Amyloid-Like Protein Aggregates: A New Class of Bioinspired Materials Merging an Interfacial Anchor with Antifouling

Anti-fouling array paper-based device for rapid and accurate discrimination of foodborne pathogens in real samples

Foodborne pathogens contamination can cause serious food safety incidents. Early and rapid detection of foodborne pathogens is very important. Paper-based devices have been applied for on-site rapid detection of foodborne pathogens due to their cheapness and portability. However, the paper-based foodborne pathogen detection devices for real samples often receive interference, resulting in inaccurate detection results. In this study, bovine serum albumin (BSA) was modified on the surface of nitrocellulose membrane to construct anti-fouling sensing interface. Through array design, the anti-fouling array paper-based device (APAD) with multiple detection channels was constructed. The naked eye cut-off limits of the APAD were 102 colony forming units (cfu)/mL, 102 cfu/mL, and 103 cfu/mL for Staphylococcus aureus in orange juice, Escherichia coli O157: H7 in milk and orange juice, and Escherichia coli O157:H7 in soy sauce, respectively. The above results indicate that the APAD has good practical application potential in food safety.

Designing Amyloid-Like Protein Aggregates from Microalgal Biomass

Our societal dependence on petrochemical-derived plastics has significant environmental ramifications, with about 80% of such plastics ending up as persistent waste. To this end, we investigate the extraction and purification of proteins from microalgae, specifically spirulina and chlorella, and their self-assembly into amyloid-like aggregates as building blocks toward the development of sustainable bioplastic materials. After self-assembly, spirulina proteins formed beta-sheet-rich structures with a typical (albeit short and worm-like) fibrillar morphology, while chlorella proteins predominantly aggregated into nonfibrillar, spherical/annular structures. Despite their morphological differences, both microalgal protein aggregates exhibited impressive stability across a wide pH range, persisting up to pH 11 before disaggregating at pH 12. In short, this work highlights the importance of biomass source, protein purity, and composition on the aggregation process of differing proteins. Given the high protein content and expanding industrial production of microalgae, spirulina and chlorella present an untapped resource for the development of sustainable bioplastics.

Ultrasensitive Profiling of Plasma Extracellular Vesicles for Breast Cancer Subtyping with a High-Curvature Antifouling Nanoarray

Profiling of plasma extracellular vesicles (EVs) has long been hampered by their insufficient capture and assay sensitivity due to the high background of complex matrices. To address this challenge, we develop a high-curvature antifouling nanoarray electrochemical assay (eCAN) to enable ultrasensitive and specific profiling of plasma EVs for the accurate subtyping of breast cancer. This assay leverages a three-in-one multifunctional hierarchical antifouling nanofilm to improve EV capture, minimize nonspecific adsorption, and facilitate three-dimensional deposition of tyramine for signal amplification. These advantages allow the eCAN to achieve a sensitivity of up to 56 particles/mL (near a single-EV level), showing high specificity and anti-interference. The eCAN can differentiate EV subpopulations across different breast cancer cells and monitor their phenotypic changes. This assay allows accurate diagnosis and subtyping of breast cancer (AUC = 1.000) through direct profiling of EVs in undiluted plasma from a pilot cohort and provides a promising tool for precise diagnosis of cancers in clinical settings.

Protein aggregates facilitated by polar aprotic solvents as carriers for enzyme immobilization

Protein aggregates are extremely useful in fields such as bioseparation, biocatalysis, and bioadhesives. The development and use of protein aggregates, however, are in their infancy. In this study, emerging protein aggregates were developed through protein self-assembly using polar aprotic solvents coupled with halides. The polar aprotic solvent molecules, including dimethyl sulfoxide (DMSO), were inserted into the hydration shell of proteins such as ovalbumin (OVA), bovine serum albumin, and whey protein to partially exchange water molecules via van der Waals and electrostatic interactions to alter the surface polarity of the protein. Then, the halide ions were allowed to bind to proteins via electrostatic interactions and cause the self-assembly of proteins into aggregates. Under optimal conditions, the yield of OVA-DMSO protein aggregates reached 91.2 ± 1.52 %. OVA-DMSO-EDC/NHS-CA showed excellent enzymatic properties, and the production of calcium carbonate reached 7.1 ± 0.4 mg at 37 °C for 10 min. Additionally, other enzymes, such as L-TA, had high activity after being fixed with OVA-DMSO. These innovative protein aggregates are highly valuable for developing biomaterials.

One-step antifouling coating of polystyrene using engineered polypeptides

Unwanted nonspecific adsorption caused by biomolecules influences the lifetime of biomedical devices and the sensing performance of biosensors. Previously, we have designed B-M-E triblock proteins that rapidly assemble on inorganic surfaces (gold and silica) and render those surfaces antifouling. The B-M-E triblock proteins have a surface-binding domain B, a multimerization domain M and an antifouling domain E. Many biomedical technologies involve organic (polymeric) surfaces where B-M-E triblock proteins could potentially be used. In this study, we computationally and experimentally investigate the assembly of B-M-E triblock proteins on polystyrene (PS) surfaces, using PS-binding peptides as a surface-binding block B. We used atomic force microscopy, dynamic light scattering, fluorescence microscopy and quartz crystal microbalance to test the antifouling coating functionality. We found that, like for inorganic surfaces, the B-M-E proteins with PS-binding peptides as B block, form homogeneous monomolecular layers on PS surfaces with good stability against PBS washing. The adsorbed protein layer fully prevents adsorption of fluorescently labeled bovine serum albumin to PS microfluidic chips. Similarly, no significant fouling was observed using quartz crystal microbalance when 1 % (v/v) or 10 % (v/v) human serum were used as foulants.

Biomimetic Intrafibrillar Mineralization of Hierarchically Structured Amyloid-Like Fibrils

Intrafibrillar mineralization is essential not only as a fundamental process in forming biological hard tissues but also as a foundation for developing advanced composite fibril-based materials for innovative applications. Traditionally, only natural collagen fibrils have been shown to enable intrafibrillar mineralization, presenting a challenge in designing ordered hierarchical fibrils from common protein aggregation that exhibit similar high intrafibrillar mineralization activity. In this study, a mechanically directed two-step transformation method is developed that converts phase-transitioned protein nanofilms into crystalline, hierarchical amyloid-like fibrils with multilayer structures, which effectively control the growth and lateral organization of hydroxyapatite within adaptive gaps. The resulting mineralized HSAF achieves a hardness of 0.616 ± 0.007 GPa and a modulus of 19.06 ± 3.54 GPa-properties closely resembling native hard tissues-and exhibits exceptionally high bioactivity in promoting both native bone tissue growth and further intrafibrillar mineralization, achieving 76.9% repair in a mice cranial defect model after 8 weeks and outperforming other regenerative materials. This remarkable performance, stemming from the unique structure and composition of the fibers, positions HSAF as a promising candidate for biomedical and engineering applications. These findings advance the understanding of biomineralization mechanisms and establish a foundation for developing high-bioactivity materials for hard tissue regeneration.

Antimicrobial, remineralization, and infiltration: advanced strategies for interrupting dental caries

Dental caries, driven by plaque biofilm, poses a major oral health challenge due to imbalance in mineralization and demineralization. The primary objective in caries management is to maintain biofilm homeostasis while facilitating the repair and regeneration of dental hard tissues, thus restoring both structural integrity and functionality of affected teeth. Though antimicrobial and remineralization approaches haven shown promise, their standalone utilization without concurrent bacterial control or rebalancing lacks an integrated strategy to effectively arrest caries progression. Furthermore, according to the principles of minimally invasive dentistry, treatment materials should exhibit high permeability to ensure optimal sealing of demineralized tooth surfaces. The concept of interrupting dental caries (IDC) has emerged as a holistic approach, drawing upon extensive research encompassing three pivotal techniques: antibacterial strategies, remineralization therapies, and infiltration mechanisms, all of which are indispensable components in combating the progression of dental caries. In this review, we provide a comprehensive overview of the mechanisms and applications of antibacterial, remineralization, and infiltration technologies within the context of caries management. Additionally, we summarize advanced materials that align with the IDC concept, aiming to offer valuable insights for designing next-generation materials adept at preventing or halting caries progression efficiently.

