Influences of Chemical Properties, Soil Properties, and Solution pH on Soil-Water Partitioning Coefficients of Per- and Polyfluoroalkyl Substances (PFASs)

Effect of pH, surface charge and soil properties on the solid-solution partitioning of perfluoroalkyl substances (PFASs) in a wide range of temperate soils

The pH-dependent soil-water partitioning of six perfluoroalkyl substances (PFASs) of environmental concern (PFOA, PFDA, PFUnDA, PFHxS, PFOS and FOSA), was investigated for 11 temperate mineral soils and related to soil properties such as organic carbon content (0.2-3%), concentrations of Fe and Al (hydr)oxides, and texture. PFAS sorption was positively related to the perfluorocarbon chain length of the molecule, and inversely related to solution pH for all substances. The negative slope between log K_d and pH became steeper with increasing perfluorocarbon chain length of the PFAS (r² = 0.75, p ≤ 0.05). Organic carbon (OC) alone was a poor predictor of the partitioning for all PFASs, except for FOSA (r² = 0.71), and the OC-normalized PFAS partitioning, as derived from organic soil materials, underestimated PFAS sorption to the soils. Multiple linear regression suggested sorption contributions (p ≤ 0.05) from OC for perfluorooctane sulfonate (PFOS) and FOSA, and Fe/Al (hydr)oxides for PFOS, FOSA, and perfluorodecanoate (PFDA). FOSA was the only substance under study for which there was a statistically significant correlation between its binding and soil texture (silt + clay). To predict PFAS sorption, the surface net charge of the soil organic matter fraction of all soils was calculated using the Stockholm Humic Model. When calibrated against charge-dependent PFAS sorption to a peat (Oe) material, the derived model significantly underestimated the measured K_d values for 10 out of 11 soils. To conclude, additional sorbents, possibly including silicate minerals, contribute to the binding of PFASs in soil. More research is needed to develop geochemical models that can accurately predict PFAS sorption in soils.

Bioaccumulation of per- and polyfluoroalkyl substances by freshwater benthic macroinvertebrates: Impact of species and sediment organic carbon content

Per- and polyfluoroalkyl substances (PFAS) in aquatic environments have caused global concern due to their persistence, toxicity, and potential bioaccumulation of some compounds. As an important compartment of the aquatic ecosystem, sediment properties impact PFAS partitioning between aqueous and solid phases, but little is known about the influence of sediment organic carbon content on PFAS bioaccumulation in benthic organisms. In this study, three freshwater benthic macroinvertebrates - worms (Lumbriculus variegatus), mussels (Elliptio complanata) and snails (Physella acuta) - were exposed for 28 days to PFAS spiked synthetic sediment equilibrated with a synthetic surface water. Using microcosms, sediment organic carbon content - 2%, 5% and 8% - was manipulated to assess its impact on PFAS bioaccumulation. Worms were found to have substantially greater PFAS bioaccumulation compared to mussels and snails. The bioaccumulation factors (BAFs) and biota sediment accumulation factors (BSAFs) in worms were both one to two magnitudes higher than in mussels and snails, likely due to different habitat-specific uptake pathways and elimination capacities among species. In these experiments, increasing sediment organic carbon content decreased the bioaccumulation of PFAS to benthic macroinvertebrates. In worms, sediment organic carbon content was hypothesized to impact PFAS bioaccumulation by affecting PFAS partitioning and sediment ingestion rate. Notably, the BSAF values of 8:2 fluorotelomer sulfonic acid (FTS) were the largest among 14 PFAS for all species, suggesting that the benthic macroinvertebrates probably have different metabolic mechanisms for fluorotelomer sulfonic acids compared to fish evaluated in published literature. Understanding the impact of species and sediment organic carbon on PFAS bioaccumulation is key to developing environmental quality guidelines and evaluating potential ecological risks to higher trophic level species.

Effect of geochemical conditions on PFAS release from AFFF-impacted saturated soil columns

Per- and polyfluoroalkyl substances (PFASs) are frequently found at high concentrations in the subsurface of aqueous film forming foam (AFFF)-impacted sites. Geochemical parameters affect the release of PFASs from source area soils into groundwater but have not been extensively studied for soils that have been historically impacted with AFFF. This study investigated the effects of pH and salt concentrations on release of anionic and zwitterionic PFASs from AFFF-impacted soils in flow-through saturated columns. High pH (10) columns with elevated sodium concentrations had higher cumulative masses eluted of several PFASs compared to pH 3 and pH 7 columns with lower sodium concentrations, likely caused by changes to soil organic matter surface charge. Four PFASs (e.g. 4:2 fluorotelomer sulfonate, perfluorobutane sulfonamido acetic acid) eluted significantly earlier in both pH 3 and pH 10/high NaCl columns compared to pH 7 columns. The results of this study suggest that shifts in pH for soils located at AFFF-impacted sites - particularly raising the pH - may mobilize sorbed PFASs, specifically longer-chain and zwitterionic compounds that are typically strongly sorbed to soil.

Uptake of Ultrashort Chain, Emerging, and Legacy Per- and Polyfluoroalkyl Substances (PFAS) in Edible Mushrooms (Agaricus spp.) Grown in a Polluted Substrate

Uptake of 19 per- and polyfluoroalkyl substances (PFAS), including C3-C14 perfluoroalkyl carboxylic acids (PFCAs), C4, C6, and C8 perfluoroalkyl sulfonates (PFSAs), and four emerging PFAS, was investigated in two mushroom species (Agaricus bisporus and Agaricus subrufescens) cultivated in a biogas digestate-based substrate. Accumulation of PFAS in mushrooms was low and strongly chain-length dependent. Among the different PFCAs, bioaccumulation factors (log BAFs) decreased from a maximum of -0.3 for perfluoropropanoic acid (PFPrA; C3) to a minimum of -3.1 for perfluoroheptanoate (PFHpA; C7), with only minor changes from PFHpA to perfluorotridecanoate (PFTriDA; C13). For PFSAs, log BAFs decreased from perfluorobutane sulfonate (PFBS; -2.2) to perfluorooctane sulfonate (PFOS; -3.1) while mushroom uptake was not observed for the alternatives 3H-perfluoro-3-[(3-methoxy-propoxy)propanoic acid] (ADONA) and two chlorinated polyfluoro ether sulfonates. To the best of our knowledge, this is the first investigation of the uptake of emerging and ultra-short chain PFAS in mushrooms, and generally the results indicate very low accumulation of PFAS.

Warming Affects Bioconcentration and Bioaccumulation of Per- and Polyfluoroalkyl Substances by Pelagic and Benthic Organisms in a Water-Sediment System

Warming and exposure to emerging global pollutants, such as per- and polyfluoroalkyl substances (PFAS), are significant stressors in the aquatic ecosystem. However, little is known about the warming effect on the bioaccumulation of PFAS in aquatic organisms. In this study, the pelagic organisms Daphnia magna and zebrafish, and the benthic organism Chironomus plumosus were exposed to 13 PFAS in a sediment-water system with a known amount of each PFAS at different temperatures (16, 20, and 24 °C). The results showed that the steady-state body burden (C_b-ss) of PFAS in pelagic organisms increased with increasing temperatures, mainly attributed to increased water concentrations. The uptake rate constant (k_u) and elimination rate constant (k_e) in pelagic organisms increased with increasing temperature. In contrast, warming did not significantly change or even mitigate C_b-ss of PFAS in the benthic organism Chironomus plumosus, except for PFPeA and PFHpA, which was consistent with declined sediment concentrations. The mitigation could be explained by the decreased bioaccumulation factor due to a more significant percent increase in k_e than k_u, especially for long-chain PFAS. This study suggests that the warming effect on the PFAS concentration varies among different media, which should be considered for their ecological risk assessment under climate change.

The efficacy of soil washing for the remediation of per- and poly-fluoroalkyl substances (PFASs) in the field

This paper aims to describe the performance of a soil washing plant (SWP) for remediating a per- and poly-fluoroalkyl substances (PFASs)-contaminated soil with a high clay content (61%). The SWP used both physical and chemical processes; fractionation of the soil particles by size and partitioning of PFASs into the aqueous phase to remove PFASs from the soil. Contaminated water was treated in series with granulated activated carbon (GAC) and ion-exchange resin and reused within the SWP. Approximately 2200 t (dry weight) of PFAS-contaminated soil was treated in 25 batches of 90 t each, with a throughput of approximately 11 t soil/hr. Efficiency of the SWP was measured by observed decreases in total and leachable concentrations of PFASs in the soil. Average removal efficiencies (RE) were up to 97.1% for perfluorocarboxylic acids and 94.9% for perfluorosulfonic acids. REs varied among different PFASs depending on their chemistry (functional head group, carbon chain length) and were independent of the total PFAS concentrations in each soil batch. Mass balance analysis found approximately 90% of the PFAS mass in the soil was transferred to the wash solution and > 99.9% of the PFAS mass in the wash solution was transferred onto the GAC without any breakthrough.

