Genetic engineering of algae for enhanced biofuel production

NADP+-dependent isocitrate dehydrogenase as a novel target for altering carbon flux to lipid accumulation and enhancing antioxidant capacity in Tetradesmus obliquus

Regulatory complexities in lipogenesis hinder the harmonization of metabolic carbon precursors towards lipid synthesis. Exploring regulatory complexities in lipogenesis, this study identifies NADP+-dependent isocitrate dehydrogenase (IDH) in Tetradesmus obliquus as a key factor. Overexpression IDH in strains ToIDH-1 and ToIDH-2 resulted in a 1.69 and 1.64-fold increase in neutral lipids, respectively, compared to the wild type, with lipid yield reaching 234.56 and 227.17 mg/L. Notably, despite slower growth, the cellular biomass augmented to 790.67 mg/L. Metabolite analysis indicated a shift in carbon precursors from protein to lipid and carbohydrate synthesis. Morphological observations revealed increases in the volume and number of lipid droplets, alongside a change in the fatty acid profile favoring monounsaturated and saturated fatty acids. Furthermore, IDH overexpression enhanced NADPH production and antioxidant activity, thereby further boosting lipid accumulation when combined with salt stress. This study suggests a pathway for improved lipogenesis and algal growth via metabolic engineering.

Exceptional Quantum Efficiency Powers Biomass Production in Halotolerant Algae Picochlorum sp.. PHOTOSYNTHESIS RESEARCH 2024:10.1007/s11120-024-01075-9. [PMID: 38329705 DOI: 10.1007/s11120-024-01075-9] [Citation(s) in RCA: 0] [Impact Index Per Article: 0]

The green algal genus Picochlorum is of biotechnological interest because of its robust response to multiple environmental stresses. We compared the metabolic performance of P. SE3 and P. oklahomense to diverse microbial phototrophs and observed exceptional performance of photosystem II (PSII) in light energy conversion in both Picochlorum species. The quantum yield (QY) for O2 evolution is the highest of any phototroph yet observed, 32% (20%) by P. SE3 (P. okl) when normalized to total PSII subunit PsbA (D1) protein, and 80% (75%) normalized per active PSII, respectively. Three factors contribute: (1) an efficient water oxidizing complex (WOC) with the fewest photochemical misses of any organism; (2) faster reoxidation of reduced (PQH2)B in P. SE3 than in P. okl. (period-2 Fourier amplitude); and (3) rapid reoxidation of the plastoquinol pool by downstream electron carriers (Cyt b6f/PETC) that regenerates PQ faster in P. SE3. This performance gain is achieved without significant residue changes around the QB site and thus points to a pull mechanism involving faster PQH2 reoxidation by Cyt b6f/PETC that offsets charge recombination. This high flux in P. SE3 may be explained by genomically encoded plastoquinol terminal oxidases 1 and 2, whereas P. oklahomense has neither. Our results suggest two distinct types of PSII centers exist, one specializing in linear electron flow and the other in PSII-cyclic electron flow. Several amino acids within D1 differ from those in the low-light-descended D1 sequences conserved in Viridiplantae, and more closely match those in cyanobacterial high-light D1 isoforms, including changes near tyrosine Yz and a water/proton channel near the WOC. These residue changes may contribute to the exceptional performance of Picochlorum at high-light intensities by increasing the water oxidation efficiency and the electron/proton flux through the PSII acceptors (QAQB).

Using directed evolution to improve hydrogen production in chimeric hydrogenases from algal species

Algae generate hydrogen from sunlight and water utilizing high-energy electrons generated during photosynthesis. The amount of hydrogen produced in heterologous expression of the wild-type hydrogenase is currently insufficient for industrial applications. One approach to improve hydrogen yields is through directed evolution of the DNA of the native hydrogenase. Here, we created 113 chimeric algal hydrogenase gene variants derived from combining segments of three parent hydrogenases, two from Chlamydomonas reinhardtii (CrHydA1 and CrHydA2) and one from Scenedesmus obliquus (HydA1). To generate chimeras, there were seven segments into which each of the parent hydrogenase genes was divided and recombined in a variety of combinations. The chimeric and parental hydrogenase sequences were cloned for heterologous expression in Escherichia coli, and 40 of the resultant enzymes expressed were assayed for H2 production. Chimeric clones that resulted in equal or greater production obtained with the cloned CrHydA1 parent hydrogenase were those comprised of CrHydA1 sequence in segments #1, 2, 3, and/or 4. These best-performing chimeras all contained one common region, segment #2, the part of the sequence known to contain important amino acids involved in proton transfer or hydrogen cluster coordination. The amino acid sequence distances among all chimeric clones to that of the CrHydA1 parent were determined, and the relationship between sequence distances and experimentally-derived H2 production was evaluated. An additional model determined the correlation between electrostatic potential energy surface area ratios and H2 production. The model yielded several algal mutants with predicted hydrogen productions in a range of two to three times that of the wild-type hydrogenase. The mutant data and the model can now be used to predict which specific mutant sequences may result in even higher hydrogen yields. Overall, results provide more precise details in planning future directed evolution to functionally improve algal hydrogenases.

Investigating the impact of n-heptane (C7H16) and nanoparticles (TiO2) on diesel-microalgae biodiesel blend in CI diesel engines

Recent global challenges encompass profound environmental pollution and the depletion of finite fuel resources. In this study, the biodiesel used in the mixture was derived from Azolla pinnata microalgae oil through a trans-esterification reaction chosen for its high oil concentration. During the initial phase of the experiment, varying volumes of biodiesel (5%, 10%, and 15%) and n-heptane (5%, 10%, and 15%) were introduced to diesel to form a ternary fuel blend. The experimental outcome shows that an n-heptane and biodiesel mixture of 10% by volume would produce the best results. Next, experiments were carried out by incorporating 10, 40, and 80 ppm titanium oxide (TiO2) nanoparticles (NPs) in a recommended ternary fuel blend. The experimental investigation showed that D80A10H10TNP40 (diesel 80% + biodiesel 10% + n-heptane 10% + TiO2 40 ppm) caused a 7.21% increase in brake thermal efficiency (BTE) with a decrease in brake specific fuel consumption (BSFC) and brake specific energy consumption (BSEC) by 9.58% and 10%, respectively, compared to (diesel 80% + biodiesel 20%) D80A20. D80A10H10TNP40 exhibits lower emissions, with a significant reduction of 11.29% and 20.96% in carbon monoxide (CO) and unburnt hydrocarbons (UBHC), respectively. Nitrogen oxide (NOX) and smoke emissions were reduced by 3.3% and 11.13%, respectively, compared to D80A10H10. Furthermore, D80A10H10TNP40 demonstrated enhanced combustion properties, comprising a significant rise of 4.39% in-cylinder pressure (CP), 35.29% in heat release rate (HRR), and 25.05% in the rate of pressure rise (RPR). The findings of this investigation indicate that D80A10H10TNP40 exhibits enhanced efficiency, emission, and combustion properties compared to the D80A20 fuel.

Simple and Effective Squash-PCR for Rapid Genotyping of Industrial Microalgae

Microalgae are recognized for their versatility in providing renewable energy, biopharmaceuticals, and nutraceuticals, attributed to their sustainable, renewable, and cost-effective nature. Genetic engineering has proven highly effective in enhancing microalgae production. PCR-based genotyping is the primary method for screening genetically transformed microalgae cells. Recently, we developed a novel PCR method, namely Squash-PCR, and employed it for the molecular analysis of industrially important fungi and yeasts. In this study, we successfully implemented the Squash-PCR technique in 12 industrially significant algae species. This approach offers a quick and reliable means of obtaining DNA templates directly from squashed algal cells, eliminating the need for time-consuming and labor-intensive cultivation and genomic DNA extraction steps. Our results demonstrate the effectiveness of Squash-PCR in detecting and characterizing target genes of interest in 12 different algae species. Overall, this study establishes the Squash-PCR method as a valuable tool for molecular studies in algae, enabling researchers to rapidly screen and manipulate genetic traits in diverse algal species.

