Polymer Selection for Hot-Melt Extrusion Coupled to Fused Deposition Modelling in Pharmaceutics

Hot-melt extruded-FDM 3D-printed polyethylene oxide tablets: Dissolution imaging analysis of swelling and drug release

Recent developments in pharmacogenetics have emphasised the importance of customised medication, driving interest in technologies like FDM 3D-printing for tailored drug delivery. FDM 3D-printing is a promising technique for the on-demand manufacturing of customised oral dosage forms, providing flexibility in terms of shape and size, dose and drug release profiles. This study investigates the fabrication and characterisation of 3D-printed oral dosage forms using PEO as the primary polymer and PEG 6 K as a plasticiser. Firstly, the printability of the PEO filaments with different propranolol hydrochloride concentrations was explored using the hot-melt extrusion technology. The influence of the propranolol hydrochloride concentrations on the mechanical properties of the filaments was examined was then examined after which surface characteristics, including roughness and wettability, were evaluated. Dissolution imaging was used to visualise the effects of drug content on the swelling and dissolution characteristics of the PEO-based 3D-printed tablets. Results showed a reduction in the flexural stress of the filaments with increasing drug load. It was also observed that increasing the drug load led to higher surface roughness and lower contact angles of the 3D-printed PEO tablets, implying increased surface hydrophilicity. The swelling behaviour of the tablets increased with higher drug concentrations, resulting in a larger gel layer formation. When comparing the drug release percentages, the release rate was higher in the 10 mg propranolol tablets, suggesting that a lower drug content led to a faster release. The greater gel layer of the 40 mg PPN tablets hindered the drug release by acting as a diffusion barrier, while the 10 mg PPN tablets, with less swelling and gel formation, experienced a faster drug release. These findings show the importance of drug content in modifying the surface properties, swelling behaviour, and drug release profiles of 3D-printed PEO tablets. The study also demonstrates the novel use of dissolution imaging for 3D-printed dosage forms, providing valuable quantitative and qualitative insights into swelling dynamics and channel formation to optimise 3D-printed tablets for drug delivery systems.

Selective laser sintering for printing bilayer tablets

In this study Selective Laser Sintering (SLS) was used to produce bilayer tablets containing rosuvastatin and acetylsalicylic acid. Initially, monolithic tablets of each drug were manufactured using different laser intensities in order to identify their impact on the tablet's dissolution, friability and hardness. After the optimization, the final bilayer tablet was fabricated using a new method, that allowed the printing using different powder blends. For that, a 3D-printed casing was employed to maintain the compartments of the tablet in the correct position during the printing process. The results demonstrated that the increased laser intensities led to denser inner cores, enhanced hardness, decreased friability, and slower drug release. Moreover, the new method was able to produce bilayer tablets completely aligned, showing a minor impact on dissolution when the two compartments were printed together in a single tablet. The work demonstrated the feasibility of using SLS in the production of multi-material drug delivery systems.

Exploring the impact of material selection on the efficacy of hot-melt extrusion

Hot-melt extrusion (HME) has emerged as a versatile and efficient technique in pharmaceutical formulation development, particularly for enhancing the solubility and bioavailability of poorly water-soluble drugs. This review delves into the fundamental principles of HME, exploring its application in drug delivery systems. A comprehensive analysis of polymers utilized in HME, such as hydroxypropyl methylcellulose, ethyl cellulose, hydroxypropyl cellulose, and polyvinylpyrrolidone, is presented, highlighting their roles in achieving controlled drug release and improved stability. The incorporation of plasticizers, such as triacetin, poly(propylene glycol), glycerol, and sorbitol, is critical in reducing the glass transition temperature (Tg) of polymer blends, thereby enhancing the processability of HME formulations. A comparison of Tg values for various polymer-plasticizer combinations is discussed using different predictive models. For researchers and industry professionals looking to optimize drug formulation strategies, this article offers valuable insights into the mechanisms through which HME enhances drug solubility and bioavailability two critical factors in oral drug delivery. Furthermore, by reviewing recent patents and marketed formulations, the article serves as a comprehensive resource for understanding both the technical advancements and commercial applications of HME. Readers will gain a deep understanding of the role of polymers and additives in HME, alongside future perspectives on how emerging materials and techniques could further revolutionize pharmaceutical development. This review is essential for those aiming to stay at the forefront of pharmaceutical extrusion technologies and their potential to improve therapeutic outcomes. The review concludes that meticulous material selection is vital for advancing pharmaceutical manufacturing processes and ensuring optimal outcomes in HME applications, thereby enhancing the overall efficacy of drug delivery systems.

Enhancing Patient-Centric Drug Development: Coupling Hot Melt Extrusion with Fused Deposition Modeling and Pressure-Assisted Microsyringe Additive Manufacturing Platforms with Quality by Design

In recent years, with the increasing patient population, the need for complex and patient-centric medications has increased enormously. Traditional manufacturing techniques such as direct blending, high shear granulation, and dry granulation can be used to develop simple solid oral medications. However, it is well known that "one size fits all" is not true for pharmaceutical medicines. Depending on the age, sex, and disease state, each patient might need a different dose, combination of medicines, and drug release pattern from the medications. By employing traditional practices, developing patient-centric medications remains challenging and unaddressed. Over the last few years, much research has been conducted exploring various additive manufacturing techniques for developing on-demand, complex, and patient-centric medications. Among all the techniques, nozzle-based additive manufacturing platforms such as pressure-assisted microsyringe (PAM) and fused deposition modeling (FDM) have been investigated thoroughly to develop various medications. Both nozzle-based techniques involve the application of thermal energy. However, PAM can also be operated under ambient conditions to process semi-solid materials. Nozzle-based techniques can also be paired with the hot melt extrusion (HME) process for establishing a continuous manufacturing platform by employing various in-line process analytical technology (PAT) tools for monitoring critical process parameters (CPPs) and critical material attributes (CMAs) for delivering safe, efficacious, and quality medications to the patient population without compromising critical quality attributes (CQAs). This review covers an in-depth discussion of various critical parameters and their influence on product quality, along with a note on the continuous manufacturing process, quality by design, and future perspectives.

Exploring 3D Printing in Drug Development: Assessing the Potential of Advanced Melt Drop Deposition Technology for Solubility Enhancement by Creation of Amorphous Solid Dispersions

Background: Melt-based 3D printing technologies are currently extensively evaluated for research purposes as well as for industrial applications. Classical approaches often require intermediates, which can pose a risk to stability and add additional complexity to the process. The Advanced Melt Drop Deposition (AMDD) technology, is a 3D printing process that combines the principles of melt extrusion with pressure-driven ejection, similar to injection molding. This method offers several advantages over traditional melt-based 3D printing techniques, making it particularly suitable for pharmaceutical applications. Objectives: This study evaluates the AMDD printing system for producing solid oral dosage forms, with a primary focus on the thermo-stable polymer polyvinyl alcohol (PVA). The suitability of AMDD technology for creating amorphous solid dispersions (ASDs) is also examined. Finally, the study aims to define the material requirements and limitations of the raw materials used in the process. Methods: The active pharmaceutical ingredients (APIs) indometacin and ketoconazole were used, with PVA 4-88 serving as the carrier polymer. Powders, wet granulates, and pellets were investigated as raw materials and characterized. Dissolution testing and content analyses were performed on the printed dosage forms. Solid-state characterization was conducted using differential scanning calorimetry (DSC) and X-ray diffraction (XRD). Degradation due to thermal and mechanical stress was analyzed using nuclear magnetic resonance spectroscopy (NMR). Results/Conclusions: The results demonstrate that the AMDD 3D printing process is well-suited for producing solid dosage forms. Tablets were successfully printed, meeting mass uniformity standards. Adjusting the infill volume from 30% to 100% effectively controlled the drug release rate of the tablets. Solid-state analysis revealed that the AMDD process can produce amorphous solid dispersions with enhanced solubility compared to their crystalline form. The experiments also demonstrated that powders with a particle size of approximately 200 µm can be directly processed using AMDD technology.