Recent advances in the remediation of perfluoroalkylated and polyfluoroalkylated contaminated sites

Per- and polyfluoroalkyl substances (PFASs) are compounds used since 1940 in various formulations in the industrial and consumer sectors due to their high chemical and thermal stability. In recent years, PFASs have caused global concern due to their presence in different water and soil matrices, which threatens the environment and human health. These compounds have been reported to be linked to the development of serious human diseases, including but not limited to cancer. For this reason, PFASs have been considered as persistent organic compounds (COPs) and contaminants of emerging concern (CECs). Therefore, this work aims to present the advances in remediation of PFASs-contaminated soil and water by addressing the current literature. The performance and characteristics of each technique were addressed deeply in this work. The reviewed literature found that PFASs elimination studies in soil and water were carried out at a laboratory and pilot-scale in some cases. It was found that ball milling, chemical oxidation and thermal desorption are the most efficient techniques for the removal of PFASs in soils, however, phyto-microbial remediation is under study, which claims to be a promising technique. For the remediation of PFASs-contaminated water, the processes of electrocoagulation, membrane filtration, ozofractionation, catalysis, oxidation reactions - reduction, thermolysis and destructive treatments with plasma have presented the best results. It is noteworthy that hybrid treatments have also proved to be efficient techniques in the removal of these contaminants from soil and water matrices. Therefore, the improvisation and implication of existing techniques on a field-scale are greatly warranted to corroborate the yields obtained on a pilot- and laboratory-scale.

Different Sources, Fractionation, and Migration of Legacy and Novel Per- and Polyfluoroalkyl Substances between Greenhouse and Open-Field Soils

Perfluoroalkyl substances (PFASs) are widely present in agricultural soils, but their sources and fate in greenhouse soils remain unclear. In this study, the sources, fractionation, and migration of PFASs were compared in the greenhouse and open-field soils of the Fen-Wei Plain, China. The total concentrations of PFASs (Σ₁₇PFAS) were comparable in the greenhouse and open-field soils but with different profiles. Detrended correspondence and correlation analyses indicated that dry deposition was an important source of PFASs in the open-field soils, whereas surface water had a notable contribution to the greenhouse soils due to more frequent irrigation. The PFASs in the soils were mainly present in water-soluble fraction (F1). The F1 proportions of short-chain and long-chain PFASs were negatively correlated with the anion exchange capacity (AEC) and organic carbon content (f_oc) in soil, respectively, with that of short-chain PFASs being higher than long-chain ones. The AEC was significantly higher while f_oc was lower in the greenhouse soil than the open-field soil, leading to lower proportions of F1 for short-chain PFASs while higher for long-chain ones in the greenhouse soil. Frequent irrigation and elevated temperatures promoted the migration of PFASs in greenhouse soil; thus, the Σ₁₇PFAS and F1 exhibited an increasing trend with soil depth.

Trace Analysis Method Based on UPLC-MS/MS for the Determination of (C2-C18) Per-and Polyfluoroalkyl Substances and Its Application to Tap Water and Bottled Water

As the usage of long-chain perfluoroalkyl and polyfluoroalkyl substances (PFASs) may be gradually restricted, short-chain and even ultra-short-chain PFASs have been widely produced and used, which has put forward new requirements for the simultaneous analysis of the above substances. Using solid phase extraction two-fraction elution and ultra-performance liquid chromatography tandem mass spectrometry (UPLC-MS/MS), an experimental method was established for the simultaneous analysis of ultrashort-chain, short-chain, and long-chain PFASs and the precursor perfluorohexanesulfonamide (FHxSA) in low-concentration water, such as tap water and bottled water. By optimizing the volume of methanol in the first-fraction elution, the concentration of ammonia in the second-fraction elution, and the concentration of ammonium acetate in the mobile phase, the high recovery and low detection limit (0.01-3 ng/L) were obtained. In addition, this method was used to measure nine tap water samples and six bottled water samples for validation, and the results showed that the concentration of PFASs in bottled water was lower than that in tap water. This study first reported the trifluoroacetic acid concentration in bottled water (6.61 ± 9.60 ng/L), which was lower than that in tap water (1712 ± 174 ng/L). The main substances in tap water and bottled water are both ultrashort-chain PFASs (C2-C3), accounting for more than 50%. There are few reports on the simultaneous analysis of ultrashort-chain, short-chain, and long-chain PFASs (C2-C18) and the precursor FHxSA in low-concentration water samples, and the new method can be further developed for different environmental media.

Per- and Poly-Fluoroalkyl Substances in Runoff and Leaching from AFFF-Contaminated Soils: a Rainfall Simulation Study

The mobilization and transport of per- and poly-fluoroalkyl substances (PFASs) via surface runoff (runoff) from aqueous film-forming foam (AFFF)-contaminated soils during rainfall, flooding, or irrigation has not been thoroughly evaluated, and the effectiveness of carbonaceous sorbents in limiting PFASs in runoff is similarly unquantified. Here, laboratory-scale rainfall simulations evaluate PFAS losses in runoff and in leaching to groundwater (leachate) from AFFF-contaminated soils varying in texture, PFAS composition and concentration, and remediation treatment. Leaching dominated PFAS losses in soils with a concentration of ∑PFAS = 0.2-2 mg/kg. However, with higher soil PFAS concentrations (∑PFAS = 31 mg/kg), leachate volumes were negligible and runoff dominated losses. The concentration and variety of PFASs were far greater in leachates regardless of the initial concentrations in soil. Losses of PFASs were dependent on the C-chain length for leachates and more on the initial concentration in soil for runoff. Suspended materials did not meaningfully contribute to runoff losses. While concentrations of most PFASs declined significantly after the first rainfall event, desorption and transport in both runoff and leachates persisted over several rainfall events. Finally, results showed that sorption to AC mostly occurred during, not prior to, rainfall events and that 1% w/w AC substantially reduced losses in runoff and leachates from all soils.

Significant riverine inputs of typical plastic additives-phthalate esters from the Pearl River Delta to the northern South China Sea

Phthalate esters (PAEs) are representative additives used extensively in plastics. In this study, 15 PAEs were investigated at the eight riverine outlets of the Pearl River Delta (PRD). The total concentrations of Σ₁₅PAEs, including both the dissolved and particulate phases, ranged from 562 to 1460 ng/L and 679 ng/L-2830 ng/L in the surface and bottom layers, respectively. Dibutyl phthalate (DBP) and di(2-ethylhexyl) phthalate (DEHP) dominated in the dissolved and suspended particulate matter (SPM) phases, respectively, accounting for >50 % and > 80 % of Σ₁₅PAEs. Riverine input of wastewater from the PRD was possibly the primary source of the contamination. Higher levels of PAEs occurred at the eastern outlets than at the western ones. The dissolved and particulate PAEs varied seasonally, with significantly higher concentrations observed in the dry season than in the wet season. However, no significant differences of PAE levels in both phases were observed among low, medium, and high tides. The partitioning results demonstrated that SPM is important in the transportation of pollutants in estuaries, where more hydrophobic DEHP was predominantly transported by the SPM phase, while those more hydrophilic ones were regularly transported by the dissolved phase. The total annual flux of Σ₁₅PAEs through the eight outlets to the SCS reached 1390 tons.

Biological and Chemical Transformation of the Six-Carbon Polyfluoroalkyl Substance N-Dimethyl Ammonio Propyl Perfluorohexane Sulfonamide (AmPr-FHxSA)

Sites impacted by aqueous film-forming foam (AFFF) contain co-contaminants that can stimulate biotransformation of polyfluoroalkyl substances. Here, we compare how microbial enrichments from AFFF-impacted soil amended with diethyl glycol monobutyl ether (found in AFFF), aromatic hydrocarbons (present in co-released fuels), acetate, and methane (substrates used or formed during bioremediation) impact the aerobic biotransformation of an AFFF-derived six-carbon electrochemical fluorination (ECF) precursor N-dimethyl ammonio propyl perfluorohexane sulfonamide (AmPr-FHxSA). We found that methane- and acetate-oxidizing cultures resulted in the highest yields of identifiable products (38 and 30%, respectively), including perfluorohexane sulfonamide (FHxSA) and perfluorohexane sulfonic acid (PFHxS). Using these data, we propose and detail a transformation pathway. Additionally, we examined chemical oxidation products of AmPr-FHxSA and FHxSA to provide insights on remediation strategies for AmPr-FHxSA. We demonstrate mineralization of these compounds using the sulfate radical and test their transformation during the total oxidizable precursor (TOP) assay. While perfluorohexanoic acid accounted for over 95% of the products formed, we demonstrate here for the first time two ECF-based precursors, AmPr-FHxSA and FHxSA, that produce PFHxS during the TOP assay. These findings have implications for monitoring poly- and perfluoroalkyl substances during site remediation and application of the TOP assay at sites impacted by ECF-based precursors.

