Effects of surface glazing on the mechanical and biological properties of 3D printed permanent dental resin materials

Purpose This study aimed to determine the surface glazing effect on the mechanical and biological properties of three-dimensional printed dental permanent resins.Methods Specimens were prepared using Formlabs, Graphy Tera Harz permanent, and NextDent C&B temporary crown resins. Specimens were divided into three groups: samples with untreated surfaces, glazed surfaces, and sand-glazed surfaces. The flexural strength, Vickers hardness, color stability, and surface roughness of the samples were analyzed to identify their mechanical properties. Their cell viability and protein adsorption were analyzed to identify their biological properties.Results The flexural strength and Vickers hardness of the samples with sand glazed and glazed surfaces were significantly increased. The color change was higher for surface untreated samples than that for the samples with sand-glazed and glazed surfaces. The surface roughness of the samples with sand-glazed and glazed surfaces was low. The samples with sand-glazed and glazed surfaces have low protein adsorption ability and high cell viability.Conclusions Surface glazing increased the mechanical strength, color stability, and cell compatibility, while reducing the Ra and protein adsorption of 3D-printed dental resins. Thus, a glazed surface exhibited a positive effect on the mechanical and biological properties of 3D-printed resins.

Fully automatic integration of dental CBCT images and full-arch intraoral impressions with stitching error correction via individual tooth segmentation and identification

We present a fully automated method of integrating intraoral scan (IOS) and dental cone-beam computerized tomography (CBCT) images into one image by complementing each image's weaknesses. Dental CBCT alone may not be able to delineate precise details of the tooth surface due to limited image resolution and various CBCT artifacts, including metal-induced artifacts. IOS is very accurate for the scanning of narrow areas, but it produces cumulative stitching errors during full-arch scanning. The proposed method is intended not only to compensate the low-quality of CBCT-derived tooth surfaces with IOS, but also to correct the cumulative stitching errors of IOS across the entire dental arch. Moreover, the integration provides both gingival structure of IOS and tooth roots of CBCT in one image. The proposed fully automated method consists of four parts; (i) individual tooth segmentation and identification module for IOS data (TSIM-IOS); (ii) individual tooth segmentation and identification module for CBCT data (TSIM-CBCT); (iii) global-to-local tooth registration between IOS and CBCT; and (iv) stitching error correction for full-arch IOS. The experimental results show that the proposed method achieved landmark and surface distance errors of 112.4μm and 301.7μm, respectively.

Influence of hydrothermal aging on the shear bond strength of 3D printed denture-base resin to different relining materials

OBJECTIVES

This study evaluated the repairability of three-dimensional printed (3DP) denture bases based on different conventional relining materials and aging.

MATERIAL AND METHODS

The groups for surface characterization (surface-roughness and contact-angle measurements) were divided based on the denture base and surface treatment. Shear bond strength test and failure-mode analysis were conducted by a combination of three variables: denture base, relining materials, and hydrothermal aging (HA). The initial characterization involved quantifying the surface roughness (n = 10) and contact angle (n = 10) of denture base specimens with and without sandblasting (SB) treatment. Four relining materials (Kooliner [K], Vertex Self-Curing [V], Tokuyama Rebase II (Normal) [T], and Ufi Gel Hard [U]) were applied to 3DP, heat-cured (HC), and self-cured (SC) denture-base resin specimens. Shear bond strength (n = 15) and failure-mode analyses (n = 15) were performed before and after HA, along with evaluations of the fractured surfaces (n = 4). Statistical analyses were performed using a two-way analysis of variance (ANOVA) for surface characterization, and a three-way ANOVA was conducted for shear bond strength.

RESULTS

The surface roughness peaked in HC groups and increased after SB. The 3DP group displayed significantly lower contact angles, which increased after treatment, similar to the surface roughness. The shear bond strength was significantly lower for 3DP and HC denture bases than for SC denture bases, and peaked for U at 10.65 ± 1.88 MPa (mean ± SD). HA decreased the shear bond strength relative to untreated samples. Furthermore, 3DP, HC, and SC mainly showed mixed or cohesive failures with V, T, and U. K, on the other hand, trended toward adhesive failures when bonded with HC and SC.

CONCLUSION

This study has validated the repairability of 3DP dentures through relining them with common materials used in clinical practice. The repairability of the 3DP denture base was on par with that of conventional materials, but it decreased after aging. Notably, U, which had a postadhesive application, proved to be the most effective material for repairing 3DP dentures.

Sulforaphane Mitigates High-Fat Diet-Induced Obesity by Enhancing Mitochondrial Biogenesis in Skeletal Muscle via the HDAC8-PGC1α Axis

SCOPE

Histone deacetylases (HDACs) play a crucial role in the transcriptional regulation of various genes which can contribute to metabolic disorders. Although sulforaphane (SFN), a natural HDAC inhibitor, has been reported to alleviate obesity in humans and mice, the specific mechanisms and how HDACs contribute to SFN's anti-obesity effects remain unclear.

METHODS AND RESULTS

Oral administration of SFN in mice fed high-fat diet increases peroxisome proliferator activating receptor γ coactivator (PGC1α)-induced mitochondrial biogenesis in skeletal muscle. Among HDACs, SFN specifically inhibits HDAC8 activity. SFN enhances mitochondrial DNA and adenosine triphosphate (ATP) production in C2C12 myotubes, similar to the action of PCI34051, a synthetic HDAC8-specific inhibitor. These effects are mediated by increased expression of PGC1α via upregulation of cAMP response element binding (CREB, Ser133 ) phosphorylation and p53 (Lys379 ) acetylation. These SFN-induced effects are not observed in cells with a genetic deletion of HDAC8, suggesting the existence of a regulatory loop between HDAC8 and PGC1α in SFN's action.

CONCLUSION

SFN prevents obesity-related metabolic dysregulation by enhancing mitochondrial biogenesis and function via targeting the HDAC8-PGCα axis. These results suggest SFN as a beneficial anti-obesity agent providing new insight into the role of HDAC8 in the PGC1α-mediated mitochondrial biogenesis, which may be a novel and promising drug target for metabolic diseases.

Deep learning and clustering approaches for dental implant size classification based on periapical radiographs

This study investigated two artificial intelligence (AI) methods for automatically classifying dental implant diameter and length based on periapical radiographs. The first method, deep learning (DL), involved utilizing the pre-trained VGG16 model and adjusting the fine-tuning degree to analyze image data obtained from periapical radiographs. The second method, clustering analysis, was accomplished by analyzing the implant-specific feature vector derived from three key points coordinates of the dental implant using the k-means++ algorithm and adjusting the weight of the feature vector. DL and clustering model classified dental implant size into nine groups. The performance metrics of AI models were accuracy, sensitivity, specificity, F1-score, positive predictive value, negative predictive value, and area under the receiver operating characteristic curve (AUC-ROC). The final DL model yielded performances above 0.994, 0.950, 0.994, 0.974, 0.952, 0.994, and 0.975, respectively, and the final clustering model yielded performances above 0.983, 0.900, 0.988, 0.923, 0.909, 0.988, and 0.947, respectively. When comparing the AI model before tuning and the final AI model, statistically significant performance improvements were observed in six out of nine groups for DL models and four out of nine groups for clustering models based on AUC-ROC. Two AI models showed reliable classification performances. For clinical applications, AI models require validation on various multicenter data.

Differentiation between Chondrosarcoma and Synovial Chondromatosis of the Temporomandibular Joint Using CT and MR Imaging

BACKGROUND AND PURPOSE

Chondrosarcoma and synovial chondromatosis of the temporomandibular joint share overlapping clinical and histopathologic features. We aimed to identify CT and MR imaging features to differentiate chondrosarcoma from synovial chondromatosis of the temporomandibular joint.

MATERIALS AND METHODS

The CT and MR images of 12 and 35 patients with histopathologically confirmed chondrosarcoma and synovial chondromatosis of the temporomandibular joint, respectively, were retrospectively reviewed. Imaging features including lesion size, center, enhancement, destruction/sclerosis of surrounding bone, infiltration into the tendon of the lateral pterygoid muscle, calcification, periosteal reaction, and osteophyte formation were assessed. A comparison between chondrosarcoma and synovial chondromatosis was performed with a Student t test for quantitative variables and the Fisher exact test or linear-by-linear association test for qualitative variables. Receiver operating characteristic analysis was performed to determine the diagnostic performance for differentiation of chondrosarcoma and synovial chondromatosis based on a composite score obtained by assigning 1 point for each of 9 imaging features.

