Room Temperature Gas Sensing of Two-Dimensional Titanium Carbide (MXene)

Dispersibility and Photochemical Stability of Delaminated MXene Flakes in Water

The environmental stability of 2D MXene flakes must be systematically studied before their further application. Herein, the colloidal dispersibility and photochemical stability of delaminated Ti₃ C₂ T_x MXene flakes modified with hydrazine (HMH) and KOH and with water as the control (HMH-Ti₃ C₂ , KOH-Ti₃ C₂ , and H₂ O-Ti₃ C₂ , respectively) are experimentally and theoretically studied. Modification greatly increases the dispersibility of Ti₃ C₂ T_x flakes. Their critical coagulation concentrations are 28.7, 106, and 49.1 mm NaCl, and their Hamaker constants are 23.7 × 10^-21 , 19.1 × 10^-21 , and 37.7 × 10^-21 J, respectively; the colloidal interaction follows the classical Derjaguin-Landau-Verwey-Overbeek theory. HMH-Ti₃ C₂ and KOH-Ti₃ C₂ exhibit higher photochemical stability, as indicated by their stronger resistance to oxidation under UV and visible light irradiation. Changes in their physicochemical properties and the generation of reactive oxygen species (ROS) are assayed. Spin-polarized density functional theory calculations and molecular dynamics simulations are used to determine the mechanisms underlying the differences in the photochemical stability of Ti₃ C₂ T_x flakes. K⁺ ions protect the flakes from oxidation by acting as a middle layer to reduce the coupling between Ti³⁺ and ROS, while HMH provides stronger protection by absorbing photoelectrons or reacting with ROS. These findings provide new insight into the environmental transformation and design of functional MXenes.

Young's Modulus and Tensile Strength of Ti3C2 MXene Nanosheets As Revealed by In Situ TEM Probing, AFM Nanomechanical Mapping, and Theoretical Calculations

Two-dimensional transition metal carbides, that is, MXenes and especially Ti₃C₂, attract attention due to their excellent combination of properties. Ti₃C₂ nanosheets could be the material of choice for future flexible electronics, energy storage, and electromechanical nanodevices. There has been limited information available on the mechanical properties of Ti₃C₂, which is essential for their utilization. We have fabricated Ti₃C₂ nanosheets and studied their mechanical properties using direct in situ tensile tests inside a transmission electron microscope, quantitative nanomechanical mapping, and theoretical calculations employing machine-learning derived potentials. Young's modulus in the direction perpendicular to the Ti₃C₂ basal plane was found to be 80-100 GPa. The tensile strength of Ti₃C₂ nanosheets reached up to 670 MPa for ∼40 nm thin nanoflakes, while a strong dependence of tensile strength on nanosheet thickness was demonstrated. Theoretical calculations allowed us to study mechanical characteristics of Ti₃C₂ as a function of nanosheet geometrical parameters and structural defect concentration.

High Anti-Interference Ti3C2Tx MXene Field-Effect-Transistor-Based Alkali Indicator

MXenes, a group of emerging two-dimensional (2D) transition metal carbides or nitrides, have attracted wide interest due to their unique structures and properties. Their stability and applicability in different media especially in an alkaline environment are directly associated with their potential applications and are not yet explored. Herein, a field-effect transistor (FET) is fabricated with single/double-layer Ti₃C₂T_x MXene. The Ti₃C₂T_x FET indicator shows a fast (∼1 s), sensitive, and selective response to alkali. Moreover, the device can work even in a high-salinity (2 M NaCl) environment, suggesting its high anti-interference ability for alkali in a high-ionic-strength environment. Using an in situ morphological image evolution study, it is demonstrated that the response signal results from alkali-induced denaturation of Ti₃C₂T_x nanosheets. The Ti₃C₂T_x-based alkali FET indicator and systematic evaluation on alkali-induced structure evolution of Ti₃C₂T_x provide essential insights into MXene-based FETs and future applications of MXene in alkaline environments.

2D Material Optoelectronics for Information Functional Device Applications: Status and Challenges

Graphene and the following derivative 2D materials have been demonstrated to exhibit rich distinct optoelectronic properties, such as broadband optical response, strong and tunable light-mater interactions, and fast relaxations in the flexible nanoscale. Combining with optical platforms like fibers, waveguides, grating, and resonators, these materials has spurred a variety of active and passive applications recently. Herein, the optical and electrical properties of graphene, transition metal dichalcogenides, black phosphorus, MXene, and their derivative van der Waals heterostructures are comprehensively reviewed, followed by the design and fabrication of these 2D material-based optical structures in implementation. Next, distinct devices, ranging from lasers to light emitters, frequency convertors, modulators, detectors, plasmonic generators, and sensors, are introduced. Finally, the state-of-art investigation progress of 2D material-based optoelectronics offers a promising way to realize new conceptual and high-performance applications for information science and nanotechnology. The outlook on the development trends and important research directions are also put forward.

Highly electrically conductive two-dimensional Ti3C2 Mxenes-based 16S rDNA electrochemical sensor for detecting Mycobacterium tuberculosis

Tuberculosis is one of the life-threatening infectious diseases caused by the obligate pathogenic bacterium Mycobacterium tuberculosis (M. tuberculosis). The current M. tuberculosis detection approaches cannot satisfy the requirement for early clinical diagnosis because of long detection time as well as low specificity. In our study, an electrochemical M. tuberculosis sensor was constructed by using specific fragment of 16S rDNA of M. tuberculosis H37Ra as target biomarker, peptide nucleic acid (PNA) as capture probe and highly conductive two-dimensional Ti₃C₂ MXenes as the signal amplified transduction material. After the hybridization between PNA and the specific fragment of 16S rDNA on the substrate of PNA-AuNPs nanogap network electrode, the target fragments were directly linked with conductive Ti₃C₂ MXenes by strong interactions between zirconium-cross-linked Ti₃C₂ MXenes and phosphate groups of the target fragments. The linking of Ti₃C₂ MXenes to the hybridized target fragments would bridge the gaps of the interrupted AuNPs in the nanogap network electrode and forming the conductive connection to cause the change in conductance between the electrodes. This conductance change could be used for M. tuberculosis detection. The limit of detection (LOD) of proposed method was 20 CFU mL^-1, and detection time was 2 h. Proposed method would find potential application in rapid detection of M. tuberculosis.