Optimizing the fugacity model to select appropriate remediation pathways for perfluoroalkyl substances (PFASs) in a lake

Increased anthropogenic activities have caused contamination of perfluoroalkyl substances (PFASs) in lakes worldwide. However, how to remediate their contamination remains unclear. In this study, a heavily polluted lake, Baiyangdian Lake in China, was selected to investigate current PFASs levels in multimedia, stimulate their transport fate based upon an optimized fugacity model, and finally identify appropriate remediation pathways. From 2008-2019, the average concentrations of PFASs in the lake increased approximately 7-40 times in the environment and biota. Spatially, with continuous import of perfluorohexane sulfonate (PFHxS) and perfluorooctanoic acid (PFOA), barring fish, a noticeable north-south difference was distinguished in the PFASs composition in multimedia from the lake. Based on the optimized fugacity model simulation, the water phase was the primary transport path (~76.5%) for PFASs, with a total flux of 333 kg y^-1. Compared with bioaccumulation fluxes in submerged plants (6.2 kg y^-1), emerged plants (2.6 kg y^-1), and fish (1.1 kg y^-1), the exchange flux of PFASs between water and sediment remained high (~94 kg y^-1). Considering remediation cost, sediment cleaning is currently the most cost-effective pathway, while harvesting submerged plant could be a promising pathway in the future. This study provides a basis for remediating PFASs-polluted lakes on a global scale.

Laboratory batch representation of PFAS leaching from aged field soils: Intercomparison across new and standard approaches

Relating laboratory leaching methods to partitioning and transport of per- and poly-fluoroalkyl substances (PFAS) in field soils is challenging, making estimation of fluxes to groundwater and surface water uncertain. Existing laboratory leaching methods have limitations when assessing field leaching. For 37 aged field soils from five sites historically contaminated with PFAS over decades, we assess PFAS leaching using new and existing laboratory leaching methods to provide alternative methods better reflecting PFAS risks posed by its leaching and movement. Dominant PFAS in the soils were perfluorooctane sulfonic acid, perfluorohexane sulfonic acid, and perfluorohexanoic acid and to a lesser extent perfluorooctanoic acid. Leaching from intact soil cores (Exp 1) was taken to reflect field conditions. These were compared to two new laboratory batch tests, saturate-spin (Exp 2) and saturate-tumble-spin (Exp 3), and two standard approaches; Australian Standard Leaching Procedure (ASLP, Exp 4) and the Leaching Environmental Assessment Framework (LEAF, Exp 5). The tests varied in terms of liquid:soil ratio, tumbling time and pH of the starting solution, with LEAF-1313 conducted across seven pHs (2-12). Correlations between leachate and soil concentrations were highest for Exp 4 and Exp 5 (R² = 0.72-0.98) and lowest for Exp 3 (R² = 0.53). The PFAS mass leached as a fraction of the total increased such that: soil core leaching (27 %) < saturate-spin (30 %) < saturate-tumble-spin (65 %) ≤ LEAF-1313 (65 to 88 % at pH 5-9) < ASLP (90 %). As a fraction of individual PFAS compounds in leachate compared with soil, the shorter chain PFAS (e.g., perfluorobutanoic acid) were higher in the leachate in all tests. Across all tests, the saturate-spin batch test most closely represented intact soil core leaching and therefore potentially provides a measure more analogous of in situ soil leaching at field sites. Other methods would apply to broader applications such as landfill disposal.

Per- and polyfluoroalkyl substances (PFASs) in groundwater from a contaminated site in the North China Plain: Occurrence, source apportionment, and health risk assessment

Per-and polyfluoroalkyl substances (PFASs) are manmade chemicals that have wide industrial and commercial application. However, little research has been carried out on PFASs pollution in groundwater from a previously contaminated site. Here, we investigated 43 PFASs in a monitoring campaign from two different aquifers in the North China Plain. Our results revealed that total PFASs concentrations (∑₄₃PFASs) ranged from 0.22 to 3,776.76 ng/L, with no spatial or compositional differences. Moreover, perfluorooctanoic acid (PFOA) and perfluoroheptane sulfonate (PFHpS) were the dominant pollutants with mean concentrations of 177.33 ng/L and 51 ng/L, respectively. ∑₄₃PFAS decreased with well depth due to the adsorption of PFASs to the aquifer materials. Water temperature, total organic carbon, dissolved oxygen, and total phosphorus concentrations were correlated to the PFAS concentrations. Principal component analysis indicated that the main sources of PFASs in groundwater were untreated industrial discharge, untreated domestic wastewater, food packaging, aqueous film forming foams and metal plating, and surface runoff, which overlapped with the industries that previously existed in a nearby city. Human health risks from drinking contaminated groundwater were low to the local residents, with children aged 1-2 years being the most sensitive group. One specific site with a high PFOA concentration was of concern, as it was several orders higher than the 70 ng/L recommended by US Environmental Protection Agency health advisory. This study provided baseline data for PFASs in a previously-contaminated site, which will help in the development of effective strategies for controlling PFASs pollution in the North China Plain.

Effect of solution chemistry on the transport of short-chain and long-chain perfluoroalkyl carboxylic acids (PFCAs) in saturated porous media

Perfluorocarboxylic acids (PFCAs) are one of the most widely detected classes of PFAS in the global environment after decades of intensive use. This study investigated the impact of perfluorinated carbon chain length on the transport behavior of PFCAs by testing and modeling two short-chain (PFPeA and PFHxA) and two long-chain PFCAs (PFOA and PFDA) in laboratory water-saturated columns. Moreover, their transport behavior was examined under different solution chemistry conditions, including pH, ionic strength, and cationic type. The experimental and simulation results indicated that the chain length had a limited impact on transport behaviors of PFPeA, PFHxA, and PFOA under various pH and ionic strengths, evidenced by their tracer-like breakthrough curves. In contrast, the mobility of PFDA was significantly affected by pH and ionic strengths. Additionally, the transport of all four PFCAs was inhabited in the presence of the divalent cation Ca²⁺. This study could help predict migration behavior and assess the potential risk of PFCAs in the subsurface system.

Pilot study comparison of regenerable and emerging single-use anion exchange resins for treatment of groundwater contaminated by per- and polyfluoroalkyl substances (PFASs)

This study reports the results of an 8-month pilot study comparing both regenerable and emerging single-use anion exchange resins (AERs) for treatment of per- and polyfluoroalkyl substances (PFASs) at a source zone impacted by historical use of aqueous film-forming foam (AFFF). Two regenerable (Purolite A860 and A520E) and three single-use (Purolite PFA694E, Calgon CalRes 2301, and Dowex PSR2+) AERs were tested in parallel, collecting effluent samples after treatment for 30-sec and 2-min total empty bed contact time (EBCT). Results demonstrate that single-use AERs significantly outperform regenerable resins, particularly for treatment of long-chain perfluoroalkyl carboxylic acids (PFCAs) and perfluoroalkyl sulfonic acids (PFSAs). No detectable concentrations of ≥C7 PFCAs or PFSAs were observed within 150,000 bed volumes (BVs) after treatment with the single-use resins (2-min EBCT). Analysis of effluent samples following 30-sec EBCT treatment shows that even the shortest-chain PFSAs do not reach 50% breakthrough within the first 350,000 BVs, though differences in removal of short-chain PFCAs was less dramatic. The regenerable polyacrylic A860 resin performed very poorly compared to all polystyrene resins, with >90% breakthrough of all PFASs occurring within 10,000 BVs. The greater affinity of polystyrene resins is attributed to increased hydrophobic interactions in addition to electrostatic ion exchange. Analysis of breakthrough profiles reveals empirical correlation with ion exchange affinity coefficients (logK_ex) measured in batch experiments. Postmortem analysis of PFASs extracted from spent resins revealed chromatographic elution behavior and competition among PFASs for adsorption to the resins. PFSAs and long-chain PFCAs were preferentially adsorbed to earlier sections in the AER columns, whereas short-chain PFCAs were competitively displaced towards the later sections of the columns and into the effluent, consistent with effluent concentrations of the latter structures exceeding influent values. These results provide insights into the mechanisms that govern PFAS adsorption to AERs in real multisolute groundwater matrices and support findings from other diverse sites regarding PFAS affinity, elution behavior, and competition for exchange sites.

