TiO₂ and SB/TiO₂ nanocomposites. The morphology, crystal structure, optical properties, and elemental composition of the prepared catalysts were analyzed by XRD, FT-IR, SEM-EDX, BET analysis, ZPC, PL, TGA, and Raman spectroscopy. The band gap analysis of Photocatalyst was measured using a DRS instrument, and band gap energy of 3.39 eV was obtained for c-SB/TiO₂ photocatalyst. The developed c-SB/TiO₂ catalyst exhibits a larger specific surface area of 646.85 m²/g than TiO₂ and SB/TiO₂ (74.58 m²/g and 573.74 m²/g), respectively. The enhanced photocatalytic activity for the pollutant removal was achieved by the photocatalyst due to their wide band gap and effective charge separation. The kinetic rate constant was achieved in the pseudo-first-order model, which fits well for the reduction of Cr (VI). Furthermore, at the optimal conditions of 10 mg/L contaminant concentration, pH 2, and 0.5 g/L catalyst dosage, 98.56% reduction was observed after 180 min of reaction. The OH acts as a major removal pathway for Cr (VI) contaminants with more than 50% reduction in COD. This study proves that c-SB/TiO₂ photocatalysts can remove toxic contaminants under UV light irradiation with good recycling performance up to 5 times.

Synthesis of graphene oxide-modified porous chitosan cross-linked polyaniline composite for static and dynamic removal of Cr(VI)

A novel ternary composite was synthesized comprising graphene oxide-modified porous chitosan cross-linked polyaniline (GO@CS-PANI) by improved Hummers method, followed by cross-linking and grafting. The morphological, structural, and electrical properties of the composite were characterized by FESEM, BET, XRD, RAMAN, FTIR spectra, and zeta potential. It was found that the composite shows excellent Cr(VI) removal performance both in static and dynamic adsorption. The optimal adsorption parameters were solution at pH of 2.0, adsorbent dosage of 0.4 g/L, time of 45 min, and temperature of 35 °C. The Langmuir isotherm model was the best-fitted model, indicating homogeneous adsorption with maximum uptake of 539.83 mg/g. Pseudo-second-order was the best-fitted kinetic model, and the rate was controlled by film diffusion. Thermodynamic data demonstrated that the process was spontaneous, endothermic, and feasible. From the dynamic study, it was witnessed that a lower flow rate and a higher bed height were suitable for maximum adsorption performance. The Thomas model was the best-fitted model for data obtained from the dynamic study. Competition from interfering ions showed that anions have little effect on Cr(VI) removal, whereas cations have no such effect. The adsorption mechanism involved electrostatic attraction, π-π interaction, ion exchange, and metal ion complexion. After five cycles of adsorption-desorption study, the composite still removed 76% Cr(VI). These findings of the present study and the reusable nature of GO@CS-PANI composite signify the innovative and excellent adsorbent for wastewater treatment.

Ferrous Industrial Wastes-Valuable Resources for Water and Wastewater Decontamination

Ferrous waste by-products from the metallurgical industry have a high potential for valorization in the context of the circular economy, and can be converted to value-added products used in environmental remediation. This research reviews the latest data available in the literature with a focus on: (i) sources from which these types of iron-based wastes originate; (ii) the types of ferrous compounds that result from different industries; (iii) the different methods (with respect to the circular economy) used to convert them into products applied in water and wastewater decontamination; (iv) the harmful effects ferrous wastes can have on the environment and human health; and (v) the future perspectives for these types of waste.

Visible-light responsive ZnSe-anchored mesoporous TiO2heterostructures for boosted photocatalytic reduction of Cr(VI)

The accumulation of Cr(VI) ions in water can cause serious influences on the environment and human health. This work reports a humble synthesis of ZnSe nanoparticles anchored to the sol-gel prepared TiO₂for visible-light-driven photocatalytic reduction of Cr(VI) ions. The 7.9 nm ZnSe nanoparticles were attached to TiO₂surfaces at a content of 1.0-4.0 wt% as experiential by TEM investigation. The designed nanocomposite unveiled mesostructured surfaces exhibiting surface areas of 176-210 m²g^-1. The impregnation of ZnSe amended the visible-light absorption of TiO₂due to the bandgap decrease from 3.14 to 2.90 eV. The photocatalytic reduction of Cr(VI) applying the optimized portion of 3.0 wt% ZnSe/TiO₂was achieved at 177μmol min^-1. This photocatalytic activity is higher than the common Degussa P25 and pristine TiO₂by 20 and 30 times, respectively. The improved performance is signified by the efficient interfacial separation of charge carriers by the introduction of ZnSe. This innovative ZnSe/TiO₂has also shown photocatalytic stability for five consecutive runs.

