Recent advances for dyes removal using novel adsorbents: A review

The Utilization of Chicken Egg White Waste-Modified Nanofiber Membrane for Anionic Dye Removal in Batch and Flow Systems: Comprehensive Investigations into Equilibrium, Kinetics, and Breakthrough Curve

This study investigated the use of chicken egg white (CEW) waste immobilized on weak acidic nanofiber membranes for removing the anionic acid orange 7 (AO7) dye in batch and continuous flow modes. Different experiments were conducted to evaluate the effectiveness of CEW-modified nanofiber membranes for AO7 removal, focusing on CEW immobilization conditions, adsorption kinetics, and thermodynamics. The CEW-modified nanofiber membrane (namely NM-COOH-CEW) exhibited a maximum AO7 adsorption capacity of 589.11 mg/g within approximately 30 min. The Freundlich isotherm model best represented the equilibrium adsorption data, while the adsorption kinetics followed a pseudo-second-order rate model. Breakthrough curve analysis using the Thomas model and the bed depth service time (BDST) model showed that the BDST model accurately described the curve, with an error percentage under 5%. To investigate AO7 elution efficiency, different concentrations of organic solvents or salts were tested as eluents. The NM-COOH-CEW nanofiber membrane exhibited promising performance as an effective adsorbent for removing AO7 dye from contaminated water.

Biopolymer-based beads for the adsorptive removal of organic pollutants from wastewater: Current state and future perspectives

Among biopolymer-based adsorbents, composites in the form of beads have shown promising results in terms of high adsorption capacity and ease of separation from the effluents. This review addresses the potential of biopolymer-based beads to remediate wastewaters polluted with emerging organic contaminants, for instance dyes, active pharmaceutical ingredients, pesticides, phenols, oils, polyaromatic hydrocarbons, and polychlorinated biphenyls. High adsorption capacities up to 2541.76 mg g-1 for dyes, 392 mg g-1 for pesticides and phenols, 1890.3 mg g-1 for pharmaceuticals, and 537 g g-1 for oils and organic solvents have been reported. The review also attempted to convey to its readers the significance of wastewater treatment through adsorption by providing an overview on decontamination technologies of organic water contaminants. Various preparation methods of biopolymer-based gel beads and adsorption mechanisms involved in the process of decontamination have been summarized and analyzed. Therefore, we believe there is an urge to discuss the current state of the application of biopolymer-based gel beads for the adsorption of organic pollutants from wastewater and future perspectives in this regard since it is imperative to treat wastewater before releasing into freshwater bodies.

Selective adsorption of anionic dyes by a macropore magnetic lignin-chitosan adsorbent

Dyes pollution is well known for their hazardous impacts on human health and the environment. The removal of dyes from wastewater has become an important issue. In this study, magnetic micrometer-sized particles AL-CTS@MNPs were synthesized from alkaline lignin (AL) and chitosan (CTS) by "one-pot method". The adsorbent presented higher selectivity adsorption effect on anionic dyes than amphoteric and cationic dyes, and even no adsorption effect on cationic methylene blue (MB), which showed that the anionic dyes could be better separated from the other two types of dyes. The adsorption isotherms of the dyes were highly consistent with the Langmuir model, and the maximum adsorption capacity was 329.50 mg/g for methyl orange (MO) and 20.00 mg/g for rhodamine B (RhB). AL-CTS@MNPs showed good adsorption of anionic dyes (MO) in the pH range of 3-9. Meanwhile, the adsorbent AL-CTS@MNPs were also characterized, showing rough surface with specific surface areas of 37.38 m2/g, pore diameter of 95.8 nm and porosity of 17.62 %. The particle sizes were ranged from 800 μm to 1300 μm. The electrostatic attraction and π-π* electron donor-acceptor interactions were the main forces between the adsorbent and anionic dyes. While the electrostatic repulsive force between the adsorbent and the cationic dyes resulted in the non-absorption of MB by AL-CTS@MNPs. Subsequently, the adsorbent maintained a removal rate of >95 % after five adsorption-desorption cycles, demonstrating its excellent stability and recoverability. Ultimately, the prepared AL-CTS@MNPs illuminated good prospect on complex components dyes wastewater treatment.

Novel granular bentonite-carbon sorbents: textural characterization, adsorption-desorption isotherm, kinetics, and cost estimation

This research focuses on the synthesis of novel low-cost granular sorbents based on bentonite clay of the Navbahor deposit, dust fraction of Angren brown coal, and agricultural wastes such as straw and sawdust to meet the internal needs of the Republic of Uzbekistan. The impact of the initial mixture ingredients on the structural and textural properties of bentonite-coal sorbents (BCSs) has been studied using X-ray diffraction, Raman spectroscopy, Fourier-transform infrared spectroscopy, optical microscopy, and nitrogen adsorption-desorption analysis. For determining the sorption capacity of BCSs, a standard model substance methylene blue (MB), was applied. It was revealed that the maximum adsorption amount of MB was 5.3 mg∙g-1 during 2 h of contact. Prolonging the contact time to 24 h allowed for more extensive diffusion of dye molecules into the sorbent's pores, increasing the adsorption capacity to 13 mg∙g-1. It was demonstrated that BCSs could be regenerated by strong oxidizing agents such as sulfuric acid and hydrogen peroxide, with sulfuric acid proving more effective. Regeneration fully restores sorption properties, particularly at low dye concentrations (up to 0.2 mg∙ml-1). Despite slight reductions in adsorption capacity over multiple regeneration cycles, the sorbents maintain their structural integrity and durability. It is shown that compared to imported expensive activated carbon, the gross profitability of the in-house production of such granular BCSs within the territory of Uzbekistan increases from 48 to 78%, while the net income increases almost three times.

Structure Characterization and Dye Adsorption Properties of Modified Fiber from Wheat Bran

The fibers from four wheat varieties (FT, XW 26, XW 45, and KW 1701) were selected and chemically modified with NaOH, epichlorohydrin, and dimethylamine to improve the adsorption capacity for anionic dye. The structure of the fibers with or without modification was characterized by scanning electron microscope (SEM), X-ray diffraction (XRD), and Fourier-transform infrared (FTIR) spectrometry. The modified products were studied from the aspects of adsorption capacities, adsorption kinetics, and thermodynamics to provide a reference for the utilization of wheat bran. By SEM, more porous and irregular structures were found on the modified fibers. The XRD results showed that the crystals from the original fibers were destroyed in the modification process. The changes in fibers' infrared spectra before and after modification suggested that quaternary ammonium salts were probably formed in the modification process. The maximum adsorption capacity of wheat bran fibers for Congo red within 120 min was 20 mg/g for the unmodified fiber (XW 26) and 93.46 mg/g for the modified one (XW 45). The adsorption kinetics of Congo red by modified wheat bran fiber was in accord with the pseudo-second-order kinetic model at 40 °C, 50 °C, and 60 °C, indicating that the adsorption process might be mainly dominated by chemisorption. The adsorption was more consistent with the Langmuir isothermal adsorption model, implying that this process was monolayer adsorption. The thermodynamic parameters suggested that the adsorption occurred spontaneously, and the temperature increase was favorable to the adsorption. As mentioned above, this study proved that the wheat bran fiber could possess good adsorption capacities for anion dye after chemical modification.

Recovery of Ag(I) from Wastewater by Adsorption: Status and Challenges

Untreated or inadequately treated silver-containing wastewater may pose adverse effects on hu-man health and the ecological environment. Currently, significant progress has been made in the treatment of Ag(I) in wastewater using adsorption methods, with adsorbents playing a pivotal role in this process. This paper provides a systematic review of various adsorbents for the recovery and treatment of Ag(I) in wastewater, including MOFs, COFs, transition metal sulfides, metal oxides, biomass materials, and other polymeric materials. The adsorption mechanisms of these materials for Ag(I) are elaborated upon, along with the challenges currently faced. Furthermore, insights into optimizing adsorbents and developing novel adsorbents are proposed in this study.

Study on Preparation of Calcium-Based Modified Coal Gangue and Its Adsorption Dye Characteristics

Efficient and thorough treatment of dye wastewater is essential to achieve ecological harmony. In this study, a new type of calcium-based modified coal gangue (Ca-CG) was prepared by using solid waste coal gangue as raw material and a CaCl2 modifier, which was used for the removal of malachite green, methylene blue, crystal violet, methyl violet and other dyes in water. When the dosage of Ca-CG was 1-5 g/L, the dosage of Ca-CG was the main factor affecting the dye adsorption effect. The adsorption effects of Ca-CG on four dyes were as follows: malachite green > crystal violet > methylene blue > methyl violet. Kinetics, isotherms and thermodynamic analysis showed that the adsorption of malachite green, methyl blue, crystal violet and methyl violet by Ca-CG fitted the second-order kinetic model, and adsorption with chemical reaction is the main process. The adsorption of four dyes by Ca-CG conformed to the Freundlich model, which is dominated by multi-molecular layer adsorption, and the adsorption was easy to carry out. The adsorption process of Ca-CG on the four dyes was spontaneous. The results of FTIR, XRD and SEM showed that the calcium-based materials such as lipscombite and dolomite were the key to the adsorption of malachite green by Ca-CG, and the main mechanisms for the adsorption of malachite green by Ca-CG are surface precipitation, electrostatic action, and chelation reaction. Ca-CG adsorption has great potential for the removal of dye wastewater.

