Advanced Nanocellulose-Based Composites for Flexible Functional Energy Storage Devices

Stable loading of MOF-derived carbon skeleton encapsulated Ni and BiOBr on carbonized cellulose fibers for fabricating high-performance and recyclable photocatalytic paper

The highly dispersed small-size metal co-catalysts can effectively improve the photocatalytic efficiency of semiconductor photocatalysts by separating photogenerated electrons and enriching active sites. However, this system tends to aggregate in the absence of carrier, resulting in the decrease of active sites. Here, MOF-derived carbon skeleton (MDCS) encapsulated Ni nanoparticles (Ni@MDCS) and BiOBr was loaded onto carbonized cellulose fibers (CCF) with the help of polydopamine (PDA) to construct high-performance and recyclable photocatalytic paper for photocatalytic degradation of organic dyes in water. The characterization results showed that MDCS promoted good dispersion of Ni nanoparticles and provided sufficient active sites. And Ni@MDCS as a co-catalyst accelerated the separation of photogenerated carriers in BiOBr. The PDA improved the loading state of Ni@MDCS on CCF and converted into N-doped C in the carbonization process for further increasing the transfer efficiency of photogenerated electrons. In the composite paper, the stable loading of Ni@MDCS/BiOBr hybrid on CCF improved the dispersion and reusability of photocatalyst. The degradation rate of rhodamine B on CCF/PDA-C/Ni@MDCS/BiOBr paper was as high as 94.6 % after 60 min visible light irradiation, which was about 2.5 times higher than that of CCF/BiOBr paper. During 10 cycles, CCF/PDA-C/Ni@MDCS/BiOBr paper maintained high photocatalytic efficiency and good structural stability. This study provides a new way for developing high-performance and recyclable photocatalytic paper.

Nano/micro flexible fiber and paper-based advanced functional packaging materials

Recently, fiber-based and functional paper food packaging has garnered significant attention for its versatility, excellent performance, and potential to provide sustainable solutions to the food packaging industry. Fiber-based food packaging is characterized by its large surface area, adjustable porosity and customizability, while functional paper-based food packaging typically exhibits good mechanical strength and barrier properties. This review summarizes the latest research progress on food packaging based on fibers and functional paper. Firstly, the raw materials used for preparing fiber and functional paper, along with their physical and chemical properties and roles in food packaging, were discussed. Subsequently, the latest advancements in the application of fiber and paper materials in food packaging were introduced. This paper also discusses future research directions and potential areas for improvement in fiber and functional paper food packaging to further enhance their effectiveness in ensuring food safety, quality, and sustainability.

Dual cross-linked cellulose-based hydrogel for dendrites-inhibited flexible zinc-ion energy storage devices with ultra-long cycles and high energy density

Hydrogel electrolytes, renowned for their mechanical robustness and versatility, are crucial in ensuring stable energy output in flexible energy storage devices. This work presents a dual cross-linked cellulose-based hydrogel electrolyte with chemical cross-linking from covalent bonding and physical cross-linking from hydrogen bonding. This electrolyte demonstrated outstanding mechanical strength and porous structure with abundant hydroxyl groups, which facilitates the migration of Zn2+ and suppresses the formation of undesirable zinc dendrite, thereby enhancing the ion conductivity (18.46 ± 0.39 mS cm-1 at room temperature) and extending electrochemical stability window (0-2.23 V). Zn||Zn symmetric cells based on this electrolyte demonstrated stable stripping/plating cycles of 3000 h at a current density of 1 mA cm-2. Furthermore, the corresponding flexible zinc-ion hybrid capacitor retains a 90.3 % capacity over 100,000 cycles at 10 A g-1, while remaining functional across various folding angles. Hence, this biomass-derived hydrogel electrolyte holds promise for flexible energy storage device applications.

Lignocellulosic biomass-derived functional nanocellulose for food-related applications: A review

In recent years, nanocellulose (NC) has gained significant attention due to its remarkable properties, such as adjustable surface chemistry, extraordinary biological properties, low toxicity and low density. This review summarizes the preparation of NC derived from lignocellulosic biomass (LCB), including cellulose nanofibrils (CNF), cellulose nanocrystals (CNC), and lignin-containing cellulose nanofibrils (LCNF). It focuses on examining the impact of non-cellulosic components such as lignin and hemicellulose on the functionality of NC. Additionally, various surface modification strategies of NC were discussed, including esterification, etherification and silylation. The review also emphasizes the progress of NC application in areas such as Pickering emulsions, food packaging materials, food additives, and hydrogels. Finally, the prospects for producing NC from LCB and its application in food-related fields are examined. This work aims to demonstrate the effective benefits of preparing NC from lignocellulosic biomass and its potential application in the food industry.

All-Cellulose-based flexible Zinc-Ion battery enabled by waste pomelo peel

Aqueous zinc-ion batteries are attracting extensive attention due to the long-term service life and credible safety as well as the superior price performance between the low cost of manufacture and high energy density. The fabrication of inexpensive, high-performance flexible solid-state zinc-ion batteries, thus, are urgently need for the blooming wearable electronics. Herein, as a proof-of-concept study of waste into wealth, cellulose flakes derived from waste pomelo peel are utilized as the substrate for electrodes and hydrogel electrolytes into a flexible rocking-chair zinc-ion battery. The unique sandwich-type structure holding the flake-like cellulose substrate and linear carbon nanotubes endows the flexible cathode and anode with fast ion and electron transportation. The obtained cellulose-based hydrogel electrolytes on account of special affinity with aqueous ZnSO4 electrolyte output an excellent ionic conductivity. The assembled flexible rocking-chair zinc-ion battery benefitting from the synergistic effect of sandwich-type electrodes and cellulose-based hydrogel electrolytes demonstrates outstanding electrochemical performance and mechanical properties. This work not only puts up an effective roadmap for flexible battery devices, but also reveals the great potential of waste biomass materials in energy storage applications.

Pickering Foam Stabilized by Diacylglycerol-Based Solid Lipid Nanoparticles: Effect of Protein Modification

Pickering foams have great potential for applications in aerated foods, but their foaming ability and physical stability are still far from satisfactory. Herein, solid lipid particles (SLNs) were fabricated by using diacylglycerol of varying acyl chain lengths with modification by a protein. The SLNs showed different crystal polymorphisms and air-water interfacial activity. C14-DAG SLN with a contact angle ∼ 79° formed aqueous foam with supreme stability and high plasticity. Whey protein isolate and sodium caseinate (0.1 wt %) considerably enhanced the foamability and interfacial activity of SLNs and promoted the packing of particles at the bubble surface. However, high protein concentration caused foam destruction due to the competitive adsorption effect. β-sheet increased in protein after adsorption and changed the polymorphism and thermodynamic properties of SLN. The foam collapsing behaviors varied in the presence of protein. The results gave insights into fabricating ultrastable aqueous foams by using high-melting DAG particles. The obtained foams demonstrated good temperature sensitivity and plasticity, which showed promising application prospects in the food and cosmetic fields.