RESULTS

High-risk imaging features for chondrosarcoma were the following: lesion centered on the mandibular condyle, destruction of the mandibular condyle, no destruction/sclerosis of the articular eminence/glenoid fossa, infiltration into the tendon of the lateral pterygoid muscle, absent or stippled calcification, periosteal reaction, internal enhancement, and size of ≥30.5 mm. The best cutoff value to discriminate chondrosarcoma from synovial chondromatosis was the presence of any 4 of these high-risk imaging features, with an area under the curve of 0.986 and an accuracy of 95.8%.

CONCLUSIONS

CT and MR imaging features can distinguish chondrosarcoma from synovial chondromatosis of the temporomandibular joint with improved diagnostic performance when a subcombination of 9 imaging features is used.

A prospective multicenter clinical study on the efficiency of detachable ball- and spring-retained implant prosthesis

PURPOSE

This prospective clinical study was conducted to evaluate the clinical usefulness of the freely detachable zirconia ball- and spring-retained implant prosthesis (BSRP) through a comparative analysis of screw- and cement-retained implant prosthesis (SCRP).

MATERIALS AND METHODS

A multi-center, randomized, prospective clinical study evaluating the clinical usefulness of the detachable zirconia ball- and spring-retained implant prostheses was conducted. Sixty-four implant prostheses in 64 patients were examined. Periodic observational studies were conducted at 0, 3, 6, and 12 months after delivery of the implant prosthesis. Factors such as implant success rate, marginal bone resorption, periodontal pocket depth, plaque and bleeding index, and prosthetic complications were evaluated, respectively.

RESULTS

During the 1-year observation period, all implants survived without functional problems and clinical mobility, showing a 100% implant success rate. Marginal bone resorption was significantly higher in the SCRP group than in the BSRP group only at the time of implant prosthesis delivery (P = .043). In all observation periods, periodontal pocket depth was slightly higher in the BSRP group than in the SCRP group, but there was no significant difference (P > .05). The modified plaque index (mPI) scores of both groups were moderate. Higher ratio of a score 2 in modified sulcus bleeding index (mBI) was observed in the BSRP group in the 6- and 12-months observation.

CONCLUSION

Within the limitations of this study, the newly developed zirconia ball- and spring-retained implant prosthesis could be considered as an applicable and predictable treatment method along with the existing screw- and cement-retained prosthesis.

Enhanced Bone Formation by Rapidly Formed Bony Wall over the Bone Defect Using Dual Growth Factors

BACKGROUND

In guided bone regeneration (GBR), there are various problems that occur in the bone defect after the wound healing period. This study aimed to investigate the enhancement of the osteogenic ability of the dual scaffold complex and identify the appropriate concentration of growth factors (GF) for new bone formation based on the novel GBR concept that is applying rapid bone forming GFs to the membrane outside of the bone defect.

METHODS

Four bone defects with a diameter of 8 mm were formed in the calvaria of New Zealand white rabbits each to perform GBR. Collagen membrane and biphasic calcium phosphate (BCP) were applied to the bone defects with the four different concetration of BMP-2 or FGF-2. After 2, 4, and 8 weeks of healing, histological, histomorphometric, and immunohistochemical analyses were conducted.

RESULTS

In the histological analysis, continuous forms of new bones were observed in the upper part of bone defect in the experimental groups, whereas no continuous forms were observed in the control group. In the histomorphometry, The group to which BMP-2 0.5 mg/ml and FGF-2 1.0 mg/ml was applied showed statistically significantly higher new bone formation. Also, the new bone formation according to the healing period was statistically significantly higher at 8 weeks than at 2, 4 weeks.

CONCLUSION

The novel GBR method in which BMP-2, newly proposed in this study, is applied to the membrane is effective for bone regeneration. In addition, the dual scaffold complex is quantitatively and qualitatively advantageous for bone regeneration and bone maintenance over time.

Effects of washing solution temperature on the biocompatibility and mechanical properties of 3D-Printed dental resin material

The use of digital manufacturing, particularly additive manufacturing using three-dimensional (3D) printing, is expanding in the field of dentistry. 3D-printed resin appliances must undergo an essential process, post-washing, to remove residual monomers; however, the effect of the washing solution temperature on the biocompatibility and mechanical properties remains unclear. Therefore, we processed 3D-printed resin samples under different post-washing temperatures (without temperature control (N/T), 30 °C, 40 °C, and 50 °C) for different durations (5, 10, 15, 30, and 60 min) and evaluated the degree of conversion rate, cell viability, flexural strength, and Vickers hardness. Increasing the washing solution temperature significantly improved the degree of conversion rate and cell viability. Conversely, increasing the solution temperature and time decreased the flexural strength and microhardness. This study confirmed that the washing temperature and time influence the mechanical and biological properties of the 3D-printed resin. Washing 3D-printed resin at 30 °C for 30 min was most efficient to maintain optimal biocompatibility and minimize changes of mechanical properties.

Higenamine Reduces Fine-Dust-Induced Matrix Metalloproteinase (MMP)-1 in Human Keratinocytes

Environmental pollutants such as fine dust are increasingly linked to premature skin aging. In this study, we investigated the protective effects of higenamine, a natural plant alkaloid, against fine-dust-induced skin aging in human keratinocytes (HaCaT cells). We found that higenamine significantly attenuated fine-dust-induced expression of matrix metalloproteinase-1 (MMP-1), a key enzyme involved in collagen degradation. Furthermore, higenamine was found to modulate fine-dust-induced AP-1 and NF-κB transactivation, which are crucial factors for MMP-1 transcription. Higenamine also impeded fine-dust-induced phosphorylation in specific pathways related to AP-1 and NF-κB activation, and effectively alleviated reactive oxygen species (ROS) production, a key factor in oxidative stress caused by fine dust exposure. These results suggest that higenamine exerts protective effects against fine-dust-induced skin aging, primarily through its MMP-1 inhibitory properties and ability to mitigate ROS-induced oxidative damage. Our data highlight the potential of higenamine as an effective ingredient in skincare products designed to combat environmental skin damage.

Safety and efficacy of trastuzumab biosimilar plus irinotecan or gemcitabine in patients with previously treated HER2 (ERBB2)-positive non-breast/non-gastric solid tumors: a phase II basket trial with circulating tumor DNA analysis

BACKGROUND

Human epidermal growth factor receptor 2 (HER2) (ERBB2)-directed agents are standard treatments for patients with HER2-positive breast and gastric cancer. Herein, we report the results of an open-label, single-center, phase II basket trial to investigate the efficacy and safety of trastuzumab biosimilar (Samfenet®) plus treatment of physician's choice for patients with previously treated HER2-positive advanced solid tumors, along with biomarker analysis employing circulating tumor DNA (ctDNA) sequencing.

METHODS

Patients with HER2-positive unresectable or metastatic non-breast, non-gastric solid tumors who failed at least one prior treatment were included in this study conducted at Asan Medical Center, Seoul, Korea. Patients received trastuzumab combined with irinotecan or gemcitabine at the treating physicians' discretion. The primary endpoint was the objective response rate as per RECIST version 1.1. Plasma samples were collected at baseline and at the time of disease progression for ctDNA analysis.

RESULTS

Twenty-three patients were screened from 31 December 2019 to 17 September 2021, and 20 were enrolled in this study. Their median age was 64 years (30-84 years), and 13 patients (65.0%) were male. The most common primary tumor was hepatobiliary cancer (seven patients, 35.0%), followed by colorectal cancer (six patients, 30.0%). Among 18 patients with an available response evaluation, the objective response rate was 11.1% (95% confidence interval 3.1% to 32.8%). ERBB2 amplification was detected from ctDNA analysis of baseline plasma samples in 85% of patients (n = 17), and the ERBB2 copy number from ctDNA analysis showed a significant correlation with the results from tissue sequencing. Among 16 patients with post-progression ctDNA analysis, 7 (43.8%) developed new alterations. None of the patients discontinued the study due to adverse events.

CONCLUSIONS

Trastuzumab plus irinotecan or gemcitabine was safe and feasible for patients with previously treated HER2-positive advanced solid tumors with modest efficacy outcomes, and ctDNA analysis was useful for detecting HER2 amplification.

A comprehensive study on the mechanical effects of implant-supported prostheses under multi-directional loading and different occlusal contact points

AIMS

To evaluate screw loosening and fracture load and angular deviation of a single implant-supported prosthesis under multi-directional loading condition at three different occlusal contact points.

METHODS

A total of 40 metal crowns were cemented to external connection implants and were embedded vertically and obliquely. The occlusal surface of the crown was designed with three flat surfaces, contact a, b, and c, representing outer and inner 20-degree inclination for buccal and lingual cusps. The angular deviations of implant crown under static 50N of loading were measured. And screw removal torque was evaluated before and after 57,600 load cycles. Then, fracture load was measured for each specimen. Data analysis was performed using one-way analysis of variance test of significance followed by Tukey honest significant difference (HSD) test(p < 0.05).