Assessment of perfluorohexane sulfonic acid (PFHxS)-related compounds degradation potential: Computational and experimental approaches

Perfluorohexane sulfonic acid (PFHxS) and PFHxS-related compounds are listed in Annex A of the Stockholm Convention without specific exemptions. Substances that potentially degrade to PFHxS are considered as their related compounds. Unfortunately, the degradation behavior of PFHxS precursors, an important basis for the corresponding chemical regulation, remains unclear. Herein, based on the hypothesis that bond dissociation enthalpy (BDE) is the determining factor for the degradation of PFHxS precursors, the BDE of PFHxS-related precursors to produceC6F13SO2-groups was calculated. In addition, quantitative structure-activity relationship models based on partial least squares, partial least squares discrimination analysis, and support vector machine algorithms were developed to predict the BDE of 48 PFHxS precursors and distinguish the precursors with different degradation potential. Subsequent photodegradation experiments demonstrated that the order of degradation rates was consistent with that predicted by theoretical models. Importantly, perfluorohexanoic acid (PFHxA) and perfluorobutanoic acid, and not PFHxS, were detected as the degradation products of potential PFHxS precursors. Sulfonamides, phenyl unit, and other radicals in the non-nucleus part of PFHxS precursors were identified as the critical molecular segments that affect their degradation potential. Ultimately, by comparing BDE values, it was theoretically speculated that PFHxS related compounds exhibit a greater potential to generate PFHxA than PFHxS. Results in this study indicated for the first time that not all the compounds containing C6F13SO2- groups were guaranteed to degrade into PFHxS under natural conditions.

Removal of perfluoroalkyl acids and dynamic succession of biofilm microbial communities in the decomposition process of emergent macrophytes in wetlands

Perfluoroalkyl acids (PFAAs) are emerging contaminants that pose significant environmental and health concerns. Water-sediment-macrophyte residue systems were established to clarify the removal efficiency of PFAAs, explore possible removal pathways, and profile the dynamic succession of biofilm microbial communities in the decomposition process. These systems were fortified with 12 PFAAs at three concentration levels. Iris pseudacorus and Alisma orientale were selected as the decomposing emergent macrophytes. The removal rates in the treatments with residues of I. pseudacorus (IP) and A. orientale (AO) were 34.4% to 88.9% and 36.5% to 89.9%, respectively, which were higher than those in the control groups (CG) (30.3% to 86.9%), suggesting that decomposition could alter the removal of PFAAs. Sediment made the greatest contributions (preloaded 14.5% to 77.8% of PFAAs in IP, 14.3% to 78.2% in AO, and 27.4% to 71.9% in CG). PFAAs could also be removed by macrophyte residue sorption (0.0190% to 13.0% in IP and 0.016% to 15.6% in AO) and bioaccumulation of residual biofilm (the contributions of biofilm microbes and their extracellular polymeric substances were 0.0110% to 3.93% and 0.918% to 34.4%, respectively, in IP and 0.0141% to 4.65% and 1.49% to 34.1%, respectively, in AO). Significant correlations were observed between sediment/residue adsorption and bioaccumulation of biofilm microbes, and were significantly correlated with perfluoroalkyl chain length (p < 0.05). The dynamic succession of residual biofilm microbial communities was investigated. The largest difference was found at the preliminary stage. The most similar communities were found in AO on day 70 (with specific genera Macellibacteroides and WCHB1-32) and in IP on day 35 (with specific genera Aeromonas and Flavobacterium). This study is useful to understand the removal of PFAAs during the decomposition process, providing further assistance in removing PFAAs during the life cycle of macrophytes in wetlands.

The role of dissolved organic matter during Per- and Polyfluorinated Substance (PFAS) adsorption, degradation, and plant uptake: A review

The negative effects of polyfluoroalkyl substances (PFAS) on the environment and health have recently attracted much attention. This article reviews the influence of soil- and water-derived dissolved organic matter (DOM) on the environmental fate of PFAS. In addition to being co-adsorped with PFAS to increase the adsorption capacity, DOM competes with PFAS for adsorption sites on the surface of the material, thereby reducing the removal rate of PFAS or increasing water solubility, which facilitates desorption of PFAS in the soil. It can quench some active species and inhibit the degradation of PFAS. In contrast, before DOM in water self-degrades, DOM has a greater promoting effect on the degradation of PFAS because DOM can complex with iron, iodine, among others, and act as an electron shuttle to enhance electron transfer. In soil aggregates, DOM can prevent microorganisms from being poisoned by direct exposure to PFAS. In addition, DOM increases the desorption of PFAS in plant root soil, affecting its bioavailability. In general, DOM plays a bidirectional role in adsorption, degradation, and plant uptake of PFAS, which depends on the types and functional groups of DOM. It is necessary to enhance the positive role of DOM in reducing the environmental risks posed by PFAS. In future, attention should be paid to the DOM-induced reduction of PFAS and development of a green and efficient continuous defluorination technology.

Occurrence and Distribution of Per- and Polyfluoroalkyl Substances from Multi-Industry Sources to Water, Sediments and Plants along Nairobi River Basin, Kenya

Per- and polyfluoroalkyl substances (PFAS) are ever-present pollutants in the environment. They are persistent and bio-accumulative with deleterious health effects on biota. This study assesses the levels of PFAS in environmental matrices along the Nairobi River, Kenya. An aggregate of 30 PFAS were determined in water, while 28 PFAS were detected in sediments and plants using solid phase extraction then liquid chromatography–mass spectrometric techniques. In water, higher levels of perfluoroundecanoic acids of up to 39.2 ng L−1 were observed. Sediment and plant samples obtained in the midstream and downstream contained higher levels of perfluorooctanoic acid of up to 39.62 and 29.33 ng g−1, respectively. Comparably, levels of long-chain PFAS were higher in water and sediments than in plants. Sediment/water log distribution of selected PFAS ranged between 2.5 (perfluoroundecanoic acid) and 4.9 (perfluorooctane sulfonate). The level of perfluorooctane sulfonate (1.83 ng L−1) in water is above the acceptable level in surface water posing high human health and ecological risks. The observed PFAS concentrations and distribution were attributed mainly to multi-industries located along the river, among other sources. The knowledge of PFAS occurrence and distribution in Nairobi River, Kenya, provides important information to local regulatory agencies for PFAS pollution control.

Air-water interfacial adsorption of C4-C10 perfluorocarboxylic acids during transport in unsaturated porous media

The impact of chain length on air-water interfacial adsorption of perfluorocarboxylic acids (PFCAs) during transport in unsaturated quartz sand was investigated. Short-chain (C4-C7: PFBA, PFPeA, PFHxA, PFHpA) and long chain (C8-C10: PFOA, PFNA, PFDA) PFCAs were selected as a representative homologous series. Surface tensions were measured to characterize surface activities of the selected PFCAs. Miscible-displacement column experiments were conducted for each of the PFCAs to characterize the magnitudes of air-water interfacial adsorption under transport conditions. The transport of the long-chain PFCAs exhibited greater retardation than the short-chain PFCAs. Air-water interfacial adsorption (AWIA) was the predominant source of retention (≥63%) for the long-chain PFCAs. Conversely, AWIA contributed less to retention than did solid-phase sorption for the short-chain PFCAs, with the former contributions ranging from 4% to 40%. Direct examination of the breakthrough-curve profiles as well as mathematical-modeling results demonstrated that transport of the two longest-chain PFCAs was influenced by nonlinear AWIA, whereas that of the shorter-chain PFCAs was not. This disparate behavior is consistent with the input concentration used for the transport experiments in comparison to the respective surface activities and critical reference concentrations of the different PFCAs. Quantitative-structure/property-relationship (QSPR) analysis was applied to characterize the influence of molecular size on air-water interfacial adsorption. The logs of the air-water interfacial adsorption coefficients (K_ia) determined from the transport experiments are a monotonic function of molar volume, consistent with prior QSPR analyses of surface-tension measured values. The K_ia values determined from the transport experiments are very similar to those measured from surface-tension data, indicating that the transport experiments produced robust measurements of AWIA.