Antifouling Polymer Coatings for Bioactive Surfaces

Bioactive surfaces play a pivotal role in biomedical applications by enabling precise biological interactions through immobilized functional molecules. However, their performance is often hindered by nonspecific protein adsorption and cell adhesion. Antifouling polymer coatings have emerged as an effective solution, creating hydration barriers to preserve functionality and reduce biofouling. This review provides an overview of the recent advances in the development of antifouling polymer coatings for bioactive surfaces, with particular focus on nonionic polymers, such as polyethylene glycol (PEG), and zwitterionic polymers like poly(2-methacryloyloxyethyl phosphorylcholine) (PMPC). Among them, zwitterionic polymers, with their unique charge-balanced structures, exhibit exceptional hydration, protein resistance, and stability, making them particularly promising for biomedical applications. In addition, key applications of these bioactive surfaces, including their use in anticoagulant materials, antibacterial coatings, and biosensor interfaces, are also discussed. The discussion concludes with an address of the field's challenges and future directions, highlighting the need for innovative materials that balance antifouling properties, biocompatibility, and long-term stability for both clinical and industrial use. This review aims to review the latest advancements in antifouling polymer coatings for bioactive surfaces and provide insights into optimizing multifunctional bioactive surfaces to meet the evolving and dynamic demands of the biomedical field.

Design and Application of Antifouling Bio-Coatings

Antifouling coatings stand out as one of the highly efficient ways to mitigate surface contamination. Traditional antifouling coatings have a major drawback: they rely on highly toxic and environmentally hazardous compounds. These substances not only lead to ecological harm but also disrupt the natural equilibrium of ecosystems. Consequently, in recent years, eco-friendly antifouling bio-coatings have emerged. This review focuses on the mechanisms and processes underlying contaminant adhesion, laying a solid foundation for grasping the principles of antifouling coating design. It further elaborates on the general strategies for developing bio-based antifouling solutions, highlighting their potential across a wide array of applications. Finally, this review carefully analyzes the current challenges confronted by antifouling bio-coatings and puts forward future development directions. Through a comprehensive overview, we aim to expand the influence of bio-based antifouling technologies, promote the further application of bio-based antifouling coatings in marine antifouling and medical antifouling fields, and provide examples for the establishment of environmental protection policies.

β-Lactoglobulin Forms a Conserved Fibril Core That Assembles into Diverse Fibril Polymorphs

The β-lactoglobulin (β-LG) protein, sourced from dietary products, is notable for forming amyloid fibrils, which are increasingly recognized as valuable protein-based nanomaterials due to their superior cytocompatibility, chemical resilience, and mechanical characteristics. However, the precise atomic details of β-LG's fibril assembly are not understood. In this study, we utilized cryo-electron microscopy to elucidate the composition and architecture of β-LG fibrils. We discovered that the β-LG fibril was rapidly assembled after a short time incubation. Remarkably, these fibril cores were composed of the first 32 residues, forming four β-strands that adopted a serpentine arrangement into a single protofilament. This protofilament core's stability was reinforced by hydrophobic interactions. Two identical protofilaments then align to form four distinct structural polymorphs through unique interfacial configurations, which were stabilized by hydrophilic interactions, hydrogen bonding, and electrostatic forces. Our findings provide a structural framework for understanding β-LG fibril formation and pave the way for designing innovative β-LG-based nanomaterials.

Extracellular Vesicles Separation and Biomedical Application Based on Affinity Recognition and Antifouling Coating Bifunctional Microsphere

Extracellular vesicles (EVs) are crucial mediators in various physiological and pathological processes, facilitating intercellular communication and offering potential as diagnostic disease markers. However, existing EVs separation methods have limitations that hinder their clinical application. In this study, we present a novel approach using bifunctional silica microspheres (SiO2-PTB-PS) for the specific, nondestructive isolation of EVs from complex biological media. The isolated EVs were subsequently used for direct cancer detection in clinical samples. The SiO2-PTB-PS microspheres, functionalized with a phosphatidylserine (PS) recognition peptide (PSpep), specifically bound to PS on the EVs surface. Additionally, an anti-adhesion coating on the silica microspheres minimized protein contamination, enhancing purity. This affinity-based recognition and antifouling strategy ensured high-purity EVs separation. Furthermore, we developed a detection system combining SiO2-PTB-PS microspheres with surface-enhanced Raman scattering (SERS) nanoprobes to identify protein tyrosine kinase 7 (PTK7) and epithelial cell adhesion (EpCAM) on the EVs membrane, achieving 80% precision in distinguishing cancer patients from healthy donors. The SiO2-PTB-PS microsphere system shows significant promise as a biotechnology tool, advancing the clinical application of EVs-based diagnostics.

Advanced Adaptive Protein Membrane with Super-High Flux and Precise Molecular Sieving of Dyes from Salts

Precise separation of small organic molecules and electrolyte salts is critical for various industrial processes, necessitating advanced membranes with uniform pores. Proteins, as one typical nature polymer having the exactly same structure and molecular weight, offer a promising material for making such membranes. Here, hemoglobin (BHb) and lysozyme (Lyz) are utilized to fabricate precise nanofiltration membranes through amyloid-like co-assembly, triggered by Tris(2-carboxyethyl) phosphine. Molecular dynamics simulations reveal that BHb intercalates between Lyz molecules, enhancing tight assembly and reducing defects. The Lyz/BHb membrane exhibits a high void volume of 27.2% and achieves an exceptional permeance of 335 L m-2 h-1 bar-1. Amazingly, the Lyz/BHb membrane achieves ultra-selective molecular sieving of dyes and salts with an unparalleled high separation factor of 1.25 × 103 for the NaCl/Brilliant blue. The unique adaptive separation layer is formed by anchoring dye molecules into the larger pores and thus narrowing down the pore size distribution and enhancing electrostatic repulsion, endowing the membrane with a distinctive molecular sieving of dyes and salts. This study offers valuable insights to finely tailor the pore structure of the membrane by co-assembly of proteins and to significantly enhance the membrane perm-selectivity by creating an adaptive protein separation layer with a unique molecular sieving property.

Complementary Peptide Interactions Support the Ultra-Rigidity of Polymers of De Novo Designed Click-Functionalized Bundlemers

Computationally designed 29-residue peptides yield tetra-α-helical bundles with D2 symmetry. The "bundlemers" can be bifunctionally linked via thiol-maleimide cross-links at their N-termini, yielding supramolecular polymers with unusually large, micrometer-scale persistence lengths. To provide a molecularly resolved understanding of these systems, all-atom molecular modeling and simulations of linked bundlemers in explicit solvent are presented. A search over relative orientations of the bundlemers identifies a structure, wherein at the bundlemer-bundlemer interface, interior hydrophobic residues are in contact, and α-helices are aligned with a pseudocontiguous α-helix that spans the interface. Calculation of a potential of mean force confirms that the structure in which the bundlemers are in contact and colinearly aligned is a stable minimum. Analyses of hydrogen bonds and hydrophobic complementarity highlight the complementary interactions at the interface. The molecular insight provided reveals the molecular origins of bundlemer alignment within the supramolecular polymers.