RESULTS

Angular deviation results showed statistical significance between all contact points in vertically embedded group compared to obliquely embedded group, which showed similar results between contact A and B compared to C. In the other hand, screw loosening evaluation did not show statistical significance among the tested groups. And for the fracture load evaluation the maximum values reached twice the yield values in all contact areas.

CONCLUSIONS

Mechanical effects were different regarding to diverse loading direction and contact points. The results of this study suggest that the stress concentration might increase in unfavorable vector direction.

Piezocatalytic 2D WS2 Nanosheets for Ultrasound-Triggered and Mitochondria-Targeted Piezodynamic Cancer Therapy Synergized with Energy Metabolism-Targeted Chemotherapy

Piezoelectric nanomaterials that can generate reactive oxygen species (ROS) by piezoelectric polarization under an external mechanical force have emerged as an effective platform for cancer therapy. In this study, piezoelectric 2D WS₂ nanosheets are functionalized with mitochondria-targeting triphenylphosphonium (TPP) for ultrasound (US)-triggered, mitochondria-targeted piezodynamic cancer therapy. In addition, a glycolysis inhibitor (FX11) that can inhibit cellular energy metabolism is loaded into TPP- and poly(ethylene glycol) (PEG)-conjugated WS₂ nanosheet (TPEG-WS₂ ) to potentiate its therapeutic efficacy. Upon US irradiation, the sono-excited electrons and holes generated in the WS₂ are efficiently separated by piezoelectric polarization, which subsequently promotes the production of ROS. FX11-loaded TPEG-WS₂ (FX11@TPEG-WS₂ ) selectively accumulates in the mitochondria of human breast cancer cells. In addition, FX11@TPEG-WS₂ effectively inhibits the production of adenosine triphosphate . Thus, FX11@TPEG-WS₂ exhibits outstanding anticancer effects under US irradiation. An in vivo study using tumor-xenograft mice demonstrates that FX11@TPEG-WS₂ effectively accumulated in the tumors. Its tumor accumulation is visualized using in vivo computed tomography . Notably, FX11@TPEG-WS₂ with US irradiation remarkably suppresses the tumor growth of mice without systemic toxicity. This study demonstrates that the combination of piezodynamic therapy and energy metabolism-targeted chemotherapy using mitochondria-targeting 2D WS₂ is a novel strategy for the selective and effective treatment of tumors.

Improving Bone Formation by Guided Bone Regeneration Using a Collagen Membrane with rhBMP-2: A Novel Concept

We examined whether recombinant human bone morphogenetic protein-2 (rhBMP-2) when applied to collagen membranes, would reinforce them during guided bone regeneration. Four critical cranial bone defects were created and treated in 30 New Zealand white rabbits, including a control group, critical defect only; group 1, collagen membrane only; group 2, biphasic calcium phosphate (BCP) only; group 3, collagen membrane + BCP; group 4, collagen membrane with rhBMP-2 (1.0 mg/mL); group 5, collagen membrane with rhBMP-2 (0.5 mg/mL); group 6, collagen membrane with rhBMP-2 (1.0 mg/mL) + BCP; and group 7, collagen membrane with rhBMP-2 (0.5 mg/mL) + BCP. After a 2-, 4-, or 8-week healing period, the animals were sacrificed. The combination of collagen membranes with rhBMP-2 and BCP yielded significantly higher bone formation rates compared to the other groups (control group and groups 1-5 < groups 6 and 7; p < 0.05). A 2-week healing period yielded significantly lower bone formation than that at 4 and 8 weeks (2 < 4 = 8 weeks; p < 0.05). This study proposes a novel GBR concept in which rhBMP-2 is applied to collagen membranes outside instead of inside the grafted area, thereby inducing quantitatively and qualitatively enhanced bone regeneration in critical bone defects.

Orobol, 3'-hydroxy-genistein, suppresses the development and regrowth of cutaneous SCC

Chronic solar ultraviolet exposure is a major risk factor for cutaneous squamous cell carcinoma (cSCC), which is the second most common type of skin cancer. Our previous data showed that total protein and phosphorylation levels of T-LAK cell-originated protein kinase (TOPK) were enhanced in solar-simulated light (SSL)-induced skin carcinogenesis and overexpressed in actinic keratosis (AK) and cSCC human skin tissues compared to those in matched normal skin. Thus, targeting TOPK activity could be a helpful approach for treating cSCC. Our data showed that orobol directly binds to TOPK in an ATP-independent manner and inhibits TOPK kinase activity. Furthermore, orobol inhibited anchorage-independent colony formation by SCC12 cells in a dose-dependent manner. After discontinuing the treatment, patients commonly return to tumor-bearing conditions; therefore, therapy or intermittent dosing of drugs must be continued indefinitely. Thus, to examine the efficacy of orobol against the development and regrowth of cSCC, we established mouse models including prevention, and therapeutic models on the chronic SSL-irradiated SKH-1 hairless mice. Early treatment with orobol attenuates chronic SSL-induced cSCC development. Furthermore, orobol showed therapeutic efficacy after the formation of chronic SSL irradiation-induced tumor. In the mouse model with intermittent dosing of orobol, our data showed that re-application of orobol is effective for reducing tumor regrowth after discontinuation of treatment. Moreover, oncogenic protein levels were significantly attenuated by orobol treatment in the SSL-stimulated human skin. Thus, we suggest that orobol, as a promising TOPK inhibitor, could have an effective clinical approach to prevent and treat the development and regrowth of cSCC.

Preoperative Chemoradiotherapy With Capecitabine With or Without Temozolomide in Patients With Locally Advanced Rectal Cancer: A Prospective, Randomised Phase II Study Stratified by O6-Methylguanine DNA Methyltransferase Status: KCSG-CO17-02

AIMS

To evaluate the clinical efficacy of adding temozolomide (TMZ) to preoperative capecitabine (CAP)-based chemoradiotherapy in patients with locally advanced rectal cancer (LARC) and validate O⁶-methylguanine DNA methyltransferase (MGMT) methylation status as a predictive marker for TMZ combined regimens.

MATERIALS AND METHODS

LARC patients with clinical stage II (cT3-4N0) or III (cT_anyN+) disease were enrolled. They were stratified into unmethylated MGMT (uMGMT) and methylated MGMT (mMGMT) groups by methylation-specific polymerase chain reaction before randomisation and were then randomly assigned (1:1) to one of four treatment arms: uMGMT/CAP (arm A), uMGMT/TMZ + CAP (arm B), mMGMT/CAP (arm C) and mMGMT/TMZ + CAP (arm D). The primary end point was the pathological complete response (pCR) rate.

RESULTS

Between November 2017 and July 2020, 64 patients were randomised. Slow accrual caused early study termination. After excluding four ineligible patients, 60 were included in the full analysis set. The pCR rate was 15.0% (9/60), 0%, 14.3%, 18.8% and 26.7% for the entire cohort, arms A, B, C and D, respectively (P = 0.0498 between arms A and D). The pCR rate was 9.7% in the CAP group (arms A + C), 20.7% in the TMZ + CAP group (arms B + D), 6.9% in the uMGMT group (arms A + B) and 22.6% in the mMGMT group (arms C + D). Grade 1-2 nausea or vomiting was significantly more frequent in the TMZ + CAP treatment groups (arms B + D) than in the CAP treatment groups (arms A + C, P < 0.001) with no difference in grade 3 adverse events. There were no grade 4 or 5 adverse events.

CONCLUSION

The addition of TMZ to CAP-based chemoradiotherapy tended to improve pCR rates, particularly in those with mMGMT LARC. MGMT status may warrant further investigation as a predictive biomarker for chemotherapeutic agents and radiotherapy.

Effects of heat-treatment methods on cytocompatibility and mechanical properties of dental products 3D-printed using photopolymerized resin

PURPOSE

The purpose of this study was to test heat-treatment methods for improving the cytocompatibility of dental 3D printable photopolymer resins.

METHODS

Nextdent C&B resin and a digital light processing 3D printer were used to print all specimens, which were divided into seven groups as follows: 1-month storage at controlled room temperature, 20 to 25 °C (RT), 24-hour storage at RT, 24-hour storage in RT water, 1-min immersion in 80 °C water, 1-min immersion in 100 °C water, 5-min immersion in 100 °C water, and autoclaving. Cell viability tests, cytotoxicity tests, and confocal laser scanning microscopy were performed to analyze the cytocompatibility of the 3D-printed resin. Fourier-transform infrared spectroscopy was performed after heat-treatment to determine the degree of conversion (DC).