Reuse of iron ore tailings as an efficient adsorbent to remove dyes from aqueous solution

In this work, an iron ore tailings sample (IOT), collected from a tailings dam in Minas Gerais, Brazil, was characterized. The IOT presented point of zero charge of ∼ 6, specific surface area of 4 m2 g-1, and was mainly composed of hematite and quartz. Subsequently, experiments were performed to evaluate the adsorption of an anionic dye, Direct Red 80 (DR80), and a cationic dye, Methylene Blue (MB), by the IOT, studying the effects of its dose (doseIOT) and the solution initial pH (pH0). The DR80 removal increased with the decrease of the pH0 while the opposite effect occurred in the experiments with the MB, suggesting the process is governed by the adsorption resulting from electrostatic forces. The increase in the doseIOT increased the DR80 and MB removal, which can be attributed to the greater availability of adsorption sites. Pseudo-second order kinetic (R2 > 0.9994) and the Langmuir equilibrium isotherm (R2 > 0.9842) models described well the DR80 adsorption by the IOT, being the reaction rate and maximum adsorption capacity higher at lower pH0. In a regeneration experiment, it was possible to desorb almost entirely the DR80 using a NaOH solution. Additionally, the regenerated IOT was able to adsorb the DR80, demonstrating its reusability. In a preliminary assay, the IOT decreased the colour of the textile wastewater sample at pH0 3. Therefore, the results indicate the potential use of IOT for removing electric-charged pollutants by adsorption, especially anionic ones under acidic conditions.

A critical review and bibliometric analysis of methylene blue adsorption using leaves

The rapid development of the industrial world causes wastewater containing dyes to continue to increase. Even in recent years, the food, textile, cosmetic, plastic, and printing industries have developed the use of dyes. Methylene blue (MB) is one of the cationic dyes widely used in dyeing silk, wood, and cotton because of its absorbency and good fastness to materials. The adsorption process is the best technique and preferred in removing dyes from wastewater due to excellent selectivity, high efficiency from high-quality treated effluent, flexibility in design, and simplicity. Therefore, there is a growing interest to identify low-cost alternative adsorbents that have reasonable adsorption efficiency, especially natural materials such as leaves. In this study, research on MB adsorption using leaves was analyzed using bibliometric analysis. Information of bibliometric is extracted from the Scopus database with the keyword "Methylene Blue", "Adsorption or Desorption", and "Leaves or leaf". The results showed that India, Desalination and Water Treatment, and SASTRA Deemed University were the country, journal, and institution that contributed the most publications on this topic. Therefore, it is expected that with the use of bibliometrics, the use of leaf-based MB adsorption processes in their potential for MB dye removal can be investigated especially for large-scale development.

Advancements in application of modified biochar as a green and low-cost adsorbent for wastewater remediation from organic dyes

Synthetic organic dyes, which are resistant to biodegradation, pose a notable health risk, potentially leading to cancer and respiratory infections. Researchers have addressed this concern by exploring physicochemical methods to remove organic dyes from wastewater. A particularly promising solution involves modified biochar adsorbents, which demonstrate high efficiency in organic dye removal. Biochar, a charcoal-like material derived from biomass pyrolysis, offers advantages such as low cost, eco-friendliness, high efficiency and reusability. Beyond its role in sustainable soil remediation, biochar proves effective in removing organic dyes from wastewater after undergoing physical or chemical modification. Acid-base activation or metal-heteroatom impregnation enhances biochar's adsorption capacity. This comprehensive review examines the attributes of biochar, common methods for production and modification, and the impacts of raw materials, pyrolysis temperature, heating rate and residence time. It further elucidates the biochar adsorption mechanism in the removal of organic dyes, assessing factors influencing efficiency, including biochar feedstock, solution pH, adsorption temperature, particle size, initial dye concentration, biochar dosage and reaction time. It explores challenges, opportunities, reusability and regeneration methods of biochar in treating organic dye wastewater. It also discusses recent advances in organic dye removal using adsorption-based biochar. The review ultimately advocates for enhancing biochar's adsorption performance through post-modification.

Synthesis of Composite Sorbents with Chitosan and Varied Silica Phases for the Adsorption of Anionic Dyes

In this work, various types of silica materials were used for the synthesis of chitosan-silica composites. The composites were obtained using the chitosan (Ch) immobilization process from an aqueous solution on various silica phases, i.e., amorphous diatomite (ChAD), crystalline diatomite (ChCD), mesoporous silica MCM-41 (ChMCM), and mesoporous silica SBA-15 (ChSBA). Textural, structural, morphological, and surface properties of the materials were determined by using various measurement techniques, i.e., low-temperature adsorption/desorption isotherms of nitrogen, X-ray diffraction (XRD), small-angle X-ray scattering (SAXS), potentiometric titration, high-resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The adsorption properties towards various anionic dyes, i.e., acid red 88 (AR88), acid orange 8 (AO8), and orange G (OG), were evaluated based on kinetic and equilibrium measurements. The ChSBA, ChAD, and ChMCM composites were characterized by relatively high adsorption capacities (am) for AR88, with values equal to 0.78, 0.71, and 0.69 mmol/g, respectively. These composites were also distinguished by the rapid AR88 adsorption rate, with the values of half-time parameter t0.5 equal to 0.35, 2.84, and 1.53 min, respectively. The adsorption equilibrium and kinetic data were analyzed by applying the generalized Langmuir isotherm and the multi-exponential equation (m-exp), respectively. An interaction mechanism between the dyes and the obtained materials was proposed.

Removal of dyes from wastewater using Eucalyptus wood fiber loaded nanoscale zero-valent iron: Characterization and removal mechanism

Wood fiber as a natural and renewable material has low cost and plenty of functional groups, which owns the ability to adsorb dyes. In order to improve the application performance of wood fiber in dye-pollution wastewater, Eucalyptus wood fiber loaded nanoscale zero-valent iron (EWF-nZVI) was developed to give EWF magnetism and the ability to degrade dyes. EWF-nZVI was characterized via FTIR, XRD, zeta potential, VSM, SEM-EDS and XPS. Results showed that EWF-nZVI owned a strong magnetism of 96.51 emu/g. The dye removal process of EWF-nZVI was more in line with the pseudo-second-order kinetics model. In addition, the Langmuir isotherm model fitting results showed that the maximum removal capacities of Congo red and Rhodamine B by EWF-nZVI were 714.29 mg/g and 68.49 mg/g at 328 K, respectively. After five adsorption-desorption cycles, the regeneration efficiencies of Congo red and Rhodamine B were 74 % and 42 % in turn. The dye removal mechanisms of EWF-nZVI included redox degradation (Congo red and Rhodamine B) and electrostatic adsorption (Congo red). In summary, EWF-nZVI is a promising biomass-based material with high dye removal capacities. This work is beneficial to promote the large-scale application of wood fiber in water treatment.

Removal of Azo Dyes from Water Using Natural Luffa cylindrica as a Non-Conventional Adsorbent

Reducing high concentrations of pollutants such as heavy metals, pesticides, drugs, and dyes from water is an emerging necessity. We evaluated the use of Luffa cylindrica (Lc) as a natural non-conventional adsorbent to remove azo dye mixture (ADM) from water. The capacity of Lc at three different doses (2.5, 5.0, and 10.0 g/L) was evaluated using three concentrations of azo dyes (0.125, 0.250, and 0.500 g/L). The removal percent (R%), maximum adsorption capacity (Qm), isotherm and kinetics adsorption models, and pH influence were evaluated, and Fourier-transform infrared spectroscopy and scanning electron microscopy were performed. The maximum R% was 70.8% for 10.0 g L-1Lc and 0.125 g L-1 ADM. The Qm of Lc was 161.29 mg g-1. Adsorption by Lc obeys a Langmuir isotherm and occurs through the pseudo-second-order kinetic model. Statistical analysis showed that the adsorbent dose, the azo dye concentration, and contact time significantly influenced R% and the adsorption capacity. These findings indicate that Lc could be used as a natural non-conventional adsorbent to reduce ADM in water, and it has a potential application in the pretreatment of wastewaters.