Assessment of Mobilization Potential of Per- and Polyfluoroalkyl Substances for Soil Remediation

This study investigated the mobilization of a wide range of per- and polyfluoroalkyl substances (PFASs) present in aqueous film-forming foams (AFFFs) in water-saturated soils through one-dimensional (1-D) column experiments with a view to assessing the feasibility of their remediation by soil desorption and washing. Results indicated that sorption/desorption of most of the shorter-carbon-chain PFASs (C ≤ 6) in soil reached greater than 99% rapidly─after approximately two pore volumes (PVs) and were well predicted by an equilibrium transport model, indicating that they will be readily removed by soil washing technologies. In contrast, the equilibrium model failed to predict the mobilization of longer-chain PFASs (C ≥ 7), indicating the presence of nonequilibrium sorption/desorption (confirmed by a flow interruption experiment). The actual time taken to attain 99% sorption/desorption was up to 5 times longer than predicted by the equilibrium model (e.g., ∼62 PVs versus ∼12 PVs predicted for perfluorooctane sulfonate (PFOS) in loamy sand). The increasing contribution of hydrophobic interactions over the electrostatic interactions is suggested as the main driving factor of the nonequilibrium processes. The inverse linear relationship (R² = 0.6, p < 0.0001) between the nonequilibrium mass transfer rate coefficient and the Freundlich sorption coefficient could potentially be a useful means for preliminary evaluation of potential nonequilibrium sorption/desorption of PFASs in soils.

Electrochemical oxidation processes for PFAS removal from contaminated water and wastewater: fundamentals, gaps and opportunities towards practical implementation

Electrochemical oxidation (EO) is emerging as one of the most promising methods for the degradation of recalcitrant per- and poly-fluoroalkyl substances (PFASs) in water and wastewater, as these compounds cannot be effectively treated with conventional bio- or chemical approaches. This review examines the state of the art of EO for PFASs destruction, and comprehensively compares operating parameters and treatment performance indicators for both synthetic and real contaminated water and wastewater media. The evaluation shows the need to use environmentally-relevant media to properly quantify the effectiveness/efficiency of EO for PFASs treatment. Additionally, there is currently a lack of quantification of sorption losses, resulting in a likely over-estimation of process' efficiencies. Furthermore, the majority of experimental results to date indicate that short-chain PFASs are the most challenging and need to be prioritized as environmental regulations become more stringent. Finally, and with a perspective towards practical implementation, several operational strategies are proposed, including processes combining up-concentration followed by EO destruction.

Perfluoroalkyl and polyfluoroalkyl substances (PFASs) in groundwater: current understandings and challenges to overcome

Perfluoroalkyl and polyfluoroalkyl substances (PFASs) have been frequently detected in groundwater globally. With the phase-out of perfluorooctane sulfonate (PFOS) and perfluorooctanate (PFOA) due to their risk to the ecosystem and human population, various novel PFASs have been used as replacements and detected in groundwater. In order to summarize the current understanding and knowledge gaps on PFASs in groundwater, we reviewed the studies about environmental occurrence, transport, and risk of legacy and novel PFASs in groundwater published from 1999 to 2021. Our review suggests that PFOS and PFOA could still be detected in groundwater due to the long residence time and the retention in the soil-groundwater system. Firefighting training sites, industrial parks, and landfills were commonly hotspots of PFASs in groundwater. More novel PFASs have been detected via nontarget analysis using high-resolution mass spectrometry. Some novel PFASs had concentrations comparable to that of PFOS and PFOA. Both legacy and novel PFASs can pose a risk to human population who rely on contaminated groundwater as drinking water. Transport of PFASs to groundwater is influenced by various factors, i.e., the compound structure, the hydrochemical condition, and terrain. The exchange of PFASs between groundwater and surface water needs to be better characterized. Field monitoring, isotope tracing, nontarget screening, and modeling are useful approaches and should be integrated to get a comprehensive understanding of PFASs sources and behaviors in groundwater.

Adsorption, Structure, and Dynamics of Short- and Long-Chain PFAS Molecules in Kaolinite: Molecular-Level Insights

The ubiquitous presence of poly- and perfluoroalkyl substances (PFAS) in different natural settings poses a serious threat to environmental and human health. Soils and sediments represent one of the important exposure pathways of PFAS for humans and animals. With increasing bioaccumulation and mobility, it is extremely important to understand the interactions of PFAS molecules with the dominant constituents of soils such as clay minerals. This study reports for the first time the fundamental molecular-level insights into the adsorption, interfacial structure, and dynamics of short- and long-chain PFAS molecules at the water-saturated mesopores of kaolinite clay using classical molecular dynamics (MD) simulations. At environmental conditions, all the PFAS molecules are exclusively adsorbed near the hydroxyl surface of the kaolinite, irrespective of the terminal functional groups and metal cations. The interfacial adsorption structures and coordination environments of PFAS are strongly dependent on the nature of the functional groups and their hydrophobic chain length. The formation of large, aggregated clusters of long-chain PFAS at the hydroxyl surface of kaolinite is responsible for their restricted dynamics in comparison to short-chain PFAS molecules. Such comprehensive knowledge of PFAS at the clay mineral interface is critical to developing novel site-specific degradation and mitigation strategies.

Field-Based Distribution and Bioaccumulation Factors for Cyclic and Aliphatic Per- and Polyfluoroalkyl Substances (PFASs) in an Urban Sedentary Waterbird Population

The field-based distribution and bioaccumulation factor (BAF) for per- and polyfluoroalkyl substances (PFASs) were determined in residential Black Swans (Cygnus atratus) from an urban lake (Melbourne, Australia). The concentrations of 46 aliphatic and cyclic PFASs were determined by HPLC-MS/MS in serum and excrement from swans, and water, sediment, aquatic macrophytes, soil, and grass samples in and around the lake. Elevated concentrations of ∑₄₆PFASs were detected in serum (120 ng mL^-1) and excrement (110 ng g^-1 dw) were strongly related indicating a potential noninvasive sampling methodology. Environmental concentrations of PFASs were consistent with a highly impacted ecosystem and notably high concentrations of perfluoro-4-ethylcyclohexanesulfonate (PFECHS, 67584-42-3; C₈HF₁₅SO₃) were detected in water (27 ng L^-1) and swan serum (16 ng mL^-1). In the absence of credible putative alternative sources of PFECHS input to the lake, we propose that the use of high-performance motorsport vehicles is a likely source of contamination to this ecosystem. The BAF of perfluorocarboxylic acids increased with each additional CF₂ moiety from PFOA (15.7 L kg^-1 ww) to PFDoDA (3615 L kg^-1 ww). The BAF of PFECHS was estimated as 593 L kg^-1 ww, which is lower compared with that of PFOS (1097 L kg^-1 ww).

Binding of per- and polyfluoroalkyl substances (PFASs) by organic soil materials with different structural composition - Charge- and concentration-dependent sorption behavior

The charge- and concentration-dependent sorption behavior of a range of per- and polyfluoroalkyl substances (PFASs) was studied for three organic soil samples with different organic matter quality, one Spodosol Oe horizon (Mor Oe) and two Sphagnum peats with different degrees of decomposition (Peat Oi and Peat Oe). Sorption to the two peat materials was, on average, four times stronger compared to that onto the Mor Oe material. In particular, longer-chained PFASs were more strongly bound by the two peats as compared to the Mor Oe sample. The combined results of batch sorption experiments and ¹³C NMR spectroscopy suggested sorption to be positively related to the content of carbohydrates (i.e., O-alkyl carbon). Sorption of all PFAS subclasses was inversely related to the pH value in all soils, with the largest pH effects being observed for perfluoroalkyl carboxylates (PFCAs) with C₁₀ and C₁₁ perfluorocarbon chain lengths. Experimentally determined sorption isotherms onto the poorly humified Peat Oi did not deviate significantly from linearity for most substances, while for the Mor Oe horizon, sorption nonlinearity was generally more pronounced. This work should prove useful in assessing PFAS sorption and leaching in organic soil horizons within environmental risk assessment.

Interactions between dissolved organic matter and perfluoroalkyl acids in natural rivers and lakes: A case study of the northwest of Taihu Lake Basin, China

Understanding the interactions between dissolved organic matter (DOM) and perfluoroalkyl acids (PFAAs) is essential for predicting the distribution, transport, and fate of PFAAs in aquatic environments. Based on field investigations in the northwest of Taihu Lake Basin combined with laboratory experiments, we obtained DOM and PFAA concentrations as well as compositions and investigated key factors of DOM affecting PFAA variability and capture of PFAAs by DOM. Results indicated that the total concentrations of PFAAs were 73.4-689 ng/L in surface water and that PFAAs were dominated by C3-7 perfluoroalkyl carboxylic acids and perfluorooctane sulfonic acid. The main components of DOM included tyrosine-, fulvic-, and tryptophan-like substances. The Mantel test revealed a significant positive correlation between DOM and PFAAs (P = 0.0001). Fulvic-like substances were identified as the most crucial factors affecting PFAA variability. The laboratory experiments revealed that DOM can spontaneously aggregate into a microgel. Furthermore, 19.1-50.9% of PFAAs, DOM characteristic peaks, and several metals (Ca, Mg, Cu, and Fe) can be removed during aggregation, indicating the capacity of DOM binding organic/inorganic substances. The fulvic-like substances were more effectively removed than the protein-like substances. The distribution coefficients of all PFAAs except perfluorohexanoic acid significantly correlated with their perfluorinated carbon numbers (r = 0.975, p<0.001). Our results provided insights into the interactions between DOM and PFAAs, improving the understanding of the distribution, transport, and fate of PFAAs in aquatic environments.