Role of rheology in formulation and process design of hot melt extruded amorphous solid dispersions

Hot melt extrusion (HME) has been widely used as a continuous and highly flexible pharmaceutical manufacturing process for the production of a variety of dosage forms. In particular, HME enables preparation of amorphous solid dispersions (ASDs) which can improve bioavailability of poorly water-soluble drugs. The rheological properties of drug-polymer mixtures can significantly influence the processability of drug formulations via HME and eventually the end-use product properties such as physical stability and drug release. The objective of this review is to provide an overview of various rheological techniques and properties that can be used to evaluate the flow behavior and processability of the drug-polymer mixtures as well as formulation characteristics such as drug-polymer interactions, miscibility/solubility, and plasticization to improve the HME processability. An overview of the thermodynamics and kinetics of ASD processing by HME is also provided, as well as aspects of scale-up and process modeling, highlighting rheological properties on formulation design and process development. Overall, this review provides valuable insights into critical rheological properties which can be used as a predictive tool to optimize the HME processing conditions.

Fabrication of Polypill Pharmaceutical Dosage Forms Using Fused Deposition Modeling 3D Printing: A Systematic Review

BACKGROUND/OBJECTIVES

The pharmacy profession has undergone significant changes driven by advancements in patient care and healthcare systems. The FDA approval of Spritam® (levetiracetam), the first 3D-printed drug, has sparked increased interest in the use of Fused Deposition Modeling (FDM) 3D printing for pharmaceutical applications, particularly in the production of polypills.

METHODS

This review provides an overview of FDM 3D printing in the development of pharmaceutical dosage forms, focusing on its operation, printing parameters, materials, additives, advantages, and limitations. Key aspects, such as the ability to personalize medication and the challenges associated with the technique, including drug stability at high temperatures, are discussed.

RESULTS

Fourteen studies relevant to FDM 3D-printed polypills were analyzed from an initial pool of 60. The increasing number of publications highlights the growing global interest in this technology, with the UK contributing the highest number of studies.

CONCLUSIONS

FDM 3D printing offers significant potential for personalized medicine by enabling precise control over dosage forms and tailoring treatments to individual patient needs. However, limitations such as high printing temperatures and the lack of standardized GMP guidelines for large-scale production must be addressed to fully realize its potential in pharmaceutical manufacturing.

Amorphous stabilization of BCS II drugs using mesoporous silica

This study aimed to investigate the amorphous stabilization of BCS Class II drugs using mesoporous silica as a carrier to produce amorphous solid dispersions. Ibuprofen, fenofibrate, and budesonide were selected as model drugs to evaluate the impact of molecular weight and partition coefficient on the solid state of drug-loaded mesoporous silica (MS) particles. The model drugs were loaded into three grades of MS, SYLYSIA SY730, SYLYSIA SY430, and SYLYSIA SY350, with pore diameters of 2.5 nm, 17 nm, and 21 nm, respectively, at 1:1, 2:1, and 3:1, carrier to drug ratios, and three different loading concentrations using solvent immersion and spray drying techniques. Differential scanning calorimetry (DSC) thermograms of SY430 and SY350 samples exhibited melting point depressions indicating constricted crystallization inside the pores, whereas SY730 samples with melting points matching the pure API may be a result of surface crystallization. Powder x-ray diffraction (PXRD) diffractograms showed all crystalline samples matched the diffraction patterns of the pure API indicating no polymorphic transitions and all 3:1 ratio samples exhibited amorphous halo profiles. Response surface regression analysis and Classification and Regression Tree (CART) analysis suggest carrier to drug ratios, followed by molecular weight, have the most significant impact on the crystallinity of a drug loaded into MS particles.

β-Lactoglobulin-based amorphous solid dispersions: A graphical review on the state-of-the-art

Proteins have recently caught attention as potential excipients for amorphous solid dispersions (ASDs) to improve oral bioavailability of poorly water-soluble drugs. Notably, the studies have highlighted whey protein isolates, particularly β-lactoglobulin (BLG), as promising candidates in amorphous stabilization, dissolution and solubility enhancement, achieving drug loadings of 50 wt% and higher. Consequently, investigations into the mechanisms underlying the solid-state stabilization of amorphous drugs and the enhancement of drug solubility in solution have been conducted. This graphical review provides a comprehensive overview of recent findings concerning BLG-based ASDs. Firstly, the dissolution performance of BLG-based ASDs is compared to more traditional polymer-based ASDs. Secondly, the drug loading onto BLG and the resulting amorphous stabilization mechanisms is summarized. Thirdly, interactions between BLG and drug molecules in solution are described as the mechanisms governing the improvement of drug solubility. Lastly, we outline the impact of the spray drying process on the secondary structure of BLG, and the resulting differences in amorphous stabilization and drug dissolution performance between α-helix-rich and β-sheet-rich BLG-based ASDs.

Specific intermolecular interaction with sodium glycocholate generates the co-amorphous system showing higher physical stability and aqueous solubility of Y5 receptor antagonist of neuropeptide Y, a brick dust molecule

Drugs with poor water and lipid solubility are termed "brick dust." We previously successfully developed a co-amorphous system of a novel neuropeptide Y5 receptor antagonist (AntiY5R), a brick dust molecule, using sodium taurocholate (NaTC) as a co-former. However, the maximum improvement in AntiY5R dissolution by the co-amorphous system was only approximately 10 times greater than that of the crystals. Therefore, in the current study, other bile salts, including sodium cholate (NaC), sodium chenodeoxycholate (NaCC), and sodium glycocholate (NaGC), were examined as co-formers to further improve AntiY5R dissolution. NaC, NaCC, and NaGC have glass transition temperatures above 150°C. All three co-amorphous systems prepared successfully retained the amorphous form of AntiY5R for 3 months at 40°C, but the co-amorphous system with NaGC (AntiY5R-NaGC; 1:9 molar ratio) provided the highest improvement in AntiY5R dissolution, which was approximately 50 times greater than that of the crystals. Possible intermolecular interactions via the glycine moiety of NaGC more than the other bile salts would contribute to the highest dissolution enhancement with AntiY5R-NaGC. Thus, NaGC would be a promising co-former for formulating stable co-amorphous systems to enhance the dissolution behavior of brick dust molecules.

Amorphous solid dispersion of a binary formulation with felodipine and HPMC for 3D printed floating tablets

This study focuses on the combination of three-dimensional printing (3DP) and amorphous solid dispersion (ASD) technologies for the manufacturing of gastroretentive floating tablets. Employing hot melt extrusion (HME) and fused deposition modeling (FDM), the study investigates the development of drug-loaded filaments and 3D printed (3DP) tablets containing felodipine as model drug and hydroxypropyl methylcellulose (HPMC) as the polymeric carrier. Prior to fabrication, solubility parameter estimation and molecular dynamics simulations were applied to predict drug-polymer interactions, which are crucial for ASD formation. Physical bulk and surface characterization complemented the quality control of both drug-loaded filaments and 3DP tablets. The analysis confirmed a successful amorphous dispersion of felodipine within the polymeric matrix. Furthermore, the low infill percentage and enclosed design of the 3DP tablet allowed for obtaining low-density systems. This structure resulted in buoyancy during the entire drug release process until a complete dissolution of the 3DP tablets (more than 8 h) was attained. The particular design made it possible for a single polymer to achieve a zero-order controlled release of the drug, which is considered the ideal kinetics for a gastroretentive system. Accordingly, this study can be seen as an advancement in ASD formulation for 3DP technology within pharmaceutics.

Design and fabrication of 3D-printed gastric floating tablets of captopril: effect of geometry and thermal crosslinking of polymer on floating behavior and drug release

The present study aims to investigate the potential of the 3D printing technique to design gastroretentive floating tablets (GFTs) for modifying the drug release profile of an immediate-release tablet. A 3D-printed floating shell enclosing a captopril tablet was designed having varying number of drug-release windows. The impact of geometrical changes in the design of delivery system and thermal cross-linking of polymers were evaluated to observe the influence on floating ability and drug release. Water uptake, water insolubilization, Differential Scanning Calorimetry (DSC), and Attenuated Total Reflection-Fourier Transform Infrared Spectroscopy (ATR-FTIR) were performed to assess the degree of thermal cross-linking of polyvinyl alcohol (PVA) filament. The 3D-printed GFT9 was considered the optimized gastric floating tablet that exhibited >12 h of total floating time with zero floating lag time and successfully accomplished modified-drug release by exhibiting >80% of drug release in 8 h. The zero-order release model, with an r2 value of 0.9923, best fitted the drug release kinetic data of the GFT9, which followed a super case II drug transport mechanism with an n value of 0.95. The optimized gastric floating device (GFT9) also exhibited the highest MDT values (238.55), representing slow drug release from the system due to thermal crosslinking and the presence of a single drug-releasing window in the device.