Photoinitiated Thiol-Ene Click Reaction for Preparation of Highly Adhesive and Mechanically Stable Silicone Coatings for Marine Antifouling and Anticorrosion

Marine biofouling and corrosion have become the main problems affecting the development of the marine industry. Silicone-based coatings have been widely used for antifouling and anticorrosion due to their low surface energy. However, the poor adhesion and low mechanical stability of these materials limit their application in complex marine environments. In this work, we presented a marine antifouling and anticorrosion coating named POSS-DMA@PDMS-TCM through photoinitiated thiol-ene click reaction combined with (mercaptopropyl) methylsiloxane dimethylsiloxane (PDMS-SH), dopamine methacrylamide (DMA), sulfhydryl-functionalized organosiloxanes (POSS-(SH)8), and N-(2,4,6-trichlorophenyl) maleimide (TCM). The POSS-DMA@PDMS-TCM coating exhibited strong stability and bonding ability both in air (2.17 MPa) and underwater (2.11 MPa) when the DMA content was 3 wt %. The high antibacterial (98.1% for Staphylococcus aureus and 99.5% for Escherichia coli) and antidiatom (94.5%) properties of the POSS-DMA@PDMS-TCM coatings have also been confirmed. Moreover, the POSS-DMA@PDMS-TCM coatings show excellent antifouling abilities in 120-day marine field tests, reducing fouling by 65.5% in comparison to the blank group. The coating also displayed superior anticorrosion performance with Ecorr values of -0.055 V, Icorr values of 7.67 × 10-6 , and Rp values of 3.10 × 105 Ω for Cu, which benefited from excellent chelating effect and liquid repellency. This study provides a novel strategy for the development of high-quality marine antifouling and anticorrosion coatings.

Nanomaterial-based synergistic strategies for combating dental caries: progress and perspectives

Dental caries, as the predominant global oral disease, remains a critical public health issue worldwide, particularly in socioeconomically disadvantaged communities. However, common caries prevention approaches (e.g., oral health education, mechanical plaque removal, and delivery of fluoride agents) are still insufficient for optimal caries management, and therefore, alternative regimens that can supplement existing strategies are highly warranted. Nanomaterials exhibit considerable potential in combating cariogenic pathogens and biofilms owing to their promising antimicrobial capacity, improved penetration into biofilms, targeted precision delivery, and versatile physicochemical properties. As unifunctional materials are limited in caries management, this review underscores the latest advancement in multifunctional anti-caries nanomaterials/nanomedicines. It highlights the cutting-edge materials developed or engineered to (i) incorporate diagnostic capabilities to prevent caries at an early stage, thus enhancing treatment efficiency, (ii) integrate mechanical "brushing" with anti-caries approaches to mechanochemically eradicate biofilms, (iii) exert antimicrobial/antibiofilm effects while preserving dental hard tissue. The current work also outlines future directions for optimizing nanosystems in the management of dental caries while emphasizing the need for innovative solutions to improve preventive and therapeutic efficacies.

Mechanically Robust, Superlubricating and Antifouling Bilayer Nanocoating for Micro-Bioimplants via a Dual-Function Metal Coordination Approach

Nanometer-thick ultrathin coatings with superior mechanical strength and desirable lubricating and antifouling performance are critical for the miniaturization of implantable medical devices. However, integrating these properties at the nanoscale remains challenging due to the inherent trade-off between mechanical strength and hydration as well as limitations in coating thickness. In this work, we address these challenges by employing dual-function metal coordination to construct a ∼25 nm thick bilayer structure. Contact mechanics and interfacial molecular force measurements confirm the dual role of vanadium (VIII) ions in forming this bilayer: VIII ions bridge the ligand sites to reinforce the protein bottom layer, and simultaneously anchor the end blocks of the designed ABA triblock hydrophilic polymers to form a hydrated, looping top layer. This VIII-enabled structure demonstrates remarkable load-bearing capacity and lubricating performance (i.e., friction coefficient μ on the order of 10-3 over 100 cycles under ∼10 MPa), while it also exhibits excellent resistance to biofouling in complex biological fluids. This work presents a useful strategy for integrating seemingly incompatible properties into ultrathin coatings, offering the potential for customizing multifunctional surfaces for micro-devices/machines toward bioengineering applications.

Engineered endothelium-mimicking antithrombotic surfaces via combination of nitric oxide-generation with fibrinolysis strategies

Thrombosis associated with implants can severely impact therapeutic outcomes and lead to increased morbidity and mortality. Thus, developing blood-contacting materials with superior anticoagulant properties is essential to prevent and mitigate device-related thrombosis. Herein, we propose a novel single-molecule multi-functional strategy for creating blood-compatible surfaces. The synthesized azide-modified Cu-DOTA-(Lys)3 molecule, which possesses both NO release and fibrinolysis functions, was immobilized on material surfaces via click chemistry. Due to the specificity, rapidity, and completeness of click chemistry, the firmly grafted Cu-DOTA-(Lys)3 endows the modified material with excellent antithrombotic properties of vascular endothelium and thrombolytic properties of fibrinolytic system. This surface effectively prevented thrombus formation in both in vitro and in vivo experiments, owing to the synergistic effect of anticoagulation and thrombolysis. Moreover, the modified material maintained its functional efficacy after one month of PBS immersion, demonstrating excellent stability. Overall, this single-molecule multifunctional strategy may become a promising surface engineering technique for blood-contacting materials.

Bio-Inspired Adaptive and Responsive Protein-Based Materials

In nature, the inherent adaptability and responsiveness of proteins play a crucial role in the survival and reproduction of organisms, enabling them to adjust to ever-changing environments. A comprehensive understanding of protein structure and function is essential for unraveling the complex biological adaptive processes, providing new insights for the design of protein-based materials in advanced fields. Recently, materials derived from proteins with specific properties and functions have been engineered. These protein-based materials, distinguished by their engineered adaptability and responsiveness, range from the nanoscale to the macroscale through meticulous control of protein structure. First, the review introduces the natural adaptability and responsiveness of proteins in organisms, encompassing biological adhesion and the responses of organisms to light, magnetic fields, and temperature. Next, it discusses the achievements in protein-engineered adaptability and adhesion through protein assembly and nanotechnology, emphasizing precise control over protein bioactivity. Finally, the review briefly addresses the application of protein engineering techniques and the self-assembly capabilities of proteins to achieve responsiveness in protein-based materials to humidity, light, magnetism, temperature, and other factors. We hope this review will foster a multidimensional understanding of protein adaptability and responsiveness, thereby advancing the interdisciplinary integration of biomedical science, materials science, and biotechnology.

Amyloid-Like Protein-Modified Carbon Nitride as a Bioinspired Material for Enhanced Photocatalytic CO2 Reduction

Modification of g-C3N4 with metal-free biomaterials through an environmentally friendly, low-energy, facile, and rapid single-step method is desired for the preparation of photocatalysts with efficient activity and high selectivity of CO2 reduction but remains a great challenge. Herein, we develop a phase-transitioned protein modification strategy for photocatalysts through superfast amyloid-like protein assembly on surfaces using a one-step sequential coating method. Metal-free carbon nitride/protein heterojunction composite photocatalysts (the phase-transitioned lysozyme (PTL), phase-transitioned bovine serum albumin (PTB), and phase-transitioned ovalbumin (PTO)-coated carbon nitride@SiO2 (CN@SiO2) and bioinspired carbon nitride hollow nanospheres (CN-HS) obtained by etching of CN@SiO2) are prepared using lysozyme, bovine serum albumin, and ovalbumin. The insulator-semiconductor heterojunctions formed at the protein-carbon nitride interface promote the migration and separation of photogenerated charges. The exposed hydrophobic alkyl and aryl groups of the surface-modified protein enable the formation of a CO2-aqueous solution-photocatalyst three-phase interface on the catalyst surface and the exposed -NH2 groups provide sites for CO2 adsorption, which effectively increases CO2 mass transfer and its adsorption as well as hydrophobicity, promoting CO2 reduction and inhibiting hydrogen production. Therefore, protein modification effectively improves the CO2 reduction activity and CO selectivity. For instance, compared to CN-HS, the CO yield of the PTL-modified CN-HS (1346.5 μmol g-1) increased by 24.5 times and the CO selectivity reached 90.5%. These findings represent a critical advancement in the surface modification of carbon nitride for CO2 reduction and the design of bioinspired materials for various applications.