Enhanced extracellular ammonium release in the plant endophyte Gluconacetobacter diazotrophicus through genome editing

IMPORTANCE

Our results demonstrate increased extracellular ammonium release in the endophyte plant growth-promoting bacterium Gluconacetobacter diazotrophicus. Strains were constructed in a manner that leaves no antibiotic markers behind, such that these strains contain no transgenes. Levels of ammonium achieved by cultures of modified G. diazotrophicus strains reached concentrations of approximately 18 mM ammonium, while wild-type G. diazotrophicus remained much lower (below 50 µM). These findings demonstrate a strong potential for further improving the biofertilizer potential of this important microbe.

Understanding Macroalgae: A Comprehensive Exploration of Nutraceutical, Pharmaceutical, and Omics Dimensions

Driven by a surge in global interest in natural products, macroalgae or seaweed, has emerged as a prime source for nutraceuticals and pharmaceutical applications. Characterized by remarkable genetic diversity and a crucial role in marine ecosystems, these organisms offer not only substantial nutritional value in proteins, fibers, vitamins, and minerals, but also a diverse array of bioactive molecules with promising pharmaceutical properties. Furthermore, macroalgae produce approximately 80% of the oxygen in the atmosphere, highlighting their ecological significance. The unique combination of nutritional and bioactive attributes positions macroalgae as an ideal resource for food and medicine in various regions worldwide. This comprehensive review consolidates the latest advancements in the field, elucidating the potential applications of macroalgae in developing nutraceuticals and therapeutics. The review emphasizes the pivotal role of omics approaches in deepening our understanding of macroalgae's physiological and molecular characteristics. By highlighting the importance of omics, this review also advocates for continued exploration and utilization of these extraordinary marine organisms in diverse domains, including drug discovery, functional foods, and other industrial applications. The multifaceted potential of macroalgae warrants further research and development to unlock their full benefits and contribute to advancing global health and sustainable industries.

Reconstruction of a Genome-Scale Metabolic Model of Scenedesmus obliquus and Its Application for Lipid Production under Three Trophic Modes

Green microalgae have emerged as beneficial feedstocks for biofuel production. A systems-level understanding of the biochemical network is needed to harness the microalgal metabolic capacity for bioproduction. Genome-scale metabolic modeling (GEM) showed immense potential in rational metabolic engineering, utilizing biochemical flux distribution analysis. Here, we report the first GEM for the green microalga, Scenedesmus obliquus (iAR632), a promising biodiesel feedstock with high lipid-storing capability. iAR632 comprises 1467 reactions, 734 metabolites, and 632 genes distributed among 7 compartments. The model was optimized under three different trophic modes of microalgal cultivation, i.e., autotrophy, mixotrophy, and heterotrophy. The robustness of the reconstructed network was confirmed by analyzing its sensitivity to the biomass components. Pathway-level flux profiles were analyzed, and significant flux space expansion was noticed majorly in reactions associated with lipid biosynthesis. In agreement with the experimental observation, iAR632 predicted about 3.8-fold increased biomass and almost 4-fold higher lipid under mixotrophy than the other trophic modes. Thus, the assessment of the condition-specific metabolic flux distribution of iAR632 suggested that mixotrophy is the preferred cultivation condition for improved microalgal growth and lipid production. Overall, the reconstructed GEM and subsequent analyses will provide a systematic framework for developing model-driven strategies to improve microalgal bioproduction.

Extraction methods of algae oils for the production of third generation biofuels - A review

Microalgae are the main source of third-generation biofuels because they have a lipid content of 20-70%, can be abundantly produced and do not compete in the food market besides other benefits. Biofuel production from microalgae is a promising option to contribute for the resolution of the eminent crisis of fossil energy and environmental pollution specially in the transporting sector. The choice of lipid extraction method is of relevance and associated to the algae morphology (i.e., rigid cells). Therefore, it is essential to develop suitable extraction technologies for economically viable and environment-friendly lipid recovery processes with the aim of achieving a commercial production of biofuels from this biomass. This review presents an exhaustive analysis and discussion of different methods and processes of lipid extraction from microalgae for the subsequent conversion to biodiesel. Physical methods based on the use of supercritical fluids, ultrasound and microwaves were reviewed. Chemical methods using solvents with different polarities, aside from mechanical techniques such as mechanical pressure and enzymatic methods, were also analyzed. The advantages, drawbacks, challenges and future prospects of lipid extraction methods from microalgae have been summarized to provide a wide panorama of this relevant topic for the production of economic and sustainable energy worldwide.

A critical review on phycoremediation of pollutants from wastewater-a novel algae-based secondary treatment with the opportunities of production of value-added products

Though the biological treatment employing bacterial strains has wide application in effluent treatment plant, it has got several limitations. Researches hence while looking for alternative biological organisms that can be used for secondary treatment came up with the idea of using microalgae. Since then, a large number of microalgal/cyanobacterial strains have been identified that can efficiently remove pollutants from wastewater. Some researchers also found out that the algal biomass not only acts as a carbon sink by taking up carbon dioxide from the atmosphere and giving oxygen but also is a renewable source of several value-added products that can be extracted from it for the commercial use. In this work, the cleaning effect of different species of microalgae/cyanobacteria on wastewater from varied sources along with the value-added products obtained from the algal biomass as observed by researchers during the past few years are reviewed. While a number of review works in the field of phycoremediation technology was reported in literature, a comprehensive study on phycoremediation of wastewater from different industries and household individually is limited. In the present review work, the efficiency of diverse microalgal/cyanobacterial strains in treatment of wide range of industrial effluents along with municipal wastewater having multi-pollutants has been critically reviewed.

CRISPR-based bioengineering in microalgae for production of industrially important biomolecules

Microalgae, as photosynthetic organisms, have the potential to produce biomolecules for use in food, feed, cosmetics, nutraceuticals, fuel, and other applications. Faster growth rates and higher protein and lipid content make microalgae a popular chassis for many industrial applications. However, challenges such as low productivity and high production costs have limited their commercialization. To overcome these challenges, bioengineering approaches such as genetic engineering, metabolic engineering, and synthetic biology have been employed to improve the productivity and quality of microalgae-based products. Genetic engineering employing genome editing tools like CRISPR/Cas allows precise and targeted genetic modifications. CRISPR/Cas systems are presently used to modify the genetic makeup of microalgae for enhanced production of specific biomolecules. However, these tools are yet to be explored explicitly in microalgae owing to some limitations. Despite the progress made in CRISPR-based bioengineering approaches, there is still a need for further research to optimize the production of microalgae-based products. This includes improving the efficiency of genome editing tools, understanding the regulatory mechanisms of microalgal metabolism, and optimizing growth conditions and cultivation strategies. Additionally, addressing the ethical, social, and environmental concerns associated with genetic modification of microalgae is crucial for the responsible development and commercialization of microalgae-based products. This review summarizes the advancements of CRISPR-based bioengineering for production of industrially important biomolecules and provides key considerations to use CRISPR/Cas systems in microalgae. The review will help researchers to understand the progress and to initiate genome editing experiments in microalgae.

Alkaline Phosphatase PhoD Mutation Induces Fatty Acid and Long-Chain Polyunsaturated Fatty Acid (LC-PUFA)-Bound Phospholipid Production in the Model Diatom Phaeodactylum tricornutum

With rapid growth and high lipid contents, microalgae have become promising environmentally friendly candidates for renewable biodiesel and health supplements in our era of global warming and energy depletion. Various pathways have been explored to enhance algal lipid production, especially gene editing. Previously, we found that the functional loss of PhoD-type alkaline phosphatase (AP), a phosphorus-stress indicator in phytoplankton, could lead to increased lipid contents in the model diatom Phaeodactylum tricornutum, but how the AP mutation may change lipid composition remains unexplored. This study addresses the gap in the research and investigates the effects of PhoD-type AP mutation on the lipid composition and metabolic regulation in P. tricornutum using transcriptomic and lipidomic analyses. We observed significantly modified lipid composition and elevated production of fatty acids, lysophosphatidylcholine, lysophosphatidylethanolamine, ceramide, phosphatidylinositol bisphosphate, and monogalactosylmonoacylglycerol after PhoD_45757 mutation. Meanwhile, genes involved in fatty acid biosynthesis were upregulated in mutant cells. Moreover, the mutant exhibited increased contents of ω-3 long-chain polyunsaturated fatty acid (LC-PUFA)-bound phospholipids, indicating that PhoD_45757 mutation could improve the potential bioavailability of PUFAs. Our findings indicate that AP mutation could influence cellular lipid synthesis and probably redirect carbon toward lipid production and further demonstrate that AP mutation is a promising approach for the development of high-value microalgal strains for biomedical and other applications.