Target and Nontarget Screening of PFAS in Biosolids, Composts, and Other Organic Waste Products for Land Application in France

Zwitterionic, cationic, and anionic per- and polyfluoroalkyl substances (PFAS) are increasingly reported in terrestrial and aquatic environments, but their inputs to agricultural lands are not fully understood. Here, we characterized PFAS in 47 organic waste products (OWP) applied in agricultural fields of France, including historical and recent materials. Overall, 160 PFAS from 42 classes were detected from target screening and homologue-based nontarget screening. Target PFAS were low in agriculture-derived wastes such as pig slurry, poultry manure, or dairy cattle manure (median ∑₄₆PFAS: 0.66 μg/kg dry matter). Higher PFAS levels were reported in urban and industrial wastes, paper mill sludge, sewage sludge, or residual household waste composts (median ∑₄₆PFAS: 220 μg/kg). Historical municipal biosolids and composts (1976-1998) were dominated by perfluorooctanesulfonate (PFOS), N-ethyl perfluorooctanesulfonamido acetic acid (EtFOSAA), and cationic and zwitterionic electrochemical fluorination precursors to PFOS. Contemporaneous urban OWP (2009-2017) were rather dominated by zwitterionic fluorotelomers, which represented on average 55% of ∑₁₆₀PFAS (max: 97%). The fluorotelomer sulfonamidopropyl betaines (X:2 FTSA-PrB, median: 110 μg/kg, max: 1300 μg/kg) were the emerging class with the highest occurrence and prevalence in contemporary urban OWP. They were also detected as early as 1985. The study informs for the first time that urban sludges and composts can be a significant repository of zwitterionic and cationic PFAS.

Removal of Zwitterionic PFAS by MXenes: Comparisons with Anionic, Nonionic, and PFAS-Specific Resins

Zwitterionic per- and polyfluoroalkyl substances are increasingly detected in aquatic environments. The magnitude of their concentration and increased frequency of detection worldwide raise questions on their presence in drinking water and associated health risk. Scientific knowledge on the identification of treatment technologies to effectively capture such zwitterionic PFAS from contaminated water sources remains largely unknown. In this study, we investigated the application of anionic organic scavenger ion exchange (IX) resins (A860), nonionic IX resins (XAD 4 and XAD 7), PFAS-specific resins (A694 and A592), and Ti₃C₂ MXenes (novel two-dimensional metal carbides) for the removal of select fluorotelomer zwitterionic PFAS from natural waters. The cumulative removal of zwitterionic PFAS at pH ∼ 7 follows the order: Ti₃C₂ MXenes > A694 > A592 > A860 > XAD 4 ∼ XAD 7. Ti₃C₂ MXenes were able to capture >75% of the total influent zwitterionic PFAS and the performance remained consistent in natural and synthetic water. Ti₃C₂ MXenes also exhibited efficient regeneration (>90% recovery) with 0.4 M Na₂SO₃ solution, while the regeneration efficacy of other IX resins generally remained below 20%. Treatment with ∼180 J/cm² UV dosage in the 0.4 M Na₂SO₃ regenerant brine solution yielded >99.9% reduction in the zwitterionic PFAS concentration indicating that UV-sulfite systems exhibit promising potential for the treatment of zwitterionic PFAS concentrates.

Insights into the effects of salinity on the sorption and desorption of legacy and emerging per-and polyfluoroalkyl substances (PFASs) on marine sediments

Per-and polyfluoroalkyl substances (PFASs) have attracted extensive attention since this century due to their wide distribution, persistence, bioaccumulation/biomagnification potential, and (eco)toxicity. In the present study, we investigated the sorption kinetics, sorption isotherms and desorption behaviors of legacy and emerging PFASs with different chain lengths and functional end groups onto marine sediments at four different salinities (0, 10, 20, and 30 practical salinity units (psu)). Results revealed that the sorption of PFASs onto sediment can be well described by the pseudo-second-order kinetic model. PFASs sorption was influenced by both compound-specific and solution-specific parameters. The distribution coefficient (K_d) for PFASs were increased with the increase of perfluorocarbon chain length and salinity, suggesting that hydrophobic and electrostatic interactions were involved in the adsorption process. 6:2 FTSA showed the lowest adsorption among PFASs with eight carbon atoms (6:2 FTSA, PFOA and PFOS). The increase of perfluorocarbon chain length of PFASs and salinity would result in the decrease of desorption rate of PFASs from sediment. In addition, PFCAs were desorbed more easily from the sediment than the PFSAs with the same perfluorocarbon chain length at all salinity groups. The present study demonstrated that salinity can apparently influence the fate of PFASs in aquatic environment and provided valuable data for modeling the fate of PFASs in real environment.

An introduction to the sources, fate, occurrence and effects of endocrine disrupting chemicals released into the environment

Many classes of compounds are known or suspected to disrupt the endocrine system of vertebrate and invertebrate organisms. This review of the sources and fate of selected endocrine disrupting chemicals (EDCs) in the environment includes classes of compounds that are "legacy" contaminants, as well as contaminants of emerging concern. EDCs included for discussion are organochlorine compounds, halogenated aromatic hydrocarbons, brominated flame retardants, per- and polyfluoroalkyl substances, alkylphenols, phthalates, bisphenol A and analogues, pharmaceuticals, drugs of abuse and steroid hormones, personal care products, and organotins. An exhaustive survey of the fate of these contaminants in all environmental media (e.g., air, water, soil, biota, foods and beverages) is beyond the scope of this review, so the priority is to highlight the fate of EDCs in environmental media for which there is a clear link between exposure and endocrine effects in humans or in biota from other taxa. Where appropriate, linkages are also made between the fate of EDCs and regulatory limits such as environmental quality guidelines for water and sediments and total daily intake values for humans.

Increasing ionic strength and valency of cations enhance sorption through hydrophobic interactions of PFAS with soil surfaces

The effect of soluble cations on sorption in soils of a range of anionic PFAS is not well studied. We investigated the role of three common cations (Na⁺, Ca²⁺, and Mg²⁺) at varying solution concentrations on the sorption coefficients (K_d) of 18 anionic PFAS in two contrasting soils. The effective charge of the soil suspension (Zeta potential) became less negative as the concentration of these cations increased in the soil solutions. Perfluorinated compounds showed greater sorption than polyfluorinated compounds, with sulfonates of comparable chain lengths showing higher sorption than the carboxylates. We observed that the K_d values of several PFAS in the two soils were positively correlated with the concentration of cations in solution, especially in the presence of polyvalent cations (Ca²⁺and Mg²⁺). The changes in sorption with cation concentration were more prominent for long-chain PFAS, with C > 10 PFAS being completely removed from solution at higher cation concentrations. The emerging PFAS (replacement compounds GenX and ADONA) showed negligible or little sorption (K_d < 0.6 L/kg). While several mechanisms contribute towards sorption of PFAS in the presence of cations, we conclude that the primary effect of cations is through screening of negative charges on head groups of PFAS and reorientation of molecules at the interface between organic matter surfaces and soil solution as well as charge neutralisation at soil solid surface. Screening of negative charges allows for greater hydrophobic interaction between hydrophobic tails of PFAS and soil surfaces resulting in greater sorption. Increasing cation concentrations in soil solutions could thus reduce mobility of PFAS through a soil profile.

A review on per- and polyfluorinated alkyl substances (PFASs) in microplastic and food-contact materials

Plastic, paper and cardboard are widely used as food contact materials (FCMs), due to its numerous favourable characteristics. However, they are usually coated with hazardous substances, such as per- and polyfluorinated alkyl substances (PFASs). PFASs, with its functional properties of oil- and water-repellency, can migrate from FCMs into the food and cause potential risk to human health. There are also increasing concerns about the harm that FCMs can cause to the environment. These concerns include accumulation of non-degradable plastics in the environment, generation of microplastics (MPs) and nanoplastics, and release of PFASs from FCMs. While many reviews have been conducted on PFASs in the environment, including their occurrence, fate, toxicity, biodegradation, migration in ecosystems and remediation technologies, a systematic review of PFASs in FCMs and MPs is currently lacking. In addition, our knowledge of the PFAS sorption processes on MPs is rather limited, and in particular their desorption processes. Thus, this review aims to (1) review the presence of various classes of PFASs in FCMs and their migration into food, (2) review the PFASs in MPs and summarize the sorption mechanisms, and factors that influence their sorption behaviour on MPs in the aquatic environment, and (3) identify the current research gaps and future research directions to predict the risks associated with the presence and sorption of PFASs in FCMs and MPs.