Zwitterion-Conjugated Protein Coatings for Enhanced Antifouling in Complex Biofluids: Underlying Molecular Interaction Mechanisms

Biofouling can cause severe infections, device malfunctions, and failures in diagnostics and therapeutics. Proteins such as bovine serum albumin (BSA) have recently been used as coatings to resist biofouling because they combine surface anchoring and antifouling properties. However, their antifouling effectiveness will significantly deteriorate in complex biofluids with high salinity, limiting their practical applications. In this work, we developed a zwitterion-conjugated protein with enhanced antifouling capability by grafting zwitterionic 2-methacryloyloxyethyl phosphorylcholine (MPC) onto BSA protein via a click reaction. This conjugated protein can easily anchor on various substrates, both inorganic and organic, and exhibits efficient and broad-spectrum fouling resistance to metabolites, proteins, and complex biofluids. Even in the complex fetal bovine serum with higher salinity, the BSA@MPC coating can also maintain 99% fouling resistance robustly, over 6-fold superior to native BSA-coated surfaces in antifouling capability. Direct surface forces measurement reveals that such outstanding antifouling properties of conjugated protein BSA@MPC could be attributed to the stable hydration layer on its surface and the steric repulsion from the antipolyelectrolyte behavior of zwitterionic MPC polymer in the high-salinity environment. Our findings advance the development of protein-based functional materials and provide valuable insights for designing novel antifouling surfaces for marine, food, and bioengineering applications.

Antifouling and antimicrobial wearable electrochemical sweat sensors for accurate dopamine monitoring based on amyloid albumin composite hydrogels

Wearable electrochemical sweat sensors are potentially promising for health monitoring in a continuous and non-invasive mode with high sensitivity. However, due to the complexity of sweat composition and the growth of skin bacteria, the wearable sweat sensors may gradually lose their sensitivity or even fail over time. To deal with this issue, herein, we proposed a new strategy to construct wearable sweat sensors with antifouling and antimicrobial capabilities. Amyloid albumin hydrogels (ABSAG) were doped with two-dimensional (2D) nanomaterial MXene and CeO2 nanorods to obtain the antifouling and antimicrobial amyloid albumin composite hydrogels (ABSACG, CeO2/MXene/ABSAG), and the wearable sensors were prepared by modifying flexible screen-printed electrodes with the ABSACG. Within this sensing system, the hydrophilic ABSAG possesses strong hydration capability, and it can form a hydration layer on the electrode surface to resist biofouling in sweat. The 2D nanomaterial MXene dispersed in the hydrogel endows the hydrogel with good conductivity and electrocatalytic capability, while the doping of CeO2 nanorods further improves the electrocatalytic performance of the hydrogel and also provides excellent antimicrobial capability. The designed wearable electrochemical sensors based on the ABSACG demonstrated satisfying antifouling and antimicrobial abilities, and they were capable of detecting dopamine accurately in human sweat. It is expected that wearable sensors utilizing the antifouling and antimicrobial ABSACG may find practical applications in human body fluids analysis and health monitoring.

Reagent-free anti-fouling electrochemical immunosensor based on AL-BSA/AuNPs/PANI coating for the point-of-care detection of C-reactive protein in plasma and whole blood

Developing the portable CRP detection technologies that are suitable for point-of-care (POC) and primary care management is of utmost importance, and advancing the electrochemical immunosensors hold promise for POC implementation. Nevertheless, non-specific adsorption of numerous interfering proteins in complex biological media contaminates immunosensors, thereby restricting the reliability in detection efficacy. In this study, a three-dimensional flower-leaf shape amyloid bovine serum albumin/gold nanoparticles/polyaniline (AL-BSA/AuNPs/PANI) coating on the surface of the electrode was developed, which demonstrated strong anti-adsorption properties against bovine serum albumin, plasma, and cells. The immunosensor exhibited a good linear relationship to CRP response, featuring a detection limit of 0.09 μg/mL, consistent with clinical reference range. In addition, the CRP immunosensor demonstrated excellent specificity in other inflammation-related proteins and commendable anti-interference performance for CRP detection in plasma and whole blood tests. Importantly, by combining the development of a USB flash disk-type portable electrochemical workstation with a reagent-free mode, the developed CRP electrochemical immunosensor delivered ideal results in clinical samples. The anti-fouling performance, sensitivity and specificity of the immunosensor, as well as its flexible test modes in clinical samples, provide important scientific basis for developing POC detection technologies of vital biomarkers in complex biological media.

Aggregation-Disruption-Induced Multi-Scale Mediating Strategy for Anticoagulation in Blood-Contacting Devices

Minimally invasive blood-contacting interventional devices are increasingly used to treat cardiovascular diseases. However, the risk of device-related thrombosis remains a significant concern, particularly the formation of cycling thrombi, which pose life-threatening risks. To better understand the interactions between these devices and blood, the initial stages of coagulation contact activation on extrinsic surfaces are investigated. Direct force measurements reveals that activated contact factors stimulate the intrinsic coagulation pathway and promote surface crosslinking of fibrin. Furthermore, fibrin aggregation is disrupted by surface-grafted inhibitors, as confirmed by ex vivo coagulation tests. An engineered serum protein with zwitterion grafts to resist the deposition of biological species such as fibrin, platelets, and red blood cells is also developed. Simultaneously, a protease inhibitor-based coacervate is incorporated into the coating to inhibit the intrinsic pathway effectively. The loaded coacervate can be released and reloaded through modulation of catechol-amine interactions, facilitating material regeneration. The strategy offers a novel multi-scale mediation strategy that simultaneously inhibits nanoscale coagulation factors and resists microscale thrombus aggregation, providing a long-term solution for anticoagulation in blood-contacting devices.

Robust Chiral Metal-Organic Framework Coatings for Self-Activating and Sustainable Biofouling Mitigation

Surface coatings are designed to mitigate pervasive biofouling herald, a new era of surface protection in complex biological environments. However, existing strategies are plagued by persistent and recurrent biofilm attachment, despite the use of bactericidal agents. Herein, a chiral metal-organic framework (MOF)-based coating with conformal microstructures to enable a new anti-biofouling mode that involves spontaneous biofilm disassembly followed by bacterial eradication is developed. A facile and universal metal-polyphenol network (MPN) is designed to robustly anchor the MOF nanoarmor of biocidal Cu2+ ions and anti-biofilm d-amino acid ligands to a variety of substrates across different material categories and surface topologies. Incorporating a diverse array of chiral amino acids endows the resultant coatings with widespread signals for biofilm dispersal, facilitating copper-catalyzed chemodynamic reactions and inherent mechano-bactericidal activities. This synergistic mechanism yields unprecedented anti-biofouling efficacy elucidated by RNA-sequencing transcriptomics analysis, enhancing broad-spectrum antibacterial activities, preventing biofilm formation, and destroying mature biofilms. Additionally, the chelation-directed amorphous/crystalline coatings can activate photoluminescent properties to inhibit the settlement of microalgae biofilms. This study provides a distinctive perspective on chirality-enhanced antimicrobial behaviors and pioneers a rational pathway toward developing next-generation anti-biofouling coatings for diverse applications.