One-Step Synthesis of Polyethyleneimine-Grafted Styrene-Maleic Anhydride Copolymer Adsorbents for Effective Adsorption of Anionic Dyes

Wastewater containing organic dyes has become one of the important challenges in water treatment due to its high salt content and resistance to natural degradation. In this work, a novelty adsorbent, PEI-SMA, was prepared by grafting polyethyleneimine (PEI) onto styrene-maleic anhydride copolymer (SMA) through an amidation reaction. The various factors, such as pH, adsorbent dosage, contact time, dye concentration, and temperature, which may affect the adsorption of PEI-SMA for Reactive Black 5 (RB5), were systematically investigated by static adsorption experiments. The adsorption process of PEI-SMA for RB5 was more consistent with the Langmuir isotherm model and the pseudo-second-order model, suggesting a single-layer chemisorption. PEI-SMA exhibits excellent adsorption performance for RB5 dye, with a maximum adsorption capacity of 1749.19 mg g-1 at pH = 2. Additionally, PEI-SMA exhibited highly efficient RB5 competitive adsorption against coexisting Cl- and SO42- ions and cationic dyes. The adsorption mechanism was explored, and it can be explained as the synergistic effect of electrostatic interaction, hydrogen bonding and π-π interaction. This study demonstrates that PEI-SMA could act as a high performance and promising candidate for the effective adsorption of anionic dyes from aqueous solutions.

Novel Chitosan-ZnO nanocomposites derived from Nymphaeaceae fronds for highly efficient removal of Reactive Blue 19, Reactive Orange 16, and Congo Red dyes

The primary aim of this investigation was to synthesise novel adsorbent by incorporating greenly synthesized zinc oxide nanoparticles into chitosan matrix (G-ZnO-Cs). The production of ZnO Nanoparticles via a green approach involved the utilization of extracts derived from Nymphaeaceae fronds. This assertion was substantiated by the application of Field Emission Scanning Electron Microscopy (FESEM) and X-ray Diffraction (XRD) analytical techniques. Several Analytical methods such as Fourier Transform Infrared spectroscopy (FT-IR), Energy Dispersive X-ray Analysis (EDAX), FESEM, Thermogravimetric Analysis (TGA), XRD, Brunauer-Emmett-Teller (BET) analysis, and point-of-zero charge determination were used to characterize G-ZnO-Cs. Further study investigates the impact of five key processing parameters, namely pH, interaction duration, G-ZnO-Cs dosage, temperature, and initial concentration of dyes, on the removal of three organic dyes Reactive Blue 19 (RB 19), Reactive Orange 16 (RO 16), and Congo Red (CR) The adsorption process of Reactive Blue 19 (RB 19), Reactive Orange 16 (RO 16), and Congo Red (CR) dyes on G-ZnO-Cs were determined to comply to the pseudo-second-order (PSO) and Langmuir models, as determined through equilibrium and kinetic experiments. The highest adsorption capabilities for RB 19, RO 16 and CR dye were revealed to be 219.6 mg/g, 129.6 mg/g, and 118.8 mg/g, respectively. The elimination success rate of the fixed-bed column approach for treating huge volumes was highlighted in the conducted research. Moreover, the G-ZnO-Cs composite exhibited significant reusability due to its ability to undergo elution and simultaneous regeneration processes.

Natural Polysaccharide-Based Hydrogels Used for Dye Removal

Removal of contaminants from discharge water is vital and demands urgent assistance with the goal to keep clean water. Adsorption is one of the most common, efficient, and low-priced methods used in water treatment. Various polysaccharide-based gels have been used as efficient dye adsorbents from wastewater. This review summarizes cutting-edge research of the last decade of different hydrogels based on natural polysaccharides (chitin, chitosan, cellulose, starch, pullulan, and dextran) concerning their dye adsorption efficiency. Beyond their natural abundance, attributes of polysaccharides such as biocompatibility, biodegradability, and low cost make them not only efficient, but also environmentally sustainable candidates for water purification. The synthesis and dye removal performance together with the effect of diverse factors on gels retaining ability, kinetic, and isotherm models encountered in adsorption studies, are introduced. Thermodynamic parameters, sorbent recycling capacity along with conclusions and future prospects are also presented.

Synthesis and characterization of citric acid-modified chitosan Schiff base with enhanced antibacterial properties for the elimination of Bismarck Brown R and Rhodamine B dyes from wastewater

In this study, a new chitosan Schiff base with surface modification using citric acid was synthesized for efficient removal of pernicious dyes, namely Bismarck Brown R (BBR) and Rhodamine B (RhB), from wastewater. The physicochemical properties of the modified chitosan Schiff base were comprehensively investigated. Adsorption studies demonstrated that BBR adsorption occurred through monolayer formation, while RhB adsorption proceeded via multilayer formation on the heterogeneous surface. The synthesized adsorbent exhibited exceptional dye removal efficiency, with a Langmuir saturation capacity of 348 ± 11.0 mg.g-1 for BBR and 145 ± 18.44 mg.g-1 for RhB. Isotherm data fitting revealed consistency with the Langmuir isotherm model for BBR and the Freundlich isotherm model for RhB. Notably, the modified chitosan Schiff base showcased enhanced antibacterial properties, effectively inhibiting both gram-positive and gram-negative bacteria. The study's findings underscore the potential of this novel chitosan-based Schiff base as an efficient adsorbent for the removal of various dyes from wastewater, emphasizing its versatility and practical applicability in water treatment processes.

Surface modification of toner-based recyclable iron oxide self-doped graphite nanocomposite to enhance methylene blue and tetracycline adsorption

An innovative task was undertaken to convert ubiquitous and toxic electronic waste, waste toner powder (WTP), into novel adsorbents. Alkaline modification with KOH, NaOH, and NH4OH was employed for the first time to synthesize a series of surface-modified WTP with enhanced dispersibility and adsorption capacity. XRD, XRF, FTIR, and BET analyses confirmed that the prepared KOH-WTP, NaOH-WTP, and NH4OH-WTP were oxygen-functionalized self-doped iron oxide-graphite nanocomposites. The prepared adsorbents were used to remove methylene blue and tetracycline from aqueous solutions. KOH-WTP (0.1 g/100 mL) adsorbed 80% of 10 mg/L methylene blue within 1 h, while 0.1 g/100 mL NH4OH-WTP removed 72% of 10 mg/L tetracycline in 3 h. Exploring surface chemistry by altering solution pH and temperature suggested that hydrogen bonding, electrostatic interactions, π-π electron stacking, and pore filling were plausible adsorption mechanisms. Scanning electron microscopy revealed a diminishing adsorbents porosity after adsorption proving the filling of pores by the adsorbates. KOH-WTP and NH4OH-WTP removed 77% and 61% of methylene blue and tetracycline respectively in the fourth reuse. The adsorption data of methylene blue and tetracycline fitted the Freundlich isotherm model. The maximum adsorption capacities of KOH-WTP and NH4OH-WTP for methylene blue and tetracycline were 59 mg/g and 43 mg/g respectively. The prepared adsorbents were also compared with other adsorbents to assess their performance. The transformation of waste toner powder into magnetically separable oxygen-functionalized WTP with outstanding recyclability and adsorption capacity showcases a significant advancement in sustainable wastewater treatment. This further aligns with the principles of the circular economy through the utilization of toxic e-waste in value-added applications. Additionally, magnetic separation of surface-modified WTP post-treatment can curtail filtration and centrifugation expenses and adsorbent loss during wastewater treatment.

A review of pre- and post-surface-modified neem (Azadirachta indica) biomass adsorbent: Surface functionalization mechanism and application

In contemporary wastewater treatment industry, advanced oxidation techniques, membrane filtration, ion exchange, and reverse osmosis are used to treat chemically loaded wastewater. All these methods required highly toxic oxidizing chemicals, high capital investment in membrane/filter materials, and the installation of sophisticated equipment. Wastewater treatment through an adsorption process using biomass-based adsorbent is economical, user-friendly, and sustainable. Neem tree waste has been explored as an adsorbent for wastewater treatment. The chemical components in the neem biomass include carbohydrates, fat, fiber, cellulose, hemicellulose, and lignin, which support the functionalization of neem biomass. Moreover, adsorbent preparation from renewable resources is not only cost-effective and environmentally friendly but also helps in waste management for sustainable growth. Contemporary researchers explored the pre- and post-surface-modified neem biomass adsorbents in scavenging the pollutants from contaminated water. This review extensively explores the activation process of neem biomass, physical and chemical methods of surface modification mechanism, and the factors affecting surface modification. The pollutant removal through pre and post-surface-modified neem biomass adsorbents was also summarized. Furthermore, it also provides a comprehensive summary of the factors that affect the adsorption performance of the neem biomass-derived adsorbents against dyes, metal ions, and other emerging pollutants. Understanding the surface-modification mechanisms and the adsorption efficiency factor of adsorbents will help in harnessing their potential for more efficiently combatting environmental pollution and making strides toward a greener and more sustainable future.

