Production of new cellulose nanomaterial from red algae marine biomass Gelidium elegans

Enhanced Total Contactless Photothermal Desalination by Translucent Thin Film Coating of Crystalline Nanocellulose

The innovative approach of harnessing abundant solar energy to facilitate water purification holds great potential for addressing a diverse range of water-related challenges. Utilizing the same method of photothermal desalination is highly promising, sustainable, and cost effective. However, in photothermal desalination, generally, steam is generated at the liquid-air interface. Despite its immense potential, this results in a lower evaporation rate and is prone to salt fouling. Therefore, to address two main challenges, (1) fouling and (2) maximum interfacial temperature (100 °C), here, we report total contactless photothermal desalination by a translucent thin film coating of Crystalline Nanocellulose (CNC). In contactless photothermal desalination, the active photothermal layer remains in no physical contact with the saline water; thus, automatic antifouling and a temperature above the boiling point of water can be achieved for water purification. In this report, we have sustainably extracted CNC from waste sawdust by a sonochemical extraction method using minimal chemicals. Additionally, the sonoextraction method through cavitation helps in the desulfation of CNC. These thermally stable and highly crystalline CNCs are used in making active translucent photothermal active layers for photothermal desalination. CNCs were well characterized by both microscopic and spectroscopic techniques. In the photothermal desalination, the results show an augmented evaporation rate of ∼3.30 kg/m2·h and virtually infinite recyclability for longer usability. Moreover, the integrated setup reported here comprises an independent module with a highly flexible design that mimics the greenhouse effect for a high solar-to-steam output.

From sea to sea: Edible, hydrostable, and degradable straws based on seaweed-derived insoluble cellulose fibers and soluble polysaccharides

The widespread use of disposable plastic straws has caused a long-lasting environmental problem. Potential alternatives for plastic straws are far from satisfactory due to the low utility, poor water stability, and non-ideal natural degradability. In this work, an edible, hydrostable, and degradable straw was developed from the economically significant seaweed. Seaweed-derived insoluble cellulose fibers were used as the building block of the straw, and the soluble polysaccharide extracts were explored as the natural glue through the chelation with Ca2+. Repeated freeze-thawing was introduced to strengthen the molecular interactions, which further improved its mechanical stability and hydrostability. The straw exhibited remarkable natural degradability in open environments, particularly in marine-mimicking conditions. By incorporating pH-sensitive food pigments, the straws could indicate acid-base property of a beverage or even discriminate the freshness of milk. The versatile seaweed-derived straw adhered to the biocycle concept of "from sea to sea" to alleviate the burden of white pollution on oceans.

Chitosan-grafted salicylaldehyde/algae composite for methyl violet dye removal: adsorption modeling and optimization

In this study, a hydrothermal approach was employed to graft chitosan (Chit)/algae (ALG) with salicylaldehyde (SA), resulting in the synthesis of a biocomposite named salicylaldehyde-based chitosan Schiff base/algae (Chit-SA/ALG). The main objective of this biocomposite was to effectively remove methyl violet (MV), an organic dye, from aqueous solutions. The adsorption performance of Chit-SA/ALG toward MV was investigated in detail, considering the effects of three factors: (A) Chit-SA/ALG dose (ranging from 0.02 to 0.1 g/100 mL), (B) pH (ranging from 4 to 10), and (C) time (ranging from 10 to 120 min). The Box-Behnken design (BBD) was utilized for experimental design and analysis. The experimental results exhibited a good fit with both the pseudo-second-order kinetic model and the Freundlich isotherm, suggesting their suitability for describing the MV adsorption process on Chit-SA/ALG. The maximum adsorption capacity of Chit-SA/ALG, as calculated by the Langmuir model, was found to be 115.6 mg/g. The remarkable adsorption of MV onto Chit-SA/ALG can be primarily attributed to the electrostatic forces between Chit-SA/ALG and MV as well as the involvement of various interactions such as n-π, π-π, and H-bond interactions. This research demonstrates that Chit-SA/ALG exhibits promising potential as a highly efficient adsorbent for the removal of organic dyes from water systems.

Development of nanocellulose hydrogels for application in the food and biomedical industries: A review

As the most abundant and renewable natural resource, cellulose has attracted significant attention and research interest for the production of hydrogels (HGs). To address environmental issues and emerging demands, the benefits of naturally produced HGs include excellent mechanical properties and superior biocompatibility. HGs are three-dimensional networks created by chemical or physical cross-linking of linear or branched hydrophilic polymers and have high capacity for absorption of water and biological fluids. Although widely used in the food and biomedical fields, most HGs are not biodegradable. Nanocellulose hydrogels (NC-HGs) have been extensively applied in the food industry for detection of freshness, chemical additives, and substitutes, as well as the biomedical field for use as bioengineering scaffolds and drug delivery systems owing to structural interchangeability and stimuli-responsive properties. In this review article, the sources, structures, and preparation methods of NC-HGs are described, applications in the food and biomedical industries are summarized, and current limitations and future trends are discussed.

Zinc Oxide Nanoparticles Alleviate Salt Stress in Cotton (Gossypium hirsutum L.) by Adjusting Na+/K+ Ratio and Antioxidative Ability

Soil salinization poses a threat to the sustainability of agricultural production and has become a global issue. Cotton is an important cash crop and plays an important role in economic development. Salt stress has been harming the yield and quality of many crops, including cotton, for many years. In recent years, soil salinization has been increasing. It is crucial to study the mechanism of cotton salt tolerance and explore diversified materials and methods to alleviate the salt stress of cotton for the development of the cotton industry. Nanoparticles (NPs) are an effective means to alleviate salt stress. In this study, zinc oxide NPs (ZnO NPs) were sprayed on cotton leaves with the aim of investigating the intrinsic mechanism of NPs to alleviate salt stress in cotton. The results show that the foliar spraying of ZnO NPs significantly alleviated the negative effects of salt stress on hydroponic cotton seedlings, including the improvement of above-ground and root dry and fresh weight, leaf area, seedling height, and stem diameter. In addition, ZnO NPs can significantly improve the salt-induced oxidative stress by reducing the levels of MDA, H2O2, and O2- and increasing the activities of major antioxidant enzymes, such as superoxide dismutase (SOD), peroxidase (POD), and catalase (CAT). Furthermore, RNA-seq showed that the foliar spraying of ZnO NPs could induce the expressions of CNGC, NHX2, AHA3, HAK17, and other genes, and reduce the expression of SKOR, combined with the CBL-CIPK pathway, which alleviated the toxic effect of excessive Na+ and reduced the loss of excessive K+ so that the Na+/K+ ratio was stabilized. In summary, our results indicate that the foliar application of ZnO NPs can alleviate high salt stress in cotton by adjusting the Na+/K+ ratio and regulating antioxidative ability. This provides a new strategy for alleviating the salt stress of cotton and other crops, which is conducive to the development of agriculture.