Biomimetic Porous MXene Antibacterial Adsorbents with Enhanced Toxins Trapping Ability for Hemoperfusion

2D transition metal carbides and nitrides, i.e., MXene, are recently attracting wide attentions and presenting competitive performances as adsorbents used in hemoperfusion. Nonetheless, the nonporous texture and easily restacking feature limit the efficient adsorption of toxin molecules inside MXene and between layers. To circumvent this concern, here a plerogyra sinuosa biomimetic porous titanium carbide MXene (P-Ti3C2) is reported. The hollow and hierarchically porous structure with large surface area benefits the maximum access of toxins as well as trapping them inside the spherical cavity. The cambered surface of P-Ti3C2 prevents layers restacking, thus affording better interlaminar adsorption. In addition to enhanced toxin removal ability, the P-Ti3C2 is found to selectively adsorb more middle and large toxin molecules than small toxin molecules. It possibly originates from the rich Ti-deficient vacancies in the P-MXene lattice that increases the affinity with middle/large toxin molecules. Also, the vacancies as active sites facilitate the production of reactive oxygen under NIR irradiation to promote the photodynamic antibacterial performance. Then, the versatility of P-MXene is validated by extension to niobium carbide (P-Nb2C). And the simulated hemoperfusion proves the practicability of the P-MXene as polymeric adhesives-free adsorbents to eliminate the broad-spectrum toxins.

A bifunctional lactoferrin-derived amyloid coating prevents bacterial adhesion and occludes dentinal tubules via deep remineralization

Dentin hypersensitivity (DH) manifests as sharp and uncomfortable pain due to the exposure of dentinal tubules (DTs) following the erosion of tooth enamel. Desensitizing agents commonly used in clinical practice have limitations such as limited depth of penetration, slow remineralization and no antimicrobial properties. To alleviate these challenges, our study designed a lactoferrin-derived amyloid nanofilm (PTLF nanofilm) inspired by the saliva-acquired membrane (SAP). The nanofilm utilises Tris(2-carboxyethyl)phosphine (TCEP) to disrupt the disulfide bonds of lactoferrin (LF) under physiological conditions. The PTLF nanofilm modifies surfaces across various substrates and effectively prevents the early and stable adhesion of cariogenic bacteria, such as Streptococcus mutans and Lactobacillus acidophilus. Simultaneously, it adheres rapidly and securely to demineralized dentin surfaces, facilitating in-situ remineralization of HAP through a simple immersion process. This leads to the formation of a remineralized layer resembling natural dentin, with an occlusion depth of dentinal tubules exceeding 80 µm after three days. The in vivo and vitro results confirm that the PTLF nanofilm possesses good biocompatibility and its ability to exert simultaneous antimicrobial effects and dentin remineralization. Accordingly, this innovative bifunctional PTLF amyloid coating offers promising prospects for the management of DH-related conditions. STATEMENT OF SIGNIFICANCE.

Preparation and Formation Mechanism Study of Antibiofilm Coating Based on Phase Transition of Glutenin

The surface of food processing equipment is easily affected by biofilm-forming bacteria, leading to cross-contamination and food safety hazards. The critical issue is how to endow the surface of contact materials with antibacterial and antibiofilm abilities. A sustainable, stable, and antibiofilm coating was prepared by phase transition of glutenin. The disulfide bonds in glutenin were reduced by tris(2-carboxyethyl)phosphine, triggering the phase transition of glutenin. Hydrophobic interactions and intermolecular disulfide bonds may be the primary forces. Furthermore, the phase-transited products formed a nanoscale coating on the surface of stainless steel and glass under their own adhesion force and gravity. The coating exhibited good stability in harsh environments. More importantly, after 3 h of direct contact, the colony of Escherichia coli and Staphylococcus aureus decreased by one logarithm. The amount of biofilm was observed to be significantly decreased through optical microscopy and scanning electron microscopy. This article provides a foundational module for developing novel coatings.

An antifouling supramolecular polymer ophthalmic ointment alleviates symblepharon in rat alkali burn eyes

Symblepharon is an adverse ocular disease resulting in ocular discomfort and impaired vision, severely dragging down a patient's quality of life. Due to the specificity of the ocular surface, the retention time of drugs on it is short, leading to limited therapeutic effects for ocular diseases. Therefore, it is imperative to design a novel drug delivery system, which can not only prolong the retention time of a drug but also play an anti-fibrosis role in symblepharon. Herein, an antifouling supramolecular polymer ophthalmic ointment consisting of poly(N-acryloyl alaninamide) (PNAAA), vitamin C (VitC) and levofloxacin (Levo) was developed (termed PNAVL ophthalmic ointment), which acted as a mucoadhesive and long-acting ocular delivery system. This antifouling PNAVL ophthalmic ointment improved the retention time of VitC and Levo, and simultaneously provided anti-inflammation and anti-fibrosis effects for mitigating symblepharon after ocular alkali burn injury.

3D porous conductive matrix based on phase-transited BSA and covalent coupling-stabilized transition ZnS-CNT for antifouling and on-site detection of nitrite in soil

Nitrite plays a critical role in a variety of nitrification and denitrification processes in the nitrogen cycle. Due to the high surface energy, tendency to aggregate, and poor conductivity, current nitrite ZnS-based sensing platform could not meet the need of on-site nitrite detection in smart agriculture. In order to address these issues, the carboxylated carbon nanotube (CNT) was introduced to reduce the surface energy and prevented aggregation of ZnS, while ZnS-carboxylated CNT (ZnS-CNT) composite also provided excellent electrochemical conductivity. Furthermore, the introduction of phase transition BSA (PTB) created a three-dimensional porous conductive matrix without interfering with the mass transfer process of nitrite. The resulting sensing platform exhibited a linear detection range of 10 nM to 0.4 mM for nitrite, with a detection limit of 0.73 nM. And this sensing platform had the excellent antifouling ability to direct detection nitrite in real soil suspension. In addition, the sensing platform demonstrated remarkable resistance to interferences from pH variations, microbial presence, and organic pollutants that usually present in soil environment. Therefore, on-site detection of nitrite ions in soil environment was realized no needing complex pretreatments.

Extracellular Matrix-Mimetic Intrinsic Versatile Coating Derived from Marine Adhesive Protein Promotes Diabetic Wound Healing through Regulating the Microenvironment

The management of diabetic wound healing remains a severe clinical challenge due to the complicated wound microenvironments, including abnormal immune regulation, excessive reactive oxygen species (ROS), and repeated bacterial infections. Herein, we report an extracellular matrix (ECM)-mimetic coating derived from scallop byssal protein (Sbp9Δ), which can be assembled in situ within 30 min under the trigger of Ca2+ driven by strong coordination interaction. The biocompatible Sbp9Δ coating and genetically programmable LL37-fused coating exhibit outstanding antioxidant, antibacterial, and immune regulatory properties in vitro. Proof-of-concept applications demonstrate that the coating can reliably promote wound healing in animal models, including diabetic mice and rabbits, ex vivo human skins, and Staphylococcus aureus-infected diabetic mice. In-depth mechanism investigation indicates that improved wound microenvironments accelerated wound repair, including alleviated bacterial infection, lessened inflammation, appearance of abundant M2-type macrophages, removal of ROS, promoted angiogenesis, and re-epithelialization. Collectively, our investigation provides an in situ, convenient, and effective approach for diabetic wound repair.

Active Dual-Protein Coating Assisted by Stepwise Protein-Protein Interactions Assembly Reduces Thrombosis and Infection

Universal protein coatings have recently gained wide interest in medical applications due to their biocompatibility and ease of fabrication. However, the challenge persists in protein activity preservation, significantly complicating the functional design of these coatings. Herein, an active dual-protein surface engineering strategy assisted by a facile stepwise protein-protein interactions assembly (SPPIA) method for catheters to reduce clot formation and infection is proposed. This strategy is realized first by the partial oxidation of bovine serum albumin (BSA) and lysozyme (LZM) for creating stable nucleation platforms via hydrophobic interaction, followed by the assembly of nonoxidized BSA (pI, the isoelectric point, ≈4.7) and LZM (pI ≈11) through electrostatic interaction owing to their opposite charge under neutral conditions. The SPPIA method effectively preserves the conformation and functionality of both BSA and LZM, thus endowing the resultant coating with potent antithrombotic and bactericidal properties. Furthermore, the stable nucleation platform ensures the adhesion and durability of the coating, resisting thrombosis and bacterial proliferation even after 15 days of PBS immersion. Overall, the SPPIA approach not only provides a new strategy for the fabrication of active protein coatings but also shows promise for the surface engineering technology of catheters.