Suppressed Dissolution of Fluorine-Rich SEI Enables Highly Reversible Zinc Metal Anode for Stable Aqueous Zinc-Ion Batteries

The instability of the solid electrolyte interface (SEI) is a critical challenge for the zinc metal anodes, leading to an erratic electrode/electrolyte interface and hydrogen evolution reaction (HER), ultimately resulting in anode failure. This study uncovers that the fluorine species dissolution is the root cause of SEI instability. To effectively suppress the F- dissolution, an introduction of a low-polarity molecule, 1,4-thioxane (TX), is proposed, which reinforces the stability of the fluorine-rich SEI. Moreover, the TX molecule has a strong affinity for coordinating with Zn2+ and adsorbing at the electrode/electrolyte interface, thereby diminishing the activity of local water and consequently impeding SEI dissolution. The robust fluorine-rich SEI layer promotes the high durability of the zinc anode in repeated plating/stripping cycles, while concurrently suppressing HER and enhancing Coulombic efficiency. Notably, the symmetric cell with TX demonstrates exceptional electrochemical performance, sustaining over 500 hours at 20 mA cm-2 with 10 mAh cm-2. Furthermore, the Zn||KVOH full cell exhibits excellent capacity retention, averaging 6.8 mAh cm-2 with 98 % retention after 400 cycles, even at high loading with a lean electrolyte. This work offers a novel perspective on SEI dissolution as a key factor in anode failure, providing valuable insights for the electrolyte design in energy storage devices.

Photopolymerization Approach to Advanced Polymer Composites: Integration of Surface-Modified Nanofillers for Enhanced Properties

The incorporation of functionalized nanofillers into polymers via photopolymerization approach has gained significant attention in recent years due to the unique properties of the resulting composite materials. Surface modification of nanofillers plays a crucial role in their compatibility and polymerization behavior within the polymer matrix during photopolymerization. This review focuses on the recent developments in surface modification of various nanofillers, enabling their integration into polymer systems through photopolymerization. The review discusses the key aspects of surface modification of nanofillers, including the selection of suitable surface modifiers, such as photoinitiators and polymerizable groups, as well as the optimization of modification conditions to achieve desired surface properties. The influence of surface modification on the interfacial interactions between nanofillers and the polymer matrix is also explored, as it directly impacts the final properties of the nanocomposites. Furthermore, the review highlights the applications of nanocomposites prepared by photopolymerization, such as sensors, gas separation membranes, purification systems, optical devices, and biomedical materials. By providing a comprehensive overview of the surface modification strategies and their impact on the photopolymerization process and the resulting nanocomposite properties, this review aims to inspire new research directions and innovative ideas in the development of high-performance polymer nanocomposites for diverse applications.

Strong Yet Tough Transparent Paper with Superb Foldability

Transparent paper manufactured from wood fibers is emerging as a promising, cost-effective, and carbon-neutral alternatives to plastics. However, fully exploring their mechanical properties is one of the most pressing challenges. In this work, a strong yet tough transparent paper with superior folding endurance is prepared by rationally altering the native fiber structure. Microwave-assisted choline chloride/lactic acid deep eutectic solvent (DES) pulping is first utilized to isolate wood fibers from spruce wood. During this process, the S1 layer within the fibers is partially disrupted, forming protruding microfibrils that play a crucial role in enhancing cellulose accessibility. Subsequently, carboxymethylation treatment is applied to yield uniformly swollen carboxymethylated wood fibers (CM fibers), which improves the interaction between CM fibers during papermaking. The as-prepared transparent paper not only shows a 90% light transmittance (550 nm) but also exhibits impressive mechanical properties, including a folding endurance of over 26 000, a tensile strength of 248.4 MPa, and a toughness of 15.6 MJ m-3. This work provides a promising route for manufacturing transparent paper with superior mechanical properties from wood fibers and can extend their use in areas normally dominated by high-performance nonrenewable plastics.

Flexible Supercapacitor with Wide Electrochemical Stable Window Based on Hydrogel Electrolyte

Hydrogel electrolyte can endow supercapacitors with excellent flexibility, which has developed rapidly in recent years. However, the water-rich structures of hydrogel electrolyte are easy to freeze at subfreezing and dry at high temperatures, which will affect its energy storage characteristics. The low energy density of micro supercapacitors also hinders their development. Herein, a strategy is proposed to reduce the free water activity in the hydrogel to improve the operating voltage and the energy density of the device, which is achieved through the synergistic effect of the hydrogel skeleton, N, N'-dimethylformamide (DMF), NaClO4 and water. High concentrations of DMF and NaClO4 are introduced into sodium alginate/polyacrylamide (SA/PAAM) hydrogel through solvent exchange to obtain SA/PAAM/DMF/NaClO4 hydrogel electrolyte, which exhibited a high ionic conductivity of 82.1 mS cm-1, a high breaking strength of 563.2 kPa, and a wide voltage stability window of 3.5 V. The supercapacitor devices are assembled by the process of direct adhesion of the hydrogel electrolyte and  laser induced graphene (LIG). The micro-supercapacitor exhibited an operating voltage of 2.0 V, with a specific capacitance of 2.41 mF cm-2 and a high energy density of 1.34 µWh cm-2, and it also exhibit a high cycle stability, good flexibility, and integration performance.

Flexible electrochemical energy storage devices and related applications: recent progress and challenges

Given the escalating demand for wearable electronics, there is an urgent need to explore cost-effective and environmentally friendly flexible energy storage devices with exceptional electrochemical properties. However, the existing types of flexible energy storage devices encounter challenges in effectively integrating mechanical and electrochemical performances. This review is intended to provide strategies for the design of components in flexible energy storage devices (electrode materials, gel electrolytes, and separators) with the aim of developing energy storage systems with excellent performance and deformability. Firstly, a concise overview is provided on the structural characteristics and properties of carbon-based materials and conductive polymer materials utilized in flexible energy storage devices. Secondly, the fabrication process and strategies for optimizing their structures are summarized. Subsequently, a comprehensive review is presented regarding the applications of carbon-based materials and conductive polymer materials in various fields of flexible energy storage, such as supercapacitors, lithium-ion batteries, and zinc-ion batteries. Finally, the challenges and future directions for next-generation flexible energy storage systems are proposed.

Design and Synthesis of a Robust and Multifunctional Superhydrophobic Coating with a Three-Dimensional Network Structure on a Paper-Based Material

A fundamental challenge in artificial superhydrophobic papers is their poor resistance to mechanical abrasion, which limits their practical application in different fields. Herein, a robust and multifunctional superhydrophobic paper is successfully fabricated via a facile spraying method by combining silver nanowires and fluorinated titania nanoparticles through a common paper sizing agent (alkyl ketene dimer) onto paper. It is shown that the surface of the paper-based material presents a three-dimensional network structure due to the cross-linking of silver nanowires with a high aspect ratio. Further hydrophilic and hydrophobic performance test results show that it exhibits exceptional water repellency, with a desirable static contact angle of 165° and roll-off angle of 6.2°. The superhydrophobic paper showcases excellent mechanical durability and maintains its superhydrophobicity even after enduring 130 linear sandpaper abrasion cycles or high-velocity water jetting impact benefited from interfacial van der Waals and hydrogen bonding. Simultaneously, the robust superhydrophobic surface can effectively prevent the penetration of acid or alkali solutions, as well as UV light, resulting in excellent chemical stability. Additionally, the superhydrophobic paper offers supplementary features such as self-cleaning, electrical conductivity, and antibacterial capability. Further development of this strategy paves a way toward next-generation superhydrophobic paper composed of nanostructures and characterized by multiple (or additional) functionalities.

Challenges and Breakthroughs in Enhancing Temperature Tolerance of Sodium-Ion Batteries

Lithium-based batteries (LBBs) have been highly researched and recognized as a mature electrochemical energy storage (EES) system in recent years. However, their stability and effectiveness are primarily confined to room temperature conditions. At temperatures significantly below 0 °C or above 60 °C, LBBs experience substantial performance degradation. Under such challenging extreme contexts, sodium-ion batteries (SIBs) emerge as a promising complementary technology, distinguished by their fast dynamics at low-temperature regions and superior safety under elevated temperatures. Notably, developing SIBs suitable for wide-temperature usage still presents significant challenges, particularly for specific applications such as electric vehicles, renewable energy storage, and deep-space/polar explorations, which requires a thorough understanding of how SIBs perform under different temperature conditions. By reviewing the development of wide-temperature SIBs, the influence of temperature on the parameters related to battery performance, such as reaction constant, charge transfer resistance, etc., is systematically and comprehensively analyzed. The review emphasizes challenges encountered by SIBs in both low and high temperatures while exploring recent advancements in SIB materials, specifically focusing on strategies to enhance battery performance across diverse temperature ranges. Overall, insights gained from these studies will drive the development of SIBs that can handle the challenges posed by diverse and harsh climates.