RESULTS

Immersing printed resin samples in 100 °C water for 1 or 5 min after the curing process was an effective method for increasing cytocompatibility by inducing the preleaching of toxic substances such as unpolymerized monomers, photoinitiators, and additives. Moreover, the DC can be increased by additional polymerization without affecting the mechanical properties of the material.

CONCLUSIONS

Immersing the printed photosensitive dental resins in 100 °C water for 5 min is a suitable method for increasing cytocompatibility and the DC.

Evaluation of the color stability of 3D printed resin according to the oxygen inhibition effect and temperature difference in the post-polymerization process

The aim of this study was to determine the color stability of 3D printed resin according to the post-curing conditions (polymerization conditions and temperature). Specimens were post-polymerized under different conditions of oxygen inhibition, such as on glycerin immersion (GLY), medium-low vacuum environment (VA), and oxygen contact (CON, the control group), and temperature (35 °C, 60 °C, and 80 °C). The degree of conversion (DC), water sorption (Wsp) and solubility (Wsl), surface roughness (Ra) were measured. Additionally, surface free energy (SFE), pH values of colorants were measured. Grape juice (grape), coffee, and curry were used as the colorants, and distilled water (DW) was used as a control. And the color value was measured before and after immersion using a spectrophotometer. Then, Calculated the color change. For statistical methods, The Shapiro-Wilk test performed to check for normality revealed that the data presented a normal distribution (p>0.05). ΔE values were analyzed using three-way ANOVA. DC, Wsp, Wsl, SFE, and Ra were analyzed using two-way ANOVA. To confirm the linear correlation, Pearson's correlation coefficient was determined. The threshold for significance (p) was set at 0.05 (95% confidence interval) for all tests. DC was the highest at 80 °C in the GLY group (95.08 ± 4.88%). And Wsl decreased with increasing temperature, and was lowest at 80 °C in the GLY group (0.46 ± 0.30 um/mm3). After the colorants were immersed for 30 days, as the temperature increased, ΔE decreased in the GLY group but not in the VA and CON groups, and was the lowest at 80 °C in the GLY group: (DW, 0.95 ± 0.45 [mean± SD]; grape, 6.45± 0.69; coffee, 4.50± 0.56; curry, 9.37± 1.40). There was also a significant inverse relation between DC and ΔE. A significant inverse relation was found between Wsl and DC, and a significant positive correlation was found between Wsl and ΔE. Wsp, SFE, and Ra did not affect color stability. In the post-polymerization process, increasing the temperature and GLY were effective in reducing ΔE, which was lowest at 80 °C in the GLY group. It was also observed that a complex mechanism between the DC, Wsl of 3D printed resin affects ΔE of the resin.

Antimicrobial Activity of Smilax china L. Root Extracts against the Acne-Causing Bacterium, Cutibacterium acnes, and Its Active Compounds

The root of Smilax china L. is used in traditional Korean medicine. We found that the Smilax china L. root extract has strong antimicrobial activity against two Cutibacterium acnes strains (KCTC 3314 and KCTC 3320). The aim of this study was to identify the beneficial properties of Smilax china L. extracts for their potential use as active ingredients in cosmetics for the treatment of human skin acne. The high-performance liquid chromatography (HPLC) and liquid chromatography-hybrid quadrupole time-of-flight mass spectrometry (LC/QTOF/MS) methods were used to obtain the profile of secondary metabolites from the ethyl acetate-soluble fraction of the crude extract. Agar diffusion and resazurin-based broth microdilution assays were used to evaluate antimicrobial activity and minimum inhibitory concentrations (MIC), respectively. Among the 24 metabolites, quercetin, resveratrol, and oxyresveratrol were the most potent compounds against Cutibacterium acnes. Minimum inhibitory concentrations of quercetin, resveratrol, and oxyresveratrol were 31.25, 125, and 250 μg/mL, respectively.

Sulforaphene Attenuates Cutibacterium acnes-Induced Inflammation

Acne is a chronic inflammatory disease of the sebaceous gland attached to the hair follicles. Cutibacterium acnes is a major cause of inflammation caused by acne. It is well known that C. acnes secretes a lipolytic enzyme to break down lipids in sebum, and free fatty acids produced at this time accelerate the inflammatory reaction. There are several drugs used to treat acne; however, each one has various side effects. According to previous studies, sulforaphene (SFEN) has several functions associated with lipid metabolism, brain function, and antibacterial and anti-inflammatory activities. In this study, we examined the effects of SFEN on bacterial growth and inflammatory cytokine production induced by C. acnes. The results revealed that SFEN reduced the growth of C. acnes and inhibited proinflammatory cytokines in C. acnes-treated HaCaT keratinocytes through inhibiting NF-κB-related pathways. In addition, SFEN regulated the expression level of IL-1α, a representative pro-inflammatory cytokine expressed in co-cultured HaCaT keratinocytes and THP-1 monocytes induced by C. acnes. In conclusion, SFEN showed antibacterial activity against C. acnes and controlled the inflammatory response on keratinocytes and monocytes. This finding means that SFEN has potential as both a cosmetic material for acne prevention and a pharmaceutical material for acne treatment.

Effects of Post-Curing Light Intensity on the Mechanical Properties and Three-Dimensional Printing Accuracy of Interim Dental Material

This study evaluated the effects of the light intensity of curing and the post-curing duration on the mechanical properties and accuracy of the interim dental material. After designing the specimen, 3D printing was performed, and the light intensity was divided into groups G20, G60, G80, and G120 (corresponding to 1.4−1.6, 2.2−3.0, 3.8−4.4, and 6.4−7.0 mW/cm2, respectively), with no post-curing or 5, 10, or 20 min of post-curing being performed. The flexural properties, Vickers microhardness, degree of conversion (DC), and 3D accuracy were then evaluated. The flexural properties and Vickers microhardness showed a sharp increase at the beginning of the post-curing and then tended to increase gradually as the light intensity and post-curing time increased (p < 0.001). On the other hand, there was no significant difference between groups in the accuracy analysis of a 3D-printed three-unit bridge. These results indicate that the light intensity of the post-curing equipment influences the final mechanical properties of 3D-printed resin and that post-curing can be made more efficient by optimizing the light intensity and post-curing time.

Accuracy of 3D printed models and implant-analog positions according to the implant-analog-holder offset, inner structure, and printing layer thickness: an in-vitro study

PURPOSE

This study aimed to determine how the implant-analog-holder (IAH) offset, inner structure, and printing layer thickness influence the overall accuracy and local implant-analog positional changes of 3D printed dental models.

METHODS

Specimens in 12 experimental groups (8 specimens per group) with different IAH offsets, inner structures, and printing layer thicknesses were printed in three dimensions using an LCD printer (Phrozen Shuffle) and digitized by a laboratory scanner (Identica T500). The trueness and precision of the printed model as well as the angular distortion, depth deviation, and linear distortion of the implant analog were evaluated using three-way ANOVA.

RESULTS

The positional accuracy was significantly higher for IAH offsets of 0.04 mm and 0.06 mm than for one of 0.08 mm, for a hollow than a solid inner structure, and for a printing layer thickness of 100 µm than for one of 50 µm (all P<.001).

CONCLUSIONS

The accuracies of the 3D printed models and the implant-analog positions were significantly affected by the IAH offset, inner structure, and printing layer thickness.

CLINICAL SIGNIFICANCE

Given the observation of this study, premeditating the IAH offset of 0.06 mm, hollow inner structure, and printing layer thickness of 100 µm before printing can help clinicians reach the optimum overall printing accuracy and minimum the local positional changes of the implant-analogs.

Low muscle mass, low muscle function, and sarcopenia in the urban and rural elderly

Health outcomes of the elderly vary between rural and urban areas. Sarcopenia is diagnosed as loss of muscle strength or impaired physical performance, namely "low muscle function" and low muscle mass. Outcomes of low muscle mass and low muscle function are not equal. This study aimed to investigate the prevalence of low muscle mass, low muscle function, and sarcopenia in rural and urban populations and to determine whether regional differences were associated with each of these components. Participants aged ≥ 69 years (n = 2354) were recruited from three urban districts and one rural district in Korea. Low muscle mass was defined by appendicular lean mass using bioelectrical impedance analysis. Low muscle function was defined by handgrip strength and 5-chair stand test. Sarcopenia was defined as low muscle mass plus low muscle function. The prevalence of low muscle function (53.7% vs. 72.8%), and sarcopenia (16.3% vs. 24.4%) were higher in the rural elderly population. Rural residence was associated with low muscle function (OR 1.63; 95% CI 1.13-2.37, P = 0.009), but not with low muscle mass (OR 0.58; 95% CI 0.22-1.54, P = 0.271) or with sarcopenia (OR 1.13; 95% CI 0.63-2.00, P = 0.683). Interventions to detect and improve low muscle function in rural elderly population are needed.