Gardenia yellow pigment: Extraction methods, biological activities, current trends, and future prospects

Food coloring plays a vital role in influencing consumers' food choices, imparting vibrant and appealing colors to various food and beverage products. Synthetic food colorants have been the most commonly used coloring agents in the food industry. However, concerns about potential health issues related to synthetic colorants, coupled with increasing consumer demands for food safety and health, have led food manufacturers to explore natural alternatives. Natural pigments not only offer a wide range of colors to food products but also exhibit beneficial bioactive properties. Gardenia yellow pigment is a water-soluble natural pigment with various biological activities, widely present in gardenia fruits. Therefore, this paper aims to delve into Gardenia Yellow Pigment, highlighting its significance as a food colorant. Firstly, a thorough understanding and exploration of various methods for obtaining gardenia yellow pigment. Subsequently, the potential functionality of gardenia yellow pigment was elaborated, especially its excellent antioxidant and neuroprotective properties. Finally, the widespread application trend of gardenia yellow pigment in the food industry was explored, as well as the challenges faced by the future development of gardenia yellow pigment in the field of food and health. Some feasible solutions were proposed, providing valuable references and insights for researchers, food industry professionals, and policy makers.

Expermental investigation on adsorption of methylene blue dye from waste water using corncob cellulose-based hydrogel

Hydrogel from corncob cellulose was synthesized in this investigation. The synthesized Hydrogel was characterized by SEM, XRD, and FTIR instruments. As the results indicate the synthesized hydrogel has required and important features, these suggest the suitability of hydrogel for the adsorption of methylene blue dye (MBD). Three important process variables (dosage, contact time, and initial concentration) with three levels were studied during the adsorption process at 30 °C and neutral pH. The efficiency of hydrogel for adsorption of MBD was determined in each experiment. The experimental results were statistically analyzed and interpreted. The maximum removal efficiency was achieved at 2.22 g/L of dosage, 80.36 min of contact time, and 74.54 mg/L of initial concentration. At this condition, 98.25% of MBD was achieved through experimental tests. Kinetics, isotherm, and thermodynamics studies were performed. Langmuir isotherm is more suitable to describe the adsorption process and the Pseudo second-order kinetic model fits this process. From the thermodynamics studies, all negative values of change in Gibbs free energy (ΔG°), and positive value of change in enthalpy (ΔH°), and change in entropy (ΔS°) indicate that the carried out experimental process is a spontaneous and endothermic. Moreover, the regeneration experiment for adsorbent was performed. The treatment of real textile industry waste water was conducted and the removal efficiency of hydrogel was 64.76%. This removal percentage reduction from sythetic aqueous solution is due to involvement of other pollutants in the real waste water. The synthesized hydrogel adsorbent is suitable up to the third cycle without significant loss in removal efficiency.

Preparation of a Novel Lignocellulose-Based Aerogel by Partially Dissolving Medulla Tetrapanacis via Ionic Liquid

A novel lignocellulosic aerogel, MT-LCA, was successfully prepared from MT by undergoing partial dissolution in an ionic liquid, coagulation in water, freezing in liquid nitrogen, and subsequent freeze-drying. The MT-LCA preserves its original honeycomb-like porous structure, and the newly formed micropores contribute to increased porosity and specific surface area. FT-IR analysis reveals that MT, after dissolution and coagulation, experiences no chemical reactions. However, a change in the crystalline structure of cellulose is observed, transitioning from cellulose I to cellulose II. Both MT and MT-LCA demonstrate a quasi-second-order kinetic process during methylene blue adsorption, indicative of chemical adsorption. The Langmuir model proves to be more appropriate for characterizing the methylene blue adsorption process. Both adsorbents exhibit monolayer adsorption, and their effective adsorption sites are uniformly distributed. The higher porosity, nanoscale micropores, and larger pore size in MT-LCA enhance its capillary force, providing efficient directional transport performance. Consequently, the prepared MT-LCA displays exceptional compressive performance and efficient directional transport capabilities, making it well-suited for applications requiring high compressive performance and selective directional transport.

Recent advances in visible light-activated photocatalysts for degradation of dyes: A comprehensive review

The rapid development in industrialization and urbanization coupled with an ever-increasing world population has caused a tremendous increase in contamination of water resources globally. Synthetic dyes have emerged as a major contributor to environmental pollution due to their release in large quantities into the environment, especially owing to their high demand in textile, cosmetics, clothing, food, paper, rubber, printing, and plastic industries. Photocatalytic treatment technology has gained immense research attention for dye contaminated wastewater treatment due to its environment-friendliness, ability to completely degrade dye molecules using light irradiation, high efficiency, and no generation of secondary waste. Photocatalytic technology is evolving rapidly, and the foremost goal is to synthesize highly efficient photocatalysts with solar energy harvesting abilities. The current review provides a comprehensive overview of the most recent advances in highly efficient visible light-activated photocatalysts for dye degradation, including methods of synthesis, strategies for improving photocatalytic activity, regeneration and their performance in real industrial effluent. The influence of various operational parameters on photocatalytic activity are critically evaluated in this article. Finally, this review briefly discusses the current challenges and prospects of visible-light driven photocatalysts. This review serves as a convenient and comprehensive resource for comparing and studying the fundamentals and recent advancements in visible light photocatalysts and will facilitate further research in this direction.

Biochar obtained from alkaline earth metal-treated mushroom residue: Thermal behavior and methyl orange adsorption capability

To achieve the resource utilization of edible fungi residue and obtain efficient adsorbents for treating dyeing wastewater, biochars were prepared from mushroom residue (MR) with the introduction of alkaline-earth metals (AEMs) and used for methyl orange (MO) wastewater treatment. The thermal behavior of the AEM-treated MR was analyzed using thermogravimetric analysis. The physicochemical properties of the biochars obtained from AEM-treated MR (MRCs) were characterized using Fourier transform infrared spectroscopy, laser particle size analyzer, N2 adsorption/desorption, and scanning electron microscopy. The adsorption performance of MRCs on MO was also investigated. The involvement of AEMs was found to obviously move the main pyrolysis zone of MR to a low temperature region and reduce the temperature corresponding to the maximum weight loss rate and activation energy, which is highly dependent on the concentration of AEMs, the anion and cationic species of the AEMs. Moreover, the addition of AEMs resulted in a decrease in oxygen-containing functional groups (-OH, CO, or C-O), a weakening of surface negative charges, an enhancement in aromatic functional groups, and an increase in specific surface area of the MRCs. The adsorption performance of MO on MRCs was significantly improved with the introduction of AEMs as well. Among them, MR pre-treated with 5 mmol/g MgCl2 (MR-MgCl2-5) shows the lowest temperature corresponding to the maximum weight loss rate and the lowest activation energy of 278.52 °C and 4.28 kJ/mol, respectively. The biochar prepared from MR-MgCl2-5 under 400 °C (MR-MgCl2-5-400C) has the weakest surface negative charge and the highest adsorption capacity for MO. The adsorption isotherms, adsorption kinetics, and thermodynamic analysis results showed that the adsorption of MO on MR-MgCl2-5-400C was a spontaneous, chemically dominant monolayer adsorption, with a theoretical maximum adsorption capacity of 81.30 mg/g. This study suggests that AEMs treatment, especially with 5 mmol/g MgCl2, can readily transform edible fungi residue into a low-cost, high-efficient dyeing wastewater adsorbent.

AI-enhanced adsorption modeling: Challenges, applications, and bibliographic analysis

Inorganic and organic contaminants, such as fertilisers, heavy metals, and dyes, are the primary causes of water pollution. The field of artificial intelligence (AI) has received significant interest due to its capacity to address challenges across various fields. The use of AI techniques in water treatment and desalination has recently shown useful for optimising processes and dealing with the challenges of water pollution and scarcity. The utilization of AI in the water treatment industry is anticipated to result in a reduction in operational expenditures through the lowering of procedure costs and the optimisation of chemical utilization. The predictive capabilities of artificial intelligence models have accurately assessed the efficacy of different adsorbents in removing contaminants from wastewater. This article provides an overview of the various AI techniques and how they can be used in the adsorption of contaminants during the water treatment process. The reviewed publications were analysed for their diversity in journal type, publication year, research methodology, and initial study context. Citation network analysis, an objective method, and tools like VOSviewer are used to find these groups. The primary issues that need to be addressed include the availability and selection of data, low reproducibility, and little proof of uses in real water treatment. The provision of challenges is essential to ensure the prospective success of AI associated with technologies. The brief overview holds importance to everyone involved in the field of water, encompassing scientists, engineers, students, and stakeholders.