Alternative carbon sources for the production of plant cellular agriculture: a case study on acetate

Plant cellular agriculture aims to disrupt the way plant derived products are produced. Plant cell cultures are typically grown with sucrose as the primary carbon and energy source, but alternative carbon sources may have advantages over sucrose including less strain on food systems, lower costs, and more sustainable sourcing. Here we review carbon and energy sources that may serve as alternatives to sucrose in the cultivation of plant cell cultures. We identified acetate as a promising candidate and took the first steps to evaluate its potential for use in growing tobacco plant cell cultures. When added to media containing sucrose, acetate concentrations above 8 mM completely inhibit growth. Lower concentrations of acetate (2-4 mM) can support an increase in dry weight without sucrose but do not provide enough energy for substantial growth. 13C labeling indicates that tobacco plant cell cultures can incorporate carbon from exogenous acetate into proteins and carbohydrates. Analysis of transcriptome data showed that genes encoding glyoxylate cycle enzymes are expressed at very low levels compared to genes from the TCA cycle and glycolysis. Adaptive laboratory evolution experiments were able to increase tobacco cell cultures tolerance to acetate, demonstrating the potential for this type of approach going forward. Overall, our results indicate that acetate can be metabolized by plant cell cultures and suggest that further adaptive laboratory evolution or strain engineering efforts may enable acetate to serve as a sole carbon and energy source for tobacco plant cell cultures. This assessment of acetate provides a framework for evaluating other carbon and energy sources for plant cell cultures, efforts that will help reduce the costs and environmental impact, and increase the commercial potential of plant cellular agriculture.

Light intensity and spectral quality modulation for improved growth kinetics and biochemical composition of Chlamydomonas reinhardtii

Effective strategies to optimize algal growth and lipid productivity are critical for the sustainable production of biomass for various applications. Light management has emerged as a promising approach, but the intricate relationship between light intensity, spectral quality, and algal responses remains poorly understood. This study investigated the effects of different light qualities (blue, red-orange, and white-yellow) and intensities (45-305 μmol/m2·s) on Chlamydomonas reinhardtii. Red-orange light exhibited the highest promotion of biomass growth and lipid productivity, with specific growth rates of 1.968 (d-1) and biomass productivity of 0.284 (g/L/d) at 155 μmol/m2·s and 205 μmol/m2·s, respectively. Within the intensity range of 205 μmol/m2·s to 305 μmol/m2·s, lipid mass fractions ranged from 10.5% w/w to 11.0% w/w, accompanied by lipid concentrations ranging from 68.6 mg/L to 74.9 mg/L. Red-orange light positively influenced carbohydrate accumulation, while blue light promoted protein synthesis. These findings highlight the importance of optimizing light quality and intensity to enhance algal biomass productivity and manipulate biochemical composition. Understanding the complex relationship between light parameters and algal physiology will contribute to sustainable algal cultivation practices and the use of microalgae as a valuable bioresource.

Overview and Challenges of Large-Scale Cultivation of Photosynthetic Microalgae and Cyanobacteria

Microalgae and cyanobacteria are diverse groups of organisms with great potential to benefit societies across the world. These organisms are currently used in food, feed, pharmaceutical and cosmetic industries. In addition, a variety of novel compounds are being isolated. Commercial production of photosynthetic microalgae and cyanobacteria requires cultivation on a large scale with high throughput. However, scaling up production from lab-based systems to large-scale systems is a complex and potentially costly endeavor. In this review, we summarise all aspects of large-scale cultivation, including aims of cultivation, species selection, types of cultivation (ponds, photobioreactors, and biofilms), water and nutrient sources, temperature, light and mixing, monitoring, contamination, harvesting strategies, and potential environmental risks. Importantly, we also present practical recommendations and discuss challenges of profitable large-scale systems associated with economical design, effective operation and maintenance, automation, and shortage of experienced phycologists.

Site-specific gene knock-in and bacterial phytase gene expression in Chlamydomonas reinhardtii via Cas9 RNP-mediated HDR

In the present study, we applied the HDR (homology-directed DNA repair) CRISPR-Cas9-mediated knock-in system to accurately insert an optimized foreign bacterial phytase gene at a specific site of the nitrate reductase (NR) gene (exon 2) to achieve homologous recombination with the stability of the transgene and reduce insertion site effects or gene silencing. To this end, we successfully knocked-in the targeted NR gene of Chlamydomonas reinhardtii using the bacterial phytase gene cassette through direct delivery of the CRISPR/Cas9 system as the ribonucleoprotein (RNP) complex consisting of Cas9 protein and the specific single guide RNAs (sgRNAs). The NR insertion site editing was confirmed by PCR and sequencing of the transgene positive clones. Moreover, 24 clones with correct editing were obtained, where the phytase gene cassette was located in exon 2 of the NR gene, and the editing efficiency was determined to be 14.81%. Additionally, site-specific gene expression was analyzed and confirmed using RT-qPCR. Cultivation of the positive knocked-in colonies on the selective media during 10 generations indicated the stability of the correct editing without gene silencing or negative insertion site effects. Our results demonstrated that CRISPR-Cas9-mediated knock-in could be applied for nuclear expression of the heterologous gene of interest, and also confirmed its efficacy as an effective tool for site-specific gene knock-in, avoiding nuclear positional effects and gene silencing in C. reinhardtii. These findings could also provide a new perspective on the advantageous application of RNP-CRISPR/Cas9 gene-editing to accelerate the commercial production of complex recombinant proteins in the food-grade organism "C. reinhardtii".

Ethical and social insights into synthetic biology: predicting research fronts in the post-COVID-19 era

As a revolutionary biological science and technology, synthetic biology has already spread its influence from natural sciences to humanities and social sciences by introducing biosafety, biosecurity, and ethical issues to society. The current study aims to elaborate the intellectual bases and research front of the synthetic biology field in the sphere of philosophy, ethics, and social sciences, with knowledge mapping and bibliometric methods. The literature records from the Social Sciences Citation Index and Arts & Humanities Citation Index in the Web of Science Core Collection from 1982 to 2021 were collected and analyzed to illustrate the intellectual structure of philosophical, ethical, and social research of synthetic biology. This study profiled the hotspots of research focus on its governance, philosophical and ethical concerns, and relevant technologies. This study offers clues and enlightenment for the stakeholders and researchers to follow the progress of this emerging discipline and technology and to understand the cutting-edge ideas and future form of this field, which takes on greater significance in the post-COVID-19 era.

Effect of EPS production on the performance of membrane-based biofilm reactors

This study explored the effect of extracellular polymeric substance (EPS) production on the performance of membrane-based biofilm reactors. Changing EPS production was induced by eliminating one of the main EPS polysaccharides, i.e., Pel. The studies were carried out using a pure culture of either Pseudomonas aeruginosa or an isogenic P. aeruginosa mutant that was unable to produce the Pel polysaccharide. The biofilm cell density for both strains was compared to confirm the Pel deletion mutant decreased overall EPS production in a bioreactor system. When the Pel-deficient mutant was grown as a biofilm, its cell density, i.e., ratio of cells/(cells + EPS), was 74 % higher than the wild type, showing EPS production was reduced by eliminating pel production. The growth kinetics were determined for both strains. The Pel-deficient mutant had a maximum specific growth rate (μ^) that was 14% higher than the wild type. Next, the effects of EPS reduction on reactor performance were assessed for a membrane aerated biofilm reactor (MABR) and a membrane bioreactor (MBR). For the MABR, the organic removal with the Pel-deficient mutant was around 8% higher than for the wild type. For the MBR, the time to reach the fouling threshold was 65 % greater for the Pel-deficient mutant than for the wild type. These results suggest that amount of EPS production can have significant effects on bacterial growth kinetics and bacterial cell density, which in turn can affect the performance of the membrane-based biofilm reactors. In both cases, lower EPS production correlated with more efficient treatment processes.

