Highly efficient and stable 2D-3D perovskite solar cells fabricated by interfacial modification

High-Quality Hybrid Perovskite Thin Films by Post-Treatment Technologies in Photovoltaic Applications

Incredible progress in photovoltaic devices based on hybrid perovskite materials has been made in the past few decades, and a record-certified power conversion efficiency (PCE) of over 26% has been achieved in single-junction perovskite solar cells (PSCs). In the fabrication of high-efficiency PSCs, the postprocessing procedures toward perovskites are essential for designing high-quality perovskite thin films; developing efficient and reliable post-treatment techniques is very important to promote the progress of PSCs. Here, recent post-treatment technological reforms toward perovskite thin films are summarized, and the principal functions of the post-treatment strategies on the design of high-quality perovskite films have been thoroughly analyzed by dividing into two categories in this review: thermal annealing (TA)-related technique and TA-free technique. The latest research progress of the above two types of post-treatment techniques is summarized and discussed, focusing on the optimization of postprocessing conditions, the regulation of perovskite qualities, and the enhancement of device performance. Finally, an outlook of the prospect trends and future challenges for the fabrication of the perovskite layer and the production of highly efficient PSCs is given.

Improved Efficiency and Stability in 1,5-Diaminonaphthalene Iodide-Passivated 2D/3D Perovskite Solar Cells

Engineering multidimensional two-dimensional/three-dimensional (2D/3D) perovskite interfaces as light harvesters has recently emerged as a potential strategy to obtain a higher photovoltaic performance in perovskite solar cells (PSCs) with enhanced environmental stability. In this study, we utilized the 1,5-diammonium naphthalene iodide (NDAI) bulky organic spacer for interface modification in 3D perovskites for passivating the anionic iodide/uncoordinated Pb2+ vacancies as well as facilitating charge carrier transfer by improving the energy band alignment at the perovskite/HTL interface. Consequently, the NDAI-treated 2D/3D PSCs showed an enhanced open-circuit voltage and fill factor with a remarkable power conversion efficiency (PCE) of 21.48%. In addition, 2D/3D perovskite devices without encapsulation exhibit a 77% retention of their initial output after 1000 h of aging under 50 ± 5% relative humidity. Furthermore, even after 200 h of storage in 85 °C thermal stress, the devices maintain 60% of their initial PCE. The defect passivation and interface modification mechanism were studied in detail by UV vis absorption, photoluminescence spectroscopy, atomic force microscopy (AFM), scanning electron microscopy (SEM), Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS), solid-state NMR, space-charge-limited current (SCLC) mobility measurement, and impedance spectroscopy. This study provides a promising path for perovskite surface modification in slowing their degradation against external stimuli, providing a future direction for increasing the perovskite device efficiency and durability.

Synergistic Effect of Precursor and Interface Engineering Enables High Efficiencies in FAPbI3 Perovskite Solar Cells

Formamidinium lead iodide (FAPbI3)-based perovskite solar cells have gained immense popularity over the last few years within the perovskite research community due to their incredible opto-electronic properties and the record power conversion efficiencies (PCEs) achieved by the solar cells. However, FAPbI3 is vulnerable to phase transitions even at room temperature, which cause structural instability and eventual device failure during operation. We performed post-treatment of the FAPbI3 surface with octyl ammonium iodide (OAI) in order to stabilize the active phase and preserve the crystal structure of FAPbI3. The formation of a 2D perovskite at the interface depends on the stoichiometry of the precursor. By optimizing the precursor stoichiometry and the concentration of OAI, we observe a synergistic effect, which results in improved power conversion efficiencies, reaching the best values of 22% on a glass substrate. Using physical and detailed optical analysis, we verify the presence of the 2D layer on the top of the 3D surface of the perovskite film.

1D Choline-PbI3-Based Heterostructure Boosts Efficiency and Stability of CsPbI3 Perovskite Solar Cells

Defects in perovskite are key factors in limiting the photovoltaic performance and stability of perovskite solar cells (PSCs). Generally, choline halide (ChX) can effectively passivate defects by binding with charged point defects of perovskite. However, we verified that ChI can react with CsPbI3 to form a novel crystal phase of one-dimensional (1D) ChPbI3, which constructs 1D/3D heterostructure with 3D CsPbI3, passivating the defects of CsPbI3 more effectively and then resulting in significantly improved photoluminescence lifetime from 20.2 ns to 49.4 ns. Moreover, the outstanding chemical inertness of 1D ChPbI3 and the repair of undesired δ-CsPbI3 deficiency during its formation process can significantly enhance the stability of CsPbI3 film. Benefiting from 1D/3D heterostructure, CsPbI3 carbon-based PSCs (C-PSCs) delivered a champion efficiency of 18.05% and a new certified record of 17.8% in hole transport material (HTM)-free inorganic C-PSCs.