HME-assisted formulation of taste-masked dispersible tablets of cefpodoxime proxetil and roxithromycin

Objectives

Antibiotics are the most commonly administered medications among pediatric patients. However most of the time, accurate dose administration to children becomes a problem due to the extremely bitter taste. Cefpodoxime proxetil (CP) and roxithromycin (ROX) are antibiotics often prescribed to the pediatric population and have a bitter taste. Marketed formulations of these drugs are dry suspension and/or tablets. The lyophilization method involves various steps and thus is time consuming and expensive. The objective of this study was to mask the bitter taste of CP and ROX without compromising the solubility and drug release profile compared to marketed formulations, as well as to overcome the disadvantages associated with the currently used lyophilization technique.

Methods

Hot melt extrusion (HME) technology was used to process CP and ROX individually with Eudragit E PO polymer. The extrudates obtained were characterized by Fourier transform infrared spectroscopy, powder X-ray diffraction, and differential scanning calorimetry. The powdered extrudates were formulated as dispersible tablets and evaluated for in vitro and in vivo taste-masking efficiency.

Results

The tablets prepared in this study showed comparable dissolution profiles but the taste-masking efficiency was significantly enhanced compared to the marketed tablets of CP and ROX. The results of in vivo human taste-masking evaluation were also in agreement with the in vitro taste-masking studies.

Conclusion

The current work presents solvent-free, scalable, and continuous HME technology for addressing the bitter taste issues of CP and ROX. The disadvantages associated with the currently used lyophilization technique were overcome by developing the formulations using HME technology.

Understanding the Interaction of Thermal, Rheological, and Mechanical Parameters Critical for the Processability of Polyvinyl Alcohol-Based Systems during Hot Melt Extrusion

Hot melt extrusion (HME) is a common manufacturing process used in the pharmaceutical industry to improve the solubility of poorly soluble active pharmaceutical ingredients (API). The goal is to create an amorphous solid dispersion (ASD) where the amorphous form of the API is stabilized within a polymer matrix. Traditionally, the development of pharmaceutically approved polymers has focused on requirements such as thermal properties, solubility, drug-polymer interactions, and biocompatibility. The mechanical properties of the material have often been neglected in the design of new polymers. However, new downstream methods require more flexible polymers or suitable plasticizer polymer combinations. In this study, two grades of the polymer polyvinyl alcohol (PVA), which is already established for HME, are investigated in terms of their mechanical, rheological, and thermal properties. The mechanical properties of the extruded filaments were tested by the three-point bending test. The rheological behavior was analyzed by oscillating plate measurements. Thermal analysis was performed by differential scanning calorimetry (DSC). In addition, the solid and liquid plasticizers mannitol, sorbitol, triacetin, triethyl citrate, polyethylene glycol, and glycerol were evaluated for use with PVA and their impact on the polymer properties was elaborated. Finally, the effects of the plasticizers are compared to each other, and the correlations are analyzed statistically using principal component analysis (PCA). Thereby, a clear ranking of the plasticizer effects was established, and a deeper understanding of the polymer-plasticizer interactions was created.

Pediatric Formulations Developed by Extrusion-Based 3D Printing: From Past Discoveries to Future Prospects

Three-dimensional printing (3DP) technology in pharmaceutical areas is leading to a significant change in controlled drug delivery and pharmaceutical product development. Pharmaceutical industries and academics are becoming increasingly interested in this innovative technology due to its inherent inexpensiveness and rapid prototyping. The 3DP process could be established in the pharmaceutical industry to replace conventional large-scale manufacturing processes, particularly useful for personalizing pediatric drugs. For instance, shape, size, dosage, drug release and multi-drug combinations can be tailored according to the patient's needs. Pediatric drug development has a significant global impact due to the growing needs for accessible age-appropriate pediatric medicines and for acceptable drug products to ensure adherence to the prescribed treatment. Three-dimensional printing offers several significant advantages for clinical pharmaceutical drug development, such as the ability to personalize medicines, speed up drug manufacturing timelines and provide on-demand drugs in hospitals and pharmacies. The aim of this article is to highlight the benefits of extrusion-based 3D printing technology. The future potential of 3DP in pharmaceuticals has been widely shown in the last few years. This article summarizes the discoveries about pediatric pharmaceutical formulations which have been developed with extrusion-based technologies.

Facile fabrication of an extended-release tablet of Ticagrelor using three dimensional printing technology

The objective of the study was to fabricate tailored extended-release tablets of blood thinner Ticagrelor as once-daily dosing using additive manufacturing for better compliance in heart failure therapy. The solid work design of the tablet was printed using hot melt extrusion (HME) based 3D printing by optimized mixture of Eudragit RS-100, plasticizer and drug for producing extrudable and printable filaments. FTIR and TGA results showed no covalent interaction among ingredients and no decomposition during HME process, respectively. Friability, weight variation, assay and content uniformity tests met USP requirements, while the mean hardness of the tablets was calculated in a value between 40 and 50 kg. According to DSC and XRD results, the crystallinity state of the Ticagrelor was converted to an amorphous one in the tablet matrix. Smooth surfaces with multiple deposited layers were observed using SEM. In comparison, the maximum Ticagrelor release of 100% after 120 min from Brilinta® tablets was decreased to 97% in 400 min from the 3D tablet at infill of 90%. Korsmeyer-Peppas kinetic model showed the drug release mechanism is affected by diffusion and swelling. In general, fabrication of the extended-release 3D printed tablet of Ticagrelor using HME-based-additive manufacturing has the potential to provide specific doses with tailored kinetic release for personalized medicine, improving adherence at point-of-care.

3D Printed Personalized Colon-targeted Tablets: A Novel Approach in Ulcerative Colitis Management

Ulcerative colitis (UC) and Crohn's disease (CD) are two types of idiopathic inflammatory bowel disease (IBD) that are increasing in frequency and incidence worldwide, particularly in highly industrialized countries. Conventional tablets struggle to effectively deliver anti-inflammatory drugs since the inflammation is localized in different areas of the colon in each patient. The goal of 3D printing technology in pharmaceutics is to create personalized drug delivery systems (DDS) that are tailored to each individual's specific needs. This review provides an overview of existing 3D printing processes, with a focus on extrusion-based technologies, which have received the most attention. Personalized pharmaceutical products offer numerous benefits to patients worldwide, and 3D printing technology is becoming more affordable every day. Custom manufacturing of 3D printed tablets provides innovative ideas for developing a tailored colon DDS. In the future, 3D printing could be used to manufacture personalized tablets for UC patients based on the location of inflammation in the colon, resulting in improved therapeutic outcomes and a better quality of life.

Fused Deposition Modelling 3D printing and solubility improvement of BCS II and IV active ingredients - A narrative review

In the field of pharmaceutical research and development, Fused Deposition Modelling (FDM) 3D printing (3DP) has aroused growing interest within the last ten years. The use of thermoplastic polymers, combined with the melting process of the raw materials, offers the possibility of manufacturing amorphous solid dispersions (ASDs). In the pharmaceutical industry, the formulation of an ASD is a widely used strategy to improve the solubility of poorly soluble drugs (classified by the Biopharmaceutical Classification System (BCS) as class II and IV). In this review, an analysis of studies that have developed a FDM printed form containing a BCS class II or IV active substance was performed. The focus has been placed on the evaluation of the solid state of the active molecules (crystalline or amorphous) and on the study of their dissolution profile. Thus, the aim of this work is to highlight the interest of FDM 3DP to induce the amorphisation phenomenon of Class II and IV active substances by forming an ASD, and as result improving their solubility.

Strategies to improve the stability of amorphous solid dispersions in view of the hot melt extrusion (HME) method

Oral administration of drugs is preferred over other routes for several reasons: it is non-invasive, easy to administer, and easy to store. However, drug formulation for oral administration is often hindered by the drug's poor solubility, which limits its bioavailability and reduces its commercial value. As a solution, amorphous solid dispersion (ASD) was introduced as a drug formulation method that improves drug solubility by changing the molecular structure of the drugs from crystalline to amorphous. The hot melt extrusion (HME) method is emerging in the pharmaceutical industry as an alternative to manufacture ASD. However, despite solving solubility issues, ASD also exposes the drug to a high risk of crystallisation, either during processing or storage. Formulating a successful oral administration drug using ASD requires optimisation of the formulation, polymers, and HME manufacturing processes applied. This review presents some important considerations in ASD formulation, including strategies to improve the stability of the final product using HME to allow more new drugs to be formulated using this method.

