Time-dependent degradation and toxicity of diclofop-methyl in algal suspensions : emerging contaminants

Investigation of the removal of diclofop methyl herbicide by peroxy electrocoagulation process and kinetic and cost analysis

Pesticides containing chlorine, which are released during agricultural activities, are chemical substances that mix with surface and underground waters and have toxic, carcinogenic, and mutagenic effects on the entire living ecosystem. Due to their chemically stable structure, conventional water and wastewater treatment techniques such as coagulation, flocculation, and biological oxidation do not entirely remove these chemical substances. Therefore, before releasing them into the environmental receptor, these chemical substances must be transformed into harmless products or mineralized through advanced oxidation processes. When we look at the literature, there are not many studies on methods of removing diclofop methyl from aquatic media. Our study on the removal of diclofop methyl herbicide from aquatic media using the peroxy electrocoagulation method will provide the first information on this subject in the literature. In addition, this treatment method will contribute significantly to filling an important gap in the literature as an innovative approach for diclofop methyl removal. Moreover, peroxy electrocoagulation, which produces less sludge, provides treatment in a short time, and is economical, has been determined to be an advantageous process. The effects of conductivity, pH, H2O2 concentration, current, and time parameters on the removal of diclofop methyl were investigated using a GC-MS instrument. Kinetics, energy consumption, and cost calculations were also made. Under the optimum conditions determined (pH = 5, H2O2 = 500 mg/L, NaCl = 0.75 g/L, current density = 2.66 mA/cm2), the peroxydic electrocoagulation process resulted in a diclofop methyl removal efficiency of 79.2% after a 25-min reaction. When the experimental results were analyzed, it was found that the results fitted the pseudo-second-order kinetic model.

Ecotoxicity of Diazinon and Atrazine Mixtures after Ozonation Catalyzed by Na+ and Fe2+ Exchanged Montmorillonites on Lemna minor

The toxicity of two pesticides, diazinon (DAZ) and atrazine (ATR), before and after montmorillonite-catalyzed ozonation was comparatively investigated on the duckweed Lemna minor. The results allowed demonstrating the role of clay-containing media in the evolution in time of pesticide negative impact on L. minor plants. Pesticides conversion exceeded 94% after 30 min of ozonation in the presence of both Na+ and Fe2+ exchanged montmorillonites. Toxicity testing using L. minor permitted us to evaluate the change in pesticide ecotoxicity. The plant growth inhibition involved excessive oxidative stress depending on the pesticide concentration, molecular structure, and degradation degree. Pesticide adsorption and/or conversion by ozonation on clay surfaces significantly reduced the toxicity towards L. minor plants, more particularly in the presence of Fe(II)-exchanged montmorillonite. The results showed a strong correlation between the pesticide toxicity towards L. minor and the level of reactive oxygen species, which was found to depend on the catalytic activity of the clay minerals, pesticide exposure time to ozone, and formation of harmful derivatives. These findings open promising prospects for developing a method to monitor pesticide ecotoxicity according to clay-containing host-media and exposure time to ambient factors.

Direct toxicity of the herbicide florasulam against Chlorella vulgaris: An integrated physiological and metabolomic analysis

Herbicides are the agents of choice for use in weed control; however, they can enter the aquatic environment, with potentially serious consequences for non-target organisms. Despite the possible deleterious effects, little information is available regarding the ecotoxicity of the herbicide florasulam toward aquatic organisms. Accordingly, in this study, we investigated the toxic effect of florasulam on the freshwater microalga Chlorella vulgaris and sought to identify the underlying mechanisms. For this, we employed a growth inhibition toxicity test, and then assessed the changes in physiological and metabolomic parameters, including photosynthetic pigment content, antioxidant system, intracellular structure and complexity, and metabolite levels. The results showed that treatment with florasulam for 96 h at the concentration of 2 mg/L, 2.84 mg/L, and 6 mg/L in medium significantly inhibited algal growth and photosynthetic pigment content. Moreover, the levels of reactive oxygen species were also increased, resulting in oxidative damage and the upregulation of the activities of several antioxidant enzymes. Transmission electron microscopic and flow cytometric analysis further demonstrated that exposure to florasulam (6 mg/L) for 96 h disrupted the cell structure of C. vulgaris, characterized by the loss of cell membrane integrity and alterations in cell morphology. Changes in amino acid metabolism, carbohydrate metabolism, and the antioxidant system were also observed and contributed to the suppressive effect of florasulam on the growth of this microalga. Our findings regarding the potential risks of florasulam in aquatic ecosystems provide a reference for the safe application of this herbicide in the environment.