MXenes and Their Applications in Wearable Sensors

MXenes, a kind of two-dimensional material of early transition metal carbides and carbonitrides, have emerged as a unique class of layered-structured metallic materials with attractive features, as good conductivity comparable to metals, enhanced ionic conductivity, hydrophilic property derived from their hydroxyl or oxygen-terminated surfaces, and mechanical flexibility. With tunable etching methods, the morphology of MXenes can be effectively controlled to form nanoparticles, single layer, or multi-layer nanosheets, which exhibit large specific surface areas and is favorable for enhancing the sensing performance of MXenes based sensors. Moreover, MXenes are available to form composites with other materials facilely. With structure design, MXenes or its composite show enhanced mechanical flexibility and stretchability, which enabled its wide application in the fields of wearable sensors, energy storage, and electromagnetic shielding. In this review, recent progress in MXenes is summarized, focusing on its application in wearable sensors including pressure/strain sensing, biochemical sensing, temperature, and gas sensing. Furthermore, the main challenges and future research are also discussed.

Impact of Cation Intercalation on the Electronic Structure of Ti3C2Tx MXenes in Sulfuric Acid

Intercalation in Ti₃C₂T_x MXene is essential for a diverse set of applications such as water purification, desalination, electrochemical energy storage, and sensing. The interlayer spacing between the Ti₃C₂T_x nanosheets can be controlled by cation intercalation; however, the impact of intercalation on the Ti₃C₂T_x MXene chemical and electronic structures is not well understood. Herein, we characterized the electronic structure of pristine, Li-, Na-, K-, and Mg-intercalated Ti₃C₂T_x MXenes dispersed initially in water and 10 mM sulfuric acid (H₂SO₄) using X-ray absorption spectroscopy (XAS). The cation intercalation is found to dramatically influence the chemical environment of Ti atoms. The Ti oxidation of the MXene increases progressively upon intercalation of cations of larger sizes after drying in air, while interestingly a low Ti oxidation is observed for all intercalated MXenes after dispersion in diluted H₂SO₄. In situ XAS at the Ti L-edge was conducted during electrochemical oxidation to probe the changes in the Ti oxidation state in the presence of different cations in H₂SO₄ aqueous electrolyte. By applying the sensitivity of the Ti L-edge to probe the oxidation state of Ti atoms, we demonstrate that cation-intercalation and H₂SO₄ environment significantly alter the Ti₃C₂T_x surface chemistry.

Wearable Electronics Based on 2D Materials for Human Physiological Information Detection

Recently, advancement in materials production, device fabrication, and flexible circuit has led to the huge prosperity of wearable electronics for human healthcare monitoring and medical diagnosis. Particularly, with the emergence of 2D materials many merits including light weight, high stretchability, excellent biocompatibility, and high performance are used for those potential applications. Thus, it is urgent to review the wearable electronics based on 2D materials for the detection of various human signals. In this work, the typical graphene-based materials, transition-metal dichalcogenides, and transition metal carbides or carbonitrides used for the wearable electronics are discussed. To well understand the human physiological information, it is divided into two dominated categories, namely, the human physical and the human chemical signals. The monitoring of body temperature, electrograms, subtle signals, and limb motions is described for the physical signals while the detection of body fluid including sweat, breathing gas, and saliva is reviewed for the chemical signals. Recent progress and development toward those specific utilizations are highlighted in the Review with the representative examples. The future outlook of wearable healthcare techniques is briefly discussed for their commercialization.

Gas Sensors Based on Chemi-Resistive Hybrid Functional Nanomaterials

Chemi-resistive sensors based on hybrid functional materials are promising candidates for gas sensing with high responsivity, good selectivity, fast response/recovery, great stability/repeatability, room-working temperature, low cost, and easy-to-fabricate, for versatile applications. This progress report reviews the advantages and advances of these sensing structures compared with the single constituent, according to five main sensing forms: manipulating/constructing heterojunctions, catalytic reaction, charge transfer, charge carrier transport, molecular binding/sieving, and their combinations. Promises and challenges of the advances of each form are presented and discussed. Critical thinking and ideas regarding the orientation of the development of hybrid material-based gas sensor in the future are discussed.

Room-Temperature, Highly Durable Ti3C2Tx MXene/Graphene Hybrid Fibers for NH3 Gas Sensing

Graphene-based fibers (GFs) have aroused enormous interest in portable, wearable electronics because of their excellent mechanical flexibility, electrical conductivity, and weavability, which make them advantageous for wearable electronic devices. Herein, we report the development of metal binder-free Ti₃C₂T_x MXene/graphene hybrid fibers by a scalable wet-spinning process. These hybrid fibers exhibit excellent mechanical and electrical properties for applications in flexible wearable gas sensors. The synergistic effects of electronic properties and gas-adsorption capabilities of MXene/graphene allow the created fibers to show high NH₃ gas sensitivity at room temperature. The hybrid fibers exhibited significantly improved NH₃ sensing response (ΔR/R₀ = 6.77%) compared with individual MXene and graphene. The hybrid fibers also showed excellent mechanical flexibility with a minimal fluctuation of resistance of ±0.2% and low noise resistance even after bending over 2000 cycles, enabling gas sensing during deformation. Furthermore, flexible MXene/graphene hybrid fibers were woven into a lab coat, demonstrating their high potential for wearable devices. We envisage that these exciting features of 2D hybrid materials will provide a novel pathway for designing next-generation portable wearable gas sensors.