Exploring Environmental Settings to Improve the Printability of Paroxetine-Loaded Filaments by Fused Deposition Modelling

The successful integration of hot-melt extrusion (HME) and fused deposition modelling (FDM) depends on a better understanding of the impact of environmental conditions on the printability of formulations, since they significantly affect the properties of the raw materials, whose control is crucial to enable three-dimensional printing (3DP). Hence, the objective of this work was to investigate the correlation between the environmental settings and the properties of paroxetine (PRX)-loaded filaments, previously produced by HME, which affect printability by FDM. The influence of different drying methods of the physical mixtures (PMs) and HME-filaments (FILs) on the quality and printability of these products was also assessed. The printability of FILs was evaluated in terms of the water content, and the mechanical and thermal properties of the products. Stability studies and physicochemical, thermal, and in vitro dissolution tests were carried out on the 3D-printed tablets. Stability studies demonstrated the high ductility of the PRX loaded FILs, especially under high humidity conditions. Under low humidity storage conditions (11% RH), the FILs became stiffer and were successfully used to feed the FDM printer. Water removal was slow when carried out passively in a controlled atmosphere (desiccator) or accelerated by using active drying methods (heat or microwave). Pre-drying of the PRX/excipients and/or PMs did not show any positive effect on the printability of the FIL. On the contrary, dry heat and, preferably, microwave mediated drying processes were shown to reduce the holding time required for successful FDM printing, enabling on-demand production at the point of care.

Diverse Applications of Three-Dimensional Printing in Biomedical Engineering: A Review

A three-dimensional (3D) printing is a robotically controlled state-of-the-art technology that is promising for all branches of engineering with a meritorious emphasis to biomedical engineering. The purpose of 3D printing (3DP) is to create exact superstructures without any framework in a brief period with high reproducibility to create intricate and complex patient-tailored structures for organ regeneration, drug delivery, imaging processes, designing personalized dose-specific tablets, developing 3D models of organs to plan surgery and to understand the pathology of disease, manufacturing cost-effective surgical tools, and fabricating implants and organ substitute devices for prolonging the lives of patients, etc. The formulation of bioinks and programmed G codes help to obtain precise 3D structures, which determines the stability and functioning of the 3D-printed structures. Three-dimensional printing for medical applications is ambitious and challenging but made possible with the culmination of research expertise from various fields. Exploring and expanding 3DP for biomedical and clinical applications can be life-saving solutions. The 3D printers are cost-effective and eco-friendly, as they do not release any toxic pollutants or waste materials that pollute the environment. The sampling requirements and processing parameters are amenable, which further eases the production. This review highlights the role of 3D printers in the health care sector, focusing on their roles in tablet development, imaging techniques, disease model development, and tissue regeneration.

Development of 3D-Printed Bicompartmental Devices by Dual-Nozzle Fused Deposition Modeling (FDM) for Colon-Specific Drug Delivery

Dual-nozzle fused deposition modeling (FDM) is a 3D printing technique that allows for the simultaneous printing of two polymeric filaments and the design of complex geometries. Hence, hybrid formulations and structurally different sections can be combined into the same dosage form to achieve customized drug release kinetics. The objective of this study was to develop a novel bicompartmental device by dual-nozzle FDM for colon-specific drug delivery. Hydroxypropylmethylcellulose acetate succinate (HPMCAS) and polyvinyl alcohol (PVA) were selected as matrix-forming polymers of the outer pH-dependent and the inner water-soluble compartments, respectively. 5-Aminosalicylic acid (5-ASA) was selected as the model drug. Drug-free HPMCAS and drug-loaded PVA filaments suitable for FDM were extruded, and their properties were assessed by thermal, X-ray diffraction, microscopy, and texture analysis techniques. 5-ASA (20% w/w) remained mostly crystalline in the PVA matrix. Filaments were successfully printed into bicompartmental devices combining an outer cylindrical compartment and an inner spiral-shaped compartment that communicates with the external media through an opening. Scanning electron microscopy and X-ray tomography analysis were performed to guarantee the quality of the 3D-printed devices. In vitro drug release tests demonstrated a pH-responsive biphasic release pattern: a slow and sustained release period (pH values of 1.2 and 6.8) controlled by drug diffusion followed by a faster drug release phase (pH 7.4) governed by polymer relaxation/erosion. Overall, this research demonstrates the feasibility of the dual-nozzle FDM technique to obtain an innovative 3D-printed bicompartmental device for targeting 5-ASA to the colon.

In-situ formation of nanoparticles from drug-loaded 3D polymeric matrices

The in-situ formation of nanoparticles from polymer-based solid medicines, although previously described, has been overlooked despite its potential to interfere with oral drug bioavailability. Such polymeric pharmaceuticals are becoming increasingly common on the market and can become even more popular due to the dizzying advance of 3D printing medicines. Hence, this work aimed to study this phenomenon during the dissolution of 3D printed tablets produced with three different polymers, hydroxypropylmethylcellulose acetate succinate (HPMCAS), polyvinyl alcohol (PVA), and Eudragit RL PO® (EUD RL) combined with plasticizers and the model drug naringenin (NAR). The components' interaction, dissolution behavior, and characteristics of the formed particles were investigated employing thermal, spectroscopic, mechanical, and chromatographic assays. All the systems generated stable spherical-shaped particles throughout 24 h, encapsulating over 25% of NAR. Results suggest encapsulation efficiencies variations may depend on interactions between polymer-drug, drug-plasticizer, and polymer-plasticizer, which formed stable nanoparticles even in the drug absence, as observed with the HPMCAS and EUD RL formulations. Additionally, components solubility in the medium and previous formulation treatments are also a decisive factor for nanoparticle formation. In particular, the treatment provided by hot-melt extrusion and FDM 3D printing affected the dissolution efficiency enhancing the interaction between the components, reverberating on particle size and particle formation kinetics mainly for HPMCAS and EUD RL. In conclusion, the 3D printing process influences the in-situ formation of nanoparticles, which can directly affect oral drug bioavailability and needs to be monitored.

Factors That Influence Sustained Release from Hot-Melt Extrudates

Hot-melt extrusion is a well-established tool in the pharmaceutical industry, mostly implemented to increase the solubility of poorly soluble drugs. A less frequent application of this technique is to obtain formulations with extended release. This study investigated the influence of polymer choice, drug loading, milling and hydrodynamics on the release of a model drug, flurbiprofen, from sustained-release hot-melt extrudates with Eudragit polymers. The choice of polymer and degree of particle size reduction of the extrudate by milling were the two key influences on the release profile: the percentage release after 12 h varied from 6% (2 mm threads) to 84% (particle size <125 µm) for Eudragit RL extrudates vs. 4.5 to 62% for the corresponding Eudragit RS extrudates. By contrast, the release profile was largely independent of drug loading and robust to hydrodynamics in the dissolution vessel. Thus, hot-melt extrusion offers the ability to tailor the release of the API to the therapeutic indication through a combination of particle size and polymer choice while providing robustness over a wide range of hydrodynamic conditions.

Additive Manufacturing of an Extended-Release Tablet of Tacrolimus

An extended-release tablet of tacrolimus as once-daily dosing was fabricated using 3D printing technology. It was developed by combining two 3D-printing methods in parallel. Indeed, an optimized mixture of PVA, sorbitol, and magnesium stearate as a shell compartment was printed through a hot-melt extrusion (HME) nozzle while an HPMC gel mixture of the drug in the core compartment was printed by a pressure-assisted micro-syringe (PAM). A 3D-printed tablet with an infill of 90% was selected as an optimized formula upon the desired dissolution profile, releasing 86% of the drug at 12 h, similar to the commercial one. The weight variation, friability, hardness, assay, and content uniformity determination met USP requirements. A microbial evaluation showed that the 3D-printed tablet does not support microbial growth. SEM analysis showed smooth surfaces with multiple deposited layers. No peak interference appeared based on FTIR analysis. No decomposition of the polymer and drug was observed in the printing temperature, and no change in tacrolimus crystallinity was detected based on TGA and DSC analyses, respectively. The novel, sTable 3D-printed tablet, fabricated using controllable additive manufacturing, can quickly provide tailored dosing with specific kinetic release for personalized medicine at the point-of-care.