Design of chitosan/boehmite biocomposite for the removal of anionic and nonionic dyes from aqueous solutions: Adsorption isotherms, kinetics, and thermodynamics studies

This study introduces a chitosan/boehmite biocomposite as an efficient adsorbent for removing anionic Congo Red (CR) and non-ionic Bromothymol Blue (BTB) from water. Boehmite nanoparticles were synthesized using the Sol-gel method and then attached to chitosan particles using sodium tripolyphosphate through co-precipitation method. Characterized through FTIR, FE-SEM, BET, and XRD, the biosorbent displayed structural integrity with optimized pH conditions of 3 for CR and 4 for BTB, achieving over 90 % adsorption within 30 min. Pseudo second order kinetics model and Langmuir isotherm revealed monolayer sorption with capacities of 64.93 mg/g for CR and 90.90 mg/g for BTB. Thermodynamics indicated a spontaneous and exothermic process, with physisorption as the primary mechanism. The biosorbent demonstrated excellent performance and recyclability over five cycles, highlighting its potential for eco-friendly dye removal in contaminated waters.

Selective extraction of anionic and cationic dyes using tailored hydrophobic deep eutectic solvents

In this work, eight kinds of hydrophobic deep eutectic solvents (DESs), including four types of ionic and four types of non-ionic DESs, were prepared and applied in vortex-assisted liquid-liquid microextraction (LLME) technology. To explore the extraction ability of the hydrophobic DESs-based vortex-assisted LLME, four types of dyes were selected as analytes, involving anionic tartrazine (TA), amaranth (AM) and cationic phenosafranine (PF), methylene blue (MB). It turned out that the ionic and non-ionic hydrophobic DESs showed selective extraction on anionic and cationic dyes, respectively. In particular, the extraction efficiency of TA could reach 99.3 % when trioctylmethylammonium chloride-thymol ([TMAC][Thy]) was utilized as extraction agent. The partitioning efficiency of PF was up to 99.9 % by using decanoic acid-thymol ([DecA][Thy]) as extraction agent. The limits of detection (LODs) of TA and PF were 0.06 and 0.14 μg mL-1, respectively. The limits of quantification (LOQs) obtained for TA and PF were 0.20 and 0.47 μg mL-1, respectively. Besides, FT-IR and 1H NMR were utilized to investigate the extraction mechanism. The results demonstrated that the hydrogen bonding and electrostatic force were the main driving forces in the extraction process. Furthermore, through separating various anionic and cationic dyes, the selective extraction ability of [TMAC][Thy] and [DecA][Thy] were successfully verified. Hence, the feasible operation, high extraction efficiency and excellent selectivity make the developed hydrophobic DESs-based vortex-assisted LLME attractive in dyes separation.

Heterogeneous MIL-88A on MIL-88B hybrid: A promising eco-friendly hybrid from green synthesis to dual application (Adsorption and photocatalysis) in tetracycline and dyes removal

Herein, the green synthesis of heterogeneous dual functional MIL88A-on-MIL88B hybrids (MIL: Materials InstituteLavoisier) with different amounts of MIL88B compared to MIL88A, including 1:2, 1:1, and 2:1, has been carried out. The photocatalytic degradation of tetracycline and adsorption of tetracycline and dyes (Direct Red 80, Direct Red 23, Acid Blue 92, and Reactive Orange 14) were investigated. Although the ratio of MIL88A-on-MIL88B (1:1) hybrid displayed the best activity, there is a slight difference in the photocatalytic performance of the other mass ratios studied. The result revealed that after 70 min of forming MIL88A on MIL88B, the best pollutant removal performance is obtained. During the limited synthesis time, the lopsided growth of MIL88A on the MIL88B surface limits the formation of sufficient functional groups and new pores between MIL88B as the substrate and MIL88A, which are effective and decisive in the performance. In the photocatalytic studies, the synthesized composite had good compatibility with the zero-order kinetics, and hydroxyl radicals were recognized as the most active species in the photocatalytic reaction. In the adsorption process, the MIL88A-on-MIL88A composite followed pseudo-second-order kinetics and the Langmuir isotherm. Besides, mechanisms such as π-π interaction/stacking, hydrogen bonding, and π-metal interaction were proposed for the pollutant adsorption process.

Upgraded β-cyclodextrin-based broad-spectrum adsorbents with enhanced antibacterial property for high-efficient dyeing wastewater remediation

The dyeing wastewater contains amounts of refractory organic compounds, and severely endangers the ecosystem and human health. To alleviate this problem, in this study, the low-cost broad-spectrum nano-adsorbent (denoted as CD/CA-g-CS) with strong antibacterial activity has been synthesized by chemical binding of β-cyclodextrin (β-CD) with chitosan (CS) and citric acid (CA) for high-efficient dyes scavenger. Taking advantage of the extraordinary water insolubility, porous nature and abundant surface groups, the synthesized CD/CA-g-CS outperforms the previously reported adsorbents in terms of adsorption performance. The CD/CA-g-CS exhibits ultrahigh adsorption capacities of 801.66, 770.50 and 946.66 mg/g, respectively mg/g for the cationic dyes of malachite green (MG), basic red (BR) and methylene blue (MB), respectively, while 389.64, 619.60 and 429.22 mg/g for the anionic dyes of acid blue (AB), acid red (AR) and acid yellow (AY), respectively. The chemical monolayer absorption is further demonstrated by the analysis based on the pseudo-second-order adsorption kinetics and Langmuir isotherm models. The regenerable CD/CA-g-CS not only performs well in one-step removal of the mixed dyes in the simulated sewage, but also exhibits superior performance in purifying real industrial wastewater. Moreover, CD/CA-g-CS endowed with antibacterial activity leads to an inhibition rate of over 99.99 % for E. coli. The newly developed CD/CA-g-CS adsorbents are highly promising for high-efficient dyeing wastewater remediation.

Synthesis and characterization of Alg/Gel/n-HAP/MNPs porous nanocomposite adsorbent for efficient water conservancy and removal of methylene blue in aqueous environments: Kinetic modeling and artificial neural network predictions

In this study, a new porous nanocomposite adsorbent for water conservancy was synthesized using the freeze-drying technique to adsorb a cationic dye (Methylene Blue) in an aqueous environment. The nanocomposite adsorbent was synthesized using natural polymers, gelatin, and sodium alginate, and hydroxyapatite and magnetic iron oxide nanoparticles was incorporated into the polymer network to improve mechanical properties and increase the surface-to-volume ratio. To confirm the structure and morphology of the sample, Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron microscope (SEM) techniques were employed. In addition, the magnetic properties of the synthesis of MNPs and porous nanocomposite were determined using value stream mapping (VSM) and dynamic light scattering (DLS). The adsorption of Methylene Blue (MB) was studied as a function of effective physical and variable parameters, such as time, temperature, pH, and initial concentration. The synthesized porous nanocomposite adsorbent exhibited a high adsorption capacity of 473.2 mg g-1 and followed pseudo-second-order kinetics. Additionally, the maximum adsorption capacity was observed at an initial concentration of 534.9 mg g-1. The adsorbent was also sensitive to temperature changes and was well-described thermodynamically and isothermally by the Freundlich isotherm model. Two artificial neural networks (ANNs) were also developed to investigate the properties of the synthesized nanocomposites. In the first ANN, the properties of the nanocomposites, including pore size, porosity, compressive strength, and elastic modulus, were predicted based on the variations in the weight percentages of gelatin and hydroxyapatite. In the second ANN, the effects of changes in temperature and initial concentration on the adsorption of MB by the synthesized nanocomposite samples were predicted. The ANNs' predictions indicated that increasing the weight percentage of hydroxyapatite nanoparticles and gelatin enhances the physical, mechanical, and adsorption performance of the synthesized porous nanocomposites. The best results were achieved for the sample containing 40 wt % of gelatin and 30 wt % of hydroxyapatite nanoparticles. Furthermore, the ANN models demonstrated that increasing the temperature and initial concentration resulted in an increase in the amount of MB adsorbed.