Effect of air abrasion, acid etching, and aging on the shear bond strength with resin cement to 3Y-TZP zirconia

This study investigates the effect of acid etching treatment on the surface microstructure, surface roughness, and surface contact angle of zirconia and compares the effects of air abrasion, different etching times, and aging on the shear bond strength (SBS) of resin cement on the zirconia surface. 480 specimens (9 × 10 × 10 mm) were divided into as-sintered and air-abraded groups, and each group was further subdivided into six groups based on etching time (0, 3, 5, 10, 20, and 30 min). The etching solution comprised hydrofluoric acid 25%, sulfuric acid 16%, hydrogen peroxide, methyl alcohol, and purified water. The shear bond strength (SBS), scanning electron microscopy, surface roughness, contact angle, and failure mode were measured. The results indicated that the mean SBS values increased and decreased significantly when the etching times increased to 20 min and 30 min, respectively, in both groups. Further, SBS after aging was lower than that before aging in all groups. Sandblasting, etching time, and aging all showed significant effects (p < 0.001) in the three-way analysis of variance. In addition, the surface roughness increased and the contact angle decreased significantly with an increase in etching time. Thus, the acid-etching treatment induced significant changes on the zirconia surface and increased the SBS of the resin cement. The results of this in vitro study suggest that acid etching is a promising alternative for zirconia surface treatment.

Piceatannol, a metabolite of resveratrol, attenuates atopic dermatitis by targeting Janus kinase 1

BACKGROUND

Piceatannol is a resveratrol metabolite commonly found in red wine, grapes. Several studies have investigated the immune-modulating effects of piceatannol on processes related to allergic reactions. However, the relationship between piceatannol and atopic dermatitis (AD) has not yet been reported. This study sought to investigate the effects of piceatannol in animal and cell line models.

METHODS

AD-like symptoms and skin lesions were triggered by repeated topical treatment of Dermatophagoides farinae extract (DFE) on the skin of NC/Nga mice. The molecular mechanism of piceatannol was studied in the TNFα/IFNγ-induced HaCaT cell line.

RESULTS

Piceatannol attenuated DFE-induced AD-like symptoms, as shown by skin thickness, dermatitis score, scratching time, and skin water loss. Histopathological analysis showed that piceatannol suppressed DFE-induced immune cell infiltration into the skin. These results occurred concomitantly with the downregulation of inflammatory markers, including serum and skin TARC and MDC. Piceatannol decreased phosphorylation of JAK-STAT protein in the TNFα/IFNγ-induced HaCaT cell line. A molecular docking study showed that piceatannol strongly interacts with JAK1, suggesting a possible mode of action.

CONCLUSION

The study results showed that piceatannol, a metabolite of resveratrol, attenuates atopic dermatitis and provide important implication of development of piceatannol as functional ingredients or therapeutic agents.

Orobol from enzyme biotransformation attenuates Dermatophagoides farinae-induced atopic dermatitis-like symptoms in NC/Nga mice

Orobol, a metabolite of genistein, is rare in natural soybean. Several studies have revealed the immune-controlling effects of orobol on inflammatory diseases. Furthermore, a few studies have demonstrated that orobol decreases pro-inflammatory compounds resulting in the alleviation of allergic reactions. However, the relationship between orobol and atopic dermatitis (AD) in animal models has not been revealed. Therefore, we sought to investigate the effects of orobol on AD-like symptoms. AD-like symptoms and skin lesions were induced by repeated topical application of Dermatophagoides farinae extract (DFE) on the skin of NC/Nga mice. Topical application of orobol attenuated DFE-induced AD-like symptoms and transepidermal water loss and increased skin hydration. Histopathological analysis revealed that orobol alleviated DFE-induced eosinophil and mast cell infiltration into the skin. These observations occurred concomitantly with the downregulation of inflammatory markers including serum TARC, MDC, and IgE. In addition, orobol alleviated dorsal Th2 cytokines such as IL-4 and IL-13. Pre-treatment of orobol decreased the activity of the MAPKs and NF-κB signalling cascade in the TNFα/IFNγ-induced HaCaT cell line. These results suggest that orobol, a natural dietary isoflavone, has therapeutic efficacy for the prevention and treatment of AD.

High-precision measurement of the W boson mass with the CDF II detector

The mass of the W boson, a mediator of the weak force between elementary particles, is tightly constrained by the symmetries of the standard model of particle physics. The Higgs boson was the last missing component of the model. After observation of the Higgs boson, a measurement of the W boson mass provides a stringent test of the model. We measure the W boson mass, M_W, using data corresponding to 8.8 inverse femtobarns of integrated luminosity collected in proton-antiproton collisions at a 1.96 tera-electron volt center-of-mass energy with the CDF II detector at the Fermilab Tevatron collider. A sample of approximately 4 million W boson candidates is used to obtain [Formula: see text], the precision of which exceeds that of all previous measurements combined (stat, statistical uncertainty; syst, systematic uncertainty; MeV, mega-electron volts; c, speed of light in a vacuum). This measurement is in significant tension with the standard model expectation.

Inhibitory Effect of Lotusine on Solar UV-Induced Matrix Metalloproteinase-1 Expression

Solar ultraviolet (sUV) radiation remains a major cause of skin aging. Nelumbo nucifera (lotus) is a well-known edible plant widely grown in Asia, including Korea, China, and Japan. The lotus consists of flowers, leaves, stems, and seeds, and all parts reportedly possess nutritional and medical values. Traditionally, lotus flowers, leaves, stems, and seeds have been used as antidiarrheal agents, diuretics, antipyretics, and antimicrobial and antihyperlipidemic agents. In addition, the Nelumbo nucifera lotus embryo has been shown to possess sedative and antipyretic properties and can relieve hemostatic thirst and treat eye diseases. Recently, Nelumbo nucifera lotus flower extract has been widely used in cosmetics due to its ability to reduce wrinkles and its whitening effects. Numerous cosmetics using Nelumbo nucifera lotus embryo extracts are commercially available. However, the active components of Nelumbo nucifera remain elusive. Lotusine is a phytochemical and soluble alkaloid found in lotus embryos. Herein, we examined the anti-wrinkle effect of lotusine using sUV-exposed human keratinocytes. We observed that lotusine reduced sUV-induced matrix metalloproteinase (MMP)-1 expression and modulated transcriptional activities of activator protein (AP)-1 and nuclear factor kappa B (NF-κB). sUV-induced AP-1 and NF-κB activity could be activated via multiple signal transduction cascades, including the p38 MAPK, JNK, ERK1/2, and Akt pathways in the skin. Lotusine inhibited the MEK1/2-ERK1/2-p90^RSK, MKK3/6-p38, and Akt-p70^S6K pathways. Overall, our findings suggest that lotusine has potential benefits related to MMP-1 expression and skin aging following sUV exposure. Hence, the lotus can be developed as a valuable functional food and cosmetic material.

Influence of different postcuring parameters on mechanical properties and biocompatibility of 3D printed crown and bridge resin for temporary restorations

This study analyzed the flexural properties, Vickers hardness, degree of conversion (DC), and cell viability of 3D printed crown and bridge resin postcured using various types of postcuring equipment (PCE). 3D printed specimens were postcured for various times using different types of 3D printing PCE [for 5, 15, and 30 min using LC 3D Print Box (LC), Form Cure (FC), Cure M (CM), and Veltz 3D (VE) devices] and the VALO handheld light-curing (VA) device for 20, 40, and 60 s. Neither the flexural strength (132.27-145.79 MPa) nor the flexural modulus (1.52-1.83 GPa) differed significantly when postcuring for 30 min using the LC, FC, CM, or VE device, or for 20, 40, or 60 s of postcuring using the VA device (p > 0.05). The Vickers hardness was highest after 30 min of postcuring for all groups, and varied significantly with the postcuring time in the LC (p < 0.001) and CM (p < 0.001) groups. DC was significantly higher for the 5-min CM group (84.97 ± 4.02%) than for the GS, 30-min FC, 5-min VE, and 20-s VA groups. Cell viability of the postcured resin specimens was 56.46-92.29%, and varied significantly in the CM and VE groups according to the postcuring time (p < 0.05). Confocal laser scanning microscopy observations showed well-developed cell morphology and numerous cell-cell contacts in all groups except the GS group. This study found that the use of different types of PCE did not significantly affect the flexural properties of 3D printed crown and bridge resin, whereas there were significant variations in DC, Vickers hardness, and cell viability.