A Review on Physicochemical Properties of Polymers Used as Filaments in 3D-Printed Tablets

Three-dimensional (3D) printing technology has presently been explored widely in the field of pharmaceutical research to produce various conventional as well as novel dosage forms such as tablets, capsules, oral films, pellets, subcutaneous implants, scaffolds, and vaginal rings. The use of this innovative method is a good choice for its advanced technologies and the ability to make tailored medicine specifically for individual patient. There are many 3D printing systems that are used to print tablets, implants, and vaginal rings. Among the available systems, the fused deposition modeling (FDM) is widely utilized. The FDM has been regarded as the best choice of printer as it shows high potential in the production of tablets as a unit dose in 3D printing medicine manufacturing. In order to design a 3D-printed tablet or other dosage forms, the physicochemical properties of polymers play a vital role. One should have proper knowledge about the polymer's properties so that one can select appropriate polymers in order to design 3D-printed dosage form. This review highlighted the various physicochemical properties of polymers that are currently used as filaments in 3D printing. In this manuscript, the authors also discussed various systems that are currently adopted in the 3D printing.

Influence of formulation variables on the processability and properties of tablets manufactured by fused deposition modelling

The present work studied the influence of different formulation variables (defined also as factors), namely, different polymers (HPC EF, PVA and HPMC-AS LG), drugs with different water solubilities (paracetamol, hydrochlorothiazide and celecoxib) and drug loads (10 or 30 %) on their processability by HME and FDM. Both filaments and tablets were characterized for physic and chemical properties (DSC, XRPD, FTIR) and performance properties (drug content, in vitro drug release). Experiments were designed to highlight relationships between the 3 factors selected and the mechanical properties of filaments, tablet mass and dissolution profiles of the model drugs from printed tablets. While the combination of hydrochlorothiazide and HPMC-AS LG could not be extruded, the combination of paracetamol with HPC EF turned the filaments too ductile and not stiff enough hampering the process of printing. All other polymer and drug combinations could be successfully extruded and printed. Models reflected the influence of the solubility of the drug considered but not the drug load in formulations. The ranking of the drug release rates was in good agreement with their solubilities. Furthermore, PVA presenting the fastest swelling rate, promoted the fastest drugs' releases in comparison with the other polymers studied. Overall, the study enabled the identification of the key factors affecting the properties of printed tablets, with the proposal of a model that has valued the relative contribution of each factor to the overall performance of tablets.

Design and Characterization of Baricitinib Incorporated PLA 3D Printed Pills by Fused Deposition Modeling: An Oral Pill for Treating Alopecia Areata

This study aimed to develop three-dimensional (3D) baricitinib (BAB) pills using polylactic acid (PLA) by fused deposition modeling. Two strengths of BAB (2 and 4% w/v) were dissolved into the (1:1) PEG-400 individually, diluting it with a solvent blend of acetone and ethanol (27.8:18:2) followed by soaking the unprocessed 200 cm~6157.94 mg PLA filament in the solvent blend acetone-ethanol. FTIR spectrums of the 3DP1 and 3DP2 filaments calculated and recognized drug encapsulation in PLA. Herein, 3D-printed pills showed the amorphousness of infused BAB in the filament, as indicated by DSC thermograms. Fabricated pills shaped like doughnuts increased the surface area and drug diffusion. The releases from 3DP1 and 3DP2 were found to be 43.76 ± 3.34% and 59.14 ± 4.54% for 24 h. The improved dissolution in 3DP2 could be due to the higher loading of BAB due to higher concentration. Both pills followed Korsmeyer-Peppas' order of drug release. BAB is a novel JAK inhibitor that U.S. FDA has recently approved to treat alopecia areata (AA). Therefore, the proposed 3D printed tablets can be easily fabricated with FDM technology and effectively used in various acute and chronic conditions as personalized medicine at an economical cost.

3D Printed Pharmaceutical Systems for Personalized Treatment in Metabolic Syndrome

The current healthcare system is widely based on the concept of “one size fit for all”, which emphasizes treating a disease by prescribing the same drug to all patients with equivalent doses and dosing frequency. This medical treatment scenario has shown varied responses with either no or weak pharmacological effects and exaggerated adverse reactions preceded by more patient complications. The hitches to the concept of “one size fits all” have devoted the attention of many researchers to unlocking the concept of personalized medicine (PM). PM delivers customized therapy with the highest safety margin for an individual patient’s needs. PM has the potential to revolutionize the current healthcare system and pave the way to alter drug choices and doses according to a patient’s clinical responses, providing physicians with the best treatment outcomes. The 3D printing techniques is a solid-form fabrication method whereby successive layers of materials based on computer-aided designs were deposited to form 3D structures. The 3D printed formulation achieves PM goals by delivering the desired dose according to patient needs and drug release profile to achieve a patient’s personal therapeutic and nutritional needs. This pre-designed drug release profile attains optimum absorption and distribution, exhibiting maximum efficacy and safety profiles. This review aims to focus on the role of the 3D printing technique as a promising tool to design PM in metabolic syndrome (MS).

Improving drug release rate, drug-polymer miscibility, printability and processability of FDM 3D-printed tablets by weak acid-base interaction

Slow drug release, low drug-polymer miscibility, poor printability of polymers used, and high processing temperature are major challenges in developing FDM 3D-printed tablets. These challenges were addressed in this investigation by having a model basic drug, haloperidol (mp: 151.5 °C), interact with a weak acid, malic acid (mp: 130 °C), during the melt extrusion of formulations into filaments used for 3D-printing. Malic acid was selected as it was previously reported that it did not form any crystalline salt with haloperidol but its addition to aqueous media could greatly increase the solubility of haloperidol from ∼ 1 µg/mL to > 1 g per mL of water by acid-base supersolubilization. Concentrated solutions of haloperidol-malic acid mixtures produced amorphous materials upon drying. It has been observed in the present investigation that similar interaction between haloperidol and malic acid may also occur in the absence of water. Upon heating, haloperidol-malic acid mixtures at 1:1 and 1:2 molar ratios turned amorphous starting at ∼ 50 °C, which is much below the melting point of either component. When Kollidon® VA64, a brittle and non-printable polymer, was used as the polymeric carrier, the acid-base interaction greatly reduced the melt viscosity of haloperidol-malic acid-Kollidon® VA64 ternary mixtures. Consequently, melt extrusion of filaments and printing of tablets using such mixtures could be performed at much lower temperatures than those with haloperidol-Kollidon® VA64 binary mixtures. The filaments containing 15 % and 30 % haloperidol along with malic acid and Kollidon® VA64 could be printed into tablets at relatively low temperatures of 125 and 100 °C, respectively, thus making Kollidon® VA64 not only printable but also doing so at low temperatures. Up to 50 % w/w drug load in filaments was achieved without any crystallization of haloperidol or malic acid. Drug release at pH 2 and 6.8 from printed tablets with 100 % infill was 80 % in < 30 min. Thus, the acid-base interaction can successfully resolve multiple development challenges encountered with FDM 3D-printed tablets.

Controlled Release of Felodipine from 3D-Printed Tablets with Constant Surface Area: Influence of Surface Geometry

In this study, 3D-printed tablets with a constant surface area were designed and fabricated using polylactic acid (PLA) in the outer compartment and polyvinyl alcohol and felodipine (FDP) in the inner compartment. The influences of different surface geometries of the inner compartment, namely, round, hexagon, square, and triangle, on drug release from 3D-printed tablets were also studied. The morphology and porosity of the inner compartment were determined using scanning electron microscopy and synchrotron radiation X-ray tomographic microscopy, respectively. Additionally, drug content and drug release were also evaluated. The results revealed that the round-shaped geometry seemed to have the greatest total surface area of the inner compartment, followed by square-shaped, hexagon-shaped, and triangle-shaped geometries. FDP-loaded 3D-printed tablets with triangle and hexagon surface geometries had the slowest drug release (about 80% within 24 h). In the round-shaped and square-shaped 3D-printed tablets, complete drug release was observed within 12 h. Furthermore, the drug release from triangle-shaped 3D-printed tablets with double the volume of the inner compartment was faster than that of a smaller volume. This was due to the fact that a larger tablet volume increased the surface area contacting the medium, resulting in a faster drug release. The findings indicated that the surface geometry of 3D-printed tablets with a constant surface area affected drug release. This study suggests that 3D printing technology may be used to develop oral solid dosage forms suitable for customized therapeutic treatments.