In Situ Growing Double-Layer TiO2 Nanorod Arrays on New-Type FTO Electrodes for Low-Concentration NH3 Detection at Room Temperature

A novel double-layer TiO₂ nanorod array (NRA) gas sensor for room-temperature detection of NH₃ was fabricated by employing etched fluorine-doped tin dioxide (FTO) glass as the in situ growing substrate and the new-type gas-sensing electrode via the facile droplet-coating and hydrothermal methods. Due to the synergistic effect of forces, special double-layer TiO₂ NRAs with a cross-linked and bridgelike structure is formed, in which adequate point junctions can be generated to construct self-assembled electron pathways required for gas-sensing tests. Gas-sensing tests indicate that all samples obtained at different growth times have an excellent gas-sensing response to low-concentration NH₃ at room temperature. Among them, the TiO₂ NRAs obtained at 6 h (S2) exhibit the highest gas-sensing response to 100 ppm NH₃ with a value of 102%. In addition, the growth mechanism, the gas reaction mechanism, and the effect of humidity on the gas-sensing performance are also discussed in the present paper.

Self-reduction bimetallic nanoparticles on ultrathin MXene nanosheets as functional platform for pesticide sensing

Two-dimensional (2D) transition metal carbides and nitrides, named MXene, appear promising application prospects in sensor filed. Metal nanoparticles, especially bimetallic nanoparticles, are the superior nanocatalyst, which process excellent features due to the high specific surface area and synergistic catalytic capacity. Using ultrathin MXene nanosheets as the natural reducing agent and support, we prepare the shape-controlled Au-Pd bimetallic nanoparticles via a self-reduction process at room temperature in a short time, which can well enhance the catalytic performance and are benefit for the acetylcholinesterase immobilization. Based on their desired properties, we propose a disposable electrochemical biosensor for the detection of organophosphorus pesticide using the multi-dimensional nanocomposites (MXene/Au-Pd) as the functional platform. Under the optimized conditions, our fabricated biosensor exhibits a favorable linear relationship with the concentration of paraoxon from 0.1 to 1000 μg L^-1, with a low detection limit of 1.75 ng L^-1. Furthermore, the biosensor can be applied for paraoxon detection in pear and cucumber samples, providing an effective and useful avenue for the applicability of novel 2D nanomaterials in biosensing field.

Stability and Sensing Enhancement by Nanocubic CeO2 with {100} Polar Facets on Graphene for NO2 at Room Temperature

Metal oxides with a polar surface interact strongly with polar NO₂ molecules, thus facilitating sensitive detection of NO₂. In this work, the composites comprising graphene and cubic CeO₂ nanoparticles with the {100} polar surface are prepared by a hydrothermal technique, and they exhibit fast response, excellent selectivity, stable recovery, and sensitive detection with a low detection limitation of 1 ppm for NO₂ at room temperature. According to the first-principle calculations, the adsorption energy of NO₂ on the CeO₂{100} polar surface is the most negative corresponding to the strongest interactions between them. The formation energy of oxygen vacancies (O_v) on the {100} polar plane is also negative, and the abundant O_v facilitates the adsorption of NO₂. The internal electric field near the polar surface promotes the charge separation and accelerates the charge exchange between NO₂ and the composites. In addition, graphene promotes electron transfer at the interface and improves the stability of the CeO₂{100} polar surface. The composites of graphene and metal oxides with a polar surface are excellent for NO₂ detection, and the discovery reveals a new sensing strategy.

State of the Art in Alcohol Sensing with 2D Materials

Since the discovery of graphene, the star among new materials, there has been a surge of attention focused on the monatomic and monomolecular sheets which can be obtained by exfoliation of layered compounds. Such materials are known as two-dimensional (2D) materials and offer enormous versatility and potential. The ultimate single atom, or molecule, thickness of the 2D materials sheets provides the highest surface to weight ratio of all the nanomaterials, which opens the door to the design of more sensitive and reliable chemical sensors. The variety of properties and the possibility of tuning the chemical and surface properties of the 2D materials increase their potential as selective sensors, targeting chemical species that were previously difficult to detect. The planar structure and the mechanical flexibility of the sheets allow new sensor designs and put 2D materials at the forefront of all the candidates for wearable applications. When developing sensors for alcohol, the response time is an essential factor for many industrial and forensic applications, particularly when it comes to hand-held devices. Here, we review recent developments in the applications of 2D materials in sensing alcohols along with a study on parameters that affect the sensing capabilities. The review also discusses the strategies used to develop the sensor along with their mechanisms of sensing and provides a critique of the current limitations of 2D materials-based alcohol sensors and an outlook for the future research required to overcome the challenges.

Dynamical Control over Terahertz Electromagnetic Interference Shielding with 2D Ti3C2Ty MXene by Ultrafast Optical Pulses

High electrical conductivity and strong absorption of electromagnetic radiation in the terahertz (THz) frequency range by metallic 2D MXene Ti₃C₂T_y make it a promising material for electromagnetic interference shielding, THz detectors, and transparent conducting electrodes. Here, we demonstrate that ultrafast optical pulses with wavelengths straddling the visible range (400 and 800 nm) induce transient broad-band THz transparency in the MXene that persists for nanoseconds. We demonstrate that optically induced transient THz transparency is independent of temperature from 95 to 290 K. This discovery opens new possibilities for development of switchable electromagnetic interference shielding materials and devices that can be rendered partially transparent on demand for transmitting THz signals, or for designing new THz devices such as sensitive optically gated detectors.

Gas adsorption properties (N2, H2, O2, NO, NO2, CO, CO2, and SO2) on a Sc2CO2 monolayer: a first-principles study

The selectivity of gas adsorption on the Sc₂CO₂ monolayer belongs to NO₂ and O₂.