Carbon-based single-atom catalysts derived from biomass: Fabrication and application

Single-atom catalysts (SACs) with active metals dispersed atomically have shown great potential in heterogeneous catalysis due to the high atomic utilization and superior selectivity/stability. Synthesis of SACs using carbon-neutral biomass and its components as the feedstocks provides a promising strategy to realize the sustainable and cost-effective SACs preparation as well as the valorization of underused biomass resources. Herein, we begin by describing the general background and status quo of carbon-based SACs derived from biomass. A detailed enumeration of the common biomass feedstocks (e.g., lignin, cellulose, chitosan, etc.) for the SACs preparation is then offered. The interactions between metal atoms and biomass-derived carbon carriers are summarized to give general rules on how to stabilize the atomic metal centers and rationalize porous carbon structures. Furthermore, the widespread adoption of catalysts in diverse domains (e.g., chemocatalysis, electrocatalysis and photocatalysis, etc.) is comprehensively introduced. The structure-property relationships and the underlying catalytic mechanisms are also addressed, including the influences of metal sites on the activity and stability, and the impact of the unique structure of single-atom centers modulated by metal/biomass feedstocks interactions on catalytic activity and selectivity. Finally, we end this review with a look into the remaining challenges and future perspectives of biomass-based SACs. We expect to shed some light on the forthcoming research of carbon-based SACs derived from biomass, manifestly stimulating the development in this emerging research area.

One-pot extraction of nanocellulose from raw durian husk fiber using carboxylic acid-based deep eutectic solvent with in situ ultrasound assistance

Nanocellulose (CNF) has emerged as a promising alternative to synthetic petroleum-based polymers, but the conventional preparation process involves multiple tedious steps, heavily dependent on chemical input, and proves cost-inefficient. This study presented an, in situ ultrasound-assisted extraction using deep eutectic solvent (DES) based on choline chloride and oxalic acid for more facile production of CNF from raw durian husk fibers. FESEM analysis confirmed the successful extraction of web-like nanofibril structure with width size ranging from 18 to 26 nm. Chemical composition analysis and FTIR revealed the selective removal of lignin and hemicellulose from the raw fiber. As compared to post-ultrasound treatment, in situ ultrasound-assisted extraction consistently outperforms, yielding a higher CNF yield with finer fiber width and significantly reduced lignin content. Integrating this eco-friendly in situ ultrasonication-assisted one-pot extraction method with a 7.5 min interval yielded the highest CNF yield of 58.22 % with minimal lignin content. The superior delignification ability achieved through the proposed in situ ultrasound-assisted protocol surpasses the individual efficacy of DES and ultrasonication processes, neither of which yielded CNF in our experimental setup. This single-step fabrication process significantly reduces chemical usage and streamlines the production steps yielding web-structured CNF that is ideal for sustainable application in membrane and separator.

Synthesis and characterization of polyaniline-based composites using cellulose nanocrystals as biological templates

Polyaniline (PANI) is considered as an ideal electrode material due to its remarkable Faradaic activity, exceptional conductivity, and ease of processing. However, the agglomeration and poor cycling stability of PANI largely limit its practical utilization in energy storage devices. To address these challenges, PANI was synthesized via a facile one-pot, two-step process using cellulose nanocrystals (CNCs) as bio-templates in this work. Zeta potential and particle size measurements revealed that the CNC template could impart improved dispersion stability to the synthesized PANI, which exhibited a decrease in average particle size from 1100 nm to 300 nm as a function of 10 % CNCs. Furthermore, the effect of CNC loadings on the performance of PANI was systematically investigated. The results showed that the specific capacitance of PANI/CNC increased from 102.52 F·g-1 to 138.12 F·g-1 with the CNC loading increase from 0 to 10 wt%. Particularly, the PANI/CNC composite film with a 1:9 ratio (C-P-10 %) demonstrated a capacity retention of 84.45 % after 6000 cycles and an outstanding conductivity of 526 S·m-1. This work generally offers an effective solution for the preparation of high-performance PANI-based composites, which might hold great promise in energy storage device applications.

A Top-Down Approach to the Fabrication of Flame-Retardant Wood Aerogel with In Situ-Synthesized Borax and Zinc Borate

In this study, a top-down approach was employed for the fabrication of flame-retardant wood aerogels. The process involved the removal of lignin and the removal of hemicellulose utilizing NaOH concomitantly with the incorporation of ZnO and urea. Subsequently, an in situ reaction with boric acid was conducted to prepare flame-retardant wood aerogels. The morphology, chemical composition, thermal stability, and flame retardancy of the samples were studied. The results show that the NaOH treatment transformed the wood into a layered structure, and flame-retardant particles were uniformly distributed on the surface of the aerogel. The peak heat release rate (PHRR) and total heat release (THR) of the flame-retardant aerogel were significantly reduced compared with the control samples. Meanwhile, its vertical burning test (UL-94) rating reached the V-0 level, and the Limiting Oxygen Index (LOI) could exceed 90%. The flame-retardant wood aerogel exhibited excellent flame retardancy and self-extinguishing properties.

Superstrong Ionogel Enabled by Coacervation-Induced Nanofibril Assembly for Sustainable Moisture Energy Harvesting

Ionogels have grabbed significant interest in various applications, from sensors and actuators to wearable electronics and energy storage devices. However, current ionogels suffer from low strength and poor ionic conductivity, limiting their performance in practical applications. Here, inspired by the mechanical reinforcement of natural biomacromolecules through noncovalent aggregates, a strategy is proposed to construct nanofibril-based ionogels through complex coacervation-induced assembly. Cellulose nanofibrils (CNFs) can bundle together with poly(ionic liquid) (PIL) to form a superstrong nanofibrous network, in which the ionic liquid (IL) can be retained to form ionogels with high liquid inclusion and ionic conductivity. The strength of the CNF-PIL-IL ionogels can be tuned by the IL content over a wide range of up to 78 MPa. The optical transparency, high strength, and hygroscopicity enabled them to be promising candidates in moist-electricity generation and applications such as energy harvesting windows and wearable power generators. In addition, the ionogels are degradable and the ionogel-based generators can be recycled through dehydration. Our strategy suggests perspectives for the fabrication of high-strength and multifunctional ionogels for sustainable applications.

Environmental Sustainability and Physicochemical Property Screening of Chitin and Chitin-Glucan from 22 Fungal Species

Thanks to its biobased character with embedded biogenic carbon, chitin can aid in the transition to a sustainable circular economy by replacing fossil carbon from the geosphere. However, meeting current demands for material availability and environmental sustainability requires alternative methods limiting conventional chemical and energy-consuming chitin extraction from crustaceans. To assist future chitinous bioproduct development, this work analyzes the physicochemical properties and potential environmental sustainability of fungal chitin-glucan complexes. A conventional isolation procedure using sodium hydroxide, a weak acid, and short reaction times are applied to the fruiting body of 22 fungal species. Besides, the valorization of underutilized waste streams including Agaricus bisporus and Agaricus brunnescens stipes is investigated. The carbohydrate analysis renders chitin fractions in the range of 9.5-63.5 wt %, while yields vary from 4.2 to 29.9%, and the N-acetylation degree in found in between 53.0 and 98.7%. The sustainability of the process is analyzed using life cycle assessment (LCA), providing impact quantification for global warming potential, terrestrial acidification, freshwater eutrophication, and water use. With 87.5-589.3 kg·CO2-equiv per kilo, potentially lower global warming potential values in comparison to crustacean chitin are achieved. The crystallinity degree ranged from 28 to 78%, while the apparent chitin crystalline size (L020) is between 2.3 and 5.4 nm. Ten of the species yield α-chitin coexisting with semicrystalline glucans. Zwitterionic properties are observed in aqueous solutions, shifting from cationic to anionic at pH 4.5. With its renewable carbon content, fungal chitin is an environmentally sustainable alternative for high-value applications due to its balance of minimal treatment, low carbon footprint, material renewability, ease of isolation, thermal stability, zwitterionic behavior, biodegradability, and noncytotoxicity.