Synergistic antimicrobial action of nanocellulose, nanoselenium, and nanocomposite against pathogenic microorganisms

Recently, there has been a surge in curiosity regarding the application of biopolymer-derived nanomaterials, primarily attributable to their extensive array of potential applications. In this study, nanocellulose was extracted from algae, biomolecule substances synthesized selenium nanoparticles, and a simple nanocomposite of nanocellulose and nanoselenium was elaborated using nanocellulose as a reducing agent under hydrothermal conditions. These nanocomposite materials have markedly improved properties at low concentrations. Our obtained polymers were characterized using techniques including Fourier-transform infrared spectroscopy, X-ray powder diffraction, Thermo gravimetric analysis (TGA), Scanning electron microscopic (SEM), Energy Dispersive X-ray analysis (EDX), Transmission electron microscopic (TEM), Zeta Potential and Dynamic Light Scattering (DLS). The size of nanocellulose, nanoselenium, and nanocomposite ranged from 35 to 85 nm. Antimicrobial investigation of the prepared nanopolymers was tested against Gram-negative bacteria such as Bacillus subtilis ATCC 6633 and Staphylococcus aureus ATCC 6538, Gram-positive bacteria such as Escherichia coli ATCC8739 and Pseudomonas aeruginosa ATCC 90274 and fungi such as Candida albicans ATCC 10221 besides Aspergillus fumigatus. In antibacterial action tests, nanoselenium showed significant efficacy against Bacillus subtilis with a 12 mm zone of inhibition, while the nanocomposite eclipsed all microorganisms. Nanocellulose and the nanocomposite were potent against Staphylococcus aureus (14 mm and 16 mm zones of inhibition, respectively). The nanocomposite showed potential against Escherichia coli and Pseudomonas aeruginosa (17 mm and 15 mm zones of inhibition, respectively). All polymers effectively inhibited Candida albicans growth (18 mm for the nanocomposite). The minimum inhibitory concentrations (MIC) for three polymers have also been established. While nanocellulose displayed a MIC of 62.5 μg/ml in contradiction to Staphylococcus aureus, nanoselenium demonstrated a significant MIC of 3.95 μg/ml against Bacillus subtilis. These findings highlight the potential of the nanocomposite (nanocellulose-nanoselenium) as a broad-spectrum antimicrobial polymer.

Cellulose separation from ramie bone by one step process with green hydrogen peroxide-citric acid

Ramie bone (RB), an agricultural waste generated in the textile industry, is a vastly productive renewable natural resource with the potential to be used as a source of cellulose. In this study, ramie bone cellulose (RB-CE) was obtained in one step using a simple and ecologically friendly hydrogen peroxide-citric acid (HPCA) treatment procedure that avoided the use of halogenated reagents and strong acids while also streamlining the treatment processes. Various analytical methods were used to investigate the chemical composition and structure, crystallinity, morphology, thermal properties, surface area and hydration properties of cellulose separated at different treatment temperatures. HPCA successfully removed lignin and hemicellulose from RB, according to chemical composition analysis and FTIR. RB-CE had a type I cellulose crystal structure, and the crystallinity improved with increasing treatment temperature, reaching 72.51 % for RB-CE90. The RB-CE showed good thermal stability with degradation temperatures ranging from 294.2 °C to 319.1 °C. Furthermore, RB-CE had a high water/oil binding capacity, with RB-CE90 having WHC and OBC of 9.68 g/g and 7.24 g/g, respectively. The current work serves as a model for the environmentally friendly and convenient extraction of cellulose from biomass, and the cellulose obtained can be employed in the field of food and composite materials.

Caenorhabditis elegans endorse bacterial nanocellulose fibers as functional dietary Fiber reducing lipid markers

Bacterial nanocellulose (BNC) is a promising dietary fiber with potential as a functional food additive. We evaluated BNC fibers (BNCf) in the Caenorhabditis elegans model to obtain insight into the BNCf's biointeraction with its gastrointestinal tract while reducing the variables of higher complex animals. BNCf were uptaken and excreted by worms without crossing the intestinal barrier, confirming its biosafety regarding survival rate, reproduction, and aging for concentrations up to 34 μg/ml BNCf. However, a slight decrease in the worms' length was detected. A possible nutrient shortage or stress produced by BNCf was discarded by measuring stress and chemotactic response pathways. Besides, we detected a lipid-lowering effect of BNCf in N2 C. elegans in normal and high-caloric diets. Oxidative damage was computed in N2 worms and Rac1/ced-10 mutants. The GTPase Rac1 is involved in neurological diseases, where its dysregulation enhances ROS production and neuronal damage. BNCf reduced the lipid oxidative markers produced by ROS species in this worm strain. Finally, we detected that BNCf activated the genetic expression of the immunological response and lipid catabolic process. These results strengthen the use of BNCf as a functional dietary fiber and encourage the potential treatment of neurological disease by modulating diet.

Enhancing cationic dye removal via biocomposite formation between chitosan and food grade algae: Optimization of algae loading and adsorption parameters

Herein, a natural material including chitosan (CTS) and algae (food-grade algae, FGA) was exploited to attain a bio-adsorbent (CTS/FGA) for enhanced methyl violet 2B dye removal. A study of the FGA loading into CTS matrix showed that the best mixing ratio between CTS and FGA to be used for the MV 2B removal was 50 %:50 % (CTS/FGA; 50:50 w/w). The present study employed the Box-Behnken design (RSM-BBD) to investigate the impact of three processing factors, namely CTS/FGA-(50:50) dose (0.02-0.1 g/100 mL), pH of solution (4-10), and contact time (5-15 min) on the decolorization rate of MV 2B dye. The results obtained from the equilibrium and kinetic experiments indicate that the adsorption of MV 2B dye on CTS/FGA-(50:50) follows the Langmuir and pseudo-second-order models, respectively. The CTS/FGA exhibits an adsorption capacity of 179.8 mg/g. The characterization of CTS/FGA-(50:50) involves the proposed mechanism of MV 2B adsorption, which primarily encompasses various interactions such as electrostatic forces, n-π stacking, and H-bonding. The present study demonstrates that CTS/FGA-(50:50) synthesized material exhibits a distinctive structure and excellent adsorption properties, thereby providing a viable option for the elimination of toxic cationic dyes from polluted water.

High adsorptive performance of chitosan-microalgae-carbon-doped TiO2 (kronos)/ salicylaldehyde for brilliant green dye adsorption: Optimization and mechanistic approach

A composite of chitosan biopolymer with microalgae and commercial carbon-doped titanium dioxide (kronos) was modified by grafting an aromatic aldehyde (salicylaldehyde) in a hydrothermal process for the removal of brilliant green (BG) dye. The resulting Schiff's base Chitosan-Microalgae-TiO2 kronos/Salicylaldehyde (CsMaTk/S) material was characterised using various analytical methods (conclusive of physical properties using BET surface analysis method, elemental analysis, FTIR, SEM-EDX, XRD, XPS and point of zero charge). Box Behnken Design was utilised for the optimisation of the three input variables, i.e., adsorbent dose, pH of the media and contact time. The optimum conditions appointed by the optimisation process were further affirmed by the desirability test and employed in the equilibrium studies in batch mode and the results exhibited a better fit towards the pseudo-second-order kinetic model as well as Freundlich and Langmuir isotherm models, with a maximum adsorption capacity of 957.0 mg/g. Furthermore, the reusability study displayed the adsorptive performance of CsMaTk/S remains effective throughout five adsorption cycles. The possible interactions between the dye molecules and the surface of the adsorbent were derived based on the analyses performed and the electrostatic attractions, H-bonding, Yoshida-H bonding, π-π and n-π interactions are concluded to be the responsible forces in this adsorption process.

