Device-assisted transdermal drug delivery

Controlled Transdermal Iontophoresis of Insulin from Water-Soluble Polypyrrole Nanoparticles: An In Vitro Study

The iontophoresis delivery of insulin (INS) remains a serious challenge due to the low permeability of the drug through the skin. This work aims to investigate the potential of water-soluble polypyrrole nanoparticles (WS-PPyNPs) as a drug donor matrix for controlled transdermal iontophoresis of INS. WS-PPyNPs have been prepared via a simple chemical polymerization in the presence of sodium dodecyl sulfate (SDS) as both dopant and the stabilizing agent. The synthesis of the soluble polymer was characterized using field emission scanning electron microscopy (FESEM), dynamic light scattering (DLS), fluorescence spectroscopy, and Fourier transform infrared (FT–IR) spectroscopy. The loading mechanism of INS onto the WS-PPyNPs is based on the fact that the drug molecules can be replaced with doped dodecyl sulfate. A two-compartment Franz-type diffusion cell was employed to study the effect of current density, formulation pH, INS concentration, and sodium chloride concentration on anodal iontophoresis (AIP) and cathodal iontophoresis (CIP) of INS across the rat skin. Both AIP and CIP delivery of INS using WS-PPyNPs were significantly increased compared to passive delivery. Furthermore, while the AIP experiment (60 min at 0.13 mA cm^–2) show low cumulative drug permeation for INS (about 20.48 µg cm⁻²); the CIP stimulation exhibited a cumulative drug permeation of 68.29 µg cm⁻². This improvement is due to the separation of positively charged WS-PPyNPs and negatively charged INS that has occurred in the presence of cathodal stimulation. The obtained results confirm the potential applicability of WS-PPyNPs as an effective approach in the development of controlled transdermal iontophoresis of INS.

Microneedle system: a modulated approach for penetration enhancement

The microneedles show advantages over transdermal drug delivery systems on account of better skin permeation bypassing the stratum corneum. To increase the flux of permeation, penetration enhancement techniques like physical and chemical methods are combined with a trans-epidermal delivery system across the skin causing minimal pain. These techniques include iontophoresis, sonophoresis, and electroporation for physical enhancement of drug delivery via topical route by either disrupting the structure of the stratum corneum or by creating pores/micro-channels within the skin. The use of chemical penetrants such as ethanol, lipids, surfactants, and terpenes improves the release kinetics by mechanisms like fluidization of lipids, denaturation of proteins, etc. A combination of microneedles and these techniques show a significant increase in the permeability of drugs across the skin by 5-10 times compared to microneedles alone. This review article focuses on various advanced strategies like the use of drug-polymer complexes, application of ultrasound frequency or tolerable electric current, formation of nano-formulations, etc. with microneedle delivery for transportation of high payload of actives, macromolecules, antibodies, gene, proteins, and peptides. In the near future, microneedle systems will offer potential targeted drug delivery, self-sealable administration across the skin, and minimally invasive vaccine transportation in cancer, diabetes, Alzheimer's, and cardiovascular diseases.HighlightsPhysical penetration enhancement techniques: iontophoresis, electroporation, and sonophoresis.Chemical penetration enhancers: polymers, lipids, surfactants.Strategies to use microneedle system with penetration enhancement techniques.The significant difference in the penetration ability of high payload actives.

Versatile Ice Microneedles for Transdermal Delivery of Diverse Actives

Microneedles are regarded as an emerging and promising transdermal drug delivery strategy. Great efforts are devoted to getting rid of their material restrictions and imparting them with abilities to carry various drugs. Here, inspired by ice formation in nature and based on characteristics of different frozen materials, the authors present novel ice microneedles made from versatile soft materials using a simple freezing template-based fabrication stratagem for effective transdermal delivery of diverse actives. Their strategy can convert microneedles with almost all water-containing components from softness into hardness for guaranteeing satisfactory penetration, thus removing their material component limitations. As all fabrication procedures are mild and actives can maintain activity during these processes, the ice microneedles can carry and deliver various actives from small molecules and macromolecules to even living organisms. They have demonstrated that these ice microneedles can easily penetrate mouse and swine skins using a microneedle injector, with their active-carried tips left inside after their ice base melts. Thus, by loading heparin, erythropoietin, or biosafe Bacillus subtilis (B. subtilis) inside the ice microneedles to treat mouse models, the practical values of these microneedles are well displayed, indicating their bright prospects in universal drug delivery systems.

Nanofiber as a novel vehicle for transdermal delivery of therapeutic agents: challenges and opportunities

Background

Transdermal delivery of drugs is a quite challenging task for pharmaceutical scientists. The transdermal route is preferred over the oral route due to various advantages like avoidance of the first-pass effect, non-invasiveness, and high patient compliance. Therefore, it is necessary to develop an effective carrier system that enables the effective passage of the drug through the dermal barrier.

Main body of abstract

Various novel drug delivery systems are used to enhance the permeation of a variety of drugs through the skin barrier. Researchers around the globe have explored nanofibers for the transdermal delivery of various therapeutic agents. Nanofibers are designed to have a high concentration of therapeutic agents in them promoting their flux through various skin layers. Polymeric nanofibers can be explored for the loading of both hydrophilic and lipophilic drugs. Biopolymer-based nanofibers have been also explored for transdermal delivery. They are capable of controlling the release of therapeutic agents for a prolonged time.

Short conclusion

The literature presented in this review paper provides significant proof that nanofibers will have an intense impact on the transdermal delivery of different bioactive molecules in the future.

Graphic abstract

A Comprehensive Review of Microneedles: Types, Materials, Processes, Characterizations and Applications

Drug delivery through the skin offers many advantages such as avoidance of hepatic first-pass metabolism, maintenance of steady plasma concentration, safety, and compliance over oral or parenteral pathways. However, the biggest challenge for transdermal delivery is that only a limited number of potent drugs with ideal physicochemical properties can passively diffuse and intercellularly permeate through skin barriers and achieve therapeutic concentration by this route. Significant efforts have been made toward the development of approaches to enhance transdermal permeation of the drugs. Among them, microneedles represent one of the microscale physical enhancement methods that greatly expand the spectrum of drugs for transdermal and intradermal delivery. Microneedles typically measure 0.1-1 mm in length. In this review, microneedle materials, fabrication routes, characterization techniques, and applications for transdermal delivery are discussed. A variety of materials such as silicon, stainless steel, and polymers have been used to fabricate solid, coated, hollow, or dissolvable microneedles. Their implications for transdermal drug delivery have been discussed extensively. However, there remain challenges with sustained delivery, efficacy, cost-effective fabrication, and large-scale manufacturing. This review discusses different modes of characterization and the gaps in manufacturing technologies associated with microneedles. This review also discusses their potential impact on drug delivery, vaccine delivery, disease diagnostic, and cosmetics applications.