Constructing a 3D Ion Transport Channel-Based CNF Composite Film with an Intercalated Structure for Superior Performance Flexible Supercapacitors

The weak stiffness, huge thickness, and low specific capacitance of commonly utilized flexible supercapacitors hinder their great electrochemical performance. Learning from a biomimetic interface strategy, we design flexible film electrodes based on functional intercalated structures with excellent electrochemical properties and mechanical flexibility. A composite film with high strength and flexibility is created using graphene (reduced graphene oxide (rGO)) as the plane layer, layered double metal hydroxide (LDH) as the support layer, and cellulose nanofiber (CNF) as the connection agent and flexible agent. The interlayer height can be adjusted by the ion concentration. The highly interconnected network enables excellent electron and ion transport channels, facilitating rapid ion diffusion and redox reactions. Moreover, the high flexibility and mechanical properties of the film achieve multiple folding and bending. The CNF-rGO-NiCoLDH film electrode exhibits high capacitance performance (3620.5 mF cm-2 at 2 mA cm-2), excellent mechanical properties, and high flexibility. Notably, flexible all-solid assembled CNF-rGO-NiCoLDH//rGO has an extremely high area energy density of 53.5 mWh cm-2 at a power density of 1071.2 mW cm-2, along with cycling stability of 89.8% retention after 10 000 charge-discharge cycles. This work provides a perspective for designing high-performance energy storage materials for flexible electronics and wearable devices.

Recent Advances in Biopolymer-Based Hydrogel Electrolytes for Flexible Supercapacitors

Growing concern regarding the impact of fossil fuels has led to demands for the development of green and renewable materials for advanced electrochemical energy storage devices. Biopolymers with unique hierarchical structures and physicochemical properties, serving as an appealing platform for the advancement of sustainable energy, have found widespread application in the gel electrolytes of supercapacitors. In this Review, we outline the structure and characteristics of various biopolymers, discuss the proposed mechanisms and assess the evaluation metrics of gel electrolytes in supercapacitor devices, and further analyze the roles of biopolymer materials in this context. The state-of-the-art electrochemical performance of biopolymer-based hydrogel electrolytes for supercapacitors and their multiple functionalities are summarized, while underscoring the current technical challenges and potential solutions. This Review is intended to offer a thorough overview of recent developments in biopolymer-based hydrogel electrolytes, highlighting research concerning green and sustainable energy storage devices and potential avenues for further development.

Nanocellulose-Enhanced, Easily Processable Cellulose-Based Flexible Pressure Sensor for Wearable Epidermal Sensing

Flexible pressure sensors (FPSs) based on biomass materials have gained considerable attention for their potential in wearable electronics, human-machine interaction, and environmental protection. Herein, flexible silver nanowire-dual-cellulose paper (SNdCP) containing common cellulose fibers, cellulose nanofibers (CNFs), and silver nanowires (AgNWs) for FPSs was assembled by a facile papermaking strategy. Compared with bacterial cellulose (BC) and cellulose nanocrystals (CNCs), CNFs possess better dimensions and reinforcement, which enables the composite paper to exhibit better mechanical properties (tensile stress of 164.65 MPa) and electrical conductivity (11600 S·m-1), providing more possibilities for FPSs. Benefiting from these advantages, we construct an easily processable and sensitive human-interactive FPS based on a composite paper with high sensitivity (0.050 kPa-1), fast response/recovery time (158/95 ms), and exceptional stability (>1000 bending cycles), capable of responding to finger motions, voice recognition, and human pulses; through further employment as the array unit and a control circuit, the observed highly adaptive mechano-electric transformability and functions are well maintained. Overall, a facile and versatile strategy with the potential to provide clues for the fabrication of cellulose-based FPSs with outstanding performance was introduced.

Innovative modification of cellulose fibers for paper-based electrode materials using metal-organic coordination polymers

Cellulosic paper-based electrode materials have attracted increasing attention in the field of flexible supercapacitor. As a conductive polymer, polyaniline exhibits high theoretical pseudocapacitive capacitance and has been applied in paper-based electrode materials along with cellulose fibers. However, the stacking of polyaniline usually leads to poor performance of electrodes. In this study, metal-organic coordination polymers of zirconium-alizarin red S and zirconium-phytic acid are applied to modulate the polyaniline layer to obtain high-performance cellulosic paper-based electrode materials. Zirconium hydroxide is firstly loaded on cellulose fibers while alizarin red S and phytic acid are introduced to regulate the morphology of polyaniline through doping and coordination processes. The results show that the introduction of dual coordination polymers is effective to regulate the morphology of polyaniline on cellulose fibers. The performances of the paper-based electrode materials, including electrical conductivity and electrochemistry, are apparently improved. It provides a promising strategy for the potential development of economical and green electrode materials in the conventional paper-making process.

Heteroatom-doped and graphitization-enhanced lignin-derived hierarchically porous carbon via facile assembly of lignin-Fe coordination for high-voltage symmetric supercapacitors

Lignin-derived carbon materials are widely used as electrode materials for supercapacitors. However, the electrochemical performance of these materials is limited by the surface chemistry and pore structure characteristics. Herein, a novel and sustainable strategy was proposed to prepare heteroatom-doped lignin-derived carbon material (Fe-NLC) with well-developed pore size distributions and enhanced graphitization structure via a facile lignin-Fe coordination method followed by carbonization. During carbonization, Fe3+ in lignin-metal complexes evolve into nanoparticles, which act as templates to introduce porous structures in carbon materials. Also, the lignin-Fe coordination structure endows the material with a higher graphitization during carbonization, thereby improving the structural properties of the carbon materials. Due to the removal of Fe3O4 template, the obtained Fe-NLC possessed reasonable pore distribution and nitrigen/oxygen (N/O) functional groups, which can improve the wettability of materials and introduce pseudocapacitance. Accordingly, Fe-NLC possesses a notable specific capacitance of 264 F/g at 0.5 A/g. Furthermore, a symmetric supercapacitor Fe-NLC//Fe-NLC with a high voltage window (1.8 V) was constructed. The symmetric supercapacitor exhibits a maximum energy density of 15.97 Wh/kg at 450 W/kg, demonstrating well application prospects. This paper proposes a novel approach for preparing carbon materials via lignin-metal coordination to provide an alternative way to explore sustainable and low-cost energy storage materials.

Nanocrystalline Cellulose-Supported Iron Oxide Composite Materials for High-Performance Lithium-Ion Batteries

Nanocrystalline cellulose (NCC) can be converted into carbon materials for the fabrication of lithium-ion batteries (LIBs) as well as serve as a substrate for the incorporation of transition metal oxides (TMOs) to restrain the volume expansion, one of the most significant challenges of TMO-based LIBs. To improve the electrochemical performance and enhance the longer cycling stability of LIBs, a nanocrystalline cellulose-supported iron oxide (Fe2O3) composite (denoted as NCC-Fe2O3) is synthesized and utilized as electrodes in LIBs. The obtained NCC-Fe2O3 electrode exhibited stable cycling performance, better capacity, and high-rate capacity, and delivered a specific discharge capacity of 576.70 mAh g-1 at 100 mA g-1 after 1000 cycles. Moreover, the NCC-Fe2O3 electrode was restored and showed an upward trend of capacity after working at high current densities, indicating the fabricated composite is a promising approach to designing next-generation high-energy density lithium-ion batteries.