Polyelectrolyte-grafted Ti3C2-MXenes stable in extreme salinity aquatic conditions for remediation of contaminated subsurface environments

Polyelectrolyte-grafted Ti₃C₂-MXenes display high colloidal stability and low adsorption to mineral substrates in extreme salinity aquatic media, while maintaining decent removal efficiency for aqueous organic dyes.

Ti3C2 MXene-Based Sensors with High Selectivity for NH3 Detection at Room Temperature

In this study, from experiments and theoretical calculation, we reported that Ti₃C₂ MXene can be applied as sensors for NH₃ detection at room temperature with high selectivity. Ti₃C₂ MXene, a novel two-dimensional carbide, was prepared by etching off Al atoms from Ti₃AlC₂. The as-prepared multilayer Ti₃C₂ MXene powders were delaminated to a single layer by intercalation and ultrasonic dispersion. The colloidal suspension of single-layer Ti₃C₂-MXene was coated on the surface of ceramic tubes to construct sensors for gas detection. Thereafter, the sensors were used to detect various gases (CH₄, H₂S, H₂O, NH₃, NO, ethanol, methanol, and acetone) with a concentration of 500 ppm at room temperature. Ti₃C₂ MXene-based sensors have high selectivity to NH₃ compared with other gases. The response to NH₃ was 6.13%, which was four times the second highest response (1.5% to ethanol gas). To understand the high selectivity, first-principles calculations were conducted to explore adsorption behaviors. From adsorption energy, adsorbed geometry, and charge transfer, it was confirmed that Ti₃C₂ MXene theoretically has a high selectivity to NH₃, compared with other gases in this experiment. Moreover, the response of the sensor to NH₃ increased almost linearly with NH₃ concentration from 10 to 700 ppm. The humidity tests and cycle tests of NH₃ showed that the Ti₃C₂ MXene-based gas sensor has excellent performances for NH₃ detection at room temperature.

Thickness biased capture of CO2 on carbide MXenes

The synthesis of two-dimensional transition metal carbides (MXenes) with a predefined number of atomic layers offers a possible way to tune these nanomaterials chemical activity. MXenes have been theoretically predicted to be able to store CO2 even at high temperatures and low CO2 partial pressures, a prediction which has been experimentally confirmed afterwards. In the present work, the influence of the number of atomic layers on CO2 adsorption is systematically investigated by means of density functional theory based calculations, using suitable periodic models representing the (0001) surface of a series of these materials with formula Mn+1Cn (M = Ti, Zr, Hf, V, Nb, Ta, Mo, W) and n = 1-3. The interaction of CO2 with the MXene surfaces is always favorable with the adsorption energy decreasing as the transition metal electronic configuration goes from d2 through d3 to d4, in agreement with previous work for n = 1. The influence of the thickness is found to be rather small, yet noticeable, although somewhat erratic. Nevertheless, the adsorption energy seems to converge to a defined clear limit for sufficiently thick MXenes. Interestingly, this value is close to that corresponding to the (111) surface of bulk Transition Metal Carbides (TMCs). The close structural similarity between the MXene (0001) and TMC (111) surfaces strongly suggests that the former provide a practical way to approach this otherwise unstable surface. The possibility to tune the CO2 interaction based on the MXene thickness is further investigated by means of kinetic phase diagrams. These provide additional evidence that carbide MXene surfaces are promising materials for CO2 capture even at low CO2 partial pressures, and that the MXene thickness can be used to fine tune this appealing behavior.

Future Applications of MXenes in Biotechnology, Nanomedicine, and Sensors

The past few years have seen significant developments in the chemistry and potential biological applications of 2D materials. This review focuses on recent advances in the biotechnological and biomedical applications of MXenes, which are 2D carbides, nitrides, and carbonitrides of transition metals. Nanomaterials based on MXenes can be used as therapeutics for anticancer treatment, in photothermal therapy as drug delivery platforms, or as nanodrugs without any additional modification. Furthermore, we discuss the potential use of these materials in biosensing and bioimaging, including magnetic resonance and photoacoustic imaging techniques. Finally, we present the most significant examples of the use of MXenes as efficient agents for environmental and antimicrobial treatments, as well as a brief discussion of their future prospects and challenges.

Interfacial Assembly of Ultrathin, Functional MXene Films

MXenes are a prominent family of two-dimensional materials because of their metallic conductivity and abundant surface functionalities. Although MXenes have been extensively studied as bulk particles or free-standing films, thin and transparent films are needed for optical, optoelectronic, sensing, and other applications. In this study, we demonstrate a facile method to fabricate ultrathin (∼10 nm), Ti₃C₂T_x MXene films by an interfacial assembly technique. The self-assembling behavior of MXene flakes resulted in films with a high stacking order and strong plane-to-plane adherence, where optimal films of 10 nm thickness displayed a low sheet resistance of 310 Ω/□. By using surface tension, films were transferred onto various types of planar and curved substrates. Moreover, multiple films were consecutively transferred onto substrates from a single batch of solution, showing the efficient use of the material. When the films were utilized as gas sensing channels, a high signal-to-noise ratio, up to 320, was observed, where the gas response of films assembled from small MXene flakes was 10 times larger than that from large flakes. This work provides a facile and efficient method to allow MXenes to be further exploited for thin-film applications.

Ti3 C2 MXene Paper for the Effective Adsorption and Controllable Release of Aroma Molecules

Olfactory sensing and perception play an important role in people's daily lives and greatly affects senses, emotions, and behavior. In particular, the development of the controlled release of aroma enhances human's well-being and strengthens interactions with surroundings through olfactory display, especial when combined with visual and audial cues. Here, Ti₃ C₂ MXene plays a dual-function role as the adsorption site of aroma molecules and the heating source for the controlled release of aroma molecules. Due to abundant termination groups on the surface and the metallic nature, Ti₃ C₂ MXene provides abundant active sites for the interaction with aroma molecules; simultaneously, MXene can be electrically heated to thermally desorb the aroma molecules from the interaction sites. This approach eliminates the interface incompatibility issues between the heating source and the molecular encapsulation layer in conventional olfactory display system. This work presents the controlled release of the aroma molecule phenethyl alcohol (PA) using Ti₃ C₂ MXene paper. Ti₃ C₂ MXene paper serves as the adsorption material and a heating source that achieves 100 °C within 1 s. The relative amount of PA released reaches nearly 100% after 1 min of heating.