Toxic effect of fluorene-9-bisphenol to green algae Chlorella vulgaris and its metabolic fate

Fluorene-9-bisphenol (BHPF), a bisphenol A (BPA) alternative, has recently attracted attention due to its wide use and potential toxicity. However, the toxic effects and fate of BHPF in freshwater algae remains to be elucidated. In this study, the impact of BHPF on Chlorella vulgaris was explored and the removal and bioaccumulation of BHPF by Chlorella vulgaris were investigated. Results showed that C. vulgaris was sensitive to BHPF at the concentration of >1 mg L-1, and lipid peroxidation was significantly increased under the exposure of >0.1 mg BHPF L-1. An oxidative stress was caused by BHPF, as the activities of superoxide dismutase (SOD) were significantly decreased in algal cells by >0.5 mg BHPF L-1. The removal rate of BHPF was significantly enhanced by the addition of algae. In addition, the increasing accumulation of BHPF in algae at concentrations ranging from 0.5 to 5 mg L-1 was observed and may contribute for the increased toxicity of BHPF to C. vulgaris. Ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) results demonstrated that three metabolites of BHPF were identified in algal cells, which may pose an unexpected effect in aquatic environment.

Biochemical responses of the freshwater microalga Dictyosphaerium sp. upon exposure to three sulfonamides

Sulfonamides (SAs) are common antimicrobial drugs, which are frequently detected in surface water systems, and are difficult to degrade, posing a potential threat to the aquatic environment. However, little is known about the potential adverse effects of SAs on non-target organisms (e.g., microalgae) in the aquatic ecosystem. In this study, the effect of SAs (sulfadiazine (SD), sulfamerazine (SM1), and sulfamethazine (SM2) at 1, 5, 20, and 50 mg/L concentrations, respectively) on the freshwater microalga Dictyosphaerium sp. was investigated, with respect to changes of biomass and chlorophyll a content and induction of extracellular polymer substances (EPS), including protein and polysaccharide contents. At the same time, the residue of SAs was determined. The results showed that Dictyosphaerium sp. was tolerant to the three SAs, and the chlorophyll a content in Dictyosphaerium sp. significantly decreased on day 7, followed by a "compensation phenomena". The increase in protein and polysaccharide contents played a defensive role in Dictyosphaerium sp. against antibiotic stress, and there was a strong positive correlation between polysaccharide contents and antibiotic concentrations. Dictyosphaerium sp. exhibited 35%-45%, 30%-42%, and 26%-51% removal of SD, SM1, and SM2, respectively. This study is helpful to understand the changes of EPS in the defense process of microalgae under the action of antibiotics, and provides a new insight for the ecological removal of antibiotic pollution in natural surface water system.

2D black phosphorus and tungsten trioxide heterojunction for enhancing photocatalytic performance in visible light

A novel, efficient and stable 2D black phosphorus and tungsten trioxide heterojunction (WO3-BPNs) was successfully synthesized using a combined hydrothermal, liquid phase exfoliating and co-precipitation method. The as-obtained WO3-BPNs composite was characterized by using XRD, SEM, XPS, UV-vis, etc. The results showed that the bandgap energy of the WO3-BPNs50 sample was 2.2 eV, which was lower than that of pure WO3. BPNs in the WO3-BPNs heterojunction as a co-catalyst effectively enhanced photo-generated electron-hole pairs separation. The synthesized WO3-BPNs sample significantly improved the photocatalytic performance in degrading rhodamine B (RhB) and metoprolol (MET) compared to pure WO3 and BPNs under visible-light. The maximum RhB and MET removal efficiencies were 92% and 87%, respectively, in the WO3-BPNs50 (added 50 mL BPNs dispersion) sample within 120 minutes. The relevant photocatalysis mechanisms were discussed. In addition, the intermediate products in the MET photodegradation process were investigated by LC-MS technology, and the degradation pathway of MET was proposed.