Upcycling Food By-products: Characteristics and Applications of Nanocellulose

Rising global food prices and the increasing prevalence of food insecurity highlight the imprudence of food waste and the inefficiencies of the current food system. Upcycling food by-products holds significant potential for mitigating food loss and waste within the food supply chain. Food by-products can be utilized to extract nanocellulose, a material that has obtained substantial attention recently due to its renewability, biocompatibility, bioavailability, and a multitude of remarkable properties. Cellulose nanomaterials have been the subject of extensive research and have shown promise across a wide array of applications, including the food industry. Notably, nanocellulose possesses unique attributes such as a surface area, aspect ratio, rheological behavior, water absorption capabilities, crystallinity, surface modification, as well as low possibilities of cytotoxicity and genotoxicity. These qualities make nanocellulose suitable for diverse applications spanning the realms of food production, biomedicine, packaging, and beyond. This review aims to provide an overview of the outcomes and potential applications of cellulose nanomaterials derived from food by-products. Nanocellulose can be produced through both top-down and bottom-up approaches, yielding various types of nanocellulose. Each of these variants possesses distinctive characteristics that have the potential to significantly enhance multiple sectors within the commercial market.

Cellulose nanocrystals extracted from rice husk using the formic/peroxyformic acid process: isolation and structural characterization

Cellulose derived from biomass is a renewable resource with numerous applications. Using formic/peroxyformic acid at atmospheric pressure, cellulose nanocrystals (CNC) were isolated from rice husk (RH) in this study. This method was an excellent way to get rid of lignin and hemicelluloses from RH. The cellulose was subsequently acid hydrolyzed by H2SO4 (64%) for 30 minutes at 45 °C. The chemical and microstructure analysis showed that the lignin and hemicellulose contents of raw RH had been eliminated, and the crystallinity content of CNC was 67.16%. According to transmission electron microscopy (TEM) morphological analysis, CNC measured 19 ± 3.3 nm in diameter, 195 ± 24 nm in length, and 10.2 ± 6.8 in aspect ratio. The thermal stability of RH and CNC was also investigated using thermogravimetric analysis (TGA). These encouraging findings demonstrated the potential for reusing RH agricultural waste to create CNC and include nanocomposites as a reinforcing material.

Exploring nanocellulose frontiers: A comprehensive review of its extraction, properties, and pioneering applications in the automotive and biomedical industries

Material is an inseparable entity for humans to serve different purposes. However, synthetic polymers represent a major category of anthropogenic pollutants with detrimental impacts on natural ecosystems. This escalating environmental issue is characterized by the accumulation of non-biodegradable plastic materials, which pose serious threats to the health of our planet's ecosystem. Cellulose is becoming a focal point for many researchers due to its high availability. It has been used to serve various purposes. Recent scientific advancements have unveiled innovative prospects for the utilization of nanocellulose within the area of advanced science. This comprehensive review investigates deeply into the field of nanocellulose, explaining the methodologies employed in separating nanocellulose from cellulose. It also explains upon two intricately examined applications that emphasize the pivotal role of nanocellulose in nanocomposites. The initial instance pertains to the automotive sector, encompassing cutting-edge applications in electric vehicle (EV) batteries, while the second exemplifies the use of nanocellulose in the field of biomedical applications like otorhinolaryngology, ophthalmology, and wound dressing. This review aims to provide comprehensive information starting from the definitions, identifying the sources of the nanocellulose and its extraction, and ending with the recent applications in the emerging field such as energy storage and biomedical applications.

Extraction and characterization of nanocellulose from cattail leaves: Morphological, microstructural and thermal properties

Hydrogen peroxide combined with acid treatment demonstrates its respective characteristics for the separation of lignocellulosic biomass. Herein, holocellulose was extracted from Cattail leaves (CL) by a two-step treatment with alkali and hydrogen peroxide-acetic acid (HPAA). Then carboxylated nanocellulose was hydrolyzed with a mixed organic/inorganic acid. The chemical composition of the holocellulose and the physicochemical properties of the separated carboxylated nanocellulose were comparable. Carboxyl groups were introduced on the nanocellulose as a result of the esterification process with citric acid (CA), which endows the nanocellulose with high thermal stability (315-318 °C) and good light transmission (>80 %). Furthermore, morphological analyses revealed that nanocellulose had a spider-web-like structure with diameter between 5 and 20 nm.

Different nanocellulose morphologies (cellulose nanofibers, nanocrystals and nanospheres) extracted from Sunn hemp (Crotalaria Juncea)

Nanocellulose of different morphologies was extracted from Sunn Hemp (Crotalaria Juncea) using acid hydrolysis. The work focused on two objectives: first, to valorize the Sunn Hemp fibers for nanocellulose (NC) production, and second, to study the effects of acid concentration on different morphologies of NC and their properties. The study extracted nanocellulose at five different concentrations of H2SO4: 16 %, 32 %, 48 %, 64 %, and 72 %. Obtained nanocellulose was characterized by Scanning Electron Microscopy (FE-SEM), Atomic Force Microscopy (AFM), Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD) and Thermogravimetric Analysis (TGA). AFM and FE-SEM confirmed the production of three different morphologies of nanocellulose. The NC-32 had a web-like structure typically observed for cellulose nanofibrils (CNF), whereas NC-48 and NC-64 were observed as cellulose nanocrystals (CNC) with rod-like and needle-like shapes, respectively, and NC-72 displayed spherical particles termed cellulose nanospheres (CNS). The total crystallinity index of NC was calculated using FTIR, and a similar trend of crystallinity was also observed from XRD analysis. NC-32 was obtained with the highest yield of 94.83 %, followed by 91.40 % and 81.70 % for NC-48 and NC-64, respectively, whereas NC-72 yielded the lowest yield of 12.03 %. NC-72 had the highest thermal stability among other NC morphologies.

Low-Frequency Ultrasound Effects on Cellulose Nanocrystals for Potential Application in Stabilizing Pickering Emulsions

Cellulose, in the form of cellulose nanocrystals (CNCs), is a promising biomaterial for stabilizing Pickering emulsions (PEs). PEs are commonly formed using low-frequency ultrasound (LFU) treatment and impact CNC properties. The present study investigated the specific effects of LFU treatment on CNCs' chemical and physical properties. CNCs were characterized using dynamic light scattering, ζ;-potential determination, Fourier transform infrared spectroscopy, X-ray diffraction, and contact angle measurement. CNC suspensions were studied using rheological analysis and static multiple light scattering. LFU treatment broke CNC aggregates and modified the rheological behavior of CNC suspensions but did not affect the CNCs' chemical or crystallographic structures, surface charge, or hydrophilic properties. During the storage of CNC suspensions and PEs, liquid crystal formation was observed with cross-polarized light. Hypotheses related to the impact of liquid crystal CNCs on PE stability were proposed.