An overview on the advantages and limitations of 3D printing of microneedles

The use of 3D printing (3DP) technology, which has been continuously evolving since the 1980s, has recently become common in healthcare services. The introduction of 3DP into the pharmaceutical industry particularly aims at the development of patient-centered dosage forms based on structure design. It is still a new research direction with potential to create the targeted release of drug delivery systems in freeform geometries. Although the use of 3DP technology for solid oral dosage forms is more preferable, studies on transdermal applications of the technology are also increasing. Microneedle sequences are one of the transdermal drug delivery (TDD) methods which are used to bypass the minimally invasive stratum corneum with novel delivery methods for small molecule drugs and vaccines. Microneedle arrays have advantages over many traditional methods. It is attractive with features such as ease of application, controlled release of active substances and patient compliance. Recently, 3D printers have been used for the production of microneedle patches. After giving a brief overview of 3DP technology, this article includes the materials necessary for the preparation of microneedles and microneedle patches specifically for penetration enhancement, preparation methods, quality parameters, and their application to TDD. In addition, the applicability of 3D microneedles in the pharmaceutical industry has been evaluated.

Strategies for Browning Agent Delivery

Obesity expands as a global climbing epidemic that is often correlated to cardiovascular diseases and endocrine disorders. Converting white adipocytes to brown adipocytes for enhanced energy expenditure has recently emerged as a promising anti-obesity treatment. However, the conventional approaches to apply browning agents systematically suffer from off-target effects, multiple dosage requirements, and poor patient compliance. To date, various delivery strategies have been reported to deliver browning agents for obesity treatment in a safer and more controllable manner. This review will discuss the latest designs in browning agent delivery systems with a focus on nanomedicines and transdermal patches.

Observation and Mitigation of Leachables from Non-Product Contact Materials in Electromechanical Delivery Devices for Biotechnology Products

Battery-powered drug delivery devices are widely used as primary containers for storing and delivering therapeutic protein products to improve patient compliance and quality of life. Compared to conventional delivery approaches such as pre-filled syringes, battery-powered devices are more complex in design requiring new materials/components for proper functionality, which could cause potential product safety and quality concerns from the extractable and leachables (E&L) of the new materials/components. In this study, E&L assessments were performed on a battery-powered delivery device during the development and qualification of the device, where novel compound 2‑hydroxy-2-methylpropiophenone (HMPP) and related compounds were observed in both E&L. The source of the HMPP and related compounds was identified to be the nonproduct contact device batteries, in which HMPP photo-initiator was used as a curing agent in the battery sealant to prevent leakage of the battery electrolytes. Toxicology assessment was performed, which showed the levels of HMPP observed in the device lots were acceptable relative to the permitted daily exposure. A drug product HMPP spike study was also performed, where no product impact was observed. Based on these assessments, an action threshold and specification limits could be established as a control strategy, if needed, to mitigate the potential risks associate with the observed leachables. As a full resolution, seven battery candidates from different suppliers were screened and one new battery was successfully qualified for the delivery devices. Overall, the holistic E&L approach was fully successful in the development and qualification of the battery-powered devices for biotherapeutic products delivery ensuring product quality and patient safety. Non-product contact materials are commonly rated as low or no risk and typically considered as out of scope of E&L activities for delivery systems following industry benchmark and regulatory agency guidance. This case study is novel as it brings into attention the materials that might not normally be in consideration during the development process. It is highly recommended to understand materials in the context of intended use on a case-by-case basis and not to generalize to ensure successful development and qualification.

The combination of medical devices and medicinal products revisited from the new European legal framework

Medical devices and medicinal products have many similarities in their nature, scope or specific medical purposes, and despite the differences in their principal means of action, they are often used in combination. Indeed, many medicinal products depend on medical devices for their administration, and it is increasingly common for medical devices to contain medicinal substances to support their action. Therefore, the combination of medicinal products and medical devices provides additional benefits for patients. However, their higher technical complexity requires a strengthening of their authorisation and certification requirements. In this regard, more comprehensive requirements and classification rules are introduced by a new European regulation on medical devices that fully applies from May 26^th 2021. On account of their therapeutic significance, this review aims at gaining insight into the borderline between medical devices and medicinal products in this new 2021 regulatory framework. For the first time, any item containing a medical device and a medicinal product will have both parts evaluated. Through exemplification of both marketed and investigational devices incorporating medicinal substances and drug-device combinations, the new European requirements and their implications are thoroughly illustrated herein.

Ultrasensitive fluorescence immunosensor based on mesoporous silica and magnetic nanoparticles: Capture and release strategy

Herein we designed a novel, highly sensitive, simple and amplified fluorescence immunosensing strategy for hepatitis B virus surface antigen (HBV surface antigen) (HBsAg) as a model based on the construction of a sandwich type probe. The operation mechanism of this immunosensing strategy is implemented by capturing and then stimulation-based-releasing of entrapped dye in the fluorescent capsules. The proposed probe is made by the Fe₃O₄ magnetic nanoparticle (Fe₃O₄ MNP) as a probe collector site and the Rhodamine B loaded-mesoporous silica nanoparticle (MSN-Rh.B) as a fluorescent mesoporous capsule and signal amplifier site. Such a methodology is benefited, from the advantages of the high ability of MSNs to be used as a scaffold for efficient dye encapsulation and the magnetic nanoparticles as efficient biological carriers. Under optimal conditions, the fluorescence signal (The fluorescence of solutions was measured using a quartz fluorescence cell (PMT voltage:720, Ex wavelegth:540, Em wavelength:568, All measurements were carried out at room temperature) increased with the increment of HBsAg concentration in the linear dynamic range of 6.1 ag/ml to 0.012 ng/ml with a detection limit (LOD) of 5.7 ag/ml. The relative standard deviation, measured between the resulting fluorescence peaks was obtained by 6.0%.

Pharmaceutical Perspective in Wearable Drug Delivery Systems

Humans have been dealing with health problems for millions of years. Normal health services need well-trained personnel and high-cost diagnostic tests, which forces patients to go to hospitals if medical treatment is required. To address this, prototype testing has been carried out into the wearable drug delivery health care perspectives. Researchers have devised a wide variety of formulations for the treatment of various diseases at home by performing real-time monitoring of different routes of drug administration such as ocular, transdermal, intraoral, intracochlear, and several more. A comprehensive review of the different types of wearable drug delivery systems with respect to their manufacturing, mechanism of action and specifications has been done. In the pharmaceutical context, these devices are technologically well-equipped interfaces for diverse physicochemical signals. Above mentioned information with a broader perspective has also been discussed in this article. Several wearable drug delivery systems have been introduced in the market in recent years. But a lot of testing needs to be conducted to address the numerous obstacles before the wearable devices are successfully launched in the market.

Physical methods for enhancing drug absorption from the gastrointestinal tract

Overcoming the gastrointestinal (GI) barriers is a formidable challenge in the oral delivery of active macromolecules such as peptide- and protein- based drugs. In the past four decades, a plethora of formulation strategies ranging from permeation enhancers, nanosized carriers, and chemical modifications of the drug's structure has been investigated to increase the oral absorption of these macromolecular compounds. However, only limited successes have been achieved so far, with the bioavailability of marketed oral peptide drugs remaining generally very low. Recently, a few approaches that are based on physical interactions, such as magnetic, acoustic, and mechanical forces, have been explored in order to control and improve the drug permeability across the GI mucosa. Although in the early stages, some of these methods have shown great potential both in terms of improved bioavailability and spatiotemporal delivery of drugs. Here, we offer a concise, yet critical overview of these rather unconventional technologies with a particular focus on their potential and possible challenges for further clinical translation.