CO2 gradient domestication improved high-concentration CO2 tolerance and photoautotrophic growth of Euglena gracilis

In order to improve CO₂ biofixation efficiency of microalgae cultivated with coal-chemical flue gas, CO₂ gradient domestication was employed to improve high-concentration CO₂ tolerance and photoautotrophic growth of acid-tolerant Euglena gracilis. The dried biomass yield of photoautotrophic growth of E.gracilis increased from 1.09 g/L (wild-type strain) by 21 % to 1.32 g/L with CO₂ gradient domestication to 15 % CO₂. The RuBisCO activity and biomass production of E.gracilis strain domesticated to 99 % CO₂ were 2.63 and 3.4 times higher, respectively, than those of wild-type strain. The chlorophyll a and b contents were 2.52 and 1.79 times higher, respectively, than those of wild-type strain. Superoxide dismutase and catalase activities of 99 % CO₂-domesticated strain increased to 1.24 and 6 times, which reduced peroxide damage under high carbon stress and resulted in lower apoptotic and necrotic rates of domesticated strain. Thus, this work provides valuable guidance for CO₂ fixation and adaptive evolution of E. gracilis in industrial flue gas.

Cyanobacteria as cell factories for the photosynthetic production of sucrose

Biofuels and other biologically manufactured sustainable goods are growing in popularity and demand. Carbohydrate feedstocks required for industrial fermentation processes have traditionally been supplied by plant biomass, but the large quantities required to produce replacement commodity products may prevent the long-term feasibility of this approach without alternative strategies to produce sugar feedstocks. Cyanobacteria are under consideration as potential candidates for sustainable production of carbohydrate feedstocks, with potentially lower land and water requirements relative to plants. Several cyanobacterial strains have been genetically engineered to export significant quantities of sugars, especially sucrose. Sucrose is not only naturally synthesized and accumulated by cyanobacteria as a compatible solute to tolerate high salt environments, but also an easily fermentable disaccharide used by many heterotrophic bacteria as a carbon source. In this review, we provide a comprehensive summary of the current knowledge of the endogenous cyanobacterial sucrose synthesis and degradation pathways. We also summarize genetic modifications that have been found to increase sucrose production and secretion. Finally, we consider the current state of synthetic microbial consortia that rely on sugar-secreting cyanobacterial strains, which are co-cultivated alongside heterotrophic microbes able to directly convert the sugars into higher-value compounds (e.g., polyhydroxybutyrates, 3-hydroxypropionic acid, or dyes) in a single-pot reaction. We summarize recent advances reported in such cyanobacteria/heterotroph co-cultivation strategies and provide a perspective on future developments that are likely required to realize their bioindustrial potential.

Genetic engineering to enhance microalgal-based produced water treatment with emphasis on CRISPR/Cas9: A review

In recent years, the increased demand for and regional variability of available water resources, along with sustainable water supply planning, have driven interest in the reuse of produced water. Reusing produced water can provide important economic, social, and environmental benefits, particularly in water-scarce regions. Therefore, efficient wastewater treatment is a crucial step prior to reuse to meet the requirements for use within the oil and gas industry or by external users. Bioremediation using microalgae has received increased interest as a method for produced water treatment for removing not only major contaminants such as nitrogen and phosphorus, but also heavy metals and hydrocarbons. Some research publications reported nearly 100% removal of total hydrocarbons, total nitrogen, ammonium nitrogen, and iron when using microalgae to treat produced water. Enhancing microalgal removal efficiency as well as growth rate, in the presence of such relevant contaminants is of great interest to many industries to further optimize the process. One novel approach to further enhancing algal capabilities and phytoremediation of wastewater is genetic modification. A comprehensive description of using genetically engineered microalgae for wastewater bioremediation is discussed in this review. This article also reviews random and targeted mutations as a method to alter microalgal traits to produce strains capable of tolerating various stressors related to wastewater. Other methods of genetic engineering are discussed, with sympathy for CRISPR/Cas9 technology. This is accompanied by the opportunities, as well as the challenges of using genetically engineered microalgae for this purpose.

Exploring the Physiological Multiplicity of Native Microalgae from the Ecuadorian Highland, Italian Lowland and Indoor Locations in Response to UV-B

The differential effects of UV-B on the inhibition or activation of protective mechanisms to maintain cells photosynthetically active were investigated in native microalgae. Four strains were used, including two Chlorella sorokiniana strains, F4 and LG1, isolated from a Mediterranean inland swamp and a recycled cigarette butt's substrate, respectively, and two isolates from an Ecuadorian highland lake related to Pectinodesmus pectinatus (PEC) and Ettlia pseudoalveolaris (ETI). Monocultures were exposed to acute UV-B (1.7 W m^-2) over 18 h under controlled conditions. UV-B-untreated microalgae were used as the control. Comparative physiological responses, including photosynthetic pigments, non-enzymatic antioxidants, and chlorophyll a fluorescence, were evaluated at specific time points. Results showed that UV-B significantly compromised all the physiological parameters in F4, thereby resulting in the most UV-B-sensitive strain. Contrarily, UV-B exposure did not lead to changes in the PEC physiological traits, resulting in the best UV-B-resistant strain. This could be attributed to the acclimation to high light habitat, where maintaining a constitutive phenotype (at the photosynthetic level) is strategically advantageous. Differently, LG1 and ETI at 12 h of UV-B exposure showed different UV-B responses, which is probably related to acclimation, where in LG1, the pigments were recovered, and the antioxidants were still functioning, while in ETI, the accumulation of pigments and antioxidants was increased to avoid further photodamage. Consequently, the prolonged exposure in LG1 and ETI resulted in species-specific metabolic regulation (e.g., non-enzymatic antioxidants) in order to constrain full photoinhibition under acute UV-B.

Combined effect of nitrogen and phosphorus on growth and biochemical composition of Tetradesmus obliquus (Turpin) M.J. Wynne

Microalgae have many biotechnological applications in various industries including food and feed, fertilizer, biofuel, cosmetics, pharmaceutics, and wastewater treatment. Since hey produce secondary metabolites under stress conditions such as pigments, carotenoids, hydrocarbons, and vitamins, investigating the effects of stress factors on growth parameters and biochemical composition of microalgal biomass is needed in producing bioproducts. In this paper, the combined effects of nitrogen and phosphorus on growth and the protein/amino acid and Lipid-FAMEs profiles of microalgae Tetradesmus obliquus (MAKUMACC-037) were investigated. Nitrogen and phosphorus deficiency reduced the algal growth. Biochemical composition was changed in a nitrogen and phosphorus dependent manner. High concentration of protein and lipid were associated with increased nitrogen and phosphorus concentration However, the FAMEs profiles were changed depending on only the nitrogen concentration.

Role of regulatory pathways and multi-omics approaches for carbon capture and mitigation in cyanobacteria

Cyanobacteria are known for their metabolic potential and carbon capture and sequestration capabilities. These cyanobacteria are not only an effective source for carbon minimization and resource mobilization into value-added products for biotechnological gains. The present review focuses on the detailed description of carbon capture mechanisms exerted by the various cyanobacterial strains, the role of important regulatory pathways, and their subsequent genes responsible for such mechanisms. Moreover, this review will also describe effectual mechanisms of central carbon metabolism like isoprene synthesis, ethylene production, MEP pathway, and the role of Glyoxylate shunt in the carbon sequestration mechanisms. This review also describes some interesting facets of using carbon assimilation mechanisms for valuable bio-products. The role of regulatory pathways and multi-omics approaches in cyanobacteria will not only be crucial towards improving carbon utilization but also will give new insights into utilizing cyanobacterial bioresource for carbon neutrality.