New insights on the preparation of amine covalent organic polymer and its adsorption properties

Dye pollution is becoming increasingly severe. This study used the Schiff base reaction to synthesize a polyaromatic ring covalent organic polymer material with amide bonds and high electronegativity named SLEL-9 to adsorb Methylene Blue (MB) and Rhodamine B (RhB). SLEL-9 was characterized by Fourier transform infra-red spectra, X-ray photoelectron spectra, Brunauer-Emmett-Teller (BET), zeta potential analysis, and other techniques. It was found that SLEL-9 material contains C-C, CN, C-N, and CO. SLEL-9 had a zeta potential of about -45 mV under neutral conditions, which proved that the material had been synthesized successfully. The BET and Langmuir surface areas of SLEL-9 were 35.187 m2 g-1 and 56.419 m2 g-1, respectively. The adsorptions of SLEL-9 on low concentration (10 mg L-1) Methylene Blue and Rhodamine B reached equilibrium within 48 h. The results showed that SLEL-9's adsorption of dye molecules are more consistent with pseudo-second-order kinetic and Langmuir isotherm model. The adsorption experiments showed that the adsorption process is a spontaneous endothermic reaction, mainly chemisorption. The maximum adsorption capacity of SLEL-9 for MB and RhB were 132.45 mg g-1 and 101.94 mg g-1. In addition, this study investigated to determine the optimal reaction parameters. The primary mechanisms of SLEL-9 adsorption of two dyes are n→π* interaction, π-π EDA interaction and electrostatic attraction. Selective adsorb ability experiment results showed that SLEL-9 could selectively adsorb MB and RhB to a certain extent. Finally, it was found that SLEL-9 can maintain over 70% adsorption capacity after five reuses and can maintain stability after soaking in different pH water and organic solvents for 120 h. SLEL-9 proved to be a promising organic covalent polymer adsorption material for the removal of Methylene Blue and Rhodamine B in water.

CTAB-modified peanut husk pre-treated with KMnO4 as an eco-friendly adsorbent for the uptake of Congo red in solution: adsorption and mechanism study

A cationic surfactant (cetyltrimethylammonium bromide, CTAB)-modified peanut husk pretreated with potassium permanganate (KMnO4) was developed and applied as an adsorbent for the removal of Congo red (CR) in aqueous solution. The surface morphology and physicochemical characteristics of the adsorbent labelled as PNK-CTAB were assessed using well-established analytical techniques. The efficiency of PNK-CTAB was assessed via the batch adsorption method using distilled water, tap water and river water as aqueous medium. Results of the batch study showed that the adsorption capacity of PNK-CTAB could reach 70.5 mg g-1 at 313 K due to its improved surface properties and functionalities. Furthermore, the uptake of CR onto PNK-CTAB was found to be best described by the Elovich model thus suggesting adsorption on a heterogeneous surface, whereas fitting of intraparticle diffusion model indicated the significant role of mass transfer mechanism in the process. The equilibrium data was found to be well described by Langmuir, Temkin and Freundlich models albeit the latter was the best fit. Further analysis of the associated thermodynamics indicated the adsorption process to be endothermic, spontaneous in nature and likely mediated by physisorption processes. The excellent adsorption efficiency of PNK-CTAB toward CR within a wide pH range, negligible influence of some commonly occurring salts, good reusability efficiency, low cost (as confirmed by its cost analysis) and its ability to reduce the cytotoxicity of CR towards human embryonic kidney (HEK) 293 cells suggest the good prospects of this adsorbent for practical applications.

Synergistic approach for synthesis of functionalized biochar for efficient adsorption of Lopinavir from polluted water

The COVID-19 pandemic has led to a significant increase in antibiotic consumption, along with a 70% rise in antiviral drug concentrations in aquatic ecosystems. For the effective adsorption of antibiotics, biochar was modified by incorporating layered double hydroxide (LDH) through hydrothermal method. The results showed that LDH provides additional hydroxyl groups, positive surface charges and ion exchange. Whereas biochar component provides a larger specific surface area (467.8 m2/g). Batch adsorption experiments of biochar @ layered double hydroxide (BC@LDH) showed enhanced adsorption performance (832.9 mg/g), compared to pristine LDH (420.3 mg/g) and unmodified biochar (548.5 mg/g). Adsorption data were best interpreted (R2 = 0.99) by pseudo second order, Freundlich, and Temkin isotherm models. Adsorption was a synergism of LDH and biochar physiochemical properties, whereas pore-filling was the primary mechanism. The recyclability of BC@LDH confirmed its good structural stability. This study introduces a sustainable and efficient method for synthesizing a versatile adsorbent with superior antibiotic removal.

Unveiling the mechanistic aspects of methylene blue adsorption onto a novel phosphate-decorated coconut fiber lignin

The aim of this work was to evaluate the adsorptive performance of the phosphorylated coconut fiber lignin (PCFL) obtained through an innovative biorefinery process for removing methylene blue (MB). PCFL was obtained using coconut fiber mixed with 85 % wt. H3PO4 at 70 °C for 1 h. Milled wood lignin (MWL) and PCFL were characterized by FTIR, CP-MAS 31P NMR, phosphorous and hydroxyl contents, pHPZC, and BET analyses. The batch adsorption tests evaluated the effects of the biosorbent (0.25 - 4 g L-1) and adsorbate dosages (2.5 - 7.5 mg L-1), contact time (0 - 60 min), pH (4 - 8), ionic strength (0.001 - 0.1 mol L-1) and temperature (298.15 - 318.15 K) on MB adsorption. Kinetic, equilibrium, and thermodynamic modeling were used. The phosphorous content on PCFL was 2.5 times higher than that of MWL. PCFL presented an enhanced adsorptive performance for removing MB, which was spontaneous (ΔG0 < 0), endothermic (ΔH0 > 0), with affinity between the biosorbent and adsorbate (ΔS0 > 0), and driven by physisorption (Ea > 40 kJ mol-1). The adsorptive performance of PCFL was enhanced due to the grafting of new active sites by using an innovative biorefinery process, showing its potential to be used for textile effluent remediation.

Porous metal-organic framework-acrylamide-chitosan composite aerogels: Preparation, characterization and adsorption mechanism of azo anionic dyes adsorbed from water

Micro- and nano-metal-organic frameworks with different adsorption properties were prepared by a time-modulation hydrothermal method. By comparing the adsorption properties, the most effective MIL-68(Fe)-12 was selected to be mixed with chitosan (CS), and porous metal-organic framework-acrylamide-chitosan composite aerogel (PMACA) was prepared by introducing acrylamide prior to glutaraldehyde crosslinking. The adsorption capacity of PMACA doped with acrylamide was as high as 2086.44 mg·g-1. The adsorption performance of PMACA was 1.48 times higher compared to the porous metal-organic framework-chitosan composite aerogel (PMCA) undoped with acrylamide. With the introduction of acrylamide, the stability of PMACA was improved, making it less prone to dispersion and decomposition. Structural characterization and adsorption properties were analyzed using methods such as XRD, FTIR, TGA, SEM, BET, and Zeta potential. The adsorption performance of PMACA was investigated further through batch tests with variables such as adsorbent dosage, pH, contact time, initial CR solution concentration, and temperature. The model fitting of PMACA was consistent with the pseudo-second-order model and the Sips model. The adsorption thermodynamics showed that high temperature promoted spontaneous adsorption behavior. PMACA showed a recovery rate of approximately 86 % after six cyclic adsorption tests. PMACA maintained a recovery rate of roughly 86 % after six cyclic adsorption tests. The combined effects of electrostatic attraction, hydrogen bonding, and π-π conjugation resulted in excellent adsorption performance, while pore filling also contributed to the efficient adsorption of Congo red (CR).

Recent insights into mechanism of modified bio-adsorbents for the remediation of environmental pollutants

Rapid industrialization has exacerbated the hazard to health and the environment. Wide spectrums of contaminants pose numerous risks, necessitating their disposal and treatment. There is a need for further remediation methods since pollutant residues cannot be entirely eradicated by traditional treatment techniques. Bio-adsorbents are gaining popularity due to their eco-friendly approach, broad applicability, and improved functional and surface characteristics. Adsorbents that have been modified have improved qualities that aid in their adsorptive nature. Adsorption, ion exchange, chelation, surface precipitation, microbial uptake, physical entrapment, biodegradation, redox reactions, and electrostatic interactions are some of the processes that participate in the removal mechanism of biosorbents. These processes can vary depending on the particular biosorbent and the type of pollutants being targeted. The systematic review focuses on the many modification approaches used to remove environmental contaminants. Different modification or activation strategies can be used depending on the type of bio-adsorbent and pollutant to be remediated. Physical activation procedures such as ultrasonication and pyrolysis are more commonly used to modify bio-adsorbents. Ultrasonication process improves the adsorption efficiency by 15-25%. Acid and alkali modified procedures are the most effective chemical activation strategies for adsorbent modification for pollution removal. Chemical modification increases the removal to around 95-99%. The biological technique involving microbial culture is an emerging field that needs to be investigated further for pollutant removal. A short evaluation of modified adsorbents with multi-pollutant adsorption capability that have been better eliminated throughout the adsorption process has been provided.