Short-term developmental toxicity and potential mechanisms of the herbicide metamifop to zebrafish (Danio rerio) embryos

Metamifop is a novel aryloxyphenoxy propionate (AOPP) herbicide that is widely applied in paddy fields, which will inevitably enter aquatic environments and pose a risk to aquatic organisms. However, the potential threat and toxicological mechanisms of metamifop in aquatic organisms are poorly understood. In this study, zebrafish embryos were used to investigate the potential developmental toxicity and mechanisms of metamifop. The results showed that metamifop exhibited high acute toxicity to zebrafish, with 96 h-LC₅₀ values of 0.648 and 0.216 mg/L to embryos and larvae of 72 h post-hatching (hph), respectively. Decreased body lengths, heartbeat number, and hatching rates, and increased malformation rates of embryos were observed after 96 h of exposure to 0.38 mg/L or higher concentration of metamifop. Furthermore, oxidative stress was caused in embryos, with increased contents of reactive oxygen species (ROS) and malondialdehyde (MDA), and altered activities of superoxide dismutase (SOD), catalase (CAT), and glutathione peroxidase (GPx). Metamifop exposure clearly triggered cell apoptosis in embryos, result in the increase of Caspase-3 and Caspase-9 activities and up-regulation of apoptosis-related genes (bax, p53, apaf1, caspase-3, and caspase-9). Additionally, the transcriptions of innate immune-related genes (il-8, il-1b, and ifn) were increased in the groups treated with 0.25 and 0.5 mg/L of metamifop. These results indicate that metamifop induced developmental toxicity in zebrafish, and the potential toxicological mechanisms were related to oxidative stress, cell apoptosis, and the innate immune responses in embryos.

Effect of Dibutyl Phthalate on the Tolerance and Lipid Accumulation in the Green Microalgae Chlorella vulgaris

In the present study, Chlorella vulgaris were cultured in the presence of the common plasticizer dibutyl phthalate (DBP) with different concentrations for 10 days. The cell density, DBP concentrations, neutral lipid concentrations, and lipid morphology in C. vulgaris were studied using optical microscopy, gas chromatography (GC), fluorescence spectrophotometry, and laser scanning confocal microscopy (LSCM). We observed that the neutral lipid contents and cell density of C. vulgaris were negatively influenced by DBP of high concentrations (50 and 100 mg/L), but significantly stimulated by DBP of low concentrations (5, 10, and 20 mg/L). Lipid bodies were destroyed into pieces by DBP of high concentrations (50 and 100 mg/L), but were slightly suppressed by DBP at low concentrations (5, 10, and 20 mg/L). Chlorella vulgaris treated with DBP (50 mg/L) for 2 days showed the highest removal efficiency (31.69%). The results suggested that C. vulgaris could be used in practice to remove DBP and has the potential of being oleaginous microalgae in DBP contaminated water.

Comparative performance of descriptors in a multiple linear and Kriging models: a case study on the acute toxicity of organic chemicals to algae

This study presents quantitative structure-toxicity relationship (QSTR) models on the toxicity of 91 organic compounds to Chlorella vulgaris using multiple linear regression (MLR) and Kriging techniques. The molecular descriptors were calculated using SPARTAN and DRAGON programs, and descriptor selection was made by "all subset" method available in the QSARINS software. MLR and Kriging models developed with the same descriptors were compared. In addition to these models, Kriging method was used for descriptor selection, and model development. The selected descriptors showed the importance of hydrophobicity, molecular weight and atomic ionization state in describing the toxicity of a diverse set of chemicals to C. vulgaris. A QSTR model should be associated with appropriate measures of goodness-of-fit, robustness, and predictivity in order to be used for regulatory purpose. Therefore, while the internal performances (goodness-of-fit and robustness) of the models were determined by using a training set, the predictive abilities of the models were determined by using a test set. The results of the study showed that while MLR method is easier to apply, the Kriging method was more successful in predicting toxicity.