Bacterial cellulose: Nature's greener tool for industries

Bacteria are considered mini chemical factories that help us in providing a wide range of products for various purposes. These days, bacterial cellulose (BC) is getting attention by researchers due to its quality, eco-friendly nature, and excellent physical-mechanical qualities. It is being used in the fabrication of nanocomposites. Its nanocomposites can be used in various industries, including medicine, food, leather, textiles, environment, electronics, and cosmetics. This area of research is emerging and still in its infancy stage, as new applications are still coming up. Most of the work on BC has been done during the last two decades and serious inputs are required in this direction in order to make the production process commercially viable and ultimately the application part. Biowastes, such as fruits and vegetables wastes, can be used as a cost-effective medium to minimize the cost for large-scale production of BC-based nanocomposites thus will valorize the biowaste material into a valuable product. Using biowaste as media will also aid in better waste management along with reduction in detrimental environmental effects. This review will help the readers to understand the potential applications of BC and its nanocomposites as well as their vital role in our daily lives.

Food-grade algae modified Schiff base-chitosan benzaldehyde composite for cationic methyl violet 2B dye removal: RSM statistical parametric optimization

This work aims to apply the use of food-grade algae (FGA) composited with chitosan-benzaldehyde Schiff base biopolymer (CHA-BD) as a new adsorbent (CHA-BA/FGA) for methyl violet 2B (MV 2B) dye removal from aqueous solutions. The effect of three processing variables, including CHA-BA/FGA dosage (0.02-0.1 g/100 mL), pH solution (4-10), and contact duration (10-120 min) on the removal of MV 2B was investigated using the Box-Behnken design (BBD) model. Kinetic and equilibrium dye adsorption profiles reveal that the uptake of MV 2B dye by CHA-BA/FGA is described by the pseudo-second kinetics and the Langmuir models. The thermodynamics of the adsorption process (ΔG°, ΔH°, and ΔS°) reveal spontaneous and favorable adsorption parameters of MV 2B dye onto the CHA-BA/FGA biocomposite at ambient conditions. The CHA-BA/FGA exhibited the maximum ability to absorb MV 2B of 126.51 mg/g (operating conditions: CHA-BA/FGA dose = 0.09 g/100 mL, solution pH = 8.68, and temperature = 25 °C). Various interactions, including H-bonding, electrostatic forces, π-π stacking, and n-π stacking provide an account of the hypothesized mechanism of MV 2B adsorption onto the surface of CHA-BA/FGA. This research reveals that CHA-BA/FGA with its unique biocomposite structure and favorable adsorption properties can be used to remove harmful cationic dyes from wastewater.

Preparation of Nanocellulose from Coffee Pulp and Its Potential as a Polymer Reinforcement

Coffee is one of the most valued agricultural products regarding its high commercialization rate. During the production of coffee beans, coffee pulp is obtained as one of the main byproducts with a cellulose content of more than 30% of dry weight. This research focused on the value-added potential of coffee pulp fiber as the reinforcement in composite materials. The nanocellulose coffee pulp (NCP) from the coffee pulp (CP) was prepared and subsequently used as a filler to reinforce the polyvinyl alcohol (PVA) matrix for the improvement of PVA composite properties. The CP was treated via alkali and bleaching treatment before the production of NCP using the acid hydrolysis treatment. The TEM result of NCP showed the successful preparation of NCP with an average diameter of 16.03 ± 4.70 nm with increasing crystallinity size and crystallinity index. The effect of glycerol (G) in the PVA matrix was observed. The result showed that glycerol had a play-role as a plasticizer for increased flexibility and decreased hardness and brittleness of PVA nanocomposite film. The nanocomposite film of PVA/G/NCP was fabricated with various ratios of NCP through the casting method. It was shown that the physical properties were improved with the presence of NCP in the PVA matrix compared to the neat PVA film.

Biosynthesis of cellulose from Ulva lactuca, manufacture of nanocellulose and its application as antimicrobial polymer

Green nanotechnology has recently been recognized as a more proper and safer tool for medical applications thanks to its natural reductions with low toxicity and avoidance of injurious chemicals. The macroalgal biomass was used for nanocellulose biosynthesis. Algae are abundant in the environment and have a high content of cellulose. In our study, we extracted parent cellulose from Ulva lactuca where consecutive treatments extracted cellulose to obtain an insoluble fraction rich in cellulose. The extracted cellulose has the same results obtained by matching it with reference cellulose, especially the same Fourier transform infrared (FTIR) and X-Ray diffraction (XRD) analysis peaks. Nanocellulose was synthesized from extracted cellulose with hydrolysis by sulfuric acid. Nanocellulose was examined by Scanning electron microscope (SEM) shown by a slab-like region as Fig. 4a and Energy dispersive X-ray (EDX) to examine the chemical composition. The size of nanocellulose in the range of 50 nm is calculated by XRD analysis. Antibacterial examination of nanocellulose was tested against Gram+ bacteria like Staphylococcus aureus (ATCC6538), Klebsiella pneumonia (ST627), and Gram-negative bacteria such as Escherichia coli (ATCC25922), and coagulase-negative Staphylococci (CoNS) to give 4.06, 4.66, 4.93 and 4.43 cm as respectively. Comparing the antibacterial effect of nanocellulose with some antibiotics and estimating minimal Inhibitory Concentration (MIC) of nanocellulose. We tested the influence of cellulose and nanocellulose on some fungi such as Aspergillus flavus, Candida albicans, and Candida tropicalis. These results demonstrate that nanocellulose could be developed as an excellent solution to these challenges, making nanocellulose extracted from natural algae a very important medical material that is compatible with sustainable development.

Insight into the Latest Medical Applications of Nanocellulose

Nanocelluloses (NCs) are appealing nanomaterials that have experienced rapid development in recent years, with great potential in the biomedical field. This trend aligns with the increasing demand for sustainable materials, which will contribute both to an improvement in wellbeing and an extension of human life, and with the demand to keep up with advances in medical technology. In recent years, due to the diversity of their physical and biological properties and the possibility of tuning them according to the desired goal, these nanomaterials represent a point of maximum interest in the medical field. Applications such as tissue engineering, drug delivery, wound dressing, medical implants or those in cardiovascular health are some of the applications in which NCs have been successfully used. This review presents insight into the latest medical applications of NCs, in the forms of cellulose nanocrystals (CNCs), cellulose nanofibers (CNFs) and bacterial nanocellulose (BNC), with an emphasis on the domains that have recently experienced remarkable growth, namely wound dressing, tissue engineering and drug delivery. In order to highlight only the most recent achievements, the presented information is focused on studies from the last 3 years. Approaches to the preparation of NCs are discussed either by top-down (chemical or mechanical degradation) or by bottom-up (biosynthesis) techniques, along with their morphological characterization and unique properties, such as mechanical and biological properties. Finally, the main challenges, limitations and future research directions of NCs are identified in a sustained effort to identify their effective use in biomedical fields.