Self-healing 2D/3D perovskite for efficient and stable p-i-n perovskite solar cells

Beyond the p-i-n perovskite solar cell's high-power conversion efficiency (PCE), its moisture instability is the most challenging factor in its commercialization. Recently, the innovative use of three and two-dimensional multi-structures, by creating a barrier against the penetration of moisture and oxygen, has played a very influential role in improving the PSC's long-term stability. Here, a new strategy, the anti-solvent quenching method, is used to construct multi-structure perovskite by involving cetyltrimethylammonium bromide (CTAB) as an active agent. The solar cell efficiency is significantly improved during the perovskite formation on the substrate by creating a multidimensional (2D/3D) heterojunction perovskite. The synergistic role of using 2D/3D heterojunction perovskite structures led to the 29.2% improvement (14.58-18.84) in the PCE. The attractive ability of the 2D/3D active layer in self-healing has increased the perovskite's long-term stability under harsh environmental conditions.

Interfacial electronic properties of metal/CsSnBr3heterojunctions

All-inorganic lead-free perovskite CsSnBr₃, has been proved good stability and optoelectronic properties in theory and experiment. However, the interfacial electronic properties of metal/CsSnBr₃are still unclear in electronic devices. Herein, we systematically investigate the interfacial properties of metal electrodes (Al, Ag and Au) and CsSnBr₃with different atomic terminals (SnBr₂-T and CsBr-T) through the first-principles calculation. SnBr₂-T and CsBr-T have various contact types and Schottky barriers due to their different interaction strengths with metals. In particular, the moderate interlayer coupling strength with Al leads to the ultra-low Schottky barrier and tunneling barrier, which makes Al possess the best contact performance among the studied metals. Furthermore, the external electric field can be effective in regulating the Schottky barrier and realizing the Ohmic contact. These findings provide useful guidance for the design of perovskite-based nanoelectronic devices with high performance.

Methylammonium Compensation Effects in MAPbI3 Perovskite Solar Cells for High-Quality Inorganic CuSCN Hole Transport Layers

Recent studies have demonstrated that copper (I) thiocyanate (CuSCN) has huge potential as a hole extraction material (HEM) for perovskite solar cells. Here, we used CuSCN as a HEM and analyzed its relationships with a methylammonium lead iodide (MAPbI₃) perovskite layer. The CuSCN dissolved in diethyl sulfide (DES) was spin-coated on the MAPbI₃ layer. For high-quality and dense CuSCN layers, post-annealing was carried out at various temperatures and times. However, the unwanted dissociation of MAPbI₃ to PbI₂ was observed due to the post-annealing for a long time at elevated temperatures. In addition, DES, which is used as a CuSCN solvent, is a polar solvent that damages the surface of MAPbI₃ perovskites and causes poor interfacial properties between the perovskite layer and HEM. To solve this problem, the effect of the molar ratio of methylammonium iodide (MAI) and PbI₂ in the MAPbI₃ precursor solution was investigated. The excess MAI molar ratio in the MAPbI₃ precursor solution reduced MAPbI₃ surface damage despite using DES polar solvent for CuSCN solution. In addition, dissociation of MAPbI₃ to PbI₂ following an adequate post-annealing process was well suppressed. The excess MAI molar ratio in the MAPbI₃ precursor could be compensated for the MA loss and effectively suppress phase separation from MAPbI₃ to MAI + PbI₂ during post-annealing. The efficiency based on the normal planar structure of CuSCN/MAPbI₃ (using excess MAI)/TiO₂ was approximately 17%. The CuSCN-based MAPbI₃ device shows more optimized stability than the conventional spiro-OMeTAD under damp heat (85 °C and 85% relative humidity) conditions because of the robust inorganic HEM.