Bottom-Up Magnesium Deposition Induced by Paper-Based Triple-Gradient Scaffolds toward Flexible Magnesium Metal Batteries

The development of advanced magnesium metal batteries (MMBs) has been hindered by longstanding challenges, such as the inability to induce uniform magnesium (Mg) nucleation and the inefficient utilization of Mg foil. This study introduces a novel solution in the form of a flexible, lightweight, paper-based scaffold that incorporates gradient conductivity, magnesiophilicity, and pore size. This design is achieved through an industrially adaptable papermaking process in which the ratio of carboxylated multi-walled carbon nanotubes to softwood cellulose fibers is meticulously adjusted. The triple-gradient structure of the scaffold enables the regulation of Mg ion flux, promoting bottom-up Mg deposition. Owing to its high flexibility, low thickness, and reduced density, the scaffold has potential applications in flexible and wearable electronics. Accordingly, the triple-gradient electrodes exhibit stable operation for over 1200 h at 3 mA cm-2 /3 mAh cm-2 in symmetrical cells, markedly outperforming the non-gradient and metallic Mg alternatives. Notably, this study marks the first successful fabrication of a flexible MMB pouch full cell, achieving an impressive volumetric energy density of 244 Wh L-1 . The simplicity and scalability of the triple-gradient design, which uses readily available materials through an industrially compatible papermaking process, open new doors for the production of flexible, high-energy-density metal batteries.

Highly Stretchable, Knittable, Wearable Fiberform Hydrovoltaic Generators Driven by Water Transpiration for Portable Self-Power Supply and Self-Powered Strain Sensor

The development of excellently stretchable, highly mobile, and sustainable power supplies is of great importance for self-power wearable electronics. Transpiration-driven hydrovoltaic power generator (HPG) has been demonstrated to be a promising energy harvesting strategy with the advantages of negative heat and zero-carbon emissions. Herein, this work demonstrates a fiber-based stretchable HPG with the advantages of high output, portability, knittability, and sustainable power generation. Based on the functionalized micro-nano water diffusion channels constructed by the discarded mask straps (MSs) and oxidation-treated carbon nanomaterials, the applied water can continuously produce electricity during the spontaneous flow and diffusion. Experimentally, when a tiny 0.1 mL of water encounters one end of the proposed HPG, the centimeter-length device can yield a peak voltage of 0.43 V, peak current of 29.5 µA, and energy density of 5.833 mW h cm-3. By efficiently integrating multiple power generation units, sufficient output power can be provided to drive commercial electronic devices even in the stretched state. Furthermore, due to the reversibility of the electrical output during dynamic stretching-releasing, it can passively convert physiological activities and motion behaviors into quantifiable and processable current signals, opening up HPG's application in the field of self-powered wearable sensing.

Advanced hydrostable, recyclable and degradable cellulose hybrid films as renewable alternatives to synthetic plastics

Strong, tough and sustainable materials are in high demand in various engineering applications. We demonstrate a potential sustainable hybrid film made from natural cellulose and a biobased slurry. Through a simple and scalable approach, cellulose can be processed into an advanced material with over 2.8 and 9.2-fold increase in dry strength and toughness after curing and a 728-fold increase in wet strength, respectively. In addition, these hybrid composite films display an outstanding antioxidant activity surpassing 90 %, along with excellent ultraviolet radiation shielding and thermal insulation properties. Further, the hybrid films can be fabricated by integrating all-natural materials and still guarantee their unique functionality. We also demonstrate the feasibility of a circular bioeconomy by recycling the hybrid film using a green, deep eutectic solvent to fabricate a recycled hybrid film that displays excellent mechanical and optical properties. When recycling is unsuitable or economical, the hybrid film can naturally degrade in the soil under 6 months. These encouraging findings suggest the promise of cellulose hybrid films as a renewable, low-cost, tough, and strong material with the potential to replace nonrenewable synthetic plastics and products.

A Bioinspired Gradient Design Strategy for Cellulose-Based Electromagnetic Wave Absorbing Structural Materials

Cellulose nanofiber (CNF) possesses excellent intrinsic properties, and many CNF-based high-performance structural and functional materials have been developed recently. However, the coordination of the mechanical properties and functionality is still a considerable challenge. Here, a CNF-based structural material is developed by a bioinspired gradient structure design using hollow magnetite nanoparticles and the phosphorylation-modified CNF as building blocks, which simultaneously achieves a superior mechanical performance and electromagnetic wave absorption (EMA) ability. Benefiting from the gradient design, the flexural strength of the structural material reached ∼205 MPa. Meanwhile, gradient design improves impedance matching, contributing to the high EMA ability (-59.5 dB) and wide effective absorption width (5.20 GHz). Besides, a low coefficient of thermal expansion and stable storage modulus was demonstrated as the temperature changes. The excellent mechanical, thermal, and EMA performance exhibited great potential for application in stealth equipment and electromagnetic interference protecting electronic packaging materials.

Exploring the Versatility of Aerogels: Broad Applications in Biomedical Engineering, Astronautics, Energy Storage, Biosensing, and Current Progress

Aerogels are unique and extremely porous substances with fascinating characteristics such as ultra-low density, extraordinary surface area, and excellent thermal insulation capabilities. Due to their exceptional features, aerogels have attracted significant interest from various fields, including energy, environment, aerospace, and biomedical engineering. This review paper presents an overview of the trailblazing research on aerogels, aiming at their preparation, characterization, and applications. Various methods of aerogel synthesis, such as sol-gel, supercritical drying, are discussed. Additionally, recent progress in the characterization of aerogel structures, including their morphology, porosity, and thermal properties, are extensively reviewed. Finally, aerogel's utilizations in numerous disciplines, for instance, energy storage, thermal insulation, catalysis, environmental remedy, and biomedical applications, are summarized. This review paper provides a comprehensive understanding of aerogels and their prospective uses in diverse fields, highlighting their unique properties for future research and development.

Highly Strong, Tough, and Cryogenically Adaptive Hydrogel Ionic Conductors via Coordination Interactions

Despite the promise of high flexibility and conformability of hydrogel ionic conductors, existing polymeric conductive hydrogels have long suffered from compromises in mechanical, electrical, and cryoadaptive properties due to monotonous functional improvement strategies, leading to lingering challenges. Here, we propose an all-in-one strategy for the preparation of poly(acrylic acid)/cellulose (PAA/Cel) hydrogel ionic conductors in a facile yet effective manner combining acrylic acid and salt-dissolved cellulose, in which abundant zinc ions simultaneously form strong coordination interactions with the two polymers, while free solute salts contribute to ionic conductivity and bind water molecules to prevent freezing. Therefore, the developed PAA/Cel hydrogel simultaneously achieved excellent mechanical, conductive, and cryogenically adaptive properties, with performances of 42.5 MPa for compressive strength, 1.6 MPa for tensile strength, 896.9% for stretchability, 9.2 MJ m-3 for toughness, 59.5 kJ m-2 for fracture energy, and 13.9 and 6.2 mS cm-1 for ionic conductivity at 25 and -70 °C, respectively. Enabled by these features, the resultant hydrogel ionic conductor is further demonstrated to be assembled as a self-powered electronic skin (e-skin) with high signal-to-noise ratio for use in monitoring movement and physiological signals regardless of cold temperatures, with hinting that could go beyond high-performance hydrogel ionic conductors.