Co-occurrence and correlations of PFASs and chlorinated volatile organic compounds (cVOCs) in subsurface in a fluorochemical industrial park: Laboratory and field investigations

Fluorochemical industrial park (FIP) represents an important source of per- and polyfluoroalkyl substances (PFASs) and chlorinated volatile organic compounds (cVOCs). Exploring the co-occurrence and correlations of PFASs and cVOCs is a key step towards the understanding their distributions in the field. In this study, perfluorooctanoic acid (PFOA) was the dominant compound in groundwater and aquifer solids, and elevated concentrations of short-chain perfluoroalkyl carboxylic acids (PFCAs) and hexafluoropropylene oxide oligomers were also detected in the field, suggesting their wide applications as substitutes for PFOA. Correlation analyses between PFASs and cVOCs suggested that cVOCs had a significant influence on the distribution and composition of PFASs in the field. In addition, the presence of cVOCs in the form of dense non-aqueous-phase organic liquids (DNAPL) affected the distribution and migration of PFASs at various depths, as evidenced by the relatively high PFASs concentrations (204 μg/L) and PFOA abundance (85.4%) in the deep aquifer, likely due to DNAPL-water interfaces sorption or partition into bulk DNAPL. The log K_d values, determined in the laboratory, were found to increase in the presence of DNAPL, especially for PFOA, with more than one time higher than those of perfluorobutanoic acid (PFBA) and hexafluoropropylene oxide dimer acid (HFPO-DA). This conclusion further demonstrated that PFOA had a higher potential to participate into DNAPL, which can migrate with DNAPL to the deep aquifer, supporting the higher abundance of PFOA in the deep aquifer mentioned above. However, the log K_d-field values of PFBA and HFPO-DA in the field were higher than that of PFOA, and no significant correlations (p > 0.05) were found between log K_d-field values and the chain-length of PFCAs at various depths, suggesting that the phenomena observed in the field are a result of composite influencing factors.

Legacy and Emerging Per- and Polyfluoroalkyl Substances Behave Distinctly in Spatial Distribution and Multimedia Partitioning: A Case Study in the Pearl River, China

Per- and polyfluoroalkyl substances (PFASs) have attracted worldwide attention due to their ubiquitous occurrence, bioaccumulation, and toxicological effects, yet the fate of PFASs in a lotic ecosystem is largely unknown. To elucidate spatial distribution and multimedia partitioning of legacy and emerging PFASs in a lotic river flowing into an estuary, PFASs were synchronously analyzed in water, suspended particulate matter (SPM), sediment, and biota samples collected along Guangzhou reach of the Pearl River, South China. Geographically, the concentrations of PFASs in the water phase showed a decreasing trend from the upper and middle sections (urban area) to the down section (suburban area close to estuary) of the river. While perfluorooctanoic acid predominated in water and SPM, more diverse compositions were observed in sediment and biota with the increase in contributions of long-chain PFASs. Field-derived sediment-water partitioning coefficients (K_d) and bioaccumulation factors (BAFs) of PFASs increased with the increase in perfluorinated carbons. Besides hydrophobicity, water pH and salinity significantly affected the multimedia partitioning of PFASs in a lotic ecosystem. In addition, 87 homologues (63 classes) were identified as emerging PFASs in four media using suspect analysis. Interestingly, K_d and BAF of the emerging PFASs were often higher than legacy PFASs containing the same perfluorinated carbons, raising a special concern on the environmental risk of emerging PFASs.

Coupled photocatalytic alkaline media as a destructive technology for per- and polyfluoroalkyl substances in aqueous film-forming foam impacted stormwater

The release of aqueous film forming foam (AFFF) from fuel fire events, fire training events, and other activities has resulted in the presence of persistent and recalcitrant per- and polyfluoroalkyl substances (PFAS) in soil and water nationwide. This study describes the degradation and defluorination of PFAS in stormwater collected from an AFFF-impacted site. Silica-based granular media (SGM) containing titanium dioxide was packed into a column reactor and placed between ultraviolet (UV) lamps to excite the photocatalyst within the SGM and generate free radicals to degrade PFAS present in water that was passed through the media. The system was amended with nucleophiles (hydroxyls) to facilitate the destruction of PFAS. Results showed rapid degradation of 17 identified PFAS, including perfluoroalkyl acid (PFAA) precursors, perfluorosulfonic acids (PFSAs), and perfluorocarboxylic acids (PFCAs). Significant defluorination was observed, indicating PFAS destruction as a result of the coupled photocatalytic and nucleophilic attack. Column reactor experiment findings indicate SGM in the presence of UV light passively degraded a mixture of PFAS in a concentrated waste stream at ambient conditions.

Electrokinetic remediation for removal of per- and polyfluoroalkyl substances (PFASs) from contaminated soil

Uncontrolled use and disposal of per- and polyfluoroalkyl substances (PFASs) in recent decades has resulted in extensive soil and groundwater contamination, necessitating counteraction. Electrokinetic remediation (EKR) offers a promising approach to in-situ soil remediation. Two novel modifications to conventional EKR were tested for the first time in a laboratory-scale study, to explore the capacity of EKR for PFAS removal. The first modification was a two-compartment setup designed for PFAS extraction from soil to an electrolyte-filled chamber. The second was a single-compartment setup designed to transport and confine contaminants in a chamber filled with granular activated carbon (GAC), thus, combining extraction with stabilisation. Electromigration varied for individual compounds, based mainly on perfluorocarbon chain length and functional group. The results indicated up to 89% concentration and extraction of ∑PFASs for the two-compartment setup, with removal efficiency reaching 99% for individual PFASs with C ≤ 6. Removed PFASs were concentrated adjacent to the anode at the anion exchange membrane, while short-chain compounds were extracted in the anolyte. The single-compartment setup achieved 75% extraction and accumulation of ∑PFASs in GAC. This demonstrates, for the first time, good effectiveness of coupling EKR with AC stabilisation for PFAS removal from soil. Perfluorocarbon chain length was a dominant factor affecting treatment efficiency in both setups, with very high removal rates for short-chain PFASs.

Implication of cation-bridging interaction contribution to sorption of perfluoroalkyl carboxylic acids by soils

Sorption of four perfluoroalkyl carboxylic acids (PFCAs) including perfluoropentanoic acid, perfluoroheptanoic acid, perfluorodecanoic acid, and perfluorododecanoic acid by three soils with cation exchange sites occupied by K⁺, Ca²⁺, or Fe³⁺ was measured using the batch equilibration method. We hypothesize that partitioning in soil organic matters (SOM) is the primarily operative mechanism for PFCA sorption by K⁺-soils, and sorption by Ca²⁺- or Fe³⁺-soils could be enhanced via cation-bridging interaction. The measured sorption isotherms for all four PFCAs by soils were linear within the aqueous concentration between 0 and 60 μg/L, and the distribution coefficients ranged between 14.8 and 173 L/kg. Long-chain PFCAs manifested greater sorption by the soils with higher SOM content. Compared to sorption by K⁺-soils, sorption of PFCAs by Ca²⁺- and Fe³⁺-soils increased by 19.9-90.2% and 38.5-219%, respectively. The relative contributions of cation-bridging interaction to the overall PFCA sorption were estimated to be 16.6-48.7% for Ca²⁺-soils and 27.8-67.7% for Fe³⁺-soils. These results demonstrate that multivalent exchangeable cations could play an important role, yet previously ignored, in controlling sorption and transport of PFCAs in soils.