Dental students' perceptions on a simulated practice using patient-based customised typodonts during the transition from preclinical to clinical education

PURPOSE/OBJECTIVES

Dental students experience difficulties during the transition from preclinical to clinical curriculum. In order to help the students to adapt to the clinical education programme, a simulated practice using patient-based customised models was introduced in this study to prepare for their first clinical practice.

METHODS

This study included 45 third-year predoctoral students (D3 students) who were about to perform the preparation of a single crown abutment on their first patient. After practicing abutment preparation using simulated models and providing the actual treatment to their own patient, the students were surveyed to investigate their perceptions on the simulated practice using the 3D-printed customised typodont model. The statistical analysis of the quantitative data and the thematic analysis of the qualitative data were conducted.

RESULTS

Regarding this simulation, more than 80% of the students gave positive feedback on their practice of (a) operative positions and postures, (b) finger rest, (c) occlusal reduction, (d) axial reduction and (e) proximal reduction. Student responses on the open-ended questions about how they perceived the usefulness of this simulation were categorised as "First clinical case," "Patient-based model" and "Realistic simulation environment." In addition, a number of improvements of the simulation were also suggested by the students including the typodont and the manikin.

CONCLUSIONS

This study gives insights into the significance of simulated practice using patient-based customised typodonts as a transitional education tool and its direction of development in the field of restorative treatments accompanied by irreversible tooth preparations.

Optimization of the extraction process of high levels of chlorogenic acid and ginsenosides from short-term hydroponic-cultured ginseng and evaluation of the extract for the prevention of atopic dermatitis

Background

Short-term hydroponic-cultured ginseng (sHCG), which is 1-year-old ginseng seedlings cultivated for 4 weeks in a hydroponic system, is a functional food item with several biological effects. However, the optimal extraction conditions for sHCG, and the bioactivity of its extracts, have not been evaluated.

Methods

Chlorogenic acid (CGA) and ginsenoside contents were evaluated in sHCG, white ginseng (WG), and red ginseng (RG) using high-performance liquid chromatography. Response surface methodology (RSM) was used to optimize the extraction conditions (temperature and ethanol concentration) to maximize the yield of dry matter, CGA, and four ginsenosides (Re, Rg₁, Rb₁, and Rd) from sHCG. The optimal extraction conditions were applied to pilot-scale production of sHCG extracts. The expression levels of tumor necrosis factor (TNF)-α/interferon (IFN)-γ-induced thymic and activation-regulated chemokines (TARC/CCL17) were measured after treatment with sHCG, WG, and RG extracts, and the effects of their bioactive compounds (CGA and four ginsenosides) on human skin keratinocytes (HaCaTs) were evaluated.

Results

CGA and four ginsenosides, which are bioactive compounds of sHCG, significantly inhibited TNF-α/IFN-γ-induced TARC/CCL17 expression. The optimal sHCG extraction conditions predicted by the RSM models were 80 °C and 60% ethanol (v/v). The sHCG extracts produced at the pilot scale under optimal conditions greatly alleviated TNF-α/IFN-γ-induced TARC/CCL17 production compared with WG and RG extracts.

Conclusions

Pesticide-free sHCG extracts, which contain high levels of CGA and the ginsenosides Re, Rg₁, Rb₁, and Rd as bioactive compounds, may have therapeutic potential for atopic diseases.

Effects of Artificial Tooth Brushing and Hydrothermal Aging on the Mechanical Properties and Color Stability of Dental 3D Printed and CAD/CAM Materials

This study analyzed the surface roughness and waviness, Vickers hardness (VHN), and color changes of six types of 3D printed resins and computer-aided design/computer-aided manufacturing (CAD/CAM) materials after artificial toothbrushing. The average surface roughness height (Ra) change of Formlabs denture teeth A2 resin (FMLB) was not significant between after artificial toothbrushing (0.17 ± 0.02 μm and 0.17 ± 0.05 μm, respectively; mean ± standard deviation). However, the Ra value increased significantly in all remaining groups. Regarding waviness, polymethylmethacrylate (PMMA) had the largest increases in average waviness height (Wa) and maximum surface waviness height (Wz) between, before (0.43 ± 0.23 μm and 0.08 ± 0.02 μm), and after (8.67 ± 4.03 μm, 1.30 ± 0.58 μm) toothbrushing. There were no significant changes in Wa for Formlabs denture teeth A2 resin (FMLB) and NextDent C&B (NXT). After artificial toothbrushing, the dispersed-filler composite (DFC) group had the largest color difference (ΔE, of 2.4 ± 0.9), and the remaining materials had smaller changes than the clinical acceptance threshold of ΔE = 2.25. The VHN of FMLB and NXT were 9.1 ± 0.4 and 15.5 ± 0.4, respectively, and were not affected by artificial toothbrushing. The flexural strengths of the 3D printed materials were 139.4 ± 40.5 MPa and 163.9 ± 14.0 MPa for FMLB and NXT, respectively, which were similar to those of the polycarbonate and PMMA groups (155.2 ± 23.6 MPa and 108.0 ± 8.1 MPa, respectively). This study found that the evaluated 3D printed materials had mechanical and optical properties comparable to those of CAD/CAM materials and were stable even after artificial toothbrushing and hydrothermal aging.

Evaluation of Dimensional Changes According to Aging Period and Postcuring Time of 3D-Printed Denture Base Prostheses: An In Vitro Study

During the three-dimensional (3D) printing process of a dental prosthesis, using photopolymer resin, partially polymerized resin is further cured through the postcuring process that proceeds after the printing, which improves the stability of the printed product. The mechanical properties of the end product are known to be poor if the postcuring time is insufficient. Therefore, this study evaluated the effect of the postcuring time of the 3D-printed denture base on its dimensional stability, according to the aging period. The 3D prints were processed after designing maxillary and mandibular denture bases, and after the following postcuring times were applied: no postcuring, and 5, 15, 30, and 60 min. The dimensional stability change of the denture base was evaluated and analyzed for 28 days after the postcuring process. The trueness analysis indicated that the mandibular denture base had lower output accuracy than the maxillary denture base, and the dimensional stability change increased as postcuring progressed. In the no postcuring group for the mandible, the error value was 201.1 ± 5.5 µm (mean ± standard deviation) after 28 days, whereas it was 125.7 ± 13.0 µm in the 60 min postcuring group. For both the maxilla and the mandible, shorter postcuring times induced larger dimensional stability changes during the aging process. These findings indicate that in order to manufacture a denture base with dimensional stability, a sufficient postcuring process is required during the processing stage.

Pemetrexed plus cisplatin in patients with previously treated advanced sarcoma: a multicenter, single-arm, phase II trial

Background

Patients with advanced sarcomas have a poor prognosis and few treatment options that improve overall survival. We assessed the efficacy and tolerability of pemetrexed and cisplatin combination therapy in patients with refractory bone and soft tissue sarcoma (STS).

Patients and Methods

Patients were included in this multicenter, phase II study (ClinicalTrials.gov identifier NCT03809637) if they progressed after receiving one or more chemotherapy regimens containing an anthracycline and/or ifosfamide. Pemetrexed was first administered intravenously, followed by cisplatin, over a cycle of 21 days, for a maximum of six cycles. The primary endpoint was a progression-free rate (PFR) at 3 months (3-month PFR).

Results

From January 2017 to September 2019, we enrolled 37 patients; of these, 73% had previously undergone three or more rounds of chemotherapy. Five patients (13.5%) exhibited objective responses, including two patients (2/6, 33.3%) with malignant peripheral nerve sheath tumors, one patient (1/4, 25%) with synovial sarcoma, one patient (1/4, 25%) with undifferentiated pleomorphic sarcoma, and one patient (1/4, 25%) with angiosarcoma. The median progression-free survival was 2.6 months, and the 3-month PFR was 45.9% (n = 17). None of the four patients with osteosarcoma exhibited objective responses or were progression free at 3 months. The most frequent treatment-related grade 3-4 toxicities included neutropenia (16.2%), anemia (13.5%), thrombocytopenia (13.5%), and fatigue (8.1%). Among 26 patients (70.3%) available for immunohistochemical assessments, patients in the low-excision repair cross-complementation group 1 (ERCC1) and low-thymidylate synthase expression groups showed a tendency for longer overall survival.

Conclusions

Combination therapy with pemetrexed and cisplatin was associated with clinically meaningful and sustained responses among patients with advanced and refractory STS. The combination therapy met its predefined primary study endpoint.

•

Pemetrexed and cisplatin show promising efficacy for advanced sarcoma treatment, particularly as a salvage therapy option.

•

The combination therapy met its predefined primary endpoint, with a 3-month PFR of 45.9%.