Functionalizing biochar by Co-pyrolysis shaddock peel with red mud for removing acid orange 7 from water

Biochar modification by metal/metal oxide is promising for improving its adsorption capability for contaminants, especially the anions. However, conventional chemical modifications are complicated and costly. In this study, novel Fe/Fe oxide loaded biochars (RMBCs) were synthesized from a one-step co-pyrolysis of red mud (RM) and shaddock peel (SP), and their potential application for removing anionic azo dye (acid orange 7, AO7) from the aqueous environment was evaluated. Fe from red mud was successfully loaded onto biochars pyrolyzed at 300-800 °C, which presented from oxidation form (Fe₂O₃) to the reduction forms (FeO and Fe⁰) with increasing pyrolysis temperature. The RMBC produced at 800 °C with RM:SP mass ratio of 1:1 (RMBC800_1:1) exhibited the best capability for AO7 removal (∼32 mg/g), attributed to both adsorption and degradation. The higher surface area of RMBC800_1:1 and its greater affinity for AO7 led to the higher adsorption. In addition, RMBC800_1:1-induced degradation of AO7 was another key mechanism for AO7 removal. The reduction forms of Fe (FeO or Fe⁰) in RMBC800_1:1 may provide electrons for breaking down the azo bond in AO7 molecules and result in degradation, which is further enhanced in acid conditions due to the participation of readily release of Fe²⁺ and the available H⁺ in AO7 degradation. Furthermore, RMBC800_1:1 can be easily separated from the treated water by using magnetic field, which significantly benefits its separation in wastewater treatment.

Novel reusable amine-functionalized cellulose acetate beads impregnated aminated graphene oxide for adsorptive removal of hexavalent chromium ions

In this study, a multi-featured adsorbent was developed for the adsorptive removal of hexavalent chromium (Cr⁶⁺) ions. Herein, aminated graphene oxide (GO-NH₂) was firstly synthetized and incorporated into cellulose acetate beads (CA) which were followed by surface amine-functionalization process. Varies characterization tools such as FT-IR spectroscopy, SEM, TGA, XRD, BET, XPS and zeta potential were employed to ensure the successful fabrication of GO-NH₂@CA-NH₂ composite beads. An enhancement in the adsorption performance was attained, while the adsorption equilibrium was closely gotten within only 60 min. Therefore, the adsorption capacity was boosted with increasing GO-NH₂ ratio in the beads matrix from 10 to 25%. Furthermore, the adsorption process agreed with Freundlich isotherm model with a supreme adsorption capacity of 410.21 mg/g at pH 2, while data followed the pseudo-second-order kinetic model. Besides, thermodynamic studies denoted that the adsorption process was endothermic, randomness and spontaneous. The composite beads retained better adsorption characteristics for seven sequential cycles with ease of separation. The proposed adsorption of Cr⁶⁺ onto GO-NH₂@CA-NH₂ surface occurred via the electrostatic interactions, reduction process and coordinate-covalent bonds. These findings hypothesize that the fabricated GO-NH₂@CA-NH₂ beads could be act as easy-separable and reusable adsorbent for efficient adsorption of Cr⁶⁺ ions.

Highly efficient Cr(VI) remediation by cationic functionalized nanocellulose beads

Applications of nanocellulose as a water treatment material are being actively pursued based on its interesting properties, such as renewability, large specific surface area, hydrophilic surface chemistry, and biodegradability. This study used carboxymethyl cellulose nanofibrils (CMCNFs) to prepare a typical bead-type adsorbent with improved structural stability as an actual water treatment restoration material. In addition, a cationized nanocellulose adsorbent was prepared by introducing polyethyleneimine (PEI) on the surface of the CMCNF (P/CMCNF), the removal efficiency of Cr(VI) was evaluated, and its mechanism was elucidated. As a result, the P/CMCNF beads showed an excellent Cr(VI) removal capacity of 1302.3 mg/g, the best result among cellulose-based adsorption materials. Cr(VI) was effectively removed by electrostatic attractions combined with chemical reduction and chelation mechanisms. Furthermore, the macrobead fabrication and PEI surface modification process improved the underwater stability of the P/CMCNF, and it showed excellent reuse efficiency.