Unleashing the Potential of MXene-Based Flexible Materials for High-Performance Energy Storage Devices

Since the initial discovery of Ti3 C2 a decade ago, there has been a significant surge of interest in 2D MXenes and MXene-based composites. This can be attributed to the remarkable intrinsic properties exhibited by MXenes, including metallic conductivity, abundant functional groups, unique layered microstructure, and the ability to control interlayer spacing. These properties contribute to the exceptional electrical and mechanical performance of MXenes, rendering them highly suitable for implementation as candidate materials in flexible and wearable energy storage devices. Recently, a substantial number of novel research has been dedicated to exploring MXene-based flexible materials with diverse functionalities and specifically designed structures, aiming to enhance the efficiency of energy storage systems. In this review, a comprehensive overview of the synthesis and fabrication strategies employed in the development of these diverse MXene-based materials is provided. Furthermore, an in-depth analysis of the energy storage applications exhibited by these innovative flexible materials, encompassing supercapacitors, Li-ion batteries, Li-S batteries, and other potential avenues, is conducted. In addition to presenting the current state of the field, the challenges encountered in the implementation of MXene-based flexible materials are also highlighted and insights are provided into future research directions and prospects.

Interfacial Modulation of Ti3 C2 Tx MXene by Cellulose Nanofibrils to Construct Hybrid Fibers with High Volumetric Specific Capacitance

The intrinsic poor rheological properties of MXene inks result in the MXene nanosheets in dried MXene microfibers prone to self-stacking, which is not conducive to ion transport and diffusion, thus affecting the electrochemical performance of fiber-based supercapacitors. Herein, robust cellulose nanofibrils (CNF)/MXene hybrid fibers with high electrical conductivity (916.0 S cm-1 ) and narrowly distributed mesopores are developed by wet spinning. The interfacial interaction between CNF and MXene can be enhanced by hydrogen bonding and electrostatic interaction due to their rich surface functional groups. The interfacial modulation of MXene by CNF can not only regulate the rheology of MXene spinning dispersion, but also enhance the mechanical strength. Furthermore, the interlayer distance and self-stacking effect of MXene nanosheets are also regulated. Thus, the ion transport path within the fiber material is optimized and ion transport is accelerated. In H2 SO4 electrolyte, a volumetric specific capacitance of up to 1457.0 F cm-3 (1.5 A cm-3 ) and reversible charge/discharge stability are demonstrated. Intriguingly, the assembled supercapacitors exhibit a high-volume energy density of 30.1 mWh cm-3 at 40.0 mW cm-3 . Moreover, the device shows excellent flexibility and cycling stability, maintaining 83% of its initial capacitance after 10 000 charge/discharge cycles. Practical energy supply applications (Power for LED and electronic watch) can be realized.

Incorporation of Cellulose-Based Aerogels into Textile Structures

Given their exceptional attributes, aerogels are viewed as a material with immense potential. Being a natural polymer, cellulose offers the advantage of being both replenishable and capable of breaking down naturally. Cellulose-derived aerogels encompass the replenish ability, biocompatible nature, and ability to degrade naturally inherent in cellulose, along with additional benefits like minimal weight, extensive porosity, and expansive specific surface area. Even with increasing appreciation and acceptance, the undiscovered possibilities of aerogels within the textiles sphere continue to be predominantly uninvestigated. In this context, we outline the latest advancements in the study of cellulose aerogels' formulation and their diverse impacts on textile formations. Drawing from the latest studies, we reviewed the materials used for the creation of various kinds of cellulose-focused aerogels and their properties, analytical techniques, and multiple functionalities in relation to textiles. This comprehensive analysis extensively covers the diverse strategies employed to enhance the multifunctionality of cellulose-based aerogels in the textiles industry. Additionally, we focused on the global market size of bio-derivative aerogels, companies in the industry producing goods, and prospects moving forward.

Self-Recovery of a Buckling BaTiO3 Ferroelectric Membrane

The characteristic of self-recovery holds significant implications for upholding performance stability within flexible electronic devices following the release of mechanical deformation. Herein, the dynamics of self-recovery in a buckling inorganic membrane is studied via in situ scanning probe microscopy technology. The experimental results demonstrate that the ultimate deformation ratio of the buckling BaTiO3 ferroelectric membrane is up to 88%, which is much higher than that of the buckling SrTiO3 dielectric membrane (49%). Combined with piezoresponse force microscopy and phase-field simulations, we find that ferroelectric domain transformation accompanies the whole process of buckling and self-recovery of the ferroelectric membrane, i.e., the presence of the nano-c domain not only releases part of the elastic energy of the membrane but also reduces the interface mismatch of the a/c domain, which encourages the buckling ferroelectric membrane to have excellent self-recovery properties. It is conceivable that the evolution of ferroelectric domains will play a greater role in the regulation of the mechanical properties of ferroelectric membranes and flexible devices.

Engineering Self-Adaptive Multi-Response Thermochromic Hydrogel for Energy-Saving Smart Windows and Wearable Temperature-Sensing

Buildings account for ≈40% of the total energy consumption. In addition, it is challenging to control the indoor temperature in extreme weather. Therefore, energy-saving smart windows with light regulation have gained increasing attention. However, most emerging base materials for smart windows have disadvantages, including low transparency at low temperatures, ultra-high phase transition temperature, and scarce applications. Herein, a self-adaptive multi-response thermochromic hydrogel (PHC-Gel) with dual temperature and pH response is engineered through "one-pot" integration tactics. The PHC-Gel exhibits excellent mechanical, adhesion, and electrical conductivity properties. Notably, the low critical solubility temperature (LCST) of PHC-Gel can be regulated over a wide temperature range (20-35 °C). The outdoor practical testing reveals that PHC-Gel has excellent light transmittance at low temperatures and radiation cooling performances at high temperatures, indicating that PHC-Gel can be used for developing energy-saving windows. Actually, PHC-Gel-based thermochromic windows show remarkable visible light transparency (Tlum ≈ 95.2%) and solar modulation (△Tsol ≈ 57.2%). Interestingly, PHC-Gel has superior electrical conductivity, suggesting that PHC-Gel can be utilized to fabricate wearable signal-response and temperature sensors. In summary, PHC-Gel has broad application prospects in energy-saving smart windows, smart wearable sensors, temperature monitors, infant temperature detection, and thermal management.

Plastic Chip Electrode: An Emerging Multipurpose Electrode Platform

The properties of electrodes play a crucial role in the processes occurring on them. Therefore, a variety of materials have been tried as electrodes. Carbon composite materials are among the most admired ones. Use of composites as electrode material dates back to the mid of the last century when polymer-carbon composites were tried as general-purpose electrode platforms and epoxy impregnated graphite paste/ solid electrodes were tried in polarography. Later the composite electrodes have seen several phases of development. Plastic Chip Electrode (PCE) is a class of polymer composite electrode developed by our group. This monographic review gives a bird's eye account of polymer composite electrodes and appurtenant work, followed by elaborating on various aspects and state-of-the-art plastic chip electrodes.