•

Pemetrexed and cisplatin showed acceptable toxicity in heavily treated sarcoma patients.

Effect of Acid Mixtures on Surface Properties and Biaxial Flexural Strength of As-Sintered and Air-Abraded Zirconia

The aim of this work was to evaluate the effects of application time of an acid mixture solution on the surface roughness, phase transformation, and biaxial flexural strength of 3Y-TZP after sintering or air abrasion. For the biaxial flexural strength measurement, 220 3Y-TZP disk-shaped specimens were prepared after as-sintering or air abrasion. The etching solution comprised a mixture of hydrofluoric acid, sulfuric acid, hydrogen peroxide, methyl alcohol, and purified water. The samples were divided into 11 subgroups according to the etching times (Control, 1, 2, 3, 5, 8, 10, 12, 15, 20, and 30 min). The results showed that acid treatment on both as-sintered and air-abraded 3Y-TZP surfaces increased the surface roughness. However, it had no significant effects on the monoclinic phase or flexural strength of as-sintered zirconia. The monoclinic phase and flexural strength of air-abraded zirconia increased sharply after air abrasion; however, they gradually decreased after acid treatment, to a similar level to the case of the untreated surface. Surface treatment with acid mixture increased the roughness, but the lack of increase of monoclinic phase is thought to be because the loose monoclinic particles remaining on the surface were removed through the etching process.

A Comparison of Accuracy of Different Dental Restorative Materials between Intraoral Scanning and Conventional Impression-Taking: An In Vitro Study

The properties of underlying substrates influence the quality of an intraoral scan, but few studies have compared the outcomes using common restorative materials. In this study, we aimed to compare the accuracy of digital and conventional impressions recorded for four different dental materials as the substrates. Experimental crowns were produced with a metallic surface (gold or cobalt-chromium alloy (Co-Cr)) or without a metallic surface (zirconia or PMMA (polymethyl methacrylate)). A conventional impression was made in the conventional group (CON group), and gypsum models were subsequently scanned with a tabletop scanner. An intraoral scanner was used to scan the crowns either after applying a powder spray to reduce the surface reflectivity (IOS-P group) or without the powder spray (IOS group). The scans were assessed in three dimensions for precision and trueness. The accuracy did not differ between the CON and IOS groups for the non-metallic crowns. However, it was statistically different for the Co-Cr metallic crown, reducing trueness observed between groups as CON > IOS > IOS-P. The study evidences the differences in outer surface accuracy observed with a change in the substrate material to be imaged using an oral scanner and with the impression method. These findings suggest that the restoration material present in the oral cavity should be considered when selecting an impression-taking method.

Effects of Groove Sealing of the Posterior Occlusal Surface and Offset of the Internal Surface on the Internal Fit and Accuracy of Implant Placements Using 3D-Printed Surgical Guides: An In Vitro Study

This study evaluated the internal fit and the accuracy of the implant placement position in order to determine how the surface shape of the tooth and the offset influence the accuracy of the surgical guide. The acquired digital data were analyzed in three dimensions using 3D inspection software. The obtained results confirmed that the internal fit was better in the groove sealing (GS) group (164.45 ± 28.34 μm) than the original shape (OS) group (204.07 ± 44.60 μm) (p < 0.001), and for an offset of 100 μm (157.50 ± 17.26 μm) than for offsets of 30 μm (206.48 ± 39.12 μm) and 60 μm (188.82 ± 48.77 μm) (p < 0.001). The accuracy of implant placement was better in the GS than OS group in terms of the entry (OS, 0.229 ± 0.092 mm; GS, 0.169 ± 0.061 mm; p < 0.001), apex (OS, 0.324 ± 0.149 mm; GS, 0.230 ± 0.124 mm; p < 0.001), and depth (OS, 0.041 ± 0.027 mm; GS, 0.025 ± 0.022 mm; p < 0.001). In addition, the entries (30 μm, 0.215 ± 0.044 mm; 60 μm, 0.172 ± 0.049 mm; 100 μm, 0.119 ± 0.050 mm; p < 0.001) were only affected by the amount of offset. These findings indicate that the accuracy of a surgical guide can be improved by directly sealing the groove of the tooth before manufacturing the surgical guide or setting the offset during the design process.

Prenylflavonoids isolated from Macaranga tanarius stimulate odontoblast differentiation of human dental pulp stem cells and tooth root formation via the mitogen-activated protein kinase and protein kinase B pathways

AIM

To identify odontogenesis-promoting compounds and examine the molecular mechanism underlying enhanced odontoblast differentiation and tooth formation.

METHODOLOGY

Five different nymphaeols, nymphaeol B (NB), isonymphaeol B (INB), nymphaeol A (NA), 3'-geranyl-naringenin (GN) and nymphaeol C (NC) were isolated from the fruit of Macaranga tanarius. The cytotoxic effect of nymphaeols on human DPSCs was observed using a 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay. The effect of nymphaeols on odontoblast differentiation was analysed with Alizarin Red S staining and odontoblast marker expression was assessed using real-time polymerase chain reaction and Western blot analysis. The molecular mechanism was investigated with Western blot analysis. In order to examine the effect of INB on dentine formation in the developing tooth germ, INB-soaked beads were placed under the tooth bud explants in the collagen gel; thereafter, the tooth bud explant-bead complexes were implanted into the sub-renal capsules for 3 weeks. Tooth root formation was analysed using micro-computed tomography and histological analysis. Data are presented as mean ± standard error (SEM) values of three independent experiments, and results are compared using a two-tailed Student's t-test. The data were considered to have statistical significance when the P-value was less than 0.05.

RESULTS

Three of the compounds, NB, INB, and GN, did not exert a cytotoxic effect on human DPSCs. However, INB was most effective in promoting the deposition of calcium minerals in vitro (P < 0.001) and induced the expression of odontogenic marker genes (P < 0.05). Moreover, this compound strongly induced the phosphorylation of mitogen-activated protein (MAP) kinases and protein kinase B (AKT) (P < 0.05). The inhibition of p38 MAP, c-Jun N-terminal kinase (JNK), and AKT substantially suppressed the INB-induced odontoblast differentiation (P < 0.001). In addition, isonymphaeol B significantly induced the formation of dentine and elongation of the tooth root in vivo (P < 0.05).

CONCLUSIONS

Prenylflavonoids, including INB, exerted stimulatory effects on odontoblast differentiation and tooth root and dentine formation via the MAP kinase and AKT signalling pathways. These results suggest that nymphaeols could stimulate the repair processes for dentine defects or injuries.

Sleeve insert scan body to predict implant placement position by using implant surgical guides: A dental technique

In studies that assessed the accuracy of implant surgical guides, evaluations were based on the placement position of the implant by using a manufactured surgical guide. However, such assessments could involve errors that may occur during implant placement. Therefore, evaluating the 3-dimensional accuracy of the fabrication of the implant surgical guide itself is not enough. In the evaluation method described in this article, location-related information is obtained by connecting a scan body to the sleeve of the surgical guide instead of directly placing the implant. This helps to evaluate the accuracy of the surgical guide without errors in the placement of an implant.

Color and Translucency Stability of Three-Dimensional Printable Dental Materials for Crown and Bridge Restorations

The purpose of this study was to examine and compare color and translucency stability of three-dimensional (3D) printable dental materials for crown and bridge restorations. Five different materials were investigated, and twelve disc-shaped specimens of two different thicknesses (1 and 2 mm) were prepared using a digital light processing 3D printer. Color measurements were made according to the CIELAB color scale (L*, a*, and b*) using a spectrophotometer 1 h, 1 day, 1 week, one month, and six months after post-curing of the materials, and the translucency parameter (TP) was calculated. The L*, a*, b*, and TP values were compared among the different materials and storage periods using repeated measures analysis of variance. Color and translucency changes of the specimens after the different storage periods were compared with 1 h measurements to determine whether they exceeded clinically perceivable thresholds. The L*, a*, b*, and TP values showed significant differences according to the storage periods, as well as among the materials. Until one month, some materials demonstrated distinct color differences, while others showed small color differences below a clinically perceivable threshold. The translucency differences were not clinically perceivable for any specimen. After six months, all specimens demonstrated large color changes, whereas the changes in translucency were relatively small. In conclusion, the color of 3D printable dental materials changed with time, and the differences varied with the materials used. On the contrary, the changes in translucency were small. Overall, the materials became darker, more yellowish, and more opaque after six months of water storage.