Dinoflagellates as sustainable cellulose source: Cultivation, extraction, and characterization

The global demand for manufacturing and consuming biodegradable materials from natural sources has created a great interest in microalgae, such as dinoflagellates. Photosynthetic dinoflagellates are a sustainable source of natural materials such as cellulose as they grow using only sunlight and CO₂ at near-neutral pH without any fertilizers. In this paper, the cultivation of two species of dinoflagellates (Peridinium sp. and Prorocentrum micans) is established under lab conditions (up to 20 l), cellulose extraction is optimized, and the resulting material is thoroughly characterized. Dinoflagellate cellulose was extracted at room temperature by sequential treatment with highly concentrated 30 % NaOH and 6 M HCl, followed by bleaching with 10 % H₂O₂. The overall yield of cellulose is around 73 % (w/w), and roughly 85 % of the original dinoflagellate cellulosic morphology remains intact. Chemical purity, morphology, and porosity of the dinoflagellate-derived cellulose are analysed by different characterization techniques (ICP-OES, SEM, XRD, ATR-FTIR, Raman, NMR, TGA, BET, and GPC). XRD characterization of the extracted cellulose shows characteristic reflexes corresponding to a cellulose II allomorph which is mainly amorphous. This result is further supported by ATR-FTIR, Raman, and NMR spectroscopy. Overall, these results show that the extracted cellulose is a highly porous, lignin-free material that is thermally stable up to 260 °C. Its high degree of purity and porosity make dinoflagellate-derived cellulose a promising, sustainable candidate for the development of functional hybrid materials for biomedical applications.

Residual Chlorella-Based Cellulose Nanofibers and Their Quaternization Modification and Efficient Anionic Dye Adsorption

Dye is an anionic common pollutant in industrial wastewater and poses a great threat to the environment and human health. Owing to its advantageous adsorption capacity, nanocellulose is widely used for wastewater treatment. The cell walls of Chlorella mainly comprise cellulose instead of lignin. In this study, residual Chlorella-based cellulose nanofiber (CNF) and cationic cellulose nanofiber (CCNF) with surface quaternization were prepared through homogenization. Moreover, Congo red (CR) was used as a model dye to measure the adsorption capacity of CNF and CCNF. The adsorption capacity was almost saturated when CNF and CCNF contacted CR for 100 min, and the adsorption kinetics coincided with the pseudo-secondary kinetics model. The initial concentration of CR considerably affected its adsorption on CNF and CCNF. Below the initial concentration of 40 mg/g, the adsorption on CNF and CCNF considerably increased with the increase in the initial concentration of CR. Based on the sorption isotherms analysis of CNF and CCNF, the Langmuir model fitted best with the experimental data. Thus, CNF and CCNF surfaces were uniform, and monolayer adsorption occurred. The adsorption of CR on CNF and CCNF was greatly affected by the pH value, and the acidic medium favored the adsorption of CR (especially for CCNF). CCNF showed a more advantageous adsorption capacity, with a maximum value of 1657.89 mg/g, compared to that of CNF (190.0 mg/g). According to the findings of this study, residual Chlorella-based CCNF could be a very promising adsorbent candidate for removing anionic dyes from wastewater.

Bacterial Cellulose-Based Materials: A Perspective on Cardiovascular Tissue Engineering Applications

Today, a wide variety of bio- and nanomaterials have been deployed for cardiovascular tissue engineering (TE), including polymers, metal oxides, graphene/its derivatives, organometallic complexes/composites based on inorganic-organic components, among others. Despite several advantages of these materials with unique mechanical, biological, and electrical properties, some challenges still remain pertaining to their biocompatibility, cytocompatibility, and possible risk factors (e.g., teratogenicity or carcinogenicity), restricting their future clinical applications. Natural polysaccharide- and protein-based (nano)structures with the benefits of biocompatibility, sustainability, biodegradability, and versatility have been exploited in the field of cardiovascular TE focusing on targeted drug delivery, vascular grafts, engineered cardiac muscle, etc. The usage of these natural biomaterials and their residues offers several advantages in terms of environmental aspects such as alleviating emission of greenhouse gases as well as the production of energy as a biomass consumption output. In TE, the development of biodegradable and biocompatible scaffolds with potentially three-dimensional structures, high porosity, and suitable cellular attachment/adhesion still needs to be comprehensively studied. In this context, bacterial cellulose (BC) with high purity, porosity, crystallinity, unique mechanical properties, biocompatibility, high water retention, and excellent elasticity can be considered as promising candidate for cardiovascular TE. However, several challenges/limitations regarding the absence of antimicrobial factors and degradability along with the low yield of production and extensive cultivation times (in large-scale production) still need to be resolved using suitable hybridization/modification strategies and optimization of conditions. The biocompatibility and bioactivity of BC-based materials along with their thermal, mechanical, and chemical stability are crucial aspects in designing TE scaffolds. Herein, cardiovascular TE applications of BC-based materials are deliberated, with a focus on the most recent advancements, important challenges, and future perspectives. Other biomaterials with cardiovascular TE applications and important roles of green nanotechnology in this field of science are covered to better compare and comprehensively review the subject. The application of BC-based materials and the collective roles of such biomaterials in the assembly of sustainable and natural-based scaffolds for cardiovascular TE are discussed.

Nanoencapsulation of oregano essential oil using cellulose nanocrystals extracted from hazelnut shell to enhance shelf life of fruits: Case study: Pears

This study aimed to investigate the potential application of cellulose nanocrystals (CNCs) extracted from an agricultural waste for encapsulation of oregano essential oil (OEO) and subsequently their use for coating to improve the shelf life of pears as a model. By hydrolyzing hazelnut shell cellulose under the optimum conditions, high crystalline CNCs with a zeta potential of -67.8 ± 4.4 mV and a diameter of 157 ± 10 nm were produced. Different concentrations of OEO (10-50 % w/w) were incorporated into CNCs and characterized using FTIR, XRD, SEM and TEM. OEO containing 50 % CNC with the highest EE and LC was selected for coating. Pears were coated with gluten containing 0.5, 1.5 and 2 % encapsulated OEO (EOEO) and pure OEO and stored for 28 days. Physicochemical, microbial and sensory properties of the pears were examined. Microbial analysis showed that EOEO2% was more effective in controlling microbial growth than controls and pure OEO, and a 1.09 Log reduction in bacterial count was recorded on day 28 of storage when compared to control. It was concluded that CNCs produced from an agricultural waste and loaded on an essential oil could be used to extend the shelf life of pear and potentially other fruits.

Low-cost biosorption of Fe(II) and Fe(III) from single and binary solutions using Ulva lactuca-derived cellulose nanocrystals-graphene oxide composite film

The marine algal biomass of Ulva lactuca was utilized for the extraction of cellulose and the development of cellulose nanocrystals/graphene oxide film. Cellulose nanocrystals with 50-150 nm were produced by H₂SO₄ hydrolysis of the algal cellulose. The adsorption efficiency of the nanocomposite film for Fe(II) and Fe(III) ions was successfully evaluated using Box-Behnken design. The maximum removal for Fe(II) (64.15%) could be attained at pH 5.13, adsorbent dosage 7.93 g L^-1 and Fe(II) concentration 15.39 mg L^-1, while the biosorption of Fe(III) was 69.92% at pH 5.0, adsorbent dosage 2 g L^-1, and Fe(III) concentration 15.0 mg L^-1. However, in the binary system, the removal efficiency of Fe(II) was enhanced to 95.48% at Fe(II):Fe(III) ratio of 1:1, while the Fe(III) removal was increased to 79.17% at ratio 1:2. The pseudo-second-order kinetics exhibited better fitting to the experimental results of Fe(II) and Fe(III) adsorption in both single and binary systems. The intra-particle diffusion was prominent during the biosorption, but the effect of the external mass transfer was significant. The Langmuir, Freundlich, Langmuir-Freundlich, Temkin, and Dubinin-Radushkevich isotherms showed satisfactory fitting to the experimental data, but they differ in priority based on iron state and pH. The adsorption of Fe(II) in the presence of Fe(III) in a mixture was best represented by the extended Langmuir model, while the extended Langmuir-Freundlich model best fitted the adsorption of Fe(III). The FT-IR analysis indicated that physisorption through electrostatic interaction/complexation is the predominant mechanism for the adsorption of iron using the nanocomposite film.