Hollow-structured MXene-PDMS composites as flexible, wearable and highly bendable sensors with wide working range

Although versatile piezoresistive pressure sensors show a great potential as human motion detection and wearable smart devices, it is still an issue to widen their working range and enhance their sensitivity. Herein, hollow-structured MXene-polydimethylsiloxane composites (MPCs) are fabricated by utilizing nickel foam as the three-dimensional substrate for dip-coating of MXene sheets followed by infiltrating of polydimethylsiloxane and etching of the nickel foam substrate. The resultant MPC performs a wide working range with bending angles of 0° to 180°, an excellent long-term reliability up to 1000 cycles under the bending angles of 15°, 30° and 150°, and a stable durability with a bending angle of 30° in a frequency range from 0.05 to 2 Hz as a bendable piezoresistive pressure sensor, which is attributed to the formation of dense conduction paths due to the interconnection of MXene sheets during the deformation of MPC. The sensor also exhibits an extremely low detection limit of 10 mg for pressure detection. Interestingly, the slippage of adjacent MXene sheets is beneficial for monitoring slight vibration of equipments and detecting subtle human motions. Thus, the MPC sensor could be applied for stereo sound and ultrasonic vibration monitoring, swallowing, facial muscle movement, and various intense motion detections, demonstrating its great potential as wearable smart devices.

Adhesion of two-dimensional titanium carbides (MXenes) and graphene to silicon

Two-dimensional transition metal carbides (MXenes) have attracted a great interest of the research community as a relatively recently discovered large class of materials with unique electronic and optical properties. Understanding of adhesion between MXenes and various substrates is critically important for MXene device fabrication and performance. We report results of direct atomic force microscopy (AFM) measurements of adhesion of two MXenes (Ti3C2Tx and Ti2CTx) with a SiO2 coated Si spherical tip. The Maugis-Dugdale theory was applied to convert the AFM measured adhesion force to adhesion energy, while taking into account surface roughness. The obtained adhesion energies were compared with those for mono-, bi-, and tri-layer graphene, as well as SiO2 substrates. The average adhesion energies for the MXenes are 0.90 ± 0.03 J m-2 and 0.40 ± 0.02 J m-2 for thicker Ti3C2Tx and thinner Ti2CTx, respectively, which is of the same order of magnitude as that between graphene and silica tip.

Two-Dimensional Vanadium Carbide MXene for Gas Sensors with Ultrahigh Sensitivity Toward Nonpolar Gases

The sensitive detection of explosive and flammable gases is an extremely important safety consideration in today's industry. Identification of trace amounts of nonpolar analytes at ambient temperatures, however, is still a challenge because of their weak adsorption, and very few studies have been able to achieve it via a chemiresistive mechanism. Herein, we demonstrate the high performance of 2D vanadium carbide MXene (V₂CT _x) gas sensors with ultrahigh sensitivity toward nonpolar gases. The fabricated 2D V₂CT _x sensor devices consisting of single-/few-layer 2D V₂CT _x on polyimide film were able to detect both polar and nonpolar chemical species including hydrogen and methane with a very low limit of detection of 2 and 25 ppm, respectively, at room temperature (23 °C). The performance of the fabricated V₂CT _x gas sensors in detection of nonpolar gases surpasses that of previously reported state-of-the-art gas sensors based on other 2D materials.

Insights into the thermal and chemical stability of multilayered V2CTx MXene

We report on the thermal stability of multilayered V2CTx MXenes under different atmospheres by combining in situ Raman spectroscopy with ex situ X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM) in order to elucidate and monitor the molecular, electronic, and structural changes of both the surface and bulk of the V2CTx MXene which has recently received much attention. The MXene samples were heated up to 600 °C in inert (N2), oxidative (CO2, air), and reductive (H2) environments under similar conditions. In situ Raman showed that the V[double bond, length as m-dash]O vibration for two-dimensional vanadia is preserved up to 600 °C under N2, while its intensity reduces under H2. When heated above 300 °C under either CO2 or air, V2CTx slightly oxidizes or transforms into V2O5, respectively. Furthermore, SEM revealed the presence of an accordion-like layered structure for the MXene under N2 and H2, while under CO2 and air the layered structure collapses and forms VO2 (V4+) and V2O5 (V5+) crystals, respectively. XPS reveals that, regardless of the gas, surface V species oxidize above 300 °C during the dehydration process. Finally, we demonstrated that the partial dehydration of V2CTx results in the partial oxidation of the material, and the total dehydration is achieved once 700 °C is reached. We believe that our methodology is a unique alternative to tune the dehydration, oxidation, and properties of V2CTx, which allows for the expansion of applications of MXenes.

Enhanced Selectivity of MXene Gas Sensors through Metal Ion Intercalation: In Situ X-ray Diffraction Study

Gas molecules are known to interact with two-dimensional (2D) materials through surface adsorption where the adsorption-induced charge transfer governs the chemiresistive sensing of various gases. Recently, titanium carbide (Ti₃C₂T _x) MXene emerged as a promising sensing channel showing the highest sensitivity among 2D materials and unique gas selectivity. However, unlike conventional 2D materials, MXenes show metallic conductivity and contain interlayer water, implying that gas molecules will likely interact in a more complex way than the typical charge transfer model. Therefore, it is important to understand the role of all factors that may influence gas sensing. Here, we studied the gas-induced interlayer swelling of Ti₃C₂T _x MXene thin films and its influence on gas sensing performance. In situ X-ray diffraction was employed to simultaneously measure dynamic swelling behavior where Ti₃C₂T _x MXene films displayed selective swelling toward ethanol vapor over CO₂ gas. Results show that the controlling sodium ion concentration in the interlayers is highly important in tuning the swelling behavior and gas sensing performance. The degree of swelling matched well with the gas response intensity, and the highest gas selectivity toward ethanol vapor was achieved for Ti₃C₂T _x sensing channels treated with 0.3 mM NaOH, which also displayed the largest amount of swelling. Our results demonstrate that controlling the interlayer transport of Ti₃C₂T _x MXene is essential for enhancing the selective sensing of gas molecules.