Efficient synthesis and investigation of waste-derived adsorbent for water purification. Exploring the impact of surface functionalization on methylene blue dye removal

In pursuit of sustainable water management, the preparation of adsorbent materials via waste upcycling for water purification practices plays a decisive role. The sulphonated biochar, PiNe-SO3H, employed to target the methylene blue dye adsorption, was successfully synthesized via a mild, step-economical chemical carbonization-functionalization reaction. The presence of SO3H groups on the PiNe-SO3H surface played a critical role in significantly enhancing the adsorption capacity. The observed MB dye uptake was predominantly attributed to chemisorption processes as evidenced by the results from kinetics, thermodynamics, and isotherms. To further confirm the role of -SO3H in the adsorption mechanism, a comparison was made with other PiNe materials lacking sulphonic groups, highlighting the superior adsorption capacity of PiNe-SO3H. Additionally, a fast and efficient regeneration process was proposed to develop a truly waste minimized protocol, enabling the recovery of up to 94 % of the ethanolic mixture used during this step.

Enhancement in photocatalytic selectivity of TiO2-based nano-catalyst through molecular imprinting technology

Improvement in the photocatalytic selectivity is imperative for the effective and efficient utilization of catalysts. In this study, a molecularly imprinted polymer-coated iron-doped titanium dioxide (Fe-TiO2@MIP) nanocomposite was successfully synthesized by precipitation polymerization while using RB-19 as a template. The synthesized nanocomposites (Fe-TiO2@MIP and Fe-TiO2@NIP) were characterized by Fourier transform infrared spectroscopy (FT-IR), atomic force microscopy (AFM), field emission scanning electron microscopy (FESEM) with energy dispersive X-ray (EDX), X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Brunauer-EMMETT-Teller (BET), and UV-visible spectrophotometry. The optimized binding experiments revealed a high imprinting factor of 5.0 for RB-19. The catalytic degradation efficiency and selectivity of Fe-TiO2@MIP enhanced to almost complete degradation of RB-19 from 70% for the parent Fe-TiO2 and 76% for Fe-TiO2@NIP. An outstanding degradation selectivity of RB-19 was achieved compared to other competitive dyes. Finally, the analysis of the non-degraded and degraded RB-19 by ESI-MS revealed the presence of different intermediates that fits well with the proposed degradation mechanism. The study opens new possibilities of selective photo-degradation of targeted contaminants that may ultimately lead to efficient use of photocatalysts.

Preparation of amphoteric double network hydrogels based on low methoxy pectin: Adsorption kinetics and removal of anionic and cationic dyes

The objective of this research was to devise a functional hydrogel was synthesized using pectin (PE), acrylic acid (AA), dimethyldiallyl ammonium chloride (DC), and polyvinyl alcohol (PVA), designed to adsorb both cationic and anionic dyes concurrently. The low methoxy pectin formed double network hydrogel through chemical and physical crosslinking with AA and PVA respectively. DC is combined into the hydrogel system through copolymerization reaction. Analysis of hydrogel's physicochemical properties was conducted using techniques such as infrared spectroscopy, texture analysis, thermogravimetry, and scanning electron microscopy. Dyes adsorption studies showed that the LP/AA/DC/PVA-2 hydrogel, prepared at the molar ratio of AA to DC of 1:2, exhibited higher adsorption efficiency for methylene blue (MB) and Congo red (CR). Kinetics and isotherms studies indicated that the adsorption behavior conformed to the pseudo-second-order kinetic model and Langmuir isotherm model. By the Langmuir isotherm fitting, the maximum adsorption capacities of MB and CR by LP/AA/DC/PVA-2 were recorded to be 222.65 mg/g and 316.46 mg/g, respectively. The adsorption mechanism is dominated by the hydrogen bonding and electrostatic interactions. Further, the adsorption and desorption experiments demonstrated that LP/AA/DC/PVA-2 hydrogel have excellent reusability.

Synthesis of Mesoporous Eu3+-Doped Zinc/Silicate Phosphors for Highly Selective and Sensitive Detection of Sulfide Ions

A mesoporous Eu3+-doped zinc/silicate phosphor with a large surface area (>100 m2g-1) and amorphous structure was prepared in an aqueous solution without using any organic template. The residual concentration of the Zn2+ ion in the filtrate is lower than the standard of effluent 3.5 ppm under a pH 8-11 preparation condition. When a sulfide ion (S2-) is present in aqueous solution, the phosphor can react with the sulfide ion to transform from the amorphous structure to the crystalline ZnS, which causes structural transformation and a subsequent decrease in luminescent intensity. This distinct phosphor with a high surface area and amorphous structure can be applied through the structure transformation mechanism for highly selective and sensitive detection of the sulfide ions at low concentrations. In addition, the luminescent efficiency was obtained from adjustments in the pH value, calcination temperature, and Eu3+ ion concentration. The quenching efficiency, the limit of detection (CLOD), S2- ion selectivity, and phosphor regeneration ability were systematically explored in sulfide ion detection tests. Due to the novel S2- ion-induced structural transformation, we found that the amorphous Eu3+-doped zinc/silicate phosphors demonstrate a CLOD sensitivity as low as 1.8 × 10-7 M and a high Stern-Volmer constant (KSV) of 3.1 × 104 M-1. Furthermore, the phosphors were easily regenerated through simple calcination at 500 °C and showed a KSV value of 1.4 × 104 M-1. Overall, the Eu3+-doped zinc/silicates showed many advantageous properties for detecting sulfide ions, including low toxicity, green synthesis, good selectivity, high sensitivity, and good renewability.

Fabrication of biogenic carbon-based materials from coconut husk for the eradication of dye

The highly biocompatible nature of carbon dots (CQDs) and potential usage in waste water treatment makes them as one of the effective alternative for treating water pollution. Herein, biogenic carbon dots (CQDs) with size range of 2 nm were prepared from waste coconut husk as a precursor source. The hydrophilic nature and higher surface area of as prepared CQDs has further supported the superior adsorption efficiency of more than 90% for Victoria blue B (VB) dye from waste water samples. Different dye adsorption parameters including adsorbate and adsorbent dosage, pH of reaction media and equilibrium time have been optimized and found that 8 mg of adsorbent was sufficient to remove 70 mg VB dye in 4 mL aqueous solution in 60 min at pH = 7. The adsorption kinetic (2nd order) and isotherms (Freundlich-type) were well followed on prepared CQDs. The reusability studies up to 5 times with minimal decrement of 4% confirm the constancy of CQDs for the adsorptive removal of VB. The methodology presents a greener way for overcoming ecological issues with sustainable materials in an economical manner.

Decolorization of Textile Azo Dye via Solid-State Fermented Wheat Bran by Lasiodiplodia sp. YZH1

Textile dyes are one of the major water pollutants released into water in various ways, posing serious hazards for both aquatic organisms and human beings. Bioremediation is a significantly promising technique for dye decolorization. In the present study, the fungal strain Lasiodiplodia sp. was isolated from the fruiting bodies of Schizophyllum for the first time. The isolated fungal strain was examined for laccase enzyme production under solid-state fermentation conditions with wheat bran (WB) using ABTS and 2,6-Dimethoxyphenol (DMP) as substrates, then the fermented wheat bran (FWB) was evaluated as a biosorbent for Congo red dye adsorption from aqueous solutions in comparison with unfermented wheat bran. A Box-Behnken design was used to optimize the dye removal by FWB and to analyze the interaction effects between three factors: fermentation duration, pH, and dye concentration. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron microscopy (SEM) were applied to study the changes in the physical and chemical characteristics of wheat bran before and after fermentation. An additional experiment was conducted to investigate the ability of the Lasiodiplodia sp. YZH1 to remove Congo red in the dye-containing liquid culture. The results showed that laccase was produced throughout the cultivation, reaching peak activities of ∼6.2 and 22.3 U/mL for ABTS and DMP, respectively, on the fourth day of cultivation. FWB removed 89.8% of the dye (100 mg L-1) from the aqueous solution after 12 h of contact, whereas WB removed only 77.5%. Based on the Box-Behnken design results, FWB achieved 93.08% dye removal percentage under the conditions of 6 days of fermentation, pH 8.5, and 150 mg L-1 of the dye concentration after 24 h. The fungal strain removed 95.3% of 150 mg L-1 of the dye concentration after 8 days of inoculation in the dye-containing liquid culture. These findings indicate that this strain is a worthy candidate for dye removal from environmental effluents.