Emerging Technologies for Enhancing Microalgae Biofuel Production: Recent Progress, Barriers, and Limitations

The world has heavily relied on fossil fuels for decades to supply energy demands. However, the usage of fossil fuels has been strongly correlated with impactful problems, which lead to global warming. Moreover, the excessive use of fossil fuels has led to their rapid depletion. Hence, exploring other renewable and sustainable alternatives to fossil fuels is imperative. One of the most sustainable fossil fuel alternatives is biofuel. Microalgae-based biofuels are receiving the attention of researchers due to their numerous advantages compared with those obtained from other types of feedstocks. Hence, it is essential to explore the recent technologies for biofuel produced from microalgae species and define the possible challenges that might be faced during this process. Therefore, this work presents the recent advancements in biofuel production from microalgae, focusing on emerging technologies such as those using nanomaterials and genetic engineering. This review focuses on the impact of nanoparticles on the harvesting efficiency of various microalgae species and the influence of nanoparticles on biofuel production. The genetic screening performed by genome-scale mutant libraries and their high-throughput screening may assist in developing effective strategies for enhancing microalgal strains and oil production through the modification of enzymes. Furthermore, the barriers that limit the production of biofuels from microalgae are introduced. Even though microalgae-based biofuels are perceived to engage with low negative impacts on the environment, this review paper touches on several environmental issues associated with the cultivation and harvesting of microalgae species. Moreover, the economic and technical feasibility limits the production of microalgae-based biofuels.

Recent advances in the bio-application of microalgae-derived biochemical metabolites and development trends of photobioreactor-based culture systems

Microalgae are microscopic algae in sizes ranging from a few micrometers to several hundred micrometers. On average, half of the oxygen in the atmosphere is produced by the photosynthetic process of microalgae, so the role of these microorganisms in the life cycle of the planet is very significant. Pharmaceutical products derived from microalgae and commercial developments of a variety of supplements extracted from them originate from a variety of their specific secondary metabolites. Many of these microalgae are a reservoir of unique biological compounds including carotenoids, antioxidants, fatty acids, polysaccharides, enzymes, polymers, peptides, pigments, toxins and sterols with antimicrobial, antiviral, antifungal, antiparasitic, anticoagulant, and anticancer properties. The present work begins with an introduction of the importance of microalgae in renewable fuels and biodiesel production, the development of healthy food industry, and the creation of optimal conditions for efficient biomass yield. This paper provides the latest research related to microalgae-derived substances in the field of improving drug delivery, immunomodulatory, and anticancer attributes. Also, the latest advances in algal biocompounds to combat the COVID-19 pandemic are presented. In the subject of cultivation and growth of microalgae, the characteristics of different types of photobioreactors, especially their latest forms, are fully discussed along with their advantages and obstacles. Finally, the potential of microalgae biomass in biotechnological applications, biofuel production, as well as various biomass harvesting methods are described.

Fluorescent Imaging and Sorting of High-Lipid-Content Strains of Green Algae by Using an Aggregation-Induced Emission Luminogen

Microalgae-based biofuels are receiving attention at the environmental, economic, and social levels because they are clean, renewable, and quickly produced. The green algae Chlorella vulgaris has been extensively studied in research laboratories and the biofuel industry as a model organism to increase lipid production to be cost-effective in commercial production. In this work, we utilized a lipid-droplet-specific luminogen with aggregation-induced emission (AIE) characteristics to increase the lipid production of C. vulgaris by fluorescent imaging and sorting of those algal cells with large and rich lipid droplets for subculturing. The AIE-active TPA-A enabled real-time monitoring of the size and number of lipid droplets in C. vulgaris during their growth period so that we can identify the best time for harvesting. Furthermore, the algae cells with high lipid content were identified and collected for subculturing by the technique of fluorescence-activated cell sorting (FACS). The lipid production in the generation of two successive selections was almost doubled compared to the generation with natural selection. This work demonstrated that the technologies of AIE and FACS could be applied together to improve the production of a third-generation biofuel.

Chlamydomonas reinhardtii Alternates Peroxisomal Contents in Response to Trophic Conditions

Chlamydomonas reinhardtii is a model green microalga capable of heterotrophic growth on acetic acid but not fatty acids, despite containing a full complement of genes for β-oxidation. Recent reports indicate that the alga preferentially sequesters, rather than breaks down, lipid acyl chains as a means to rebuild its membranes rapidly. Here, we assemble a list of potential Chlamydomonas peroxins (PEXs) required for peroxisomal biogenesis to suggest that C. reinhardtii has a complete set of peroxisome biogenesis factors. To determine involvements of the peroxisomes in the metabolism of exogenously added fatty acids, we examined transgenic C. reinhardtii expressing fluorescent proteins fused to N- or C-terminal peptide of peroxisomal proteins, concomitantly with fluorescently labeled palmitic acid under different trophic conditions. We used confocal microscopy to track the populations of the peroxisomes in illuminated and dark conditions, with and without acetic acid as a carbon source. In the cells, four major populations of compartments were identified, containing: (1) a glyoxylate cycle enzyme marker and a protein containing peroxisomal targeting signal 1 (PTS1) tripeptide but lacking the fatty acid marker, (2) the fatty acid marker alone, (3) the glyoxylate cycle enzyme marker alone, and (4) the PTS1 marker alone. Less than 5% of the compartments contained both fatty acid and peroxisomal markers. Statistical analysis on optically sectioned images found that C. reinhardtii simultaneously carries diverse populations of the peroxisomes in the cell and modulates peroxisomal contents based on light conditions. On the other hand, the ratio of the compartment containing both fatty acid and peroxisomal markers did not change significantly regardless of the culture conditions. The result indicates that β-oxidation may be only a minor occurrence in the peroxisomal population in C. reinhardtii, which supports the idea that lipid biosynthesis and not β-oxidation is the primary metabolic preference of fatty acids in the alga.

The chloroplast genome of Salix floderusii and characterization of chloroplast regulatory elements

Salix floderusii is a rare alpine tree species in the Salix genus. Unfortunately, no extensive germplasm identification, molecular phylogeny, and chloroplast genomics of this plant have been conducted. We sequenced the chloroplast (cp) genome of S. floderusii for the first time using second-generation sequencing technology. The cp genome was 155,540 bp long, including a large single-copy region (LSC, 84,401 bp), a small single-copy region (SSC, 16,221 bp), and inverted repeat regions (IR, 54,918 bp). A total of 131 genes were identified, including 86 protein genes, 37 tRNA genes, and 8 rRNA genes. The S. floderusii cp genome contains 1 complement repeat, 24 forward repeats, 17 palindromic repeats, and 7 reverse repeats. Analysis of the IR borders showed that the IRa and IRb regions of S. floderusii and Salix caprea were shorter than those of Salix cinerea, which may affect plastome evolution. Furthermore, four highly variable regions were found, including the rpl22 coding region, psbM/trnD-GUC non-coding region, petA/psbJ non-coding region, and ycf1 coding region. These high variable regions can be used as candidate molecular markers and as a reference for identifying future Salix species. In addition, phylogenetic analysis indicated that the cp genome of S. floderusii is sister to Salix cupularis and belongs to the Subgenus Vetrix. Genes (Sf-trnI, Sf-PpsbA, aadA, Sf-TpsbA, Sf-trnA) obtained via cloning were inserted into the pBluescript II SK (+) to yield the cp expression vectors, which harbored the selectable marker gene aadA. The results of a spectinomycin resistance test indicated that the cp expression vector had been successfully constructed. Moreover, the aadA gene was efficiently expressed under the regulation of predicted regulatory elements. The present study provides a solid foundation for establishing subsequent S. floderusii cp transformation systems and developing strategies for the genetic improvement of S. floderusii.