Surface Passivation Using 2D Perovskites toward Efficient and Stable Perovskite Solar Cells

3D perovskite solar cells (PSCs) have shown great promise for use in next-generation photovoltaic devices. However, some challenges need to be addressed before their commercial production, such as enormous defects formed on the surface, which result in severe SRH recombination, and inadequate material interplay between the composition, leading to thermal-, moisture-, and light-induced degradation. 2D perovskites, in which the organic layer functions as a protective barrier to block the erosion of moisture or ions, have recently emerged and attracted increasing attention because they exhibit significant robustness. Inspired by this, surface passivation by employing 2D perovskites deposited on the top of 3D counterparts has triggered a new wave of research to simultaneously achieve higher efficiency and stability. Herein, we exploited a vast amount of literature to comprehensively summarize the recent progress on 2D/3D heterostructure PSCs using surface passivation. The review begins with an introduction of the crystal structure, followed by the advantages of the combination of 2D and 3D perovskites. Then, the surface passivation strategies, optoelectronic properties, enhanced stability, and photovoltaic performance of 2D/3D PSCs are systematically discussed. Finally, the perspectives of passivation techniques using 2D perovskites to offer insight into further improved photovoltaic performance in the future are proposed.

The Influence of CsBr on Crystal Orientation and Optoelectronic Properties of MAPbI3-Based Solar Cells

Crystal orientations are closely related to the behavior of photogenerated charge carriers and are vital for controlling the optoelectronic properties of perovskite solar cells. Herein, we propose a facile approach to reveal the effect of lattice plane orientation distribution on the charge carrier kinetics via constructing CsBr-doped mixed cation perovskite phases. With grazing-incidence wide-angle X-ray scattering measurements, we investigate the crystallographic properties of mixed perovskite films at the microscopic scale and reveal the effect of the extrinsic CsBr doping on the stacking behavior of the lattice planes. Combined with transient photocurrent, transient photovoltage, and space-charge-limited current measurements, the transport dynamics and recombination of the photogenerated charge carriers are characterized. It is demonstrated that CsBr compositional engineering can significantly affect the perovskite crystal structure in terms of the orientation distribution of crystal planes and passivation of trap-state densities, as well as simultaneously facilitate the photogenerated charge carrier transport across the absorber and its interfaces. This strategy provides unique insight into the underlying relationship between the stacking pattern of crystal planes, photogenerated charge carrier transport, and optoelectronic properties of solar cells.

Nonmonotonic Photostability of BA2MAn-1PbnI3n+1 Homologous Layered Perovskites

Layered lead halide perovskites (2D LHPs) are attracting considerable attention as a promising material for a new generation of solar cell devices. LHPs have been presented as a more stable alternative to the more widespread 3D bulk perovskite materials; however, a critical analysis of their photostability is still lacking. In this work, we perform a comparative study between BA₂MA_n-1Pb_nI_3n+1 (BA─butylammonium and MA─methylammonium) 2D LHPs with different dimensionalities (n = 1-3) and MAPbI₃ 3D perovskites. We compare different stability testing protocols including photometrical determination of iodine-containing products in nonpolar solvents, X-ray diffraction, and photoluminescence (PL) spectroscopy. The resulting trends of the photostability in an inert atmosphere based on PL spectroscopy measurements demonstrate a nonmonotonic dependence of the degradation rate on the perovskite layer thickness n with a "stability island" at n ≥ 3, which is caused by a combination of antibate factors of electronic structures and chemical compositions in the family of 2D perovskites. We also identify a critical oxygen concentration in the surrounding environment that affects the mechanism and strongly enhances the rate of layered perovskite photodegradation.

Mostafa R, H. Zeenelabden H, M. Mabrouk M, Mourtada Elseman A, Gad N, El-Aasser M, M. Rashad M. Mixed 2D-3D Halide Perovskite Solar Cells

The 3D-perovskite halides have gained a considerable reputation versus their counterpart semiconductor materials since they achieved a remarkable high-power conversion efficiency of 25.2% within a decade. Perovskite solar cells also have some problems as lattice degradation and sensitivity against moisture, oxygen, and strong irradiation. The perovskite instability is the drawback in front of this emerging technology towards mass production and commercialization. 2D-perovskites, with the general formula A2Bn − 1MnX3n + 1, have been recently introduced to overcome some of the drawbacks of the stability of 3D-perovskites; however, this is at the expense of sacrificing a part of the power conversion efficiency. Mixed 2D/3D perovskites could solve this dilemma towards the way to high stability-efficiency perovskites. The research is expected to obtain highly stable and efficient mixed 2D/3D perovskite solar cells in the few coming years. This chapter reviews 2D-perovskites’ achieved progress, highlighting their properties, current trends, challenges, and future prospects.