A Fully Integrated Closed-Loop System Based on Mesoporous Microneedles-Iontophoresis for Diabetes Treatment

A closed-loop system that can mini-invasively track blood glucose and intelligently treat diabetes is in great demand for modern medicine, yet it remains challenging to realize. Microneedles technologies have recently emerged as powerful tools for transdermal applications with inherent painlessness and biosafety. In this work, for the first time to the authors' knowledge, a fully integrated wearable closed-loop system (IWCS) based on mini-invasive microneedle platform is developed for in situ diabetic sensing and treatment. The IWCS consists of three connected modules: 1) a mesoporous microneedle-reverse iontophoretic glucose sensor; 2) a flexible printed circuit board as integrated and control; and 3) a microneedle-iontophoretic insulin delivery component. As the key component, mesoporous microneedles enable the painless penetration of stratum corneum, implementing subcutaneous substance exchange. The coupling with iontophoresis significantly enhances glucose extraction and insulin delivery and enables electrical control. This IWCS is demonstrated to accurately monitor glucose fluctuations, and responsively deliver insulin to regulate hyperglycemia in diabetic rat model. The painless microneedles and wearable design endows this IWCS as a highly promising platform to improve the therapies of diabetic patients.

Biocompatible Nanotransfer Printing Based on Water Bridge Formation in Hyaluronic Acid and Its Application to Smart Contact Lenses

Many conventional micropatterning and nanopatterning techniques employ toxic chemicals, rendering them nonbiocompatible and unsuited for biodevice production. Herein the formation of water bridges on the surface of hyaluronic acid (HA) films is exploited to develop a transfer-based nanopatterning method applicable to diverse structures and materials. The HA film surface, made deformable via water bridge generation, is brought into contact with a functional material and subjected to thermal treatment, which results in film shrinkage, allowing a robust pattern transfer. The proposed biocompatible method, which avoids the use of extra chemicals, enables the transfer of nanoscale, microscale, and thin-film structures as well as functional materials such as metals and metal oxides. A nanopatterned HA film is transferred onto a moisture-containing contact lens to fabricate smart contact lenses with unique optical characteristics of rationally designed optical nanopatterns. These lenses demonstrated binocular parallax-induced stereoscopy via nanoline array polarization and acted as cutoff filters, with nanodot arrays, capable of treating Irlen syndrome.

Recent advances in transdermal drug delivery systems: a review

Various non-invasive administrations have recently emerged as an alternative to conventional needle injections. A transdermal drug delivery system (TDDS) represents the most attractive method among these because of its low rejection rate, excellent ease of administration, and superb convenience and persistence among patients. TDDS could be applicable in not only pharmaceuticals but also in the skin care industry, including cosmetics. Because this method mainly involves local administration, it can prevent local buildup in drug concentration and nonspecific delivery to tissues not targeted by the drug. However, the physicochemical properties of the skin translate to multiple obstacles and restrictions in transdermal delivery, with numerous investigations conducted to overcome these bottlenecks. In this review, we describe the different types of available TDDS methods, along with a critical discussion of the specific advantages and disadvantages, characterization methods, and potential of each method. Progress in research on these alternative methods has established the high efficiency inherent to TDDS, which is expected to find applications in a wide range of fields.

Development and Characterization of n-Propyl Gallate Encapsulated Solid Lipid Nanoparticles-Loaded Hydrogel for Intranasal Delivery

The objective of the present study was to develop n-propyl gallate-loaded solid lipid nanoparticles (PG-SLNs) in a hydrogel (HG) formulation using Transcutol-P (TC-P) as a permeation enhancer. Modified solvent injection technique was applied to produce optimized PG-SLNs via the Quality by Design approach and central composite design. The in vitro mucoadhesion, scavenging activity, drug release, permeation studies of PG from PG-SLNs-loaded HG were evaluated under simulated nasal conditions. Compared with in vitro release behavior of PG from SLNs, the drug release from the PG-SLNs-loaded HG showed a lower burst effect and sustained release profile. The cumulative permeation of PG from PG-SLNs-loaded HG with TC-P was 600 μg/cm² within 60 min, which is 3–60-fold higher than PG-SLNs and native PG, respectively. Raman mapping showed that the distribution of PG-SLNs was more concentrated in HG having lower concentrations of hyaluronic acid. The scavenging assay demonstrated increased antioxidant activity at higher concentrations of HG. Due to enhanced stability and mucoadhesive properties, the developed HG-based SLNs can improve nasal absorption by increasing residence time on nasal mucosa. This study provides in vitro proof of the potential of combining the advantages of SLNs and HG for the intranasal delivery of antioxidants.

Dopamine/zinc oxide doped poly(N-hydroxyethyl acrylamide)/agar dual network hydrogel with super self-healing, antibacterial and tissue adhesion functions designed for transdermal patch

Dual network (DN) hydrogels with excellent mechanical strength and controllable component adjustment characteristics have a broad application range in the field of biomedicine. However, the tissue adhesion, skin affinity, self-healing, and antibacterial properties of DN hydrogels are inadequate for their application as skin patches. In this work, we prepared dopamine/zinc oxide (DOPA/ZnO) doped poly(N-hydroxyethyl acrylamide) (p(HEAA))/agar DN hydrogels and combined them to obtain a bilayer hydrogel (two-layer gel) with moisturizing properties. Upon incorporating 0.86 wt% of dopamine (DOPA), the resultant DOPA/p(HEAA))/agar DN hydrogel (DOPA@DNG) exhibited high tensile strain (up to 1600%), excellent self-repair ability, and tissue adhesion. ZnO/p(HEAA))/agar DN hydrogel (ZnO NG) obtained by incorporating 2 w/v ZnO nanoparticles (ZnO NPs) achieved high tensile strength (1.2 MPa), good antibacterial ability, and low charge transfer resistance. Moreover, ZnO NG, which has a tight structure, was employed as a protective layer for the two-layer gel, which can effectively slow down the excessive evaporation of water to protect the DOPA@DNG stability as a skin patch. Evidence showed that the two-layer hydrogel has water retention. Water retention still remains at over 50% after keeping the hydrogel in air for 3 days. These properties mean the two-layer gel based on the DOPA/ZnO doped DN hydrogels could be used as a transdermal patch for numerous applications in drug delivery, wearable devices, and electronic skin.

Effect of Iontophoresis on the Intradermal Migration Rate of Medium Molecular Weight Drugs

The purpose of the present study was to evaluate whether iontophoresis (IP) accelerates the intradermal migration rate of medium molecular weight drugs. Sodium polystyrene sulfonate (PSA) and fluorescein isothiocyanate-dextran (FD) were used as model medium molecular weight acidic and non-electrolyte drugs, respectively. Low molecular weight acid and non-electrolyte drugs were also used for comparison. Drug-loaded excised split-layered skin (SL skin) was used in the experiment. SL skin was prepared using (i) whole skin was split once, (ii) the drug solution was applied on the lower skin, and (iii) the upper skin was layered onto the lower skin containing the drug solution as in the original skin. The effect of constant-current cathodal or anodal IP was applied to the SL skin, and the time course of the cumulative amount of drug migration from the SL skin through the dermis to the receiver was followed. In cases without IP and with anodal IP, the intradermal migration rates of medium molecular weight drugs were much lower than those of small molecules. The driving force for drug migration was thought to be simple diffusion through the skin layer. In contrast, cathodal IP significantly increased the intradermal migration rate of PSA not but of FD or low molecular weight drugs. This IP-facilitated migration of PSA was probably due to electrorepulsion. These results suggest that IP can be used to increase the intradermal migration of medium molecular weight charged drugs.