Microalgae-bacterial granular consortium: Striding towards sustainable production of biohydrogen coupled with wastewater treatment

Anthropogenic activities have drastically affected the environment, leading to increased waste accumulation in atmospheric bodies, including water. Wastewater treatment is an energy-consuming process and typically requires thousands of kilowatt hours of energy. This enormous energy demand can be fulfilled by utilizing the microbial electrolysis route to breakdown organic pollutants in wastewater which produces clean water and biohydrogen as a by-product of the reaction. Microalgae are the promising microorganism for the biohydrogen production, and it has been investigated that the interaction between microalgae and bacteria can be used to boost the yield of biohydrogen. Consortium of algae and bacteria resulting around 50-60% more biohydrogen production compared to the biohydrogen production of algae and bacteria separately. This review summarises the recent development in different microalgae-bacteria granular consortium systems successfully employed for biohydrogen generation. We also discuss the limitations in biohydrogen production and factors affecting its production from wastewater.

Emerging Trends in Genetic Engineering of Microalgae for Commercial Applications

Recently, microalgal biotechnology has received increasing interests in producing valuable, sustainable and environmentally friendly bioproducts. The development of economically viable production processes entails resolving certain limitations of microalgal biotechnology, and fast evolving genetic engineering technologies have emerged as new tools to overcome these limitations. This review provides a synopsis of recent progress, current trends and emerging approaches of genetic engineering of microalgae for commercial applications, including production of pharmaceutical protein, lipid, carotenoids and biohydrogen, etc. Photochemistry improvement in microalgae and CO2 sequestration by microalgae via genetic engineering were also discussed since these subjects are closely entangled with commercial production of the above mentioned products. Although genetic engineering of microalgae is proved to be very effective in boosting performance of production in laboratory conditions, only limited success was achieved to be applicable to industry so far. With genetic engineering technologies advancing rapidly and intensive investigations going on, more bioproducts are expected to be produced by genetically modified microalgae and even much more to be prospected.

Application of Pulsed Electric Fields and High-Pressure Homogenization in Biorefinery Cascade of C. vulgaris Microalgae

In this study, a cascaded cell disintegration process, based on pulsed electric fields (PEF - 20 kV/cm, 100 kJ/kg_SUSP.) and high-pressure homogenization (HPH - 150 MPa, 5 passes) was designed for the efficient and selective release of intracellular compounds (water-soluble proteins, carbohydrates, and lipids) from C. vulgaris suspensions during extraction in water (25 °C, 1 h) and ethyl acetate (25 °C, 3 h). Recovery yields of target compounds from cascaded treatments (PEF + HPH) were compared with those observed when applying PEF and HPH treatments individually. Particle size distribution and scanning electron microscopy analyses showed that PEF treatment alone did not induce any measurable effect on cell shape/structure, whereas HPH caused complete cell fragmentation and debris formation, with an undifferentiated release of intracellular matter. Spectra measurements demonstrated that, in comparison with HPH alone, cascaded treatments increased the selectivity of extraction and improved the yields of carbohydrates and lipids, while higher yields of water-soluble proteins were measured for HPH alone. This work, therefore, demonstrates the feasibility of sequentially applying PEF and HPH treatments in the biorefinery of microalgae, projecting a beneficial impact in terms of process economics due to the potential reduction of the energy requirements for separation/purification stages.

Microalgal metabolic engineering strategies for the production of fuels and chemicals

Microalgae are promising sustainable resources because of their ability to convert CO₂ into biofuels and chemicals directly. However, the industrial production and economic feasibility of microalgal bioproducts are still limited. As such, metabolic engineering approaches have been undertaken to enhance the productivities of microalgal bioproducts. In the last decade, impressive advances in microalgae metabolic engineering have been made by developing genetic engineering tools and multi-omics analysis. This review presents comprehensive microalgal metabolic pathways and metabolic engineering strategies for producing lipids, long chain-polyunsaturated fatty acids, terpenoids, and carotenoids. Additionally, promising metabolic engineering approaches specific to target products are summarized. Finally, this review discusses current challenges and provides future perspectives for the effective production of chemicals and fuels via microalgal metabolic engineering.

High-throughput selection of cells based on accumulated growth and division using PicoShell particles

Production of high-energy lipids by microalgae may provide a sustainable energy source that can help tackle climate change. However, microalgae engineered to produce more lipids usually grow slowly, leading to reduced overall yields. Unfortunately, culture vessels used to select cells based on growth while maintaining high biomass production, such as well plates, water-in-oil droplet emulsions, and nanowell arrays, do not provide production-relevant environments that cells experience in scaled-up cultures (e.g., bioreactors or outdoor cultivation farms). As a result, strains that are developed in the laboratory may not exhibit the same beneficial phenotypic behavior when transferred to industrial production. Here, we introduce PicoShells, picoliter-scale porous hydrogel compartments, that enable >100,000 individual cells to be compartmentalized, cultured in production-relevant environments, and selected based on growth and bioproduct accumulation traits using standard flow cytometers. PicoShells consist of a hollow inner cavity where cells are encapsulated and a porous outer shell that allows for continuous solution exchange with the external environment. PicoShells allow for cell growth directly in culture environments, such as shaking flasks and bioreactors. We experimentally demonstrate that Chlorella sp., Saccharomyces cerevisiae, and Chinese hamster ovary cells, used for bioproduction, grow to significantly larger colony sizes in PicoShells than in water-in-oil droplet emulsions (P < 0.05). We also demonstrate that PicoShells containing faster dividing and growing Chlorella clonal colonies can be selected using a fluorescence-activated cell sorter and regrown. Using the PicoShell process, we select a Chlorella population that accumulates chlorophyll 8% faster than does an unselected population after a single selection cycle.

A Novel Bifunctional Wax Ester Synthase Involved in Early Triacylglycerol Accumulation in Unicellular Green Microalga Haematococcus pluvialis Under High Light Stress

The bulk of neutral lipids, including astaxanthin esters and triacylglycerols (TAGs), are accumulated in the green microalga Haematococcus pluvialis under high light (HL) stress. In this study, a novel bifunctional wax ester synthase (WS) gene was cloned from H. pluvialis upon HL stress. The overexpression of HpWS restored the biosynthesis of wax esters and TAGs in neutral lipid-deficient yeast mutant Saccharomyces cerevisiae H1246 fed with C18 alcohol and C18:1/C18:3 fatty acids, respectively. Under HL stress, HpWS was substantially upregulated at the transcript level, prior to that of the type I diacylglycerol:acyl-CoA acyltransferase encoding gene (HpDGAT1). HpDGAT1 is the major TAG synthase in H. pluvialis. In addition, the application of xanthohumol (a DGAT1/2 inhibitor) in the H. pluvialis cells did not completely eliminate the TAG biosynthesis under HL stress at 24 h. These results indicated that HpWS may contribute to the accumulation of TAGs in H. pluvialis at the early stage under HL stress. In addition, the overexpression of HpWS in Chlamydomonas reinhardtii bkt5, which is engineered to produce free astaxanthin, enhanced the production of TAGs and astaxanthin. Our findings broaden the understanding of TAG biosynthesis in microalgae and provide a new molecular target for genetic manipulation in biotechnological applications.

The allelopathy and underlying mechanism of Skeletonema costatum on Karenia mikimotoi integrating transcriptomics profiling

The roles of allelopathy for succession of marine phytoplankton communities remain controversial, especially for the development of blooms. Physiological parameters measurement (Fv/Fm value, MDA content, SOD activity, Na⁺/K⁺, Ca²⁺/ Mg²⁺-ATPase activity, cell size, chlorophyll content, apoptosis and cell cycle) and whole transcriptome profiling analysis were used to investigate allelopathy effect of Skeletonema costatum on Karenia mikimotoi. Filtrate and extracts from S. costatum culture inhibited the growth of K. mikimotoi. Allelopathic effects were dose-dependent for filtrate culture and extract culture. K. mikimotoi scavenged excessive ROS and adapted to the stress fastly and easily, so oxidative damage was not the main cause of the growth inhibition. Allelochemicals of S. costatum were found to influence the structure and function of cell membrane of K. mikimotoi by damaging membrane structure till to cell necrosis, which caused high mortality. Coupled with the sensitivity of algal cells to environmental stress and restricted cell cycle, allelopathy was suggested to be deeply detrimental to the development of competition algal population.