Improvement of Gas and Humidity Sensing Properties of Organ-like MXene by Alkaline Treatment

Ti₃C₂T _x MXene with an organ-like structure was synthesized from Ti₃AlC₂ (MAX phase) through the typical hydrofluoric (HF) acid etching method. Ti₃C₂T _x MXene was further alkaline-treated with a sodium hydroxide solution to obtain alkalized Ti₃C₂T _x. Room-temperature planar-type gas- and humidity-sensing devices were also fabricated by utilizing Ti₃C₂T _x MXene and alkalized Ti₃C₂T _x sensing material based on the dip coating method, respectively. The intercalation of the alkali metal ion (Na⁺) and the increase of the surface terminal oxygen-fluorine ratio ([O]/[F]) in Ti₃C₂T _x can effectively improve humidity- and gas-sensing properties at room temperature. The developed alkalized Ti₃C₂T _x sensor exhibited excellent humidity-sensing characteristics (approximately 60 times response signal change) in the relative humidity (RH) with a range of 11-95% and considerable NH₃ sensing performance (28.87% response value to 100 ppm of NH₃) at room temperature. The improvement of NH₃ and humidity-sensing properties indicated that alkalized Ti₃C₂T _x has great potential in chemical sensors, especially in NH₃ and humidity sensors.

White Photoluminescent Ti3C2 MXene Quantum Dots with Two-Photon Fluorescence

A recently created class of inorganic 2D materials, MXenes, has become a subject of intensive research. Reducing their dimensionality from 2D to 0D quantum dots (QDs) could result in extremely useful properties and functions. However, this type of research is scarce, and the reported Ti3C2 MXene QDs (MQDs) have only shown blue fluorescence emission. This work demonstrates a facile, high-output method for preparing bright white emitting Ti3C2 MQDs. The resulting product is two layers thick with a lateral dimension of 13.1 nm. Importantly, the as prepared Ti3C2 MQDs present strong two-photon white fluorescence. Their fluorescence under high pressure is also investigated and it is found that the white emission is very stable and the pressure makes it possible to change from cool white emission to warm white emission. Hybrid nanocomposites are then fabricated by polymerizing Ti3C2 MQDs in polydimethylsiloxane (PDMS) solution, and the bright white emitting hybrid materials in white light-emitting diodes are used. This work provides a facile and general approach to modulate various nanoscale MXene materials, and could further aid the wide development of applications for MXene materials in various optical-related fields.

An investigation into the factors governing the oxidation of two-dimensional Ti3C2 MXene

Two-dimensional (2D) transition metal carbides (MXenes) exhibit outstanding performances in many applications, such as energy storage, optoelectronics, and electrocatalysts. However, colloidal solutions of Ti3C2Tx MXene flakes deteriorate rapidly under ambient conditions due to the conversion of the titanium carbide to titanium dioxide. Here, we discuss the dominant factors influencing the rate of oxidation of Ti3C2Tx MXene flakes, and present guidelines for their storage with the aim of maintaining the intrinsic properties of the as-prepared material. The oxidation stability of the Ti3C2Tx flakes is dramatically improved in a system where water molecules and temperature were well-controlled. It was found that aqueous solutions of Ti3C2Tx MXene can be chemically stable for more than 39 weeks when the storage temperature (-80 °C) is sufficiently low to cease the oxidation processes. It was also found that if the Ti3C2Tx flakes are dispersed in ethanol, the degradation process can be significantly delayed even at 5 °C. Moreover, the oxidation stability of the Ti3C2Tx flakes is dramatically improved in both cases, even in the presence of oxygen-containing atmosphere. We demonstrate practical applications of our approach by employing Ti3C2Tx in a gas sensor showing that when oxidation is inhibited, the device can retain the original electrical properties after 5 weeks of storage.

Single-Molecule Sensing Using Nanopores in Two-Dimensional Transition Metal Carbide (MXene) Membranes

Label-free nanopore technology for sequencing biopolymers such as DNA and RNA could potentially replace existing methods if improvements in cost, speed, and accuracy are achieved. Solid-state nanopores have been developed over the past two decades as physically and chemically versatile sensors that mimic biological channels, through which transport and sequencing of biomolecules have already been demonstrated. Of particular interest is the use of two-dimensional (2D) materials as nanopore substrates, since these can in theory provide the highest resolution readout (<1 nm of a biopolymer segment) and opportunities for electronic multiplexed readout through their interesting electronic properties. In this work, we report on nanopores comprising atomically thin flakes of 2D transition metal carbides called MXenes. We demonstrate a high-yield (60%), contamination-free, and alignment-free transfer method that involves their self-assembly at a liquid-liquid interface to large-scale (mm-sized) films composed of sheets, followed by nanopore fabrication using focused electron beams. Our work demonstrates the feasibility of MXenes, a class of hydrophilic 2D materials with over 20 compositions known to date, as nanopore membranes for DNA translocation and single-molecule sensing applications.