Modulating the foreign body response of implants for diabetes treatment

Diabetes Mellitus is a group of diseases characterized by high blood glucose levels due to patients' inability to produce sufficient insulin. Current interventions often require implants that can detect and correct high blood glucose levels with minimal patient intervention. However, these implantable technologies have not reached their full potential in vivo due to the foreign body response and subsequent development of fibrosis. Therefore, for long-term function of implants, modulating the initial immune response is crucial in preventing the activation and progression of the immune cascade. This review discusses the different molecular mechanisms and cellular interactions involved in the activation and progression of foreign body response (FBR) and fibrosis, specifically for implants used in diabetes. We also highlight the various strategies and techniques that have been used for immunomodulation and prevention of fibrosis. We investigate how these general strategies have been applied to implants used for the treatment of diabetes, offering insights on how these devices can be further modified to circumvent FBR and fibrosis.

Printable elastomeric electrodes with sweat-enhanced conductivity for wearables

We rationally synthesized the thermoplastic and hydrophilic poly(urethane-acrylate) (HPUA) binder for a type of printable and stretchable Ag flakes-HPUA (Ag-HPUA) electrodes in which the conductivity can be enhanced by human sweat. In the presence of human sweat, the synergistic effect of Cl- and lactic acid enables the partial removal of insulating surfactant on silver flakes and facilitates sintering of the exposed silver flakes, thus the resistance of Ag-HPUA electrodes can be notably reduced in both relaxed and stretched state. The on-body data show that the resistance of one electrode has been decreased from 3.02 to 0.62 ohm during the subject's 27-min sweating activity. A stretchable textile sweat-activated battery using Ag-HPUA electrodes as current collectors and human sweat as the electrolyte was constructed for wearable electronics. The enhanced conductivity of the wearable wiring electrode from the reaction with sweat would provide meritorious insight into the design of wearable devices.

Microarray patches: Breaking down the barriers to contraceptive care and HIV prevention for women across the globe

Despite the existence of a variety of contraceptive products for women, as well as decades of research into the prevention and treatment of human immunodeficiency virus (HIV), there is still a globally unmet need for easily accessible, acceptable, and affordable products to protect women's sexual and reproductive health. Microarray patches (MAPs) are a novel platform being developed for the delivery of hormonal contraception and antiretroviral drugs. MAPs provide enhanced drug delivery to the systemic circulation via the transdermal route when compared to transdermal patches, oral and injectable formulations. These minimally invasive patches can be self-administered by the user, reducing the burden on health care personnel. Since MAPs represent needle-free drug delivery, no sharps waste is generated after application, thereby eliminating possible MAP reuse and risk of needle-stick injuries. This review discusses the administration of contraceptive and antiretroviral drugs using MAPs, their acceptability by end-users, and the future perspective of the field.

Wearable patch delivery system for artificial pancreas health diagnostic-therapeutic application: A review

The advanced stimuli-responsive approaches for on-demand drug delivery systems have received tremendous attention as they have great potential to be integrated with sensing and multi-functional electronics on a flexible and stretchable single platform (all-in-one concept) in order to develop skin-integration with close-loop sensation for personalized diagnostic and therapeutic application. The wearable patch pumps have evolved from reservoir-based to matrix patch and drug-in-adhesive (single-layer or multi-layer) type. In this review, we presented the basic requirements of an artificial pancreas, surveyed the design and technologies used in commercial patch pumps available on the market and provided general information about the latest wearable patch pump. We summarized the various advanced delivery strategies with their mechanisms that have been developed to date and representative examples. Mechanical, electrical, light, thermal, acoustic and glucose-responsive approaches on patch form have been successfully utilized in the controllable transdermal drug delivery manner. We highlighted key challenges associated with wearable transdermal delivery systems, their research direction and future development trends.

Energy-Dependent Endocytosis Is Responsible for Skin Penetration of Formulations Based on a Combination of Indomethacin Nanoparticles and l-Menthol in Rat and Göttingen Minipig

We previously designed a Carbopol gel formulation (N-IND/MEN) based on a combination of indomethacin solid nanoparticles (IND-NPs) and l-menthol, and we reported that the N-IND/MEN showed high transdermal penetration. However, the detailed mechanism for transdermal penetration of IND-NPs was not clearly defined. In this study, we investigated whether endocytosis in the skin tissue of rat and Göttingen minipig is related to the transdermal penetration of IND-NPs using pharmacological inhibitors of endocytosis. The pharmacological inhibitors used in this study are as follows: 54 µM nystatin, a caveolae-mediated endocytosis (CavME) inhibitor; 40 µM dynasore, a clathrin-mediated endocytosis (CME) inhibitor; and 2 µM rottlerin, a micropinocytosis (MP) inhibitor. The N-IND/MEN was prepared by a bead mill method, and the particle size of solid indomethacin was 79–216 nm. In both rat and Göttingen minipig skin, skin penetration of approximately 80% IND-NPs was limited by the stratum corneum (SC), although the penetration of SC was improved by the combination of l-menthol. On the other hand, the treatment of nystatin and dynasore decreased the transdermal penetration of indomethacin in rats and Göttingen minipigs treated with N-IND/MEN. Moreover, in addition to nystatin and dynasore, rottlerin attenuated the transdermal penetration of IND-NPs in the Göttingen minipigs’ skin. In conclusion, we found that l-menthol enhanced the SC penetration of IND-NPs. In addition, this study suggests that the SC-passed IND-NPs are absorbed into the skin tissue by energy-dependent endocytosis (CavME, CME, and/or MP pathways) on the epidermis under the SC, resulting in an enhancement in transdermal penetration of IND-NPs. These findings provide significant information for the design of nanomedicines in transdermal formulations.

Drug-Eluting Medical Textiles: From Fiber Production and Textile Fabrication to Drug Loading and Delivery

Drug-eluting medical textiles have recently gained great attention to be used in different applications due to their cost effectiveness and unique physical and chemical properties. Using various fiber production and textile fabrication technologies, fibrous constructs with the required properties for the target drug delivery systems can be designed and fabricated. This review summarizes the current advances in the fabrication of drug-eluting medical textiles. Different fiber production methods such as melt-, wet-, and electro-spinning, and textile fabrication techniques such as knitting and weaving are explained. Moreover, various loading processes of bioactive agents to obtain drug-loaded fibrous structures with required physicochemical and morphological properties, drug delivery mechanisms, and drug release kinetics are discussed. Finally, the current applications of drug-eluting fibrous systems in wound care, tissue engineering, and transdermal drug delivery are highlighted.