Removal potential of multiple perfluoroalkyl acids (PFAAs) by submerged macrophytes in aquatic environments: Tolerance of Vallisneria natans and PFAA removal in submerged macrophyte-microbiota systems

Perfluoroalkyl acids (PFAAs) have emerged as a global concern in aquatic environment remediation due to their abundance, persistence, bioaccumulation, and toxicity. To comprehensively understand the removal potential of multiple PFAAs by submerged macrophytes in aquatic environments, systematic investigations into the tolerance of the typical submerged macrophyte Vallisneria natans to 12 typical PFAAs and the removal capacity to PFAAs in V. natans-microbiota systems were carried out. Results showed that although PFAAs could induce the accumulation of hydrogen peroxide and malondialdehyde, V. natans was overall resistant to multiple PFAAs with natural concentrations. Catalase is one of the main strategies of V. natans to alleviate PFAA stress. Microbiota can remove 18.10-30.84% of the PFAAs from the water column. 24.35-73.45% of PFAAs were removed from water in V. natans-microbiota systems. The uptake of plant tissues and the bioaccumulation of microbiota were proposed as the main removal processes. The removal rates were significantly correlated with the perfluorinated carbon atoms numbers (p < 0.05). PFAAs and V. natans increased the relative abundance of Betaproteobacteria, Nostocales, Microscillaceae, Sphingobacteriales, SBR1031, Chlamydiales, Phycisphaerae, Caldilineales, Rhodobacterales, and Verrucomicrobiales. The present study suggested that V. natans can be a potential species to remove multiple PFAAs in aquatic environments, and further providing insights into the PFAAs' remediation.

Per- and polyfluoroalkyl substances in the environment

Over the past several years, the term PFAS (per- and polyfluoroalkyl substances) has grown to be emblematic of environmental contamination, garnering public, scientific, and regulatory concern. PFAS are synthesized by two processes, direct fluorination (e.g., electrochemical fluorination) and oligomerization (e.g., fluorotelomerization). More than a megatonne of PFAS is produced yearly, and thousands of PFAS wind up in end-use products. Atmospheric and aqueous fugitive releases during manufacturing, use, and disposal have resulted in the global distribution of these compounds. Volatile PFAS facilitate long-range transport, commonly followed by complex transformation schemes to recalcitrant terminal PFAS, which do not degrade under environmental conditions and thus migrate through the environment and accumulate in biota through multiple pathways. Efforts to remediate PFAS-contaminated matrices still are in their infancy, with much current research targeting drinking water.

Anaerobic Microbial Dechlorination of 6:2 Chlorinated Polyfluorooctane Ether Sulfonate and the Underlying Mechanisms

The microbial transformation potential of 6:2 chlorinated polyfluorooctane ether sulfonate (6:2 Cl-PFESA) was explored in anaerobic microbial systems. Microbial communities from anaerobic wastewater sludge, an anaerobic digester, and anaerobic dechlorinating cultures enriched from aquifer materials reductively dechlorinated 6:2 Cl-PFESA to 6:2 hydrogen-substituted polyfluorooctane ether sulfonate (6:2 H-PFESA), which was identified as the sole metabolite by non-target analysis. Rapid and complete reductive dechlorination of 6:2 Cl-PFESA was achieved by the anaerobic dechlorinating cultures. The microbial community of the anaerobic dechlorinating cultures was impacted by 6:2 Cl-PFESA exposure. Organohalide-respiring bacteria originally present in the anaerobic dechlorinating cultures, including Geobacter, Dehalobacter, and Dehalococcoides, decreased in relative abundance over time. As the relative abundance of organohalide-respiring bacteria decreased, the rates of 6:2 Cl-PFESA dechlorination decreased, suggesting that the most likely mechanism for reductive dechlorination of 6:2 Cl-PFESA was co-metabolism rather than organohalide respiration. Reductive defluorination of 6:2 Cl-PFESA was not observed. Furthermore, 6:2 H-PFESA exhibited 5.5 times lower sorption affinity to the suspended biosolids than 6:2 Cl-PFESA, with the prospect of increased mobility in the environment. These results show the susceptibility of 6:2 Cl-PFESA to microbially mediated reductive dechlorination and the likely persistence of the product, 6:2 H-PFESA, in anaerobic environments.

Per- and Polyfluoroalkyl Substances in Contaminated Soil and Groundwater at Airports: A Canadian Case Study

The occurrence of 93 classes of per- and polyfluoroalkyl substances (PFASs) was investigated at aqueous film-forming foam (AFFF)-impacted sites of four Canadian airports. Surface/subsurface soil and groundwater samples were characterized using high-resolution mass spectrometry (HRMS) and an improved total oxidizable precursor (TOP) assay. PFAS profiles, loads, and spatial trends were highly site-specific, influenced by the AFFF use history, variations in sorption, transport, and in situ transformation potential of PFASs. All sites have been impacted by more than one AFFF chemistry, with the active firefighter training area exhibiting a greater PFAS variety and total PFAS burden than decommissioned sites. Zwitterionic and cationic compounds composed a large percentage (34.5-85.5%) of the total PFAS mass in most surface soil samples in the source zone but a relatively low percentage (<20%) in groundwater samples. Background soils surrounding the source zone contained predominantly unidentified precursors attributed to atmospheric deposition, while in AFFF-impacted soils, precursors originating from AFFFs can be largely captured by HRMS using available suspect lists. Horizontal transfer of PFASs in surface soils was limited, but vertical migration down the soil column occurred even in locations of low permeability. This study provides a critical data set to support developing new priority analyte lists and integrating TOP assay for comprehensive PFAS monitoring at AFFF-impacted sites.

Comparing the Leaching Behavior of Per- and Polyfluoroalkyl Substances from Contaminated Soils Using Static and Column Leaching Tests

Soil contaminated with aqueous film-forming foams (AFFFs) containing per- and polyfluoroalkyl substances (PFASs) at firefighting training sites has become a major concern worldwide. To date, most studies have focused on assessing soil-water partitioning behavior of PFASs and the key factors that can affect their sorption, whereas PFASs leaching from contaminated soils have not yet been widely investigated. This study evaluated the leaching and desorption of a wide range of PFASs from twelve contaminated soils using the Australian Standard Leaching Procedure (ASLP), the U.S. EPA Multiple Extraction Procedure (MEP), and Leaching Environmental Assessment Framework (LEAF). All three leaching tests provided a similar assessment of PFAS leaching behavior. Leaching of PFASs from soils was related to C-chain lengths and their functional head groups. While short-chain (CF₂ ≤ 6) PFASs were easily desorbed and leached, long-chain PFASs were more difficult to desorb. PFASs with a carboxylate head group were leached more readily and to a greater extent than those with a sulfonate or sulfonamide head group. Leaching of long-chain PFASs was pH-dependent where leaching increased at high pH, while leaching of short-chain PFASs was less sensitive to pH. Comparing different leaching tests showed that the results using the alkaline ASLP were similar to the cumulative MEP data and the former might be more practical for routine use than the MEP. No single soil property was adequately able to describe PFAS leaching from the soils. Overall, the PFAS chemical structure appeared to have a greater effect on PFAS leaching from soil than soil physicochemical properties.

Biochar sorption of perfluoroalkyl substances (PFASs) in aqueous film-forming foams-impacted groundwater: Effects of PFASs properties and groundwater chemistry

The widespread use of per- and polyfluoroalkyl substances (PFASs)-related products such as aqueous film-forming foams (AFFF) has led to increasing contamination of groundwater systems. The concentration of PFASs in AFFF-impacted groundwater can be several orders of magnitude higher than the drinking water standard. There is a need for a sustainable and effective sorbent to remove PFASs from groundwater. This work aims to investigate the sorption of PFASs in groundwater by biochar column. The specific objectives are to understand the influences of PFASs properties and groundwater chemistry to PFASs sorption by biochar. The PFASs-spiked Milli-Q water (including 19 PFASs) and four aqueous film-forming foams (AFFF)-impacted groundwater were used. The partitioning coefficients (log K_d) of long chain PFASs ranged from 0.77 to 4.63 while for short chain PFASs they remained below 0.68. For long chain PFASs (C ≥ 7), log K_d increased by 0.5 and 0.8 for each CF₂ moiety of PFCAs and PFSAs, respectively. Dissolved organic matter (DOM) was the most influential factor in PFASs sorption over pH, salinity, and specific ultraviolet absorbance (SUVA). DOM contained hydrophobic compounds and metal ions which can form DOM-PFASs complexes to provide more sorption sites for PFASs. The finding is useful for executing PFASs remediation by biochar filtration column, especially legacy long chain PFASs, for groundwater remediation.

Modeling PFAS Fate and Transport in Groundwater, with and Without Precursor Transformation

Groundwater professionals require tools to evaluate a variety of technical issues related to per- and polyfluoroalkyl substances (PFAS). These include the potential impact of PFAS precursors on groundwater plumes of perfluoroalkyl acids (PFAAs). Numerical modeling results show that, by adjusting the mass loading rate, source zones with or without a precursor can produce similar PFAA plumes. However, if a precursor is present, it can impact PFAA plume concentrations and extend PFAA plume durations by decades. Additional research regarding in situ precursor transformation rates-and improvements in source area characterization-will further advance the predictive value of modeling.