Evaluation of the Color Stability of 3D-Printed Crown and Bridge Materials against Various Sources of Discoloration: An In Vitro Study

Recent advances in three-dimensional (3D) printing have introduced new materials that can be utilized for dental restorations. Nonetheless, there are limited studies on the color stability of restorations using 3D-printed crowns and bridge resins. Herein, the color stability of conventional computer-aided design/computer-aided manufacturing (CAD/CAM) blocks and 3D-printing resins was evaluated and assessed for their degrees of discoloration based on material type, colorant types (grape juice, coffee, curry, and distilled water (control group)), and storage duration (2, 7, and 30 days) in the colorants. Water sorption, solubility, and scanning electron microscope (SEM) analyses were conducted. A three-way ANOVA analysis showed that all three factors significantly affected the color change of the materials. Notably, the discoloration (ΔE₀₀) was significantly higher in all 3D printing resins (4.74–22.85 over the 30 days) than in CAD/CAM blocks (0.64–4.12 over the 30 days) following immersion in all colorants. 3D-printing resins showed color differences above the clinical limit (2.25) following storage for 7 days or longer in all experimental groups. Curry was the most prominent colorant, and discoloration increased in almost all groups as the storage duration increased. This study suggests that discoloration must be considered when using 3D printing resins for restorations.

Effects of Post-Curing Time on the Mechanical and Color Properties of Three-Dimensional Printed Crown and Bridge Materials

Three-dimensional (3D) printing is increasingly being utilized in the dental field. After fabricating a prosthesis using a 3D printed resin, a post-curing process is required to improve its mechanical properties, but there has been insufficient research on the optimal post-curing conditions. We used various 3D printed crown and bridge materials in this study, and evaluated the changes in their properties according to post-curing time by evaluating the flexural strength, Weibull modulus, Vickers hardness, color change, degree of conversion, and biocompatibility. The obtained results confirmed that the strength of the 3D printed resin increased when it was post-cured for 60–90 min. The Vickers hardness, the degree of conversion, and biocompatibility of the 3D printed resins increased significantly around the beginning of the post-curing time, and then increased more gradually as the post-curing time increased further. It was observed that the color tone also changed as the post-curing time increased, with some groups showing a ΔE₀₀ value of ≥ 2.25, which can be recognized clinically. This study has confirmed that, after the printing process of a 3D printed resin was completed, a sufficient post-curing time of at least 60 min is required to improve the overall clinical performance of the produced material.

Safflower Seed Oil and Its Active Compound Acacetin Inhibit UVB-Induced Skin Photoaging

Ultraviolet (UV) is one of the major factors harmful to skin health. Irradiation with ultraviolet accelerates the decline of skin function, causing the skin to have deep wrinkles, dryness, decreased procollagen production, and degradation of collagen. Novel materials are needed to prevent the aging of the skin by blocking the effects of UV. Safflower seed oil (Charthamus tinctorius L., SSO) contains significantly high levels of unsaturated fatty acids and phytochemicals. SSO has been traditionally used in China, Japan, and Korea to improve skin and hair. Our objective in this study was to determine the effect of SSO and its active compound acacetin on UVB-induced skin photoaging in HaCaT cells and human dermal fibroblasts (HDF). SSO inhibited UVB-induced matrix metalloproteinase-1 (MMP-1) at both protein and mRNA levels in HaCaT cells and HDF. MMP-1 is known to play important roles in collagen degradation and wrinkle formation. Acacetin, a type of flavonoid, is present in SSO. Similar to SSO, acacetin also inhibited UVB-induced MMP-1 protein and mRNA levels in HaCaT cells and HDF. MMP-1 mRNA is primarily regulated by the mitogen-activated kinase (MAPK) signaling pathway. Acacetin regulated the phosphorylation of JNK1/2 and c-jun, but did not inhibit the phosphorylation of ERK1/2, p38 and AKT. Taken together, these results indicate that SSO and its active compound acacetin can prevent UVB-induced MMP-1 expression, which leads to skin photoaging, and may therefore have therapeutic potential as an anti-wrinkle agent to improve skin health.

Orobol, A Derivative of Genistein, Inhibits Heat-Killed Propionibacterium acnes-Induced Inflammation in HaCaT Keratinocytes

Acne is a chronic skin disease that typically occurs in the teens and twenties, and its symptoms vary according to age, sex, diet, and lifestyle. The condition is characterized by hyperproliferation of keratinocytes in the epidermis, sebum overproduction, excessive growth of Propionibacterium acnes, and P. acnes-induced skin inflammation. Interleukin (IL)-1α and IL-6 are predominant in the inflammatory lesions of acne vulgaris. These cytokines induce an inflammatory reaction in the skin in the presence of pathogens or stresses. Moreover, IL-1α accelerates the production of keratin 16, which is typically expressed in wounded or aberrant skin, leading to abnormalities in architecture and hyperkeratinization. Orobol (3',4',5,7-tetrahydroxyisoflavone) is a metabolite of genistein that inhibited the P. acnes-induced increases in IL-6 and IL-1α levels in human keratinocytes (HaCaTs) more effectively compared with salicylic acid. In addition, orobol decreased the IL-1α and IL-6 mRNA levels and inhibited the phosphorylation of inhibitor of kappa-B kinase, nuclear factor of kappa light polypeptide gene enhancer in B-cells inhibitor, alpha, and mitogen-activated protein kinase induced by P. acnes. Finally, the expression of Ki67 was decreased by orobol. Thus, orobol ameliorated the inflammation and hyperkeratinization induced by heat-killed P. acnes and thus has potential for use in functional foods and cosmetics.

Effect of Pressure and Particle Size During Aluminum Oxide Air Abrasion on the Flexural Strength of Disperse-Filled Composite and Polymer-Infiltrated Ceramic Network Materials

Esthetic dental computer-aided design/computer-aided manufacturing (CAD/CAM) polymers such as disperse-filled composites (DFC) and polymer-infiltrated ceramic networks (PICN) should be subjected to surface treatment before bonding. However, such treatment can lead to defect formation and a decrease in strength. Therefore, in this study, we compared the flexural strengths of DFC and PICN materials air-abraded with alumina particles of different sizes at different pressures. In addition to Weibull analysis, the samples (untreated and treated) were characterized by scanning electron microscopy and atomic force microscopy. Both DFC and PICN exhibited the lowest flexural strength at large particle sizes and high pressures. Therefore, we optimized the air abrasion parameters to maintain the flexural strength and significantly increase surface roughness. In the case of DFC, the optimal particle size and pressure conditions were 50 µm at 2 bar and 110 µm at 1 bar, while for PICN, the best performance was obtained using Al₂O₃ particles with a size of 50 µm at 1 bar. This study reveals that optimization of the surface treatment process is crucial in the fabrication of high-performance clinical materials for dental restorations.

Suspected Metallic Embolization Distal to Coiled Intracranial Aneurysms Detectable by Susceptibility-Weighted MR Imaging

BACKGROUND AND PURPOSE

After endovascular coiling of intracranial aneurysms, round dark parenchymal lesions believed to be particulate metal are sometimes encountered in MR imaging studies of the brain. We used SWI to assess the frequency of such occurrences, in addition to exploring likely causes and clinical implications.

MATERIALS AND METHODS

We reviewed 700 MR imaging studies performed between September 2018 and March 2019 at our institution as follow-up monitoring of coiled intracranial aneurysms. Any sizeable (>5 mm) rounded dark-signal lesions encountered were presumed to be metallic. The magnitudes and locations of such lesions were recorded. In patients with these lesions, pertinent procedural documentation was screened for devices used, including coils, microcatheters, microguidewires, and stents. Medical records were also examined to determine whether any related symptoms ensued.

RESULTS

Twenty patients (2.8%) exhibited a total of 25 lesions on SWI. Diameters ranged from 5 to 11 mm (median, 8 mm). All except 2 lesions were located in brain regions downstream from aneurysms, but all lesions occupied vascular territories of vessels used to place guiding catheters. Other than the Synchro 14, which was routinely deployed, no device was regularly used in patients with SWI-detectable lesions; and none of the affected patients developed focal neurologic symptoms as a consequence.

CONCLUSIONS

Although the origins remain unclear, distal embolization of particulate metal distal to coiled cerebral aneurysms is occasionally observed on follow-up MR imaging studies. Such lesions, however, seem to have no apparent clinical impact.

Mounting casts on a mechanical articulator by using digital multisource data: A dental technique

A facebow transfer is typically used for mounting a maxillary gypsum cast in an ideal location in a mechanical articulator. However, the facebow transfer procedure is difficult and may cause the patient discomfort. This proposed technique uses a patient's cone beam computed tomography (CBCT) data to reproduce the occlusal plane in relation to digital articulator scan data, align the patient's gypsum cast or intraoral scan data on the reproduced plane, and then transfer the data to a mechanical articulator.