Acidic Site-Assisted Ammonia Sensing of Novel CuSbS2 Quantum Dots/Reduced Graphene Oxide Composites with an Ultralow Detection Limit at Room Temperature

Novel CuSbS₂ quantum dots (QDs)/reduced graphene oxide (rGO) composites are self-assembled via a hot-injection method, and CuSbS₂ QDs exhibit a near monodispersion on the rGO surface. The gas sensors based on CuSbS₂ QDs/rGO composites show the relatively good gas responses toward NH₃ with an outstanding detection limit of 500 ppb and an average response time of 50 s at room temperature, and visible light illumination is proven to further promote the sensing performance of the composites. The study of the sensing mechanism reveals that the acidic sites on the surface play an extremely important role in NH₃ adsorption of the composites, and the reaction between NH₃ molecules and the pre-adsorbed oxygen ions finally leads to the generation of NO molecules. The synergistic effect existing between CuSbS₂ QDs and rGO, in terms of electron transfer, is certified as well.

Control of MXenes' electronic properties through termination and intercalation

MXenes are an emerging family of highly-conductive 2D materials which have demonstrated state-of-the-art performance in electromagnetic interference shielding, chemical sensing, and energy storage. To further improve performance, there is a need to increase MXenes' electronic conductivity. Tailoring the MXene surface chemistry could achieve this goal, as density functional theory predicts that surface terminations strongly influence MXenes' Fermi level density of states and thereby MXenes' electronic conductivity. Here, we directly correlate MXene surface de-functionalization with increased electronic conductivity through in situ vacuum annealing, electrical biasing, and spectroscopic analysis within the transmission electron microscope. Furthermore, we show that intercalation can induce transitions between metallic and semiconductor-like transport (transitions from a positive to negative temperature-dependence of resistance) through inter-flake effects. These findings lay the groundwork for intercalation- and termination-engineered MXenes, which promise improved electronic conductivity and could lead to the realization of semiconducting, magnetic, and topologically insulating MXenes.

High Sensitivity Surface Plasmon Resonance Sensor Based on Two-Dimensional MXene and Transition Metal Dichalcogenide: A Theoretical Study

MXene, a new class of two-dimensional nanomaterials, have drawn increasing attention as emerging materials for sensing applications. However, MXene-based surface plasmon resonance sensors remain largely unexplored. In this work, we theoretically show that the sensitivity of the surface plasmon resonance sensor can be significantly enhanced by combining two-dimensional Ti 3 C 2 T x MXene and transition metal dichalcogenides. A high sensitivity of 198 ∘ /RIU (refractive index unit) with a sensitivity enhancement of 41.43% was achieved in aqueous solutions (refractive index ∼1.33) with the employment of monolayer Ti 3 C 2 T x MXene and five layers of WS 2 at a 633 nm excitation wavelength. The integration of Ti 3 C 2 T x MXene with a conventional surface plasmon resonance sensor provides a promising approach for bio- and chemical sensing, thus opening up new opportunities for highly sensitive surface plasmon resonance sensors using two-dimensional nanomaterials.

Ti3C2T x-Based Three-Dimensional Hydrogel by a Graphene Oxide-Assisted Self-Convergence Process for Enhanced Photoredox Catalysis

Assembly of two-dimensional (2D) layered structures into three-dimensional (3D) macroscopic hydrogel has been an enduring attracting research theme. However, the anisotropic intersheet cross-linking to form Ti₃C₂T _x MXene-based hydrogel remains intrinsically challenging because of the superior hydrophilic nature of 2D Ti₃C₂T _x. Herein, Ti₃C₂T _x MXene is ingeniously assembled into the 3D macroscopic hydrogel under mild conditions by a graphene oxide (GO)-assisted self-convergence process. During the process, GO is reduced to reduced graphene oxide (RGO) by virtue of the reduction ability of Ti₃C₂T _x, leading to the partial removal of hydrophilic oxygen-containing groups and an increase of the hydrophobicity and the π-conjugated structures of RGO, which enables the assembly of RGO into a 3D RGO framework. Simultaneously, Ti₃C₂T _x is self-converged to be incorporated into the RGO framework by intimate interfacial interactions, thereby generating Ti₃C₂T _x-based hydrogel. The hydrogel with interconnected porous structure holds great potential as a promising material platform for photoredox catalysis. With the incorporation of Eosin Y photosensitizer, the functional Ti₃C₂T _x-based hydrogel exhibits enhanced photoactivity compared to the powder counterpart and features easy operability. This work enriches the rational utilization of GO/MXene colloid chemistry to design Ti₃C₂T _x MXene-based hydrogels with improved overall efficacy in practical applications.

Electrically-Transduced Chemical Sensors Based on Two-Dimensional Nanomaterials

Electrically-transduced sensors, with their simplicity and compatibility with standard electronic technologies, produce signals that can be efficiently acquired, processed, stored, and analyzed. Two dimensional (2D) nanomaterials, including graphene, phosphorene (BP), transition metal dichalcogenides (TMDCs), and others, have proven to be attractive for the fabrication of high-performance electrically-transduced chemical sensors due to their remarkable electronic and physical properties originating from their 2D structure. This review highlights the advances in electrically-transduced chemical sensing that rely on 2D materials. The structural components of such sensors are described, and the underlying operating principles for different types of architectures are discussed. The structural features, electronic properties, and surface chemistry of 2D nanostructures that dictate their sensing performance are reviewed. Key advances in the application of 2D materials, from both a historical and analytical perspective, are summarized for four different groups of analytes: gases, volatile compounds, ions, and biomolecules. The sensing performance is discussed in the context of the molecular design, structure-property relationships, and device fabrication technology. The outlook of challenges and opportunities for 2D nanomaterials for the future development of electrically-transduced sensors is also presented.