Inverse Mechanistic Modeling of Transdermal Drug Delivery for Fast Identification of Optimal Model Parameters

Transdermal drug delivery systems are a key technology to administer drugs with a high first-pass effect in a non-invasive and controlled way. Physics-based modeling and simulation are on their way to become a cornerstone in the engineering of these healthcare devices since it provides a unique complementarity to experimental data and additional insights. Simulations enable to virtually probe the drug transport inside the skin at each point in time and space. However, the tedious experimental or numerical determination of material properties currently forms a bottleneck in the modeling workflow. We show that multiparameter inverse modeling to determine the drug diffusion and partition coefficients is a fast and reliable alternative. We demonstrate this strategy for transdermal delivery of fentanyl. We found that inverse modeling reduced the normalized root mean square deviation of the measured drug uptake flux from 26 to 9%, when compared to the experimental measurement of all skin properties. We found that this improved agreement with experiments was only possible if the diffusion in the reservoir holding the drug was smaller than the experimentally measured diffusion coefficients suggested. For indirect inverse modeling, which systematically explores the entire parametric space, 30,000 simulations were required. By relying on direct inverse modeling, we reduced the number of simulations to be performed to only 300, so a factor 100 difference. The modeling approach's added value is that it can be calibrated once in-silico for all model parameters simultaneously by solely relying on a single measurement of the drug uptake flux evolution over time. We showed that this calibrated model could accurately be used to simulate transdermal patches with other drug doses. We showed that inverse modeling is a fast way to build up an accurate mechanistic model for drug delivery. This strategy opens the door to clinically ready therapy that is tailored to patients.

Emerging Functional Biomaterials as Medical Patches

Medical patches have been widely explored and applied in various medical fields, especially in wound healing, tissue engineering, and other biomedical areas. Benefiting from emerging biomaterials and advanced manufacturing technologies, great achievements have been made on medical patches to evolve them into a multifunctional medical device for diverse health-care purposes, thus attracting extensive attention and research interest. Here, we provide up-to-date research concerning emerging functional biomaterials as medical patches. An overview of the various approaches to construct patches with micro- and nanoarchitecture is presented and summarized. We then focus on the applications, especially the biomedical applications, of the medical patches, including wound healing, drug delivery, and real-time health monitoring. The challenges and prospects for the future development of the medical patches are also discussed.

Transdermal System Based on Solid Cilostazol Nanoparticles Attenuates Ischemia/Reperfusion-Induced Brain Injury in Mice

Cilostazol (CIL) exerted a protective effect by promoting blood-brain barrier integrity as well as improving the status of neurological dysfunctions following cerebral ischemia/reperfusion (I/R) injury. We attempted to design a 0.5% CIL carbopol gel using solid nanoparticles (CIL-Ngel), and then investigated the relationships between energy-dependent endocytosis and the skin penetration of CIL-Ngel in this study. In addition, we evaluated whether the CIL-Ngel attenuated I/R-induced brain injury in a middle cerebral artery occlusion (MCAO)/reperfusion model mouse. The particle size of CIL was decreased using a bead mill, and the CIL particles (14.9 × 10¹⁴ particles/0.3 g) in the CIL-Ngel were approximately 50-180 nm. The release of CIL in the CIL-Ngel was higher than that in gel containing CIL powder (CIL-Mgel), and the CIL particles were released from the CIL-Ngel as nanoparticles. In addition, the percutaneous absorption of CIL from the CIL-Ngel was higher in comparison with that from CIL-Mgel, and clathrin-dependent endocytosis and caveolae-dependent endocytosis were related to the enhanced skin penetration of CIL-NPs. In the traditional (oral administration of CIL powder, 3 mg/kg) and transdermal administration (CIL-Ngel, 0.3 g) for 3 days (once a day), the area under the plasma CIL concentration-time curves (AUC) was similar, although the CIL supplied to the blood by the CIL-Ngel was more sustained than that via oral administration of CIL powder. Furthermore, the CIL-Ngel attenuated the ischemic stroke. In conclusion, we designed a gel using solid CIL-NPs, and we showed that the sustained release of CIL by CIL-Ngel provided an effective treatment for ischemic stroke in MCAO/reperfusion model mice. These findings induce the possibilities of developing novel applications of CIL solid nanoparticles.

Engineering Hydrogel Adhesion for Biomedical Applications via Chemical Design of the Junction

Hydrogel adhesion inherently relies on engineering the contact surface at soft and hydrated interfaces. Upon contact, adhesion normally occurs through the formation of chemical or physical interactions between the disparate surfaces. The ability to form these adhesion junctions is challenging for hydrogels as the interfaces are wet and deformable and often contain low densities of functional groups. In this Review, we link the design of the binding chemistries or adhesion junctions, whether covalent, dynamic covalent, supramolecular, or physical, to the emergent adhesive properties of soft and hydrated interfaces. Wet adhesion is useful for bonding to or between tissues and implants for a range of biomedical applications. We highlight several recent and emerging adhesive hydrogels for use in biomedicine in the context of efficient junction design. The main focus is on engineering hydrogel adhesion through molecular design of the junctions to tailor the adhesion strength, reversibility, stability, and response to environmental stimuli.

Combinatorial microneedle patch with tunable release kinetics and dual fast-deep/sustained release capabilities

Transdermal microneedle (MN) drug delivery patches, comprising water-soluble polymers, have played an essential role in diverse biomedical applications, but with limited development towards fast deep release or sustained delivery applications. The effectiveness of such MN delivery patches strongly depends on the materials from which they are constructed. Herein, we present a dual-action combinatorial programmable MN patch, comprising of fast and sustained-release MN zones, with tunable release kinetics towards delivering a wide range of therapeutics over different timeframes in single application. We demonstrate the fine tuning of MN materials; the patches can be tailored to deliver a first payload faster and deeper within minutes, while simultaneously delivering a second payload over long times ranging from weeks to months. The active and rapid burst release relies on embedding biodegradable Mg microparticle 'engines' in dissolvable MNs while the sustained release is attributed to biocompatible polymers that allow prolonged release in a controllable tunable manner. In addition, the patches are characterized and optimized for their design, materials and mechanical properties. These studies indicate that such programmable dual-action versatile MN platform is expected to improve therapeutic efficacy and patient compliance, achieving powerful benefits by single patch application at low manufacturing cost.

Not only in silico drug discovery: Molecular modeling towards in silico drug delivery formulations

The use of methods at molecular scale for the discovery of new potential active ligands, as well as previously unknown binding sites for target proteins, is now an established reality. Literature offers many successful stories of active compounds developed starting from insights obtained in silico and approved by Food and Drug Administration (FDA). One of the most famous examples is raltegravir, a HIV integrase inhibitor, which was developed after the discovery of a previously unknown transient binding area thanks to molecular dynamics simulations. Molecular simulations have the potential to also improve the design and engineering of drug delivery devices, which are still largely based on fundamental conservation equations. Although they can highlight the dominant release mechanism and quantitatively link the release rate to design parameters (size, drug loading, et cetera), their spatial resolution does not allow to fully capture how phenomena at molecular scale influence system behavior. In this scenario, the "computational microscope" offered by simulations at atomic scale can shed light on the impact of molecular interactions on crucial parameters such as release rate and the response of the drug delivery device to external stimuli, providing insights that are difficult or impossible to obtain experimentally. Moreover, the new paradigm brought by nanomedicine further underlined the importance of such computational microscope to study the interactions between nanoparticles and biological components with an unprecedented level of detail. Such knowledge is a fundamental pillar to perform device engineering and to achieve efficient and safe formulations. After a brief theoretical background, this review aims at discussing the potential of molecular simulations for the rational design of drug delivery systems.