Formulation development and in Vitro-Ex vivo characterization of hot-melt extruded ciprofloxacin hydrochloride inserts for ocular applications: Part I

This study developed, optimized, characterized, and evaluated bioadhesive, hot-melt extruded (HME), extended-release ocular inserts containing ciprofloxacin hydrochloride (CIP-HCL) to improve the therapeutic outcomes of ocular bacterial infections. The inserts were fabricated with FDA-approved biocompatible, biodegradable, and bioadhesive polymers that were tuned in different ratios to achieve a sustained release profile. The results revealed an inverse relationship between the Klucel™ hydroxypropyl cellulose (HPC, 140,000 Da) concentration and drug release and extended-release profile over 24 h. The CIP-HCL-HME inserts presented stable drug content, thermal behavior, surface pH, and release profiles over three months of room-temperature storage and demonstrated adequate mucoadhesive strength. SEM micrographs revealed a smooth surface. Bacterial growth was not observed on the samples during the in vitro release experiment (0.5-24 h), indicating that a minimum inhibitory concentration (MIC) of 90 against Pseudomonas aeruginosa was achieved. Ex vivo transcorneal permeation studies using excised rabbit corneas revealed that the prepared ocular inserts prolonged the transcorneal flux of the drug compared to commercial eye drops and immediate-release inserts and could reduce the administration frequency to once daily. Therefore, the inserts could increase patient compliance and exhibited prolonged antibacterial activity and thus could provide better therapeutic outcomes against ocular bacterial infections.

Challenges, current status and emerging strategies in the development of rapidly dissolving FDM 3D-printed tablets: An overview and commentary

Since the approval of a 3D-printed tablet by the FDA in 2015 for marketing, there has been a great interest in 3D printing in the pharmaceutical field for the development of personalized and on-demand medications. Among various 3D printing methods explored for the development of oral solid dosage form like tablet, the fused deposition modeling (FDM) 3D-printing, where the drug-polymer mixtures are first converted into filaments by hot melt extrusion (HME) and then the filaments are printed into tablets using 3D printers by applying computer-aided design principles, has emerged as the most attractive option. However, no FDM 3D-printed tablets have yet been marketed as the technology faces many challenges, such as limited availability of pharmaceutical-grade polymers that can be printed into tablets, low drug-polymer miscibility, the need for high temperature for HME and 3D-printing, and slow drug release rates from tablets. These challenges are discussed in this article with a special focus on drug release rates since FDM 3D-printing usually leads to the preparation of slow-release tablets while the rapid release from dosage forms is often desired for optimal therapeutic outcomes of new drug candidates. Pros and cons of various strategies for the development of rapidly dissolving FDM 3D-printed tablets reported in the literature are reviewed. Finally, two case studies on emerging strategies for the development of rapidly dissolving FDM 3D-printed tablets are presented, where one outlines a systematic approach for formulating rapidly dissolving tablets, and the other describes a novel strategy to increase dissolution rates of drugs from FDM 3D-printed tablets, which at the same time can also increase drug-polymer miscibility and printability of tablets and lower processing temperatures. Thus, this overview and commentary discusses various issues involving the formulation of rapidly dissolving FDM 3D-printed tablets and provides guidance for the development of commercially viable products.

Formation of a Stable Co-Amorphous System for a Brick Dust Molecule by Utilizing Sodium Taurocholate with High Glass Transition Temperature

Brick dust molecules are usually poorly soluble in water and lipoidal components, making it difficult to formulate them in dosage forms that provide efficient pharmacological effects. A co-amorphous system is an effective strategy to resolve these issues. However, their glass transition temperatures (Tg) are relatively lower than those of polymeric amorphous solid dispersions, suggesting the instability of the co-amorphous system. This study aimed to formulate a stable co-amorphous system for brick dust molecules by utilizing sodium taurocholate (NaTC) with a higher Tg. A novel neuropeptide Y5 receptor antagonist (AntiY5R) and NaTC with Tg of 155 °C were used as the brick dust model and coformer, respectively. Ball milling formed a co-amorphous system for AntiY5R and NaTC (AntiY5R-NaTC) at various molar ratios. Deviation from the theoretical Tg value and peak shifts in Fourier-transform infrared spectroscopy indicated intermolecular interactions between AntiY5R and NaTC. AntiY5R-NaTC at equal molar ratios resulting in an 8.5-fold increase in AntiY5R solubility over its crystalline form. The co-amorphous system remained amorphous for 1 month at 25 °C and 40 °C. These results suggest that the co-amorphous system formed by utilizing NaTC as a coformer could stably maintain the amorphous state and enhance the solubility of brick dust molecules.

3D printing hybrid materials using fused deposition modelling for solid oral dosage forms

3D printing in the pharmaceutical and healthcare settings is expanding rapidly, such as the rapid prototyping of orthotics, dental retainers, drug-loaded implants, and pharmaceutical solid oral dosage forms. Through 3D printing, we have the capability to precisely control dose, release kinetics, and several aesthetic features of dosage forms such as colour, shape, and texture. Additionally, polypills can be created with combinations of medications in one solid dosage form at completely customisable strengths that would be extremely difficult to obtain commercially. As the technology and formulations developed through 3D printing are expanding, the development of new hybrid materials to obtain superior formulations are also gaining momentum. In this review we collate data on the importance of developing hybrid formulations of polymers, drugs and excipients necessary to produce reliable and high-quality 3D printed dosage forms with a special emphasis on fused deposition modelling (FDM). FDM technology is one of the most widely used forms of 3D printing and has demonstrated compatibility with unique polymer-based hybrids to allow for enhanced drug delivery, protection of thermolabile drugs, modifiable release kinetics, and more. The data collated covers different categories of hybrids as well as the methods used to fabricate them, and their respective effects on the properties of 3D printed solid oral dosage forms. Therefore, this review will provide an overview of upcoming and emerging trends in pharmaceutical 3D printing formulation compositions.

3D Printed Fractal-like Structures with High Percentage of Drug for Zero-Order Colonic Release

Colonic drug delivery of drugs is an area of great interest due to the need to treat high prevalence colonic local diseases as well as systemic conditions that may benefit from the advantages associated to this route of drug administration. In the last decade, the use of 3D printing technologies has expanded, offering the possibility of preparing personalized medicines in small batches directly at the point of care. The aim of this work is to design a high drug loaded 3D printed system prepared by a combination of Fused Deposition Modelling (FDM) and Injection Volume Filling (IVF) techniques intended for zero-order colonic drug release. For this purpose, different batches of binary and ternary filaments based on the thermoplastic polyurethane Tecoflex EG-72D (TPU), theophylline anhydrous (AT) as model drug, and magnesium stearate as lubricant have been developed and characterized. Filaments with the highest drug load and the best rheological properties were selected for the manufacture of a printed fractal-like structure based on multiple toroids. This design was proposed to provide high surface area, leading to increased drug release and water uptake in the colonic region. This structure was 3D printed by FDM and then coated in a unique step by IVF technology using the enteric polymer DrugCoat S 12.5. This way, an additional coating process is avoided, reducing costs and production time. Studies of drug release confirmed the ability of the structures to provide a five-hour period of constant drug delivery in the colonic region.

Evaluation of Hydroxyethyl Cellulose Grades as the Main Matrix Former to Produce 3D-Printed Controlled-Release Dosage Forms

Diclofenac sodium tablets were successfully prepared via hot-melt extrusion (HME) and fused deposition modeling (FDM), using different molecular-weight (Mw) grades of hydroxyethyl cellulose (HEC) as the main excipient. Hydroxypropyl cellulose (HPC) was added to facilitate HME and to produce drug-loaded, uniform filaments. The effect of the HEC grades (90–1000 kDa) on the processability of HME and FDM was assessed. Mechanical properties of the filaments were evaluated using the three-point bend (3PB) test. Breaking stress and distance were set in relation to the filament feedability to identify printer-specific thresholds that enable proper feeding. The study demonstrated that despite the HEC grade used, all formulations were at least printable. However, only the HEC L formulation was feedable, showing the highest breaking stress (29.40 ± 1.52 MPa) and distance (1.54 ± 0.08 mm). Tablet drug release showed that the release was Mw dependent up to a certain HEC Mw limit (720 kDa). Overall, the release was driven by anomalous transport due to drug diffusion and polymer erosion. The results indicate that despite being underused in FDM, HEC is a suitable main excipient for 3D-printed dosage forms. More research on underutilized polymers in FDM should be encouraged to increase the limited availability.