Promoting Role of MXene Nanosheets in Biomedical Sciences: Therapeutic and Biosensing Innovations

MXene nanosheets have emerged as biocompatible transition metal structures, which illustrate desirable performance for various applications due to their unique structural, physicochemical, and compositional features. MXenes are currently expanding their usage territory from mechanical, optical, chemical, and electronic fields toward biomedical areas. This is mainly originated from their large surface area and strong absorbance in near-infrared region, which in combination with their facile surface functionalization with various polymers or nanoparticles, make them promising nanoplatforms for drug delivery, cancer therapy, precise biosensing and bioimaging. The facile surface modification of the MXenes can mediate the better in vivo performance of them through reduced toxicity, enhanced colloidal stability, and extended circulation within the body. Herein, the synthesis and state-of-the-art progresses of MXene nanosheets designed for biomedical applications, including structural- and dose-dependent antimicrobial activity, photothermal therapy, drug delivery, and implants are emphasized. Furthermore, biosensing applications are highlighted and a comprehensive discussion on photoacoustic imaging, magnetic resonance imaging, computed tomography imaging, and optical imaging of MXenes is presented. The challenges and future opportunities of applying MXene nanomaterials in the area of biomedicine are also discussed.

Electronic and Optical Properties of 2D Transition Metal Carbides and Nitrides (MXenes)

2D transition metal carbides, carbonitrides, and nitrides, known as MXenes, are a rapidly growing family of 2D materials with close to 30 members experimentally synthesized, and dozens more studied theoretically. They exhibit outstanding electronic, optical, mechanical, and thermal properties with versatile transition metal and surface chemistries. They have shown promise in many applications, such as energy storage, electromagnetic interference shielding, transparent electrodes, sensors, catalysis, photothermal therapy, etc. The high electronic conductivity and wide range of optical absorption properties of MXenes are the key to their success in the aforementioned applications. However, relatively little is currently known about their fundamental electronic and optical properties, limiting their use to their full potential. Here, MXenes' electronic and optical properties from both theoretical and experimental perspectives, as well as applications related to those properties, are discussed, providing a guide for researchers who are exploring those properties of MXenes.

A Comparative Study of Interdigitated Electrode and Quartz Crystal Microbalance Transduction Techniques for Metal⁻Organic Framework-Based Acetone Sensors

We present a comparative study of two types of sensor with different transduction techniques but coated with the same sensing material to determine the effect of the transduction mechanism on the sensing performance of sensing a target analyte. For this purpose, interdigitated electrode (IDE)-based capacitors and quartz crystal microbalance (QCM)-based resonators were coated with a zeolitic⁻imidazolate framework (ZIF-8) metal⁻organic framework thin films as the sensing material and applied to the sensing of the volatile organic compound acetone. Cyclic immersion in methanolic precursor solutions technique was used for depositing the ZIF-8 thin films. The sensors were exposed to various acetone concentrations ranging from 5.3 to 26.5 vol % in N₂ and characterized/compared for their sensitivity, hysteresis, long-term and short-term stability, selectivity, detection limit, and effect of temperature. Furthermore, the IDE substrates were used for resistive transduction and compared using capacitive transduction.

Two-Dimensional Transition Metal Dichalcogenides and Metal Oxide Hybrids for Gas Sensing

Two-dimensional (2D) nanomaterials have demonstrated great potential in the field of gas sensing due to their layered structures. Especially for 2D transition metal dichalcogenides (TMDs), inherent high surface areas and their unique semiconducting properties with tunable band gaps make them compelling for sensing applications. In combination with the general benefits of 2D nanomaterials, the incorporation of metal oxides into 2D TMDs is a recent approach for improving the gas sensing performance of these materials by the synergistic effects of the hybridization. This Review aims to comprehend the sensing mechanisms and the synergistic effects of various hybridizations of 2D TMDs and metal oxides. The Review begins with the gas sensing mechanisms and synthesis methods of 2D TMDs. Achievements in recent research on 2D TMDs and their metal oxide hybrids for sensor applications are then comprehensively compiled. To clearly understand the collective benefits of TMDs and metal oxide hybrids, the hybridization effects are discussed in three aspects: geometrical, electronic, and chemical effects.

Enhanced Gas-Sensing Performance of GO/TiO₂ Composite by Photocatalysis

Few studies have investigated the gas-sensing properties of graphene oxide/titanium dioxide (GO/TiO₂) composite combined with photocatalytic effect. Room temperature gas-sensing properties of the GO/TiO₂ composite were investigated towards various reducing gases. The composite sensor showed an enhanced gas response and a faster recovery time than a pure GO sensor due to the synergistic effect of the hybridization, such as creation of a hetero-junction at the interface and modulation of charge carrier density. However, the issue of long-term stability at room temperature still remains unsolved even after construction of a composite structure. To address this issue, the surface and hetero-junction of the GO/TiO₂ composite were engineered via a UV process. A photocatalytic effect of TiO₂ induced the reduction of the GO phase in the composite solution. The comparison of gas-sensing properties before and after the UV process clearly showed the transition from n-type to p-type gas-sensing behavior toward reducing gases. This transition revealed that the dominant sensing material is GO, and TiO₂ enhanced the gas reaction by providing more reactive sites. With a UV-treated composite sensor, the function of identifying target gas was maintained over a one-month period, showing strong resistance to humidity.

Environment-Sensitive Photoresponse of Spontaneously Partially Oxidized Ti3C2 MXene Thin Films

A large family of two-dimensional transition metal carbides and nitrides (MXenes) has increasingly raised interest for electronic and optoelectronic applications due to their high electrical conductivity, potentially tunable electronic structure, nonlinear optical properties, and ability to be manufactured in the thin film state. During delamination and storage in ambient air environment, spontaneous oxidation of MXene flakes leads to formation of titanium oxide, a process that, as we demonstrate here, can be harnessed for manufacturing MXene-titania composites for optoelectronics, sensing, and other applications. We show that partially oxidized MXene thin films containing the in situ formed phase of titanium oxide have a significant photoresponse in the UV region of the spectrum. The relaxation process of photoexcited charge carriers takes a long time (∼24 h) but can be accelerated in the presence of oxygen and water vapor in the atmosphere. These properties of spontaneously formed MXene-titania thin films make them attractive materials for photoresistors with memory effect and sensitivity to the environment, as well as many other photo- and environment-sensing applications.