The time-dependent hormetic effects of 1-alkyl-3-methylimidazolium chloride and their mixtures on Vibrio qinghaiensis sp. -Q67

The hormetic effects of ionic liquids (ILs) were paid more ecological attentions. However, the time-dependent hormetic effects of ILs and their mixtures remained to be studied. In this paper, the time-dependent toxicities of five single ILs, 1-ethyl-, 1-butyl-, 1-hexyl-, 1-octyl-, and 1-dodecyl-3-methylimidazolium chlorides (named as [C2mim]Cl, [C4mim]Cl, [C6mim]Cl, [C8mim]Cl, and [C12mim]Cl, respectively), and their five-component mixtures to Vibrio qinghaiensis sp.-Q67 were determined at five exposure time points. For single ILs, [C2mim]Cl displayed significant hormetic effects at 2, 4, 8, and 12h; and [C4mim]Cl exhibited significant hormetic effects at 4, 8 and 12h; while [C6mim]Cl, [C8mim]Cl and [C12mim]Cl have not significant hormetic effects. At the same time point, the longer the side chain is, the larger the inhibition at high concentration is, and the less the stimulation at low concentration is. Meanwhile, the maximum stimulation effects were found between 4 and 8h. All six IL mixtures designed by uniform design ray showed significant hormetic effects at 8 and 12h. By means of the variable selection and modeling method based on the prediction (VSMP), it was found that the higher the concentration of [C2mim]Cl is, the stronger the mixture hormetic effect is and the higher the concentration of [C12mim]Cl is, the weaker the hormetic effect is.

Ecotoxicological analysis of fly ash and rice-straw black carbon on Microcystis aeruginosa using flow cytometry

Black carbon (BC) has a strong affinity for hydrophobic organic compounds (HOCs), and it is a potential material to control HOCs pollution in aquatic ecosystems. Here, flow cytometry (FCM) was used to evaluate the ecotoxicological effect of fly ash, rice-straw ash, and their acid-demineralised products on the growth of Microcystis aeruginosa. It was found that the BCs had little negative effect on cyanobacteria, when the content of BCs was not above 1mgml(-1). However, higher doses of BCs (>2mgml(-1)) had an obvious negative effect on cell density and esterase activity, especially for BCs with acid treatment, which greatly inhibited cell density caused by its high adsorptivity for cyanobacteria. The BCs had little impact on the fluorescence intensity, only with a slight stimulation in later period, so the fluorescence intensity was a less sensitive indicator than cell density and esterase activity. Considering ecotoxicological effect of BCs on the algae, the application concentration of BCs for HOCs pollution control as in situ remediation material would better not exceed 1mgml(-1).

Time-dependent hormetic effects of 1-alkyl-3-methylimidazolium bromide on Vibrio qinghaiensis sp.-Q67: luminescence, redox reactants and antioxidases

The green credentials of ionic liquids (ILs) are being challenged due to the increasing evidence of their toxicity. The hormetic effects further raised their ecological concern. However, it remained poorly studied on the time-dependent changes of the hormetic effects and the mechanisms. In this study, we investigated the time-dependent hormetic effects of four 1-alkyl-3-methylimidazolium bromide ([amim]Br), including 1-ethyl ([emim]Br), -butyl ([bmim]Br), -hexyl ([hmim]Br) and -octyl ([omim]Br), on the luminescence of Vibrio qinghaiensis sp.-Q67. The results showed that [amim]Br with shorter side chains, [emim]Br and [bmim]Br, caused obvious hormetic time-dependent toxicities. The effective concentration (EC) values for the hormetic effects of [emim]Br and [bmim]Br increased with time. [amim]Br with longer side chains, [hmim]Br and [omim]Br, produced sigmoid concentration-dependent inhibitions on the luminescence, and the EC50 values almost unchanged. To illustrate the mechanism, we subsequently examined the responses of redox reactants and antioxidases. [emim]Br and [bmim]Br significantly induced FMN (flavin mononucleotide), NADH (reduced nicotinamide adenine dinucleotide), SOD (superoxide dismutase) and CAT (catalase), and the inductions increased with time, which is similar to the time-dependent changes of their hormetic effects on Q67. Meanwhile, [hmim]Br and [omim]Br did not cause significant effects on the redox reactants and antioxidases. In conclusion, the hormetic effects of [amim]Br on the luminescence, redox reactants and antioxidases showed the dependence on both exposure time and side chains. Our findings provided insights into the time-dependent biological process of the hormetic effects of [emim]Br and [bmim]Br on the photobacterium and its biochemical indicators.