Sustainable valorization of algae biomass via thermochemical processing route: An overview

Biofuels have become an attractive energy source because of the growing energy demand and environmental issues faced by fossil fuel consumption. Algal biomass, particularly microalgae, has excellent potential as feedstock to be converted to bio-oil, biochar, and combustible syngas via thermochemical conversion processes. Third-generation biofuels from microalgal feedstock are the promising option, followed by the first-generation and second-generation biofuels. This paper provides a review of the applications of thermochemical conversion techniques for biofuel production from algal biomass, comprising pyrolysis, gasification, liquefaction, and combustion processes. The progress in the thermochemical conversion of algal biomass is summarized, emphasizing the application of pyrolysis for its benefits over other processes. The review also encompasses the challenges and perspectives associated with the valorization of microalgae to biofuels ascertaining the potential opportunities and possibilities of extending the research into this area.

Microalgae-based carbohydrates: A green innovative source of bioenergy

Microalgae contribute significantly to the global carbon cycle through photosynthesis. Given their ability to efficiently convert solar energy and atmospheric carbon dioxide into chemical compounds, such as carbohydrates, and generate oxygen during the process, microalgae represent an excellent and feasible carbohydrate bioresource. Microalgae-based biofuels are technically viable and, delineate a green and innovative field of opportunity for bioenergy exploitation. Microalgal polysaccharides are one of the most versatile groups for biotechnological applications and its content can be increased by manipulating cultivation conditions. Microalgal carbohydrates can be used to produce a variety of biofuels, including bioethanol, biobutanol, biomethane, and biohydrogen. This review provides an overview of microalgal carbohydrates, focusing on their use as feedstock for biofuel production, highlighting the carbohydrate metabolism and approaches for their enhancement. Moreover, biofuels produced from microalgal carbohydrate are showed, in addition to a new bibliometric study of current literature on microalgal carbohydrates and their use.

Solid-State NMR Investigations of Extracellular Matrixes and Cell Walls of Algae, Bacteria, Fungi, and Plants

Extracellular matrixes (ECMs), such as the cell walls and biofilms, are important for supporting cell integrity and function and regulating intercellular communication. These biomaterials are also of significant interest to the production of biofuels and the development of antimicrobial treatment. Solid-state nuclear magnetic resonance (ssNMR) and magic-angle spinning-dynamic nuclear polarization (MAS-DNP) are uniquely powerful for understanding the conformational structure, dynamical characteristics, and supramolecular assemblies of carbohydrates and other biomolecules in ECMs. This review highlights the recent high-resolution investigations of intact ECMs and native cells in many organisms spanning across plants, bacteria, fungi, and algae. We spotlight the structural principles identified in ECMs, discuss the current technical limitation and underexplored biochemical topics, and point out the promising opportunities enabled by the recent advances of the rapidly evolving ssNMR technology.

Ectopic expression of bacterial 1-aminocyclopropane 1-carboxylate deaminase in Chlamydomonas reinhardtii enhances algal biomass and lipid content under nitrogen deficit condition

1-Aminocyclopropane-1-carboxylate (ACC) deaminase is a well-known bacterial producing enzyme that helps plants to overcome stress conditions by modulating ethylene biosynthesis. However, the functional role of ACC deaminase and ethylene in microalgae during stress remains to be explored. In this study, to investigate the role of ACC deaminase (acds) from Pseudomonas putida UW4 in enhancing the biomass and lipid content of Chlamydomonas under nitrogen deficit condition. The synthetic codon-optimized acds gene was cloned into vector pChlamy_4 and introduced into Chlamydomonas. Results indicated that Chlamydomonas-expressing acds lines showed significant tolerance to nitrogen-deficit by reducing the ethylene content. The biomass, chlorophyll content and photosynthetic activity of acds-expressing lines were significantly increased during nitrogen deficit condition. Moreover, the intracellular lipid and fatty acid content were much higher in acds-expressing lines than the wild-type. In terms of stress alleviation, the transgenic lines displayed increased antioxidant enzymes, reduced ROS and lipid peroxidation levels.

Complete Chloroplast Genome Sequence of Erigeron breviscapus and Characterization of Chloroplast Regulatory Elements

Erigeron breviscapus is a famous medicinal plant. However, the limited chloroplast genome information of E. breviscapus, especially for the chloroplast DNA sequence resources, has hindered the study of E. breviscapus chloroplast genome transformation. Here, the complete chloroplast (cp) genome of E. breviscapus was reported. This genome was 152,164bp in length, included 37.2% GC content and was structurally arranged into two 24,699bp inverted repeats (IRs) and two single-copy areas. The sizes of the large single-copy region and the small single-copy region were 84,657 and 18,109bp, respectively. The E. breviscapus cp genome consisted of 127 coding genes, including 83 protein coding genes, 36 transfer RNA (tRNA) genes, and eight ribosomal RNA (rRNA) genes. For those genes, 95 genes were single copy genes and 16 genes were duplicated in two inverted regions with seven tRNAs, four rRNAs, and five protein coding genes. Then, genomic DNA of E. breviscapus was used as a template, and the endogenous 5' and 3' flanking sequences of the trnI gene and trnA gene were selected as homologous recombinant fragments in vector construction and cloned through PCR. The endogenous 5' flanking sequences of the psbA gene and rrn16S gene, the endogenous 3' flanking sequences of the psbA gene, rbcL gene, and rps16 gene and one sequence element from the psbN-psbH chloroplast operon were cloned, and certain chloroplast regulatory elements were identified. Two homologous recombination fragments and all of these elements were constructed into the cloning vector pBluescript SK (+) to yield a series of chloroplast expression vectors, which harbored the reporter gene EGFP and the selectable marker aadA gene. After identification, the chloroplast expression vectors were transformed into Escherichia coli and the function of predicted regulatory elements was confirmed by a spectinomycin resistance test and fluorescence intensity measurement. The results indicated that aadA gene and EGFP gene were efficiently expressed under the regulation of predicted regulatory elements and the chloroplast expression vector had been successfully constructed, thereby providing a solid foundation for establishing subsequent E. breviscapus chloroplast transformation system and genetic improvement of E. breviscapus.

Microalgae as a Source of Mycosporine-like Amino Acids (MAAs); Advances and Future Prospects

Mycosporine-like amino acids (MAAs), are secondary metabolites, first reported in 1960 and found to be associated with the light-stimulated sporulation in terrestrial fungi. MAAs are nitrogenous, low molecular weight, water soluble compounds, which are highly stable with cyclohexenone or cycloheximine rings to store the free radicals. Microalgae are considered as a good source of different kinds of MAAs, which in turn, has its own applications in various industries due to its UV absorbing, anti-oxidant and therapeutic properties. Microalgae can be easily cultivated and requires a very short generation time, which makes them environment friendly source of biomolecules such as mycosporine-like amino acids. Modifying the cultural conditions along withmanipulation of genes associated with mycosporine-like amino acids biosynthesis can help to enhance MAAs synthesis and, in turn, can make microalgae suitable bio-refinery for large scale MAAs production. This review focuses on properties and therapeutic applications of mycosporine like amino acids derived from microalgae. Further attention is drawn on various culture and genetic engineering approaches to enhance the MAAs production in microalgae.

Genetic engineering of microalgae for enhanced lipid production

Microalgae have the potential to become microbial cell factories for lipid production. Their ability to convert sunlight and CO₂ into valuable lipid compounds has attracted interest from cosmetic, biofuel, food and feed industries. In order to make microalgae-derived products cost-effective and commercially competitive, enhanced growth rates and lipid productivities are needed, which require optimization of cultivation systems and strain improvement. Advances in genetic tool development and omics technologies have increased our understanding of lipid metabolism, which has opened up possibilities for targeted metabolic engineering. In this review we provide a comprehensive overview on the developments made to genetically engineer microalgal strains over the last 30 years. We focus on the strategies that lead to an increased lipid content and altered fatty acid profile. These include the genetic engineering of the fatty acid synthesis pathway, Kennedy pathway, polyunsaturated fatty acid and triacylglycerol metabolisms and fatty acid catabolism. Moreover, genetic engineering of specific transcription factors, NADPH generation and central carbon metabolism, which lead to increase of lipid accumulation are also reviewed.