Immobilization of W(VI) and/or Cr(VI) in soil treated with montmorillonite modified by a gemini surfactant and tetrachloroferrate (FeCl4-)

The coexistence of highly toxic chromium (Cr) and the emerging contaminant tungsten (W) in the soil adjacent to W mining areas is identified. Immobilization of W and/or Cr is vital for the safe utilization of contaminated soil. In this study, the cationic gemini surfactant (butane-1,4-bis(dodecyl dimethyl ammonium bromide)) and tetrachloroferrate (FeCl₄^-)-modified montmorillonite (FeOMt) was applied to investigate the retention performance of W and/or Cr in the soil. Regardless of the initially spiked amount of WO₄^2- and/or CrO₄^2-, the W and/or Cr leached in soil solution was rapidly immobilized within 5 min. The immobilization rates of W and/or Cr in the single and binary soil systems were stably maintained against the variations in pH and coexisting anion. FeOMt showed more favorable performance in the retention of W and/or Cr with respect to the precursors (i.e., the original Mt and surfactant-modified Mt) and efficiently inhibited the phytotoxicity and bioaccumulation of W and/or Cr in mung beans. Due to the ion exchange, complexation, reduction, and flocculation, the addition of FeOMt transformed W and/or Cr from exchangeable/carbonate species to reducible/oxidizable fractions, reducing the environmental risk. FeCl₄^- complex, as a byproduct of the steel pickling process in industry, plays the pivotal role in the efficient retention of W and Cr. Based on the facile synthesis procedure and the efficient performance, the use of FeOMt for the amendment of W- and/or Cr-contaminated soil is feasible and promising.

Cationic surface-modified regenerated nanocellulose hydrogel for efficient Cr(VI) remediation

Because nanocellulose has a large specific surface area and abundant hydroxyl functional groups due to its unique nanomorphology, interest increases as an eco-friendly water treatment material. However, the distinctive properties of nanocellulose, which exists in a dispersion state, strongly hamper its usage in practical water treatment processes. Additionally, nanocellulose shows low performance in removing anionic pollutants because of its anionic characteristics. In an effort to address this challenge, regenerated cellulose (RC) hydrogel was fabricated through cellulose's dissolution and regeneration process using an eco-friendly aqueous solvent system. Subsequently, a crosslinking process was carried out to introduce the cationic functional groups to the RC surface PEI coating (P/RC). As a result, the PEI surface cationization process improved the mechanical rigidity of RC and showed an excellent Cr(VI) removal capacity of 578 mg/g. In addition, the prepared P/RC maintained more than 90% removal efficiency even after seven reuses.

Mechanistic insights of hexavalent chromium remediation by halloysite-supported copper nanoclusters

Chromium (Cr) pollution is a significant environmental concern with remediation challenge. Hexavalent chromium (Cr(VI)) is more toxic than trivalent chromium (Cr(III)) due to its mutagenicity and oncogenicity. In this investigation, a multi-functional material, copper nanoclusters (CuNCs)-halloysite nanotubes (HNT) composite (CuNCs@HNT), has been synthesised in an eco-friendly manner and utilised for Cr(VI) remediation. Advanced analytical tools confirmed the seeding of ultra-fine CuNCs onto HNT surfaces. The maximum adsorption capacity of CuNCs@HNT is 79.14 ± 6.99 mg/g at pH 5 ± 0.1 with an increment at lower pHs. This performance was comparable for real surface stream water as well as other reported materials. The pseudo-second-order kinetic-, intra-particle diffusion- and Freundlich isotherm models well fit the experimental data implying that the chemisorption, multiphase diffusion and multi-molecular layer distribution occurred during adsorption. The Fourier-transform infrared and the x-ray photoelectron spectra also ensured the transformation of Cr(VI) to Cr(III) indicating the material's suitability for concurrent adsorption and reduction of Cr(VI). While coexisting cations and anions did not overwhelm this adsorption, CuNCs@HNT was regenerated and reused five successive times in adsorption-desorption cycles without significant loss of adsorption capacity and material's integrity. Therefore, this multi-functional, biocompatible, low-cost and stable CuNCs@HNT composite may have practical application for similar toxic metals remediation.