Photocatalytic degradation of metoprolol tartrate in suspensions of two TiO2-based photocatalysts with different surface area. Identification of intermediates and proposal of degradation pathways

This study investigates the efficiency of the photocatalytic degradation of metoprolol tartrate (MET), a widely used β(1)-blocker, in TiO(2) suspensions of Wackherr's "Oxyde de titane standard" and Degussa P25. The study encompasses transformation kinetics and efficiency, identification of intermediates and reaction pathways. In the investigated range of initial concentrations (0.01-0.1 mM), the photocatalytic degradation of MET in the first stage of the reaction followed approximately a pseudo-first order kinetics. The TiO(2) Wackherr induced a significantly faster MET degradation compared to TiO(2) Degussa P25 when relatively high substrate concentrations were used. By examining the effect of ethanol as a scavenger of hydroxyl radicals (OH), it was shown that the reaction with OH played the main role in the photocatalytic degradation of MET. After 240 min of irradiation the reaction intermediates were almost completely mineralized to CO(2) and H(2)O, while the nitrogen was predominantly present as NH(4)(+). Reaction intermediates were studied in detail and a number of them were identified using LC-MS/MS (ESI+), which allowed the proposal of a tentative pathway for the photocatalytic transformation of MET as a function of the TiO(2) specimen.

Toxicity profile of labile preservative bronopol in water: the role of more persistent and toxic transformation products

Transformation products usually differ in environmental behaviors and toxicological properties from the parent contaminants, and probably cause potential risks to the environment. Toxicity evolution of a labile preservative, bronopol, upon primary aquatic degradation processes was investigated. Bronopol rapidly hydrolyzed in natural waters, and primarily produced more stable 2-bromo-2-nitroethanol (BNE) and bromonitromethane (BNM). Light enhanced degradation of the targeted compounds with water site specific photoactivity. The bond order analysis theoretically revealed that the reversible retroaldol reactions were primary degradation routes for bronopol and BNE. Judging from toxicity assays and the relative pesticide toxicity index, these degradation products (i.e., BNE and BNM), more persistent and higher toxic than the parent, probably accumulated in natural waters and resulted in higher or prolonging adverse impacts. Therefore, these transformation products should be included into the assessment of ecological risks of non-persistent and low toxic chemicals such as the preservative bronopol.

Comparative studies on the degradation of three aromatic compounds by Pseudomonas sp. and Staphylococcus xylosus

Biological methods of wastewater treatment have been proved very effective for bioremediation of polluted sites. In this study, the degrading abilities of two bacteria Pseudomonas sp. and Staphylococcus xylosus, towards 1,2-dichlorobenzene (1,2-DCB), 2,4-dichlorophenol (2,4-DCP) and 4-Cl-m-cresol, are compared. Culture history and the presence of glucose as carbon source have been used for the optimization of cell's performance. 1,2-DCB showed the higher values of effective concentration (EC(50)), 1.04 and 0.84 mM with Pseudomonas sp. and S. xylosus respectively, whereas no substrate-inhibition appeared, in contrary to 4-Cl-m-cresol, that was more persistent in biodegradation by both bacteria. 2,4-DCP was less assimilated compared to 1,2-DCB, whereas bacterial specificity was higher, as it was found by the estimation of the half-saturation constant of 0.36 and 0.26 mM with Pseudomonas sp. and S. xylosus, respectively.