Preparation of microcrystalline cellulose from agricultural residues and their application as polylactic acid/microcrystalline cellulose composite films for the preservation of Lanzhou lily

Microcrystalline celluloses were isolated from four agricultural residues, including sweet sorghum stalk, Jerusalem artichoke stalk, grains stillage, and Chinese herb residue, and characterized in terms of physicochemical and structural properties. The obtained microcrystalline celluloses were composited with polylactic acid as a packing film for the preservation of Lanzhou lily. All the agricultural residues-derived microcrystalline celluloses were in cellulose I_β structure with high purity and good thermal stability. Microcrystalline celluloses from sweet sorghum stalk had a higher degree of polymerization (327) and crystallinity (70.52 %) than others. The preservation effect of lily bulbs packaged by films were significantly improved indicated by the lessened weight loss rate and the meliorative hardness and whiteness, which ascribe to the repressed oxidation reactions. Polylactic acid/microcrystalline cellulose composite films prepared from sweet sorghum straw have been proved the most effective. This work could offer a value-added outlet for agricultural residues to produce microcrystalline celluloses-based biocompatible films for preservation of Lanzhou lily.

Nanotechnology - A new frontier of nano-farming in agricultural and food production and its development

The potential of nanotechnology for the development of sustainable agriculture has been promising. The initiatives to meet the rising food needs of the rapidly growing world population are mainly powered by sustainable agriculture. Nanoparticles are used in agriculture due to their distinct physicochemical characteristics. The interaction of nanomaterials with soil components is strongly determined in terms of soil quality and plant growth. Numerous research has been carried out to investigate how nanoparticles affect the growth and development of plants. Nanotechnology has been applied to improve the quality and reduce post-harvest loss of agricultural products by extending their shelf life, particularly for fruits and vegetables. This review assesses the latest literature on nanotechnology, which is used as a nano-biofertilizer as seen in the agricultural field for high productivity and better growth of plants, an important source of balanced nutrition for the crop, seed germination, and quality enrichment. Additionally, post-harvest food processing and packaging can benefit greatly from the use of nanotechnology to cut down on food waste and contamination. It also critically discusses the mechanisms involved in nanoparticle absorption and translocation within the plants and the synthesis of green nanoparticles.

Ultrastrong, Thermally Stable, and Food-Safe Seaweed-Based Structural Material for Tableware

Widely used disposable plastic tableware is usually buried or directly discharged into the natural environment after using, which poses potential threats to the natural environment and human health. To solve this problem, nondegradable plastic tableware needs to be replaced by tableware composed of biodegradable structural materials with both food safety and the excellent mechanical and thermal properties. Here, a food-safe sargassum cellulose nanofiber (SCNF) is extracted from common seaweed in an efficient and low energy consuming way under mild reaction conditions. Then, by assembling the SCNF into a dense bulk material, a strong sargassum cellulose nanofiber structural material (SCNSM) with high strength (283 MPa) and high thermal stability (>160 °C) can be prepared. The SCNSM also possesses good machinability, which can be processed into tableware with different shapes, e.g., knives and forks. The overall performance of the SCNSM-based tableware is better than commercial plastic, wood-based, and poly(lactic acid) tableware, which shows great application potential in the tableware field.

Preparation of High-Solid Microfibrillated Cellulose from Gelidium amansii and Characterization of Its Physiochemical and Biological Properties

Microfibrillated cellulose (MFC) is a valuable material with wide industrial applications, particularly for the food and cosmetics industries, owing to its excellent physiochemical properties. Here, we prepared high-solid microfibrillated cellulose (HMFC) from the centrifugation of Gelidium amansii-derived MFC right after fibrillation. Dispersion properties, morphology, and structural changes were monitored during processing. HMFC has a five-fold higher solid concentration than MFC without significant changes to dispersion properties. SEM images and FTIR spectra of HMFC revealed a stable surface and structure against centrifugal forces. HMFC exhibited 2,2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) radical scavenging activity, although it could not scavenge 2,2-diphenyl-1-picrylhydrazyl (DPPH). Moreover, HMFC inhibited the generation of LPS-induced excessive nitrite and radial oxygen species in murine macrophage RAW264.7 cells. Additionally, HMFC suppressed LPS-induced Keap-1 expression in the cytosol but did not alter iNOS expression. HMFC also attenuated the UVB-induced phosphorylation of p38, c-Jun N-terminal kinase (JNK) 1/2, and extracellular-signal-regulated kinase (ERK) 1/2, as well as the phosphorylation of c-Jun in the immortalized human skin keratinocyte HaCaT cells. Therefore, the application of centrifugation is suitable for producing high-solid MFC as a candidate material for anti-inflammatory and anti-oxidative marine cosmeceuticals.

Role of Nanoparticles in Enhancing Crop Tolerance to Abiotic Stress: A Comprehensive Review

Plants are subjected to a wide range of abiotic stresses, such as heat, cold, drought, salinity, flooding, and heavy metals. Generally, abiotic stresses have adverse impacts on plant growth and development which affects agricultural productivity, causing food security problems, and resulting in economic losses. To reduce the negative effects of environmental stress on crop plants, novel technologies, such as nanotechnology, have emerged. Implementing nanotechnology in modern agriculture can also help improve the efficiency of water usage, prevent plant diseases, ensure food security, reduce environmental pollution, and enhance sustainability. In this regard, nanoparticles (NPs) can help combat nutrient deficiencies, promote stress tolerance, and improve the yield and quality of crops. This can be achieved by stimulating the activity of certain enzymes, increasing the contents (e.g., chlorophyll) and efficiency of photosynthesis, and controlling plant pathogens. The use of nanoscale agrochemicals, including nanopesticides, nanoherbicides, and nanofertilizers, has recently acquired increasing interest as potential plant-enhancing technologies. This review acknowledges the positive impacts of NPs in sustainable agriculture, and highlights their adverse effects on the environment, health, and food chain. Here, the role and scope of NPs as a practical tool to enhance yield and mitigate the detrimental effects of abiotic stresses in crops are described. The future perspective of nanoparticles in agriculture has also been discussed.