Removal of crystal violet dye using a three-dimensional network of date pits powder/sodium alginate hydrogel beads: Experimental optimization and DFT calculation

Biodegradable and very low-cost adsorbent beads were prepared from date pits powder (DP) and sodium alginate (SA). DP to SA ratios was varied (1/2, 1/4 and 1/6) and used to eliminate Crystal violet (CV) a cationic dye. Adsorbents were characterized by FTIR, SEM-EDS, UV-vis DR, TGA and the point of zero charge (pHPZC). The optimal composite beads SA@6DP show high adsorption capacities of 83.565 mg/g toward CV than SA@2DP and SA@4DP. The kinetics investigation showed that the adsorption is well described by the pseudo-second-order kinetic (R2 = 0.998). The thermodynamics and isotherms studies exhibit that the adsorption phenomenon for SA@6DP adsorbent is endothermic and significantly fitted with the Redlich-Peterson model. The experimental adsorption tests were optimized by the Box-Behnken design (BBD) which led to conclude the maximal CV removal efficiency achieved by SA@6DP was 99.873 % using [CV] = 50 mg/L, adsorbent mass = 20 mg and 48 h of contact time. The theoretical calculation proved that the CV molecules favor the mode of attack due to their electrophilic character and can accept the SA@6DP adsorbent electrons more easily to form an anti-bonding orbital. SA@6DP hydrogel beads are therefore an exceptional bio-adsorbent that offers excellent adsorption performance.

Photo-induced adsorption-desorption behavior of methylene blue on CA-BMO under visible light irradiation

In this work, the modification of Bi2MoO6 with critic acid (CA-BMO) to achieve enhanced adsorption of methylene blue (MB) solution in dark and desorption under visible light irradiation was reported. The as-prepared materials were synthesized by a hydrothermal method and characterized via SEM, FT-IR, XRD, and XPS techniques. Only 16.5% of 10 mg L-1 MB was removed within 10 min by using 0.5 g L-1 Bi2MoO6, while 92.9% removal of MB could be achieved by using 0.5 g L-1 CA-BMO, which enhanced the adsorption removal by a factor of 4.6. The adsorption capacity for MB was 18.9 mg g-1. Desorption efficiency of MB was only observed in CA-BMO system, and it depends on the wavelength of the light source, pH, and the presence of metal ions. Characterization results suggested that carboxyl groups, which were modified onto the surface of Bi2MoO6, could serve as adsorption sites for MB, and the connections were damaged under light, thus leading to the desorption of MB from the surface of the CA-BMO. This study provides a novel reagent-free desorption strategy for dye recovery without secondary pollution, which facilitates the development and application of Bi-based adsorbent for dye-containing wastewater treatment.

Adsorption of methyl orange on low-cost adsorbent natural materials and modified natural materials: a review

Recently a large number of extensive studies have amassed that describe the removal of dyes from water and wastewater using natural adsorbents and modified materials. Methyl orange dye is found in wastewater streams from various industries that include textiles, plastics, printing and paper among other sources. This article reviews methyl orange adsorption onto natural and modified materials. Despite many techniques available, adsorption stands out for efficient water and wastewater treatment for its ease of operation, flexibility and large-scale removal of colorants. It also has a significant potential for regeneration recovery and recycling of adsorbents in comparison to other water treatment methods. The adsorbents described herein were classified into five categories based on their chemical composition: bio-sorbents, activated carbon, biochar, clays and minerals, and composites. In this review article, we want to demonstrate the capacity of natural and modified materials for dye adsorption which can yield significant improvements to the adsorption capacity of dyes such as methyl orange. In addition, the effect of critical variables including contact time, initial methyl orange concentration, dosage of adsorbent, pH, temperature and mechanism on the adsorption efficiency will be covered as part of this literature review.

Indigo Carmine: Between Necessity and Concern

Dyes, such as indigo carmine, have become indispensable to modern life, being widely used in the food, textile, pharmaceutical, medicine, and cosmetic industry. Although indigo carmine is considered toxic and has many adverse effects, it is found in many foods, and the maximum permitted level is 500 mg/kg. Indigo carmine is one of the most used dyes in the textile industry, especially for dyeing denim, and it is also used in medicine due to its impressive applicability in diagnostic methods and surgical procedures, such as in gynecological and urological surgeries and microsurgery. It is reported that indigo carmine is toxic for humans and can cause various pathologies, such as hypertension, hypotension, skin irritations, or gastrointestinal disorders. In this review, we discuss the structure and properties of indigo carmine; its use in various industries and medicine; the adverse effects of its ingestion, injection, or skin contact; the effects on environmental pollution; and its toxicity testing. For this review, 147 studies were considered relevant. Most of the cited articles were those about environmental pollution with indigo carmine (51), uses of indigo carmine in medicine (45), and indigo carmine as a food additive (17).

Novel Capturer-Catalyst Microreactor System with a Polypyrrole/Metal Nanoparticle Composite Incorporated in the Porous Honeycomb-Patterned Film

A composite of polypyrrole/metal nanoparticles (PPy/MNPs) was selectively incorporated into the pores of a honeycomb-patterned porous polycaprolactone polymer film to fabricate a novel capturer-catalyst microreactor system. This fabrication involved a modified breath figure method, where the polymer solution containing metal ions as an oxidizing agent was cast under humid conditions along with the pyrrole monomer through an interfacial reaction in a one-step in situ process. The higher hydrophilicity of the metal ions compared to the polymer solution led to their self-assembly around the pore surface, resulting in the selective incorporation of the PPy/MNP composite into the porous film. Copper (Cu), silver (Ag), and gold (Au) were used for the PPy/MNP fabrication. Various methods characterized the fabricated film. Strong catalytic degradations of methylene blue and methyl orange were obtained with PCL-PPy/MNPs. Recycling experiments showed no loss of activity even after five cycles of recycling. Comparative analysis of PCL-PPy, PCL-MNP, and PCL-PPy/MNP results indicated the synergistic action of PPy and MNPs in dye degradation. High-performance liquid chromatography and mass spectroscopy analyses confirmed dye degradation after treatment with a fabricated microreactor. PPy might have acted as a capturer of the dye molecule and MNPs as a catalyst, thereby enhancing the efficiency of dye degradation. Additionally, the PCL-PPy/Cu composite exhibited strong antimicrobial properties against Gram-positive (Staphylococcus aureus) and Gram-negative bacteria (Escherichia coli) with no cytotoxicity as measured by the MTT assay. Therefore, the fabricated microreactor film has promising applications in various fields.

Optimization of LDO-Pectin Synthesis Conditions for the Removal of Metals from Wastewater: A Comparison of Response Surface Methods and Taguchi Approaches

With the continuous growth of industrialization, the presence of heavy metals (HMs) in the environment has become a critical issue, necessitating cost-effective and efficient techniques for their removal. The present study aimed to determine the optimal preparation conditions for synthesizing pectin (PC) as a polymer sorbent, combined with Magnesium (Mg) Aluminum (Al) layered double oxides (LDOs), using a fast and facile co-precipitation method. Both the response surface method (RSM) and the Taguchi method were employed to optimize the influence of key independent variables, including the molar ratio of cations Mg:Al, the ratio of pectin to LDO, and the temperature for removing multiple elements from wastewater. The results indicated that RSM is more accurate and examines more interactions, while Taguchi reduces the number of tests and is more economical than RSM. However, both statistical methods showed good potential for predicting the adsorption capacity (Qe) of HMs. The optimal preparation conditions were identified as a molar ratio of 3:1, a ratio of pectin to LDO of 7% w/w, and a temperature of approximately 600 °C. In conclusion, the application of RSM and Taguchi approaches was found to be feasible and effective in optimizing the preparation conditions of modified LDO, which can be utilized as a potential adsorbent for removing multiple elements from wastewater.

Reusable flexible poly(vinyl alcohol)/chitosan-based polymer carbon dots composite film for acid blue 93 dye adsorption

The design and synthesis of water-insoluble chitosan-based polymer carbon dots [P(CS-g-CA)CDs] are described. A polyvinyl alcohol/chitosan-based polymer carbon dot [PVA/P(CS-g-CA)CDs] composite film was prepared using a simple casting method to be used in dye adsorption. The composite film was characterized using FT-IR, XPS, transparency, contact angle, and mechanical properties tests, which showed the successful incorporation of P(CS-g-CA)CDs into the film and also revealed that hydrogen bonding improved the mechanical properties of the PVA film. Furthermore, the composite film displayed substantially enhanced hydrophobicity, making it suitable for use in aqueous environments. In addition, the composite film exhibited stable adsorption of acid blue 93 (AB93) at pH 2-9, with an enhanced adsorption capacity of 433.24 mg/g. The adsorption obeyed Langmuir law with an efficiency of more than 89% even after five cycles. Therefore, the PVA/P(CS-g-CA)CDs film is a promising material for the treatment of organic dye-polluted wastewater.