Microwave Synthesis, Characterization and Perspectives of Wood Pencil-Derived Carbon

More than 14 billion pencils are manufactured and used globally every year. On average, a pencil is discarded after 60% of its original length has been depleted. In the present work we propose a simple and affordable way of converting this non-neglectable amount of waste into added value carbon product. In particular, we demonstrate the microwave synthesis of carbon from the wood pencil with and without chemical activation. This could be a process stage before the final recycling of the expensive graphite core. In the latter case, irradiation of the wood pencil in a domestic microwave oven heats up the pencil’s graphite core, thus inducing carbonization of its wood casing. The carbonized product consists of amorphous carbon nanosheets having relatively low surface area. However, if the wood pencil is soaked in 50% KOH aqueous solution prior to microwave irradiation, a significantly higher surface area of carbon is obtained, consisting of irregular-shaped porous particles. Consequently, the obtained carbon can easily decolorize a methylene blue aqueous solution, can be used to make pocket warmers or gunpowder, and lastly, serves as an excellent adsorbent towards Cr(VI) removal from water, showing a maximum adsorption capacity of 70–75 mg/g within 24 h at 23 °C, pH = 3.

Enhanced Cr(vi) removal by hierarchical CoFe2O4@SiO2–NH2via reduction and adsorption processes

CoFe2O4@SiO2–NH2 shows excellent removal performance towards Cr(vi) due to its excellent electrostatic effect as well as the reduction process originating from the –CH group.

Pig lung fibrosis is active in the subacute CdCl2 exposure model and exerts cumulative toxicity through the M1/M2 imbalance

Environmental pollutant cadmium (Cd) can cause macrophage dysfunction, and the imbalance of M1/M2 is involved in the process of tissue fibrosis. In order to explore the effect of subacute CdCl₂ exposure on pig lung tissue fibers and its mechanism, based on the establishment of this model, ICP-MS, H&E staining, Masson staining, Immunofluorescence, RT-PCR, and Western Blot methods were used to detect related indicators. The results found that lung tissue fibrosis, Cd content significantly increased, lung tissue ion disturbance, miR-20a-3p down-regulation, M1/M2 imbalance, LXA4/FPR2 content decreased, MDA content increased, NF-κB/NLRP3, TGFβ pathway, PPARγ/Wnt pathway activated, and the expression of fibrosis-related factors increased. The above results indicate that subacute CdCl₂ exposure increase Cd content in the pig lungs, which leads to M1/M2 imbalance and down-regulates the content of LXA4/FPR2, further activates the oxidative stress/NF-κB/NLRP3 pathway, thereby activating the TGFβ and PPARγ/Wnt pathways to induce fibrosis. This study aims to reveal the toxic effects of CdCl₂ and will provide new insights into the toxicology of Cd.

Boosted Cr(VI) sorption coupled reduction from aqueous solution using quaternized algal/alginate@PEI beads

APEI beads (algal/alginate-PEI) were quaternized for enhancing the sorption of Cr(VI) (Q-APEI). The readily reduction of Cr(VI) into Cr(III) in acidic solution and in the presence of organic material constitute an additional phenomenon to be taken into account for the removal of Cr(VI) by Q-APEI. The optimal pH value for both the sorption and reduction of Cr(VI) was close to 2. The sorption isotherm was well described by the Sips model in batch system; the experimental maximum Cr(VI) sorption capacity of Q-APEI was 334 mg Cr(VI) g^-1, including a reduction yield close to 25%. The pseudo-second-order kinetic model (PSORE) and the Yan model fit the uptake kinetics and breakthrough curves, in a fixed-bed system with circulation or single-path modes, respectively. The mechanism of reduction-assisted sorption allows boosting the global removal of chromate. Furthermore, the testing of Cr(VI) for three successive sorption and desorption cycles shows the remarkable stability of the sorbent for Cr(VI) removal. The Cr(VI) sorption coupled reduction mechanism and interactions between the sorbent and Cr(VI) were further explained using Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS).