Monodopsis and Vischeria Genomes Shed New Light on the Biology of Eustigmatophyte Algae

Members of eustigmatophyte algae, especially Nannochloropsis and Microchloropsis, have been tapped for biofuel production owing to their exceptionally high lipid content. Although extensive genomic, transcriptomic, and synthetic biology toolkits have been made available for Nannochloropsis and Microchloropsis, very little is known about other eustigmatophytes. Here we present three near-chromosomal and gapless genome assemblies of Monodopsis strains C73 and C141 (60 Mb) and Vischeria strain C74 (106 Mb), which are the sister groups to Nannochloropsis and Microchloropsis in the order Eustigmatales. These genomes contain unusually high percentages of simple repeats, ranging from 12% to 21% of the total assembly size. Unlike Nannochloropsis and Microchloropsis, long interspersed nuclear element repeats are abundant in Monodopsis and Vischeria and might constitute the centromeric regions. We found that both mevalonate and nonmevalonate pathways for terpenoid biosynthesis are present in Monodopsis and Vischeria, which is different from Nannochloropsis and Microchloropsis that have only the latter. Our analysis further revealed extensive spliced leader trans-splicing in Monodopsis and Vischeria at 36-61% of genes. Altogether, the high-quality genomes of Monodopsis and Vischeria not only serve as the much-needed outgroups to advance Nannochloropsis and Microchloropsis research, but also shed new light on the biology and evolution of eustigmatophyte algae.

Microalgae for high-value products: A way towards green nutraceutical and pharmaceutical compounds

Microalgae is a renewable bioresource with the potential to replace the conventional fossil-based industrial production of organic chemicals and pharmaceuticals. Moreover, the microalgal biomass contains carotenoids, vitamins, and other biomolecules that are widely used as food supplements. However, the microalgal biomass production, their composition variations, energy-intensive harvesting methods, optimized bio-refinery routes, and lack of techno-economic analysis are the major bottleneck for the life-sized commercialization of this nascent bio-industry. This review discusses the microalgae-derived key bioactive compounds and their applications in different sectors for human health. Furthermore, this review proposes advanced strategies to enhance the productivity of bioactive compounds and highlight the key challenges associated with a safety issue for use of microalgae biomass. It also provides a detailed global scenario and market demand of microalgal bioproducts. In conclusion, this review will provide the concept of microalgal biorefinery to produce bioactive compounds at industrial scale platform for their application in the nutraceutical and pharmaceutical sector considering their current and future market trends.

Biotechnology for carbon capture and fixation: Critical review and future directions

To mitigate the growing threat of climate change and develop novel technologies that can eliminate carbon dioxide, the most abundant greenhouse gas derived from the flue gas stream of the fossil fuel-fired power stations, is momentous. The development of carbon capture and sequestration-based technologies may play a significant role in this regard. Carbon fixation mostly occurs by photosynthesizing plants as well as photo and chemoautotrophic microbes that turn the atmospheric carbon dioxide into organic materials via their enzymes. Biofuel can offer a sustainable solution for carbon mitigation. The pragmatic implementation of biofuel production processes is neither cost-effective nor has been proven safe over the long term. Searching for ways to enhance biofuel generation by the employment of genetic engineering is vital. Carbon biosequestration can help to curb the greenhouse effect. In addition, new genomic approaches, which are able to use gene-splicing biotechnology techniques and recombinant DNA technology to produce genetically modified organisms, can contribute to improvement in sustainable and renewable biofuel and biomaterial production from microorganisms. Biopolymers, Biosurfactants, and Biochars are suggested as sustainable future trends. This study aims to pave the way for implementing biotechnology methods to capture carbon and decrease the demand and consumption of fossil fuels as well as the emissions of greenhouse gases. Having a better image of microorganisms' potential role in carbon capture and storage can be prolific in developing powerful techniques to reduce CO₂ emissions.

Microalgal Production of Biofuels Integrated with Wastewater Treatment

Human civilization will need to reduce its impacts on air and water quality and reduce its use of fossil fuels in order to advance towards a more sustainable future. Using microalgae to treat wastewater as well as simultaneously produce biofuels is one of the approaches for a sustainable future. The manufacture of biofuels from microalgae is one of the next-generation biofuel solutions that has recently received a lot of interest, as it can remove nutrients from the wastewater whilst capturing carbon dioxide from the atmosphere. The resulting biomass are employed to generate biofuels, which can run fuel cell vehicles of zero emission, power combustion engines and power plants. By cultivating microalgae in wastewater, eutrophication can be prevented, thereby enhancing the quality of the effluent. Thus, by combining wastewater treatment and biofuel production, the cost of the biofuels, as well as the environmental hazards, can be minimized, as there is a supply of free and already available nutrients and water. In this article, the steps involved to generate the various biofuels through microalgae are detailed.

The biosynthesis of phospholipids is linked to the cell cycle in a model eukaryote

The structural challenges faced by eukaryotic cells through the cell cycle are key for understanding cell viability and proliferation. We tested the hypothesis that the biosynthesis of structural lipids is linked to the cell cycle. If true, this would suggest that the cell's structure is important for progress through and perhaps even control of the cell cycle. Lipidomics (31P NMR and MS), proteomics (Western immunoblotting) and transcriptomics (RT-qPCR) techniques were used to profile the lipid fraction and characterise aspects of its metabolism at seven stages of the cell cycle of the model eukaryote, Desmodesmus quadricauda. We found considerable, transient increases in the abundance of phosphatidylethanolamine during the G1 phase (+35%, ethanolamine phosphate cytidylyltransferase increased 2·5×) and phosphatidylglycerol (+100%, phosphatidylglycerol synthase increased 22×) over the G1/pre-replication phase boundary. The relative abundance of phosphatidylcholine fell by ~35% during the G1. N-Methyl transferases for the conversion of phosphatidylethanolamine into phosphatidylcholine were not found in the de novo transcriptome profile, though a choline phosphate transferase was found, suggesting that the Kennedy pathway is the principal route for the synthesis of PC. The fatty acid profiles of the four most abundant lipids suggested that these lipids were not generally converted between one another. This study shows for the first time that there are considerable changes in the biosynthesis of the three most abundant phospholipid classes in the normal cell cycle of D. quadricauda, by margins large enough to elicit changes to the physical properties of membranes.

Simultaneous knockout of multiple LHCF genes using single sgRNAs and engineering of a high-fidelity Cas9 for precise genome editing in marine algae

The CRISPR/Cas9 system is an RNA-guided sequence-specific genome editing tool, which has been adopted for single or multiple gene editing in a wide range of organisms. When working with gene families with functional redundancy, knocking out multiple genes within the same family may be required to generate a phenotype. In this study, we tested the possibility of exploiting the known tolerance of Cas9 for mismatches between the single-guide RNA (sgRNA) and target site to simultaneously introduce indels in multiple homologous genes in the marine diatom Phaeodactylum tricornutum. As a proof of concept, we designed two sgRNAs that could potentially target the same six light-harvesting complex (LHC) genes belonging to the LHCF subgroup. Mutations in up to five genes were achieved simultaneously using a previously established CRISPR/Cas9 system for P. tricornutum. A visible colour change was observed in knockout mutants with multiple LHCF lesions. A combination of pigment, LHCF protein and growth analyses was used to further investigate the phenotypic differences between the multiple LHCF mutants and WT. Furthermore, we used the two same sgRNAs in combination with a variant of the existing Cas9 where four amino acids substitutions had been introduced that previously have been shown to increase Cas9 specificity. A significant reduction of off-target editing events was observed, indicating that the altered Cas9 functioned as a high-fidelity (HiFi) Cas9 nuclease.