Effect of the Addition of Corn Husk Cellulose Nanocrystals in the Development of a Novel Edible Film

The cellulose from agroindustrial waste can be treated and converted into nanocrystals or nanofibers. It could be used to produce biodegradable and edible films, contributing to the circular economy and being environmentally friendly. This research aimed to develop an edible film elaborated with activated cellulose nanocrystals, native potato starch, and glycerin. The activated cellulose nanocrystals were obtained by basic/acid digestion and esterification with citric acid from corn husks. The starch was extracted from the native potato cultivated at 3500 m of altitude. Four film formulations were elaborated with potato starch (2.6 to 4.4%), cellulose nanocrystals (0.0 to 0.12%), and glycerin (3.0 to 4.2%), by thermoforming at 60 °C. It was observed that the cellulose nanocrystals reported an average size of 676.0 nm. The films mainly present hydroxyl, carbonyl, and carboxyl groups that stabilize the polymeric matrix. It was observed that the addition of cellulose nanocrystals in the films significantly increased (p-value < 0.05) water activity (0.409 to 0.447), whiteness index (96.92 to 97.27), and organic carbon content. In opposition to gelatinization temperature (156.7 to 150.1 °C), transparency (6.69 to 6.17), resistance to traction (22.29 to 14.33 N/mm), and solubility in acidic, basic, ethanol, and water media decreased. However, no significant differences were observed in the thermal decomposition of the films evaluated through TGA analysis. The addition of cellulose nanocrystals in the films gives it good mechanical and thermal resistance qualities, with low solubility, making it a potential food-coating material.

Biological Synthesis of Silver Nanoparticles and Prospects in Plant Disease Management

Exploration of nanoparticles (NPs) for various biological and environmental applications has become one of the most important attributes of nanotechnology. Due to remarkable physicochemical properties, silver nanoparticles (AgNPs) are the most explored and used NPs in wide-ranging applications. Also, they have proven to be of high commercial use since they possess great chemical stability, conductivity, catalytic activity, and antimicrobial potential. Though several methods including chemical and physical methods have been devised, biological approaches using organisms such as bacteria, fungi, and plants have emerged as economical, safe, and effective alternatives for the biosynthesis of AgNPs. Recent studies highlight the potential of AgNPs in modern agricultural practices to control the growth and spread of infectious pathogenic microorganisms since the introduction of AgNPs effectively reduces plant diseases caused by a spectrum of bacteria and fungi. In this review, we highlight the biosynthesis of AgNPs and discuss their applications in plant disease management with recent examples. It is proposed that AgNPs are prospective NPs for the successful inhibition of pathogen growth and plant disease management. This review gives a better understanding of new biological approaches for AgNP synthesis and modes of their optimized applications that could contribute to sustainable agriculture.

Formulation of Novel Composite (Activated Nanoclay/Hydrocolloid of Nostoc sphaericum) and Its Application in the Removal of Heavy Metals from Wastewater

The removal of heavy metals from wastewater is an environmental challenge which demands the use of environmentally friendly materials that promote a circular economy. This study aimed to apply a novel composite of an activated nanoclay/hydrocolloid in the removal of heavy metals from wastewater. A composite blended under pressure was prepared with spray-dried hydrocolloid derived from Nostoc sphaericum algae and activated nanoclay in an acid medium and 1M NaCl. The composite and components were analyzed through infrared (IR), X-ray (XR), ζ potential, cation exchange capacity (CEC), particle size, and SEM images. The composite was subjected to the adsorption of heavy metals (Pb, As, Zn, and Cd) at pH 4.5 and the removal percentage, kinetics, and adsorption isotherms were evaluated. It was observed that the activated nanoclay and the composite that presented a particle size of around 400 nm significantly increased (p-value < 0.05) the CEC, ζ potential, the functional groups, and chelating components, removing heavy metals above 99% for Pb, As 33%, Cd 15%, and Zn 10%. Adsorption kinetics was adjusted to the pseudo second-order model (R2 > 0.98), and the Langmuir and Freundlich models better represented the sorption isotherm at 20 °C. The formulated composite presents a good ability to remove heavy metals in wastewater.

Enteromorpha cellulose micro-nanofibrils/poly(vinyl alcohol) based composite films with excellent hydrophilic, mechanical properties and improved thermal stability

This study presents the preparation of cellulose micro-nanofibrils (CMNFs) from Enteromorpha (EP) and the application in PVA/acetylated distarch phosphate (ADSP)/CMNFs composite films. The Micro-nano scale, hydrophilicity, and strong hydrogen bond characteristics of CMNFs prepared form EP by acid hydrolysis were confirmed through the granular statistics, XRD analysis and chemical structure analysis. With the addition of CMNFs, the ultimate tensile strength and elongation at break of composite films are increased by 42.4 % and 90.3 %. An original Weibull statistical analysis shows the impact of CMNFs' added amount on strength distribution and ultimate stress. SEM and polarizing microscope images show the CMNFs' dispersion state in that films is optimal, when their addition was to be 2 %-3 % of total dry weight of PVA/ADSP matrix， which is consistent with the results of Weibull modulus analysis. The main thermal weight-loss process of the composite film is divided into four stages, CMNFs can significantly increase the thermostability at 280 °C to 400 °C. The experiment of water contact angle and water vapor transmission rate of the composite films confirmed that CMNFs can improve films' hydrophilicity. This study provides basis for the preparation of hydrophilic CMNFs and mechanism of modification study PVA-based composites.

Facile synthesis of nanomaterials as nanofertilizers: a novel way for sustainable crop production

Nutrient fertilization plays a major role in improving crop productivity and maintaining soil fertility. In the last few decades, the productivity of current agricultural practices highly depends on the use of chemical fertilizers. Major drawback of traditional fertilizers is their low crop nutrient use efficiency and high loss into water. Nanomaterial in agriculture is a multipurpose tool for increasing growth, development, and yield of plants. Nanotechnology facilitates the amplifying of agriculture production by reducing relevant losses and improving the input efficiency. Nanotechnology has emerged as an attractive field of research and has various agriculture applications, especially the use of nano-agrochemicals to increase nutrient use efficiency and agricultural yield. Nanofertilizers are more effective as compared to chemical fertilizers due to their cost-efficient, eco-friendly, non-toxic, and more stable in nature. Overall, this chapter focuses on synthesis of nanofertilizers through physical, chemical, and biological methods. This chapter will also explore the use of nano-enabled fertilizers to enhance the nutrient use efficiency for sustainable crop production, and global food safety.

Investigation of the Structural, Thermal, and Physicochemical Properties of Nanocelluloses Extracted From Bamboo Shoot Processing Byproducts

Nanocellulose has gained increasing interest due to its excellent properties and great potential as a functional component or carrier in food and pharmaceutical industries. This study investigated the structural, thermal, and physicochemical properties of nanofibrillated cellulose (NFC) and nanocrystalline cellulose (CNC) extracted from bamboo shoot (Leleba oldhami Nakal) processing byproducts. NFCs were prepared through low concentration acid hydrolysis combined with ultrasonic treatment. CNCs were further isolated from NFCs using sulfuric acid hydrolysis treatment. TEM images showed that NFC and CNC exhibited typical long-chain and needle-like structures, respectively. CNC suspension was stable due to its zeta potential of -34.3 ± 1.23 mV. As expected, both NFC and CNC displayed high crystallinity indexes of 68.51 and 78.87%, and FTIR analysis confirmed the successful removal of lignin and hemicellulose during the treatments. However, the thermogravimetric analysis indicated that sulfuric acid hydrolysis decreased the thermal stability of CNCs. The improved physicochemical properties of NFC and CNC suggested their potential in various applications.