Recyclable Functionalized Material for Sensitive Detection and Exceptional Sorption of Hexavalent Chromium and Permanganate Ions with Biosensing Applications

Environmental remediation with a single platform for selective sensing and removal of toxic analytes with recyclability of the material has always been a desirable system for sustainability. However, materials comprising all the abovementioned advantages are rarely known for oxoanions. We herein developed a fluorogenic napthalimide-based functionalized mesoporous silica material (SiO₂@NBDBIA) as a signaling and remediation system for oxoanions (CrO₄^2-, Cr₂O₇^2-, and MnO₄^-) from a pool of several anions. The fluorescence quenching of the SiO₂@NBDBIA material in the presence of CrO₄^2-, Cr₂O₇^2-, and MnO₄^- ions gives the limit of detection (LOD) values of 6.23, 25.2, and 20.32 ppb, respectively, which are well below the maximum contaminant level demarcated by the United States Environmental Protection Agency. The maximum adsorption capacities of the material for the abovementioned oxoanions are found to be 352, 363, and 330 mg/g, respectively, which are well above those mentioned in the literature reports. Contrary to the literature-dominated irreversible ion-exchange mechanism, the reversible hydrogen-bonded binding of the material with the oxoanions leads to the recyclability of the material easily, which is very rare in the literature. The DFT calculations were performed to examine the interactions between the material and oxoanions. For real applications, this material was also used as a fluorescence probe to detect these oxoanions in the actual water samples, and more interestingly, used as a biosensing probe for these oxoanions in the living organism Artemia salina through fluorescence imaging. Thus, the SiO₂@NBDBIA material is a unique example of recyclable material for detecting and remediating oxoanions.

Phytoremediation of electroplating wastewater by vetiver grass (Chrysopogon zizanoides L.)

The electroplating industry generates wastewater containing a variety of heavy metals which potentially contaminate water ecosystems. The available and well-known electroplating wastewater treatments are considered as an expensive and less effective method, therefore phytoremediation was used as an alternative friendly solution. This study aims to evaluate the uptake and elimination rate of heavy metals by vetiver (Chrysopogon zizanoides L.) on metal-polluted water. Vetiver was planted in artificial electroplating wastewater containing different levels (low, medium, high) of chromium (Cr) and nickel (Ni). Water, roots, and shoots were collected periodically to determine Cr and Ni contents using Atomic Absorption Spectrometry (AAS). Metal accumulation and elimination rate, Bioconcentration Factor (BCF), Biological Absorption Coefficient (BAC), and Translocation Factor (TF) were calculated to evaluate plant's effectiveness in metal remediation processes. The results showed that vetiver (C. zizanoides L.) was able to remove 61.10% Cr and 95.65% Ni on metal-contaminated water. The highest uptake rates for Cr and Ni are 127.21 mg/kg/day and 15.60 mg/kg/day respectively, while the elimination rates for Cr and Ni tend to slow 1.09 mg/kg/day and 12.24 mg/kg/day respectively. Vetiver BCF, BAC, and TF values on Cr and Ni contaminated water were greater than 1, which indicates that vetiver work through phytoextraction and phytostabilization to treat metals. The findings showed that vetiver has promise as a phytoremediation agent thus providing implication for electroplating wastewater treatment.

Mechanism analysis of MnFe2O4/FeSX for removal of Cr(VI) from aqueous phase

By using Na₂S as a sulfur source, sulfur-doped MnFe₂O₄ was prepared using one-step solvent thermal method and utilized to remove hexavalent chromium. The materials were characterized through scanning electron microscopy, transmission electron microscopy, high-resolution TEM, X-ray diffraction, Fourier-transform infrared spectroscopy, Brunauer-Emmett-Teller method, zeta potential test, vibrating sample magnetometry, and X-ray photoelectron spectroscopy. When the pH was 3, the adsorption capacity of MnFe₂O₄/FeS_X-0.5 to Cr(VI) was 43.36 mg/g, which was roughly five times that of MnFe₂O₄ (8.90 mg/g). MnFe₂O₄/FeS_X-0.5 and MnFe₂O₄ fitted the Freundlich and pseudo-second-order kinetic models well. The electrochemical test analysis results showed that MnFe₂O₄/FeS_X had a faster MnFe₂O₄ electron transfer rate and higher electron transfer capacity than MnFe₂O₄, and thus promoted the reduction of Cr(VI) to Cr(III). This finding could be attributed to the lower electronegativity of the sulfur element than the oxygen element. In addition, the formation of additional FeS_X through sulfur doping improved the Cr(VI) removal ability of the prepared materials. The XPS and desorption results showed that more than 80% of the adsorbed Cr(VI) were reduced to Cr(III), which indicated that reduction was an important mechanism for Cr(VI) removal. This study verified that sulfur-doped manganese ferrite can be utilized in the high-efficiency removal of Cr(VI).