Preparation and evaluation of functional allopurinol imprinted starch based biomaterials for transdermal drug delivery

This study focuses on the synthesis of functional allopurinol (ALP) imprinted biomaterials for a transdermal drug delivery using mung bean starch (MBS), polyvinyl alcohol (PVA), sodium benzoate (SB) as a crosslinking agent, and poloxamer (PX) as a thermo-sensitive polymer. Prepared functional biomaterials were characterized and evaluated by SEM, FT-IR analysis, and physical properties. Results of ALP recognition properties indicated that adsorbed amounts (Q) of ALP on functional ALP imprinted biomaterials were 3.8 to 4.9-fold higher than that of non-ALP imprinted biomaterial. Results of ALP release revealed that the ALP release rate for PX added biomaterials was 1.10 (36.5 °C) or 1.30 (45 °C) times faster than that at 25 °C. These results indicate that functional ALP imprinted biomaterials have thermo-sensitive properties due to the addition of PX. Results of ALP release using artificial skin indicated that ALP release was increased at a relatively steady-state rate for 3 h and that the ALP release behavior followed the non-Fickian diffusion mechanism.

Microneedle-mediated transdermal drug delivery for treating diverse skin diseases

Transdermal drug delivery is an attractive route for dermatological disease therapy because it can directly target the lesion site on the skin, reduce adverse reactions associated with systemic administration, and improve patient compliance. However, the stratum corneum, as the main skin barrier, severely limits transdermal drug penetration, with compromised bioavailability. Microneedles (MNs), which are leveraged to markedly improve the penetration of therapeutic agents by piercing the stratum corneum and creating hundreds of reversible microchannels in a minimally invasive manner, have been envisioned as a milestone for effective transdermal drug delivery, especially for superficial disease therapy. Here, the emergence of versatile MNs for the transdermal delivery of various drugs is reviewed, particularly focusing on the application of MNs for the treatment of diverse skin diseases, including superficial tumors, scars, psoriasis, herpes, acne, and alopecia. Additionally, the promises and challenges of the widespread translation of MN-mediated transdermal drug delivery in the dermatology field are summarized.

Iontophoresis-driven porous microneedle array patch for active transdermal drug delivery

A transdermal patch that combines microneedle array (MA) with iontophoresis can achieve synergistic and remarkable enhancement of drug delivery with precise electronic control. However, the development of an MA patch combined with iontophoresis that can enable in situ treatment, easy self-administration, and controllable delivery of liquid macromolecular drugs is still a challenge. Here, we presented an iontophoresis-driven porous MA patch (IDPMAP) for in situ, patient-friendly, and active delivery of charged macromolecular drugs. IDPMAP integrates porous MA with iontophoresis into a single transdermal patch, thus realizing the one-step drug administration strategy of "Penetration, Diffusion, and Iontophoresis." Moreover, a matching portable iontophoresis-driven device was developed for drug self-administration of IDPMAP. In vitro and in vivo studies showed that IDPMAP had approximately 99% skin penetration rate, negligible cytotoxicity, and good biocompatibility without skin irritation and hypersensitivity. In vivo transdermal delivery of insulin in type 1 diabetic rats demonstrated that IDPMAP could effectively deliver insulin nanovesicles and produce a robust hypoglycemic effect on the rats (maintain normal blood glucose for approximately 5.4 h), with more advanced controllability and efficiency than that achieved by pristine MA or iontophoresis. IDPMAP and its portable iontophoresis-driven device are user-friendly and thus show a promising potential for drug self-administration at home.

Nanostructured Lipid Carriers Engineered as Topical Delivery of Etodolac: Optimization and Cytotoxicity Studies

Etodolac (ETD), a nonsteroidal anti-inflammatory drug, exhibits antinflammatory, analgesic, and antipyretic activity. The main type of ETD administration is oral route, which is associated with significant systemic side effects. Nanostructured lipid carriers (NLC), a modern lipid formulation, are non-toxic, biocompatible, can improve the solubility and stability of drugs. Nanostructured lipid carriers (NLC) containing etodolac were prepared by a melt-emulsification and ultrasonication technique. Full factorial design (FFD) was applied to optimize the composition of NLC and their properties such as zeta potential, polidyspersity index, and entrapment efficiency. Formulations consisting of Capryol 90, glicerol monostearate, and Tween 20 displayed particle size below 300 nm, encapsulated drug with efficiency of approximately 87% and prolonged drug release up to 24 h. Stable formulations displayed moderately negative surface charge suggesting their limited ability to interact with skin surface but simultaneously presenting their lower risk to cause cell-membrane disruption. In fact, cytotoxicity assessment using human dermal fibroblasts and human epidermal keratinocytes revealed that etodolac-loaded NLC had no important impact on skin cells viability evaluated in vitro, which might evidence that NLC formulations are safe for dermal delivery. The studies developed were relatively fast and simple, requiring no specialized equipment method to prepare NLC as ETD carriers ensuring better solubility and prolonged drug release.

Development of Stimuli-Responsive Chitosan/ZnO NPs Transdermal Systems for Controlled Cannabidiol Delivery

One of the most common neurological diseases is epilepsy, which not only negatively affects the quality of people's life but also may lead to life-threatening situations when its symptoms such as seizures cannot be controlled medically. A very serious problem to be overcame is the untreatable form of this disease, which cannot be cured by any currently available medicines. Cannabidiol, which is a natural product obtained from Cannabis Sativa, brings a new hope to people suffering from drug-resistant epilepsy. However, the hydrophobic character of this compound significantly lowers its clinical efficiency. One of the promising methods of this substance bioactivity increase is delivery through the skin tissue. In this article, a new type of advanced transdermal systems based on chitosan and ZnO nanoparticles (NPs) has been developed according to Sustained Development principles. The chemical modification of the biopolymer confirmed by FT-IR method resulted in the preparation of the material with great swelling abilities and appropriate water vapor permeability. Obtained nanoparticles were investigated over their crystalline structure and morphology and their positive impact on drug loading capacity and cannabidiol controlled release was proved. The novel biomaterials were confirmed to have conductive properties and not be cytotoxic to L929 mouse fibroblasts.

Transdermal Delivery Systems for Biomolecules

Purpose

The present review article focuses on highlighting the main technologies used as tools that improve the delivery of transdermal biomolecules, addressing them from the point of view of research in the development of transdermal systems that use physical and chemical permeation enhancers and nanocarrier systems or a combination of them.