Dual-Protection Inorganic-Protein Coating on Mg-Based Biomaterials through Tooth-Enamel-Inspired Biomineralization

Biocompatible magnesium alloys represent revolutionary implantable materials in dentistry and orthopedics but face challenges due to rapid biocorrosion, necessitating protective coatings to mitigate dysfunction. Directly integrating durable protective coatings onto Mg surfaces is challenging because of intrinsic low coating compactness. Herein, inspired by tooth enamel, a novel highly compact dual-protection inorganic-protein (inorganicPro) coating is in situ constructed on Mg surfaces through bovine serum albumin (BSA) protein-boosted reaction between sodium fluoride (NaF) and Mg substrates. The association of Mg ions and BSA establishes a local hydrophobic domain that lowers the formation enthalpy of NaMgF3 nanoparticles. This process generates finer nanoparticles that function as "bricks," facilitating denser packing, consequently reducing voidage inside coatings by over 50% and reinforcing mechanical durability. Moreover, the incorporation of BSA in and on the coatings plays two synergistic roles: 1) acting as "mortar" to seal residual cracks within coatings, thereby promoting coating compactness and tripling anticorrosion performance, and 2) mitigating fouling-accelerated biocorrosion in complex biosystems via tenfold resistance against biofoulant attachments, including biofluids, proteins, and metabolites. This innovative strategy, leveraging proteins to alter inorganic reactions, benefits the future coating design for Mg-based and other metallic materials with tailored anticorrosion and antifouling performances.

A label-free fluorescent magnetic dual-aptasensor based on aptamer allosteric regulation of β-lactoglobulin

We presented a label-free fluorescent biosensor based on magnetic dual-aptamer allosteric regulation of β-lactoglobulin (β-LG) detection. The bovine serum albumin (BSA) acted as the bridge to connect amino-modified magnetic beads and aptamer, which synthesized pyramid-type probes (MBAP) with high capture and reduced nonspecific adsorption. Moreover, the original aptamer was tailored and then designed as a bivalent aptamer to fabricate allosteric signal probes (ASP). The ASP can both specifically capture β-LG and output the fluorescence signal. The detection mechanism is as follows. The combination of the dual-aptamer and β-LG triggered the allosteric change, resulting in the release of SYBR Green (SG I) from the allosteric signal probe and change signals. This method exhibits a broad linear detection range from 10 ng/mL to 1 mg/mL and the limit of detection reaches as low as 8.06 ng/mL. This study provides a highly generalizable strategy for protein biomolecular detection via replacing different target aptamers.

On-The-Spot Sampling and Detection of Viral Particles on Solid Surfaces Using a Sponge Virus Sensor Incorporated with Finger-Press Fluid Release

This paper presents a sponge-based electrochemical sensor for rapid, on-site collection and analysis of infectious viruses on solid surfaces. The device utilizes a conducting porous sponge modified with graphene, graphene oxide, and specific antibodies. The sponge serves as a hydrophilic porous electrode capable of liquid collection and electrochemical measurements. The device operation involves spraying an aqueous solution on a target surface, swiping the misted surface using the sponge, discharging an electrolyte solution with a simple finger press, and performing in situ incubation and electrochemical measurements. By leveraging the water-absorbing ability of the biofunctionalized conducting sponge, the sensor can effectively collect and quantify virus particles from the surface. The portability of the device is enhanced by introducing a push-release feature that dispenses the liquid electrolyte from a miniature reservoir onto the sensor surface. This reservoir has sharp edges to rupture a liquid sealing film with a finger press. The ability of the device to sample and quantify viral particles is demonstrated by using influenza A virus as the model. The sensor provided a calculated limit of detection of 0.4 TCID50/mL for H1N1 virus, along with a practical concentration range from 1-106 TCID50/mL. Additionally, it achieves a 15% collection efficiency from single-run swiping on a tabletop surface. This versatile device allows for convenient on-site virus detection within minutes, eliminating the need for sample pretreatment and simplifying the entire sample collecting and measuring process. This device presents significant potential for rapid virus detection on solid surfaces.

Biomimetic Self-Maturation Mineralization System for Enamel Repair

Enamel repair is crucial for restoring tooth function and halting dental caries. However, contemporary research often overlooks the retention of organic residues within the repair layer, which hinders the growth of dense crystals and compromises the properties of the repaired enamel. During the maturation of natural enamel, the organic matrix undergoes enzymatic processing to facilitate further crystal growth, resulting in a highly mineralized tissue. Inspired by this process, a biomimetic self-maturation mineralization system is developed, comprising ribonucleic acid-stabilized amorphous calcium phosphate (RNA-ACP) and ribonuclease (RNase). The RNA-ACP induces initial mineralization in the form of epitaxial crystal growth, while the RNase present in saliva automatically triggers a biomimetic self-maturation process. The mechanistic study further indicates that RNA degradation prompts conformational rearrangement of the RNA-ACP, effectively excluding the organic matter introduced earlier. This exclusion process promotes lateral crystal growth, resulting in the generation of denser enamel-like apatite crystals that are devoid of organic residues. This strategy of eliminating organic residues from enamel crystals enhances the mechanical and physiochemical properties of the repaired enamel. The present study introduces a conceptual biomimetic mineralization strategy for effective enamel repair in clinical practice and offers potential insights into the mechanisms of biomineral formation.

Covalently grafted human serum albumin coating mitigates the foreign body response against silicone implants in mice

Implantable biomaterials and biosensors are integral components of modern medical systems but often encounter hindrances due to the foreign body response (FBR). Herein, we report an albumin coating strategy aimed at addressing this challenge. Using a facile and scalable silane coupling strategy, human serum albumin (HSA) is covalently grafted to the surface of polydimethylsiloxane (PDMS) implants. This covalently grafted albumin coating remains stable and resistant to displacement by other proteins. Notably, the PDMS with covalently grafted HSA strongly resists the fibrotic capsule formation following a 180-day subcutaneous implantation in C57BL/6 mice. Furthermore, the albumin coating led to reduced recruitment of macrophages and triggered a mild immune activation pattern. Exploration of albumin coatings sourced from various mammalian species has shown that only HSA exhibited a promising anti-FBR effect. The albumin coating method reported here holds the potential to improve and extend the function of silicone-based implants by mitigating the host responses to subcutaneously implanted biomaterials.

A Tough Monolithic-Integrated Triboelectric Bioplastic Enabled by Dynamic Covalent Chemistry

Electronic waste is a growing threat to the global environment and human health, raising particular concerns. Triboelectric devices synthesized from sustainable and degradable materials are a promising electronic alternative, but the mechanical mismatch at the interface between the polymer substrate and the electrodes remains unresolved in practical applications. This study uses the sulfhydryl silanization reaction and the chemical selectivity and site specificity of the thiol-disulfide exchange reaction in dynamic covalent chemistry to prepare a tough monolithic-integrated triboelectric bioplastic. The stress is dissipated by covalent bond adaptation to the interface interaction, which makes the polymer dielectric layer to the conductive layer have a good interface adhesion effect (220.55 kPa). The interfacial interlocking of the polymer substrate with the conductive layer gives the triboelectric bioplastic excellent tensile strength (87.4 MPa) and fracture toughness (33.3 MJ m-3). Even when subjected to a tension force of 10 000 times its weight, it still maintains a stable triboelectric output with no visible cracks. This study provides new insights into the design of reliable and environmentally friendly self-powered devices, which is significant for the development of flexible wearable electronics.