Study on the Construction of Interlayer Adjustable C@MoS2 Fiber Anode by Biomass Confining and its Lithium/Sodium Storage Mechanism

Building a stable and controllable interlayer structure is the key to improving the sodium storage cycling stability and rate performance of two-dimensional anode materials. This study explored the rich functional groups in bacterial cellulose culture medium in the way of biological self-assembly. Mo precursors were used to produce chemical bond in bacterial cellulose culture medium, and intercalation groups are introduced to achieve MoS2 localized nucleation and in situ localized construction of carbon intercalation stable interlaminar structure, thus improving ion transport dynamics and cycle stability. In order to avoid structural irreversibility of MoS2 at low potential, an extended voltage window of 1.5-4 V was selected for lithium/sodium intercalation testing. It was found that there was a significant improvement in sodium storage capacity and stability. During the electrochemical cycling process, in-situ Raman testing revealed that the structure of MoS2 was completely reversible, and the intensity changes of MoS2 characteristic peaks showed in-plane vibration without involving interlayer bonding fracture. Moreover, after the lithium sodium was removed from the intercalation C@MoS2 all structures have good retention.

Carboxymethylcellulose/poly(3,4-ethylenedioxythiophene):polystyrene sulfonate membrane after dimethyl sulfoxide treatment for flexible and high electrochemical performance asymmetric supercapacitors

As the requirements for wearable electronic devices continue to increase, the development of bendable and foldable supercapacitors is becoming critical. However, it is still challenging to design free-standing electrodes with flexibility and high electrical conductivity. Herein, using carboxymethylcellulose (CMC) as the biological template and poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) as the electroactive material, a flexible CMC/PEDOT:PSS membrane with a cross-linked mesh structure was firstly synthesized by a facile in-situ polymerization and vacuum filtration process. Subsequently, the CMC/PEDOT:PSS membrane was further treated with dimethyl sulfoxide (DMSO) to remove the excess PSS, thereby enhancing their electrochemical performance. The results showed that the best performing hybrid membrane had good mechanical properties (tensile strength of 48.1 MPa) and high electrical conductivity (45.1 S cm-1). The assembled asymmetric supercapacitor (ASC) is capable of delivering an energy density of 181.9 μW h cm-2 at a power density of 750 μW cm-2 and maintains an initial capacitance of 93.4 % and a coulombic efficiency of 100 % after 10,000 GCD cycles, demonstrating an ultra-long cycle life. Moreover, good electrochemical properties can be retained even in the bent and folded state. Therefore, the hybrid membrane electrode with both flexibility and high electrochemical performance has great potential for application in wearable electronics.

Tough and strong sustainable thermoplastic elastomers nanocomposite with self-assembly of SI-ATRP modified cellulose nanofibers

The ingenious design of sustainable thermoplastic elastomers (STPEs) is of great significance for the goal of the sustainable development. However, the preparation of STPEs with good mechanical performance is still complicated and challenging. Herein, to achieve a simple preparation of STPEs with strong mechanical properties, two biobased monomers (tetrahydrofurfuryl methacrylate (THFMA) and lauryl methacrylate (LMA)) were copolymerized into poly (THFMA-co-LMA) (PTL) and grafted onto TEMPO oxidized cellulose nanofiber (TOCN) via one-pot surface-initiated atom transfer radical polymerization (SI ATRP). The grafting modified TOCN could be self-assembled into nano-enhanced phases in STPEs, which are conducive to the double enhancement of the strength and toughness of the STPEs, and the size of nano-enhanced phases is mainly affected by TOCN fiber length and molecular weight of grafting chains. Especially, with the addition of 7 wt% TOCN, tensile strength, tensile strain, toughness, and glass transition temperature (Tg) of TOCN based STPEs (TOCN@PTL) exhibited 140 %, 36 %, 215 %, and 6.8 °C increase respectively, which confirmed the leading level in the field of bio-based elastomers. In general, this work constitutes a proof for the chemical modification and self-assembly behavior of TOCN by one-pot SI ATRP, and provides an alternative strategy for the preparation of high-performance STPEs.

MXene-Mediated Cellulose Conductive Hydrogel with Ultrastretchability and Self-Healing Ability

Constructing natural polymers such as cellulose, chitin, and chitosan into hydrogels with excellent stretchability and self-healing properties can greatly expand their applications but remains very challenging. Generally, the polysaccharide-based hydrogels have suffered from the trade-off between stiffness of the polysaccharide and stretchability due to the inherent nature. Thus, polysaccharide-based hydrogels (polysaccharides act as the matrix) with self-healing properties and excellent stretchability are scarcely reported. Here, a solvent-assisted strategy was developed to construct MXene-mediated cellulose conductive hydrogels with excellent stretchability (∼5300%) and self-healability. MXene (an emerging two-dimensional nanomaterial) was introduced as emerging noncovalent cross-linking sites between the solvated cellulose chains in a benzyltrimethylammonium hydroxide aqueous solution. The electrostatic interaction between the cellulose chains and terminal functional groups (O, OH, F) of MXene led to cross-linking of the cellulose chains by MXene to form a hydrogel. Due to the excellent properties of the cellulose-MXene conductive hydrogel, the work not only enabled their strong potential in both fields of electronic skins and energy storage but provided fresh ideas for some other stubborn polymers such as chitin to prepare hydrogels with excellent properties.

Cellulose-Based Conductive Materials for Energy and Sensing Applications

Cellulose-based conductive materials (CCMs) have emerged as a promising class of materials with various applications in energy and sensing. This review provides a comprehensive overview of the synthesis methods and properties of CCMs and their applications in batteries, supercapacitors, chemical sensors, biosensors, and mechanical sensors. Derived from renewable resources, cellulose serves as a scaffold for integrating conductive additives such as carbon nanotubes (CNTs), graphene, metal particles, metal-organic frameworks (MOFs), carbides and nitrides of transition metals (MXene), and conductive polymers. This combination results in materials with excellent electrical conductivity while retaining the eco-friendliness and biocompatibility of cellulose. In the field of energy storage, CCMs show great potential for batteries and supercapacitors due to their high surface area, excellent mechanical strength, tunable chemistry, and high porosity. Their flexibility makes them ideal for wearable and flexible electronics, contributing to advances in portable energy storage and electronic integration into various substrates. In addition, CCMs play a key role in sensing applications. Their biocompatibility allows for the development of implantable biosensors and biodegradable environmental sensors to meet the growing demand for health and environmental monitoring. Looking to the future, this review emphasizes the need for scalable synthetic methods, improved mechanical and thermal properties, and exploration of novel cellulose sources and modifications. Continued innovation in CCMs promises to revolutionize sustainable energy storage and sensing technologies, providing environmentally friendly solutions to pressing global challenges.

Lignocellulose-Based Optical Biofilter with High Near-Infrared Transmittance via Lignin Capturing-Fusing Approach

Near-infrared (NIR) transparent optical filters show great promise in night vision and receiving windows. However, NIR optical filters are generally prepared by laborious, environmentally unfriendly processes that involve metal oxides or petroleum-based polymers. We propose a lignin capturing-fusing approach to manufacturing optical biofilters based on molecular collaboration between lignin and cellulose from waste agricultural biomass. In this process, lignin is captured via self-assembly in a cellulose network; then, the lignin is fused to fill gaps and hold the cellulose fibers tightly. The resulting optical biofilter featured a dense structure and smooth surface with NIR transmittance of ~90%, ultralow haze of close to 0%, strong ultraviolet-visible light blocking (~100% at 400 nm and 57.58% to 98.59% at 550 nm). Further, the optical biofilter has comprehensive stability, including water stability, solvent stability, thermal stability, and environmental stability. Because of its unique properties, the optical biofilter demonstrates potential applications in the NIR region, such as an NIR-transmitting window, NIR night vision, and privacy protection. These applications represent a promising route to produce NIR transparent optical filters starting from lignocellulose biomass waste.