(3-Aminopropyl)triethoxysilane and iron rice straw biochar composites for the sorption of Cr (VI) and Zn (II) using the extract of heavy metals contaminated soil

Heavy metals like Cr (VI), when released into the environment, pose a serious threat to animal and human health. In this study, iron and (3-Aminopropyl)triethoxysilane (APTES) biochar composites were prepared from the biochar, which was produced through the pyrolysis of rice straw at 400 and 600 °C, using the chemical processes with an aim that the doping of pristine biochar structure with the Fe and NH₂ radicals would enhance the removal of Cr (VI) and Zn (II) adsorption in both aqueous solution and soil. Both biochar composites were mixed at a rate of 3% (w/w) with the mine soil for the soil incubation test, and after completion of the test, a soil fertility index (SFI) was calculated. Results showed that both iron and APTES biochar composites followed the Langmuir-Freundlich isotherm showing the maximum removal capacity of 100.59 mg/g for Cr (VI) by APTES/SiBC 600 and maximum adsorption capacity of 83.92 mg/g for Zn²⁺ by Fe/BC 400. The SFI of the mine-soil amended with both Fe and APTES biochar composites were 16.67 and 13.04%, respectively higher than the controlled study. The mitotic index of the A. cepa cells that grew up in the soil amended with Fe/BC and APTES/SiBC were 40.47 and 44.45%, respectively, higher than the controlled study. The results indicated that the incorporation of the Fe and APTES biochar composites in the soil effectively reduced the metal toxicity and improved the soil physicochemical properties. This study opens up the prospects of using biochar composites in contaminated soil and water treatments.

Adsorption of Cr (VI) onto micro- and nanoparticles of palygorskite in aqueous solutions: Effects of pH and humic acid

Palygorskite is a mineral widely applied for the removal of potentially toxic trace elements from the environment. This study aimed to identify the influence of pH (3, 4, 5, and 6) and humic acid (200 mg L^-1) addition on the adsorption of hexavalent chromium (Cr (VI)) ions by the microparticles and nanoparticles of palygorskite. Therefore, the mineral was prepared as the micron- and nano-sized particles saturated with Ba²⁺ ions, and finally used in adsorption experiments. The results indicated that regardless of the mineral size, Cr(VI) adsorption was enhanced by increasing the contact time from 5 to 2880 min and the equilibrium conditions achieved after 1440 min from the beginning of experiments. With increasing the pH values from 3 to 6, the adsorption efficiency of Cr(VI) decreased significantly, and the highest rate of removal (64%) was found at pH = 3. The pseudo-second-order model best described the kinetics of Cr(VI) adsorption onto both micro- and nanoparticles of palygorskite. Also, the experimental data showed maximum consistency with the data calculated by the Freundlich isotherm model. The two processes of film and pore diffusion were recognized as the main mechanisms that controlled the adsorption of Cr(VI) by palygorskite microparticles and nanoparticles. A comparison of the maximum adsorption capacity of Cr(VI) in different treatments followed the order of nanoparticles > humic acid > humic acid + nanoparticles ≈ humic acid + microparticles > microparticles. Accordingly, the adsorption capacities of "palygorskite nanoparticles" and "humic acid" for Cr(VI) ions were 3.7 and 3.2 times higher than that of palygorskite microparticles, respectively. Moreover, the adsorption capacities observed in the simultaneous application of humic acid with palygorskite microparticles and nanoparticles were 20% and 45% lower than those without humic acid, respectively. To conclude, palygorskite nanoparticles were found to have a significant adsorption capacity for Cr(VI) ions, which is negatively affected by rise in the pH of the aqueous matrix.