An insect sclerotization-inspired antifouling armor on biomedical devices combats thrombosis and embedding

Thrombus formation and tissue embedding significantly impair the clinical efficacy and retrievability of temporary interventional medical devices. Herein, we report an insect sclerotization-inspired antifouling armor for tailoring temporary interventional devices with durable resistance to protein adsorption and the following protein-mediated complications. By mimicking the phenol-polyamine chemistry assisted by phenol oxidases during sclerotization, we develop a facile one-step method to crosslink bovine serum albumin (BSA) with oxidized hydrocaffeic acid (HCA), resulting in a stable and universal BSA@HCA armor. Furthermore, the surface of the BSA@HCA armor, enriched with carboxyl groups, supports the secondary grafting of polyethylene glycol (PEG), further enhancing both its antifouling performance and durability. The synergy of robustly immobilized BSA and covalently grafted PEG provide potent resistance to the adhesion of proteins, platelets, and vascular cells in vitro. In ex vivo blood circulation experiment, the armored surface reduces thrombus formation by 95 %. Moreover, the antifouling armor retained over 60 % of its fouling resistance after 28 days of immersion in PBS. Overall, our armor engineering strategy presents a promising solution for enhancing the antifouling properties and clinical performance of temporary interventional medical devices.

Antifouling strategies for electrochemical sensing in complex biological media

Surface fouling poses a significant challenge that restricts the analytical performance of electrochemical sensors in both in vitro and in vivo applications. Biofouling resistance is paramount to guarantee the reliable operation of electrochemical sensors in complex biofluids (e.g., blood, serum, and urine). Seeking efficient strategies for surface fouling and establishing highly sensitive sensing platforms for applications in complex media have received increasing attention in the past. In this review, we provide a comprehensive overview of recent research efforts focused on antifouling electrochemical sensors. Initially, we present a detailed illustration of the concept about biofouling along with an exploration of four key antifouling mechanisms. Subsequently, we delve into the commonly employed antifouling strategies in the fabrication of electrochemical sensors. These encompass physical surface topography (micro/nanostructure coatings and filtration membranes) and chemical surface modifications (PEG and its derivatives, zwitterionic polymers, peptides, proteins, and various other antifouling materials). The progress in antifouling electrochemical sensors is proposed concerning the antifouling mechanisms as well as sensing capability assessments (e.g., sensitivity, stability, and practical application ability). Finally, we summarize the evolving trends in the field and highlight some key remaining limitations.

Protein-based bioactive coatings: from nanoarchitectonics to applications

Protein-based bioactive coatings have emerged as a versatile and promising strategy for enhancing the performance and biocompatibility of diverse biomedical materials and devices. Through surface modification, these coatings confer novel biofunctional attributes, rendering the material highly bioactive. Their widespread adoption across various domains in recent years underscores their importance. This review systematically elucidates the behavior of protein-based bioactive coatings in organisms and expounds on their underlying mechanisms. Furthermore, it highlights notable advancements in artificial synthesis methodologies and their functional applications in vitro. A focal point is the delineation of assembly strategies employed in crafting protein-based bioactive coatings, which provides a guide for their expansion and sustained implementation. Finally, the current trends, challenges, and future directions of protein-based bioactive coatings are discussed.

Synthesis and functionalization of scalable and versatile 2D protein films via amyloid-like aggregation

Two-dimensional (2D) protein films can be used to modify the properties of surfaces, and find applications predominantly in the fields of biomaterials, lithography, optics and electronics. However, it is difficult to produce scalable homogeneous and robust protein films with an easy, low-cost, green and efficient method. Further challenges include encapsulating and releasing functional building blocks in the film without inactivating them, and maintaining or improving the bioactivities of proteins used for the formation of the films. Here we detail the process to prepare large 2D protein films with user-defined features and structures via the amyloid-like aggregation of commonly synthesized proteins. These films can be synthesized at meter scales, have high interface adhesion, high functional expansibility and tunable functional properties, obtained by controlling the position of the disulfide bond breakage. For example, we can retain or even enhance the natural antibacterial, biomineralization and antifouling activity of proteins involved in film formation, and the properties can also be expanded through the physical blending or chemical grafting of additional functional blocks on the surface of the film. A 2D protein film can be prepared in ~3 h using four alternative coating techniques: immersion, transfer, hydrogel stamping and spraying. The characterization process of the film requires ~5 d. The procedure can be carried out by users with basic expertise in materials science.

Reagentless impedimetric immunosensor for monitoring of methotrexate in human blood serum using multiwalled carbon nanotube@polypyrrole/polytyramine film electrode

Ensuring effective monitoring of methotrexate (MTX) levels in the bloodstream of cancer patients undergoing high-dose methotrexate chemotherapy is crucial to prevent potentially harmful side effects. However, the absence of portable analytical devices suitable for point-of-care bedside monitoring has presented a significant obstacle to achieving real-time MTX monitoring. In this study, we developed an impedimetric immunosensor that doesn't require reagents for measuring MTX levels in undiluted human blood serum. This reagentless approach simplifies the assay process, enabling rapid and straightforward MTX quantification. The immunosensor transducer was fabricated by electrodepositing conductive network of porous multiwalled carbon nanotube@polypyrrole/polytyramine on screen-printed gold microchip electrode (SP-Au/MWCNT70@PPy-PTA). Polyclonal anti-MTX antibodies were immobilized on the film, acting as the immunorecognition element. Non-specific binding was prevented by blocking the transducer interface with denatured bovine serum albumin (dBSA) fibrils, resulting in SP-Au/MWCNT70@PPy-PTA/anti-MTXAb|dBSA film electrode. When MTX binds to the SP-Au/MWCNT70@PPy-PTA/anti-MTXAb|dBSA interface, the film conductance and electron transfer resistance changes. This conductivity attenuation allows for electrochemical impedimetric signal transduction without a redox-probe solution. The electrochemical impedance spectroscopy (EIS) results showed increased charge transfer resistance and phase angle as MTX concentrations increased. The SP-Au/MWCNT70@PPy-PTA/anti-MTXAb|dBSA demonstrated high sensitivity, with a linear response from 0.02 to 20.0 μM and a detection limit of 1.93 nM. The detection limit was 50 times lower than the intended safe level of MTX in human serum. The immunosensor exhibited minimal cross-reactivity with endogenous MTX analogs and serum proteins. The SP-Au/MWCNT70@PPy-PTA/anti-MTXAb|dBSA immunosensor presents a simple and rapid method for therapeutic drug monitoring compared to traditional immunoassay systems.

Antifouling modification for high-performance isolation of circulating tumor cells

Circulating tumor cells (CTCs), which shed from solid tumor tissue into blood circulatory system, have attracted wide attention as a biomarker in the early diagnosis and prognosis of cancer. Given their potential significance in clinics, many platforms have been developed to separate CTCs. However, the high-performance isolation of CTCs remains significant challenges including achieving the sensitivity and specificity necessary due to their extreme rarity and severe biofouling in blood, such as billions of background cells and various proteins. With the advancement of CTCs detection technologies in recent years, the highly efficient and highly specific detection platforms for CTCs have gradually been developed, resulting in improving CTC capture efficiency, purity and sensitivity. In this review, we systematically describe the current strategies with surface modifications by utilizing the antifouling property of polymer, peptide, protein and cell membrane for high-performance enrichment of CTCs. To wrap up, we discuss the substantial challenges facing by current technologies and the potential directions for future research and development.