Flexible MXene/Nanocellulose Composite Aerogel Film with Cellular Structure for Electromagnetic Interference Shielding and Photothermal Conversion

With the rapid development of wearable devices and integrated systems, protection against electromagnetic waves is an issue. For solving the problems of poor flexibility and a tendency to corrode traditional electromagnetic interference (EMI) shielding materials, two-dimensional (2D) nanomaterial MXene was employed to manufacture next-generation EMI shielding materials. Vacuum-assisted filtration combined with the liquid nitrogen prefreezing strategy was adopted to prepare flexible MXene/cellulose nanofibers (CNFs) composite aerogel film with unique cellular structure. Here, CNFs were employed as the reinforcement, and such a cellular structure design can effectively improve the shielding effectiveness (SE). In particular, the composite shows an outstanding EMI SE of 54 dB. Furthermore, the MXene/CNFs composite aerogel film exhibited prominent and steady photothermal conversion ability, which could obtain the maximum equilibrium temperature of 89.4 °C under an 808 nm NIR laser. Thus, our flexible composite aerogel film with appealing cellular construction holds great promise for wearable EMI shielding materials and heating applications in a cold and complex practical environment.

Sulfur-doped carbonized bacterial cellulose as a flexible binder-free 3D anode for improved sodium ion storage

Carbon-based materials have received wide attention as electrodes for energy storage and conversion owing to their rapid mass transfer processes, outstanding electronic conductivities, and high stabilities. Here, sulfur-doped carbonized bacterial cellulose (S-CBC) was prepared as a high-performance anode for sodium-ion batteries (SIBs) by simultaneous carbonization and sulfidation using the bacterial cellulose membrane produced by microbial fermentation as the precursor. Doping sublimed sulfur powder into CBC results in a greater degree of disorder and defects, buffering the volume expansion during the cycle. Significantly, the three-dimensional (3D) network structure of bacterial cellulose endows S-CBC with flexible self-support. As an anode for sodium ion batteries, S-CBC exhibits a high specific capacity of 302.9 mA h g-1 at 100 mA g-1 after 50 cycles and 177.6 mA h g-1 at 2 A g-1 after 1000 cycles. Compared with the CBC electrode, the S-CBC electrode also exhibits enhanced rate performance in sodium storage. Moreover, theoretical simulations reveal that Na+ has good adsorption stability and a faster diffusion rate in S-CBC. The doping of the S element introduces defects that enlarge the interlayer distance, and the synergies of adsorption and bonding are the main reasons for its high performance. These results indicate the potential application prospects of S-CBC as a flexible binder-free electrode for high-performance SIBs.

Zinc Vacancy Promotes Photo-Reforming Lignin Model to H2 Evolution and Value-Added Chemicals Production

Lignin, rich in β-O-4 bonds and aromatic structure, is a renewable and potential resource for value-added chemicals and promoting H2 evolution. However, direct photo-reforming lignin remains a huge challenge due to its recalcitrant structure. Herein, a collaborative strategy is proposed by dispersing Pt on zinc-vacancy-riched ZnIn2 S4 (Pt/VZn -ZIS) for revealing the effect of lignin structure during photo-reforming process with lignin models. And a series of theoretical calculations and experimental results show that lignin model substances with more nucleophilic group structures will have a stronger tendency to occur the photo-reforming reactions. In addition, benefiting of Pt-S electronic channel is formed by occupying Pt atom onto zinc vacancies in ZnIn2 S4 , which can effectively reduce the energy barrier of H2 evolution and accompany the selective oxidation of lignin model from Cα-OH to Cα = O under simulated sunlight. The natural lignin is used to further demonstrate this selective oxidation mechanism. The presented work demonstrates the photo-reforming lignin model mechanism and the influence of lignin-structure during the process of photo-reforming.

Biomass-Derived Flexible Carbon Architectures as Self-Supporting Electrodes for Energy Storage

With the swift advancement of the wearable electronic devices industry, the energy storage components of these devices must possess the capability to maintain stable mechanical and chemical properties after undergoing multiple bending or tensile deformations. This circumstance has expedited research efforts toward novel electrode materials for flexible energy storage devices. Nonetheless, among the numerous materials investigated to date, the incorporation of metal current collectors or insulative adhesives remains requisite, which entails additional costs, unnecessary weight, and high contact resistance. At present, biomass-derived flexible architectures stand out as a promising choice in electrochemical energy device applications. Flexible self-supporting properties impart a heightened mechanical performance, obviating the need for additional binders and lowering the contact resistance. Renewable, earth-abundant biomass endows these materials with cost-effectiveness, diversity, and modulable chemical properties. To fully exploit the application potential in biomass-derived flexible carbon architectures, understanding the latest advancements and the comprehensive foundation behind their synthesis assumes significance. This review delves into the comprehensive analysis of biomass feedstocks and methods employed in the synthesis of flexible self-supporting carbon electrodes. Subsequently, the advancements in their application in energy storage devices are elucidated. Finally, an outlook on the potential of flexible carbon architectures and the challenges they face is provided.

Triphenylamine-Based Helical Polymer for Flexible Memristors

Flexible nonvolatile memristors have potential applications in wearable devices. In this work, a helical polymer, poly (N, N-diphenylanline isocyanide) (PPIC), was synthesized as the active layer, and flexible electronic devices with an Al/PPIC/ITO architecture were prepared on a polyethylene terephthalate (PET) substrate. The device showed typical nonvolatile rewritable memristor characteristics. The high-molecular-weight helical structure stabilized the active layer under different bending degrees, bending times, and number of bending cycles. The memristor was further employed to simulate the information transmission capability of neural fibers, providing new perspectives for the development of flexible wearable memristors and biomimetic neural synapses. This demonstration highlights the promising possibilities for the advancement of artificial intelligence skin and intelligent flexible robots in the future.

Construction of composite films using carbon nanodots for blocking ultraviolet light from the Sun

Carbon nanodots (CNDs) which demonstrate concentration-dependent emission and have a photoluminescence quantum yield of 45% were designed. Transparent CND-containing composite films (CND-films), obtained by combining the CNDs with polyvinyl alcohol in different proportions, were shown to block the UV component of sunlight. Whereas the pure PVA film could not block UV light, the ability of CND-films to block UV light could be adjusted by altering the proportion of CNDs in the film. The larger the proportion of CNDs, the greater the extent of UV blocking. CND-film containing 32 wt% CNDs completely blocked UV light (≤400 nm) from sunlight, without affecting the transmission of visible light (>800 nm). The ability of the CND-films to block the UV component of sunlight was investigated using a commercially available UV-induced color change card, which confirmed that the capacity of the CND-films to block UV light could be adjusted by altering the proportion of CNDs in the film. This study shows that CNDs with concentration-dependent long wavelength emission characteristics can be used as optical barrier units for the preparation of materials to block high-energy short wavelength light.

High mass loading paper-based electrode material with cellulose fibers under coordination of zirconium oxyhydroxide nanoparticles and sulfosalicylic acid

With the rapid expansion of the flexible electronics market, it is critical to develop high-performance flexible energy storage electrode materials. Cellulose fibers, which are sustainable, low cost, and flexible, fully meet the requirements of flexible electrode materials, but they are electrically insulating and cause a decrease in energy density. In this study, high-performance paper-based flexible electrode materials (PANI:SSA/Zr-CFs) were prepared with cellulose fibers and polyaniline. A high mass loading of polyaniline was wrapped on zirconia hydroxide-modified cellulose fibers under metal-organic acid coordination through a facile in situ chemical polymerization process. The increase in mass loading of PANI on cellulose fibers not only improves the electrical conductivity but also enhances the area-specific capacitance of the flexible electrodes. The results of electrochemical tests show that the area specific capacitance of the PANI:SSA/Zr-CFs electrode is 4181 mF/cm² at 1 mA/cm², which is more than two times higher than that of the electrode with PANI on pristine CFs. This work provides a new strategy for the design and manufacture of high-performance flexible electronic electrodes based on cellulose fibers.