Results

Transdermal drug delivery systems have increased in importance since the late 1970s when their use was approved by the Food and Drug Administration (FDA). They appeared to be an alternative resource for the administration of many potent drugs. The first transdermal drug delivery system used for biomolecules was for the treatment of hormonal disorders. Biomolecules have been used primarily in many treatments for cancer and diabetes, vaccines, hormonal disorders, and contraception.

Conclusions

The latest technologies that have used such transdermal biomolecule transporters include electrical methods (physical penetration enhancers), some chemical penetration enhancers and nanocarriers. All of them allow the maintenance of the physical and chemical properties of the main proteins and peptides through these clinical treatments, allowing their efficient storage, transport, and release and ensuring the achievement of their target and better results in the treatment of many diseases.

Graphical abstract

Developing Insulin Delivery Devices with Glucose Responsiveness

Individuals with type 1 and advanced type 2 diabetes require daily insulin therapy to maintain blood glucose levels in normoglycemic ranges to prevent associated morbidity and mortality. Optimal insulin delivery should offer both precise dosing in response to real-time blood glucose levels as well as a feasible and low-burden administration route to promote long-term adherence. A series of glucose-responsive insulin delivery mechanisms and devices have been reported to increase patient compliance while mitigating the risk of hypoglycemia. This review discusses currently available insulin delivery devices, overviews recent developments towards the generation of glucose-responsive delivery systems, and provides commentary on the opportunities and barriers ahead regarding the integration and translation of current glucose-responsive insulin delivery designs.

Apremilast Microemulsion as Topical Therapy for Local Inflammation: Design, Characterization and Efficacy Evaluation

Apremilast (APR) is a selective phosphodiesterase 4 inhibitor administered orally in the treatment of moderate-to-severe plaque psoriasis and active psoriatic arthritis. The low solubility and permeability of this drug hinder its dermal administration. The purpose of this study was to design and characterize an apremilast-loaded microemulsion (APR-ME) as topical therapy for local skin inflammation. Its composition was determined using pseudo-ternary diagrams. Physical, chemical and biopharmaceutical characterization were performed. Stability of this formulation was studied for 90 days. Tolerability of APR-ME was evaluated in healthy volunteers while its anti-inflammatory potential was studied using in vitro and in vivo models. A homogeneous formulation with Newtonian behavior and droplets of nanometric size and spherical shape was obtained. APR-ME released the incorporated drug following a first-order kinetic and facilitated drug retention into the skin, ensuring a local effect. Anti-inflammatory potential was observed for its ability to decrease the production of IL-6 and IL-8 in the in vitro model. This effect was confirmed in the in vivo model histologically by reduction in infiltration of inflammatory cells and immunologically by decrease of inflammatory cytokines IL-8, IL-17A and TNFα. Consequently, these results suggest that this formulation could be used as an attractive topical treatment for skin inflammation.

Sustained Acoustic Medicine Combined with A Diclofenac Ultrasound Coupling Patch for the Rapid Symptomatic Relief of Knee Osteoarthritis: Multi-Site Clinical Efficacy Study

BACKGROUND

Sustained Acoustic Medicine (SAM) is an emerging, non-invasive, non-narcotic, home-use ultrasound therapy for the daily treatment of joint pain. The aim of this multi-site clinical study was to examine the efficacy of long-duration continuous ultrasound combined with a 1% diclofenac ultrasound gel patch in treating pain and improving function in patients with knee osteoarthritis.

METHODS

The Consolidated Standards of Reporting Trials (CONSORT) were followed. Thirty-two (32) patients (18-males, 14-females) 54 years of average age with moderate to severe knee pain and radiographically confirmed knee osteoarthritis (Kellgren-Lawrence (KL) grade II/III) were enrolled for treatment with the SAM device and diclofenac patch applied daily to the treated knee. SAM ultrasound (3 MHz, 0.132 W/cm2, 1.3 W) and 6 grams of 1% diclofenac were applied with a wearable device for 4 hours daily for 1 week, delivering 18,720 Joules of ultrasound energy per treatment. The primary outcome was the daily change in pain intensity using a numeric rating scale (NRS 0-10), which was assessed prior to intervention (baseline, day 1), before and after each daily treatment, and after 1 week of daily treatment (day 7). Rapid responders were classified as those patients exhibiting greater than a 1-point reduction in pain following the first treatment. Change in Western Ontario McMaster Osteoarthritis Questionnaire (WOMAC) score from baseline to day 7 was the secondary functional outcome measure. Additionally, a series of daily usability and user experience questions related to devising ease of use, functionality, safety, and effectiveness, were collected. Data were analyzed using t-tests and repeated measure ANOVAs.

RESULTS

The study had a 94% retention rate, and there were no adverse events or study-related complaints across 224 unique treatment sessions. Rapid responders included 75% of the study population. Patients exhibited a significant mean NRS pain reduction over the 7-day study of 2.06-points (50%) for all subjects (n=32, p<0.001) and 2.96-points (70%) for rapid responders (n=24, p<0.001). The WOMAC functional score significantly improved by 351 points for all subjects (n=32, p<0.001), and 510 points for rapid responders (n=24, p<0.001). Over 95% of patients found the device safe, effective and easy to use, and would continue treatment for their knee OA symptoms.

CONCLUSION

Sustained Acoustic Medicine combined with 1% topical diclofenac rapidly reduced pain and improved function in patients with moderate to severe osteoarthritis-related knee pain. The clinical findings suggest that this treatment approach may be used as a conservative, non-invasive treatment option for patients with knee osteoarthritis. Additional research is warranted on non-weight bearing joints of the musculoskeletal system as well as different topical drugs that could benefit from improved localized delivery.Clinical Trial Registry Number: (NCT04391842).

Poly(dimethylsiloxane): A Sustainable Human Skin Alternative for Transdermal Drug Delivery Prediction

Despite the advantages of transdermal drug delivery (TDD), which makes it a fast-growing area of research in pharmaceutics, numerous challenges affect their development, which limits exploring the full potential of this alternate drug delivery route. In trying to address one of these problems, it is strongly believed that the need for a sustainable skin alternative is paramount. Efforts made in an attempt to provide a sustainable alternative to employing skin in pharmaceutical analysis, by better utilising a polymer membrane, namely poly(dimethylsiloxane), also known as PDMS are discussed. Several combined properties of this polymer, which includes its relative stability in comparison with human skin, make it a good candidate for the replacement of skin. Modifications undertaken to this polymer membrane (to create an enhanced skin mimic for permeation analysis) are discussed and reviewed in this paper, including the improved ability to predict permeability for both hydrophobic and hydrophilic drugs. Optimisations related to studying TDD including limitations encountered are also documented and reviewed. It is hoped that such developments in this field will ultimately lead to researchers replacing skin with optimised polymer-based alternatives to predict transdermal drug delivery.