Immediate release 3D printed oral dosage forms: How different polymers have been explored to reach suitable drug release behaviour

Three-dimensional (3D) printing has been gaining attention as a new technological approach to obtain immediate release (IR) dosage forms. The versatility conferred by 3D printing techniques arises from the suitability of using different polymeric materials in the production of solids with different porosities, geometries, sizes, and infill patterns. The appropriate choice of polymer can facilitate in reaching IR specifications and afford other specific properties to 3D printed solid dosage forms. This review aims to provide an overview of the polymers that have been employed in the development of IR 3D printed dosage forms, mainly considering their in vitro drug release behaviour. The physicochemical and mechanical properties of the IR 3D printed dosage forms will also be discussed, together with the manufacturing process strategies. Up to now, methacrylic polymers, cellulosic polymers, vinyl derivatives, glycols and different polymeric blends have been explored to produce IR 3D printed dosage forms. Their effects on drug release profiles are critically discussed here, giving a complete overview to drive formulators towards a rational choice of polymeric material and thus contributing to future studies in 3D printing of pharmaceuticals.

Investigation of Patient-Centric 3D-Printed Orodispersible Films Containing Amorphous Aripiprazole

The objective of this study was to design and evaluate an orodispersible film (ODF) composed of aripiprazole (ARP), prepared using a conventional solvent casting technique, and to fuse a three-dimensional (3D) printing technique with a hot-melt extrusion (HME) filament. Klucel® LF (hydroxypropyl cellulose, HPC) and PE-05JPS® (polyvinyl alcohol, PVA) were used as backbone polymers for 3D printing and solvent casting. HPC-, PVA-, and ARP-loaded filaments were applied for 3D printing using HME. The physicochemical and mechanical properties of the 3D printing filaments and films were optimized based on the composition of the polymers and the processing parameters. The crystalline states of drug and drug-loaded formulations were investigated using differential scanning calorimetry (DSC) and powder X-ray diffraction (XRD). The dissolution and disintegration of the 3D-printed films were faster than those of solvent-cast films. HPC-3D printed film was fully disintegrated within 45 ± 3.5 s. The dissolution rate of HPC films reached 80% within 30 min at pH 1.2 and pH 4.0 USP buffer. There was a difference in the dissolution rate of about 5 to 10% compared to PVA films at the same sampling time. The root mean square of the roughness (Rq) values of each sample were evaluated using atomic force microscopy. The higher the Rq value, the rougher the surface, and the larger the surface area, the more salivary fluid penetrated the film, resulting in faster drug release and disintegration. Specifically, The HPC 3D-printed film showed the highest Rq value (102.868 nm) and average surface roughness (85.007 nm). The puncture strength of 3D-printed films had desirable strength with HPC (0.65 ± 0.27 N/mm2) and PVA (0.93 ± 0.15 N/mm2) to prevent deformation compared to those of marketed film products (over 0.34 N/mm2). In conclusion, combining polymer selection and 3D printing technology could innovatively design ODFs composed of ARP to solve the unmet medical needs of psychiatric patients.

Filament-based 3D-printing of placebo dosage forms using brittle lipid-based excipients

In order to expand the limited portfolio of available polymer-based excipients for fabricating three-dimensional (3D) printed pharmaceutical products, Lipid-based excipients (LBEs) have yet to be thoroughly investigated. The technical obstacle of LBEs application is, however their crystalline nature that renders them very brittle and challenging for processing via 3D-printing. In this work, we evaluated the functionality of LBEs for filament-based 3D-printing of oral dosage forms. Polyglycerol partial ester of palmitic acid and polyethylene glycols monostearate were selected as LBEs, based on their chemical structure, possessing polar groups for providing hydrogen-bonding sites. A fundamental understanding of structure-function relationship was built to screen the critical material attributes relevant for both extrusion and 3D-printing processes. The thermal behavior of lipids, including the degree of their supercooling, was the critical attribute for their processing. The extrudability of materials was improved through different feeding approaches, including the common powder feeding and a devised liquid feeding setup. Liquid feeding was found to be more efficient, allowing the production of filaments with high flexibility and improved printability. Filaments with superior performance were produced using polyglycerol ester of palmitic acid. In-house designed modifications of the utilized 3D-printer were essential for a flawless processing of the filaments.

Fiber Spinning from Cellulose Solutions in Imidazolium Ionic Liquids: Effects of Natural Antioxidants on Molecular Weight, Dope Discoloration, and Yellowing Behavior

Spinning of cellulosic fibers requires the prior dissolution of cellulose. 3-Alkyl-1-methylimidazolium ionic liquids have proven to be suitable solvents for that purpose, but the degradation of cellulose in the spinning dope can be severe. Suitable stabilizers are therefore required that prevent cellulose degradation, but do not adversely affect spinnability or the long-term yellowing behavior of the fibers. A group of twelve renewables-based antioxidants was selected for stabilizing 5% cellulose solutions in the ionic liquids and their effects on cellulose integrity, dope discoloration, and aging behavior were tested by gel permeation chromatography (GPC) and ISO brightness measurements. Propyl gallate (a gallic acid derivative), hydroxytyrosol (from olives), and tocopheramines (a vitamin E derivative) performed best in the three test categories, minimizing both cellulose degradation, chromophore formation in the spinning dope, and yellowing upon accelerating aging of the spun fibers. The use of these stabilizers for cellulose solutions in the imidazolium-based solvent system can therefore be recommended from the point of view of both performance and sustainability.

Additive Manufacturing Strategies for Personalized Drug Delivery Systems and Medical Devices: Fused Filament Fabrication and Semi Solid Extrusion

Novel additive manufacturing (AM) techniques and particularly 3D printing (3DP) have achieved a decade of success in pharmaceutical and biomedical fields. Highly innovative personalized therapeutical solutions may be designed and manufactured through a layer-by-layer approach starting from a digital model realized according to the needs of a specific patient or a patient group. The combination of patient-tailored drug dose, dosage, or diagnostic form (shape and size) and drug release adjustment has the potential to ensure the optimal patient therapy. Among the different 3D printing techniques, extrusion-based technologies, such as fused filament fabrication (FFF) and semi solid extrusion (SSE), are the most investigated for their high versatility, precision, feasibility, and cheapness. This review provides an overview on different 3DP techniques to produce personalized drug delivery systems and medical devices, highlighting, for each method, the critical printing process parameters, the main starting materials, as well as advantages and limitations. Furthermore, the recent developments of fused filament fabrication and semi solid extrusion 3DP are discussed. In this regard, the current state of the art, based on a detailed literature survey of the different 3D products printed via extrusion-based techniques, envisioning future directions in the clinical applications and diffusion of such systems, is summarized.

The Development of Innovative Dosage Forms of the Fixed-Dose Combination of Active Pharmaceutical Ingredients

The development of innovative forms of combination drugs is closely related to the invention of the multilayer tablet press, polymers for pharmaceutical applications, the hot-melt extrusion process, and 3D printing in the pharmaceutical industry. However, combining multiple drugs within the same dosage form can bring many physicochemical and pharmacodynamic interactions. More and more new forms of fixed-dose combinations (FDCs) have been developed due to work to overcome the incompatibility of active substances or to obtain different drug release profiles in the same dosage form. This review provides discussions of the application of various innovation formulation technologies of FDC drugs such as bilayer system, multilayer tablet, active film coating, hot-melt extrusion, and 3D printing, taking into account the characteristics of the key ingredients in the FDC formulation and presenting technological problems and challenges related to the development of combination drugs. Moreover, the article summarizes the range of dosage forms that have been made using these technologies over the past 30 years.

3D printing of pharmaceutical oral solid dosage forms by fused deposition: the enhancement of printability using plasticised HPMCAS

3D printing (3DP) by fused deposition modelling (FDM) is one of the most extensively developed methods in additive manufacturing. Optimizing printability by improving feedability, nozzle extrusion, and layer deposition is crucial for manufacturing solid oral dosage forms with desirable properties. This work aimed to use HPMCAS (Affinisol^TM HPMCAS 716) to prepare filaments for FDM-3DP using hot-melt extrusion (HME). It explored and demonstrated the effect of HME-filament composition and fabrication on printability by evaluating thermal, mechanical, and thermo-rheological properties. It also showed that the HME-Polymer filament composition used in FDM-3DP manufacture of oral solid dosage forms provides a tailored drug release profile. HME (HAAKE MiniLab) and FDM-3DP (MakerBot) were used to prepare HME-filaments and printed objects, respectively. Two diverse ways of improving the mechanical properties of HME-filaments were deduced by changing the formulation to enable feeding through the roller gears of the printer nozzle. These include plasticizing the polymer and adding an insoluble structuring agent (talc) into the formulation. Experimental feedability was predicted using texture analysis results was a function of PEG concentration, and glass-transition temperature (T_g) values of HME-filaments. The effect of high HME screw speed (100 rpm) resulted in inhomogeneity of HME-filament, which resulted in inconsistency of the printer nozzle extrudate and printed layers. The variability of the glass-transition temperature (T_g) of the HME-filament supported by scanning electron microscopy (SEM) images of nozzle extrudates and the lateral wall of the printed tablet helped explain this result. The melt viscosity of HPMCAS formulations was investigated using a capillary rheometer. The high viscosity of unplasticized HPMCAS was concluded to be an additional restriction for nozzle extrusion. The plasticization of HPMCAS and the addition of talc into the formulation were shown to improve thickness consistency of printed layers (using homogeneous HME-filaments). A good correlation (R²=0.9546) between the solidification threshold (low-frequency oscillation test determined by parallel-plate rheometer) and T_g of HME-filaments was also established. Drug-loaded and placebo HPMCAS-based formulations were shown to be successfully printed, with the former providing tailored drug release profiles based on variation of internal geometry (infill).