Origin, Influence, and Countermeasures of Defects in Perovskite Solar Cells

Defects are considered to be one of the most significant factors that compromise the power conversion efficiencies and long-term stability of perovskite solar cells. Therefore, it is urgent to have a profound understanding of their formation and influence mechanism, so as to take corresponding measures to suppress or even completely eliminate their adverse effects on device performance. Herein, the possible origins of the defects in metal halide perovskite films and their impacts on the device performance are analyzed, and then various methods to reduce defect density are introduced in detail. Starting from the internal and interfacial aspects of the metal halide perovskite films, several ways to improve device performance and long-term stability including additive engineering, surface passivation, and other physical treatments (annealing engineering), etc., are further elaborated. Finally, the further understanding of defects and the development trend of passivation strategies are prospected.

Methods of Stability Control of Perovskite Solar Cells for High Efficiency

The increasing demand for renewable energy devices over the past decade has motivated researchers to develop new and improve the existing fabrication techniques. One of the promising candidates for renewable energy technology is metal halide perovskite, owning to its high power conversion efficiency and low processing cost. This work analyzes the relationship between the structure of metal halide perovskites and their properties along with the effect of alloying and other factors on device stability, as well as causes and mechanisms of material degradation. The present work discusses the existing approaches for enhancing the stability of PSC devices through modifying functional layers. The advantages and disadvantages of different methods in boosting device efficiency and reducing fabrication cost are highlighted. In addition, the paper presents recommendations for the enhancement of interfaces in PSC structures.

Nano-sized composite improving the insulating performance of insulating paper using low-temperature plasmas

Nanostructured dielectric composite has been considered as a promising manner in improving the flashover performance of oil-paper which has been widely used in power systems. In this paper, plasma-enhanced chemical vapor deposition (PECVD) is used to deposit SiO₂ on the ceramic fiber-reinforced insulating paper. Scanning electron microscope images show a large number of SiO₂ nanoparticles with diameters of 100 nm-250 nm uniformly attached to the fiber surface after the plasma deposition. The surface flashover voltage of the insulating paper was tested in the air and the transformer oil, respectively. Results show that the corresponding DC surface flashover voltages increased by 15.1% in the air and breakdown between liquid and solid interface increased by 24.6% after the PECVD. It is believed that nanoparticles constructed in ceramic fibers change the electron injection barrier which inhibits the injection of negative charges and hinders the accumulation of charges in the dielectric. Nanoparticles can capture electric charges formed in the transformer oil which affects the generation and development of streamers, resulting in an increased dielectric strength. This study provides a new method to comprehensively improve the surface insulating property which has the prospect of promoting other dielectric materials.

Long-Term Stability Analysis of 3D and 2D/3D Hybrid Perovskite Solar Cells Using Electrochemical Impedance Spectroscopy

Despite the remarkable progress in perovskite solar cells (PSCs), their instability and rapid degradation over time still restrict their commercialization. A 2D capping layer has been proved to overcome the stability issues; however, an in-depth understanding of the complex degradation processes over a prolonged time at PSC interfaces is crucial for improving their stability. In the current work, we investigated the stability of a triple cation 3D ([(FA0.83MA0.17)Cs0.05]Pb(I0.83Br0.17)3) and 2D/3D PSC fabricated by a layer-by-layer deposition technique (PEAI-based 2D layer over triple cation 3D perovskite) using a state-of-art characterization technique: electrochemical impedance spectroscopy (EIS). A long-term stability test over 24 months was performed on the 3D and 2D/3D PSCs with an initial PCE of 18.87% and 20.21%, respectively, to suggest a more practical scenario. The current-voltage (J-V) and EIS results showed degradation in both the solar cell types; however, a slower degradation rate was observed in 2D/3D PSCs. Finally, the quantitative analysis of the key EIS parameters affected by the degradation in 3D and 2D/3D PSCs were discussed.