Unraveling the Adhesion Behavior of Different Cell Lines on Biomimetic PEDOT Interfaces: The Role of Surface Morphology and Antifouling Properties

The poly(3,4-ethylenedioxythiophene) (PEDOT) interface, renowned for its biocompatibility and intrinsic conductivity, holds substantial potential in biosensing and cellular modulation. Through strategic functionalization, PEDOT derivatives can be adaptable for multifaceted applications. Notably, integrating phosphorylcholine (PC) groups into PEDOT, mimicking the hydrophilic headgroups from cell membranes, confers exceptional antifouling properties on the coating. This study systematically investigated biomolecule interactions with distinct forms of PEDOT, incorporating variations in surface modifications and structure. Zwitterionic PEDOT-PC was electropolymerized on smooth and nanostructured surfaces using various feeding ratios in electrolytes to finely control the antifouling properties of the interface. Precise electropolymerization conditions governed the attainment of smooth and nanostructured filamentous surfaces. The study employed a quartz crystal microbalance with dissipation (QCM-D) to assess protein binding behavior. Bovine serum albumin (BSA), lysozyme (LYZ), cytochrome c (cyt c), and fibronectin (FN) were used to evaluate their binding affinities for PEDOT films. FN, a pivotal extracellular matrix component, was included for connecting to cell adhesion behavior. Furthermore, the cellular adhesion behaviors on PEDOT interfaces were evaluated. Three cell lines─MG-63 osteosarcoma, HeLa cervical cancer, and fibroblast NIH/3T3 were examined. The presence of PC moieties significantly altered the adhesive response, including the number of attached cells, their morphologies, and nucleus shrinkage. MG-63 cells exhibited the highest tolerance for PC moieties. A feeding ratio of PEDOT-PC exceeding 70% resulted in cell apoptosis. This study contributes to understanding biomolecule adsorption on PEDOT surfaces of diverse morphologies and degrees of the antifouling moiety. Meanwhile, it also sheds light on the responses of various cell types.

Engineering Immunomodulatory Stents Using Zinc Ion-Lysozyme Nanoparticle Platform for Vascular Remodeling

Rapid endothelialization of cardiovascular materials can enhance the vascular remodeling performance. In this work, we developed a strategy for amyloid-like protein-assembly-mediated interfacial engineering to functionalize a biomimetic nanoparticle coating (BMC). Various groups (e.g., hydroxyl and carboxyl) on the BMC are responsible for chelating Zn2+ ions at the stent interface, similar to the glutathione peroxidase-like enzymes found in vivo. This design could reproduce the release of therapeutic nitric oxide gas (NO) and an aligned microenvironment nearly identical with that of natural vessels. In a rabbit abdominal aorta model, BMC-coated stents promoted vascular healing through rapid endothelialization and the inhibition of intimal hyperplasia in the placement sites at 4, 12, and 24 weeks. Additionally, better anticoagulant activity and immunomodulation in the BMC stents were also confirmed, and vascular healing was mainly dependent on cell signaling through the cyclic guanosine monophosphate-protein kinase G (cGMP-PKG) cascade. Overall, a metal-polypeptide-coated stent was developed on the basis of its detailed molecular mechanism of action in vascular remodeling.

Design of a Facile Antifouling Sensor Based on the Synergy between an Antibody and Phase-Transited BSA

Nonspecific adsorption has always been a critical challenge for sensor detection; thus, an efficient and facile approach for fabricating antifouling sensors is highly desirable. Here, we developed an antifouling coating on sensor surfaces, conveniently made with a simple drip of phase-transited BSA (PTB) followed by a modification with a peanut allergen antibody, which unexpectedly provides synergistic antifouling properties in sensors. Atomic force microscopy and scanning electron microscopy were used to evaluate the surface evenness. Optimizations in terms of PTB modification time and concentrations were performed using surface plasmon resonance by measuring protein resistance capabilities. Compared to bare Au surfaces, the PTB-modified surfaces exhibited low adsorption against BSA (<10 ng/cm2) and good resistance against lysozyme (Lyz). After immobilizing antibodies, the antifouling performance of the sensor coatings had an obvious enhancement, with almost no BSA adsorption and low lysozyme adsorption. The target recognition was also analyzed to verify the good sensing performance of the antifouling sensor. This understanding of antibody synergy provides suggestions for the development of antifouling sensors.

Interface-mediated protein aggregation

The aggregation of proteins at interfaces has significant roles and can also lead to dysfunction of different physiological processes. The interfacial effects on the assembly and aggregation of biopolymers are not only crucial for a comprehensive understanding of protein biological functions, but also hold great potential for advancing the state-of-the-art applications of biopolymer materials. Recently, there has been remarkable progress in a collaborative context, as we strive to gain control over complex interfacial assembly structures of biopolymers. These biopolymer structures range from the nanoscale to mesoscale and even macroscale, and are attained through the rational design of interactions between biological building blocks and surfaces/interfaces. This review spotlights the recent advancements in interface-mediated assembly and properties of biopolymer materials. Initially, we introduce the solid-liquid interface (SIL)-mediated biopolymer assembly that includes the inorganic crystalline template effect and protein self-adoptive deposition through phase transition. Next, we display the advancement of biopolymer assembly instigated by the air-water interface (AWI) that acts as an energy conversion station. Lastly, we discuss succinctly the assembly of biopolymers at the liquid-liquid interface (LLI) along with their applications. It is our hope that this overview will stimulate the integration and progression of the science of interfacial assembled biopolymer materials and surfaces/interfaces.

Bioinspired engineered proteins enable universal anchoring strategy for surface functionalization

HYPOTHESIS

Conventional coating strategies and materials for bio-applications with protective, diagnostic, and therapeutic functions are commonly limited by their arduous preparation processes and lack of on-demand functionalities. Herein, inspired by the 'root-leaf' structure of grass, a series of novel polyacrylate-conjugated proteins can be engineered with sticky bovine serum albumin (BSA) protein as a 'root' anchoring layer and a multifunctional polyacrylate as a 'leaf' functional layer for the facile coating procedure and versatile surface functionalities.

EXPERIMENTS

The engineered proteins were synthesized based on click chemistry, where the 'root' layer can universally anchor onto both organic and inorganic substrates through a facile dip/spraying method with excellent stability in harsh solution conditions, thanks to its multiple adaptive molecular interactions with substrates that further elucidated by molecular force measurements between the 'root' BSA protein and substrates. The 'leaf' conjugated-polyacrylates imparted coatings with versatile on-demand functionalities, such as resistance to over 99% biofouling in complex biofluids, pH-responsive performance, and robust adhesion with various nanomaterials.

FINDINGS

By synergistically leveraging the universal anchoring capabilities of BSA with the versatile physicochemical properties of polyacrylates, this study introduces a promising and facile strategy for imparting novel functionalities to a myriad of surfaces through engineering natural proteins and biomaterials for biotechnical and nanotechnical applications.

A Remineralizing and Antibacterial Coating for Arresting Caries

Dental caries is a dynamic disease induced by the unbalance between demineralization of dental hard tissues caused by biofilm and remineralization of them; however, although various effective remineralization methods have been well documented, it is a challenge to reestablish the balance by enhancing remineralization alone while ignoring the antibacterial therapy. Therefore, the integration of remineralizing and antibacterial technologies offers a promising strategy to halt natural caries progression in clinical practice. Here, the conception of interrupting dental caries (IDC) was proposed based on the development of dual-functional coating with remineralizing and antibacterial properties. In this study, bovine serum albumin (BSA) loaded octenidine (OCT) successfully to form a BSA-OCT composite. Subsequently, through fast amyloid-like aggregation, the phase-transited BSA-OCT (PTB-OCT) coating can be covered on teeth, resin composite, or sealant surfaces in 30 min by a simple smearing process. The PTB-OCT coating showed satisfactory effects in promoting the remineralization of demineralized enamel and dentin in vitro. Moreover, this coating also exerted significant acid-resistance stability and anti-biofilm properties. Equally importantly, this coating exhibited promising abilities in reducing the microleakage between the tooth and resin composite in vitro and preventing primary and secondary caries in vivo. In conclusion, this novel dual-functional PTB-OCT coating could reestablish the balance between demineralization and remineralization in the process of caries, thereby potentially preventing or arresting caries.