Coupling of Fused Deposition Modeling and Inkjet Printing to Produce Drug Loaded 3D Printed Tablets

In the current study, we have coupled Fused Deposition Modelling (FDM) for the fabrication of plain polyvinyl alcohol (PVA) tablets followed by dispensing of minoxidil ethanolic solutions using inkjet printing. The use of a drop-on-solid printing approach facilitates an accurate and reproducible process while it controls the deposition of the drug amounts. For the purpose of the study, the effect of the solvent was investigated and minoxidil ink solutions of ethanol 70% v/v (P70) or absolute ethanol (P100) were applied on the plain PVA tablets. Physicochemical characterization showed that solvent miscibility with the polymer substrate plays a key role and can lead to the formation of drug crystals on the surface or drug absorption in the polymer matrix. The produced minoxidil tablets showed sustained release profiles or initial bursts strongly affected by the solvent grade used for dispensing the required dose on drug loaded 3D printed tablets. This paradigm demonstrates that the coupling of FDM and inkjet printing technologies could be used for rapid development of personalized dosage forms.

Hot-melt extrudability of amorphous solid dispersions of flubendazole-copovidone: An exploratory study of the effect of drug loading and the balance of adjuvants on extrudability and dissolution

The FDA-approved anthelmintic flubendazole has shown potential to be repositioned to treat cancer and dry macular degeneration; however, its poor water solubility limits its use. Amorphous solid dispersions may overcome this challenge, but the balance of excipients may impact the preparation method and drug release. The purpose of this study was to evaluate the influence of adjuvants and drug loading on the development of an amorphous solid dispersion of flubendazole-copovidone by hot-melt extrusion. The drug, copovidone, and adjuvants (magnesium stearate and hydroxypropyl cellulose) mixtures were statistically designed, and the process was performed in a twin-screw extruder. The study showed that flubendazole and copovidone mixtures were highly extrudable, except when drug loading was high (>40%). Furthermore, magnesium stearate positively impacted the extrusion and was more effective than hydroxypropyl cellulose. The extruded materials were evaluated by modulated differential scanning calorimetry and X-ray powder diffraction, obtaining positive amorphization and physical stability results. Pair distribution function analysis indicated the presence of drug-rich domains with medium-range order structure and no evidence of polymer-drug interaction. All extrudates presented faster dissolution (HCl, pH 1.2) than pure flubendazole, and both adjuvants had a notable influence on the dissolution rate. In conclusion, hot-melt extrusion may be a viable option to obtain stable flubendazole:copovidone amorphous dispersions.

The potential of natural products use in fused deposition modeling 3D printing of pharmaceutical dosage forms

In recent years, the interest in 3D printing of medicines has increased due to many advantages of this technology, such as flexibility of the dose and dosage form of the printed product. Fused deposition modeling (FDM) is one of the most popular 3D printing technologies in the pharmaceutical field, due to its low cost and simplicity. The subject of this review is the potential use of natural products as biodegradable and biocompatible materials with good safety profiles in FDM 3D printing of pharmaceuticals. Natural products such as alginate, chitosan and starch have already been employed as excipients in FDM 3D printed pharmaceutical dosage forms, while others like shellac and zein show the potential, but haven't yet been part of 3D printed pharmaceutical formulations. These excipients have different roles in the formulation of filaments for FDM 3D printing, for example as fillers, matrix carriers or drug-release modifiers. In addition, the possibility of incorporating active pharmaceutical ingredients of natural origin in filaments for FDM 3D printing was reviewed. High printing temperatures limit the use of natural products in FDM 3D printing. However, adequate selection of thermoplastic material and printing parameters can widen the use of natural products in FDM 3D printing of pharmaceutical dosage forms.

Recent Progress in Hot Melt Extrusion Technology in Pharmaceutical Dosage Form Design

BACKGROUND

The Hot Melt Extrusion (HME) technique has shown tremendous potential in transforming highly hydrophobic crystalline drug substances into amorphous solids without using solvents. This review explores in detail the general considerations involved in the process of HME, its applications and advances.

OBJECTIVE

The present review examines the physicochemical properties of polymers pertinent to the HME process. Theoretical approaches for the screening of polymers are highlighted as a part of successful HME processed drug products. The critical quality attributes associated with the process of HME are also discussed in this review. HME plays a significant role in the dosage form design, and the same has been mentioned with suitable examples. The role of HME in developing several sustained release formulations, films, and implants is described along with the research carried out in a similar domain.

METHODS

The method includes the collection of data from different search engines like PubMed, ScienceDirect, and SciFinder to get coverage of relevant literature for accumulating appropriate information regarding HME, its importance in pharmaceutical product development, and advanced applications.

RESULTS

HME is known to have advanced pharmaceutical applications in the domains related to 3D printing, nanotechnology, and PAT technology. HME-based technologies explored using Design-of- Experiments also lead to the systematic development of pharmaceutical formulations.

CONCLUSION

HME remains an adaptable and differentiated technique for overall formulation development.

Determination of feed forces to improve process understanding of Fused Deposition Modeling 3D printing and to ensure mass conformity of printed solid oral dosage forms

Fused Deposition Modeling is a suitable technique for the production of personalized solid oral dosage forms. For widespread application, it is necessary to be able to print a wide range of different formulations to address individual therapeutic needs. Due to the complexity of formulation composition (e.g., due to different compounds, excipients for enhancement of release and mechanical properties) and limited mechanical understanding, determination of suitable printing parameters is challenging. To address this challenge, we have developed a feed force tester using a Texture Analyser setup that mimics the actual printing process. Feed force data were compared to the mass of tablets printed from technical materials as well as pharmaceutical filaments of ketoconazole at high drug loads of 20 and 40% and polyvinyl alcohol. By determining a feed force limit for the 3D printer from feed force data of several formulations printed, it was possible to specify the operable printing range, where printing is reproducible and printed mass corresponds the target mass. Based on these results, rational optimization of the printing process in terms of speed, time and temperature for different materials and formulations is possible.

Preformulation Studies to Guide the Production of Medicines by Fused Deposition Modeling 3D Printing

Fused deposition modeling (FDM) 3D printing has demonstrated high potential for the production of personalized medicines. However, the heating at high temperatures inherent to this process causes unknown risks to the drug product's stability. The present study aimed to assess the use of a tailored preformulation protocol involving physicochemical assessments, including the rheological profiles of the samples, to guide the development of medicines by FDM 3D printing. For this, polymers commonly used in FDM printing, i.e., high impact polystyrene (HIPS), polylactic acid (PLA), and polyvinyl alcohol (PVA), and their common plasticizers (mineral oil, triethyl citrate, and glycerol, respectively) were evaluated using the thermolabile model drug isoniazid (INH). Samples were analyzed by chemical and physical assays. The results showed that although the drug could produce polymorphs under thermal processing, the polymeric matrix can be a protective element, and no polymorphic transformation was observed. However, incompatibilities between materials might impact their chemical, thermal, and rheological performances. In fact, ternary mixtures of INH, PLA, and TEC showed a major alteration in their viscoelastic behavior besides the chemical changes. On the other hand, the use of plasticizers for HIPS and PVA exhibited positive consequences in drug solubility and rheologic behavior, probably improving sample printability. Thus, the optimization of the FDM 3D printing based on preformulation studies can assist the choice of compatible components and seek suitable processing conditions to obtain pharmaceutical products.