In Situ Formation of Mixed-Dimensional Surface Passivation Layers in Perovskite Solar Cells with Dual-Isomer Alkylammonium Cations

Dimensional engineering of perovskite solar cells has attracted significant research attention recently because of the potential to improve both device performance and stability. Here, a novel 2D passivation scheme for 3D perovskite solar cells is demonstrated using a mixed cation composition of 2D perovskite based on two different isomers of butylammonium iodide. The dual-cation 2D perovskite outperforms its single cation 2D counterparts in surface passivation quality, resulting in devices with an impressive open-circuit voltage of 1.21 V for a perovskite composition with an optical bandgap of ≈1.6 eV, and a champion efficiency of 23.27%. Using a combination of surface elemental analysis and valence electron spectra decomposition, it is shown that an in situ interaction between the 2D perovskite precursor and the 3D active layer results in surface intermixing of 3D and 2D perovskite phases, providing an effective combination of defect passivation and enhanced charge transfer, despite the semi-insulating nature of the 2D perovskite phase. The demonstration of the synergistic interaction of multiple organic spacer cations in a 2D passivation layer offers new opportunities for further enhancement of device performance with mixed dimensional perovskite solar cells.

Sodium Dodecylbenzene Sulfonate Interface Modification of Methylammonium Lead Iodide for Surface Passivation of Perovskite Solar Cells

Perovskite solar cells (PSCs) have been developed as a promising photovoltaic technology because of their excellent photovoltaic performance. However, interfacial recombination and charge carrier transport losses at the surface greatly limit the performance and stability of PSCs. In this work, the fabrication of high-quality PSCs based on methylammonium lead iodide with excellent ambient stability is reported. An anionic surfactant, sodium dodecylbenzene sulfonate (SDBS), is introduced to simultaneously passivate the defect states and stabilize the cubic phase of the perovskite film. The SDBS located at grain boundaries and the surface of the active layer can effectively passivate under-coordinated lead ions and protect the perovskite components from water-induced degradation. As a result, a champion power conversion efficiency (PCE) of 19.42% is achieved with an open-circuit voltage (V_OC) of 1.12 V, a short-circuit current (J_SC) of 23.23 mA cm^-2, and a fill factor (FF) of 74% in combination with superior moisture stability. The SDBS-passivated devices retain 80% of their initial average PCE after 2112 h of storage under ambient conditions.

Distinguishing Energy- and Charge-Transfer Processes in Layered Perovskite Quantum Wells with Two-Dimensional Action Spectroscopies

Interest in photovoltaic devices based on layered perovskites is motivated by their tunable optoelectronic properties and stabilities in humid conditions. In these systems, quantum wells with different sizes are organized to direct energy and charge transport between electrodes; however, these relaxation mechanisms are difficult to distinguish based on conventional transient absorption techniques. Here, two-dimensional "action spectroscopies" are employed to separately target processes that lead to the production of photocurrent and energy loss due to fluorescence emission. These measurements show that energy transfer between quantum wells dominates the subnanosecond time scale, whereas electron transfer occurs at later times. Overall, this study suggests that while the intense exciton transitions promote light harvesting, much of the absorbed energy is lost by way of spontaneous emission. This limitation may be overcome with alternate layered perovskite systems that combine smaller exciton binding energies with large absorbance cross sections in the visible spectral range.

Improved Performance of CH3NH3PbI3-xClx Resistive Switching Memory by Assembling 2D/3D Perovskite Heterostructures

The rapidly growing demand for fast information storage and processing has driven the development of resistive random access memories (RRAMs). Recently, RRAMs based on organometal halide perovskite materials have been reported to have promising memory properties, which are essential for next-generation memory devices. In this study, a hybrid two-dimensional/three-dimensional (2D/3D) perovskite heterostructure has been created by depositing n-butylammonium iodide on top of the CH₃NH₃PbI_3-xCl_x (MAPbI_3-xCl_x) surface. The perovskite film is fabricated by a facile one-step spin-coating method with room-temperature molten salt methylammonium acetate in the air. Resistive switching memory devices with a 2D/3D perovskite heterostructure exhibit a significantly improved switching window (ON/OFF ratio over 10³) with a lower operation voltage compared with their 3D counterparts. The 2D/3D perovskite heterostructure is advantageous for fabricating uniform-crystalline-grain, highly compact structures and can passivate defect states for the MAPbI_3-xCl_x film and the interface, which results in improved memory properties. These results provide a new perspective for developing high-performance perovskite-based memory devices.