Transdermal Delivery of Gold Nanoparticles by a Soybean Oil-Based Oleogel under Iontophoresis

Developing a facile mechanism for transporting nanoparticles across the whole skin by overcoming the stratum corneum is a challenging task. Herein, a stimuli-responsive and noninvasive transport of gold nanoparticles (AuNPs) has been reported through the fabrication of AuNP-incorporated soybean oil-based oleogels (AuG) using stearic acid as a gelator. A series of AuG was formulated by incorporating different proportions of AuNPs and a fixed amount of ciprofloxacin hydrochloride (drug) to establish that the composition with the highest concentration of AuNP (d-AuG4) was associated with the best iontophoretic response, validated via the corresponding in vitro drug release under AC field-induced iontophoresis. The sample d-AuG4 exhibited both drug and AuNP permeation across the whole pig ear skin thickness within as early as 1 h under the iontophoresis condition. With relevant control experiments, it was shown that the transport of AuNPs through the stratum corneum tissue and across the whole skin was possible upon the simultaneous fulfillment of two conditions: the presence of a skin permeation enhancer (stearic acid) within the oleogel and iontophoresis. While the literature reported that the permeation time for any free inorganic nanoparticle through the full-skin thickness varied within a few days, the permeation enhancement technique developed here reduced the corresponding delivery time for the AuNPs to a few hours. The extent of AuNP permeation that occurred in the microgram (per cm^-2) scale was found to be affected by the duration of iontophoresis, suggesting that AuNPs' rapid transdermal entry can be simultaneously triggered and modulated by iontophoretic conditions.

Rapidly dissolving microneedles for the delivery of cubosome-like liquid crystalline nanoparticles with sustained release of rapamycin

In this study, we developed a system for the transdermal delivery and controlled release of the hydrophobic immunosuppressive drug rapamycin, foreseeing an application in psoriasis treatment. To do so, rapamycin was encapsulated in phytantriol-based cubosome-like liquid crystalline nanoparticles stabilized with pluronic F127. The final mass percent composition of the lipid nanoparticles was 0.25% phytantriol, 0.1% pluronic F127, 4.75% ethanol and 94.9% water. These particles showed a rapamycin encapsulation efficiency above 95% and a sustained in vitrodrug release profile throughout 14 days. Subsequently the rapamycin-carrying particles were incorporated into rapidly dissolving microneedle patches composed of a polymeric matrix of poly(vinylpyrrolidone) and poly(vinyl alcohol). Confocal microscopy allowed to infer the preferential distribution of the cubosome-like particles at the tip and baseplate of the microneedles. The fabricated microneedles showed successful piercing and deposition of the loaded cubosome-like particles on a skin-mimicking agarose gel. Finally, the rapamycin-loaded cubosome-like particles showed antiproliferative activity in natural killer cells in vitro. The results here presented show the potential of the developed system to deliver cubosome-like particles into the skin and promote the sustained release of rapamycin in the context of immunomodulation.

Predicting Transdermal Fentanyl Delivery Using Mechanistic Simulations for Tailored Therapy

Transdermal drug delivery is a key technology for administering drugs. However, most devices are “one-size-fits-all”, even though drug diffusion through the skin varies significantly from person-to-person. For next-generation devices, personalization for optimal drug release would benefit from an augmented insight into the drug release and percutaneous uptake kinetics. Our objective was to quantify the changes in transdermal fentanyl uptake with regards to the patient’s age and the anatomical location where the patch was placed. We also explored to which extent the drug flux from the patch could be altered by miniaturizing the contact surface area of the patch reservoir with the skin. To this end, we used validated mechanistic modeling of fentanyl diffusion, storage, and partitioning in the epidermis to quantify drug release from the patch and the uptake within the skin. A superior spatiotemporal resolution compared to experimental methods enabled in-silico identification of peak concentrations and fluxes, and the amount of stored drug and bioavailability. The patients’ drug uptake showed a 36% difference between different anatomical locations after 72 h, but there was a strong interpatient variability. With aging, the drug uptake from the transdermal patch became slower and less potent. A 70-year-old patient received 26% less drug over the 72-h application period, compared to an 18-year-old patient. Additionally, a novel concept of using micron-sized drug reservoirs was explored in silico. These reservoirs induced a much higher local flux (µg cm^-2 h^-1) than conventional patches. Up to a 200-fold increase in the drug flux was obtained from these small reservoirs. This effect was mainly caused by transverse diffusion in the stratum corneum, which is not relevant for much larger conventional patches. These micron-sized drug reservoirs open new ways to individualize reservoir design and thus transdermal therapy. Such computer-aided engineering tools also have great potential for in-silico design and precise control of drug delivery systems. Here, the validated mechanistic models can serve as a key building block for developing digital twins for transdermal drug delivery systems.

Current trends in polymer microneedle for transdermal drug delivery

Transdermal drug delivery using microneedles is increasingly gaining interest due to the issues associated with oral drug delivery routes. Gastrointestinal route exposes the drug to acid and enzymes present in the stomach, leading to denaturation of the compound and resulting in poor bioavailability. Microneedle transdermal drug delivery addresses the problems linked to oral delivery and to relieves the discomfort of patients associated with injections to increase patient compliance. Microneedles can be broadly classified into five types: solid microneedles, coated microneedles, dissolving microneedles, hollow microneedles, and hydrogel-forming microneedles. The materials used for the preparation of microneedles dictate the different applications and features present in the microneedle. Polymeric microneedle arrays present an improved method for transdermal administration of drugs as they penetrate the skin stratum corneum barrier with minimal invasiveness. The review summarizes the importance of polymeric microneedle and discussed some of the most important therapeutic drugs in research, mainly protein drugs, vaccines and small molecule drugs in regenerative medicine.

Progress and perspective of microneedle system for anti-cancer drug delivery

Transdermal drug delivery exhibited encouraging prospects, especially through superficial drug administration routes. However, only a few limited lipophilic drug molecules could cross the skin barrier, those are with low molecular weight and rational Log P value. Microneedles (MNs) can overcome these limitations to deliver numerous drugs into the dermal layer by piercing the outermost skin layer of the body. In the case of superficial cancer treatments, topical drug administration faces severely low transfer efficiency, and systemic treatments are always associated with side effects and premature drug degradation. MN-based systems have achieved excellent technical capabilities and been tested for pre-clinical chemotherapy, photothermal therapy, photodynamic therapy, and immunotherapy. In this review, we will focus on the features, progress, and opportunities of MNs in the anticancer drug delivery system. Then, we will discuss the strategies and advantages in these works and summarize challenges, perspectives, and translational potential for future applications.

Advances in drug delivery technology for the treatment of glioblastoma multiforme

Glioblastoma multiforme (GBM) is a particularly aggressive and malignant type of brain tumor, notorious for its high recurrence rate and low survival rate. The treatment of GBM is challenging mainly because several issues associated with the GBM microenvironment have not yet been resolved. These obstacles originate from a variety of factors such as genetics, anatomy, and cytology, all of which collectively hinder the treatment of GBM. Recent advances in materials and device engineering have presented new perspectives with regard to unconventional drug administration methods for GBM treatment. Such novel drug delivery approaches, based on the clear understanding of the intrinsic properties of GBM, have shown promise in overcoming some of the obstacles. In this review, we first recapitulate the first-line therapy and clinical challenges in the current treatment of GBM. Afterwards, we introduce the latest technological advances in drug delivery strategies to improve the efficiency for GBM treatment, mainly focusing on materials and devices. We describe such efforts by classifying them into two categories, systemic and local drug delivery. Finally, we discuss unmet challenges and prospects for the clinical translation of these drug delivery technologies.