Preliminary Characterization of a Spray-Dried Hydrocolloid from a High Andean Algae (Nostoc sphaericum)

The search for new natural sources of hydrocolloids with stabilizing, thickening, and good binding capacity, from raw materials that are environmentally friendly and that contribute to the circular economy is a challenge for the food industry. The aim of the study was the preliminary characterization of a spray-dried hydrocolloid from high Andean algae Nostoc sphaericum. Four ecotypes of algae from Peruvian high Andean lagoons located above 4000 m were considered. The samples were collected in the period March−April 2021 and were subjected to a spray drying process in an aqueous medium. The characterization showed that the dehydrated nostoc ecotypes presented high protein and carbohydrate content, making it a potential material for direct use as a functional food for humans. The spray-dried product presented good stability for its use as a hydrocolloid, with zeta potential values (ζ), around 30 mV, evidencing the presence of -CO-, -OH, -COO-, and -CH groups, characteristic of polysaccharides, representing 40% of total organic carbon on average, giving it low water activity values and particle size at the nanometric level. Major minerals such as Ca (>277 mg/100 g), Mg (>19.7 mg/100 g), and Fe (>7.7 mg/100 g) were reported. Spray-dried nostoc is a hydrocolloid material with high potential for the food industry, with good nutritional content and techno-functional behavior.

Preparation and characterization of cellulose nanocrystals from spent edible fungus substrate

BACKGROUND

Spent edible fungus substrates were identified as potential sources to produce cellulose derivatives, namely purified cellulose and dicarboxyl cellulose nanocrystal (DCNC). Purified celluloses were obtained via chemical treatments and then oxidized by sequential periodate-chlorite without mechanical process. The structural properties of the DCNCs were characterized by transmission electron microscopy (TEM), Fourier-transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) and thermal gravimetric analysis (TGA).

RESULTS

XRD results showed that the cellulose I structure was maintained, however, the crystallinity index decreased after oxidation process. The initial pyrolysis temperature of DCNCs ranged from 242 to 344 °C. TEM results revealed that DCNC was rod-shaped with an average length and width of 130.88 nm and 7.3 nm, respectively. The average specific surface area (SSA) was 366.67 m²  g^-1 . The carboxyl content was around 3.485 mmol g^-1 . Finally, the adsorption capacity for contaminations was 76.98, 126.22, 64.44 and 9.63 mg g^-1 for copper ion (Cu²⁺ ), lead ion (Pb²⁺ ), chromium (Cr³⁺ ) and amoxicillin (AMX), respectively.

CONCLUSION

This work showed a sequentially chemical oxidation for preparing nanocellulose from secondary agricultural waste with many functional applications. © 2021 Society of Chemical Industry.

Preparation and Evaluation of Undaria pinnatifida Nanocellulose in Fabricating Pickering Emulsions for Protection of Astaxanthin

Pickering emulsions stabilized from natural sources are often used to load unstable bio-active ingredients, such as astaxanthin (AXT), to improve their functionality. In this study, AXT-loaded Pickering emulsions were successfully prepared by 2,2,6,6-tetramethy-1-piperidine oxide (TEMPO)-oxidized cellulose nanofibers (TOCNFs) from Undaria pinnatifida. The morphology analysis showed that TOCNFs had a high aspect ratio and dispersibility, which could effectively prevent the aggregation of oil droplets. The stable emulsion was obtained after exploring the influence of different factors (ultrasonic intensity, TOCNFs concentration, pH, and ionic strength). As expected, AXT-loaded Pickering emulsions showed good stability at 50 °C and 14 days of storage. The results of simulated in vitro digestion showed that the emulsions exhibited higher release of free fatty acids (FFAs) and bioaccessibility of AXT than those in sunflower oil. Hence, our work brought new insights into the preparation of Pickering emulsions and their applications in protection and sustained, controlled release of AXT.

Manufacturing of macroporous cellulose monolith from green macroalgae and its application for wastewater treatment

Enormous interest in using marine biomass as a sustainable resource for water treatment has been manifested over the past few decades. Herein, the objective was to investigate the possible use of green macroalgae (Codium tomentosum) for cellulose-based foam production through a versatile and convenient process. Macroporous cellulose monolith was prepared from cellulose hydrogel using freeze-drying process, resulting in a mechanically rigid monolith with a high swelling ratio. The as-produced spongy-like porous cellulosic material was used as bio-sorbent for wastewater treatment, particularly for removing methylene blue (MB) dye from concentrated aqueous solution. The adsorption capacity of MB was subsequently studied, and the effect of adsorption process parameters was determined in a controlled batch system. From the kinetic studies, it was found that the adsorption equilibrium was reached within 660 min. Furthermore, the analysis of the adsorption kinetics reveals that the data could be fitted by a pseudo-second order model, while the adsorption isotherm could be described by Langmuir isotherm model. The maximum adsorption capacity was found to be 454 mg/g. The findings suggested that the produced cellulose monolith could be used as a sustainable adsorbent for water treatment.

Sustainable Production of Stiff and Crystalline Bacterial Cellulose from Orange Peel Extract

In this work, a potentially economic and environmentally friendly method for the synthesis of bacterial cellulose (BC) by Gluconacetobacter xylinus from a biomass containing orange peel extract was evaluated. Orange peel extract was used as a culture medium without any hydrolysis treatment, thus speeding up the synthesis procedure. The efficacy of orange peel as a carbon source was compared with that of sucrose. The orange peel extract formed thicker cellulose gels than those formed using sucrose. X-ray diffraction (XRD) revealed both a high crystallinity index and crystallite size of BC nanofibers in samples obtained from orange peel (BC_Orange). Field emission scanning electron microscopy (FE-SEM) revealed a highly densely packed nanofibrous structure (50 nm in diameter). BC_Orange presented a two-fold increase in water holding capacity (WHC), and dynamic mechanical analysis (DMA) showed a 44% increase in storage modulus compared to sucrose derived BC. These results showed that the naturally available carbon sources derived from orange peel extract can be effectively used for BC production. The orange-based culture medium can be considered a profitable alternative to the generation of high-value products in a virtuous circular economy model.

Lytic polysaccharide monooxygenases as powerful tools in enzymatically assisted preparation of nano-scaled cellulose from lignocellulose: A review

Nanocellulose, either in the form of fibers or crystals, constitutes a renewable, biobased, biocompatible material with advantageous mechanical properties that can be isolated from lignocellulosic biomass. Enzyme-assisted isolation of nanocellulose is an attractive, environmentally friendly approach that leads to products of higher quality compared to their chemically prepared counterparts. Lytic polysaccharide monooxygenases (LPMOs) are enzymes that oxidatively cleave the β-1,4-glycosidic bond of polysaccharides upon activation of O₂ or H₂O₂ and presence of an electron donor. Their use for treatment of cellulose fibers towards the preparation of nano-scaled cellulose is related to the ability of LPMOs to create nicking points on the fiber surface, thus facilitating fiber disruption and separation. The aim of this review is to describe the mode of action of LPMOs on cellulose fibers towards the isolation of nanostructures, thus highlighting their great potential for the production of nanocellulose as a novel value added product from lignocellulose.